Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Forged Mold Clamps<br />
Open Toe Clamp<br />
For use on injection molds where it is preferred<br />
to slip clamps off their platen bolts during<br />
mold changes. Fully adjustable, these clamps<br />
are suitable for use on any mold having height<br />
or flange height between 15 ⁄32" and 2". Proper<br />
application and method of adjustment is shown<br />
below. Forged of hi-tensile steel, hardened and<br />
black oxide finished, clamps are available in<br />
lengths of 5 1 ⁄4" and 7" to fit platen bolt holes of<br />
5 ⁄8" and 3 ⁄4" diameter.<br />
Forged Mold Clamps<br />
Closed Toe Clamp<br />
For use on injection molds where the molders preference is<br />
to hang clamps on their platen bolts during mold changes.<br />
Fully adjustable, these clamps are suitable for use on any<br />
mold having height or flange height between 15 ⁄32" and 2".<br />
Proper application and method of adjustment is<br />
shown below. Forged of hi-tensile steel,<br />
hardened and black oxide finished,<br />
clamps are available in lengths<br />
of 5 1 ⁄4", 7", 9 1 ⁄2" and 12" (also<br />
machined clamps of 4", 10" and<br />
13") to fit platen bolt holes of 5 ⁄8", 3 ⁄4",<br />
1" and 1 1 ⁄4" (16, 20, 24 and 32mm)<br />
diameter.<br />
FIGURE 1<br />
FIGURE 2<br />
Adjusting Screw<br />
Fig 1: Most standard molds have 13 ⁄16" wide slot (for clamp<br />
tongue) and( 29 ⁄32" dimension from base (platen surface) to slot.<br />
When using this type mold, the clamp is installed heel down<br />
with a regular length bolt, usually 3 1 ⁄2" and no adjusting<br />
screw.<br />
FIGURE 3<br />
Fig 2: If the clamping flange is of 15 ⁄32" to<br />
29 ⁄32" thickness, the clamp may be turned<br />
over and installed heel up; flat side<br />
down, with the adjusting screw on the<br />
flat side.<br />
Adjusting Screw<br />
Fig 3: In the event of a clamping flange height of 29 ⁄32" to 2",<br />
or no flange at all, the clamp may again be used in the heel<br />
down position with the adjusting screw and a longer bolt<br />
which will allow for holding power without the danger of<br />
stripping platen threads.<br />
216<br />
featuring the best of:<br />
Northern Supply (800-365-6565) • Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
4 1 ⁄4” Closed Toe Clamp-- 1 ⁄2”-13 Platen Hole<br />
(or 12/1.75mm)<br />
Grade 5 Hex Head Bolt<br />
Use bolt length which allows a minimum of one times the<br />
diameter of the thread in length of thread in the platen<br />
Adjusting Screw<br />
Use adjusting screw if required,<br />
to ensure that the clamp is parallel<br />
to the platen for maximum strength.<br />
Hardened Mold Clamp Washer<br />
Forged T-Slot Bolt<br />
Case Hardened Hex Nuts<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC0FC 4 1/4”Closed Toe Clamp $12.50 $12.00<br />
HHB5025 Grade 5 Hex Head Bolt - 2 1 ⁄2" Under Head $0.28 $0.26<br />
HHB5030 Grade 5 Hex Head Bolt - 3" Under Head $0.33 $0.30<br />
HHB5035 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.39 $0.36<br />
ASO Adjusting Screw - 1 1/2" Thread Length $2.97 $2.81<br />
W1 Mold Clamp Washer - 9 ⁄16" I.D., 1 1 ⁄8" O.D. 1 ⁄4" Thickness $0.67 $0.63<br />
TS42 1/2 Forged T-Slot Bolt - 2 1 ⁄2" Overall Length $3.85 $3.71<br />
HX4 Case Hardend Hex Nut - 7 ⁄8" Across Flats $1.15 $1.04<br />
featuring the best of:<br />
217<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
5 1 ⁄4” Closed Toe Clamp-- 5 ⁄8”-11 Platen Holes<br />
