CFD-E75L - diagramas.diagram...

CFD-E75L
SERVICE MANUAL
Ver 1.0 2001.05
AEP Model
UK Model
Photo: White model
CD
Section
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
CFD-926L
KSM-213CDP
KSS-213C
TAPE Model Name Using Similar Mechanism CFD-926L
Section Tape Transport Mechanism Type MF-V5-117
SPECIFICATIONS
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +0/–1 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM 87.5 - 108 MHz
MW
LW
531 - 1 602 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
153 - 279 kHz
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 8 cm (3 1 ⁄4 in.) dia.,
4 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 64 Ω impedance headphones
Maximum power output
4 W
Power requirements
For CD radio cassette-corder:
230 V AC, 50 Hz
9 V DC, 6 R14 (size C) batteries
For memory back-up:
4.5 V DC, 3 R6 (size AA) batteries
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 14 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 5 h
Sony alkaline LR14: approx. 20.5 h
Tape playback
Sony R14P: approx. 6 h
Sony alkaline LR14: approx. 27 h
CD playback
Sony R14P: approx. 1.5 h
Sony alkaline LR14: approx. 8 h
Dimensions
Approx. 283 × 165 × 281 mm (w/h/d)
(11 1 ⁄4 × 6 1 ⁄2 × 11 1 ⁄8 inches) (incl. projecting parts)
Mass
Approx. 3.5 kg (7 lb. 11 oz) (incl. batteries)
Supplied accessories
Mains lead (1)
Remote control (1)
Design and specifications are subject to change without
notice.
IF
FM: 10.7 MHz
MW/LW: 450 kHz
Aerials
FM: Telescopic aerial
MW/LW: Built-in ferrite bar aerial
CD RADIO CASSETTE-CORDER
9-873-127-11 Sony Corporation
2001E0500-1 Personal Audio Company
C 2001.5
Shinagawa Tec Service Manual Production Group

CFD-E75L
TABLE OF CONTENTS
1. SERVICING NOTES .............................................. 3
2. GENERAL .................................................................. 4
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 7
3-2. Cabinet Lower Assy ........................................................ 7
3-3. AC INLET Board, Power Board ..................................... 8
3-4. TUNER Board, MAIN Board ......................................... 8
3-5. Cover Plate Assy ............................................................. 9
3-6. CD Mechanism Deck (KSM-213CDP) .......................... 9
3-7. Optical Pick-up (KSS-213C) .......................................... 10
3-8. Cabinet Front Assy .......................................................... 10
3-9. Tape Mechanism Deck (MF-V5-117) ............................ 11
3-10. CD Lid ............................................................................. 11
3-11. Lid Cassette Assy, LCD Board ....................................... 12
3-12. Head (HRP301), Motor Assy (M301), Belt ................... 12
3-13. Connector Setting ............................................................ 13
4. MECHANICAL ADJUSTMENTS ...................... 14
5. ELECTRICAL ADJUSTMENTS
Tape Deck Section ......................................................... 14
Tuner Section ................................................................. 15
CD Section ..................................................................... 17
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
This Compact Disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is located
at the rear.
6. DIAGRAMS
6-1. Block Diagram – CD Section – .................................... 19
6-2 Block Diagram – TUNER Section – ............................ 20
6-3. Block Diagram – MAIN Section – ............................... 21
6-4. Block Diagram – POWER SUPPLY Section – ............ 22
6-5. Printed Wiring Board – CD Section – .......................... 24
6-6. Schematic Diagram – CD Section – ............................. 25
6-7. Printed Wiring Board – TUNER Section – .................. 26
6-8. Schematic Diagram – TUNER Section – ..................... 27
6-9. Printed Wiring Board – TAPE DECK Section – .......... 28
6-10. Schematic Diagram – TAPE DECK Section – ............. 28
6-11. Printed Wiring Boards – MAIN/LCD Boards – ........... 29
6-12. Schematic Diagram – MAIN Board (1/2) – ................. 30
6-13. Schematic Diagram – MAIN (2/2)/LCD Boards – ...... 31
6-14. Printed Wiring Boards – PANEL Section – ................. 32
6-15. Schematic Diagram – PANEL Section – ...................... 33
6-16. Printed Wiring Boards
– POWER SUPPLY Section – ....................................... 34
6-17. Schematic Diagram
– POWER SUPPLY Section – ....................................... 35
6-18. IC Pin Function Description .......................................... 38
7. EXPLODED VIEWS
7-1. Cabinet Section ............................................................... 40
7-2. Cabinet Upper Section .................................................... 41
7-3. Cabinet Front Section ..................................................... 42
7-4. Cabinet Lower Section .................................................... 43
7-5. Optical Pick-up Section (KSM-213CDP) ...................... 44
7-6. Tape Mechanism Deck Section-1 (MF-V5-117) ............ 45
7-7. Tape Mechanism Deck Section-2 (MF-V5-117) ............ 46
8. ELECTRICAL PARTS LIST .............................. 47 SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
2

SECTION 1
SERVICING NOTES
CFD-E75L
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Turn POWER switch on with no disc inserted and make Function
switch to CD position.
2. Open the lid for CD.
3. Turn on S901 as following figure.
4. Press the [ u] (CD) button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit
or Optical Pick-up is broken.
Objective lens moves up and down three times for the focus
search.
S901
3

CFD-E75L
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Basic Operations
Playing a CD
3
1, 2
Use these buttons for additional operations
Jog dial
ZPUSH
OPEN/CLOSE
x
VOLUME +, –
u
Basic Operations
OPERATE
Connect the supplied mains lead (see page 24).
1 Press ZPUSH OPEN/CLOSE down
to open the CD compartment and
place the CD on the CD
PUSH OPEN/CLOSE compartment.
With the label side up
2 Close the lid of the CD compartment.
PUSH OPEN/CLOSE
3 Press u (N on the remote).
The player turns on (direct power-on)
and plays all the tracks once.
Display
Track number Playing time
To
Do this
adjust the volume
Press VOLUME +, – (VOL +, – on
the remote).
stop playback Press x.
pause playback
go to the next track
go back to the previous track
remove the CD
turn on/off the player
Press u (X on the remote).
Press the button again to resume
play after pause.
Turn the jog dial clockwise.
(On the remote, press >.)
Turn the jog dial counterclockwise.
(On the remote, press ..)
Press ZPUSH OPEN/CLOSE.
Press OPERATE
About CD-Rs/CD-RWs
This player is compatible with CD-Rs/CD-RWs but
playback capability may vary depending on the quality of
the disc, the recording device and application software.
5 GB
Listening to the radio
1 2
RADIO
BAND
AUTO PRESET
6 GB
Connect the supplied mains lead (see page 24).
1 Press RADIO BAND•AUTO
PRESET until the band you want
appears in the display (direct poweron).
Each time you press the button, the
band changes as follows:
“FM” t “MW” t “LW”
2 Hold down TUNE + or – until the
frequency digits begin to change in
the display.
The player automatically scans the
radio frequencies and stops when it
finds a clear station.
If you can't tune in a station, press
the button repeatedly to change the
frequency step by step.
TUNE
Display
Indicates an FM stereo
broadcast
Tips
• If the FM broadcast is
noisy, press MODE until
“Mono” appears in the
display and the radio will
play in monaural.
• If you need to change the
AM/MW tuning interval,
see page 25.
Use these buttons for additional operations
To
Press
adjust the volume VOLUME +, –
(VOL +, – on the remote)
turn on/off the radio
OPERATE
To improve broadcast reception
Reorient the aerial for FM. Reorient the player itself for
AM or MW/LW.
for FM
OPERATE
MODE
VOLUME +, –
for MW/LW
Basic Operations
7 GB
4

CFD-E75L
8 GB Playing a tape
Connect the supplied mains lead (see page 24).
1 Press xZ to open the tape
With the side you want
compartment and insert a recorded to play facing you
tape. Use TYPE I (normal) tape only.
Close the compartment.
2 Press n.
Display
The player turns on (direct power-on)
and starts playing.
1
2
Use these buttons for additional operations
To
Press
adjust the volume VOLUME +, –
(VOL +, – on the remote)
stop playback
fast-forward or rewind the tape
pause playback
eject the cassette
turn on/off the player
xZ
m or M
X
Press the button again to
resume play after pause.
xZ
OPERATE
VOLUME +, –
m, M
xZ
X
OPERATE
Basic Operations
9 GB
Recording on a tape
1
RADIO
BAND
AUTO PRESET
10 GB
Connect the supplied mains lead (see page 24).
1 Press xZ to open the tape
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
2 Select the programme source you
want to record.
3
To record from the CD player, insert
a CD (see page 4) and press x on the
CD section.
To record from the radio, tune in the
station you want (see page 6).
With the side you want to
record on facing you
Display
3 Press z to start recording
(n is depressed automatically).
Tips
• Adjusting the volume or the
audio emphasis (see page
18) will not affect the
recording level.
• If the AM/MW/LW
programme makes a
whistling sound after you've
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that most decreases
the noise.
• For the best results, use the
AC power as a power
source.
• To erase a recording,
proceed as follows:
1 Insert the tape whose
recording you want to
erase.
2 Press X.
3 Press n.
4 Press z.
5 Press X.
Use these buttons for additional operations
To
stop recording
pause recording
turn on/off the player
Press
xZ
OPERATE
MODE
n
xZ
X
X
Press the button again to resume
recording.
OPERATE
Basic Operations
11 GB
5

CFD-E75L
The Timer
Setting the clock
“– –:– –” indication appears in the display
until you set the clock.
MENU
ALARM
Jog dial
DSPL
ENT MEM
3 Press DSPL•ENT MEM.
The clock starts from 00 seconds.
Tip
The time display system:
24-hour system
The Timer
Before you set the clock, connect the power
source (see page 24).
1 Press MENU•ALARM until “CLOCK”
appears in the display, then press
DSPL•ENT MEM.
The hour digit flashes.
2 Turn the jog dial to set the current hour.
Then press DSPL•ENT MEM.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
19 GB
6

SECTION 3
DISASSEMBLY
CFD-E75L
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Set
Cabinet lower assy
AC INLET board, POWER board
TUNER board, MAIN board
Cover plate assy
Cabinet front assy
CD lid
CD mechanism deck
(KSM-213CDP)
Tape mechanism deck
(MF-V5-117)
Optical pick-up
(KSS-213C)
Lid cassette assy,
LCD board
Head (HRP301),
motor assy (M301), belt
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET LOWER ASSY
4 screw
(BVTP3 × 14)
3
4 two screws
(BVTP3 × 14)
6 connector
(CN322)
7 connector
(CNP392)
5
8 cabinet lower assy
2 four screws
(BVTP3 × 10)
1 two screws
(BVTP3 × 14)
7

CFD-E75L
3-3. AC INLET BOARD, POWER BOARD
5 two screws
(BVTP3 × 10)
3 AC INLET board
2 two screws
(BVTP3 × 10)
6 plate shield (TRANS)
4 connector
(CNP901)
1 connector
(CN902)
7 POWER board
3-4. TUNER BOARD, MAIN BOARD
5 cover, speaker
4 two screws
(BVTP3 × 10)
9 wire (flat type) (14 core)
(CNP323)
7 connector
(CNP802)
8 FFC cable 27P
(CNP801)
0 FFC cable 13P
(CNP322)
qa four screws
(BVTP3 × 10)
qs MAIN board
6 connector
(CNP321)
2 four screws
(BVTP3 × 10)
1 connector
(CNP1)
3 TUNER board
8

CFD-E75L
3-5. COVER PLATE ASSY
6 screw
(BVTP3 × 10)
2 connector
(CNP802)
6 screw
(BVTP3 × 10)
3 FFC cable 27P
(CNP801)
4 wire (flat type) (14 core)
(CNP323)
5 FFC cable 13P
(CNP322)
6 two screws
(BVTP3 × 10)
7 cover plate assy
1 connector
(CNP321)
3-6. CD MECHANISM DECK
(KSM-213CDP)
1 four screws
(2.6 × 10)
2 CD mechanism deck
(KSM-213CDP)
9

CFD-E75L
3-7. OPTICAL PICK-UP
(KSS-213C)
2 two claws
3 cover, CD
9 optical pick-up
(KSS-213C)
4 claw
1 two claws
5 gear (A)
7
6 claw
8 sled shaft
3-8. CABINET FRONT ASSY
4 Push the knob (stop/eject).
8 cabinet front assy
5
6 screw
(BTP2.6 × 8)
1 FFC cable 27P
(CNP801)
2 wire (flat type) (14 core)
(CNP323)
7 two screws
(BVTP3 × 10)
3 connector
(CNP321)
10

CFD-E75L
3-9. TAPE MECHANISM DECK
(MF-V5-117)
2 tape mechanism deck
(MF-V5-117)
1 four screws
(BVTP3 × 10)
3-10. CD LID
4 CD lid
3 boss
1 screw
(BTP2.6 × 8)
2 damper
CD lid
driver
11

CFD-E75L
3-11. LID CASSETTE ASSY, LCD BOARD
4 LCD board
1 two screws
(BTP2.6 × 8)
3 lid cassette assy
2 two claws
3-12. HEAD (HRP301), MOTOR ASSY (M301), BELT
2
3 Remove
four solders.
6 two screws
(B2.6 × 5)
4 TC board
1 screw
(BVTT2 × 6)
7 motor assy (M301)
8 belt
5 head (HRP301)
12

CFD-E75L
3-13. CONNECTOR SETTING
Note: When connecting leads, set it as shown in the figure.
TC board
CNP801
CN321
CN303
CNP802
CNP322
MAIN board
CN322
CNP321
CNP1
TUNER board
13

CFD-E75L
SECTION 4
MECHANICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head pinch roller
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagnetizer.
(Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
• Torque Measurement
Mode Torque Meter Meter Reading
2.95 – 6.86 mN•m
FWD CQ-102C (30 – 70 g•cm)
(0.42 – 0.97 oz•inch)
0.15 – 5.39 mN•m
FWD
CQ-102C
(1.5 – 5.5 g•cm)
Back Tension
(0.021 – 0.076 oz•inch)
more than 5.89 mN•m
FF CQ-201B (more than 60 g•cm)
(more than 0.83 oz•inch)
more than 5.89 mN•m
REW CQ-201B (more than 60 g•cm)
(more than 0.83 oz•inch)
• Tape Tension Measurement
FWD
Mode Tension Meter Meter Reading
CQ-403A
more than 100 g
(more than 3.53 oz)
SECTION 5
ELECTRICAL ADJUSTMENTS
PRECAUTION
1. Setting
MEGA BASS control : OFF
TAPE DECK SECTION
Test tape
Tape Speed Adjustment
Setting:
Function: TAPE
Procedure:
1. Playback WS-48A (tape center) in the FWD state.
2. Adjsut the volume in CAPSTAN/REEL motor (M301) so that
the frequency counter reading becomes 3,000 Hz.
Specified Value: 2,930 to 3,030 Hz
0 dB=0.775 V
Type Signal Used for
WS-48A 3 kHz, 0 dB Tape Speed Adjustment
Test tape
WS-48A
(3 kHz, 0 dB)
set
POWER board
CNP392 pin 1
3.2 Ω
frequency counter
3. Confirm that the frequency at the beginning and that at the
end of tape winding are between 2,940 to 3,060 Hz.
+
–
POWER board
CNP392 pin 2
Adjustment Location:
– TAPE deck block –
CAPSTAN/REEL motor
(M301)
Tape speed
Adjustment
14

