Connector Tecjnology, Shelf Supports - Carcase Connectors - Hafele

Connector Technology, Shelf Supports 

Carcase Connectors 

AEROFIX 100 insert 

37,3-72,3 

• Area of application: Honeycomb panels without frame, 

with 4 mm top layers 

• Dimensions: For drill hole diameter of 10 mm 

• Material: Plastic, integrated single-component PUR adhesive 

For wood thickness Thread lenght Cat. No. 

32 mm 22 mm 039.70.324 

Packing: 100 or 1,000 pcs. 

2 

14,7-49,7 

Connectors 

Shelf support 

Usage 

The advantages of the AEROFIX 100: 

Integrated adhesive 

• No additional work operation 

• No additional equipment needed 

We reserve the right to alter specifications without notice (SEA Basic 2008/09). 

Mounting plates and hinges 

Rear panel connectors 

Wardrobe rail and rail end supports 

Runners 

Sliding door fittings 

Castors 

Table legs and furniture feets 

Locking systems 

Furniture handles and decorative fittings 

Connects both top layers 

• Excellent stability 

Easy to install 

• Can be pushed in manually or by automatic machines 

Receptacle for standard screws and bolts 

• Use of standard product range 

New products and systems: www.hafele.com 

SEA 2.11



AEROFIX 100 insert 

Processing steps 

Upper top layer 

2 

Lower top layer 

1. Drill hole D=10 mm through upper top layer 

Use a drilling depth that keeps the lower top 

layer free of residual adhesive. 

2. Push AEROFIX 100 into hole. 

Fastening screw 

Push in inner 

part until lever 

with surface 

3. Push in Aerofix 100 until it is flush with the 

4. Screws and bolts can be screwed in 

surface. The AEROFIX 100 expands below the 

immediately after inserting the AEROFIX. The full 

upper top layer. The adhesive distributes itself 

load capacity of the installed fittings is reached 

between the two top layers at the same time. 

after 16 hours. 

Structure of the AEROFIX 100 Adhesive distribution of the AEROFIX 100 

Lower adhesive distribution 

Adhesive cartridge 

Inner part 

Closure cap 

Dowel housing 

Upper adhesive distribution 


SEA 2.12 

New products and systems: www.hafele.com



VARIANTA special screw for lightweight panels 

• Area of application: For lightweight panels 

• Finish: Galvanized 

For drilling hole Ø Thread lenght Cat. No. 

3 mm 14 mm 013.30.900 

5 mm 13 mm 013.30.910 


A large selection of standard fittings can be attached to top 

layers of 4 mm and above using the Varianta special screw. 

2 

Connectors 

Usage 

Shelf support 

Mounting plates and hinges 

Rear panel connectors 

Wardrobe rail and rail end supports 

Runners 

Sliding door fittings 

Castors 

Table legs and furniture feets 

Locking systems 

Furniture handles and decorative fittings 



SEA 2.13



TAB 20 HC Connector housing 

2 

For wooden thickness 32 mm 

Drilling 

depth 


Drilling 

depth 

• Area of application: For honeycomb panels with a top layer (chipboard or MDF) of 4 mm and above 

• Suitable for: Honeycomb panels without frame 

• Diameter: Boss insert 20 mm 

• For wood thickness: 32 to 60 mm 

• Drilling depth: 22 or 26.5 mm 


• Material: Support and tightening element: 

Zinc alloy, boss insert: Plastic 

• Finish: Support and tightening element: 

Nickel plated or black, boss insert: Natural 

• Drill hole Ø: Boss insert 20 mm 

Varianta special screw 3 or 5 mm 

• Drive: PZ2, PH2 or flat blade 

For wood thickn. Dim. A Drill. depth Black Nickel pl. 

32 mm 16 mm 22 mm 263.95.332 263.95.732 

Packing: 100 pc. 