(or 16/2mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC1FC 5 1 ⁄4" Closed Toe Clamp $14.00 $13.50<br />
HHB6230 Grade 5 Hex Head Bolt - 3" Under Head $0.53 $0.50<br />
HHB6235 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.61 $0.57<br />
HHB6240 Grade 5 Hex Head Bolt - 4" Under Head $0.67 $0.63<br />
HHB6245 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $0.91 $0.84<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W2 Hardened Mold Clamp Washer - 11 ⁄16" I.D., 1 1 ⁄4" O.D. 1 ⁄4" Thickness $0.77 $0.73<br />
WF2 Forged No-Turn Washers for 5 ⁄8"-11 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-585 Extra Large Adjusting Screw - 3" Overall Length $8.00 $7.85<br />
TS54 1/2 Forged T-Slot Bolt - 4 1 ⁄2" Overall Length $5.09 $4.90<br />
HX5 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄6" Across Flats $1.73 $1.62<br />
218<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
5 1 ⁄4” Open Toe Clamp-- 5 ⁄8”-11 Platen Holes<br />
(or 16/2mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC1FO 5 1 ⁄4" Open Toe Clamp $14.00 $13.50<br />
HHB6230 Grade 5 Hex Head Bolt - 3" Under Head $0.53 $0.50<br />
HHB6235 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.61 $0.57<br />
HHB6240 Grade 5 Hex Head Bolt - 4" Under Head $0.67 $0.63<br />
HHB6245 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $0.91 $0.84<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W2 Mold Clamp Washer - 11 ⁄16" I.D., 1 1 ⁄4" O.D. 1 ⁄4" Thickness $0.77 $0.73<br />
WF2 Forged No-Turn Washers for 5 ⁄8"-11 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-585 Extra Large Adjusting Screw - 3" Overall Length $8.00 $7.85<br />
TS54 1/2 Forged T-Slot Bolt - 4 1 ⁄2" Overall Length $5.09 $4.90<br />
HX5 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄6" Across Flats $1.73 $1.62<br />
featuring the best of:<br />
219<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
5 1 ⁄4” Closed Toe Clamp-- 3 ⁄4”-10 Platen Hole<br />
(or 20mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC2FC 5 1 ⁄4" Closed Toe Clamp $14.00 $13.50<br />
HHB7530 Grade 5 Hex Head Bolt - 3" Under Head $0.80 $0.74<br />
HHB7535 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.99 $0.92<br />
HHB7540 Grade 5 Hex Head Bolt - 4" Under Head $1.06 $0.99<br />
HHB7545 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $1.16 $1.08<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W3 Mold Clamp Washer - 13 ⁄16" I.D., 1 1 ⁄2" O.D. 1 ⁄4" Thickness $0.88 $0.84<br />
WF3 Forged No-Turn Washers for 3 ⁄4"-10 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-755 Extra Large Adjusting Screw - 3 1 ⁄2" Overall Length $9.50 $8.79<br />
TS65 Forged T-Slot Bolt - 5" Overall Length $7.22 $6.96<br />
HX6 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄4" Across Flats $1.95 $1.82<br />
220<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
5 1 ⁄4” Open Toe Clamp-- 3 ⁄4”-10 Platen Hole<br />
(or 20mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC2FO 5 1 ⁄4" Open Toe Clamp $14.00 $13.50<br />
HHB7530 Grade 5 Hex Head Bolt - 3" Under Head $0.80 $0.74<br />
HHB7535 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.99 $0.92<br />
HHB7540 Grade 5 Hex Head Bolt - 4" Under Head $1.06 $0.99<br />
HHB7545 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $1.16 $1.08<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W3 Mold Clamp Washer - 13 ⁄16" I.D., 1 1 ⁄2" O.D. 1 ⁄4" Thickness $0.88 $0.84<br />
WF3 Forged No-Turn Washers for 3 ⁄4"-10 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-755 Extra Large Adjusting Screw - 3 1 ⁄2" Overall Length $9.50 $8.79<br />
