World of Automation - Hiquel

More documents

Recommendations

Info

TS overview single or dual supply voltage options 2 x SPNO output relay 2 star period time ranges 4 dwell times selected by dip switch LED indicators for power supply and relay status 22.5mm DIN rail mount housing or 11pin plug in housing supply voltage variation frequency range max. delay time repeat accuracy output relay specification Ue/Ie AC-15* Ue/Ie DC-13* expected life time operating conditions specification ordering information part no supply output relay type Gehäusetypen housing type other voltages on request nominal voltage +10% / -15% 48-63Hz 100% of the selected range < 1% of the selected range max. 10A 230V~ 120V/5A 240V/4A 24V/4A SPNO 1x10 7 operations 1x10 5 mechanical electrical operations screws pozidrive 1 screw tightening torque 0,6..0,8Nm TS02 TS03 TS05 TS06 TS42 TS44 TS72 TS74 230V~ 24V~= 115V~ 415V~ 230V~ / 24V~= 115V~ / 24V~= 230V~ w. transf. 115V~ w. transf. -20 to +60°C non condensing 6VA 1W 6VA 6VA 6VA/1W 6VA/1W 2VA 2VA * EN 60947-5-1 VDE 0435 2 SPNO 2 SPNO 2 SPNO 2 SPNO 2 SPNO 2 SPNO 2 SPNO 2 SPNO HIQUEL 2009 X01.00 - - - - - - - - Star-delta start timer R1 R2 HIGH QUALITY ELECTRONICS Supply voltage on Supply voltage off Output relay contact closed Output relay contact open U t1 Remove supply voltage before making any changes to either time range or timing function. On the application of the supply voltage the star relay pulls in immediately for the duration of the star time set. When the star time expires the star relay drops out and the dwell time begins. At the end of the dwell time the delta relay pulls in. When the supply voltage is removed the delta relay drops out and the time relay resets ready for the next timing cycle. Time ranges star time (=t1) required delay time is set using the potentiometer on the front plate 0,8s- 8,0s 6,0s- 60s dwell time (=t2) 40ms 60ms 80ms 100ms +~ A1 2 A2 10 -~ 16 4 yes yes yes yes no no no no t2 Supply = U = A1-A2 > > 15 1 R1 R2 t1 t1+t2 18 3 A A A A G G G G 2 DIN 11 C US 3:12 star-delta start timer
asymmetrical recycler 3:13 1 DIN Asymmetrical recycler R-func. B1 R-func. X01.00 Supply voltage (U) on Supply voltage (U) off Starting contact S on B1 closed Starting contact S on B1 open Time 1 (t1) is running Time 2 (t2) is running U Ii Ip hn hv Iihn/hv Iphn/hv Functions: li...Asymmetrical recycler pulse first lp...Asymmetrical recycler pause first lihn...Asymmetrical recycler pulse first with normal inhibit lphn...Asymmetrical recycler pause first with normal inhibit lihv...Asymmetrical recycler pulse first with inverse inhibit lphv...Asymmetrical recycler pause first with inverse inhibit A24 A1 A2 B1 0,5 t1 U B1 0,1 1,0 0,5 t2 t1 t2 0,1 1,0 -/h hn/v li/lp -/- -/- -/- ITI16 115..230Vac 24Vac/dc 10s 30s1m 1s 10m t1 - 1h 10h F 1d 10d 10s30s1m 1s 10m R1 1h t2 - 10h 1d 10d 18 15 16 Time ranges 1s, 10s, 30s, 1m, 10m, 1h, 10h, 1d, 10d The required delay time within the range selected is set using the potentiometer on the front plate. 24V~ 115-230V~ A24 ~ + ~ A1 A2 ~ - B1 s 16 15 R1 18 ITI16 overview HIGH QUALITY ELECTRONICS asymmetrical recycler all common supply voltages on one unit 6 different asymmetrical functions 2 separate timers 9 selectable time ranges ‘pulse first’ or ‘pause first’ selectable function real pause function SPCO configuration LED indicators for power supply, failure, status of output relay, control contact & timer 22.5mm DIN rail mount housing specification supply voltage variation nominal voltage -20%..+10% frequency range 48-63Hz duty cycle 100% repeat accuracy
Page 1 and 2: World of Automation Chapter 3: Timi
Page 3 and 4: ITM16 overview multi-function timin
Page 5 and 6: multi-function with two time functi
Page 7 and 8: on delay 3:05 1or2 1 or 2 DIN 11 C
Page 9 and 10: symmetrical recycler 3:07 1or2 1 or
Page 11 and 12: true off delay (without supply volt
Page 13: star-delta start timer 3:11 2 PTC D
Page 17 and 18: multifunction with flip-flop 3:15 2
Page 19 and 20: on delay with constant supply, cont

World of Automation - Hiquel

Create successful ePaper yourself

Delete template?

Save as template?