• Material: Support and tightening element: 

Zinc alloy, boss insert: Plastic 

• Finish: Support and tightening element: Nickel 

plated or black, boss insert: Natural 


Varianta special screw 3 or 5 mm 

• Drive: PZ2, PH2 or flat blade 

For wood thickn. Dim. A Drill. depth Black Nickel pl. 

40 – 60 mm 20 mm 26.5 mm 263.95.335 263.95.735 



SEA 2.14 




RAFIX 20 HC Connector housing 

Drilling 

depth 

Wooden 

thickness 


2 

• Area of application: For honeycomb panels with a top layer (chipboard or MDF) of 4 mm and above 

• Suitable for: Honeycomb panels without frame 

• Diameter: Boss insert 20 mm, dowel 5 mm 

• For wood thickness: 32 to 50 mm 

• Drilling depth: 22.5 mm 


• Material: Boss insert: Plastic, tightening element: Zinc alloy 

• For wood thickness: 32 – 50 mm 


Dowel 5 mm 

• Drive: PZ2 cross slot 

Dim. A Drilling depth Colour Cat. No. 

16 mm 22.5 mm Brown 263.18.102 

White 263.18.702 

Black 263.18.302 

Nickel coloured lacquered 263.18.602 



M20 Connecting bolt for Ø 5 mm drill hole 

• Material: Zinc alloy 

• Thread: Special thread 


For wood thickness 

Galvanized 

7.5 mm 263.20.131 



SEA 2.15



MAXIFIX 35 HC for honeycomb worktop connector 

2 

The MAXIFIX 35 HC worktop connector is particularly suitable for 

strong connections in honeycomb worktops in kitchens. 

The top layer of the honeycomb worktop must be at least 8 mm thick. 

• Material: Housing cup and height adjustment facility: 

Plastic, connecting bolt, knurled nut and 

pressure plate: Steel, 

connector housing: Zinc alloy 

• Finish: Black, connector housing: Nickel plated, 

connecting bolt: Galvanized 

• Length: Connecting bolts 90 or 165 mm 

• Diameter: Housing cup: 40 mm 

• Drive: PZ2 cross slot, SW6 Allen key 

For panel thickness Lenght mm Cat. No. 

For honeycomb worktops with frame at one side 

50 mm 90 mm 262.89.121 

165 mm 262.89.122 

60 mm 90 mm 262.89.131 

165 mm 262.89.132 

For honeycomb worktops without frame 

50 mm 90 mm 262.89.021 

165 mm 262.89.022 

60 mm 90 mm 262.89.031 

165 mm 262.89.032 

Packing: 2 or 20 pcs. 

Advantages: 

• Connections secured against loosening 

• Height adjustment ±2 mm 

• Drilling pattern complies with the standards of 

kitchen manufacturers 

• Fitting components engage when fitted 

• Convenient, quick tightening by turning the 

MAXIFIX connector housing 

2 versions available 

• For honeycomb worktop connections, 

with frame at one side and height adjustment facility 

• For honeycomb worktop connections, 

without frame, with height adjustment facility 

1 Housing cup 

2 MAXIFIX 35 connector housing 

3 Connecting bolt with pre-mounted knurled nut and pressure plate 

4 Height adjustment for honeycomb worktops with frame 

5 Height adjustment for honeycomb worktops without frame 

6 Adapter for housing cup for 60 mm thick panels 

7 Adapter for height adjustment facility for 60 mm thick panels 


SEA 2.16 




MAXIFIX 35 HC for honeycomb worktops 

Honeycomb worktop with notched frame 

Honeycomb worktop without frame 

q 40 

q 40 

2 

15 

q 40 

B 

q 40 

D 

q 40 

4 

D 

R 50 

16 

D 

E 

C 

B 

D 

15 

q 40 

D 

Dim. A Dim. B Dim. C Dim. D Dim. E 

50 mm 46 +0.5 mm 42 mm 42 – 51 mm 25 -0.5 mm 

80 – 90 mm 

60 mm 56 +0.5 mm 52 mm 42 – 51 mm 30 -0.5 mm 

80 – 90 mm 

• Dimension A: Wood thickness 

• Dimension B: Drilling depth for housing cup 

• Dimension C: Routing depth for connecting bolt 

• Dimension D: Centre of drill hole for housing cup to front edge of 

honeycomb worktop 

• Dimension E: Centre of insert to top edge of honeycomb worktop 


Push housing cup into pre-drilled 

honeycomb worktop. 

