PDF Catalog - Numatics

Table of
Contents
Power Clamps .................................................................2-95
Pnuematic
UNP Series Pneumatic Power Clamp ..................................................................2-13
UBP Series Pneumatic Power Clamp .................................................................14-30
UGP Series Pneumatic Gripper. .....................................................................31-35
LSP Series Pneumatic Pin Clamp ....................................................................36-38
LTP Series Pneumatic Pin Clamp ....................................................................39-41
UAGP Series Pneumatic Power Pivot. ................................................................42-49
LAGP Series Pneumatic Power Pivot .................................................................50-57
Electronic Sensors & Wishbone Arms .................................................................. 58
Electric
LNE Series Electric Power Clamp. ...................................................................59-70
LAE Series Electric Power Clamp ....................................................................71-74
LGE Series Electric Gripper. ........................................................................75-79
LSE Series Electric Pin Clamp. ......................................................................80-84
LTE Series Electric Pin Clamp .......................................................................85-87
LAGE Series Electric Power Pivot. ...................................................................88-94
Electric Clamp Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
©Numatics 2007
Rev. 07/07
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
1

UNP Series Pneumatic Power Clamp
Features
• Conforms to NAAMS Standards
• Blade and foot mounting
• Fully adjustable opening angle
• Opening angle can be set with or without air
pressure
• Unique linkage design ensures positional
repeatability
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when air
pressure is removed
• Pneumatic ports on both sides of the cylinder
• Manual release button to open mechanism when air
pressure is removed
• Unique “programmable” all metal sensor with M12
swivel connector
How to Order
General Specifications
Weight:
UNP50: 3.2 Kg (7.1 lbs)
UNP63: 3.6 Kg (7.9 lbs)
UNP80: 11.5 Kg (25.4 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles:
UNP40: Fully adjustable from 0˚ to 125˚
UNP50, 63, 80: Fully adjustable from 0˚ to 135˚
Holding Capacity:
UNP50: 1250 Nm (11063 in-lbs)
UNP63: 1750 Nm (15488 in-lbs)
UNP80: 4000 Nm (35402 in-lbs)
UN P 63 N N U N
Series
UN = UNIVERSAL power clamps
conforming to NAAMS Standard
fully adjustable opening angle
Version
P = Pneumatic standard
Size
50 = 50 mm
63 = 63 mm
80 = 80 mm
Port Type
N = 1/4" NPT
G = G 1/4"
Sensing Style
N = No sensor
U = Electronic 24 VDC sensor with M12
swivel connector
Output Shaft
N = Dual shaft
L = Left side only
R = Right side only
Clamping Arm
N = No arm
2 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Maximum Applicable Load
UNP Series Pneumatic Power Clamp
English
operating pressure : 60 PSI
Metric
operating pressure : 4 bar
34
16
32
30
UNP80
UNP63
UNP50
15
14
UNP80
UNP63
UNP50
28
26
24
*Note: Total weight and center
of gravity calculations must
include the weight of the arm.
13
12
*Note: Total weight and center
of gravity calculations must
include the weight of the arm.
11
22
Load capacity (lb)
20
18
16
14
Load capacity (Kg)
10
9
8
7
12
6
10
5
8
4
6
3
4
2
2
1
0
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Distance from pivot point to load C.G. ( in )
0
100 150 200 250 300 350 400 450
Distance from pivot point to load C.G. ( mm )
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
3

Maximum Clamping Torque
UNP Series Pneumatic Power Clamp
English
operating pressure : 60 PSI
Metric
operating pressure : 4 bar
9000
2050
8500
8000
size 80
size 63
size 50
2000
1050
1000
size 80
size 63
size 50
7500
950
7000
900
6500
850
Clamping Torque (in-lb)
6000
5500
5000
4500
4000
Clamping Torque [Nm]
800
750
700
650
600
550
500
3500
450
3000
400
2500
350
300
2000
250
1500
200
1000
150
100
500
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [˚]
Maximum Output Torque
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [°]
English
Metric
17000
1700
16000
15000
14000
size 80
size 63
size 50
1600
1500
1400
13000
1300
Output torque (in-lb)
12000
11000
10000
9000
8000
7000
Output torque (Nm)
1200
1100
1000
900
800
700
size 80
size 63
size 50
6000
600
5000
500
4000
400
3000
300
2000
200
1000
100
0
0
58 73 87 102
4 5 6 7
Line pressure ( psi )
Line pressure ( bar )
4 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UNP50N_U Pneumatic Power Clamp
UNP Series Pneumatic Power Clamp
1/4" NPT or
Right Shaft
Left Shaft
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
5