TS65 Forged T-Slot Bolt - 5" Overall Length $7.22 $6.96<br />
HX6 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄4" Across Flats $1.95 $1.82<br />
featuring the best of:<br />
221<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
7” Closed Toe Clamp-- 5 ⁄8”-11 Platen Hole<br />
(or 16/2mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC3FC 7" Closed Toe Clamp $19.50 $18.50<br />
HHB6230 Grade 5 Hex Head Bolt - 3" Under Head $0.53 $0.50<br />
HHB6235 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.61 $0.57<br />
HHB6240 Grade 5 Hex Head Bolt - 4" Under Head $0.67 $0.63<br />
HHB6245 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $0.91 $0.84<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W2 Mold Clamp Washer - 11 ⁄16" I.D., 1 1 ⁄4" O.D. 1 ⁄4" Thickness $0.77 $0.73<br />
WF2 Forged No-Turn Washers for 5 ⁄8"-11 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-585 Extra Large Adjusting Screw - 3" Overall Length $8.00 $7.85<br />
TS52 1/2 Forged T-Slot Bolt - 4 1 ⁄2" Overall Length $4.55 $4.38<br />
HX5 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄6" Across Flats $1.73 $1.62<br />
222<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
7” Open Toe Clamp-- 5 ⁄8”-11 Platen Hole<br />
(or 16/2mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC3FO 7" Open Toe clamp $20.00 $19.00<br />
HHB6230 Grade 5 Hex Head Bolt - 3" Under Head $0.53 $0.50<br />
HHB6235 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.61 $0.57<br />
HHB6240 Grade 5 Hex Head Bolt - 4" Under Head $0.67 $0.63<br />
HHB6245 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $0.91 $0.84<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W2 Mold Clamp Washer - 11 ⁄16" I.D., 1 1 ⁄4" O.D. 1 ⁄4" Thickness $0.77 $0.73<br />
WF2 Forged No-Turn Washers for 5 ⁄8"-11 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-585 Extra Large Adjusting Screw - 3" Overall Length $8.00 $7.85<br />
TS54 1/2 Forged T-Slot Bolt - 4 1 ⁄2" Overall Length $5.09 $4.90<br />
HX5 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄6" Across Flats $1.73 $1.62<br />
featuring the best of:<br />
223<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
7” Closed Toe Clamp-- 3 ⁄4”-10 Platen Hole<br />
(or 20/2.5mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC4FC 7" Closed Toe Clamp $19.50 $18.50<br />
HHB7530 Grade 5 Hex Head Bolt - 3" Under Head $0.80 $0.74<br />
HHB7535 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.99 $0.92<br />
HHB7540 Grade 5 Hex Head Bolt - 4" Under Head $1.06 $0.99<br />
HHB7545 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $1.16 $1.08<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W3 Mold Clamp Washer - 13 ⁄16" I.D., 1 1 ⁄2" O.D. 1 ⁄4" Thickness $0.88 $0.84<br />
WF3 Forged No-Turn Washers for 3 ⁄4"-10 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-755 Extra Large Adjusting Screw - 3 1/2" Overall Length $9.50 $8.79<br />
TS65 Forged T-Slot Bolt - 5" Overall Length $7.22 $6.96<br />
HX6 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄4" Across Flats $1.95 $1.82<br />
224<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
7” Open Toe Clamp-- 3 ⁄4”-10 Platen Hole<br />
(or 20/2.5mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC4FO 7" Open Toe Clamp $20.00 $19.00<br />
HHB7530 Grade 5 Hex Head Bolt - 3" Under Head $0.80 $0.74<br />
HHB7535 Grade 5 Hex Head Bolt - 3 1 ⁄2" Under Head $0.99 $0.92<br />
HHB7540 Grade 5 Hex Head Bolt - 4" Under Head $1.06 $0.99<br />