Allow housing cup to engage. 

Join honeycomb worktops 

vertically together. 

Push Maxifix connector housing 

into housing cup. 

Allow connector housing to engage. 

Press honeycomb panels 

horizontally together. 

Pre-tighten MAXIFIX connector housing. 

Insert connecting bolt with 

attached height adjustment facility 

at top of honeycomb worktop 

(can be inserted from above or beneath) 

Then align the height of 

honeycomb worktops with screw driver. 

Push in height adjustment facility 

between top layers as far as it will go. 

The honeycomb worktops are 

firmly connected by turning the 

MAXIFIX connector housing. 


SEA 2.17



MINIFIX 12 and 15 Carcase Connectors 

The MINIFIX family of carcase connectors is based on the centric ball principle. 

This attachment method allows a large tightening and supporting surface to be integrated in a small connector housing 

ensuring that connections are positively secured and tight. 

The half round connecting bolt head locates centrally in the cup-shaped recess in the MINIFIX housing and is positively secured. 

2 

MINIFIX therefore has many advantages: 

• Automatic centering of the bolt means that shelves are no longer subject to lateral displacement in relation to the side panel. 

• The long tightening distance of more than 5 mm from only half a turn of the housing compensates for drilling distance tolerances 

of +1 mm to approx. - 0.5 mm without loss of tightness. 

• Tension is rapidly achieved as the housing is tightened, without having to tighten the housing to the limit (195°). 

• Secure tightening is guaranteed, even in case of repeated disassembly and re-assembly. 

• Delicate and elegant shape. 

Drilling 

distance B 

Bolt hole 

Drill-hole 

Drilling depth 

• Drill-hole Ø: 12 or 15 mm, depending on choice of connector housing 

• Drilling depth: Depending on choice of connector housing and wood thickness, 

see ordering table 

• Drilling distance B: Distance from centre of MINIFIX to front edge 24 or 34 mm, 

depending on choice of connecting bolt 

• Bolt hole Ø: Diameter 5, 7 or 8 mm depending on choice of connecting bolt 


SEA 2.18 



Information 

The MINIFIX CLOCKFACE 

The MINIFIX clockface shows the tightening distance A, which 

is separated into 3 travel segments with different functions: 

1. Closing distance: 

0° – 75° (6 to 8.30) = 3.2 mm pull 

Bolt head is pulled into centre of housing (no tightening effect yet). 

2. Tightening distance: 

75° – 165° (8.30 to 11.30) = 2 mm pull 

The connection is securely tightened. Tightening is initiated at 

120° (10 o’clock), provided that specified drilling distance 

is adhered to. Optimum security will be reached at 165° (11.30 o’clock). 

2 

3. Retightening distance: 

165° – 195° (11.30 o’clock to 12.30 o’clock) = 0.5 mm pull 

The retightening distance is only required if: 

• There are drilling distance tolerances 

• A furniture item has been disassembled and re-assembled several times 

• A furniture item has been subjected to severe loading 

Definitions 

The arrow must point exactly 

in the direction of the bolt when 

the housing is inserted 

Tools required: 

For wood thicknesses from 12 mm: 

• Cross slot screwdriver PZ2 


Cross slot screwdriver PZ2 

Flat blade, size 6x1.5 

For wood thickness of 13 and 15 mm: 

• Cross slot screwdriver PZ2 or 

• Flat blade 

For wood thickness of 16 – 29 mm: 



For plastic MINIFIX 15 connector housing: 



MINIFIX tightening keys can also be used (optional). 