UNP63N_U Pneumatic Power Clamp
UNP Series Pneumatic Power Clamp
1/4" NPT or
Right Shaft
Left Shaft
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
6 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UNP80N_U Pneumatic Power Clamp
UNP Series Pneumatic Power Clamp
1/4" NPT or
Right Shaft
Left Shaft
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
7

UNP50 - NAAMS Arm - Straight
UNP Series Pneumatic Power Clamp
OAL REF
‘A’
15.00
19.0 SQ.
15.00
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP.
SCR HOLES
20.03
19.97
10.000 DWL
10.00 SCR
M6 x 1.0 THRU
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N206M ACA206M 90.0 80.00 65.00 50.00 110.0 0.4 (0.9)
N207M ACA207M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.5 (1.1)
N208M ACA208M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.6 (1.3)
UNP50 - NAAMS Arm - 25mm Offset
OAL REF
‘A’
50.00
19.0 SQ.
25.00
34.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP.
SCR HOLES
20.03
19.97
10.000 DWL
10.00 SCR
M6 x 1.0 THRU
20MM DP
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N216M ACA216M 90.0 80.00 65.00 50.00 110.0 0.5 (1.1)
N217M ACA217M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.6 (1.3)
N218M ACA218M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.7 (1.5)
8 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UNP Series Pneumatic Power Clamp
UNP50 - NAAMS Arm - 50mm Offset
OAL REF
‘A’
75.00
50.00
19.0 SQ.
34.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
10.000 DWL
10.00 SCR
Ø11.0 TYP.
SCR HOLES
20.03
19.97
M6 x 1.0 THRU
20MM DP
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N226M ACA226M 90.0 80.00 65.00 50.00 110.0 0.6 (1.3)
N227M ACA227M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.7 (1.5)
N228M ACA228M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.8 (1.7)
UNP63 - NAAMS Arm - Straight
22 SQ.
OAL REF
‘A’
18.0
15.0
‘J’
‘K’
‘I’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25THRU
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.50 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N007M ACA007M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.2 (2.6)
N008M ACA008M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.4 (3.0)
N009M ACA009M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.6 (3.5)
N010M ACA010M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.9 (4.2)
N011M ACA011M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.1 (4.6)
N012M ACA012M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.3 (5.0)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
9

UNP63 - NAAMS Arm - 25mm Offset
UNP Series Pneumatic Power Clamp
55.0
25.0
50.0
‘K’
‘J’
‘I’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.50 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
OAL REF
‘A’
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N019M ACA019M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.1 (2.4)
N020M ACA020M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.3 (2.8)
N021M ACA021M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.4 (3.0)
N022M ACA022M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.5 (3.3)
N023M ACA023M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 1.6 (3.5)
N024M ACA024M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 1.9 (4.2)
UNP63 - NAAMS Arm - 70mm Offset
70.0
100.0
22 SQ.
50.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
‘K’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.500 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N031M ACA031M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.5 (3.3)
N032M ACA032M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.7 (3.7)
N033M ACA033M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.7 (3.7)
N034M ACA034M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.9 (4.2)
N035M ACA035M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.0 (4.4)
N036M ACA036M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.2 (4.8)
10 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UNP Series Pneumatic Power Clamp
UNP63 - NAAMS Arm - 120mm Offset
OAL REF
‘A’
120.0
150.0
22 SQ.
50.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
‘K’
Ø11.0 TYP
SCR HOLES
25.03
24.97
m8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.500 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N043M ACA043M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.9 (4.2)
N044M ACA044M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 2.0 (4.4)
N045M ACA045M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 2.1 (4.6)
N046M ACA046M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 2.2 (4.8)
N047M ACA047M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.4 (5.3)
N048M ACA048M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.6 (5.7)
UNP80 - NAAMS Arm - Straight
30 SQ.
OAL REF
‘A’
24.0
70.0
20.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
M10 x 1.5 THRU Ø8 (F7) TYP. DOWEL HOLES 16.000 DWL
16.00 SCR
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N110M ACA110M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 1.9 (4.2)
N111M ACA111M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.2 (4.8)
N112M ACA112M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.5 (5.5)
N113M ACA113M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 2.8 (6.2)
N114M ACA114M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.1 (6.8)
N115M ACA115M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.4 (7.5)
N116M ACA116M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.8 (8.4)
N117M ACA117M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.1 (9.0)
N118M ACA118M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.4 (9.7)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
11