CFD-E75L
TUNER SECTION 0 dB=1 µV
[MW/LW]
Setting:
Function : RADIO
RADIO BAND button : MW or LW
AM RF signal
generator
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
[FM]
Setting:
Function : RADIO
RADIO BAND button: FM
FM RF signal
generator
22.5 kHz frequency
deviation by 400 Hz
signal
Output level:
as low as possible
Put the lead-wire
antenna close to
the set.
0.01 µF
set
TUNER board
TP (ANT)
set
TUNER board
TP (GND)
POWER board
CNP392 pin 1
3.2 Ω
level meter
+
–
POWER board
CNP392 pin 2
POWER board
CNP392 pin 1
3.2 Ω
level meter
+
–
POWER board
CNP392 pin 2
digital voltmeter
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter
T1
450 kHz
MW VCO VOLTAGE ADJUSTMENT
Frequency Display
Reading on Digital Voltmeter
531 kHz 0.9 ± 0.5 V
1,611 kHz 5.2 ± 0.6 V
MW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3-1 621 kHz
CT3
1,404 kHz
LW VCO VOLTAGE ADJUSTMENT
Adjustment Part Frequency Display Reading on Digital Voltmeter
L4 153 kHz 0.6 ± 0.3 V
Confirmation 279 kHz 5.0 ± 0.15 V
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3-2 162 kHz
CT5
261 kHz
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
T2
10.7 MHz
FM VCO VOLTAGE ADJUSTMENT
Adjustment Part Frequency Display Reading on Digital Voltmeter
L2 108 MHz 3.0 ± 0.3 V
Confirmation 87.5 MHz 1.3 ± 0.4 V
TUNER board
TP (VT)
TP (GND)
100 kΩ
L1
CT1
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
87.5 MHz
108 MHz
• Repeat the procedures in each adjustment several times, and the
tracking adjustments should be finally done by the trimmer capacitors.
• Remove FM antenna in FM adjustment.
Adjustment Location: TUNER and POWER board (See page 16)
15

CFD-E75L
Adjustment Location:
– TUNER BOARD (Component Side) –
L4
LW VCO Voltage Adjustment
T2 FM IF Adjustment
L2
FM VCO Voltage Adjustment
T1 AM IF Adjustment
L1
CT1
FM Tracking Adjustment
L3-1
CT3
MW Tracking Adjustment
CT5
L3-2
LW Tracking Adjustment
– TUNER BOARD (Conductor Side) –
TP
(VT)
TP
(ANT)
TP
(GND)
– POWER BOARD (Conductor Side) –
1 4
CNP392
16

CFD-E75L
CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
Focus Bias Check
1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD
board.
2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)
3. Press the [ u] (CD) button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)
TIME/DIV: 500 ns
0.85 ± 0.2 Vp-p
When observing the eye pattern, set the oscilloscope
for AC range and raise vertical sensitivity.
Adjustment Location:
– CD BOARD (Conductor Side) –
IC701
TP (GND)
TP
(RF)
17

CFD-E75L
MEMO
18

SECTION 6
DIAGRAMS
CFD-E75L
6-1. BLOCK DIAGRAM – CD Section –
CNP701
2 2
DETECTOR
A
B
D 13 13
C
I-V AMP
10 10
11 11
CD BOARD
8 FIN2
7 FIN1 +
LPF
RF AMP, FOCUS/TRACKING SERVO,
DIGITAL SIGNAL PROCESSOR,
CLV SERVO, D/A CONVERTER
IC701
RF
MIX EQ AGC
4
PH
3
EFM
IN
SLISE LEVEL
CONTROL
RAM
ERROR
CORRECTION
AUDIO CD
C1 – 2, C2 – 2
INTERPOLATION
MUTE
ATTENUATION
DEEMPHASIS
8FS
DIGITAL
FILTER
1 BIT
DAC
AUDIO
OUT
LPF
LCHO
RCHO
DOUT
42
45
39
R-CH
CNP702
12
CD L-OUT
12
MAIN
BOARD
(1/4)
CNP323
CNP322
(1/5)
3
A
TO MAIN
SECTION
(Page 21)
F
E
9
14
9
14
BH
A/D
10 TIN1
SW
9 TIN1 TBAL LPF
TRACK
JUMP
RUPTURE
DETECT
CLV, CAV
CONTROL
PLL
VCEC
FRAME SYNC
DETECT,
PROTECT INSERT,
EFM DECODE
FSEQ
31
3
FSEQ
3
11 CD FSEQ
SERVO
PROCESSOR
RAM
OPTICAL PICK-UP
(KSS-213C)
LASER DIODE
AUDIO
ADJUST
DRF
DRF
67
4
DRF
4
10 CD DRF
PD
LD
7
7
AUTOMATIC
POWER
CONTROL
Q701
80 LDD APC
LDS
FE
TE
S/H
TDO
FDO
SLDO
SPDO
D/A
CONT4
SW
GENERAL-PURPOSE
PORTS
CONT1
*RES
CE
CL
DI
COMMAND
INTERFACE
DO
*WRQ
SYSTEM
CONTROLLER
IC801
(1/3)
79
13 15
20 21 23 22
25
72
66
61 62 63
64 65
5
5
6
*WRQ
6
1 CD-WRQ
(FOCUS)
2-AXIS
DEVICE
(TRACKING)
3
2
3
2
T+
12
T–
11
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC702
TRACKING
COIL DRIVE
TIN
9
5
9
7
8
10
DO
DI
CL
CE
*RES
5
9
7
8
10
8 CD DO
9 CD DI
7 CD CL
6 CD CE
5 CD-RES
4
1
4
1
17
18
F+
F–
FOCUS
COIL DRIVE
FIN
19
CD DOOR
20
M702
(SLED)
M
26 SL+
27
SL–
SLED
MOTOR DRIVE
SLIN
25
S901
CD LID
OPEN/CLOSE
1
2
CNP801
M701
(SPINDLE)
M
2
1
SP+
SP–
SPINDLE SPIN
MOTOR DRIVE
3
MUTE
7
S701
(LIMIT)
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: CD PLAY
19
19

CFD-E75L
6-2. BLOCK DIAGRAM – TUNER Section –
ANT1
FM TELESCOPIC
ANTENNA
TUNER BOARD
D10
D11
L1
FM RF
CT1, L1
FM TRACKING
CT1
2
24
FM/AM RF AMP, MIX, OSC,
FM/AM IF AMP, DET, MPX
IC1
FM RF
IN
FM
RF OUT
FM
RF AMP
FM
MIX
FM
OSC
MIX OUT
CF2
10.7MHz
4 7
T1
AM IFT
CF4
450kHz
6
FM
IF IN
AM
IF IN
FM IF
AMP
AM IF
AMP
QUAD
T2
FM IFT
T2
FM IF
10
FM
DET
AM
DET
AF
BUFFER
DET
OUT
16
AM HIGH
CUT
SWITCH
Q12
MPX
IN
15
AF
AMP
MPX
MUTE
R-OUT
STEREO/
MONO,
FM/AM
L-OUT
12
11
CNP1
L-CH
R-CH
6
MAIN BOARD
(2/4)
CN321
(1/2)
CNP322
(2/5)
6 L-CH 1
B
TO MAIN
SECTION
(Page 21)
L3
MW/LW FERRITE-ROD
ANTENNA
L3-1
MW
L3-2
LW
B+
Q41
Q41, 42
MW SWITCH
CT3, L3-1
MW
TRACKING
CT5, L3-2
LW
TRACKING
Q43
LW SWITCH
CT5
Q43
Q42
CT3
D1
D3
(1/2)
22
AM RF
IN
AM
RF AMP
L4
LW VCO VOLTAGE
L4
MW/LW OSC
D3
(2/2)
AM
MIX
AM
OSC
AM OSC
FM OSC
20 21
Q44
LW
SWITCH
D2
BUFFER
BUFFER
OSC
OUT
L2
FM VCO VOLTAGE
19
L2
FM OSC
T1
AM IF
IF
BUFFER
IF OUT
LEVEL
DET
ST
IND
ST IND
17 18
LPF1/BAND
LPF2/MO-ST
13 14
R-MUTE
11
CONSTANT
CURRENT
Q61
VT
2
FM/AM PLL
IC2
MW BAND
SELECT SWITCH
Q14
6
18
LOW-PASS
FILTER
17 16
12
11
10 8 9
7
13
C
FROM MAIN
SECTION
(Page 21)
X1
75kHz
21
20
XOUT
XIN
REFERENCE
DIVIDER
MW/LW
LP-OUT
LOW-PASS
FILTER
UNLOCK
DETECT
LP-IN
PD
PHASE
DETECTOR/
CHARGE PUMP
12 BIT
PROGRAMMABLE
DIVIDER
SWALLOW
COUNTER
FM IN
1/2
AM IN
IF IN
UNIVERSAL
COUNTER
ST-IND
BAND
BAND
MO/ST
CCB
INTERFACE
DI
CL
CE
DO
2
3
1
4
R-DATA
R-CLOCK
R-CE
R-COUNT
8
9
7
10
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: FM
SHIFT REGISTER & LATCH
: MW/LW
20
20

CFD-E75L
6-3. BLOCK DIAGRAM – MAIN Section –
L-CH
R-CH
A
FROM CD
SECTION
(Page 19)
B
FROM TUNER
SECTION
(Page 20)
HRP301
(REC/PB)
HE301
(ERASE)
3
1
TC BOARD MAIN BOARD (3/4)
POWER BOARD (1/2)
CN303 (1/4)
CD IN L
TU IN L
PB
REC
S301 (1/2)
(REC/PB)
Q302
VREF
1
R-CH
VREF
T301
BIAS OSC
Q303
2
1 2
5
4
6
REC/PB EQ AMP
IC301
MIC IN
13
L.CD
24
L.RAD
22
L.IN
L.RO
VREF
PB
EQ AMP
BIAS OSC
Q301
Q302, 303
ISS SWITCHING
CN303 (2/4)
CNP302 (5/5)
REC
EQ AMP
DET
BUFFER
ALC
REFERENCE VOLTAGE
GENERATOR
S301 (2/2)
(REC/PB)
PB REC
MIC
AMP
CD B+
COM 5V
CN303 (4/4)
CNP322 (4/5)
LINE
TAPE
REC
R-CH
BUFFER
17 15 21
MUTE
LOGIC CIRCUIT
7
7
11
11
MUTE
MONITOR
AMP
CN303
(3/4)
L.LO
5 5
VIN2 VOUT2
3 3 L IN
AF AMP
20 8
7 +
11
Q120
XTAL
EXTAL
CNP322
(3/5)
12 13 16 3
V-DATA
V-CLOCK
TX
A-MUTE
TEX
32 31 73 74
23 24
BUZZER
ELECTRICAL VOLUME
IC320
R-CH
LOGIC
CONTROL
DATA
4 5
71
BEEP H/L
CLOCK
BUZZER H/L
CONTROL
Q431
15
MEGA
BASS
KEY-1
KEY-2
Q122
MUTING
R-CH
JOG-A 26
JOG-B 25
CN322
(1/2)
CNP802
2 2
6
5
6
5
CNP391
(1/2)
STANDBY
7
STANDBY
SWITCH
POWER
AMP
POWER
AMP
IC390
L OUT
5
KEY POWER BOARD
CN401
MEGA BASS
CONTROL
Q291
D394
D390
D320
CNP401
5
4
1
2
TC POWER
B+
R-CH
CNP392
1
2
4
3
J301
(HEADPHONE)
(L-CH)
(R-CH)
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: CD PLAY
: TUNER (FM/AM)
: TAPE PLAY
: TAPE RECORD
2
1
2
1
CN404
CN403
JOG BOARD
RE401
ROTARY
ENCODER
i
(JOG DIAL)
S407
ALARM
MENU
S406
DSPL
ENT MEM
C
TO TUNER
SECTION
(Page 20)
VT
R-MUTE
R-DATA
R-CLOCK
R-CE
R-COUNT
2
11
8
9
7
10
CN321 (2/2)
D321
70
TC POWER
B+
TU-MUTE
68 TU-DATA
69 TU-CLK
66 TU-CE
78 TU-COUNT
77
ISS-2
76
ISS-1
SYSTEM CONTROLLER
IC801 (2/3)
67 79
TAPE
TC-REC
SHIFT
CLK
29
Q804
X801
4.19MHz
Q803, 804
SHIFT CLOCK
Q803
X802
32.768kHz
OPR/BATT B+
4
3
1
4
3
1
S401 – 405
CNP402
S401
OPERATE
S402
STANDBY
S403
RADIO BAND
AUTO PRESET
S404
TUNE
m
–
S405
TUNE
M
+
2
2
CN402
S408 – 413
S408
x
KEY VOLUME BOARD
OPT/BATT LED
BOARD
D401
OPR/BATT
S409
u
S410
VOLUME –
S411
VOLUME +
S412
MEGA BASS
S413
MODE
21
21

CFD-E75L
6-4. BLOCK DIAGRAM – POWER SUPPLY Section –
SEG0 – SEG19
42 – 61
MAIN BOARD (4/4)
CNP801
5
ı
24
5
ı
24
LCD BOARD
LIQUID CRYSTAL
DISPLAY
LCD801
COM0 – COM3
38 – 41
38
ı
41
38
ı
41
RMC
2
26
26
CNP811
REMOTE AAAA
CONTROL BBBB
RECEIVER CCCC
DDDD IC804
SYSTEM
CONTROLLER
IC801
(3/3)
CD 18
CD B+
CD VCC 3.3V
CD +3.3V
REGULATOR
Q325, 326
CD 6.2V
CD B+
SWITCH
Q325, 326
CN322
(2/2)
11
CD 6.2V
11
CN391
(2/2)
CD +6.2V
REGULATOR
Q391
POWER AMP
(IC390) B+
D905
D906
POWER BOARD (2/2)
T901
POWER
TRANSFORMER
AC INLET BOARD
J901
- AC IN
TUNER VCC 6V
TUNER B+
SWITCH
Q322, 323
RADIO 65
RECT
D901 – 904
CNP902
1
1
CN902
TC 6V,
ELECTRICAL VOLUME (IC320) B+
RCM 5V
D324
1
AU 6.2V
1
+6.2V
REGULATOR
Q390
2
3
2
3
OPR/BATT B+,
TC POWER B+
7
TC 9V
7
B+ SWITCH
Q392, 393
P-CON 19
RST 30
µCOM (VDD) B+
RESET SIGNAL
GENERATOR
IC803
COM +3.3V
REGULATOR
IC321
8
9
P-CON
COM VCC
8
9
CNP901
1
2
BATY A BOARD
CN901
1
2
DRY BATTERY
SIZE“D”
(IEC DESIGNATION R20)
6PCS. 9V
(FOR POWER SUPPLY)
REG CHK 21
BATTERY
CHECK
Q328, 329
D323
D322
10
AC-HI
10
DRY BATTERY
SIZE“AA”
(IEC DESIGNATION R6)
3PCS. 4.5V
(FOR BACK UP)
CNP321
TC POWER
B+
6
5
S303
(MOTOR ON/OFF)
TC PLAY 80
4
3
1
2
M
M301
(CAPSTAN/REEL)
S304
(TAPE PLAY)
3
3
BATY B BOARD
BACK-UP
BOARD
22
22

CFD-E75L
• Waveforms
– CD Board –
– TUNER Board –
– MAIN Board –
• Circuit Boards Location
1 IC701 4 (RF) (CD Play mode)
500 mV/DIV, 1 µs/DIV
5 IC2 w; (XOUT)
500 mV/DIV, 5 µs/DIV
7 IC801 es (XTAL)
1 V/DIV, 100 ns/DIV
KEY POWER board
TUNER board
0.85 ± 0.2
Vp-p
1.4 Vp-p
3.4 Vp-p
OPR/BATT LED board
13.3 µs
239 ns
JOG board
2 IC701 qd (FE) (CD Play mode)
20 mV/DIV, 1 µs/DIV
8 IC801 ud (TX)
1 V/DIV, 10 µs/DIV
MAIN board
Approx.
90 mVp-p
3.6 Vp-p
TC board
KEY VOLUME board
30.6 µs
– TC Board –
3 IC701 qg (TE) (CD Play mode)
20 mV/DIV, 1 µs/DIV
6 T301
20 V/DIV, 5 µs/DIV
POWER board
AC INLET board
CD board
Approx.
60 mVp-p
33.6 Vp-p
BATY A board
17.2 µs
4 IC701 rk (XOUT)
1 V/DIV, 10 ns/DIV
BATY B board
2.9 Vp-p
LCD board
BACK-UP board
29.5 ns
23
23