SEA 2.19



MINIFIX Connector housing 

Verbindungstechnik, Boden- und TablarträgerKorpusverbinderVerbindergehäuse Minifix 12Preise · Verfügbarkeit · BestellungPlanung, Konstruktion 

• Connector housing: Ø 12, 13, 15 mm 

• For wood thickness: 12 mm 

• Dimension A: Distance from centre of bolt hole top edge of 

connector housing 

• Drilling depth: 9.5 – 12.0 +0.2 mm 

2 

• Bolt hole Ø: 7 or 8 mm depending on choice of connecting bolt 

• Drilling distance B: Distance from centre of MINIFIX to front edge 

24 or 34 mm (plastic housing Ø mm) depending on choice of connecting bolt 

A Bolt hole 

A 

B Drilling depth 

C 

B 

D 

C Dimension A 

D Wood thickness 

E 

E Drilling distance B 

Connector housing without rim, for wood thickness of 12 mm 


Dimension A 


• Drilling depth: 10.2 +0.2 mm 

• Drive: PZ2 cross slot, off-centre 

• For all connecting bolts 

Dim. A Bright Nickel coloured Nickel plated Black 

6.0 mm 262.17.014 262.17.711 262.17.710 262.17.318 


Connector housing without rim, for wood thickness of 13 or 15 mm 


Dimension A 

• Drive: PZ2 cross slot or flat blade 


For wood thickness Dimension A Drilling depth Bright Nickel coloured Black Nickel plated 

Min. 13 mm 6.5 mm 11.0 +0.2 mm 262.26.071 262.26.171 262.26.371 262.26.571 

Min. 15 mm 7.5 mm 12.0 +0.5 mm 262.26.072 262.26.172 262.26.372 262.26.572 


Connector housing without rim, for wood thickness of 16 or 19 mm 

Dimension A 


• Drive: PZ2, PZ3 cross slot, flat blade or SW4 hexagon 



Min. 16 mm 8.0 mm 12.5 +0.5 mm 262.26.073 262.26.173 262.26.373 262.26.573 

Min. 19 mm 9.5 mm 14.0 +0.5 mm 262.26.075 262.26.175 262.26.375 262.26.575 





SEA 2.20 




MINIFIX 15 Connector housing 

Connector housing without rim, for wood thickness of 23, 26 or 29 mm 

Dimension A 



• Drive: PZ2, PZ3 cross slot, flat blade or hexagon SW4 


2 


Min. 23 mm 11.5 mm 16.5 +0.5 mm 262.26.264 262.26.766 262.26.862 262.26.666 

Min. 26 mm 13.0 mm 18.5 +0.5 mm 262.26.270 262.26.770 262.26.870 262.26.670 

Min. 29 mm 14.5 mm 19.5 +0.5 mm 262.26.291 262.26.793 262.26.899 262.26.693 

Packing: 1,000 or 5,000 pcs. 

Cover cap 

• Diameter: 17 mm 

• Material: Plastic 

For wood thickness 12, 13, 15 mm 

Information 

Other colours are available on request. 

For wood thickness 16 – 29 mm 

For wood thickness Brown Grey Pine coloured Black White 

12, 13, 15 mm 262.24.162 262.24.564 262.24.064 262.24.368 262.24.760 

16 – 29 mm 262.24.153 262.24.550 262.24.055 262.24.359 262.24.751 




SEA 2.21



2 

MINIFIX STANDARD S100 Connecting bolts 

With M6 thread and bold head Ø 7 mm 

• Material: Steel 

• Thread: M6 

• Drive: PZ2 cross slot or flat blade 

Thread length L Drilling distance B Yellow 

galvanized 

7.5 mm 24 mm 262.27.592 

34 mm 262.28.599 


MINIFIX STANDARD S200 Connecting bolts 

For drilled hole Ø 5 mm and bolt head Ø 6.5 mm 

With M6 thread and bolt head Ø 6.5 mm 

• Material: Steel, plastic sleeve 



Thread length L Drilling distance B Galvanized 

8.5 mm 24 mm 262.27.689 

34 mm 262.28.689 

11 mm 24 mm 262.27.679 

34 mm 262.28.679 

Packing: 2, 000 pcs. 