UNP Series Pneumatic Power Clamp
UNP80 - NAAMS Arm - 25mm Offset
OAL REF
‘A’
30 SQ.
60.0
25.0
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N130M ACA130M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.1 (4.6)
N131M ACA131M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.3 (5.0)
N132M ACA132M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.6 (5.7)
N133M ACA133M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 2.8 (6.2)
N134M ACA134M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.1 (6.8)
N135M ACA135M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.3 (7.3)
N136M ACA136M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.6 (7.9)
N137M ACA137M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 3.8 (8.4)
N138M ACA138M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.1 (9.0)
UNP80 - NAAMS Arm - 70mm Offset
OAL REF
‘A’
30 SQ.
70.0
105.0
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5 THRU
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
12 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N150M ACA150M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.4 (5.3)
N151M ACA151M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.6 (5.7)
N152M ACA152M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.9 (6.4)
N153M ACA153M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 3.1 (6.8)
N154M ACA154M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.4 (7.5)
N155M ACA155M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.6 (7.9)
N156M ACA156M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.9 (8.6)
N157M ACA157M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.1 (9.0)
N158M ACA158M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.4 (9.7)

UNP Series Pneumatic Power Clamp
UNP80 - NAAMS Arm - 120mm Offset
OAL REF
‘A’
120.0
155.0
30 SQ.
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5 THRU
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N170M ACA170M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.8 (6.2)
N171M ACA171M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 3.0 (6.6)
N172M ACA172M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 3.3 (7.3)
N173M ACA173M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 3.5 (7.7)
N174M ACA174M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.8 (8.4)
N175M ACA175M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 4.0 (8.8)
N176M ACA176M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 4.3 (9.5)
N177M ACA177M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.5 (9.9)
N178M ACA178M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.8 (10.6)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
13

UBP Series Pneumatic Power Clamp
Features
• Blade and foot mounting
• Fully adjustable opening angle
• Opening angle can be set with or without air
pressure
• Unique linkage design ensures positional
repeatability
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when air
pressure is removed
• Pneumatic ports on both sides of the cylinder
• Manual release button to open mechanism when air
pressure is removed
• Unique “programmable” all metal sensor with M12
swivel connector
How to Order
General Specifications
Weight:
UBP40: 1.7 Kg (3.7 lbs)
UBP50: 3.2 Kg (7.1 lbs)
UBP63: 3.6 Kg (7.9 lbs)
UBP80: 11.5 Kg (25.4 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles:
UBP40: Fully adjustable from 0˚ to 125˚
UBP50, 63, 80: Fully adjustable from 0˚ to 135˚
Holding Capacity:
UBP40: 600 Nm (5310 in-lbs)
UBP50: 1250 Nm (11063 in-lbs)
UBP63: 1750 Nm (15488 in-lbs)
UBP80: 4000 Nm (35402 in-lbs)
UB
P
63
V C
U
Series
UB = UNIVERSAL power clamps
fully adjustable opening angle
Version
P = Pneumatic standard
M = Pneumatic with manual lever*
Size
40 = 40 mm
50 = 50 mm
63 = 63 mm
80 = 80 mm
*Not available on 80mm Bore
Sensing Style
N = No sensor (with protection plate)
U = Electronic 24 VDC sensor with M12
swivel connector
Arm Style
C = Central - standard
D = Right - standard
S = Left - standard
O = Central with self-holding system
P = Right with self-holding system
Q = Left with self-holding system
N = No arm
Arm Mount Position
V = 90˚
O = 180˚
N = No arm
14 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Maximum Applicable Load
UBP Series Pneumatic Power Clamp
English
operating pressure : 70 PSI
Metric
operating pressure : 5 bar
40
38
UBP80
UBP63
19
18
UBP80
UBP63
34
UBP50
UBP40
17
UBP50
UBP40
32
16
30
15
28
14
26
13
Load capacity (lb)
24
22
20
18
16
Load capacity (Kg)
12
11
10
9
8
14
7
12
6
10
5
8
4
6
3
4
2
2
1
0
0
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
100 150 200 250 300 350 400 450
Distance from pivot point to load C.G. ( in )
Distance from pivot point to load C.G. ( mm )
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
15