HHB7545 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $1.16 $1.08<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W3 Mold Clamp Washer - 13 ⁄16" I.D., 1 1 ⁄2" O.D. 1 ⁄4" Thickness $0.88 $0.84<br />
WF3 Forged No-Turn Washers for 3 ⁄4"-10 Thread, 2 1 ⁄4" Length $2.25 $2.15<br />
H-755 Extra Large Adjusting Screw - 3 1 ⁄2" Overall Length $9.50 $8.79<br />
TS65 Forged T-Slot Bolt - 5" Overall Length $7.22 $6.96<br />
HX6 Case Hardend Hex Nut for T-Slot Bolts - 1 1 ⁄4" Across Flats $1.95 $1.82<br />
featuring the best of:<br />
225<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
7” Closed Toe Clamp--1”-8 Platen Hole<br />
(or 24/3mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC5FC 7" Closed Toe Clamp $22.00 $21.00<br />
HHB1040 Grade 5 Hex Head Bolt - 4" Under Head $1.86 $1.73<br />
HHB1045 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $2.13 $1.98<br />
HHB1050 Grade 5 Hex Head Bolt - 5" Under Head $2.30 $2.14<br />
AS1 Adjusting Screw - 1 1 ⁄2" Thread Length $3.00 $2.85<br />
W4 Mold Clamp Washer -1 1 ⁄16" I.D., 1 3 ⁄4" O.D. 5 ⁄16" Thickness $1.60 $1.52<br />
WF4 Forged No-Turn Washers for 1"-8 Thread, 2 1 ⁄4" Length $4.75 $4.50<br />
H-1005 Extra Large Adjusting Screw - 3 1 ⁄2" Overall Length $15.50 $15.20<br />
TS86 Forged T-Slot Bolt - 6" Overall Length $19.71 $18.98<br />
HX8 Case Hardend Hex Nut for T-Slot Bolts 1 5 ⁄8" Across Flats $4.10 $3.90<br />
226<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)
Forged Mold Clamps<br />
9 1 ⁄2” Closed Toe Clamp--1”-8 Platen Hole<br />
(or 24/3mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC9FC 9 1 ⁄2” Closed Toe Clamp $34.00 $33.00<br />
HHB1040 Grade 5 Hex Head Bolt - 4" Under Head $1.86 $1.73<br />
HHB1045 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $2.13 $1.98<br />
HHB1050 Grade 5 Hex Head Bolt - 5" Under Head $2.30 $2.14<br />
AS2 Adjusting Screw - 2" Thread Length $4.50 $4.25<br />
W4 Mold Clamp Washer -1 1 ⁄16" I.D., 1 3 ⁄4" O.D. 5 ⁄16" Thickness $1.60 $1.52<br />
WF4 Forged No-Turn Washers for 1"-8 Thread, 2 1 ⁄4" Length $4.75 $4.50<br />
H-1005 Extra Large Adjusting Screw - 3 1 ⁄2" Overall Length $15.50 $15.20<br />
TS86 Forged T-Slot Bolt - 6" Overall Length $19.71 $18.98<br />
HX8 Case Hardend Hex Nut for T-Slot Bolts 1 5 ⁄8" Across Flats $4.10 $3.90<br />
featuring the best of:<br />
227<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)<br />
B
Forged Mold Clamps<br />
12” Closed Toe Clamp--1 1 ⁄4”-7 Platen Hole<br />
(or 30mm)<br />
Use adjusting screw if<br />
required, to ensure that<br />
the clamp is parallel to<br />
the platen for maximum<br />
strength.<br />
Use bolt length which allows<br />
a minimum of one times the<br />
diameter of the thread in length<br />
of thread in the platen<br />
Part Price Each<br />
Number Description 1-8 9+<br />
AC12FC 12" Closed Toe Clamp $45.00 $44.50<br />
HHB1240 Grade 5 Hex Head Bolt - 4 1 ⁄2" Under Head $7.91 $7.36<br />
HHB1250 Grade 5 Hex Head Bolt - 5" Under Head $8.39 $7.80<br />
HHB1260 Grade 5 Hex Head Bolt - 6" Under Head $9.35 $8.70<br />
AS3 Adjusting Screw - 2" Thread Length $5.50 $5.25<br />
W5 Mold Clamp Washer -1 5 ⁄16" I.D., 2 1 ⁄2" O.D. 1 ⁄2" Thickness $4.65 $4.40<br />
WF5 Forged No-Turn Washers for 1 1 ⁄4"-7 Thread, 2 1 ⁄4" Length $5.75 $5.50<br />
H1505 Extra Large Adjusting Screw - 5 5 ⁄8" Overall Length $29.00 $26.84<br />
228<br />
featuring the best of:<br />
Northern Supply (800-365-6565) Nickerson Machinery (800-821-9534) • OHS (Ontario-888-809-7050/Quebec-888-475-9224)