• Material: Steel, plastic sleeve 




7.5 mm 24 mm 262.27.699 

34 mm 262.28.699 

Packing: 2, 000 pcs. 

MINIFIX INDUSTRY M100 Connecting bolts 

For drilled hole Ø 5 mm and bolt head Ø 6.5 mm 

For drilled hole Ø 5 mm and bolt head Ø 7 mm 

With M6 thread and bolt head Ø 7 mm 

L 




Thread length L Drilling distance B Yellow 

galvanized 

8.5 mm 24 mm 262.27.615 

34 mm 262.28.615 

Packing: 2,000 pcs. 





11 mm 24 mm 262.27.627 

34 mm 262.28.624 






7.5 mm 24 mm 262.27.645 

34 mm 262.28.642 



SEA 2.22 




Accessories for connecting bolts for drilled hole Ø 5 mm or with M6 thread 

Spreading dowels in dowel magazine, for drilled hole Ø 5 mm 

Drilling distance Material Cat. No. 

5 mm Nylon 042.98.051 


For drill hole Ø 5 mm 

2 

Dowels for M6 thread 

M6 Spreading dowel 

M6 Glue-in dowel 

For drill hole Ø 8 or 10 mm 

Drilling distance Material Length L Cat. No. 

M6 spreading dowel 

8 mm Brass 9 mm 039.00.267 

12 mm 039.00.061 

M6 glue-in dowel 

8 mm Nylon 11 mm 039.33.462 

10 mm Nylon 9 mm 039.33.364 

11 mm 039.33.266 

13 mm 039.33.060 




SEA 2.23



MINIFIX COMFORT C100 Spreading bolt 

Function 

When the connector is tightened the taper on the bolt spreads the dowel and forces the threads into the wood. 

The stronger the tightening force acts, the securer the connection. 

• Drilling depth stop ensures ideal bolt position 

• No surfaces damage caused by insertion and removal of spreading bolt 

2 

For drilled hole Ø 10 mm 

• Area of application: For one-sided installation, for industry and 

trade, for assembly-friendly flat-packed furniture 

• Material: Zinc alloy bolt, plastic spreading dowel 

• Colour: Spreading dowel black 

• Thread: Spreading dowel 

• Installation: For toolless insertion and unscrewing 


11.5 mm 24 mm 262.09.211 

34 mm 262.09.311 


MINIFIX Double bolt 

For drilled hole Ø 7 mm, with rim 

Installation 

• Area of application: For edge-to-edge joints 


Drilling distance B 

Galvanized 

34 mm 262.28.786 


For drilled hole Ø 8 mm, with snap ring 

Installation 

For double-side installation with drilled hole Ø 7 mm 

Double bolt with joint 

• Area of application: For double-sided installation 



16 mm 24 mm 262.27.805 

34 mm 262.28.802 

19 mm 24 mm 262.27.814 

34 mm 262.28.811 


• Area of application: For mitre cuts of 20º to 90º 



Galvanized 

24 mm 262.12.859 

44 mm 262.12.939 

Packing: 100 or 500 pieces 


SEA 2.24 




MAXIFIX 35 Carcase Connectors 

Drilling distance 


Wood thickness 

Dim. A 

Bolt hole 

2 

The MAXIFIX 35 carcase connector is particularly suitable for connections that are permanently subjected to high loads such as connections 

in carcases and beds, counters and face-frame furniture. Can be used for wood thicknesses of 19 mm and above. 

The MAXIFIX 35 carcase connector is particularly suitable for mass manufacture in the furniture industry. 

