HMI Tools English Svenska - Omni Ray AG

More documents

Recommendations

Info

System Loader Mark Overwrite PLC driver if the driver in the terminal should be erased at the transfer. The driver is not erased if it is unmarked. Select Send to start the transfer. Note! When downgrading a terminal it is important to make sure that the square “Overwrite PLC driver” is marked” 4.1 Communication settings The personal computer Under Options/Comm Settings you make the settings for the transfer parameters. Port Select communication port for the personal computer. Baud Select baudrate. TimeOut Timeout for the communication. The value is stated in milliseconds. Using modem Mark if you are using modem connection. Used with latest terminal version and higher transfer speed than 2 400 baud. 13
System Loader 14 The terminal If the transfer does not start, the terminal must manually be set in sysload mode. For further information see the manual for the terminal. Note! The personal computer must be connected to a serial port on the terminal, serial or via a modem. Start loading When the terminal and the personal computer are connected and the transfer parameters are correctly set the system program can be loaded to the terminal. Select Send. The status parameters for the transfer are shown in the status window. 4.2 Start the program via command line You can start the program from the command line. This makes it possible to start the program from another application, e.g. the SCADA system FactoryLink. You can enter the following commands on the command line: sysload filename or sysload filename baud port where filename Name of the *.bin file to send to the terminal baud The baudrate for the transfer port communication port number (COMx) Example: sysload E700v600.bin 9600 1
Page 1 and 2: HMI Tools English Svenska © Beijer
Page 4 and 5: Content 1 Introduction ............
Page 6 and 7: 1 Introduction Introduction HMI Too
Page 8 and 9: 3 File Transfer File Transfer The p
Page 10 and 11: File Transfer Click on the + charac
Page 12 and 13: Format 2 File Transfer Format 2 is
Page 14 and 15: 3.4 Communication settings File Tra
Page 16 and 17: 3.5 Start the program via the comma
Page 20 and 21: 5 Connect The program HMI Tools Con
Page 22 and 23: Baud Select baudrate. Parity Select
Page 24 and 25: 6 FTP Client FTP Client HMI Tools F
Page 26 and 27: 6.2 Transfer files to the terminal
Page 28 and 29: Editing recipe A text for the recip
Page 30 and 31: FTP Client Press the New button to
Page 32: Manual, HMI Tools Förord Denna man
Page 35 and 36: II Innehåll
Page 37 and 38: 2 Installation 2 Installation HMI T
Page 39 and 40: 4 File Transfer 3.1 Överföra file
Page 41 and 42: 6 File Transfer Funktioner Delete R
Page 43 and 44: 8 File Transfer Klicka med höger m
Page 45 and 46: File Transfer 10 Baud Välj överf
Page 47 and 48: System Loader 12 4 System Loader Pr
Page 49 and 50: System Loader 14 Terminal Om överf
Page 51 and 52: Connect 16 5.1 Definiera telefonans
Page 53 and 54: Connect 18 Autostop timeout (s) - A
Page 55 and 56: FTP Client 20 6.1 Överföra filer
Page 57 and 58: FTP Client 22 Format 1 Format 1 anv
Page 59 and 60: FTP Client 24 Klicka med höger mus
Page 61: FTP Client 26 Name Skriv in ett val

HMI Tools English Svenska - Omni Ray AG

Create successful ePaper yourself

Delete template?

Save as template?