Explorer Vision - THORN Lighting

More documents

Recommendations

Info

L L L Explorer Project – up to 256 emergency luminaires Simple to operate and configure Expanding the Explorer Project to work with more than 128 emergency luminaires In this configuration, channel ‘B’ becomes a ‘signaling bus’ and is used for communication to the XPX64 extender modules. There must be no emergency luminaires directly connected to this channel in this mode. This helps with the wiring planning as there can be up to 300m of cable between the XP128 controller and the XPX64. The maximum distance from the XPX64 to the furthest luminaire is another 300m. If this still causes planning difficulties, there is a kit to extend the distances a further 300m (XP300m+) If you still need more capacity see Explorer Vision, for up to 5000 luminaires! The diagram below shows the luminaires connected in a string. This is often an easy method of installation, but you soon reach the 300m maximum for the data cables. Use a ‘star connection’ or make a branch off from the main run to achieve the cable run to your furthest luminaire within the cable limit. Optional isolators break these runs into easily managed segments (of 20 luminaires) to speed up commissioning. Explorer Project uses eDALI and DALI signalling on the bus, which means that it works with all Thorn addressable emergency luminaires and other DALI compatible emergency luminaires. ........................... Third floor Second floor First floor GSM Module Ground floor 300m max to last XP-Extender .................................................................................................................................................. ........................................ ................................... RS232 (max 3m) ........................... ........................... ........................... ................. XP128 Controller XP Extender Loop 4 64 luminaires 300m max from XP-Extender XP Extender Loop 3 64 luminaires 300m max from XP-Extender XP Extender Loop 2 64 luminaires 300m max from XP-Extender ............................. Loop 1 64 luminaires 300m max (furthest luminaire 300m away) XP Extender GSM Module XP128 Control Mains ................................................................................ Typical installation for up to 256 luminaires Isolator every 20 luminaires speeds up commissioning Can be star connected *) *) *) *) PE N L A-D1 A-D2 B-D1 B-D2 Tx Rx Gnd K11 K12 K14 K21 K22 K24 K31 K32 K34 Group 1 max. 300m/1.5mm 2 / max. 64 EM - Ballasts *) *) *) *) *) *) max. 300m/1.5mm 2 / max. 64 EM - Ballasts out D1 out D2 in D1 in D2 XP X64 max. 300m 1.5mm 2 Group 2 *) *) *) *) *) *) *) N max. 300m/1.5mm 2 / max. 64 EM - Ballasts out D1 out D2 in D1 in D2 XP X64 Group 3 *) *) *) *) *) *) *) N max. 300m/1.5mm 2 / max. 64 EM - Ballasts out D1 out D2 in D1 in D2 XP X64 Group 4 *) *) *) *) *) *) *) N
SelfTest Project Vision 1. Touch screen Used to operate the system. The screens are intuitively arranged for easy use. This first screen gives access to the quick menu or other pages to input data, display test results and so on. 2 and 3. Testing Automatic tests normally run once a week. When a manual or duration test is required, it can be selected here. The block feature is used when selected luminaires (in sensitive areas such as operating theatres) should only be tested manually. 4. Addressing Luminaires are addressed on site after installation. No special programming is required, making the process quick and reliable, with no logistical problems. 5. Assigning relays and GSM Relays can be selected to operate according to the type of test or fault. GSM operations are also configured here. Summary of benefits • Performs all of the testing and records the results • Cost effective compliance with emergency lighting testing regulations • Test results stored for 2 years • Explorer Project is for up to 256 emergency luminaires • XP300m+ gives additional wiring distance 1. 2. 3. 4. Test Funct. test Duration test Relay all groups similar Start function test every Thur, Fri at start function test now ... also see test book Luminaires Address Check Callibration Luminaire address group 1 (10 luminaires) location: Tue, 10.02.2004 16:52 Explorer Project XP128 Last test result: OK logical address: auto-search . . . < Previous 16 : 00 : 00 oclock. Quick Menu BLOCK system . . . Start function test . . . Start duration test . . . 1 Floor 1, north entry Next > Relaybuzzer Assignments Status Factory settings OK Lamp fault Battery fault Comm. problem Test error, time out Func. test running Relay 1 Relay 2 Relay 3 Buzzer assign GSM info ? info ? Cancel Ass ? ? 5.
Page 1 and 2: Explorer Comprehensive testing for
Page 3 and 4: Emergency lighting testing - Integr
Page 5 and 6: 9 10 8 11 7 12 6 1 5 2 4 3 Explorer
Page 7: 24V L Gnd N Gnd TxD RxD 24V Gnd Exp
Page 11 and 12: For the more challenging applicatio
Page 13 and 14: Typical luminaires available as Exp
Page 15 and 16: Explorer Vision Components SelfTest

Explorer Vision - THORN Lighting

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?