Technical Leaflet AMONN WASSERLASUR
Technical Leaflet AMONN WASSERLASUR
Technical Leaflet AMONN WASSERLASUR
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
1. Description<br />
<strong>Technical</strong> <strong>Leaflet</strong><br />
<strong>AMONN</strong> <strong>WASSERLASUR</strong><br />
Product type: <strong>AMONN</strong> <strong>WASSERLASUR</strong> is a water-based, weather-proof, protective wood stain for the<br />
protection of wood against blue stain and mould.<br />
Fields of application: For the translucent treatment of exterior wood not in permanent contact with the ground or<br />
water, such as, for example, exterior panelling, garage doors, etc.<br />
Protective action: Preventive action against blue stain and mould. <strong>AMONN</strong> <strong>WASSERLASUR</strong> regulates wood<br />
humidity and provides good protection against UV rays.<br />
Active agent: iodo-propynl butylcarbamate<br />
Colours: 0-colourless, 01-oak, 02-larch, 03-chestnut, 04-walnut, 10-light walnut, 20-spruce, 34-dark walnut<br />
Tin sizes: 25l metal tins. On request, 100 l. drums and 1.000l. containers<br />
2. <strong>Technical</strong> Data<br />
Density: 1,02 – 1,04 g/cm 3 . at +20 °C, according to the colour<br />
Flash point: >100°C<br />
Viscosity: approx. 48s/DIN 53 211, 2 mm at +20 °C<br />
Solids: content: approx. 18% according to the colour<br />
Drying time: Depending on the type of wood, the quantity applied and atmospheric conditions: after approx. 2-4<br />
hours. High air humidity and/or low temperatures can lengthen drying times.<br />
Odour: Mild, distinct odour. Odourless when dry.<br />
Storage: In original sealed tins, 1 year in a cool place, protected from frost. Close partially used tins well. If the air<br />
volume in the tin is excessive, transfer remaining product into smaller tins.<br />
3. Application<br />
Application: Stir <strong>AMONN</strong> <strong>WASSERLASUR</strong> well before use. Do not apply at temperatures below +10°C<br />
(ambient, surface and product temperature).<br />
Application methods: Brushing, impregnating machine.<br />
Preparation of the surface: The wood to be treated must be dry and free from dust and grease. Do not apply to<br />
wood with a humidity rate of over 18%. Strip old, badly adhering coats completely as these could prevent the<br />
product from penetrating into the wood. A first coat of <strong>AMONN</strong> <strong>WASSERLASUR</strong> colourless is recommended for<br />
wood with varying absorption rates. The extracts contained in certain kinds of tropical wood (e.g. iroko) can slow<br />
down the drying process; in such cases, first clean the wood carefully with a nitro-thinner.<br />
Advice for application: On large areas or highly absorbent wood, first dampen the wood with a wet sponge<br />
before commencing application. To avoid visible brush strokes, treat the whole length of the wood following the<br />
direction of the wood grain. It is necessary to increase the number of coats of <strong>AMONN</strong> <strong>WASSERLASUR</strong> on endgrain<br />
wood in order to reduce, as far possible, any water absorption. Screws, nails, hinges and other metallic<br />
parts, which may come into contact with the product, must be corrosion-resistant.<br />
Recommended cycles:<br />
New exterior wood, without dimensional<br />
stability<br />
- Renovation of exterior wood without<br />
dimensional stability<br />
2-3 x <strong>AMONN</strong> <strong>WASSERLASUR</strong> coloured, with intermediate sanding,<br />
grain 280<br />
Strip previous coats of badly adhering varnish; clean and sand the<br />
surface in order to improve adhesion, then<br />
1-2 x <strong>AMONN</strong> <strong>WASSERLASUR</strong> coloured<br />
If the wood has been completely stripped of previous coats, the<br />
recommendations for new wood should be followed.<br />
<strong>AMONN</strong> <strong>WASSERLASUR</strong> colourless contains no pigments and thus offers no protection against UV rays. It<br />
should therefore only be used on exterior wood as a finishing product in coloured cycles or for toning down darker<br />
1
colours. The effect of each single colour depends on the type of wood. It is therefore advisable to always carry<br />
out a test coat. It is furthermore recommended that the condition of the external paint is checked within 2 years of<br />
application, especially on wood exposed the weather-side (south-west), renewing the same if necessary.<br />
Yield: approx. 8-10 m²/l. per coat.<br />
Thinning: <strong>AMONN</strong> <strong>WASSERLASUR</strong> is ready for use and should not be thinned<br />
Re-coating: After approximately 4 hours, the surface can be sanded and re-coated.<br />
Cleaning of tools: immediately after use with water.<br />
4. Special advice<br />
Wood preservatives contain active biocides for the protection of wood from animal and vegetable parasites. They<br />
must be used according to the instructions and only if absolutely necessary. Misuse may cause damage to<br />
health. When using products for the protection of wood, it is necessary to follow the regulations regarding hygiene<br />
and safety in the work place and the protection of the environment (e.g. those regarding dangerous substances<br />
and inflammable liquids) paying special attention to the designation on the tin and the safety data sheet (in<br />
particular, danger symbols, danger description and indications, and safety advice). For detailed information on<br />
this argument, please consult the “Information leaflet on the use of products for wood protection” published by the<br />
German Chemical Industry Federation. Do not apply to wood which may come into direct contact with food,<br />
animal feed or drinking water. During application, protect face, hands and eyes adequately, and ensure that there<br />
is sufficient ventilation. Cover all switches and electric wires to avoid short-circuiting. Do not allow the product to<br />
come into contact with plants. Not suitable for apiaries. Read the safety data sheet carefully. Keep out of the<br />
reach of children and do not pour into the sewage system or into surface water.<br />
Water hazard class 2 (German regulation) (Self-assessment): hazardous for water<br />
Danger class according to VbF: not applicable<br />
ADR/RID: not applicable<br />
The information contained in this technical leaflet is based on recent research and technology. However, due to the extensive<br />
range of applications, we are unable to offer an unconditional guarantee for all possible applications. Please contact us for any<br />
further technical information or advice you may need.<br />
Edition 3013/3 (September 01)<br />
<strong>AMONN</strong> COLOR SrL/Gmbh – I– 39100 BOLZANO/BOZEN, Via Altmann 12 Altmannstrasse<br />
Ufficio Commerciale/Handelsbüro: Tel: 0039 0471 904770 Fax: 0039 0471 904769 E-mail: info@amonncolor.com<br />
Export: Tel: 0039 0471 904674 Fax: 0039 0471 910449 E-mail: export@amonncolor.com<br />
2