JW723
JW725
C743
JW708
JW729
JW727
JW709
JW706
C735
CFD-E75L
6-5. PRINTED WIRING BOARD – CD Section – • See page 23 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location
IC701 C-4
IC702 H-3
Q701 F-5
A
1 2 3 4 5 6 7 8
CD BOARD
R715
R714 C713
JW701 JW702
C727
B
C712
JW703
JW705
C711 C709
C754
JW730
JC704
FB701
C716
IC701
R723
C
R755
C755
R754
L706 C717
X701
C722
R716 C720
C721
R718
C742
JW707
C708
C707
C732
D
E
F
D
MAIN BOARD
CNP323
(Page 29)
R743
CNP702
M
M702
(SLED)
JW728
C724
R717
R719
C725
C723
R720
R721
C726
R724
R722
R731
C745
C746
JW724
R726
R725
C729
C728
C747
C702
JW726
R729
C730 R730
R707
C744
R728
Q701
C703
R727
C701
TP
(GND)
C731
C751
R708
C704
TP
(RF)
C734
JW712
C705
R711 R710
CNP701
JC703 JC705
C736
R704
R709
JW714
R712
R702
R703
JW711
R705
JW713
JW710
R701
R706
C706
C750
C733
JW722
G
R744
JW720
JW719
C740
C741
JW718
JW721
S701
(LIMIT)
JW716
JW715
OPTICAL
PICK-UP
(KSS-213C)
H
R745
R741
M
M701
(SPINDLE)
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• f : internal component.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
IC702
JW717
JC701
JC702
1-680-943-
12
(12)
24
24

B3
B5
B1
C2
R743
JC702
R744
6.8k
JC701
100k
C3 C4
B4
B2
C1
B2
B3
B4
B5
A1
R726
A2
A8
A4
A3
A7
A5
A6
C723
C725
C726
C727
680
SP+
C720
C721
C722
C724
R725
680
22p
22p
22p
0.01
22p
1000p
1000p
1000p
C728
0.047
SPIN
RST
REG-B
REGO
MUTE
GND
TIN
(TIN)
T-
T+
GND
SP-
SL-
SL+
SLIN
(SLIN)
VREF
VCC
VCC
(FIN)
FIN
F-
F+
GND NC
OPOUT OPIN
FX FY
SPX
SPY
SLX SLY
FDO
SPDO
SLDO
GPDAC
CONT4
CONT5
SBCK/CONT6
SBCK/FG
DEFECT
V/*P
FSEQ
MONI1
MINI2
MONI3
MONI4
MONI5
(3.3V)VSS
VDD
DOUT
LDD
LDS
FR
VVDD
PCKIST
VVSS
PDO2
PDO1
CONT1
CONT2
CONT3
VSS
VDD5
DRF
*RES
*WRQ
DO
DI
CL
CE
CFD-E75L
6-6. SCHEMATIC DIAGRAM – CD Section – • See page 23 for Waveforms. • See page 36 for IC Block Diagrams.
SW
S701
(LIMIT)
GND
C729
1
R724
C747 C730 C744
47k 100 0.1
0.1
10V
R731
2.2k
R730
1k
R729
220
R728
10k
R727
2.2k
C746
100
10V
C745
0.1
CNP702
14P
P-GND
CNP701
16P
VREF
VCC
E R701
D R702
A R703
B R704
C R705
F R706
GND
LD
VR R712
PD
F+
T+
T-
F-
47k
15k
15k
15k
15k
47k
100
C1
C2
C3
C4
R707
C702
10
47
10V
Q701
KTN2907AS-RTK
AUTOMATIC
POWER CONTROL
C701
1000p
C732
100
10V
C733 C751 C750
100 0.1 100
10V
10V
C704
22p
R709
22k
C703
0.1
TP
(GND)
C706
1
50V
C731
0.047
R710
4.7k
C707
1
B1
R711
330
R708
10k
TP
C705
4700p
(RF)
(VC)
C734 4700p
(FE)
(TE)
C736 JC703
4700p
C708 100p
TX TY
SLCO
SLCIST
EFMIN
RF
RFVDD
RFVSS
FIN1
FIN2
TIN1
TIN2
VREF
REFI
FE
TEC
TE
RFMON
JITTC
ADAVDD
ADAVSS
TDO
DATA
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
16MOUT
EFLG
C2F
RF AMP,FOCUS/TRACKING SERVO,
XVSS
DIGITAL SIGNAL PROCESSOR,
FSX/16MIN
CLV SERVO,D/A CONVERTER
IC701
XIN
LC78645NE
XOUT
XVDD
RVDD
RCHO
RVSS
LVSS
LCHO
TEST LVDD
C717
0.01
C716
0.01
C711
0.01
X701
33.868MHz
JC704 220
FB701 C713
0.01
R715
150
C712
R714
0.01
150
A9
A10
A1 R723 100
A2 R722 100
A3 R719 100
A4 R720 100
A5
A6
A7
A8
A9
A10
C755 C754
0.01 0.01
R755
R754
0
0
L706
R717 1k
R716 1k
R718 1k
R721 1k
(R-CH)
(L-CH)
CD MOTOR 6.0V
FSEQ
DRF
DO
*WRQ
CL
CE
DI
*RES
CD R-OUT
CD L-OUT
D-GND
CD VDD 3.3V
(Page 30)
C743
0.1
C742
0.1
C709
0.1
C735
1000
6.3V
FOCUS/TRACKING
COIL DRIVE,
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• f : internal component.
SPINDLE/SLED
MOTOR DRIVE
IC702
BA6998FP-E2
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
M702
(SLED)
M701
(SPINDLE)
SL+
SL-
SP+
SP-
R741
6.8k
C741
0.1
C740
470
10V
• A : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD STOP
( ) : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY
25
25

JC24
CFD-E75L
6-7. PRINTED WIRING BOARD – TUNER Section – • See page 23 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10
A
TUNER BOARD
ANT1
FM TELESCOPIC
ANNTENA
L3 – 1
MW FERRITE-ROD
ANTENNA
L3 – 2
LW FERRITE-ROD
ANTENNA
Q14
B
C
D
E
A
MAIN BOARD
CN321
(Page 29)
CNP1
1
11
TP
(VT)
C58
TP
(GND)
JC1
R61
R60
R59
R58
R66
JC33
L21
R63
JC34
R10
JW3
Q61
C61
C62
C63
R13
R64
C64
R94
R19
C60
C29
C51
R22
R17
C52
IC2
C66
C68
R42
R18
R56
X1
R93
C2
R16
C5
R9
C59
JC2
R50
C55
R52
C95
C57
Q41
C6
R4
C3
C53
R53
JW5
R54
R51
C37
JC5
CT5
JW4
C54
R91
Q43
Q44
R7
JW6
JC4
JC22
C48 R43 C45
C46
C73
JW7
C71
C72
C70
–1 –2
C39
CT3
R40
C49
JW8
R2
C44
D2
R30
C33
C40
Q12
C93
R12
C41 C42
C43
JC3
L4
MW/LW OSC
C25
R11
C21
JW9
C30
D3
L2
FM OSC
C56
C22
C31
Q42
R41
JW10
C24
C23
R31
R24
C20
R92
C77
R32
C32
CT1
C78
IC1
C80
C14
C15
D1
C11
C34
C35
C12
C7
C1
C18
C9
L1
FM RF
C4
JW12
JW11
JW13
JC23
T1
AM IF
CF2
D10
C8
R3
CF4
T2
FM IF
D11
C10
R1
TP
(ANT)
JC6
JW1
1-680-952-
JW2
11
(11)
• Semiconductor Location
Ref. No.
Location
D1 C-8
D2 C-6
D3 C-6
D10 B-9
D11 B-9
IC1 D-3
IC2 D-7
Ref. No.
Location
Q12 E-5
Q14 B-3
Q41 B-4
Q42 C-6
Q43 B-5
Q44 C-5
Q61 C-3
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• W : indicates side identified with part number.
• f : internal component.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
26
26

AM
LOW CUT
CE
DI
CL
DO
MUTE
MW/LW
BAND
ST-IND
BAND
IF IN
XOUT
XIN
LP-OUT
LP-IN
PD
VSS
VDD
MO/ST
FM IN
AM IN
D1
KV1471E
D2
KV1471E
CFD-E75L
6-8. SCHEMATIC DIAGRAM – TUNER Section – • See page 23 for Waveform. • See page 36 for IC Block Diagrams.
C72
22p
C71
100p
C44
220p
L3
-1
L3-1
MW FERRITE-ROD
ANTENNA
R18
4.7k
Q44
2SC4098
LW SWITCH
R9
100k
C5
C6
0.01 0.01
R7
470k
C41 220p
D3
KV1520NT
CT3 R41 C49 R40
10p 10k 0.1 470k
C42
100p
C43
47p
C70
5p
C40
10p
C39
0.1
L4
MW/LW OSC
R50
1k
R91
1k
R52
100
R64
1k
C53
0.47
R51
10k
C54
220
10V
C56
1000p
S
Q61
2SK514-F
CONSTANT
CURRENT
R63
4.7k
C46
0.1
Q42
2SC4098
MW SWITCH
C45
0.01
R43
10k
-2
L3-2
LW FERRITE-ROD
ANTENNA
R42
100k
Q41
DTC343TK
MW SWITCH
R16
10k
C3
0.01
CT5 C48
50p 47p
Q43
2SC2059K
LW SWITCH
C73
22p
C34
0.01
R32
100k 15k
0.01
CT1
20p
C35
L1
C33
0.01 0.01
FM
RF
L2
R30
FM OSC
R31
3.3k
C31
22p
C30
0.01
C80
C37
0.01
Q12
DTC114YUA
AM HIGH
CUT
SWITCH
C25 R12
4700p 47k
JC22
C93
0.01
Q14
2SC4081
MW BAND
SELECT
SWITCH
C51 C52
C2 22p 10p
0.01
X1
75kHz
R22
10k
R19
2.2k
R17
2.2k
C59
1000p
R53
4.7k
R54
470
C95
1000p
C55
100p
C57
1000p
TP
(VT)
JC3
R24
220
C24
220p
R11
3.3k
C22
0.1
FM/AM PLL
JC24
C23
1
50V
C21
1
50V
IC2
LC7213M-TLM
C20
0.1
C60
FM
RF-OUT
GND1
VCC1
FM
RF-IN
AM
RF-IN
MIX-
FM OSC
OUT
AM OSC
VCC2
OSC-OUT
AM
IF-IN
FM
ST-IND
IF-IN
IF-OUT
GND2
DET-OUT
AGC
MPX-IN
QUAD
LPF2
/MO-ST
R-OUT
LPF1
/BAND
L-OUT
FM/AM RF AMP,
MIX,OSC,IF AMP,
DET,MPX
IC1
TA2149N
R66
47
R93
1k
C61
100p
C64
100p
1000p
R94
1k
R4
10k
JC5
C12
4.7
50V
C62
100p
R56
330
C58
0.01
ANT1
FM TELESCOPIC
ANTENNA
JC23
C11
0.1
C9
10p
C7
5p
C63
100p
R92
1k
C66
100p
C68
100p
R13
2.2k
L21
10µH
T1
TP
(ANT)
C1
47p
AM IFT
JC4
R61 R60 R59 R58
2.2k 2.2k 2.2k 2.2k
CNP1
11P
C32
1000p
R2
470
R3
10k
JC6
R1
470
CF4
450kHz
T2
FM IFT
JC33
JC2
R10
47
JC1
R-MUTE
R-COUNT
R-CLOCK
R-DATA
R-CE
CF2
L-OUT
D10
1SS355
D11
1SS355
C4
1000p
C10
1
50V
C8
1000p
10.7MHz
C18
220
10V
C14 C15
C77 C78
0.01 0.01 4700p 4700p
JC34
C29
100
10V
RADIO 6V
R-OUT
A-GND
VT
S-GND
(Page 30)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• f : internal component.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : MW
[ ] : LW
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal
production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : MW/LW
27
27

C203
IC301
JC302
R102
C104
CFD-E75L
6-9. PRINTED WIRING BOARD – TAPE DECK Section –
• See page 23 for Circuit Boards Location.
6-10. SCHEMATIC DIAGRAM – TAPE DECK Section –
• See page 23 for Waveform. • See page 37 for IC Block Diagram.
1 2 3 4 5 6
A
B
C
B
MAIN BOARD
CNP322
(Page 29)
TC BOARD
C303
C301
R111
R309
R105
R301
R304 JC302
CN303
C106
C206
JC304
R313
R303 JC301
R211
R201
R206
R302 R205
R106
4
R110
C105
C205
1 3 2
C103
R104 R103
C101
C107
R101
C102
C201
C302 C204
C207
R202
R204
R203
C202
R210
S301
(REC/PB)
PB
r
REC
-1 -2
R305
L-CH
R-CH
HRP301
REC/PB
HEAD
HE301
(ERASE HEAD)
L-CH
HRP301
(REC/PB HEAD)
R-CH
HE301
(ERASE HEAD)
1
4
S301
(REC/PB)
REC
PB
C301
100
10V
R301
1M
R110
100
R210
100
C102
47 10V
C104
0.0022
C101
0.001
C107
470p
R101
15k
R201
15k
C207
470p
C201
0.001
C204
0.0022
C202 R202
47 68
10V
R102 R103
68 68k
C103
0.047
C105
47p
C302
100 10V
C203
0.047
R203
68k
R104
2.2k
C205
47p
R204
2.2k
REC/PB EQ AMP,
SELECT SWITCH
AGC
L.LIN
L.PO MIC
I/EX
L.NF
L.RAD
L.RO
REC
L.IN
L.LO
REF
VCC
GND
R.LO
R.IN
LINE
R.RO
R.RAD
R.NF
TAPE
R.PO
R.LIN
MIC.NF
MIC
IC301
TA2068N
R106
2.2k
R206
2.2k
R211
4.7k
R302 R303 R304
4.7k 4.7k 1k
R111
4.7k
C106
1
50V
C303
100 10V
C206
1
50V
R309
47
R105
15k
R205
JC301
15k
CN303
13P
TU-IN-L
TU-IN-R
CD-IN-L
CD-IN-R
L-OUT
R-OUT
LINE
D
R312
Q303
Q302
JC303
R310
R311
C310
C308
C307
C304 R306
R307
Q301
C306
R308
C305
T301
BIAS
OSC
Q302
2SC2412KT-
146-QR
1-679-592-
11
(11)
-1 -2
Q302,303
ISS SWITCHING
C310
220p
C308
100p
C305
470p
Q303
2SC2412KT-146-QR
T301
BIAS OSC
R308 C306
22k 0.01
R305
150
R306
6.8k
Q301
2SC2412KT
-146-QR
JC303
JC304
TAPE
6V
GND
(Page 30)
BIAS OSC
R310
1M
R312 R311 R313
1k 1M 1k
C304
47
10V
C307
0.0022
R307
15
• Semiconductor
Location
Ref. No.
Location
IC301 C-3
Q301 D-4
Q302 D-2
Q303 D-2
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• A : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : TAPE PLAY
( ) : TAPE RECORD
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER
E : TAPE PLAY
a : TAPE RECORD
J : CD PLAY
28
28