MAXIFIX 35 Connector housing 

PZ3 cross slot 

Dimension A 

SW6 hexagon socket 


• Dimension A: 9.5 mm 

• Drilling depth 15.5 mm 


For wood thickness Bright Nickel 

plated 

Nickel 

coloured 

PZ3 cross slot 

Min. 19 mm 262.87.013 262.87.713 262.87.613 

SW6 hexagon socket 

Min. 19 mm 262.87.003 262.87.703 262.87.603 


Trim cap for MAXIFIX 35 


White Brown Beige Black Nickel 

coloured 

262.87.790 262.87.190 262.87.490 262.87.390 262.87.690 



With M8 thread 

Screw-in dowel 

• Area of application: For MAXIFIX 35 


• Thread length L: 9.5 mm 

Thread Drilling dimensions Bolt length BL Galvanized 

M8 35 mm 28.5 mm 262.87.911 

55 mm 48.5 mm 262.87.912 

Packing: 100 pcs. 

Inside-thread For drill hole Ø Length L Yellow chromatized 

M6 8 mm 15 mm 030.10.564 

17 mm 030.10.565 

M8 10 mm 15 mm 030.10.584 

17 mm 030.10.585 

Packing: 100, 2,000, 2,500 or 3,000 pcs. 


SEA 2.25



RONDORFIX Carcase connector for wood thickness 16 mm 

Installation 

Drilling depht 


2 

Drilling depht 



Dimension A 

= depending on type of housing and wood thickness 

= B 33.5 (33.5 mm) drilling distance from centre of housing to front edge 

= 1/2 of wood thickness 

RONDORFIX Eccentric housing without flanged rim 


• Finish: Bright 

Drilling depth Dimensions A Cat. No. 

12 mm 7 mm 262.75.061 


Cover cap 

• Area of application: For RONDORFIX eccentric housing without 

flaged rim 


Colour 

Cat. No. 

White 262.78.704 


RONDORFIX Glued dowels with M6 internal thread 

• Material: Plastic, natural coloured 

• Colour: Natural coloured 

Drilled hole D Length L Cat. No. 

8 mm 11 mm 039.33.462 

10 mm 9 mm 039.33.364 



SEA 2.26 




RONDORFIX Connecting bolt 

With special thread screws into pre-drilled holes, for one-sided or two-sided mounting 


• For pre-drilled holes Ø 5 mm 

Drilling distance Finish Cat. No. 

33.5 mm Bright 262.75.277 

Galvanized 262.75.776 


With M6 thread, screws into dowels, for one-sided mounting 


• For pre-drilled holes Ø 8 or 10 mm 

Drilling distance Finish Cat. No. 

33.5 mm Bright 262.75.098 

Galvanized 262.75.990 


2 

CONFA 35 Universal connector 

Housing 

• Area of application: Fush connector, for connections that are 

extremely strong and can bear heavy loads. 


• Toleranz are compensated for by long tightening distance 

• Tightening with hexagon socket size 6 

For wood thickness Diameter Cat. No. 

24 mm 35 mm 262.69.009 


Connecting bolt M8 thread 


• Drilling distance: 55 mm 


Cat. No. 

262.69.045 



SEA 2.27



RAFIX 20 Connector housing, without pin 

With and without ridge 

For flush fitting 




2 

Drilling depth contingent on wood thickness 

and used connector housing 





• Dimension A: Distance between centre of bolt hole and top edge, corresponds to half of the wood thickness 

• Drilling depth: Depends on wood thickness and type of connector housing that used. 

