PAVING & CONCRETE PAINTS & COLOUR - Pascol Paints

Surface Preparation
The key to a successful project
To obtain the best results be sure to use Pascol Oil Stain Remover to lift stains without
scrubbing or Pascol Bond Lok to clean, etch and degrease your concrete before you begin.
Anti-Skid option
PASCOL OIL STAIN RemOveR
• Absorbs and lifts stains from
concrete without scrubbing
• Pour on and brush off
• Cleans away stains and oil spots
prior to painting or sealing
PASCOL BOND•LOKTm • Cleans, degreases and etches
concrete
• Improves penetration & adhesion
of paints & sealers
• Provides maximum durability of
top coat
The BOND-LOK ADvANTAge
Selected Pascol products contain
technologies that work to maximize the
bond between the floor coating and the
concrete. This bond extents the life of your
finish, giving you maximum durability.
PASCOL ANTI-SKID FLOOR TeXTURe
ADDITIve
For steps, pool areas, floors & porches.
Anti-Skid Floor Texture Additive will not
change the colour, properties or performance
of the coating. Particularly valuable in areas
used by children and the elderly, or areas
subject to wet conditions.
• Add Pascol Anti-Skid Floor Texture Additive
to increase traction and provide a skid
resistant surface
Pascol Products Usage Guide
Concrete Surface Preparation
CONCReTe
hINTS & TIPS
mASONRY
gARAge FLOORS
DRIveWAYS
Surface Preparation: Correctly preparing the surface is the most important step when
using Pascol Paving and Concrete Paints. This is an integral part of the process that
will allow you to achieve an amazing, long-lasting finish. It is crucial that you adhere to
all the detailed instructions on the label before you start the project.
New Concrete: New concrete surfaces must be left to cure for at least four to six
weeks before applying Pascol Paving and Concrete Paints.
Previously Painted Concrete:
• Pascol Paving and Concrete Paints can be applied to concrete surfaces that have
been previously painted. Following the instructions provided on the label will
guarantee your chosen surface is in a perfect state to be repainted.
• All loose, peeling or flaking material must be removed before application. Sand
gloss or semi-gloss enamel surfaces until gloss is removed.
PAThS
Bond-Lok * * * * * * * * * * * * * *
Paving Paints
1-Part epoxy Paving Paint * * * * * * *
Solid Colour Paving Paint * * * * * * * *
Non-Slip Paving Paint * * * * * *
Decorative Concrete Finishes
Semi-Transparent
Concrete Stain * * * * * * * * *
etching Stain & Sealer * * * * *
Clear & Waterproof Sealers
multi - Purpose Sealer * * * * * * * * *
Wet Look Sealer * * * * * * * * * *
Natural Look Sealer * * * * * * * * * * *
Application Information:
• When painting the surface it is imperative not to apply too much at once. Adhere to
the coverage level on the label to achieve the best result. Remember two coats of
paint are better than one thick layer.
• When applying paint it is best to work in section of 1 to 2 square metres at a time.
• Depending on whether you are working in cooler or humid climates, allow the paint
to dry for longer periods. In some cases allow for double the allocated drying time.
• To guarantee the correct consistency of paint colour throughout the applying
process, box and combine your required amount of paints that will be needed to
complete the project.
• Avoid painting driveways and paths during the heat of the day, as this may prevent
penetration and adhesion of the paint.
PATIOS
INTeRIOR FLOORS
BRICK
POOL DeCKS
PAveRS
STePS
AggRegATe
FLAgSTONe
SLATe
PeBBLeCReTe
mORTAR