Assignments - Georgia Northwestern Technical College

Fall 2013
Assignments
DFTG 1113, Technical Drawing V
As a student at Georgia Northwestern Technical College, you are required to maintain a
positive level of work ethics. By practicing work ethics everyday in the classroom, you
are preparing for the skills needed to be a successful employee. Because of these
occupational and work habits, the lab will be treated like a work environment. You will
be evaluated on your demonstration on the following work ethic categories. Each week
you will focus on the given topic as you build habits from the previous week. Weeks 11-
15 will allow for reflection and practice of all work ethics skills covered in the term.
Week
1
Attendance
Week
2
Character
Week
3
Teamwork
Week
4
Appearance
Week
5
Attitude
Week
6 Productivity
Week
7
Week
8
Week
9
Week
10
Organizational Skills
Communication
Cooperation
Respect
Attends class; arrives/leaves on time; notifies instructor in advance of
planned absences
Displays loyalty, honesty, trustworthiness, dependability, reliability,
initiative, self-discipline, and responsibility.
Respects the rights of others; displays teamwork, is cooperative and
assertive, and displays a customer service attitude.
Displays appropriate dress, grooming, hygiene, and etiquette.
Demonstrates a positive attitude, appears self-confident; has realistic
expectations of self.
Follows Safety practices; conserves materials; keeps work area neat
and clean; follows directions and procedures; makes up assignments
punctually; participates.
Manifests skill in prioritizing and management of time and stress;
demonstrated flexibility in handling change.
Displays appropriate nonverbal and oral listening skills.
Displays leadership skills; appropriately handles criticism, conflicts,
and complaints; demonstrates problem-solving capability; maintains
appropriate relationships with supervisor and peers; follows chain of
command.
Deals appropriately with cultural/racial diversity; does not engage in
harassment of any kind
Assignments
The assignments listed below must be submitted in a timely manner.
Assignments must be submitted for grading every week in order to get the
necessary feedback from the instructor that will help the student learn from
potential mistakes. Assignments will not be accepted on the last day of class
without penalty.

Module 1:
1. Power Point Presentation: See Resources section of
Drafting Webpage.
2. Reading Assignment: (Technical Drawing 14th Edition)
Read Chapter 13, Working Drawings.
*If you are using the 13th Edition of this text, then read
Chapter 12, Working Drawings.
3. Lab Application No. 1: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.38, Tool Post. This should
be completed as a Detail Drawing.
*If you are using the 13th Edition of this text , then Chapter
12, Exercise 12.38, Tool Post.
Directions: Review rules for simplified drafting from chapter.
Draw problem as a detail drawing and include all necessary
views, finish marks, dimensions and notes. Plot drawing and
have the instructor check your work when complete.
4. Work Ethics Attendance Test: Angel Test
5. Work Ethics Character Test: Angel Test
Instructor Check: Detail drawing, Piece Marks, Selection Of Views,
Scale, Drawing Numbers, Bill Of Material, Simplified Drafting.
Module 2:
1. Lab Application No. 2: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.38, Tool Post. This should
be completed as an Assembly Drawing.
*If you are using the 13th Edition of this text , then Chapter
12, Figure 12.38, Tool Post.
Directions: Draw an Orthographic Assembly Drawing of the
Tool Post; include a "Bill Of Materials". Review rules for
assembly drawing and assembly sectioning from chapter.

Plot drawing and have the instructor check your work when
complete.
2. Work Ethics Teamwork Test: Angel Test
3. Work Ethics Appearance Test: Angel Test
Resource for reference: (Technical Drawing 14th Edition) Chapter 13,
Working Drawings
Module 3:
1. Lab Application No. 3: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.39, Belt Tightener. This
should be completed as a Detail Drawing.
*If you are using the 13th Edition of this text , then Chapter
12, Figure 12.39, Belt Tightener
Directions: See assigned tolerances at the bottom of the
page. Calculate all tolerances for specified fits. Review rules
for simplified drafting from chapter. Draw problem as a detail
drawing and include all necessary views, finish marks,
dimensions and notes. Plot drawing and have the instructor
check your work when complete.
2. Work Ethics Attitude Test: Angel Test
3. Work Ethics Productivity Test: Angel Test
o Works Ethics: See Instructor
Module 4:

1. Lab Application No. 4: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.39, Belt Tightener. This
should be completed as an Assembly Drawing.
*If you are using the 13th Edition of this text , then Chapter
12, Figure 12.39, Belt Tightener
Directions: Draw an Orthographic Assembly Drawing of the
Belt Pulley; include a "Bill Of Materials". Review rules for
assembly drawing and assembly sectioning from chapter.
Plot drawing and have the instructor check your work when
complete.
2. Work Ethics Organizational Skills Test: Angel Test
3. Work Ethics Communication Test: Angel Test
Module 5:
1. Lab Application No. 5: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.51, Machine Vise. This
should be completed as a Detail Drawing.
*If you are using the 13th Edition of this text , then Chapter
12, Figure 12.51, Machine Vise.
Directions: Review rules for simplified drafting from chapter.
Draw problem as a detail drawing and include all necessary
views, finish marks, dimensions and notes. Use the
Machinery Handbook and related reference material for
specifications if necessary. Plot drawing and have the
instructor check your work when complete.
2. Work Ethics Cooperation Test: Angel Test
Module 6:
1. Lab Application No. 6: (Technical Drawing 14th
Edition) Chapter 13, Exercise 13.51, Machine Vise. This
should be completed as an Assembly Drawing.

*If you are using the 13th Edition of this text , then Chapter
12, Figure 12.51, Machine Vise.
Directions: Make a Pictorial Assembly Drawing of the
Machine Vise. Include a "Bill Of Materials" and use the
Machinery Handbook and related reference material for
specifications. Plot drawing and have the instructor check
your work when complete.
2. Work Ethics Legal_Ethical Issues Test: Angel Test
Final Exam
o Instructor Check: Pictorial Assembly
o Work Ethics: See the instructor