• Features: With zinc alloy tightening element 




For wood thickness Dimension A Drilling depth Burnished Nickel plated 

With ridge 

16 mm 8.0 mm 12.7 +0.2 mm – 263.15.703 

19 mm 9.5 mm 14.2 +0.2 mm 263.15.105 263.15.705 

Without ridge 

16 mm 8.0 mm 12.7 +0.2 mm 263.11.103 263.11.703 

19 mm 9.5 mm 14.2 +0.2 mm 263.11.105 263.11.705 




• Drive: Cross slot PZ2 

For wood thickness Dimension A Drilling depth Beige Brown Black White White aluminium 

With ridge 

16 mm 8.0 mm 12.7 +0.2 mm 263.14.403 263.14.103 – 263.14.703 263.14.203 

19 mm 9.5 mm 14.2 +0.2 mm 263.14.405 263.14.105 – 263.14.705 263.14.205 

Without ridge 

16 mm 8.0 mm 12.7 +0.2 mm 263.10.403 263.10.103 263.10.303 263.10.703 263.10.203 

19 mm 9.5 mm 14.2 +0.2 mm 263.10.405 263.10.105 263.10.305 263.10.705 263.10.205 


For flush fitting 

For wood thickness Dimension A Drilling depth Beige Brown Black White 

16 mm 8.0 mm 12.7 +0.2 mm 263.50.403 263.50.103 – 263.50.703 

19 mm 9.5 mm 14.2 +0.2 mm 263.50.405 263.50.105 263.50.305 263.50.705 




• Features: With countersunk rim for flush fitting 

• Drive: Cross slot PZ2 


SEA 2.28 




RAFIX TAB 20 Connector 







2 

Dimension A: Distance between centre of bolt 

hole and top edge, corresponds to half of 

the wood thickness. 


Flush mounted 

Function 

• The connector housing is pressed into the shelf and pushed onto a RAFIX 7 mm diameter connecting bolt. 

• The tapered surfaces of the connector housing ensure that the connecting bolt is extremely tight. 

• The catch prevents the shelf from “moving” upwards away from the connecting bolt. 

• For shelves and support panels the drop-down shelves can be fastened using RAFIX-TAB alone. 

• RAFIX carcase connectors can also be inserted into the shelves of tall cabinets to prevent the side panels from “bulging out”. 

Standard, with ridge 



For wood thickness Dimension A Drilling depth Burnished Brown Black White 

16 mm 8 mm 12.7 mm 263.09.437 263.09.133 263.09.339 263.09.731 



Flush mounted, with ridge 


• Version: With countersunk rim for flush fitting 

• No protruding parts due to the countersunk rim in the connector 

housing 

• Shelves can be stacked without intermediate layers 

For wood thickness Dimension A Drilling depth Burnished Brown Black White 

16 mm 8 mm 12.7 mm 263.07.430 263.07.130 263.07.330 263.07.730 




SEA 2.29



RAFIX STANDARD S20 Connecting bolts 

2 


Glue-in dowel magazine, for drilled hole Ø 5 mm 



• Drive: PZ2 cross slot and flat blade 

Thread length L 

Galvanized 

11 mm 263.20.810 


Drilling distance Material Cat. No. 

5 mm Nylon 042.98.051 





• Drive: PZ2 cross slot and flat blade 


Galvanized 

11 mm 263.20.847 

15 mm 263.20.856 

Packing: 100, 1,000 or 2,000 pcs. 






5 mm Brass 8 mm 051.45.004 


8 mm Nylon 8 mm 039.33.140 

10 mm 039.33.042 

10 mm Nylon 11 mm 039.33.239 

13 mm 039.33.033 

Packing: 100, 1,000 or 5,000 pcs. 

Threaded sleeve 

Installation 

End screw 

Installation 

• Area of application: For double-sided installation 


Drilling distance Length L Galvanized 

5 mm 15 mm 267.00.911 

18 mm 267.00.912 

22 mm 267.00.913 


• Area of application: Suitable as capped bolt with sleeve 


Length L 

Nickel plated 

8 mm 020.92.711 

10 mm 020.92.720 

Packing: 100, 1,000 or 5,000 pcs. 


SEA 2.30 







M6 Dowel magazine 

For drilled hole Ø 10 

For drilled hole Ø 



8 mm Brass 9 mm 039.00.267 

12 mm 039.00.061 


8 mm Nylon 11 mm 039.33.462 

10 mm Nylon 9 mm 039.33.364 

11 mm 039.33.266 

13 mm 039.33.060 

M6 Dowel magazine 

10 mm Nylon 13 mm 039.34.067 

2 

Packing: 20, 100 or 1,000 pcs. 