Maximum Clamping Torque
10500
10000
9500
9000
8500
English
operating pressure : 70 PSI
UBP Series Pneumatic Power Clamp
size 80
size 63
size 50
size 40
1150
1100
1050
1000
950
Metric
operating pressure : 5 bar
size 80
size 63
size 50
size 40
Clamping Torque (in-lb)
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
Clamping Torque [Nm]
900
850
800
750
700
650
600
550
500
450
400
350
300
250
2000
200
1500
150
1000
100
500
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [˚]
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [°]
Maximum Output Torque
English
Metric
17000
1700
16000
15000
size 80
size 63
1600
1500
14000
size 50
1400
13000
size 40
1300
Output torque (in-lb)
12000
11000
10000
9000
8000
7000
Output torque (Nm)
1200
1100
1000
900
800
700
size 80
size 63
size 50
size 40
6000
600
5000
500
4000
400
3000
300
2000
200
1000
100
0
58 73 87 102
Line pressure ( psi )
0
4 5 6 7
Line pressure ( bar )
16 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP40V_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
17

UBP40O_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
18 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP Series Pneumatic Power Clamp
UBM40V_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
19

UBP Series Pneumatic Power Clamp
UBM40O_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
20 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP50V_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
21

UBP50O_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
22 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP Series Pneumatic Power Clamp
UBM50V_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
23

UBP Series Pneumatic Power Clamp
UBM50O_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
24 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP63V_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
25

UBP63O_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
26 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP Series Pneumatic Power Clamp
UBM63V_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
27

UBP Series Pneumatic Power Clamp
UBM63O_U Pneumatic Power Clamp with Manual Lever
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
**** : DIMENSIONS TO BE RESPECTED IN CASE OTHER MANUAL LEVERS ARE USED
28 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UBP80V_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
29

UBP80O_U Pneumatic Power Clamp
UBP Series Pneumatic Power Clamp
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : TOLERANCE AT 80mm FROM PIVOT POINT
*** : AREA TO ACCESS ANGLE ADJUSTMENT
30 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UGP Series Pneumatic Gripper
Features
• Single and Double Moving Jaws
• Single and Double Tips
• Fully Adjustable opening angle
• Opening angle can be set with or without air
pressure
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when air
pressure is removed
• Pneumatic ports on both sides of the cylinder
• Manual release button to open mechanism when air
pressure is removed
• Unique “programmable” all metal sensor with M12
swivel connector
General Specifications
Weight:
UGP40: 1.8 Kg (4.0 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles:
UGP40VB: Adjustable from 0˚ to 77˚
UGP40VF: Adjustable from 0˚ to 77˚
UGP40VL: Adjustable from 0˚ to 95˚
UGP40OL: Adjustable from 0˚ to 53˚
See dimensional drawings for more information
Holding Capacity: 600Nm (5310 in-lbs)
Maximum Grip Force
How to Order
Model Number 4 Bar (58 PSI) 5 Bar (72 PSI)
UGP40V 1900 N (427 lbs) 2333 N (524 lbs)
UGP40O 1500 N (337 lbs) 1866 N (419 lbs)
UG
P
40
V L
U
Series
UG = UNIVERSAL gripper units with
fully adjustable opening angle
Version
P = Pneumatic standard
Size
40 = ø 40 mm
Sensing Style
N = No sensor (with protection plate)
U = Electronic 24 VDC sensor with M12
swivel connector
Arm Style
B = Upper and lower jaws opening;
double tips - available only with
“V” jaw mounting position
F = Upper and lower jaws opening;
single tips - available only with
“V” jaw mounting position
L = Fixed lower, upper jaws opening;
double tips
Jaw Mounting Position
V = 90˚
O = 180˚
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
31

UGP40VBU Pneumatic Gripper
UGP Series Pneumatic Gripper
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
32 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UGP40VFU Pneumatic Gripper
UGP Series Pneumatic Gripper
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
33

