Volume Control Dampers Remotely Operated Balancing Dampers ...

More documents

Recommendations

Info

American Made. World Proven. Model M/S Micro Switch Package For Combination Fire/Smoke Dampers Represented by: 6235 South Oak Park Avenue Chicago, IL 60638 USA Toll free: 800.585.7686 +1.708.552.4040 Fax: +1.708.594.0396 www.metairtech.com P-83a Rev 4 Page 2 of 2 © 2012 Metropolitan Air Technology. All rights reserved. 7/12
In today’s real world of budget cut backs and lack of time to periodically check damper operation, MAT is pleased to introduce this labor saving option. MAT, Model RCB-X, Remote Control Boxes are for use on dampers where it is desired to note dampers operation without the necessity of shutting the HVAC system down. NFPA, local and national codes state that fire and smoke dampers shall be checked periodically for operation. Most actuator manufacturer’s recommend their actuators be cycled every 6 - 12 months, to insure proper operation of the damper/actuator. This unit can be installed in the wall below the damper, a central location, mounted in the ceiling below the damper, or on the duct connected to the damper. When properly installed the building maintenance department can save as much as 70% time in locating and checking damper operation. With a simple flip of the switch and watching the lights gives you the assurance that the damper is properly working without the need for shutting the HVAC system down, removing ceiling tiles, removing duct access doors, and using a ladder and flash light to look down the duct to see if the damper is closed or open. See Control Switch Functions below for switch function. Model RCB-1: The RCB-1 is a single electrical box panel that is composed of an On/ Off switch, one red and one green light. This model can be used in conjunction with any of our combination fire/smoke dampers, smoke dampers, multi-blade fire dampers, and air control dampers with the proper options. The dampers must be ordered with one of the following options: M/S, STO/R, or DTO/R. Model RCB-2: The RCB-2 is a single electrical box panel that is composed of an On/ Off/On switch, one red and one green light. This model can be used in conjunction with our combination fire/smoke dampers that are ordered with options DTO/R. This model, when wired properly, will allow for bypassing the lower thermostatic disk (usually 165°F or 212°F). While in Bypass mode, the damper will remain open until the upper limit thermostatic disk activates (usually 250°F or 350°F depending on what is ordered). Model RCB-3: The RCB-3 is a single electrical box panel that is composed of a red and green light. This model can be used in conjunction with any of our combination fire/smoke dampers, smoke dampers, multi-blade fire dampers, and air control dampers with the proper options. The dampers must be ordered with one of the following options: M/S, STO/R, or DTO/R. This model only incorporates lights for visual observation of the dampers’ blade position. American Made. World Proven. Model RCB-1, RCB-2, RCB-3, RCB-4 (Remote Control Box ) For Multi-Blade Dampers 6235 South Oak Park Avenue Chicago, IL 60638 USA Represented by: Toll free: 800.585.7686 +1.708.552.4040 Fax: +1.708.594.0396 www.metairtech.com Model RCB-4: The RCB-4 is a RCB-1 or RCB-2 box that has a Keyed switch for security controlled operation or inspection of dampers. The switch only controls the operation of the damper. The operation of the lights is independent of the switch position. Refer to RCB-1 or RCB-2 for more details on the specific box. Control Switch Functions: Normal/Open: Switch in this position allows the damper to operate as if it was wired directly to a smoke detector or other power source. The damper remains open until the power source is disconnected from a smoke detector signal, fan interlock, etc or until the temperature in the duct elevates above the heat responsive device located on the damper. Closed: Switch in this position, disconnects power to the actuator, thus allowing the damper to close. It will remain closed until the switch is positioned into the normal/ open position regardless of any input signals. This wording is only used on RCB-1 only. Off: Switch in this position, disconnects power to the actuator, thus allowing the damper to close. It will remain closed until the switch is positioned into the normal/open position regardless of any input signals. This wording is only used on RCB-2 only when used in conjunction with a DTO/R option. By-pass: Switch in this position, the operator is allowed to by-pass the low temperature