om, speedztr 30 ca, 2010-01, zero turn: consumer, 966504101 - Dixon

More documents

Recommendations

Info

Caster Wheels Check every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for service. Foam filled tires or solid tires will void the warranty. Removal and installation of caster wheel 1. Remove nut (1) and caster bolt (2). 2. Pull the wheel out of the fork and take care of the sleeve (3). 3. Reinstall in reverse order. Tighten caster bolt. MAINTENANCE 1 2 IMPORTANT INFORMATION DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures. Only use O.E.M. specified tires. Caster wheels 3 8050-001 Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the debris sticks. Use compressed air to clean the top side of mower deck. For cleaning the underside of the deck, use the cleanout port. Attach the quick connect (from the accessory packet) to any garden hose. After mowing, snap the hose to the cleanout port and turn on water. Restart the mower and engage the blades to use the spinning action to wash away debris. Make sure the hose is away from the mower blades. Avoid spraying water on the engine and electrical components. Clean regularly 8058-084 Use protective glasses when cleaning and washing. Hardware Check daily. Inspect the entire machine for loose or missing hardware. 40
LUBRICATION 8050-924 12/12 Every year 1/52 Every Week 1/365 Every day Lubricate with grease gun Oil change Filter change Lubricate with oil can Level check General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease. For daily use, the machine should be lubricated twice weekly. Wipe away excess grease after lubrication. It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts. 41
Page 1 and 2: Operator Manual SPDZTR 30 CA / 9665
Page 3 and 4: Contents INTRODUCTION..............
Page 5 and 6: INTRODUCTION Congratulations Thank
Page 7 and 8: symbols and decals These symbols ar
Page 9 and 10: SAFETY Safety Instructions These in
Page 11 and 12: SAFETY Personal Safety Equipment WA
Page 13 and 14: SAFETY WARNING! The engine must not
Page 15 and 16: SAFETY Sparking can occur when work
Page 17 and 18: CONTROLS This operator’s manual d
Page 19 and 20: CONTROLS Parking Brake The parking
Page 21 and 22: Fuel Shut Off Valve The fuel shut o
Page 23 and 24: operation Read the Safety section a
Page 25 and 26: Move the steering controls outward
Page 27 and 28: Slowly push the choke control down
Page 29 and 30: Operating on Hills Read the Safety
Page 31 and 32: Stopping the Engine Allow the engin
Page 33 and 34: MAINTENANCE Maintenance Schedule Th
Page 35 and 36: MAINTENANCE Battery Your mower is e
Page 37 and 38: Parking Brake Visually check that n
Page 39: MAINTENANCE Adjusting the Mower Dec
Page 43 and 44: TROUBLESHOOTING Problem The engine
Page 45 and 46: storage Winter Storage At the end o
Page 47 and 48: TECHNICAL DATA Torque Specification
Page 49 and 50: TECHNICAL DATA SpeedZTR 30 CA Equip
Page 51 and 52: SERVICE JOURNAL Action Date, mtr re
Page 53 and 54: SERVICE JOURNAL Action Date, mtr re
Page 56: P/N 115 312327R1 01/21/10

om, speedztr 30 ca, 2010-01, zero turn: consumer, 966504101 - Dixon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?