UGP40VLU Pneumatic Gripper
UGP Series Pneumatic Gripper
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
34 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UGP40OLU Pneumatic Gripper
UGP Series Pneumatic Gripper
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : AREA TO ACCESS ANGLE ADJUSTMENT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
35

LSP Series Pneumatic Pin Clamp
Features
• Designed to both locate and clamp material
• Multiple pin sizes available
• Different working heights available
• Unique system prevents weld slag from entering unit
• Hardened pins, hooks and scrapers for extended life
• Orthogonal version for applications with very
demanding dimensional limitations
• Remains locked in closed position even when air
pressure is removed
• Pneumatic ports on both sides of the cylinder
• Unique “programmable” all metal sensor with M12
swivel connector
How to Order
General Specifications
Weight:
LSP50G: 3.2 Kg (7.1 lbs)
LSP50U: 2.2 Kg (4.9 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP54
Maximum Clamping Force
Model Number 4 Bar (58 PSI) 5 Bar (72 PSI)
LSP50G 2850 N (640 lbs) 3500 (786 lbs)
LSP50U 3250 N (730 lbs) 4000 N (899 lbs)
LS P 50 G U 3 1 0 000
Series
LS = Pneumatic pin clamp
Version
P = Pneumatic standard
Size
50 = ø 50 mm
Model
G = Inline
U = Orthogonal
Progressive Numbering
Progressive numbers for special products
are assigned by the Sales Dept.
Working height
0 = Standard
Others upon request
Locating Pin
0 = Locating pin not included
1 = Locating pin included
Pin Diameter
2 = ø 20 mm
3 = ø 25 mm
4 = ø 30 mm
5 = ø 35 mm
6 = ø 40 mm*
Sensing Style
U = Electronic 24 VDC sensor with
M12 swivel connector
*Not available on orthogonal version
36 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LSP50GU_10 Pneumatic Pin Clamp
LSP Series Pneumatic Pin Clamp
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
37

LSP50UU_10 Pneumatic Pin Clamp
LSP Series Pneumatic Pin Clamp
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
THE SENSOR CAN BE MOUNTED ON EITHER RIGHT OR LEFT SIDE
38 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LTP Series Pneumatic Pin Clamp
Features
• Vanishing hooks provides low profile
• Multiple pin sizes available
• Unique system prevents weld slag from entering unit
• Long travel of hook designed for increased
engagement of sheet metal in oval slots
• Hardened pins, hooks and scrapers for extended life
• Remains locked in closed position even when air
pressure is removed
• Pneumatic ports on both sides of the cylinder
• Unique “programmable” all metal sensor with M12
swivel connector
General Specifications
Weight:
LTP50T: 3.2 Kg (7.1 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP54
Maximum Clamping Force
Model Number 4 Bar (58 PSI) 5 Bar (72.5 PSI)
LTP50T 2850 N (640 lbs) 3500 (786 lbs)
How to Order
LT P 50 T U 2 0 0 000
Series
LT = Pin clamp with vanishing hook
Version
P = Pneumatic
Size
50 = ø 50 mm
Model
T = With vanishing hook
Progressive Numbering
Progressive numbers for special products
are assigned by the Sales Dept.
Working height
0 = Standard
Locating Pin
0 = Locating pin non included
1 = Locating pin included
Pin Diameter
2 = ø 20 mm
3 = ø 25 mm
4 = ø 30 mm
5 = ø 35 mm
6 = ø 40 mm
Sensing Style
N = No sensor (with protection plate)
U = Electronic 24 VDC sensor
with M12 swivel connector
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
39

LTP Series Pneumatic Pin Clamp
LTP50TU_OO Pneumatic Pin Clamp with Vanishing Hook
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
40 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LTP Series Pneumatic Pin Clamp
LTP50TU_10 Pneumatic Pin Clamp with Vanishing Hook
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
41

