OPERATION MANUAL

Specifications Section 1-2
Output terminal (service
supply)
RUN output
(See note 2.)
Item Specification
Provided only on the PA204S. (See note 4.)
0.3 A or less current consumption by 24-V DC
load: 24 V DC is +17% to −11%
0.3 A current consumption by 24 V DC load:
24 V DC is +10% to −11% (lot No. 0197 or later)
Provided only on the PA204S. (See note 5.)
Contact form: SPST-NO
Switching capacity:
250 V AC, 2 A (resistive load)
250 V AC, 0.5 A (induction load: 24 V DC, 2 A)
None
Contact configuration: SPST-NO
Switch capacity: 240 V AC, 2A (resistive load),
120 V AC, 0.5 A (induction load)
24 V DC, 2A (resistive load)
24 V DC, 2 A (induction load)
Insulation resistance 20 MW min. (at 500 V DC) between AC external and GR terminals (See note 1.)
Dielectric strength 2,300 V AC 50/60 Hz for 1 min between AC external and GR terminals (See note 1.)
Leakage current: 10 mA max.
1,000 V AC 50/60 Hz for 1 min between DC external and GR terminals (See note 1.)
Leakage current: 10 mA max.
Noise immunity 2 kV on power supply line (conforming to IEC61000-4-4)
Vibration resistance 10 to 57 Hz, 0.075-mm amplitude, 57 to 150 Hz, acceleration: 9.8 m/s2 in X, Y, and Z directions for
80 minutes (Time coefficient: 8 minutes × coefficient factor 10 = total time 80 min.) CPU Unit
mounted to a DIN track: 2 to 55 Hz, 2.94 m/s2 in X, Y, and Z directions for 20 minutes
Shock resistance 147 m/s 2 3 times each in X, Y, and Z directions (according to JIS C0041)
Ambient operating 0 to 55°C
temperature
Ambient operating 10% to 90% (with no condensation)
humidity
Atmosphere Must be free from corrosive gases.
Ambient storage −20 to 75°C (excluding battery)
temperature
Grounding Less than 100 Ω
Enclosure Mounted in a panel.
Weight Refer to Section 3.
CPU Rack dimen- 2-slot Rack: 198.5 ×157×123 mm (W×H×D) (See note 3.)
sions (mm)
3-slot Rack: 260 × 130 × 123 mm (W×H×D) (See note 3.)
5-slot Rack: 330 × 130 × 123 mm (W×H×D) (See note 3.)
8-slot Rack: 435 × 130 × 123 mm (W×H×D) (See note 3.)
10-slot Rack: 505 × 130 × 123 mm (W×H×D) (See note 3.)
Safety standards Conforms to cULus and EC Directives.
Note (1) Disconnect the Power Supply Unit's LG terminal from the GR terminal
when testing insulation and dielectric strength. Testing the insulation and
dielectric strength with the LG terminal and the GR terminals connected
will damage internal circuits in the CPU Unit.
(2) Supported only when mounted to CPU Backplane.
(3) The depth is 153 mm for the C200HW-PA209R Power Supply Unit.
(4) The C200HW-PA204 and C200HW-PA204R do not have an output terminal.
(5) The C200HW-PA204 and C200HW-PA204S do not have a RUN output.
17