TUBE & PIPE - Tradelink

More documents

Recommendations

Info

copper tube coDeS copper tube trAdelink codes June 2010 ANNeAleD coilS coDe type A HArD DrAWN StrAigHt coDe DN6 093803 093881 DN8 093806 093886 DN10 093815 093897 polylAg ANN coil coDe polylAg HD StrAigHt coDe DN15 093824 093906 094093 094132 DN18 093837 093924 DN20 093848 093939 094364 DN25 093857 093954 DN32 093861 093966 DN40 093863 093975 DN50 093984 094162 DN65 093996 DN80 094011 DN90 DN100 094023 DN125 094025 DN150 094039 DN200 094052 ANNeAleD coilS coDe DN10 093809 type c HArD DrAWN StrAigHt coDe polylAg ANN coil coDe polylAg HD StrAigHt coDe DN15 093818 093900 094087 094126 DN18 093833 093918 094096 094135 DN20 093839 093930 094102 094141 DN25 093851 093948 094147 DN6 DN8 ANNeAleD coilS coDe type b HArD DrAWN StrAigHt coDe polylAg ANN coil coDe DN10 093812 093894 094084 polylAg HD StrAigHt coDe DN15 093821 093903 094090 094129 DN18 093836 093921 094099 094138 DN20 093842 093933 094105 094144 DN25 093854 093951 094150 DN32 093860 093963 094153 DN40 093972 094156 DN50 093981 094159 DN65 093993 094165 DN80 094008 094171 DN90 DN100 094020 094174 DN125 094024 DN150 094037 DN200 094051 type D HArD DrAWN StrAigHt coDe DN32 093960 DN40 093969 DN50 093978 DN65 093990 polylAg HD StrAigHt coDe DN80 094005 094168 DN90 DN100 094017 094177 DN125 codes for lArge diAmeter copper tube not in the As 1432 rAnge DN150 094036 extrapolating from AS 1432 the following DN250 copper tube is approximately equivalent to a type b. Nom. Size mill Size mm leNgtHS - m 4.0 4.5 5.0 5.5 DN250 10” x 12G 094094 094095 094097 094098 tube & pipe copper tube coDeS 15.5
tube & pipe copper tube for AircoNDitioNiNg & refrigerAtioN 15.6 copper tube For AircoNDitioNiNG & reFriGerAtioN An extensive range of copper tube is manufactured specifically to cater for the special requirements of refrigeration gas lines and airconditioning. these tubes comply with the required internal cleanness limits specified in AS 1571:copper - Seamless tubes for Airconditioning and refrigeration. tubes are factory cleaned and supplied sealed to maintain the cleanness of the bore under normal conditions of handling and storage. ink mArking the tube is identified with an ink marking along its length stating the Manufacturers Name, country of origin, conforming standard, temper and Size. eg. “crANe copper tube AuStrALiA AS/NZS 1571 1/2h 19.05 X 0.91” pAckAging As drawn straight length tubes are capped on each end and packaged in bundles. Annealed coils are encapsulated with heat shrunk plastic. caps are included for placement on tube after the plastic is removed. the capping for airconditioning and refrigeration grade tubing is colour coded yellow. mAnufActuring stAndArds AVAilAble code American copper Alloy no. chemical requirement AStM b280 Australian uNS. c12200 cu 99.9% min. po.015-0.40% AS1571 c122 cu 99.9% min. po.015% min. 0.040% max. cleAnness requirements All tubes are cleaned and sample tested to meet the residue requirement as specified by the codes at 0.038 g/m3 (0.0035g/m 2). tube integrity All tubes are electronically tested by eddy current method, to the requirements of AStM e243. positiVe pressure lines As drawn copper tube to AS 1571 is permitted, with dimensions as specified in AS 1432 type b. For nominal sizes DN 15 and below, the thickness shall not be less than 1.02mm. VAcuum lines Sizes are the same as for positive pressure lines but either as drawn or annealed temper tubes may be used. note: AS 1571 tube is unavailable, tube must be cleaned as specified in AS 2896. medicAl gAses grAde copper tubes interpolation of allowable design stress as defined by table d7 of As4041 for the below temperatures. Safety standards for oxygen and other medical gases require the use of specially cleaned tubing in order to prevent gas contamination, or potential explosions. oxygen under pressure may cause spontaneous combustion of residual organic drawing oils, if left inside tubes after manufacture. Similarly, oils or other contaminants could cause severe patient problems if not removed prior to installation. crane enfield Metals are able to provide a wide range of tubes to several international standards for this highly sensitive work. code no. code description Australian AS2896 Medical gas systems - installation and testing of non-inflammable medical gas pipeline systems. Australian AS1169 installation and testing of medical gas supply systems. American AStMb819 Medical gas systems tubing. Although tubes are supplied specially cleaned and capped ready for use, it is the duty of the installer that all regulations covering installation practices are complied with. particular attention should be given to: 1. Storage and handling. 2. Site cleaning of tubes and components. 3. pipeline gas purging during brazing. 4. use of approved filler metals and fluxes. 5. post brazing cleaning and visual inspection of all joints. 6. Full compliance with pressure and containment testing before final approval and use. the methods used by crane enfield Metals for the cleaning and capping of medical grade copper tubing is a documented procedure under Quality Systems Standards AS3902-1987ASo 9002:1987, as covered by Licence No. 0590. the capping for Medical grade tubing is colour coded green and the ink marking includes “MeDicAL GAS”. r410A rAted tube the r410A rated copper tube is especially designed to comply with AS4041 pressure piping code. our r410A rated copper tube is capable of withstanding working pressures of 4121 kpa when the refrigerant is operating at a temperature of 65°c, which is the recommended operating temperature as per AS/NZS 1677 refrigeration systems. the r410A rated copper tube is distinguished by rose colour capping and “r410A rAteD” becomes part of the ink marking. key for table page 15.07 pSW = 2,000 x SD x tm D – tm SD = Maximum allowable design stress for annealed copper in mega pascals tm = Minimum thickness any point (mm) D = Maximum mean outside diameter (mm) *Safe working pressures calculated for annealed copper. temperAture (°c) 50.0 55.0 60.0 65.0 70.0 75.0 SD (mpa) 41 38.6 36.83 35.55 34.63 34 the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.
Page 1 and 2: tube & pipe copper tuBe 15.1 polyla
Page 3 and 4: tube & pipe copper tube polylAg 15.
Page 5: tube & pipe copper tube Selector iN
Page 9 and 10: tube & pipe Steel pipeS to AS1074 1
Page 11 and 12: tube & pipe Steel pipeS to ANSi b36
Page 13 and 14: tube & pipe StAiNleSS Steel pipe 15
Page 15 and 16: tube & pipe StAiNleSS Steel tube 15
Page 17 and 18: tube & pipe StAiNleSS Steel tube 15
Page 19: tube & pipe permApipe 15.18 perMApi

TUBE & PIPE - Tradelink

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?