UAGP Series Pneumatic Power Pivot
Features
• Available in three different sizes
• Manually adjustable opening angle in 15º increments
• Integrated shock absorbers
• Integrated stopping brake
• Saddle is chrome-plated steel that has a precision
ground surface and is case hardened
• Linear motion guided by roller bearings and
hardened steel guide
• Rotary motion guided by conical roller bearings
• External pre-stop assures accuracy and repeatability
of saddle
• Remains locked in closed position even when air
pressure is removed
• Unique "programmable" all metal sensor with M12
swivel connector
General Specifications
Weight:
UAGP170: 23 Kg (50.7 lbs)
UAGP300: 35 Kg (77.2 lbs)
UAGP600: 52 Kg (114.6 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Note: Brake requires minimum pressure of 4.5 Bar (65 PSI)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles:
UAGP170, 300: 15˚, 30º, 45º, 60º, 75º, 90º, 105º, 120º
UAGP600: 30º, 45º, 60º, 75º, 90º, 105º, 120º
Holding Capacity
UAGP170: 4000 Nm (2950 ft-lbs)
UAGP300: 6000 Nm (4425 ft-lbs)
UAGP600: 8000 Nm (5900 ft-lbs)
How to Order
UAG P 300 V U D B
Series
UAGP = Universal Power Pivot
with adjustable pivot rotation
in 15º intervals
Version
P = Pneumatic
Size
170
300
600
Table Position
V = Vertical 180º
O = Horizontal 90º
Brake System
B = With safety brake
Shock Absorbers Mount Position
D = Right
S = Left
Sensing Style
U = Electronic 24 VDC sensor with M12 swivel connector
42 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Maximum Applicable Load
1200
1150
1100
1050
1000
900
UAGP Series Pneumatic Power Pivot
English
operating pressure : 60 PSI
UAGP600
UAGP300
UAGP170
Load Capacity (lb)
850
800
750
700
650
600
550
500
450
400
350
300
250
200
150
100
50
0
4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
Distance from pivot point to load C.G. ( in )
500
475
450
425
400
375
Metric
operating pressure : 4 bar
UAGP600
UAGP300
UAGP170
Load Capacity (kg)
350
325
300
275
250
225
200
175
150
125
100
75
50
25
0
100 200 300 400 500 600 700 800 900 1000
Distance from pivot point to load C.G. ( mm )
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
43

UAGP170VU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
44 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UAGP170OU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
45

UAGP300VU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
46 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UAGP300OU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
47

UAGP600VU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
48 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

UAGP600OU_B Pneumatic Power Pivot
UAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
49

LAGP Series Pneumatic Power Pivot
Features
• Available in three different sizes
• Four standard opening angles available
• Optional integrated stopping brake
• Saddle is chrome-plated steel that has a precision
ground surface and is case hardened
• Linear motion guided by roller bearings and
hardened steel guide
• Rotary motion guided by conical roller bearings
• External pre-stop assures accuracy and
repeatability of saddle
• Remains locked in closed position even when air
pressure is removed
• Unique "programmable" all metal sensor with M12
swivel connector
General Specifications
Weight:
LAGP170: 23 Kg (50.7 lbs)
LAGP300: 35 Kg (77.2 lbs)
LAGP600: 52 Kg (114.6 lbs)
Operating Pressure:
Minimum: 2.75 Bar (40 PSI)
Maximum: 8 Bar (115 PSI)
Note: Brake requires minimum pressure of 4.5 Bar (65 PSI)
How to Order
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles: 45º, 60º, 90º, 120º
Holding Capacity
LAGP170: 4000 Nm (2950 ft-lbs)
LAGP300: 6000 Nm (4425 ft-lbs)
LAGP600: 8000 Nm (5900 ft-lbs)
LAG
P
300
V U
090 B
Series
LAGP = Universal Power Pivot
with predetermined
pivot rotation in degrees
Version
P = Pneumatic
Size
170
300
600
Table Position
V =Vertical 180º
O = Horizontal 90º
Z = Vertical mount style symmetrical to V mount style
Max. opening angle 120º
P = Horizontal mount style symmetrical to O mount style
Max. opening angle 60º
Brake System
B = With safety brake
W = Without safety brake
Pivot Rotation in Degrees
120 = 120º
090 = 90º
060 = 60º
045 = 45º
Sensing Style
U = Electronic 24 VDC sensor with M12 swivel connector
50 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGP Series Pneumatic Power Pivot
Maximum Applicable Load
1200
1150
1100
1050
1000
900
English
operating pressure : 60 PSI
LAGP600
LAGP300
LAGP170
Load Capacity (lb)
850
800
750
700
650
600
550
500
450
400
350
300
250
200
150
100
50
0
4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
Distance from pivot point to load C.G. ( in )
500
475
450
425
400
375
Metric
operating pressure : 4 bar
LAGP600
LAGP300
LAGP170
Load Capacity (kg)
350
325
300
275
250
225
200
175
150
125
100
75
50
25
0
100 200 300 400 500 600 700 800 900 1000
Distance from pivot point to load C.G. ( mm )
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
51