C835
C836
R837
R839
R841
R843
R845
R847
C834
R834
R835
R836
R838
R840
R842
R844
R846
R848
R850
R852
R854
R856
R858
R860
R849
R851
R853
R855
R857
R859
R861
CNP322
CFD-E75L
6-11. PRINTED WIRING BOARDS – MAIN/LCD Boards – • See page 23 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A
MAIN BOARD
B
C
D
E
F
G
H
I
S304
(TAPE PLAY)
M301
(CAPSTAN/REEL)
S303
(MOTOR ON/OFF)
M
F
C
6
5
4
3
2
1
POWER BOARD
(Page 34)
POWER BOARD
CNP391
(Page 34)
D
CD BOARD
CNP702
(Page 24)
R328
D324
R327
JW310
JW317
CN322
D325
L321
JW311
IC321
D322 3
R336
Q329
R323
R330
R333
1
D323
R324
JW315
Q326
JW314
R326
C332
C328
JW306
C335
JW316
Q327
JW313
C818
C819
Q328
JW309
C820
JW304
R332
JW312
JW308
R884
R331
R329
JW341
CNP321
JW307
D320
JW318
Q325
C813
R818
R820
R827
R816
R886
C824
R830
R883
Q222
D327
C330
C826
1
3
IC803
R882
C830
R819
C812
R812
R881
C885
C892
Q122
R815
C825
C890
JW322
R811
R813
C823
CNP802
R321
Q803
C882
C883
C884
C331
R824
R826
R894
R829
C324
JW319
C810 C801
Q804
CNP323
JW320
JW323
R809
R801
R810
C881
C887
R808
R821
R823
R825
R828
X801
R893
R832
C886 C889
R892
R891
R807
R130 R224
C220
R806
R230
JW328
C329
R805
C888
R803
JW302
C837
R223
JW321
JW325
JW305
R871
C120
R432
JW329
R431
C431
R123
R124
Q431
R334
C124
R335
JW330
IC801
C224
C322
R890
CNP801
C323
R888
X802
IC320
R873
JW331
L801
C126
C223
R221
L802
C226
R877
R879
C872
C874 C875
R876
C880
C873
R880
R320
C321
R878
C805
JW332
C320
R125
JW338
C803
R802
Q220
JW335
R896
D326
R225
C327
R867
C123
JW336
JW333
R222
R220
R876
R866
R865
C326
C351
R870
R868
R120
C802
R325
Q120
JW326
R121
C865
R322
JW327
R869
C868
R895
C866
JW343
R122
C869
JW339
D321
JW337
C125
C225
(Page 28)
R899
C325
L322
C127
CN801
B
TC BOARD
CN303
C227
C334
S901
CD LID
OPEN/CLOSE
JW344
D328
CN321
D329
JW345
Q323
Q322
A
TUNER BOARD
CNP1
(Page 26)
LCD BOARD
24 20 15 10 5 1
CNP811
LCD801
LIQUID CRYSTAL DISPLAY
IC804
3 2 1
J
E
KEY POWER BOARD
CN401
(Page 32)
JW301
13
(13)
• Semiconductor Location
1-681-670-
1-681-675-
13
(13)
Ref. No.
Location
Ref. No.
Location
Ref. No.
Location
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
D320 B-5
D321 C-11
D322 F-3
D323 F-3
D324 D-3
D325 F-3
D326 H-9
D327 D-5
D328 D-12
D329 D-13
IC320 C-8
IC321 F-3
IC801 G-7
IC803 H-5
IC804 H-6
Q120 D-11
Q122 C-5
Q220 D-10
Q222 C-5
Q322 D-13
Q323 E-13
Q325 E-4
Q326 D-3
Q327 D-4
Q328 G-3
Q329 G-3
Q431 E-7
Q803 H-5
Q804 H-6
29
29

R-MUTE
R333
470
C126
C226
D326
UDZ-TE-17-5.1B
1 50V
1 50V
R328
R327
R336
R125
R225
100
100
470
15k
R-COUNT
15k
R-CLK
R-DATA
R-CE
RADIO
ISS-2
ISS-1
TAPE
TC-REC
TC-PLAY
V-CLOCK
V-DATA
MEGABASS
A-MUTE
BUZZER
P-CON
REG-CHK
RMC+5V
D-GND
OPR/BATT
CD
U-CON(VDD)
CD-RES
CD-DI
CD-CE
CD-CL
AA5
AA4
AA3
AA2
AA1
D324
1SS355TE
-17
CD-WRQ
CD-DO
CD-DRF
D325
1SS355TE
-17
CD-FSEQ
*RES
DI
CE
CL
*WRQ
DO
DRF
FSEQ
ISS2
ISS1
TAPE
REC
PLAY
OUT
IN
GND
CFD-E75L
6-12. SCHEMATIC DIAGRAM – MAIN Board (1/2) –
(1/2)
R320
150
C320
100
10V
C124
1
50V
R123
C120
1k 0.0022
R325
C123
150 R120
1
1k
50V
C321
0.01
R124
6.8k
R121
220k
Q120
KTC3198GR-AT
AF AMP
Q122
DTC343TKA-T146
C324
0.1
R321
47k
C326
100
10V
R122
220
Q122,222
MUTING
C331
47
10V
R222
220
ELECTRICAL
VOLUME
S303
(MOTOR ON/OFF)
CNP321
6P
Q220
KTC3198GR-AT
IC320
M62429P
Q222
DTC343TKA-T146
AF AMP
M301
(CAPSTAN/REEL)
S304
PLAY
R221
220k
R224
6.8k
(TAPE PLAY)
R220
1k
R223
1k
C220
0.0022
TU-IN-L
TU-IN-R
C223
C224
1 50V 1 50V
CD-IN-L
CD-IN-R
L-OUT
R334
330
C322
100p
C323
100p
R-OUT
LINE
R335
330
(Page 28)
TAPE
6V
GND
TAPE
R130
CN322
13P
L-OUT
REC
REC
220k
R-OUT
ISS1
ISS2
CNP322
13P
C225
1
50V
ISS1
ISS2
C125
1
50V
C325
220
10V
D321
1SS355TE
-17
R322
100
D320
1SS355TE-17
R230
220k
A-GND
AU 6.2V
M/B-CONT
MOT-GND
TC 9.0V
P-CON
(Page 35)
C227
100p
D322
1SS355TE-17
COM VCC
AC-HI
CN321
11P
S-GND
C127
100p
D323
1SS355TE-17
CD 6.2V
D-GND
S-GND
(Page 35)
(Page 27)
VT
A-GND
R-OUT
RADIO 6V
L-OUT
R-CE
R-DATA
R-CLOCK
R-COUNT
R-MUTE
L322
1µH
AA1
AA2
AA3
AA4
AA5
Q322
DTC114YKA
-146
D328
1SS355TE-17
D329
1SS355TE-17
Q323
DTA114EKA
-T146
C334
10
50V
C351
100p
Q328,329
BATTERY
CHECK
Q329
KTC3875GR
Q328
DTA114YKA
-T146
C335
2.2
50V
R323
10k
R324
1k
R326
330
C327
220
16V
COM +3.3V
REGULATOR
IC321
S-81233SGY
C328
0.1
L321
10µH
C332
100
10V
CNP323
14P
Q322,323
TUNER B+ SWITCH
Q325
DTC114YKA-T146
R330
100k
D327
UDZ-TE-17-3.9B
C330
100
10V
FSEQ
P-GND
CD MOTOR 6.0V
FSEQ
R332
DRF
DRF
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• A : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : TUNER
[ ] : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Signal path.
F : AUDIO
(Page 31)
Q325,326
CD B+ SWITCH
R329
1k
Q326
KTA1271Y-AT
R331 220
100
Q327
KTC3203Y-AT
Q327
CD +3.3V REGULATOR
C329
0.01
DO
*WRQ
CL
CE
DI
*RES
DO
*WRQ
CL
CE
DI
*RES
CD R-OUT
CD L-OUT
D-GND
CD VDD 3.3V
(Page 25)
30
30

R890
R888
C810
C812
C818
C819
C820
330k
330k
R892
R893
R894
R827
R801
R802
R803
R805
R806
R807
R808
R809
R810
R811
R812
R813
R815
R816
R818
R821
R819
R820
C865
C866
C868
C869
0.1
100p
100p
100p
R-MUTE
R-COUNT
R-CLK
R-DATA
R-CE
RADIO
ISS-2
ISS-1
TAPE
TC-REC
TC-PLAY
V-CLOCK
V-DATA
1k
MEGABASS
1k
10k
A-MUTE
0.1
100p
100p
10k
100k
100k
1k
1k
1k
1k
1k
1k
1k
1k
1k
1k
1k
22k
1k
1k
X801
4.19MHz
C892
0.01
C837
C836
C835
C834
R861
R860
R859
R858
R857
R856
R855
R854
R853
R852
R851
R850
R849
R848
R847
R846
R845
R844
R843
R842
R841
R840
R839
0.01
0.01
0.01
0.01
47k
BUZZER
10k
47k
47k
P-CON
100p
47k
REG-CLK
100p
47k
47k
47k
RMC+5V
4.7k
47k
47k
D-GND
47k
OPR/BATT
47k
47k
CD
R-MUTE
R-COUNT
R-CLK
R-DATA
R-CE
RADIO
ISS-2
ISS-1
TAPE
TC-REC
MEGABASS
A-MUTE
P-CON
REG-CHK
CD
CD-RES
CD-DI
CD-CE
CD-CL
CD-WRQ
CD-DO
CD-DRF
CD-FSEQ
CD-WRQ
CD-RES
CD-CE
CD-CL
CD-DO
CD-DI
CD-REF
CD-FSEQ
MEGABASS
A-MUTE
CD
P-CON
47k
U-CON(VDD)
47k
47k
CD-RES
RMC
V-DATA
V-CLOCK
47k
CD-DI
47k
47k
CD-CE
47k
CD-CL
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
47k
47k
CD-WRQ
47k
CD-DO
BUZZER
A-MUTE
47k
CD-DRF
CD-FSEQ
CD-WRQ
N.C
CD-RES
CD CE
CD CL
CD DO
CD DI
CD DRF
CD FSEQ
N.C
MEGABASS
N.C
CD
P-CON
CD DOOR
REG CHK
N.C
KEY-1
KEY-2
N.C
N.C
N.C
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM3
RESET
VCC
GND
GND
SIGNAL
RMC+5V
CFD-E75L
6-13. SCHEMATIC DIAGRAM – MAIN (2/2)/LCD Boards – • See page 23 for Waveforms.
IC804
SPS-442E
REMOTE CONTROL
RECEIVER
LCD801
LIQUID CRYSTAL DISPLAY
CNP811
27P
(2/2)
CNP801
27P
R838
47k
R837
100k
RESET SIGNAL
GENERATOR
IC803
PST9128-T
R836
100k
R835
100k
R834
33k
RADIO
R-CE
TAPE
R-DATA
R-CLK
R-MUTE
ISS-1
ISS-2
TC-REC
R-COUNT
R879
100k
C803
47 10V
C802
0.01
L801 C872
100µH 10p
C873
22p
L802
2.2µH C805 C875
0.1 5p
C874
R876 1k
R877 1k
R878 1k
R865
22k
R866 1k
R867 1k
R868 1k
R869 1k
R870 1k
10p R873 330
X802
32.768kHz
RADIO
TU-CE
TAPE
TU-DATA
TU-CLK
TU-MUTE
BEEP-H/L
VDD
TX
TEX
NC
ISS-1
ISS-2
TU-COUNT
TC-REC
TC-
SYSTEM CONTROLLER
IC801
CXP83624-027Q
COM2
COM1
COM0
VLC1
VLC2
VLC3
VL
VSS
XTAL
EXTAL
RST
SHIFT CLK
INIT
SIMUKE CHECK
JOG-A
JOG-B
R828
0
R830
R829
R826
R825
R832
1k
1k
1k
1k
1k
C886
22p
C887
10p
C882
10p
R884 R883
47k 1k
C830
0.1
Q804
2SC2413TKT146-N
C888 22p
C889 5p
C884 5p
C883 22p
Q803
2SC2413TKT146-N
C890
0.01
R882
1k
R881
10k
C885
0.001
R880
1k
PLAY
C881
22p
R871
1k
Q803,804
SHIFT CLOCK
CNP802
6P
JOG-A
R824
1k
JOG-B
KEY2
KEY1
R823
1k
GND
OPR/BATT
(Page 33)
R896
47k
R891
10k
C880
0.01
C801
100p
C823 C824 C825 C826
100p 100p 100p 100p
R895
47k
R431
4.7k
C431
0.001
Q431
DTC114YKA-T146
BUZZER H/L
CONTROL
R432
470
(Page 30)
C813
100p
R886
470k
R899
330k
CN801
2P
S901
(CD LID OPEN/CLOSE)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• A : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
[ ] : CD PLAY
〈〈 〉〉 : TAPE PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
31
31

CFD-E75L
6-14. PRINTED WIRING BOARDS – PANEL Section – • See page 23 for Circuit Boards Location.
KEY VOLUME BOARD
JOG BOARD
S401 – 413
RE401
ROTARY ENCODER
(JOG DAIL)
CN404 CN403
KEY POWER BOARD
1 3
R422
S413
MODE
S406 S407
DSPL
ENT MEM
MENU
ALARM
(Page 29)
E
JW401
S412
R413
MEGA BASS
OPR/BATT LED BOARD
1-681-672-
13
(13)
MAIN BOARD
CNP802
CN401
JW402
S403
RADIO BAND
AUTO PRESET
JW404
R402
R403
VOLUME +
R412
S411
R411
VOLUME –
R410
S408
x
R409
CN402
1
2
JW403
R421
D401
13
(13)
D401
OPR/BATT
CNP402
R408
CNP401
R406
R405
R404
S404
m
–
TUNE
2
1
S402
STANDBY
JW405
S410
N X
S409
1-681-859-
S405
M
+
OPERATE
S401
1-681-674-
13
(13)
1-681-673-
13
(13)
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
32
32

CFD-E75L
6-15. SCHEMATIC DIAGRAM – PANEL Section –
RE401
ROTARY ENCODER
(JOG DIAL)
S407
MENU ALARM
CNP401
5P
CN404
2P
S406
DSPL
JOG-A
ENT MEM
JOG-B
GND
KEY1
KEY2
CN403
3P
CN401
6P
JOG-A
(Page 31)
D401
L-34SRDLK
OPR/BATT
JOG-B
KEY2
KEY1
GND
OPR/BATT
R421
220
R422
150
R408
1.5k
S401
S402
S403
S404
S405
OPERATE
R402
1.5k
STANDBY
R403
2.2k
RADIO BAND
AUTO PRESET
R404
3.3k
-
R405
4.7k
+
TUNE
CNP402
2P
R406
6.8k
KEY2
GND
CN402
2P
S408
S409
S410
S411
S412
S413
R409
2.2k
R410
3.3k
R411
4.7k
R412
6.8k
R413
15k
-
VOLUME
+
MEGA BASS
MODE
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• C : panel designation.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
33
33

JW903
C903
C904
C902
C901
C191
C291
R198
C292
JW908
JW910
C194
JW911
CFD-E75L
6-16. PRINTED WIRING BOARDS – POWER SUPPLY Section – • See page 23 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A
J301
i
BATY B BOARD
BACK-UP BOARD
POWER BOARD
R293
1
2
3
4
(L-CH)
(R-CH)
B
R903
R294
L290
JW927
JW926
C
D
E
TP902 TP903
1 2
DRY BATTERY
SIZE “D”
(IEC DESIGNATION)
6PCS. 9V
BATY A BOARD
1-681-677-
13
(13)
DRY BATTERY
SIZE “AA”
(IEC DESIGNATION)
3PCS. 4.5V
TP904
2
1-681-678-
13
(13)
CNP901
D910
D909
D908
JW914
D907
CNP902
D904 D903 D902 D901
C293
C295
R291
C910
JW907
C195
C193
IC390
C294
R191
R190
C190
D394
C290
D392
C395
JW906
R290
C392
C192
R391
C296
R392
L190
JW913
D393
R393
R390
JW912
CNP392
Q391
C394
R394
JW909
C196 R296 R196
1
2
3
1
3
R298
R194
D391
Q291
L391
Q390
C391
R193
Q191
Q392
R396
R395
C399
R398
C398
Q393
C393
D390
R397
3
1
2
F
MAIN BOARD
CN322
(Page 29)
F
JW925 JW924
JW923
JW922
2
D913
JW921 JW926
C905
JW904
C397
R297
C297
R197
C197
JW901
C
MAIN BOARD
CN322
(Page 29)
D914
G
CN901
1
TP901
TP905
1-681-676-
13
AC INLET BOARD
CNP391
(13)
J901
~AC IN
TP911
T901
POWER TRANSFORMER
C911
H
TP914
F901
TP912
TP913
R901
C907
I
R902
C906
D905
D906
CN902
1-681-671-
1-681-679-
13
(13)
13
(13)
J
• Semiconductor Location
Ref. No.
Location
D390 D-18
D391 D-16
D392 D-15
D393 D-16
D394 C-15
D901 F-13
D902 F-12
D903 F-12
D904 F-12
D905 I-18
D906 I-18
D907 D-12
D908 D-12
Ref. No.
Location
D909 C-12
D910 C-12
D913 F-8
D914 G-8
IC390 D-14
Q191 E-17
Q291 E-17
Q390 D-17
Q391 D-16
Q392 D-17
Q393 C-18
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
34
34

