World of Attachments - Davenport Machine

More documents

Recommendations

Info

49 EJECTOR ATTACHMENTS 1263-144-SA Burring Spindle Ejector – Six to One Ratio The six to one ejector is used to eject long parts from the burring spindle. Ejecting stroke <strong>of</strong> up to three and one quarter inches can be attained with this attachment. 1263-144-SA Burring Spindle Ejector - 6 to 1 Ratio
MB-635-30-SA and MB-635-30-1-SA Burring Spindle Chucking Mechanism A special ball chucking mechanism, for use on the burring spindle, permits opening the burring collet seven sixty-fourths <strong>of</strong> an inch on each side. This allows the burring collet to advance “over shoulders” to a machined diameter where greater chucking surface can be attained. This chucking mechanism is adaptable to either the third position burring attachment (see page 10) or the fifth position burring attachment (see page 9). MB-635-30-SA Burring Spindle Chucking Mechanism 50
Page 1 and 2: WORLD OF ATTACHMENTS
Page 3 and 4: New Davenport Servo B. The Best Pro
Page 5 and 6: Specifications for Model B Five-Spi
Page 7 and 8: INTRODUCTION This manual has been d
Page 9 and 10: 1263-201-SA Two Position Backworkin
Page 11 and 12: 1263-122-SA Third Position Stationa
Page 13 and 14: 1263-127-SA Third Position Counters
Page 15 and 16: 1263-143-SA Third Position Self Cen
Page 17 and 18: 2496-57-SA Spindle Stopping Clutch
Page 19 and 20: MB-226-54-2-3-SA Revolving Support
Page 21 and 22: 1232-98-3-SA One to One Idler Gear
Page 23 and 24: 1381-38-SA Revinloc Attachment for
Page 25 and 26: 1232-101-75-SA Rotary Slotting Atta
Page 27 and 28: 1380-SA Revinloc Attachment 1232-10
Page 29 and 30: 1232-140-SA Keyway Milling Attachme
Page 31 and 32: 1390-50-SA Straddle Mill Attachment
Page 33 and 34: 1321-SA Third Position Cross Drill
Page 35 and 36: 1615-SA Inside Cross Drill or Count
Page 37 and 38: 1428-SA/1429-SA Ninety Degree Cross
Page 39 and 40: 1373-SA Fourth Position Cross Tappi
Page 41 and 42: MBSL-200-SA Spindle Locating Attach
Page 43 and 44: SB-226-SAC Servo Threading Attachme
Page 45 and 46: 1448-SA Second Position Thread Roll
Page 47 and 48: 1244-100-SA & 1287-100-SA Transfer
Page 49: 1263-130-SA Special Ejecting Tube A
Page 53 and 54: 1263-102-43-SA Oil Sleeve Assembly
Page 55 and 56: 5080-272-SA Mounting Bracket The 50
Page 57 and 58: ALIGNING GEARS 1263-132-SA Spindle
Page 59 and 60: Parts Machined Using Spindle Aligni
Page 61 and 62: 1483-SA Third Position Tool Arm Mil
Page 63 and 64: 5080-329-50-SA Double Action Chip C
Page 65 and 66: 5080-382-75-SA Air Feed Attachment
Page 67 and 68: SPECIAL ATTACHMENTS SB-1605-SA Pneu
Page 69 and 70: SB-5080-426-62-SA Part Chute Divert
Page 71 and 72: MBLA-196-35-SA Declutch and Brake A
Page 73 and 74: By Product Number 1232-101-75-SA ..

World of Attachments - Davenport Machine

Create successful ePaper yourself

Delete template?

Save as template?