LAGP Series Pneumatic Power Pivot
LAGP170VU___ B Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
52 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGP170OU___B Pneumatic Power Pivot
LAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
53

LAGP Series Pneumatic Power Pivot
LAGP300VU___B Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
54 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGP300OU___B Pneumatic Power Pivot
LAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
55

LAGP Series Pneumatic Power Pivot
LAGP600VU___B Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
56 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGP600OU___B Pneumatic Power Pivot
LAGP Series Pneumatic Power Pivot
conforming
* : TOLERANCE BETWEEN DOWEL HOLES ± 0.02, TO SCREW HOLES ± 0.1
** : TO BE ORDERED SEPARATELY
*** : AREA TO ACCESS THE MANUAL UNBLOCKING OF THE SAFETY BRAKE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
57

Electronic 24 VDC Sensor Cartridge
Electronic Sensors & Wishbone Arms
Model Number
UNP50 Clamp
UNP63 Clamp
UNP80 Clamp
UBP40 Clamp
UBP50 Clamp
UBP63 Clamp
UBP80 Clamp
UGP40 Gripper
LSP50 Pin Clamp
LTP50 Pin Clamp
UAGP170 Power Pivot
UAGP300 Power Pivot
UAGP600 Power Pivot
LAGP170 Power Pivot
LAGP300 Power Pivot
LAGP600 Power Pivot
Sensor Cartridge Part Number
DF-UB
DF-UB
DF-UBO170
DF-UB
DF-UB
DF-UB
DF-UBO170
DF-UB
DF-USGU
DF-USGU
DF-UBO170
DF-UO300
DF-UO600
DF-UBO170
DF-UO300
DF-UO600
UBP Series Standard Wishbone Arms
Model Number
UBP40 Central Arm
UBP40 Right Arm
UBP40 Left Arm
UBP50 Central Arm
UBP50 Right Arm
UBP50 Left Arm
UBP63 Central Arm
UBP63 Right Arm
UBP63 Left Arm
UBP80 Central Arm
UBP80 Right Arm
UBP80 Left Arm
Sensor Cartridge Part Number
LKP01CST
LKP01DST
LKP01SST
LKP00CL
LKP00DL
LKP00SL
LKP00CL
LKP00DL
LKP00SL
LKP80C
LKP80D
LKP80S
58
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LNE Series Electric Power Clamp
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connectors
• Modular electronics for ease of maintainability
• Single or dual cable control option
• Built in "obstruction" detection
• Integral brake maintains arm position any time
power is lost
• Mechanical indicator identifies when clamp
mechanism is locked
• Powered and unpowered manual override
• Adjustable opening angle
• Conforms to NAAMS Standards
• Blade and foot mounting
• Unique linkage design ensures positional
repeatability
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when
power is removed
General Specifications
Weight:
LNE 225: 3.9 Kg (8.6 lbs)
LNE350: 3.9 Kg (8.6 lbs)
LNE950: 11.5 Kg (25.4 lbs)
Operating Temperature: 5˚ to 40˚ C (40˚ to 105˚F)
Class Protection: IP65
Opening Angles:
15˚, 30˚,45˚, 60˚, 75˚, 90˚, 105˚, 120˚, 130˚
Holding Capacity:
LNE 225: 1250 Nm (11063 in-lbs)
LNE350: 1750 Nm (15488 in-lbs)
LNE950: 4000 Nm (35402 in-lbs)
How to Order
LNE 350 N N 21
Series
LNE = Electric Power Clamp
Size
225
350
950
Clamping Arm
N = Without Arm
Control Module
11 = Single M12 male 8 pin connector
In the case of an obstruction the arm stops in the position it is in.
12 = Single M12 male 8 pin connector
In the case of an obstruction the arm returns to its previous position.
21 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm stops in the position it is in.
22 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm returns to its previous position.
Output Shaft
N = Dual Shaft
L = Left Side Only
R = Right Side Only
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
59