R390
47
C291
C292
C192
C191
C397
47 10V
2200p
2200p
47 10V
220 10V
R290
R190
220
C290
220
C190
100p
100p
6-17. SCHEMATIC DIAGRAM – POWER SUPPLY Section –
CFD-E75L
POWER AMP
IC390
BA5417
CNP392
4P
(L-CH)
(R-CH)
R397
2.2k
C193
220
10V
C293
220
10V
C195
2200
10V
R193 R293
3.3k 3.3k
J301
C398
0.22
C296
1
50V
R194
100
L190
1µH
(Page 30)
R-OUT
A-GND
L-OUT
AU 6.2V
M/B-CONT
D390
1SS355TE-17
R296
470
Q291
KTC3198GR-AT
Q191,291
MEGA BASS
CONTROL
R196
470
Q191
KTC3198GR-AT
C297
0.47
50V
C197
0.47
50V
R398
470k
C399
22
25V
R298
1k
R297
15k
R198
1k
R197
15k
Q390
KTC2026Y
D392
UDZ-TE-17
-6.8B
C393
100
10V
+6.2V
REGULATOR
C196
1
50V
Q391
KTC2026Y
CD +6.2V
REGULATOR
D393
MTZJ-6.8B
R391
100
C392
220
10V
R393
10
C391
0.01
R392
150
C395
220
10V
D391
1SS355TE
-17
C394
0.01
R394
150
D394
1SS355TE
-17
C194
C294
0.022 0.022
R191
R291
2.2
2.2
Q393
DTC114EKA-T146
POWER ON/OFF
CONTROL
Q392
KTA1271Y-AT
B+ SWITCH
R395
1k
C911
10
50V
R396
47k
C910
4700
16V
C902
1
C904
1
C295
2200
10V
C906
0.1
D906
1SS355TE-17
C907
0.1
D905
1SS355TE-17
D902
2A02M
D904
2A02M
R901
100
R902
100
D907
1SS355TE
-17
D901
2A02M
D903
2A02M
C901
1
C903
1
R294
100
L391
1µH
C905
0.1
L290
1µH
F901
2.5A
250V
T901
POWER TRANSFORMER
CNP901
3P
CNP902
3P
D914
1SS355TE-17
D913
1SS355TE-17
CN902
3P
J901
~AC IN
MOT-GND
TC 9.0V
P-CON
COM VCC
R903
1
D908
UDZ-TE-17-2.7B
D909
1SS355TE-17
CN901
3P
(Page 30)
AC-HI
CD 6.2V
D-GND
S-GND
CNP391
10P
D910
RB441Q-40-T77
DRY BATTERY
SIZE"D"
(IEC DESIGNATION R20)
6PCS. 9V
(FOR POWER SUPPLY)
DRY BATTERY
SIZE"AA"
(IEC DESIGNATION R6)
3PCS. 4.5V
(FOR BACK-UP)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• 5 : fusible resistor.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Signal path.
F : AUDIO
35
35

+
–
+
–
+
–
–
+
–
+
+
–
+
–
–
+
+
–
CFD-E75L
• IC Block Diagrams
– CD Board –
IC701
LC78645NE
IC702
BA6998FP
LDD
LDS
FR
VVDD
PCKIST
VVSS
PDO2
PDO1
CONT1
CONT2
CONT3
VSS
VDD5
DRF
*RES
*WRQ
DO
DI
CL
CE
GND
OUT4-B
OUT4-A
IN4
IN4'
VREFIN
VCC
VCC
IN3'
IN3
OUT3-A
OUT3-B
NC
OPIN-B
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
APC
PLL VCEC
DRF
COMMAND INTERFACE
28 27 26 25 24 23 22 21 20 19 18 17 16 15
DRIVE
DRIVE
BUFFER
VCC VCC
BUFFER
CLV, CAV
CONTROL
LEVEL
SHIFT
LEVEL
SHIFT
SLCO
SLCIST
EFMIN
1
2
3
SLICE LEVEL
CONTROL
RUPTURE
DEFECT
RF
RFVDD
RFVSS
FIN1
FIN2
TIN1
4
5
6
7
8
9
TIN2 10
VREF 11
+
–
+
–
LEVEL SET
–
+
+
TBAL
TBAL
MIX EQ AGC
LPF
+
+ LPF
–
LPF
AUTO
ADJUST
PH
BH
SW
VREF
+
–
+
–
+
–
RAM
SERVO
PROCESSOR
INTERPOLATION
MUTE
ATTENUATION
DEEMPHASIS
RAM
SERIAL
OUT
EXTERNAL
AUDIO IN
60
59
58
57
56
55
DATA
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
54 16MOUT
LEVEL
SHIFT
DRIVE
DRIVE
BUFFER
BUFFER
1 2 3 4 5 6 7 8 9 10 11 12 13 14
OUT1-B
LEVEL
SHIFT
OUT1-A
IN1
RESET
REG-B
REGOUT
REGULATOR VOLTAGE DETECT,
BIAS VOLTAGE DETECT,
THERMAL SHUT DOWN
MUTE
GND
DRIVER
MUTING
IN2'
IN2
OUT2-A
OUT2-B
GND
OPOUT
REF1 12
FE
TEC
TE
RFMON
13
14
15
16
JITTC 17
ADAVDD 18
ADAVSS 19
TDO 20
A/D
VREF
S/H D/A SW
GENERAL-PURPOSE
PORTS
MONITOR
CONTROL
JITTER
DETECT
FRAME SYNC
DETECT,
PROTECT INSERT,
EFM DECODE
SUBCODE
DECODE CRC
MONITOR SIGNAL SELECTOR
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
FDO
SPDO
SLDO
GPDAC
CONT4
CONT5
SBCK/CONT6
SBCK/FG
V/*P
DEFECT
FSEQ
MONI1
TRACK
JUMP
MONI2
MONI3
MONI4
MONI5
ERROR
CORRECTION
AUDIO CD
C1-2, C2-2
8FS
DIGITAL FILTER
1BIT DAC
VSS
VDD
CLOCK
GENERATOR
AUDIO
OUT
BOUT
TEST
LPF
53 EFLG
52 C2F
51
50
49
48
47
46
45
44
43
42
41
XVSS
FSX/16MIN
XIN
XOUT
XVDD
RVDD
RCHO
RVSS
LVSS
LCHO
LVDD
– TUNER Board –
IC1
RF GND
TA2149N
1
FM RFIN 2
AM LOW CUT 3
MIX OUT
VCC
AM IF IN
FM IF IN
4
5
6
7
FM RF
FM
MIX
AM IF
FM IF
AM
MIX
LEVEL
DET
1/8
BUFF
FM
OSC
IF BUFF
1/1 OR
1/16
BUFF
ST
SW
AM
OSC
24
23
22
21
20
19
18
FM RFOUT
RF VCC
AM RFIN
FM OSC
AM OSC
OSC OUT
ST LED
GND 8
AGC 9
QUAD 10
AGC
AM
DET
FM
DET
AF BUFF
IF REQ
AF
17
16
15
IF REQ
DET OUT
MPX IN
R-OUT 11
L-OUT 12
MUTE
ST/MO
FM/AM
VCO
DIVIDE
DECODE
14
13
LPF1
LPF2
36
36

37
CFD-E75L
IC2
LC72137M-TLM
– TC Board –
IC301
TA2068N
11
10
9
8
7
6
5
4
3
2
1
12
13
14
15
16
19
20
UNLOCK
DETECTOR
POWER ON
RESET
UNIVERSAL
COUNTER
CCB
I/F
CE
DI
CL
DO
XOUT
AOUT
XIN
AIN
PD
VSS
VDD
B04
FMIN
AMIN
B01
B02
B03
I01
I02
IFIN
PHASE
DETECTOR
CHARGE
PUMP
REFERENCE
DIVIDER
SWALLOW
COUNTER
1/16,1/17
4BITS
12BITS
PROGRAMMABLE
DIVIDER
DATA SHIFT REGISTER
LATCH
1/2
17
18
1
2
3
6
9
10
11
12
8
7
4
5
22
TAPE
TAPE
TAPE
BUF AMP
A1
BUF AMP
A2
NAB
AMP1
NAB
AMP2
23
24
15
14
13
21
20
17
16
RADIO
BUF AMP
B1
BUF AMP
B2
MUTE
MUTE
ON
ON
ON
7dB
26dB
26dB
MONITOR
AMP
LOGIC
18
19
MUTE
7dB
MONITOR
AMP
LINE
TAPE
RADIO
LINE
ALC2 ALC1
DET
REC
AMP1
REC
AMP2
2.1
REF
AMP
MIC
AMP1
LINE
IN1
INT
EXT
RADIO
IN1
REC
PLAY
PRE
OUT1
PRE
OUT2
RADIO
LINE
RADIO
IN2
LINE
IN2
MIC
IN
TAPE
TAPE
VCC
ALC
NAB
OUT1
NAB
NF1
REC
OUT1
NAB
IN1
VREF
GND
NAB
IN2
REC
OUT2
NAB
NF2
NAB
OUT2
MIC
NF

CFD-E75L
6-18. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC801 CXP83624-027Q (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 CD-WRQ I Interruption detection signal input from the LC78645NE (IC701)
2 RMC I Sircs remote control signal input from the remote control receiver (IC804)
3 BUZZER O Buzzer sound signal output
4 N.C O Not used (open)
5 CD-RES O System reset signal output to the LC78645NE (IC701) “L”: reset
6 CD CE O Chip enable signal output to the LC78645NE (IC701)
7 CD CL O Serial data transfer clock signal output to the LC78645NE (IC701)
8 CD DO I Serial data input from the LC78645NE (IC701)
9 CD DI O Serial data output to the LC78645NE (IC701)
10 CD DRF I Focus on/off detection signal input from the LC78645NE (IC701)
11 CD FSEQ I Synchronizing signal detection signal input from the LC78645NE (IC701)
12 V-DATA O Serial data output to the electrical volume (IC320)
13 V-CLOCK O Serial data transfer clock signal output to the electrical volume (IC320)
14 N.C O Not used (open)
15 MEGABASS I Megabass on/off control signal output “L”: megabass on
16 A-MUTE O Audio muting on/off control signal output to the electrical volume (IC320) “H”: muting on
17 N.C O Not used (open)
18 CD O
Power on/off control signal output for the CD +5V power supply, and CD function control signal
output to the TA2068N (IC301) “H”: CD power on (CD on)
19 P-CON O
Power on/off control signal output to the power supply circuit, and power amplifier (IC390)
“L”: standby mode, “H”: power on
20 CD DOOR I CD lid open/close detection switch (S901) input terminal “H”: CD lid is closed
21 REG CHK I Regulator check signal input of the AC input or battery input “H” active
22 N.C O Not used (open)
23 KEY-1 I
Key input terminal (A/D input) S401 to S406 (OPERATE, STANDBY, RADIO BAND AUTO
PRESET, TUNE m –, TUNE M +, DSPL ENT MEM) keys input
24 KEY-2 I
Key input terminal (A/D input) S407 to S413 (MENU ALARM, x, u, VOLUME –,
VOLUME +, MEGA BASS, MODE) keys input
25 JOG-B I Jog dial pulse input from the rotary encoder (RE401 JOG DIAL) (B phase input)
26 JOG-A I Jog dial pulseinput from the rotary encoder (RE401 JOG DIAL) (A phase input)
27 SIMUKE CHECK I Destination setting terminal
28 INIT O Initial setting signal output
29 SHIFT CLK O Shift clock output of the main system clock (4.19 MHz) “H” active
30 RST I
System reset signal input from the reset signal generator (IC843) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31 EXTAL I Main system clock input terminal (4.19 MHz)
32 XTAL O Main system clock output terminal (4.19 MHz)
33 VSS — Ground terminal
34 VL O Liquid crystal display drive bias control signal output terminal
35 to 37 VLC3 to VLC1 — Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage
38 to 41 COM0 to COM3 O Common drive signal output to the liquid crystal display (LCD801)
42 to 61 SEG0 to SEG19 O Segment drive signal output to the liquid crystal display (LCD801)
62 to 64 N.C O Not used (open)
65 RADIO O Power on/off control signal output for the radio +6V power supply “H”: radio power on
66 TU-CE O PLL chip enable signal output to the FM/AM PLL (IC2)
38

CFD-E75L
Pin No. Pin Name I/O Description
67 TAPE O
Tape function control signal output to the TA2068N (IC301)
“L”: radio or CD on, “H”: tape on
68 TU-DATA O PLL serial data output to the FM/AM PLL (IC2)
69 TU-CLK O PLL serial data transfer clock signal output to the FM/AM PLL (IC2)
70 TU-MUTE O Tuner muting on/off control signal output to the FM/AM PLL (IC2) “H”: muting on
71 BEEP-H/L O Beep level H/L control signal output “L”: low, “H”: high
72 VDD — Power supply terminal (+5V)
73 TX O Sub system clock output terminal (32.768 kHz)
74 TEX I Sub system clock input terminal (32.768 kHz)
75 NC O Not used (open)
76 ISS-1 O ISS 1 on/off control signal output “H”: ISS 1 on
77 ISS-2 O ISS 2 on/off control signal output “H”: ISS 2 on
78 TU-COUNT I PLL serial count data input from the FM/AM PLL (IC2)
79 TC-REC I Record/playback detection signal input “L”: playback mode, “H”: recording mode
80 TC-PLAY I Tape play detection switch (S304) input terminal “L”: tape play mode
39

CFD-E75L
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts Color Cabinet's Color
7-1. CABINET SECTION
9
6 5
#1
7
8
4
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they The components identified by
3
CABINET UPPER SECTION
2
1
are seldom required for routine service. Some mark 0 or dotted line with mark
delay should be anticipated when ordering 0 are critical for safety.
Replace only with part number
these items.
specified.
• The mechanical parts with no reference number
in the exploded views are not supplied. • Abbreviation
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
EE : East European model
10
#2
#2
#4
#3
CABINET FRONT SECTION
#1
CABINET LOWER SECTION
#1
#2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-229-988-01 KNOB (REC)
2 3-229-987-01 KNOB (PLAY)
3 3-229-985-01 KNOB (REW)
4 3-229-986-01 KNOB (FF)
5 3-229-984-01 KNOB (STOP/EJECT)
8 1-452-899-11 MAGNET
9 3-234-540-01 CD LID (WHITE)...(WHITE)
9 3-234-540-11 CD LID (BLUE)...(BLUE)
9 3-234-540-21 CD LID (ORANGE)...(ORANGE)
10 3-229-996-31 HANDLE (WHITE)...(WHITE)
6 3-230-316-01 KNOB (PAUSE)
7 3-019-395-01 PLATE, CHUCKING
10 3-229-996-41 HANDLE (BLUE)...(BLUE)
10 3-229-996-51 HANDLE (ORANGE)...(ORANGE)
40

