Rocket Aluminum Bike Trailer and Stroller manual.pdf - Instep.net

More documents

Recommendations

Info

STEP 8 Prepare wheels for attachment 8A 8B 8C Axle Quick-release lever Wheel brackets Quick-release axle nut 8A. Lift the front end of the trailer up and rest the trailer on its back. The wheel bracket slots open upward. 8B. The wheel axles may come with black protective caps. These are for shipping and should be discarded. 8C. Open the quick-release lever and loosen the nut a few turns so the axle is visible and there is a space between the quick-release axle nut and the black spacer nuts. Do not remove the quick-release nut. STEP9 Insert wheels into wheel brackets 9A 9B 9C Black spacer nuts 9A. Slide the wheel all the way down into the wheel bracket slots with the quick-release lever to the outside. The axle should rest at the bottom of the bracket slots to ensure that the wheel is properly aligned. 9B. Tighten the nut by hand and then clamp the lever down so that the wheel is secured. 9C. Repeat for the other wheel. Check to make sure that both wheels are secure and aligned. STEP 10 Release tow bar and rotate into it position for use in trailer and stroller modes 10A 10B 10C 10D Coupler Tow bar 10A. The tow bar rests within a slotted bracket and is held in place by a spring-loaded latch. 10B. Grip the tow bar with your left hand and push both sides of the latch downward with your right hand. Once the latch clears the slot, remove your right hand WARNING To prevent injury, please use extreme care when folding and unfolding this product! 10C. Rotate the tow bar upward. Be mindful of the coupler at the end of the tow bar. 10D. Rotate the tow bar all the way up and press it into the bracket. The latch will engage automatically. 6
STEP 11 Prepare front wheel assembly for attachment 11A 11B 11C Carriage bolt Bracket Fork Lock knob 11A. Carefully set the trailer back down with the towbar extended in front and the wheels mounted in place. 11B. Locate the front wheel assembly: wheel, fork, bracket, lock knob, washers, and carriage bolt. 11C. Unscrew the lock knob and remove it completely from the carriage bolt. Then, remove the washers from the carriage bolt. Leave the carriage bolt within the bracket. STEP 12 Position front wheel assembly to tow bar 12A Hole in 12B 12C towbar 12A. Hold the end of the tow bar with your left hand and the front wheel bracket in your right hand. 12B. Hold your thumb over the head of the carriage bolt and slide the end of the carriage bolt completely through the hole in the tow bar so that that the bracket rests snugly against the tow bar. 12C. Place the washers over the end of the carriage bolt and tighten the lock knob completely. STEP 13 13A Handlebar 13B 13C 13D clamp 13A. Loosen the lock knobs on the handlebar clamps but do not remove the lock knobs. Hold the handlebar so that the clamps are positioned at the rear of the cabin frame. 13B. Pinch the clamp to open it and slide the clamp over the canopy and cabin frame tubing. 13C. Tighten the lock knob and repeat for the other side. 13D. The product is now ready for use in stroller mode. WARNING Always use the safety wrist strap when pushing this product in stroller mode! 7
Page 1 and 2: Rocket Bike Trailer and Stroller Ow
Page 3 and 4: ASSEMBLY AND OPERATING INSTRUCTIONS
Page 5: STEP 5 Begin attachment of the cano
Page 9 and 10: STEP 17 Coupler attachment for bike
Page 11 and 12: Removal of the trailer from the bik

Rocket Aluminum Bike Trailer and Stroller manual.pdf - Instep.net

Create successful ePaper yourself

Delete template?

Save as template?