Pascol Paving & Concrete Coatings Semi–Transparent Concrete Stain

Pascol Paving & Concrete Coatings
Semi–Transparent Concrete Stain
Data Sheet D10.63
Page 1 of 2
Resource Code 8051060
August 2012
DESCRIPTION
Pascol Semi-transparent Concrete Stain is a water based, durable acrylic finish designed to transform ordinary concrete into
an inviting space with a multi-coloured appearance that looks like natural stone. Semi-transparent Concrete Stain highlights the
natural variations and textures of concrete, brick and concrete pavers. The durable, transparent, low gloss finish provides longlasting
decorative colour, while protecting interior and exterior surfaces from water damage, household chemicals and wear
from foot traffic.
PRINCIPAL CHARACTERISTICS
Semi-transparent finish for use on: aggregate, concrete, brick, concrete pavers, flagstone, pool decks, driveways, paths and
patios.
Suitable for interior and exterior use.
This product is not recommended for use on garage floors.
COLOURS & GLOSS
Tint Base – tintable to colours in the Pascol Semi-Transparent Concrete Stain colour range
Low Gloss
BASIC DATA
Touch Dry 2 hours
Recoat 4 hours
Fully Cured 72 hours
Wait 24 hours for light (foot) traffic and 72 hours for heavy (vehicle) traffic.
All figures are quoted at 25 o C and 50% relative humidity. Drying will take longer at lower
temperatures or higher relative humidity.
Coverage per coat up to 9 M 2 /L (depending on the surface porosity and method of application)
Thinning No thinning required
Clean up Thoroughly clean equipment with water away from drains.
SURFACE PREPARATION
Do not apply over surfaces treated with water repellent sealers.
Ensure surface is clean and dry, and free from dust, dirt, oil and grease. Oil and grease should be removed with
Pascol Oil Stain Remover. All loose, peeling or flaking material must be removed. Wash all surfaces, rinse well with
clean water and allow to thoroughly dry at least overnight before painting.
Ensure all new cement and concrete surfaces are fully cured prior to painting. Typically this may take a minimum of 4
to 6 weeks. Ensure concrete surfaces are free from any bond breakers, formwork release agents and curing
compounds.
Clean, degrease and etch new or bare concrete with Pascol BOND•LOK . Refer to the BOND•LOK label for
instructions.
For previously painted or stained concrete, remove all old coating and then follow instructions for bare concrete.
APPLICATION
Stir well before and during use with a broad paddle. The product is supplied ready for use, so no thinning is required.
Do not apply when the temperature is below 10 °C or above 35 °C or when the humidity is very high. Avoid painting when
dew or rain is likely. Avoid application in direct sunlight or onto hot concrete surfaces.
Dampen concrete thoroughly with water; remove any standing water or puddles.
Use a pump sprayer set to fine-spray pattern. Apply stain to small sections (approx. 1m x 1m) at a time, spraying in a
random, circular motion. Work quickly to maintain a wet edge. Do not allow stain to “puddle” on surface
For a more uniform appearance, immediately back-roll wet areas with 10mm nap roller. Allow to dry for 4 hours before
deciding if another coat is needed. A second coat will give a darker, more uniform colour.
Optional top coat: For added protection, apply Pascol Wet Look Sealer. On driveways apply Pascol Multi-Purpose
Sealer. Refer to labels and data sheets for instructions

Pascol Paving & Concrete Coatings
Semi–Transparent Concrete Stain Data Sheet D10.63
ADDITIONAL NOTES
Page 2 of 2
Resource Code 8051060
August 2012
This Base must be tinted before use and the final volume will vary based on the selected colour. Pre-packaged colours
are ready to use and do not require tinting. If this paint has been tinted, check that the colour is suitable for your
requirements before application. For best results and colour consistency, multiple cans of tinted product should be
combined and thoroughly mixed together before starting.
The use of proprietary additives other than those manufactured by Wattyl is not recommended
SAFETY DATA
Caution Keep out of reach of children. Avoid contact with skin and eyes. Wear suitable protective
equipment. Ensure adequate ventilation during use. Avoid prolonged breathing of vapour. Wash
hands thoroughly after use.
Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Absorb spills with sand or other
inert material. Unwanted paint should be kept in a sealed container, and disposed of via special
waste collection services. Check with your local Council regarding the disposal of empty paint containers.
S.D.S. A Safety Data Sheet (S.D.S.) is available on request.
First Aid
If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre.
Phone 131126 (Australia).
If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs.
If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not
use solvents.
If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor.
ADDITIONAL DATA
3.66 L
Containers must be secured and stored upright during transit.
Containers must not be exposed to excessive heat or cold.
Leave seven days after application of final coat before washing.
Avoid exposure to excessive steam or condensation for 48 hours after application of the final coat.
For further information, contact the Wattyl Information Hotline. Phone 132101(Australia).
1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that:
(a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in
accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS;
and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product.
2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information
and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive.
3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the
information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office.
4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at
Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product.
WATTYL AUSTRALIA PTY LTD (ABN 40 000 035 914) INFORMATION HOTLINE Ph: 132101 (AUSTRALIA)