CFD-E75L
7-2. CABINET UPPER SECTION
59
60
61
62
57
58
#1
S901
56
55
76
74
not
supplied
81
80
53
not
supplied
82
64
78
80
OPTICAL
PICK-UP
SECTION
66
67
68
68
66
74
54
74
52
74 74
65
74
70
71
70
72
73
#5
#1
75
#1
51
#1
#1
79
#1
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 51 A-3062-464-A MAIN BOARD, COMPLETE
52 3-229-981-01 COVER PLATE
* 53 1-681-672-13 JOG BOARD
54 3-229-997-01 BUTTON (MENU)
55 3-229-998-01 BUTTON (PRESET)
66 3-038-948-01 RUBBER, VIBRATION PROOF
67 3-923-736-01 COVER, CD
68 3-038-948-11 RUBBER, VIBRATION PROOF
70 3-921-725-11 SCREW (2.6X10), +PWH
71 1-792-684-11 WIRE (FLAT TYPE) (16 CORE)
* 56 1-681-673-13 KEY POWER BOARD
57 X-3380-864-1 BUTTON POWER ASSY
58 3-229-972-01 DIAL JOG
59 3-922-112-31 DAMPER
60 3-229-994-31 CABINET UPPER (WHITE)...(WHITE)
60 3-229-994-41 CABINET UPPER (BLUE)...(BLUE)
60 3-229-994-51 CABINET UPPER (ORANGE)...(ORANGE)
61 3-232-770-01 STOPPER (CD)
62 3-229-968-01 CD SPRING
64 3-230-000-01 BUTTON (VOLUME)
* 65 1-681-674-13 KEY VOLUME BOARD
* 72 1-757-968-11 FFC CABLE 14P
* 73 A-3347-089-A CD BOARD, COMPLETE
74 4-951-620-11 SCREW (2.6X10), +BVTP
* 75 A-3062-465-A TUNER BOARD, COMPLETE
* 76 1-681-859-13 OPR/BATT LED BOARD
78 3-229-980-01 BUTTON CD
79 3-233-472-01 COVER, SPEAKER
80 3-233-666-01 CUSHION
81 1-682-105-11 BRACKET PWB (A)
82 1-682-106-11 BRACKET PWB (B)
S901 1-692-960-11 SWITCH, PUSH (1 KEY) (CD LID OPEN/CLOSE)
41

CFD-E75L
7-3. CABINET FRONT SECTION
104
105
LCD801
102
#3
108
107
103
101
117
112
111
116
106
107
#6
110
#5
#5
113
109 116
114
116
115
TAPE DECK SECTION
(MF-V5-117)
116
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 1-757-967-11 FFC CABLE 27P
102 3-229-989-01 HOLDER LCD
* 103 1-681-675-13 LCD BOARD
104 3-229-993-01 SPRING CASSETTE
105 3-229-990-31 HOLDER CASSETTE (WHITE)...(WHITE)
109 3-343-248-01 DAMPER (P), SMALL
110 3-222-726-01 CHASSIS (TC)
* 111 1-757-969-11 FFC CABLE 13P
* 112 A-3347-189-A TC BOARD, COMPLETE
113 3-231-847-01 LEVER (REC)
105 3-229-990-41 HOLDER CASSETTE (BLUE)...(BLUE)
105 3-229-990-51 HOLDER CASSETTE (ORANGE)...(ORANGE)
106 3-229-992-01 WINDOW CASSETTE (for ORANGE)
106 3-229-992-11 WINDOW CASSETTE (for WHITE, BLUE)
107 3-230-319-01 TAPE (CST WINDOW), DOUBLE-FACE
108 3-229-991-31 LID CASSETTE (WHITE)...(WHITE)
108 3-229-991-41 LID CASSETTE (BLUE)...(BLUE)
108 3-229-991-51 LID CASSETTE (ORANGE)...(ORANGE)
114 4-951-620-01 SCREW (2.6X8), +BVTP
115 X-3380-591-1 CABINET FRONT SUB ASSY
(includes speaker L/R) (for WHITE, BLUE)
115 X-3380-691-1 CABINET FRONT SUB ASSY
(includes speaker L/R) (for ORANGE)
116 3-233-633-01 SHEET, PE FOAM
117 3-232-615-01 SHIELD PAPER
LCD801 1-804-401-11
DISPLAY PANEL, LIQUID CRYSTAL
42

CFD-E75L
7-4. CABINET LOWER SECTION
158
#1 #1
161
159
163
T901
not
supplied
160
162
156
ANT1
#8
#8
not supplied
not supplied
164
157
165
not supplied
156
155
166
#1
153
154
166
152
#7
not supplied
151
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 3-229-970-01 LID BATTERY (for WHITE, BLUE)
151 3-229-970-11 LID BATTERY (for ORANGE)
152 3-232-533-01 FOOT RUBBER
153 3-229-971-01 CASE BATTERY
154 3-229-976-01 SPRING BATTERY (S) (–)
* 155 1-681-678-13 BACK-UP BOARD
156 3-229-975-01 SPRING BATTERY (–)
* 157 1-681-677-13 BATY B BOARD
* 158 A-3062-357-A POWER BOARD, COMPLETE
159 3-232-530-01 PLATE SHIELD (TRANS)
160 3-232-531-01 ADHESIVE SHEET (TRANS)
* 161 1-681-679-13 AC INLET BOARD
162 3-229-982-01 SPRING BATTERY (+–)
* 163 1-681-676-13 BATY A BOARD
164 3-229-974-01 ANTENNA TREMINAL
165 3-231-491-01 CABINET LOWER (WHITE)...(WHITE)
(EXCEPT EE, CIS)
165 3-231-491-11 CABINET LOWER (BLUE)...(BLUE)
(EXCEPT EE, CIS)
165 3-231-491-21 CABINET LOWER (ORANGE)...(ORANGE)
(EXCEPT EE, CIS)
165 3-231-491-31 CABINET LOWER (WHITE)...(WHITE) (EE, CIS)
165 3-231-491-41 CABINET LOWER (BLUE)...(BLUE) (EE, CIS)
165 3-231-491-51 CABINET LOWER (ORANGE)...(ORANGE)
(EE, CIS)
166 3-233-760-01 CUSHION, PU
ANT1 1-754-191-11 ANTENNA, TELESCOPIC
0 T901 1-437-320-11 TRANSFORMER, POWER
43

CFD-E75L
7-5. OPTICAL PICK-UP SECTION
(KSM-213CDP)
not supplied
501
not supplied
504
502
505
503
M701
M702
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
0 501 8-848-483-05 PICK-UP, OPTICAL KSS-213C/Q-RP
502 3-713-786-51 SCREW +P 2X3
503 2-626-908-01 SHAFT, SLED
504 2-627-003-01 GEAR (B) (RP)
505 X-2646-381-1 CHASSIS ASSY (MB), MOTOR (SPINDLE)
(including M701)
M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED)
44

CFD-E75L
7-6. TAPE MECHANISM DECK SECTION-1
(MF-V5-117)
HRP301
709
720
HE301
708
710
711
719
712
713
714
705
707
718
715
706
717
704
703
701
716
702
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
701 3-933-010-01 SPRING (S/P), TORSION
702 3-933-025-01 SPRING (P), TORSION
703 3-040-857-01 LEVER (P)
704 3-934-024-01 ROLLER, PINCH
705 3-933-019-01 SPRING (F/R), TORSION
* 712 3-008-587-01 SLIDER (STOP)
* 713 3-008-591-01 SLIDER (PAUSE)
714 3-933-004-01 CLAW, REEL
* 715 3-933-021-01 SLIDER (FRP)
* 716 3-933-006-01 SLIDER (EJECT)
706 3-933-028-01 SPRING (FWD), TORSION
707 3-933-016-01 GEAR (S REEL)
708 3-008-590-01 SLIDER (REC)
709 3-008-592-01 BASE (H), HEAD
* 710 3-008-588-01 SLIDER (REW)
717 3-934-833-01 SPRING (FRP)
718 3-022-794-02 SPRING (BT)
719 3-933-007-01 PLATE, LOCK
* 720 3-012-114-01 LEVER (FR)
HE301 1-543-876-11 HEAD (ERASE)
* 711 3-008-589-13 SLIDER (FF)
HRP301 1-500-668-11
HEAD,MAGNETIC (RECORD/PLAYBACK)
45

CFD-E75L
7-7. TAPE MECHANISM DECK SECTION-2
(MF-V5-117)
757
770
756
758
759
754
755
760
753
769
#10
761
S304
768
S303
762
M301
763
767
764
752
751
#9
765
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
751 3-933-029-01 LEVER, ERASING PREVENTION
752 3-933-182-01 SPRING, CASSETTE
753 3-932-995-01 GEAR (MID)
754 X-3371-667-1 CLUTCH ASSY
755 3-932-997-01 GEAR (CAM)
763 3-932-993-01 CHASSIS, OUTSERT
764 3-343-358-01 RING, RETAINING
765 3-223-156-01 SPRING (CAM), COMPRESSION
767 3-937-760-01 SPRING (GROUND), COMPRESSION
768 3-934-336-01 BEARING
* 756 3-932-999-01 SLIDER (SW)
757 3-932-998-01 SPRING (GROUND), TORSION
758 3-009-648-01 LEVER (S.OFF)
759 3-936-438-01 LEVER (K)
760 X-3373-572-1 REEL ASSY (N), T
761 3-933-020-11 BELT
762 X-3377-877-2 FLYWHEEL ASSY
769 3-939-383-02 SPRING, COMPRESSION
770 3-009-650-02 SPRING (K), COMPRESSION
M301 A-3320-446-A MOTOR ASSY (WITH PULLEY)
(CAPSTAN/REEL)
S303 1-762-679-11 SWITCH, LEAF (MOTOR ON/OFF)
S304 1-771-059-11 SWITCH, LEAF (TAPE PLAY)
46

NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified
in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
SECTION 8
ELECTRICAL PARTS LIST
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering
these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
AC INLET
BACK-UP
BATY B
CFD-E75L
BATY A
CD
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
• Abbreviation
EE : East European model
IT : Italian model
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-681-679-13 AC INLET BOARD
**************
< JACK >
0 J901 1-526-818-11 INLET, AC (-AC IN)
**************************************************************
* 1-681-678-13 BACK-UP BOARD
**************
3-229-976-01 SPRING BATTERY (S) (–)
3-815-381-01 CUSHION
3-831-441-99 SPACER
**************************************************************
C716 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C717 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C720 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C721 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C722 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C723 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C724 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C725 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C726 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C727 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C728 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C729 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C730 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
* 1-681-676-13 BATY A BOARD
*************
3-229-975-01 SPRING BATTERY (–)
< DIODE >
D913 8-719-988-61 DIODE 1SS355TE-17
D914 8-719-988-61 DIODE 1SS355TE-17
**************************************************************
* 1-681-677-13 BATY B BOARD
*************
3-229-975-01 SPRING BATTERY (–)
**************************************************************
* A-3347-089-A CD BOARD, COMPLETE
*******************
< CAPACITOR >
C701 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C702 1-104-664-11 ELECT 47uF 20% 10V
C703 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C704 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C705 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C706 1-126-960-11 ELECT 1uF 20% 50V
C707 1-115-156-11 CERAMIC CHIP 1uF 10V
C708 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C709 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C711 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C712 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C713 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C731 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C732 1-104-665-11 ELECT 100uF 20% 10V
C733 1-104-665-11 ELECT 100uF 20% 10V
C734 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C735 1-126-916-11 ELECT 1000uF 20% 6.3V
C736 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C740 1-126-935-11 ELECT 470uF 20% 10V
C741 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C742 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C743 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C744 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C745 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C746 1-104-665-11 ELECT 100uF 20% 10V
C747 1-104-665-11 ELECT 100uF 20% 10V
C750 1-104-665-11 ELECT 100uF 20% 10V
C751 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C754 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C755 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< CONNECTOR >
* CNP701 1-779-466-11 CONNECTOR, FFC/FPC 16P
* CNP702 1-784-736-11 CONNECTOR, FFC 14P
< FERRITE BEAD >
FB701 1-469-701-21 FERRITE 0uH
< IC >
IC701 6-700-455-01 IC LC78645NE
IC702 8-759-591-62 IC BA6998FP
47

CFD-E75L
CD JOG KEY POWER KEY VOLUME
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR >
JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
JC702 1-216-864-11 METAL CHIP 0 5% 1/16W
JC703 1-216-864-11 METAL CHIP 0 5% 1/16W
JC704 1-216-813-11 METAL CHIP 220 5% 1/16W
* 1-681-672-13 JOG BOARD
**********
< ROTARY ENCODER >
RE401 1-476-747-11 ENCODER (JOG DIAL)
< FERRITE BEAD >
L706 1-414-445-11 FERRITE 0uH
< TRANSISTOR >
Q701 8-729-054-57 TRANSISTOR KTN2907AS-RTK
< RESISTOR >
R701 1-216-841-11 METAL CHIP 47K 5% 1/16W
R702 1-216-835-11 METAL CHIP 15K 5% 1/16W
R703 1-216-835-11 METAL CHIP 15K 5% 1/16W
R704 1-216-835-11 METAL CHIP 15K 5% 1/16W
R705 1-216-835-11 METAL CHIP 15K 5% 1/16W
R706 1-216-841-11 METAL CHIP 47K 5% 1/16W
R707 1-216-797-11 METAL CHIP 10 5% 1/16W
R708 1-216-833-11 METAL CHIP 10K 5% 1/16W
R709 1-216-837-11 METAL CHIP 22K 5% 1/16W
R710 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R711 1-216-815-11 METAL CHIP 330 5% 1/16W
R712 1-216-809-11 METAL CHIP 100 5% 1/16W
R714 1-216-811-11 METAL CHIP 150 5% 1/16W
R715 1-216-811-11 METAL CHIP 150 5% 1/16W
R716 1-216-821-11 METAL CHIP 1K 5% 1/16W
R717 1-216-821-11 METAL CHIP 1K 5% 1/16W
R718 1-216-821-11 METAL CHIP 1K 5% 1/16W
R719 1-216-809-11 METAL CHIP 100 5% 1/16W
R720 1-216-809-11 METAL CHIP 100 5% 1/16W
R721 1-216-821-11 METAL CHIP 1K 5% 1/16W
R722 1-216-809-11 METAL CHIP 100 5% 1/16W
R723 1-216-809-11 METAL CHIP 100 5% 1/16W
R724 1-216-841-11 METAL CHIP 47K 5% 1/16W
R725 1-216-819-11 METAL CHIP 680 5% 1/16W
R726 1-216-819-11 METAL CHIP 680 5% 1/16W
R727 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R728 1-216-833-11 METAL CHIP 10K 5% 1/16W
R729 1-216-813-11 METAL CHIP 220 5% 1/16W
R730 1-216-821-11 METAL CHIP 1K 5% 1/16W
R731 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R741 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R743 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R744 1-216-845-11 METAL CHIP 100K 5% 1/16W
< SWITCH >
S701 1-762-812-11 SWITCH, LEAF (LIMIT)
< VIBRATOR >
X701 1-795-173-21 VIBRATOR, CERAMIC (33.868MHz)
**************************************************************
< SWITCH >
S406 1-762-798-11 SWITCH, KEYBOARD (DSPL, ENT MEM)
S407 1-762-798-11 SWITCH, KEYBOARD (MENU, ALARM)
**************************************************************
* 1-681-673-13 KEY POWER BOARD
*****************
< CONNECTOR >
* CNP401 1-785-657-11 PIN, CONNECTOR (PC BOARD) 5P
* CNP402 1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P
< RESISTOR >
R402 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R403 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R404 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R405 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R406 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R408 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R422 1-216-811-11 METAL CHIP 150 5% 1/16W
< SWITCH >
S401 1-762-798-11 SWITCH, KEYBOARD (OPERATE)
S402 1-762-798-11 SWITCH, KEYBOARD (STANDBY)
S403 1-762-798-11 SWITCH, KEYBOARD
(RADIO BAND, AUTO PRESET)
S404 1-762-798-11 SWITCH, KEYBOARD (TUNE m –)
S405 1-762-798-11 SWITCH, KEYBOARD (TUNE M +)
**************************************************************
* 1-681-674-13 KEY VOLUME BOARD
******************
< RESISTOR >
R409 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R410 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R411 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R412 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R413 1-216-835-11 METAL CHIP 15K 5% 1/16W
< SWITCH >
S408 1-762-798-11 SWITCH, KEYBOARD (x)
S409 1-762-798-11 SWITCH, KEYBOARD (u)
S410 1-762-798-11 SWITCH, KEYBOARD (VOLUME –)
S411 1-762-798-11 SWITCH, KEYBOARD (VOLUME +)
S412 1-762-798-11 SWITCH, KEYBOARD (MEGA BASS)
S413 1-762-798-11 SWITCH, KEYBOARD (MODE)
**************************************************************
48

