Primary Tillage - SDI-AG

RECOMMENDED PTO HP FOR 650 FLEX-FOLD DISKS
WORKING
WIDTH
BLADE
SPACING
LIGHT
DRAFT
MEDIUM
DRAFT
HEAVY
DRAFT
23-ft.
9-in.
9in.
25-ft.
0-in.
9F/11R
or
11-in.
26-ft.
8-in.
26-ft.
9-in.
Weight per blade. A weight of
167 to 207 pounds per blade gives
maximum ground penetration.
Choose 24- or 26-inch-diameter
blades to handle tough disking jobs.
Tandem Walk-Over mainframe
wheels are a 650 Disk exclusive.
They pivot up and down to give you
a smoother ride over piles of residue
and other obstacles.
29-ft.
6-in.
9in. 9F/11R 9in.
30-ft.
3-in.
9F/11R
or
11-in.
32-ft.
0-in.
32-ft.
4-in.
9F/11R 9in.
190 220 220 220 250 270 270 270
225 250 250 250 300 335 335 335
270 330 330 330 350 400 400 400
Light draft: heavy soils, dry/hard conditions, level terrain. Medium draft: average conditions.
Heavy draft: light or sandy soils, medium moisture, rolling terrain.
The 650’s heavy-duty 5.5-inchdiameter
spools have a thick,
3⁄16-inch wall to take plenty of
pounding. The larger-diameter
surface also provides extra blade
support to reduce blade breakage.
650 Specifications
MODEL
SIZES/SPACING
MEDIUM FLEX-FOLD WIDE FLEX-FOLD
9-in. (230 mm) front and rear spacing 23 ft. 9 in. (7.2 m) / 26 ft. 8 in. (8.1 m) 29 ft. 6 in. (8.9 m) / 32 ft. 4 in. (9.8 m)
11-in. (280 mm) front and rear spacing 25 ft. 0 in. (7.6 m) 30 ft. 3 in. (9.2 m)
9-in. (230 mm) front /11-in. (280 mm) rear spacing
FRAMES
26 ft. 9 in. (8.1 m) / 26 ft. 9 in. (8.1 m) 30 ft. 3 in. (9.2 m) / 32 ft. 0 in. (9.7 m)
Main 7x7x.9375 in. (177x177x8 mm) 7x7x.9375 in. (177x177x8 mm)
Inside 5x7x.9375 in. (127x177x8 mm) 5x7x.9375 in. (177x177x8 mm)
Outside wing
WEIGHT/BLADE AVERAGE*
5x7x.5 in. (127x177x13 mm) 5x7x.375 in. (177x177x9.5 mm)
9-in. (230 mm) spacing 177 lb. (80 kg) 167 lb. (76 kg)
11-in. (280 mm) spacing 207 lb. (94 kg) 196 lb. (89 kg)
9-in. (230 mm) front/11-in. (280 mm) rear spacing
GANG ANGLE (FIXED)
182 lb. (83 kg) 175 lb. (79 kg)
GANG COMPONENTS
22 deg. F/20 deg. R 22 deg. F/20 deg. R
Main tube (front) 4x6x.375 in. (102x152x9.5 mm) 4x6x.375 in. (102x152x9.5 mm)
Main tube (rear) 4x6x.9375 in. (102x152x8 mm) 4x6x.9375 in. (102x152x8 mm)
Wing tube (front) 4x6x.9375 in. (102x152x8 mm) 4x6x.9375 in. (102x152x8 mm)
Wing tube (rear) 4x6x.9375 in. (102x152x8 mm) 4x6x.9375 in. (102x152x8 mm)
Bolt 1.25-in. square (31.75 mm) 1.25-in. square (31.75 mm)
Welded spool diameter 5.5 in. (139 mm) 5.5 in. (139 mm)
Bearings Dura-Flex Dura-Flex
Furrow filler Integral Integral
Scrapers
C-CUSHIONED MIDDLEBREAKER
Combination Combination
Standard Standard
Middlebreaker blade
Spherical, 6 in. (152 mm)
smaller than base blades
Spherical, 6 in. (152 mm)
smaller than base blades
WING FLEX
Up 12 degrees 12 degrees
Down 7 degrees 7 degrees
TRANSPORT DIMENSIONS
Width 17 ft. 8 in. (5.4 m) 17 ft. 8 in. (5.4 m)
Height 11 ft. 0 in. (3.3 m) 13 ft. 8 in. (4.1 m)
Length 26 ft. 0 in. (7.9 m) 27 ft. 8 in. (8.4 m)
HYDRAULIC CYLINDERS
Wingfold 4x32 in. (102x813 mm) 4.5x32 in. (114x813 mm)
Mainframe wheels 4x8 in. (102x203 mm)** 4.5x8 in. (114x203 mm)**
Wing wheels 3.75x8 in. (95x203 mm)** 4.25x8 in. (114x203 mm)**
TIRES
Mainframe Four 11L–15 in., 10 PR Four 11L–15 in., FI LRD
Wingframe Two 11L–15 in., 10 PR Four 11L–15 in., FI LRD
HITCH PIN HOLE DIAMETER
2.25 in. (57 mm) 2.25 in. (57 mm)
SAFETY FEATURES
SMV, implement warning lights with turn signal modules, hydraulic transport lockup valve,
yellow side-reflector decals, and safety chain are all standard.
ATTACHMENTS
Finishing blades, bearing wear guards, gang-nut wrenches, knockout scraper bar, front
stabilizer wheels, single-point depth-control adapter kit for Case/IH® Magnum Series Tractors,
hydraulic fore/aft leveling, hydraulic wing control.
*Weight per blade, not weight per foot of machine width, is the most accurate measure of penetration.
**Rephasing
Case is a registered trademark of the Case Corporation.
(Specifications and design subject to change without notice.)
25