RAFIX INDUSTRY M20 connecting bolts for drilled hole Ø 5 mm 





Galvanized 

7.5 mm 263.20.131 




Galvanized 

12 mm 263.20.981 

Packing: 100, 1,000 or 5,000 pcs. 

RAFIX Trim cap 

• Area of application: For covering the Ø 10 mm through hole and 

allowing access to tightening element from above 



Colour 

Cat. No. 

White 045.13.704 

Beige 045.13.400 

Brown 045.13.106 

Black 045.13.300 



SEA 2.31



CONFIRMAT One-piece connector 

Drilling dimension 

Drilling hole Ø 

2 

Blind drill hole 

Through hole for shank 

For drilling hole Ø 4 mm 


• Head hole Ø: 2.5 mm 

• Type of head: Countersunk head 


Length 

Cat. No. 

38 mm 264.37.098 

50 mm 264.37.196 

Packing: 100, 500 or 2,000 pcs. 

For drilling hole Ø 5 mm 


• Type of head: Countersunk head 

Shank Ø Length L Galvanized 

6.3 mm 50 mm 264.52.190 

7.0 mm 38 mm 264.42.091 

50 mm 264.42.190 

70 mm 264.42.291 

Packing: 100, 500, 1,000 or 1,500 pcs. 

TAB 18 with tightening element 

Screw fixing 


TAB 18 without tightening element 

Screw fixing 


• Version: With tightening element 

• Installation: Support for screwing or plugging into Ø 5 mm drilled 

hole boss insert for press fitting into Ø 18 mm drilled hole 

For wood thickness Dimension A Drilling depth Nickel plated 

16 mm 8.0 mm 13.0 mm 263.66.530 

19 mm 9.5 mm 15.0 mm 263.66.558 

23 mm 11.5 mm 17.0 mm 263.66.576 

26 mm 13.0 mm 18.5 mm 263.66.585 

29 mm 14.5 mm 20.0 mm 263.66.594 

32 mm 16.0 mm 22.0 mm 263.66.601 

50 mm 25.0 mm 31.0 mm 263.66.635 


• Installation: Support for screwing or plugging into Ø 5 mm drilled 

hole boss insert for press fitting into Ø 18 mm drilled hole 

For wood thickness Dimension A Drilling depth Nickel plated 

16 mm 8.0 mm 13.0 mm 263.73.535 

19 mm 9.5 mm 15.0 mm 263.73.553 

23 mm 11.5 mm 17.0 mm 263.73.571 

26 mm 13.0 mm 18.5 mm 263.73.580 

29 mm 14.5 mm 20.0 mm 263.73.599 

32 mm 16.0 mm 22.0 mm 263.73.606 



SEA 2.32 




MAXIFIX 35 Worktop connector 

• Material: Zinc alloy housing, steel bolt and segemental element 

• Finish: Housing bright, bolt and segmental piece galvanized 

• Version: With pre-mounted bolt and segmental element 

• For wood thickness: Min. 19 mm 

• Drive: Hexagon socket, SW 6 

• Installation: Flush mounting with quick tension 

2 


Supplied with 

1 Connector housing MAXIFIX 35 

1 Connecting bolt 

1 Segmental element 

Length L Drilling dimension B Cat. No. 

68.5 mm 32 – 41 mm 262.87.041 

164.5 mm 75 – 84 mm 262.87.042 


Worktop connector 



• Installation: Insert connector into table tops and tighten 

using allen key 

Length L Drilling dimension B Cat. No. 

65 mm 32 – 41 mm 262.96.211 

150 mm 75 – 84 mm 262.96.220 





SEA 2.33

Connector Tecjnology, Shelf Supports - Carcase Connectors - Hafele

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?