Lincoln Electric Welding & Cutting Solutions Equipment Catalog

K29
Vertical Lift
Adjuster
Provides 4 inch (102
mm) hand crank
vertical adjustment of
head position. Also includes up to 3-3/4
inch (95.2 mm) in-and-out horizontal
adjustment with stops that can be
preset for simple repetition of the same
adjustment.
K96
Horizontal Head
Adjuster
Provides crank
adjustment of head
position. Has 2 inch
(51 mm) horizontal
travel.
K119
Flux Cone
Fits K113 submerged arc
guns for welding without the
Continuous Flux Feed Tank
Assembly.
K162-1
Spindle Adapter
for Readi-Reels ®
and Spools
2 inch (51 mm) O.D.
spindle for mounting Readi-Reels ® and 2
inch (51 mm I.D. spools up to 60 lb. (27.2
kg) capacity to custom installations.
K163
Undercarriage
Includes
mounting frame,
front casters,
rear wheels and handle for hand towing.
For use with Wire Reel Stand.
K202
Burnback Kit
Provides
adjustable
delay of power
source output
shut off to prevent electrode sticking in
crater when using high wire feed speeds.
Includes a cold inch switch.
K219
Automatic
Flux Hopper
Assembly
For submerged arc
welding. Includes
electric flux valve.
K230
Butt Seam
Guide Kit
Mount in place
of the standard
front wheel
to ride in a
V-groove or open 1/8-3/8 inch (3.2-
9.5 mm) butt joint, keeping the wire in
required alignment.
K231-1
Submerged Arc Contact
Nozzle Assembly
For 5/64 thru 3/16 inch (2.0
thru 4.8 mm) wire electrode
at currents generally below
600 amps. Outer flux cone
gives full flux coverage with minimum
consumption.
K232
Horizontal
Fillet and Lap
Adapter Kit
Includes a rear
guide wheel,
head tension
spring and front guide wheel assembly
on an adjustable arm which rides in the
joint to maintain alignment and electrode
angle. Kit includes separate front guide
wheel assemblies for fillet and lap joints.
Welds to the left or right of the tractor’s
center line.
K283
Portable Digital
Wire Feed
Speed Meter
When clamped
on an exposed
section of
continuously fed electrode, unit reads wire
feed speed in inches per minute.
K285
Concentric
Flux Cone
Assembly
For use with
K148B, Positive Contact Nozzle Assembly.
Provides concentric flux coverage around
the electrode.
K299
Wire Reel Assembly
Includes wire reel for
50-60 lb. (22.7-27.2 kg)
coils, wire reel mounting
and brake.
K305
Wire Reel and
Flux Tank
Assembly
Includes flux tank,
undercarriage,
wire reel and brake assembly in open
shroud.
K334
Starting
or Crater
Module
Permits
additional
settings
of wire feed speed and voltage for an
adjustable period of time (10 seconds
max). Can be used for either a starting
procedure or a crater fill procedure. If
both are required, two assemblies must
be ordered.
K336
Remote
Interface
Module
Permits remote
operation of the
NA-5 Inch Up, Inch Down, Start and Stop
Functions by either of the following usersupplied
external signals and provides
electrical isolation of the NA-5 control
circuitry from these signals:
• Switches – Momentary closure
of contacts rated for 24 volts, 5
milliamperes, DC.
• 24 Volt Signals – Momentary application
of 24 volt ±10% AC or DC signal capable
of 5 milliamperes steady state. (.15 amp
peak capacitive in rush) per input. This
module can be used with all codes of
NA-5 Controls and replaces the earlier
K336 Remote Pushbutton Interface
Module, which provided for only external
switch closure signals.
K363P
22-30 lb. Readi-Reel ®
Adapter
Adapts 22-30 lb.
(10-14 kg) Lincoln
Electric Readi-Reels ® of
electrode to 2 inch (51 mm) spindle.
K385-2
CV Adapter
Provides constant voltage
output for semiautomatic
wire welding. Includes
14-pin MS-Type
connection and local/
remote switch.
K396
Track Section
Each section
provides 70 inch
(1.8 m) of travel.
K425
Gas Solenoid Kit
Includes solenoid
valve and
mounting bracket.
K435
14 lb. Innershield ®
Coil Adapter
Permits 14 lb. (6
kg) Innershield ®
electrode coils to
be mounted on 2 inch (51 mm) O.D.
spindles.
K468
8 inch O.D. Spool
Adapter
Permits 8 inch (200
mm) O.D. spools to be
mounted on 2 inch (51
mm) O.D. spindles.
ACCESSORIES
K484
Jumper Plug Kit
Required to close the
contactor in the power
source when the power
source is used with a remote output
contactor such as the
contactor in across-the-arc wire feeders.
K487-25
Magnum ® SG
Spool Gun
Lightweight,
well-balanced, semiautomatic spool gun
designed primarily for easy, accurate
aluminum wire feeding. Includes 25 ft.
(7.5 m) gun cable, .035 inch (0.9 mm)
contact tip installed, package of six
contact tips, 5/64 inch (2.0 mm) Allen
wrench and operating manual.
K488
SG Control Module
Provides control of
wire speed and gas
flow. For use with CV
power sources and
CV Engine Drives
with output contactor.
K492-10
Control Module
Input Cable
Terminal Strip and
Lug. Required
for connection of
control module to power source. Consists
of control and electrode cables and gas
line. 10 ft. (3.0 m). For Lincoln power
sources having terminal strip and lug
connections.
K493-10
Control Module
Input Cable
14-pin MS-type
and Twist Mate .
Required for
connection of control module to power
source. Consists of control and electrode
cables and gas line. 10 ft. (3.0 m). For
Lincoln power sources having 14-pin
MS-type control connections and
Twist Mate power connections.
K494
Gas
Solenoid
Assembly
Includes
solenoid
valve and
mounting bracket.
www.lincolnelectric.com | 125