thermostat, thus opening the damper until the air in the duct elevates to high temperature thermostat limit. At this time the damper will close and cannot be re-opened. Green Light (Open): This light is wired in series with the micro-switch package and indicates when the blades are open. Standard ratings for this light are 120vac. 24 vac and Direct Current (vdc) lights will need voltage noted on order and ordered special. Red Light (Closed): This light is wired in series with the micro-switch package and indicates when the blades are closed. Standard ratings for this light are 120vac. 24 vac and Direct Current (vdc) lights will need voltage noted on order and ordered special. © 2012 Metropolitan Air Technology. All rights reserved. 7/12 P-84 Rev 4 Page 1 of 2
Page 1 and 2:
Volume Control Dampers Remotely Ope
Page 3 and 4:
Combination Fire/Smoke Dampers (con
Page 5 and 6:
American Made. World Proven. Model
Page 7 and 8:
Options • 3 Hour Rating • Retai
Page 9 and 10:
American Made. World Proven. Due to
Page 11 and 12:
Page 13 and 14:
Transitions for Type C Dampers Amer
Page 15 and 16:
FD-B American Made. World Proven. M
Page 17 and 18:
Options • Factory Sleeve (20 Ga m
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Transitions for Type C Dampers FDD-
Page 25 and 26:
Page 27 and 28:
(38.1mm) American Made. World Prove
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Grille or Register by others FD-AOW
Page 39 and 40:
Page 41 and 42:
(-CR) Options • Factory Sleeve (1
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
4. Methods of Securing Damper in Op
Page 55 and 56:
American Made. World Proven. Fire D
Page 57 and 58:
3. Methods of Securing Damper in Op
Page 59 and 60:
American Made. World Proven. Fire &
Page 61 and 62:
6B. Option 2: The damper may also b
Page 63 and 64:
These installation instructions app
Page 65 and 66:
Fabrication of Horizontal to Vertic
Page 67 and 68:
© 2012 Metropolitan Air Technology
Page 69 and 70:
F/S-3V-I (1-1/2 hour), F/S-3V-3-I (
Page 71 and 72:
Options • Factory sleeves (20 Ga
Page 73 and 74:
Performance Data Pressure drop test
Page 75 and 76:
Page 77 and 78:
Options • Factory sleeves (20 Ga
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
F/S-3V-FA-I (1-1/2 hour) American M
Page 87 and 88:
Options • Transitions • Round o
Page 89 and 90:
Page 91 and 92:
F/S-3V-OW-I (1-1/2 hour) American M
Page 93 and 94:
F/S-3V-OW-II (1-1/2 hour) American
Page 95 and 96:
F/S-AF-OW-I (1-1/2 hour) American M
Page 97 and 98:
F/S-AF-OW-II (1-1/2 hour) American
Page 99 and 100:
F/S-AF-FA-I (1-1/2 hour) American M
Page 101 and 102:
F/S-AF-FA-II (1-1/2 hour) American
Page 103 and 104:
Page 105 and 106:
Page 107 and 108: 4. Methods of Securing Damper in Op
Page 109 and 110: American Made. World Proven. Combin
Page 111 and 112: 3. Methods of Securing Damper in Op
Page 113 and 114: American Made. World Proven. Out Of
Page 115 and 116: American Made. World Proven. Model
Page 117 and 118: Standard Construction Damper and sl
Page 127 and 128: UL 555S Classified at 250 °F or 35
Page 129 and 130: UL 555S Classified at 250 °F or 35
Page 133 and 134: Note • Remote Control Boxes are s
Page 135 and 136: American Made. World Proven. Motor/
Page 137 and 138: P-68a Page
Page 139 and 140: P-68b Page 2
Page 141 and 142: P-68c Page 2
Page 143 and 144: Standard Construction: Sleeve:20 ga
Page 145 and 146: These installation instructions app
Page 147 and 148: Fabrication of Horizontal to Vertic
Page 149 and 150: Manufacturer’s Recommendations Al
Page 151 and 152: Suggested Specification Low Leakage
Page 153 and 154: Due to continuing research, MAT res
Page 155 and 156: Suggested Specification Low Leakage
Page 157: The M/S Switch Package provides the
Page 161 and 162: Installation Details 1. Dampers sho
Page 163 and 164: Standard Construction: Sleeve:20 ga
Page 165 and 166: American Made. World Proven. Motor/
Page 167 and 168: © 2012 Metropolitan Air Technology
Page 173 and 174: Suggested Specification Square to r
Page 175 and 176: American Made. World Proven. Due to
Page 177 and 178: MODEL NO. C/FS C/FSB C/FSX C/FS-2F
Page 179 and 180: For Models C/FSX (See Fig. 1, Page
Page 181 and 182: Ducted and Ductless Surface Mounted
Page 183 and 184: American Made. World Proven. Metrop
Page 185 and 186: American Made. World Proven. Inspec
Page 187 and 188: American Made. World Proven. Inspec
Page 189 and 190: Xx Xx American Made. World Proven.
Page 191 and 192: Xx Xx American Made. World Proven.
show all

Volume Control Dampers Remotely Operated Balancing Dampers ...

Create successful ePaper yourself

Delete template?

Save as template?