CFD-E75L
LCD
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-681-675-13 LCD BOARD
**********
C820 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C823 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
3-229-989-01 HOLDER LCD
3-232-615-01 SHIELD PAPER
CNP811 1-784-788-11
< CONNECTOR >
CONNECTOR, FFC 27P
< IC >
IC804 8-749-018-72 IC SPS-442-E (REMOTE CONTROL RECEIVER)
< LIQUID CRYSTAL DISPLAY >
LCD801 1-804-401-11 DISPLAY PANEL, LIQUID CRYSTAL
**************************************************************
* A-3062-464-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
C120 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C123 1-126-960-11 ELECT 1uF 20% 50V
C124 1-126-960-11 ELECT 1uF 20% 50V
C125 1-126-960-11 ELECT 1uF 20% 50V
C126 1-126-960-11 ELECT 1uF 20% 50V
C127 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C220 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C223 1-126-960-11 ELECT 1uF 20% 50V
C224 1-126-960-11 ELECT 1uF 20% 50V
C225 1-126-960-11 ELECT 1uF 20% 50V
C226 1-126-960-11 ELECT 1uF 20% 50V
C227 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C320 1-104-665-11 ELECT 100uF 20% 10V
C321 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C322 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C323 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C324 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C325 1-126-934-11 ELECT 220uF 20% 10V
C326 1-104-665-11 ELECT 100uF 20% 10V
C327 1-126-934-11 ELECT 220uF 20% 16V
C328 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C329 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C330 1-104-665-11 ELECT 100uF 20% 10V
C331 1-104-664-11 ELECT 47uF 20% 10V
C332 1-104-665-11 ELECT 100uF 20% 10V
C334 1-126-964-11 ELECT 10uF 20% 50V
C335 1-126-961-11 ELECT 2.2uF 20% 50V
C351 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C431 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C801 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C802 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C803 1-104-664-11 ELECT 47uF 20% 10V
C805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C810 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C818 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C819 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C824 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C825 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C826 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C830 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C834 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C835 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C836 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C837 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C865 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C866 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C868 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C869 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C872 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C873 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C874 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C875 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C880 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C881 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C882 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C883 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C884 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C885 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C886 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C887 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C888 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C889 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C890 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C892 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< CONNECTOR >
CN322 1-785-665-11 PIN, CONNECTOR (PC BOARD) 13P
* CNP321 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P
* CNP322 1-784-774-21 CONNECTOR, FFC 13P
* CNP323 1-784-775-21 CONNECTOR, FFC 14P
CNP801 1-784-788-11 CONNECTOR, FFC 27P
* CNP802 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
D320 8-719-988-61 DIODE 1SS355TE-17
D321 8-719-988-61 DIODE 1SS355TE-17
D322 8-719-988-61 DIODE 1SS355TE-17
D323 8-719-988-61 DIODE 1SS355TE-17
D324 8-719-988-61 DIODE 1SS355TE-17
D325 8-719-988-61 DIODE 1SS355TE-17
D326 8-719-976-99 DIODE DTZ5.1B
D327 8-719-056-77 DIODE UDZ-TE-17-3.9B
D328 8-719-988-61 DIODE 1SS355TE-17
D329 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC320 8-759-539-45 IC M62429P
IC321 8-759-658-46 IC S-81233SGY-Z
IC801 8-752-921-85 IC CXP83624-027Q
IC803 8-759-645-87 IC PST9128-T
49

CFD-E75L
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< COIL >
L321 1-410-509-61 INDUCTOR 10uH
L322 1-414-142-61 INDUCTOR 1uH
L801 1-410-521-11 INDUCTOR 100uH
L802 1-414-146-31 INDUCTOR 2.2uH
R803 1-216-833-11 METAL CHIP 10K 5% 1/16W
R805 1-216-821-11 METAL CHIP 1K 5% 1/16W
R806 1-216-821-11 METAL CHIP 1K 5% 1/16W
R807 1-216-821-11 METAL CHIP 1K 5% 1/16W
R808 1-216-821-11 METAL CHIP 1K 5% 1/16W
< TRANSISTOR >
Q120 8-729-036-89 TRANSISTOR KTC3198GR-A
Q122 8-729-920-31 TRANSISTOR DTC343TK
Q220 8-729-036-89 TRANSISTOR KTC3198GR-A
Q222 8-729-920-31 TRANSISTOR DTC343TK
Q322 8-729-027-46 TRANSISTOR DTC114YKA-T146
Q323 8-729-027-26 TRANSISTOR DTA114YKA-T146
Q325 8-729-027-46 TRANSISTOR DTC114YKA-T146
Q326 8-729-037-13 TRANSISTOR KTA1271Y
Q327 8-729-212-02 TRANSISTOR 2SC2120-Y
Q328 8-729-027-26 TRANSISTOR DTA114YKA-T146
Q329 8-729-034-51 TRANSISTOR KTC3875
Q431 8-729-027-46 TRANSISTOR DTC114YKA-T146
Q803 8-729-930-97 TRANSISTOR 2SC2413KT146-N
Q804 8-729-930-97 TRANSISTOR 2SC2413KT146-N
< RESISTOR >
R120 1-216-821-11 METAL CHIP 1K 5% 1/16W
R121 1-216-849-11 METAL CHIP 220K 5% 1/16W
R122 1-216-813-11 METAL CHIP 220 5% 1/16W
R123 1-216-821-11 METAL CHIP 1K 5% 1/16W
R124 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R125 1-216-835-11 METAL CHIP 15K 5% 1/16W
R130 1-216-849-11 METAL CHIP 220K 5% 1/16W
R220 1-216-821-11 METAL CHIP 1K 5% 1/16W
R221 1-216-849-11 METAL CHIP 220K 5% 1/16W
R222 1-216-813-11 METAL CHIP 220 5% 1/16W
R223 1-216-821-11 METAL CHIP 1K 5% 1/16W
R224 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R225 1-216-835-11 METAL CHIP 15K 5% 1/16W
R230 1-216-849-11 METAL CHIP 220K 5% 1/16W
R320 1-216-811-11 METAL CHIP 150 5% 1/16W
R321 1-216-841-11 METAL CHIP 47K 5% 1/16W
R322 1-216-809-11 METAL CHIP 100 5% 1/16W
R323 1-216-833-11 METAL CHIP 10K 5% 1/16W
R324 1-216-821-11 METAL CHIP 1K 5% 1/16W
R325 1-216-811-11 METAL CHIP 150 5% 1/16W
R326 1-216-815-11 METAL CHIP 330 5% 1/16W
R327 1-247-807-31 CARBON 100 5% 1/4W
R328 1-247-807-31 CARBON 100 5% 1/4W
R329 1-216-821-11 METAL CHIP 1K 5% 1/16W
R330 1-216-845-11 METAL CHIP 100K 5% 1/16W
R331 1-216-809-11 METAL CHIP 100 5% 1/16W
R332 1-216-813-11 METAL CHIP 220 5% 1/16W
R333 1-216-817-11 METAL CHIP 470 5% 1/16W
R334 1-216-815-11 METAL CHIP 330 5% 1/16W
R335 1-216-815-11 METAL CHIP 330 5% 1/16W
R336 1-216-817-11 METAL CHIP 470 5% 1/16W
R431 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R432 1-216-817-11 METAL CHIP 470 5% 1/16W
R801 1-216-821-11 METAL CHIP 1K 5% 1/16W
R802 1-216-821-11 METAL CHIP 1K 5% 1/16W
R809 1-216-821-11 METAL CHIP 1K 5% 1/16W
R810 1-216-821-11 METAL CHIP 1K 5% 1/16W
R811 1-216-821-11 METAL CHIP 1K 5% 1/16W
R812 1-216-821-11 METAL CHIP 1K 5% 1/16W
R813 1-216-821-11 METAL CHIP 1K 5% 1/16W
R815 1-216-821-11 METAL CHIP 1K 5% 1/16W
R816 1-216-821-11 METAL CHIP 1K 5% 1/16W
R818 1-216-837-11 METAL CHIP 22K 5% 1/16W
R819 1-216-821-11 METAL CHIP 1K 5% 1/16W
R820 1-216-821-11 METAL CHIP 1K 5% 1/16W
R821 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R823 1-216-821-11 METAL CHIP 1K 5% 1/16W
R824 1-216-821-11 METAL CHIP 1K 5% 1/16W
R825 1-216-821-11 METAL CHIP 1K 5% 1/16W
R826 1-216-821-11 METAL CHIP 1K 5% 1/16W
R827 1-216-833-11 METAL CHIP 10K 5% 1/16W
R828 1-216-864-11 METAL CHIP 0 5% 1/16W
R829 1-216-821-11 METAL CHIP 1K 5% 1/16W
R830 1-216-821-11 METAL CHIP 1K 5% 1/16W
R832 1-216-821-11 METAL CHIP 1K 5% 1/16W
R834 1-216-839-11 METAL CHIP 33K 5% 1/16W
R835 1-216-845-11 METAL CHIP 100K 5% 1/16W
R836 1-216-845-11 METAL CHIP 100K 5% 1/16W
R837 1-216-845-11 METAL CHIP 100K 5% 1/16W
R838 1-216-841-11 METAL CHIP 47K 5% 1/16W
R839 1-216-841-11 METAL CHIP 47K 5% 1/16W
R840 1-216-841-11 METAL CHIP 47K 5% 1/16W
R841 1-216-841-11 METAL CHIP 47K 5% 1/16W
R842 1-216-841-11 METAL CHIP 47K 5% 1/16W
R843 1-216-841-11 METAL CHIP 47K 5% 1/16W
R844 1-216-841-11 METAL CHIP 47K 5% 1/16W
R845 1-216-841-11 METAL CHIP 47K 5% 1/16W
R846 1-216-841-11 METAL CHIP 47K 5% 1/16W
R847 1-216-841-11 METAL CHIP 47K 5% 1/16W
R848 1-216-841-11 METAL CHIP 47K 5% 1/16W
R849 1-216-841-11 METAL CHIP 47K 5% 1/16W
R850 1-216-841-11 METAL CHIP 47K 5% 1/16W
R851 1-216-841-11 METAL CHIP 47K 5% 1/16W
R852 1-216-841-11 METAL CHIP 47K 5% 1/16W
R853 1-216-841-11 METAL CHIP 47K 5% 1/16W
R854 1-216-841-11 METAL CHIP 47K 5% 1/16W
R855 1-216-841-11 METAL CHIP 47K 5% 1/16W
R856 1-216-841-11 METAL CHIP 47K 5% 1/16W
R857 1-216-841-11 METAL CHIP 47K 5% 1/16W
R858 1-216-841-11 METAL CHIP 47K 5% 1/16W
R859 1-216-841-11 METAL CHIP 47K 5% 1/16W
R860 1-216-841-11 METAL CHIP 47K 5% 1/16W
R861 1-216-841-11 METAL CHIP 47K 5% 1/16W
R865 1-216-837-11 METAL CHIP 22K 5% 1/16W
R866 1-216-821-11 METAL CHIP 1K 5% 1/16W
R867 1-216-821-11 METAL CHIP 1K 5% 1/16W
R868 1-216-821-11 METAL CHIP 1K 5% 1/16W
50

CFD-E75L
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R869 1-216-821-11 METAL CHIP 1K 5% 1/16W
R870 1-216-821-11 METAL CHIP 1K 5% 1/16W
R871 1-216-821-11 METAL CHIP 1K 5% 1/16W
R873 1-216-815-11 METAL CHIP 330 5% 1/16W
R876 1-216-821-11 METAL CHIP 1K 5% 1/16W
R877 1-216-821-11 METAL CHIP 1K 5% 1/16W
R878 1-216-821-11 METAL CHIP 1K 5% 1/16W
R879 1-216-845-11 METAL CHIP 100K 5% 1/16W
R880 1-216-821-11 METAL CHIP 1K 5% 1/16W
R881 1-216-833-11 METAL CHIP 10K 5% 1/16W
R882 1-216-821-11 METAL CHIP 1K 5% 1/16W
R883 1-216-821-11 METAL CHIP 1K 5% 1/16W
R884 1-216-841-11 METAL CHIP 47K 5% 1/16W
R886 1-216-853-11 METAL CHIP 470K 5% 1/16W
R888 1-216-851-11 METAL CHIP 330K 5% 1/16W
R890 1-216-851-11 METAL CHIP 330K 5% 1/16W
R891 1-216-833-11 METAL CHIP 10K 5% 1/16W
R892 1-216-833-11 METAL CHIP 10K 5% 1/16W
R893 1-216-845-11 METAL CHIP 100K 5% 1/16W
R894 1-216-845-11 METAL CHIP 100K 5% 1/16W
R895 1-216-841-11 METAL CHIP 47K 5% 1/16W
R896 1-216-841-11 METAL CHIP 47K 5% 1/16W
R899 1-216-851-11 METAL CHIP 330K 5% 1/16W
MAIN OPR/BATT LED POWER
C292 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C293 1-126-934-11 ELECT 220uF 20% 10V
C294 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C295 1-126-927-11 ELECT 2200uF 20% 10V
C296 1-126-960-11 ELECT 1uF 20% 50V
C297 1-126-959-11 ELECT 0.47uF 20% 50V
C391 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C392 1-126-934-11 ELECT 220uF 20% 10V
C393 1-104-665-11 ELECT 100uF 20% 10V
C394 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C395 1-126-934-11 ELECT 220uF 20% 10V
C397 1-126-934-11 ELECT 220uF 20% 10V
C398 1-165-128-11 CERAMIC CHIP 0.22uF 16V
C399 1-128-551-11 ELECT 22uF 20% 25V
C901 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C902 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C903 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C904 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C905 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C906 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C907 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C910 1-126-937-11 ELECT 4700uF 20% 16V
C911 1-126-964-11 ELECT 10uF 20% 50V
< VIBRATOR >
X801 1-767-184-11 VIBRATOR, CERAMIC (4.19MHz)
X802 1-767-697-11 VIBRATOR, CRYSTAL (32.768kHz)
**************************************************************
* 1-681-859-13 OPR/BATT LED BOARD
*******************
< LED >
D401 8-719-085-67 LED L-34SRDLK (OPR/BATT)
< RESISTOR >
R421 1-216-813-11 METAL CHIP 220 5% 1/16W
**************************************************************
* A-3062-357-A POWER BOARD, COMPLETE
***********************
1-533-233-31 HOLDER, FUSE
3-232-530-01 PLATE SHIELD (TRANS)
3-232-531-01 ADHESIVE SHEET (TRANS)
7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR >
C190 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C191 1-104-664-11 ELECT 47uF 20% 10V
C192 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C193 1-126-934-11 ELECT 220uF 20% 10V
C194 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C195 1-126-927-11 ELECT 2200uF 20% 10V
C196 1-126-960-11 ELECT 1uF 20% 50V
C197 1-126-959-11 ELECT 0.47uF 20% 50V
C290 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C291 1-104-664-11 ELECT 47uF 20% 10V
< CONNECTOR >
* CNP392 1-564-778-11 PLUG, CONNECTOR (2.5mm) 4P
* CNP901 1-785-655-21 PIN, CONNECTOR (PC BOARD) 3P
CNP902 1-569-596-11 PLUG, CONNECTOR (2.5mm) 3P
< DIODE >
D390 8-719-988-61 DIODE 1SS355TE-17
D391 8-719-988-61 DIODE 1SS355TE-17
D392 8-719-056-83 DIODE UDZ-TE-17-6.8B
D393 8-719-109-97 DIODE RD6.8ES-B2
D394 8-719-988-61 DIODE 1SS355TE-17
D901 8-719-046-07 DIODE 2A02M
D902 8-719-046-07 DIODE 2A02M
D903 8-719-046-07 DIODE 2A02M
D904 8-719-046-07 DIODE 2A02M
D905 8-719-988-61 DIODE 1SS355TE-17
D906 8-719-988-61 DIODE 1SS355TE-17
D907 8-719-988-61 DIODE 1SS355TE-17
D908 8-719-056-73 DIODE UDZ-TE-17-2.7B
D909 8-719-988-61 DIODE 1SS355TE-17
D910 8-719-050-84 DIODE RB441Q-40T-77
< FUSE >
0 F901 1-533-469-11 FUSE (2.5A/250V)
< IC >
IC390 8-759-426-51 IC BA5417
< JACK >
J301 1-566-891-11 JACK (i)
< COIL >
L190 1-414-142-61 INDUCTOR 1uH
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
51

