Introduction to PhotoKit Color 2.0 - Pixel Genius

More documents

Recommendations

Info

Nocturnal effect With the Nocturnal effect you can take a normal daylight photograph and give it the appearance of a night time shot. In the example shown below you can see the Nocturnal effect applied using the default settings to a picture that was shot at midday under cloudy lighting conditions.
Note: Roll your mouse cursor over the image to see the indicated PhotoKit Color effect. Nocturnal effect layers The Nocturnal effect attempts to create a night time look by filtering the image in two ways. The Luminosity layer aims to match the color sensitivity of human vision under low light levels and at the same time make the image darker. The default opacity is set to 90%, but you can adjust this if you wish. If you rollover the layers palette on the right, you can see how the same image would look with the luminosity layer set to 55%. The Color layer is set to Color blend mode at 25% and this layer applies a blue tint to the image. If you would like to have a more neutral looking night image, then try reducing the opacity of this layer.
Page 1 and 2:
Introduction to PhotoKit Color 2.0
Page 3 and 4:
PhotoKit Color basics For a quick i
Page 5 and 6:
PhotoKit Color Effects The PhotoKit
Page 7 and 8:
Merge Results The layers produced b
Page 9 and 10:
PhotoKit Color 2.0 Sets & Effects L
Page 11 and 12:
Burn Tone The Burn Tone series has
Page 13 and 14:
Installing PhotoKit Color 2.0 Photo
Page 15 and 16:
After unzipping, you will find a si
Page 17 and 18:
After the search, the installer wil
Page 19 and 20:
Installing PhotoKit Color on Macint
Page 22 and 23: The following warning informs you t
Page 24 and 25: If you receive the above dialog box
Page 26 and 27: Launching PhotoKit Color the First
Page 28 and 29: Buying PhotoKit Color 2.0 from the
Page 30 and 31: When filling out the 'Personal Info
Page 32 and 33: Opening PhotoKit Color 2.0 After in
Page 34 and 35: The PhotoKit Color 2 dialog When yo
Page 36 and 37: It's useful to remember that PhotoK
Page 38 and 39: image is in Grayscale, Lab or CMYK
Page 40 and 41: From: PhotoKit Color User Guide htt
Page 42 and 43: In the example shown here, I began
Page 44 and 45: Film Effects
Page 46: RGB Workspaces The above film effec
Page 49 and 50: Note: Roll your mouse cursor over t
Page 52 and 53: Simulating film cross process effec
Page 56: Note: Roll your mouse cursor over t
Page 75 and 76: Dodge
Page 77 and 78: If you want a stronger Dodge effect
Page 81 and 82: Color Enhance Blue Enhance | Green
Page 83 and 84: Blue Darken Blue Darken + Mask
Page 85 and 86: ers. The lower layer contains the m
Page 87 and 88: Top | Blue Enhance | Green Enhance
Page 89 and 90: Red Lighten Red Lighten + Mask
Page 91 and 92: the default 50% opacity. Above this
Page 97 and 98: CC Correction
Page 99: RGB Workspaces The above film effec
Page 104 and 105: The reason for this happening is du
Page 106 and 107: RSA Gray Balance is designed to han
Page 108 and 109: PhotoKit Color 2.0: Saving Images O
Page 110 and 111: Because Photoshop tries to prevent
Page 112 and 113: Saving a copy of the original At th
Page 114 and 115: Summary To recap, running a PhotoKi
Page 116 and 117: can only install properly when a U.
Page 118: Information about Pixel Genius,LLC.
show all

Introduction to PhotoKit Color 2.0 - Pixel Genius

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?