Fitting Instructions - Wickes
Fitting Instructions - Wickes
Fitting Instructions - Wickes
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CONTENTS<br />
HEALTH & SAFETY GUIDELINES 2<br />
GENERAL PRODUCT INFORMATION 3<br />
CONTENTS 3<br />
TOOLS FOR THE JOB 3<br />
INSTALLATION INSTRUCTIONS 3<br />
FITTING/REPLACING THE BULB 4<br />
CARE & CLEANING 4<br />
CUSTOMER SUPPORT 4<br />
HEALTH & SAFETY GUIDELINES<br />
CAUTION<br />
Read all safety instructions carefully. Failure to comply<br />
with the following safety instructions may cause<br />
electric shock, fire and/or serious injury.<br />
ELECTRICAL SAFETY<br />
All fittings must be installed in accordance with the<br />
current edition of the IEE Wiring regulations (BS7671:<br />
Requirements for Electrical Installations), Part P of<br />
the Building Regulations and appropriate statutory<br />
regulations. If in doubt, consult a qualified electrician.<br />
Before commencing any work ensure the supply is<br />
switched off at the mains. Either by switching off<br />
main switch at the consumer unit or by removing the<br />
appropriate fuse.<br />
As from April 2004 twin and earth wiring colours<br />
changed;<br />
EARTH Green/yellow sleeving<br />
LIVE Brown replaces red<br />
NEUTRAL Blue replaces black<br />
To prevent a fire hazard always use the cable of correct<br />
rating, size and type for application.<br />
Ensure all terminal screws are tight and all wires are<br />
neatly routed and not unduly stretched or pinched.<br />
All earth connections must be made and continuity<br />
maintained.<br />
Where any earth conductor is a bare wire, it must be<br />
sleeved with green/yellow sleeving.<br />
If connecting to a switch, the switched live conductor<br />
must be appropriately identified.<br />
If drilling new holes, be sure to locate cables before<br />
beginning work, to avoid electric shock and damage to<br />
existing circuits.<br />
GENERAL SAFETY<br />
When working at heights, make sure you are using the<br />
correct equipment and follow all safety instructions.<br />
Make sure that your workplace is tidy, clear from<br />
debris, well lit and dry.<br />
GENERAL PRODUCT INFORMATION<br />
IP65<br />
IP65<br />
CONTENTS<br />
LAMP TYPE &<br />
MAX.<br />
WATTAGE<br />
– LINKING LED lights<br />
– LED driver<br />
– Instruction manual (retain for future reference)<br />
TOOLS FOR THE JOB<br />
S15<br />
MAX 60W<br />
– 2mm slotted screwdriver or electrical screwdriver<br />
– Hole saw or Forstener bit<br />
INSTALLATION INSTRUCTIONS<br />
This LED lighting kit is designed for outdoors installation<br />
for use in patios, in walls, on decking, step edges, in<br />
pathways and in other areas of the garden.<br />
This system operates at Safety Extra Low<br />
Voltage (12V), via the plug-in driver. Never III<br />
connect the light fittings directly to the mains<br />
without using this driver.<br />
Always unplug the driver from the mains when installing<br />
or maintaining this system.<br />
Layout:<br />
Plan the desired layout of these fittings carefully, ensuring<br />
the cables will reach the distances between the<br />
driver, and each light fitting.<br />
Avoid locating any cables in positions that would cause<br />
a trip hazard. Position cables away from areas where<br />
they may be at risk from being cut, trapped or damaged.<br />
The 3 pin plug has no special protection against moisture<br />
and must be situated indoors or in a suitable IP65 outdoor<br />
socket box.<br />
The driver is rated at IP65 and can be positioned outdoors.<br />
Each connector is rated at IP65 (when rubber o-ring is in<br />
position) and can be positioned outdoors.<br />
The light units are rated at IP65.<br />
PARTS MISSING?<br />
Contact the customer service helpline number and<br />
quote <strong>Wickes</strong> 218846/218847/218850/218853/218854<br />
Installation:<br />
1) Do not plug-in at this stage.<br />
2) After deciding the layout of the light fittings,<br />
ensure the cables are long enough to connect to the<br />
desired positions. Each head links to the next via the<br />
IP65 connector. Additional heads can be purchased<br />
separately. <strong>Wickes</strong> Codes 218848/ 218849. Refer to<br />
product packaging for maximum number of heads<br />
permissible for the supplied driver.<br />
3) Drill the mounting holes for the light units taking care<br />
not to damage any pipes or mains cables beneath the<br />
mounting surface. For 30mm diameter LED lights drill<br />
a 22mm clearance hole. For 45mm LED drill a 32mm<br />
clearance hole. Minimum hole depth is 30mm.<br />
4) Feed the plug and cable of each light unit through the<br />
mounting holes and push unit into the hole to secure.<br />
5) Connect each head to the next in series. See layout<br />
diagram overleaf.<br />
6) Use the supplied blanking plug to cover last sockets<br />
which are not being used, to prevent water ingress.<br />
7) Connect the driver cable into the end socket.<br />
8) Plug the driver into the mains socket and switch on.
Indoor Plug<br />
LED driver<br />
(Outdoor IP67)<br />
FITTING/REPLACING THE BULB<br />
This fitting uses non replaceable LEDs and needs no user maintenance.<br />
CARE & CLEANING<br />
FINISH<br />
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish.<br />
Waste electrical products should not be disposed of with normal household waste. Please recycle where facilities exist.<br />
Check with your Local Authority or retailer for recycling advice.<br />
CUSTOMER SUPPORT<br />
5m<br />
2 core DC cable<br />
Connect heads in series one to the next<br />
1 x end cap<br />
CUSTOMER SUPPORT<br />
Product Helpline (01202) 690945. Mon-Thur 9am-5pm, Fri 9am-1pm.<br />
We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts<br />
be damaged or missing please contact our Product Helpline. This will save you the inconvenience of re-packing and<br />
returning the product to the store where purchased. Simply phone the number above and we will despatch to you,<br />
within 7 working days, your missing/damaged part. When phoning please ensure you have the following information<br />
available. Name and Address, Daytime Telephone Number, Store and Date of Purchase, Product Reference (inside<br />
ceiling cover or on box label), Description of Missing/Damaged Part. This does not affect your statutory rights.<br />
ADDITIONAL SERVICES<br />
If you require replacement parts these can be despatched for a charge by telephoning the Product Helpline number above.<br />
<strong>Wickes</strong>, Lodge Way House, Lodge Way, Harlestone Road, Northampton, NN5 7UG<br />
www.wickes.co.uk<br />
LED DECKLIGHT<br />
KIT<br />
INSTRUCTION MANUAL