CFD-E75L
POWER
TC
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
L290 1-414-142-61 INDUCTOR 1uH
L391 1-414-142-61 INDUCTOR 1uH
< TRANSISTOR >
Q191 8-729-036-89 TRANSISTOR KTC3198GR-A
Q291 8-729-036-89 TRANSISTOR KTC3198GR-A
Q390 8-729-052-52 TRANSISTOR KTC2026Y
Q391 8-729-052-52 TRANSISTOR KTC2026Y
Q392 8-729-037-13 TRANSISTOR KTA1271Y
Q393 8-729-900-53 TRANSISTOR DTC114EK
< RESISTOR >
R190 1-216-813-11 METAL CHIP 220 5% 1/16W
R191 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R193 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R194 1-216-809-11 METAL CHIP 100 5% 1/16W
R196 1-216-817-11 METAL CHIP 470 5% 1/16W
R197 1-216-835-11 METAL CHIP 15K 5% 1/16W
R198 1-216-821-11 METAL CHIP 1K 5% 1/16W
R290 1-216-813-11 METAL CHIP 220 5% 1/16W
R291 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R293 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R294 1-216-809-11 METAL CHIP 100 5% 1/16W
R296 1-216-817-11 METAL CHIP 470 5% 1/16W
R297 1-216-835-11 METAL CHIP 15K 5% 1/16W
R298 1-216-821-11 METAL CHIP 1K 5% 1/16W
R390 1-216-805-11 METAL CHIP 47 5% 1/16W
C204 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C206 1-126-960-11 ELECT 1uF 20% 50V
C207 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C301 1-104-665-11 ELECT 100uF 20% 10V
C302 1-104-665-11 ELECT 100uF 20% 10V
C303 1-104-665-11 ELECT 100uF 20% 10V
C304 1-104-664-11 ELECT 47uF 20% 10V
C305 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C307 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C308 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C310 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
CNP301 1-784-774-11
< CONNECTOR >
CONNECTOR, FFC 13P
< IC >
IC301 8-759-264-71 IC TA2068N
< RESISTOR >
JC301 1-216-864-11 METAL CHIP 0 5% 1/16W
JC302 1-216-864-11 METAL CHIP 0 5% 1/16W
JC303 1-216-864-11 METAL CHIP 0 5% 1/16W
JC304 1-216-864-11 METAL CHIP 0 5% 1/16W
< TRANSISTOR >
R391 1-216-809-11 METAL CHIP 100 5% 1/16W
R392 1-216-811-11 METAL CHIP 150 5% 1/16W
R393 1-216-797-11 METAL CHIP 10 5% 1/16W
R394 1-249-407-11 CARBON 150 5% 1/4W
R395 1-216-821-11 METAL CHIP 1K 5% 1/16W
R396 1-216-841-11 METAL CHIP 47K 5% 1/16W
R397 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R398 1-216-853-11 METAL CHIP 470K 5% 1/16W
R901 1-216-809-11 METAL CHIP 100 5% 1/16W
R902 1-216-809-11 METAL CHIP 100 5% 1/16W
0R903 1-219-149-11 FUSIBLE 1 5% 1/4W F
< TRANSFORMER >
0T901 1-437-320-11 TRANSFORMER, POWER
**************************************************************
* A-3347-189-A TC BOARD, COMPLETE
*******************
< CAPACITOR >
C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C102 1-104-664-11 ELECT 47uF 20% 10V
C103 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C104 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C106 1-126-960-11 ELECT 1uF 20% 50V
C107 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C202 1-104-664-11 ELECT 47uF 20% 10V
C203 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
Q301 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q302 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q303 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R101 1-216-835-11 METAL CHIP 15K 5% 1/16W
R102 1-216-807-11 METAL CHIP 68 5% 1/16W
R103 1-216-843-11 METAL CHIP 68K 5% 1/16W
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R105 1-216-835-11 METAL CHIP 15K 5% 1/16W
R106 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R110 1-216-809-11 METAL CHIP 100 5% 1/16W
R111 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R201 1-216-835-11 METAL CHIP 15K 5% 1/16W
R202 1-216-807-11 METAL CHIP 68 5% 1/16W
R203 1-216-843-11 METAL CHIP 68K 5% 1/16W
R204 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R205 1-216-835-11 METAL CHIP 15K 5% 1/16W
R206 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R210 1-216-025-11 RES-CHIP 100 5% 1/10W
R211 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R301 1-216-857-11 METAL CHIP 1M 5% 1/16W
R302 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R303 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R304 1-216-821-11 METAL CHIP 1K 5% 1/16W
R305 1-216-811-11 METAL CHIP 150 5% 1/16W
R306 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R307 1-216-799-11 METAL CHIP 15 5% 1/16W
R308 1-216-837-11 METAL CHIP 22K 5% 1/16W
R309 1-216-805-11 METAL CHIP 47 5% 1/16W
52
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.

CFD-E75L
TC
TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R310 1-216-857-11 METAL CHIP 1M 5% 1/16W
R311 1-216-857-11 METAL CHIP 1M 5% 1/16W
R312 1-216-821-11 METAL CHIP 1K 5% 1/16W
R313 1-216-821-11 METAL CHIP 1K 5% 1/16W
< SWITCH >
S301 1-786-126-11 SWITCH, SLIDE (REC/PB)
< TRANSFORMER >
T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION
**************************************************************
* A-3062-465-A TUNER BOARD, COMPLETE
**********************
< CAPACITOR >
C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C2 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C10 1-126-960-11 ELECT 1uF 20% 50V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C12 1-126-963-11 ELECT 4.7uF 20% 50V
C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C18 1-126-934-11 ELECT 220uF 20% 10V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C21 1-126-960-11 ELECT 1uF 20% 50V
C22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C23 1-126-960-11 ELECT 1uF 20% 50V
C24 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C25 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C29 1-104-665-11 ELECT 100uF 20% 10V
C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C31 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C54 1-126-934-11 ELECT 220uF 20% 10V
C55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C58 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C59 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C64 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C66 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C70 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C71 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C72 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C73 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C93 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
< CERAMIC FILTER >
CF2 1-579-185-21 FILTER, CERAMIC
CF4 1-781-962-21 FILTER, CERAMIC
< CONNECTOR >
* CNP1 1-785-663-11 PIN, CONNECTOR (PC BOARD) 11P
< TRIMMER >
CT1 1-141-603-11 CAP, ADJ 20PF
CT3 1-141-601-11 CAP, ADJ 10PF
CT5 1-141-622-11 CAP, ADJ 50PF
< DIODE >
D1 8-719-078-48 DIODE KV1471ETR1-3
D2 8-719-078-48 DIODE KV1471ETR1-3
D3 8-719-050-69 DIODE KV1520N
D10 8-719-988-61 DIODE 1SS355TE-17
D11 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC1 8-759-662-67 IC TA2149N
IC2 8-759-483-40 IC LC72137M-TLM
C40 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C41 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C43 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C44 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C45 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C46 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C48 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C49 1-161-772-11 CERAMIC 0.1uF 10% 25V
C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C53 1-137-194-81 FILM 0.47uF 5% 50V
< RESISTOR >
JC1 1-216-864-11 METAL CHIP 0 5% 1/16W
JC2 1-216-864-11 METAL CHIP 0 5% 1/16W
JC3 1-216-864-11 METAL CHIP 0 5% 1/16W
JC4 1-216-864-11 METAL CHIP 0 5% 1/16W
JC5 1-216-864-11 METAL CHIP 0 5% 1/16W
JC6 1-216-864-11 METAL CHIP 0 5% 1/16W
JC22 1-216-864-11 METAL CHIP 0 5% 1/16W
JC23 1-216-864-11 METAL CHIP 0 5% 1/16W
JC24 1-216-864-11 METAL CHIP 0 5% 1/16W
JC33 1-216-864-11 METAL CHIP 0 5% 1/16W
53

CFD-E75L
TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
JC34 1-216-864-11 METAL CHIP 0 5% 1/16W R94 1-216-821-11 METAL CHIP 1K 5% 1/16W
< COIL >
L1 1-409-775-11 COIL, AIR-CORE
L2 1-416-509-11 COIL, AIR-CORE
L3 1-754-116-11 ANTENNA, FERRITE-ROD (LW MW)
L4 1-411-199-31 COIL, MW/LW OSC
L21 1-410-509-61 INDUCTOR 10uH
< TRANSISTOR >
Q12 8-729-028-99 TRANSISTOR DTC114YUA-T106
Q14 8-729-905-35 TRANSISTOR 2SC4081-R
Q41 8-729-920-31 TRANSISTOR DTC343TK
Q42 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ
Q43 8-729-920-38 TRANSISTOR 2SC2059K-N
Q44 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ
Q61 8-729-106-07 FET 2SK514-H
< RESISTOR >
R1 1-216-817-11 METAL CHIP 470 5% 1/16W
R2 1-216-817-11 METAL CHIP 470 5% 1/16W
R3 1-216-833-11 METAL CHIP 10K 5% 1/16W
R4 1-216-833-11 METAL CHIP 10K 5% 1/16W
R7 1-216-853-11 METAL CHIP 470K 5% 1/16W
R9 1-216-845-11 METAL CHIP 100K 5% 1/16W
R10 1-216-805-11 METAL CHIP 47 5% 1/16W
R11 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R12 1-216-841-11 METAL CHIP 47K 5% 1/16W
R13 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R16 1-216-833-11 METAL CHIP 10K 5% 1/16W
R17 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R18 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R19 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R22 1-216-833-11 METAL CHIP 10K 5% 1/16W
R24 1-216-813-11 METAL CHIP 220 5% 1/16W
R30 1-216-835-11 METAL CHIP 15K 5% 1/16W
R31 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R32 1-216-845-11 METAL CHIP 100K 5% 1/16W
R40 1-216-853-11 METAL CHIP 470K 5% 1/16W
R41 1-216-833-11 METAL CHIP 10K 5% 1/16W
R42 1-216-845-11 METAL CHIP 100K 5% 1/16W
R43 1-216-833-11 METAL CHIP 10K 5% 1/16W
R50 1-216-821-11 METAL CHIP 1K 5% 1/16W
R51 1-216-833-11 METAL CHIP 10K 5% 1/16W
R52 1-216-809-11 METAL CHIP 100 5% 1/16W
R53 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R54 1-216-817-11 METAL CHIP 470 5% 1/16W
R56 1-216-815-11 METAL CHIP 330 5% 1/16W
R58 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
< TRANSFORMER >
T1 1-433-741-11 TRANSFORMER, IF
T2 1-419-465-11 COIL (DET)
< VIBRATOR >
X1 1-760-130-11 VIBRATOR, CRYSTAL (75kHz)
**************************************************************
MISCELLANEOUS
**************
8 1-452-899-11 MAGNET
71 1-792-684-11 WIRE (FLAT TYPE) (16 CORE)
* 72 1-757-968-11 FFC CABLE 14P
101 1-757-967-11 FFC CABLE 27P
* 111 1-757-969-11 FFC CABLE 13P
0 501 8-848-483-05 OPTICAL PICK-UP DEVICE (KSS-213C)
ANT1 1-754-191-11 ANTENNA, TELESCOPIC
HE301 1-543-876-14 HEAD (ERASE)
HRP301 1-500-668-11 HEAD, MAGNETIC (RECORD/PLAYBACK)
LCD801 1-804-401-11 DISPLAY PANEL, LIQUID CRYSTAL
M301 A-3320-446-A MOTOR ASSY (WITH PULLEY)
(CAPSTAN/REEL)
M702 X-2625-769-1 GERA ASSY (MB), MOTOR (SLED)
S303 1-762-679-11 SWITCH, LEAF (MOTOR ON/OFF)
S304 1-771-059-11 SWITCH, LEAF (TAPE PLAY)
S901 1-692-960-11 SWITCH, PUSH (1 KEY) (CD LID OPEN/CLOSE)
0 T901 1-437-320-11 TRANSFORMER, POWER
************************************************************
**************
HARDWARE LIST
**************
#1 7-685-647-14 SCREW +BVTP 3X10 TYPE2 N-S
#2 7-685-649-79 SCREW +BVTP 3X14 TYPE2 N-S
#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
#4 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S
#5 7-685-853-04 SCREW +BVTT 2X6 (S)
#6 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
#7 7-682-548-04 SCREW +B 3X8
#8 7-685-903-31 SCREW +PTPWH 3X10 (TYPE2)
#9 7-621-770-87 SCREW +B 2.6X5
#10 7-685-783-09 SCREW +PTT 2X6 (S)
************************************************************
R59 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R60 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R61 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R63 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R64 1-216-821-11 METAL CHIP 1K 5% 1/16W
R66 1-216-805-11 METAL CHIP 47 5% 1/16W
R91 1-216-821-11 METAL CHIP 1K 5% 1/16W
R92 1-216-821-11 METAL CHIP 1K 5% 1/16W
R93 1-216-821-11 METAL CHIP 1K 5% 1/16W
54
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.

CFD-E75L
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
ACCESSORIES & PACKING MATERIALS
*******************************
0 1-770-019-11 ADAPTOR, CONVERSION PULG 3P (UK)
0 1-769-412-13 CORD, POWER
3-228-965-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(AEP/UK)
3-228-965-41 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(AEP)
3-228-965-51 MANUAL, INSTRUCTION
(DUTCH, PORTUGUESE) (AEP)
3-228-965-61 MANUAL, INSTRUCTION (ITALIAN) (IT)
3-228-965-71 MANUAL, INSTRUCTION (SWEDISH, FINNISH)
(EE, CIS)
3-228-965-81 MANUAL, INSTRUCTION
(POLISH, CZECH, HUNGARIAN) (EE, CIS)
3-228-965-91 MANUAL, INSTRUCTION
(RUSSIAN, SLOVAKIAN) (EE, CIS)
A-3013-904-A REMOTE CONTROL UNIT (RMT-CE75AD/LC)
(for BLUE)
A-3013-905-A REMOTE CONTROL UNIT (RMT-CE75AD/DC)
(for ORANGE)
A-3258-093-A REMOTE CONTROL UNIT (RMT-CE75A/WC)
(for WHITE)
3-027-153-11 LID, BATTERY CASE
(for REMOTE CONTROL UNIT)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
55

CFD-E75L
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.0 2001.05 New