Produktinfo E allgemein 700 & 900 - KS Paul GmbH
Produktinfo E allgemein 700 & 900 - KS Paul GmbH
Produktinfo E allgemein 700 & 900 - KS Paul GmbH
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
PRODUCT - INFORMATION<br />
MOLY-PAUL <strong>700</strong> & <strong>900</strong> SERIES<br />
Sealing, Lubrication and Release of Refractory Products<br />
The MOLY-PAUL® <strong>900</strong> and <strong>700</strong> Product Series are fume-free and non toxic product ranges that<br />
are specially made for the "FLOW CONTROL" area of steel making. Their prime functions are to reduce<br />
the wear and extend the life of refractory parts. These high performance products are based<br />
upon naturally occurring minerals, synthetic and natural graphites, vegetable oils and water. Special<br />
additives are used as passive or active anti-oxidants. All of the products are harmless to the environment.<br />
MOLY-PAUL® <strong>900</strong> and 919 are pastes that can be applied by spatula, brush, roller or sponge.<br />
They can be used to finish both new and refurbished refractory plate surfaces.<br />
MOLY-PAUL® 942 FAV is a low-shrinking product that fills surface imperfections.<br />
MOLY-PAUL® 912 is a low friction emulsion that is applied in steel works. It is used on rotary sliding<br />
gate valve plates and the plates of linear furnace tap-hole gates to reduce wear and control friction.<br />
By design, MOLY-PAUL® 930 and 950 are available for use with atomising spray equipment such<br />
as hand-held spray guns and purpose built automatic systems. The products can be used on all<br />
types of refractory materials and in all working conditions.<br />
The General Information (page 4) identifies the products that contain anti-oxidants.<br />
The coatings are continuous bonded dry thin films that are smooth and give an oxidation and wear<br />
resistant surface. When dry they are primarily low friction neutral refractory materials.<br />
MOLY-PAUL® 715 is for the coating of continuous casting moulds. It is suitable for both "startercasting"<br />
and "link-casting" procedures. In the concentrated form is a pseudo-plastic suspension that<br />
on drying effectively prevents molten steel from adhering to the mould faces during initial casting<br />
procedures. The product is applied with a paint sponge or roller. The spray applied aqueous suspension<br />
MOLY-PAUL® 750 is specifically formulated for use on thin slab caster moulds.<br />
MOLY-PAUL® 783 is a highly specialised non-melt grease paste with a natural oil base fluid that<br />
forms a bonded dry high purity graphite film on exposure to heat in the caster mould.<br />
MOLY-PAUL® 959 and MOLY-PAUL®979 are mould release products for monolithic refractory<br />
formers and moulds. MOLY-PAUL® 979 is used for the release of heat cured dry-mix resin bonded<br />
materials. Both products are compatible with wooden, laminate, plastic, metal and composite mould<br />
formers. They can be used in conjunction with all commonly used refractory materials, bonding<br />
agents and fillers. Application is by atomising spray gun, paint brush, paint roller or a painting pad<br />
or sponge.<br />
FUCHS LUBRITECH GMBH Neuenhofstraße 101<br />
- MOLY-PAUL DIVISION - 47055 Duisburg / Germany<br />
phone: +49 (0) 203 578861-0<br />
fax: +49 (0) 203 57886120<br />
e-mail: molypaul@fuchs-lubritech.de<br />
www.kspaul.de<br />
January 2013 Rev. 08 DIN ISO <strong>900</strong>1 / EN 2<strong>900</strong>1
PRODUCT - INFORMATION<br />
MOLY-PAUL ® 994<br />
The primary application area is its use as a release agent for assembly mortars placed between refractory<br />
ladle and tundish components. Typical locations are between the slide gate well block to<br />
inner nozzle, joints between plates and nozzles and changeable nozzles. It is also recommended for<br />
ladle gas purging well block and cone assemblies and the joints between<br />
tundish well blocks and submerged nozzles.<br />
The material hinders the sintering / bonding of ceramic refractory masses to mortars and cements<br />
that are used in conjunction with renewable refractory parts. The removal of all parts is made easier,<br />
quicker, more efficient and with minimum waste. The life of steel plant ladle linings is enhanced<br />
through reduced collateral damage.<br />
MOLY-PAUL ® 994 is also used by steel workers in the ladle "make-up" areas to enhance process<br />
capability and increase refractory life through reduced friction and wear of the refractory plate sliding<br />
surfaces. This product is designed for atomised spray application onto hot surfaces. It is applied<br />
through the collector nozzle/plate bore, or to exposed refractory plate surfaces located in "open"<br />
slide gate valve mechanisms. Both application methods introduce a non-stick neutral refractory<br />
coating to the working I sliding refractory surfaces and offset the problems caused by carbon losses<br />
from the buIk refractory.<br />
MOLY-PAUL ® 994 is a release agent for joint connections and ensures the rapid and trouble-free<br />
replacement of all ceramic parts. It does not accumulate through successive applications to form an<br />
open joint between the ceramic parts and can be applied with a simple hand held, compressed<br />
Air atomizing spray gun.<br />
FUCHS LUBRITECH GMBH Neuenhofstraße 101<br />
- MOLY-PAUL DIVISION - 47055 Duisburg / Germany<br />
phone: +49 (0) 203 578861-0<br />
fax: +49 (0) 203 57886120<br />
e-mail: molypaul@fuchs-lubritech.de<br />
www.kspaul.de<br />
January 2013 Rev. 08 DIN ISO <strong>900</strong>1 / EN 2<strong>900</strong>1
Change language