Maximum Applicable Load
LNE Series Electric Power Clamp
English
Metric
34
16
32
30
LNE950
LNE350
LNE225
15
14
LNE950
LNE350
LNE225
28
26
*Note: Total weight and center
of gravity calculations must
include the weight of the arm.
13
12
*Note: Total weight and center
of gravity calculations must
include the weight of the arm.
24
11
22
Load capacity (lb)
20
18
16
14
Load capacity (Kg)
10
9
8
7
12
6
10
5
8
4
6
3
4
2
2
1
0
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Distance from pivot point to load C.G. ( in )
0
100 150 200 250 300 350 400 450
Distance from pivot point to load C.G. ( mm )
60 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Maximum Clamping Torque
LNE Series Electric Power Clamp
English
Metric
9000
2050
8500
2000
8000
LNE950
LNE350
1050
1000
7500
7000
LNE225
950
900
LNE950
Clamping Torque (in-lb)
6500
6000
5500
5000
4500
4000
3500
Clamping Torque [Nm]
850
800
750
700
650
600
550
500
450
LNE350
LNE225
3000
400
2500
350
300
2000
250
1500
200
1000
150
500
100
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [˚]
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [°]
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
61

LNE225N___ Electric Power Clamp
LNE Series Electric Power Clamp
Right Shaft
Left Shaft
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
The quotas in the panel refer to NAAMS norms
62 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LNE350N___ Electric Power Clamp
LNE Series Electric Power Clamp
Right Shaft
Left Shaft
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
The quotas in the panel refer to NAAMS norms
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
63

LNE950N___ Electric Power Clamp
LNE Series Electric Power Clamp
Right Shaft
Left Shaft
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
The quotas in the panel refer to NAAMS norms
64 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LNE225 - NAAMS Arm - Straight
LNE Series Electric Power Clamp
OAL REF
‘A’
15.00
19.0 SQ.
15.00
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP.
SCR HOLES
20.03
19.97
10.000 DWL
10.00 SCR
M6 x 1.0 THRU
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N206M ACA206M 90.0 80.00 65.00 50.00 110.0 0.4 (0.9)
N207M ACA207M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.5 (1.1)
N208M ACA208M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.6 (1.3)
LNE225 - NAAMS Arm - 25mm Offset
OAL REF
‘A’
50.00
19.0 SQ.
25.00
34.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP.
SCR HOLES
20.03
19.97
10.000 DWL
10.00 SCR
M6 x 1.0 THRU
20MM DP
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N216M ACA216M 90.0 80.00 65.00 50.00 110.0 0.5 (1.1)
N217M ACA217M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.6 (1.3)
N218M ACA218M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.7 (1.5)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
65

LNE225 - NAAMS Arm - 50mm Offset
LNE Series Electric Power Clamp
OAL REF
‘A’
75.00
50.00
19.0 SQ.
34.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
10.000 DWL
10.00 SCR
Ø11.0 TYP.
SCR HOLES
20.03
19.97
M6 x 1.0 THRU
20MM DP
Ø8 (F7) TYP. DOWEL HOLES
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
OAL
(REF)
WEIGHT
Kg (lbs)
N226M ACA226M 90.0 80.00 65.00 50.00 110.0 0.6 (1.3)
N227M ACA227M 120.0 110.00 95.00 80.00 65.00 50.00 140.0 0.7 (1.5)
N228M ACA228M 150.0 140.00 125.00 110.0 95.00 80.00 65.00 50.00 170.0 0.8 (1.7)
LNE350 - NAAMS Arm - Straight
22 SQ.
OAL REF
‘A’
18.0
15.0
‘J’
‘K’
‘I’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25THRU
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.50 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N007M ACA007M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.2 (2.6)
N008M ACA008M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.4 (3.0)
N009M ACA009M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.6 (3.5)
N010M ACA010M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.9 (4.2)
N011M ACA011M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.1 (4.6)
N012M ACA012M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.3 (5.0)
66 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LNE350 - NAAMS Arm - 25mm Offset
LNE Series Electric Power Clamp
55.0
25.0
50.0
‘K’
‘J’
‘I’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.50 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
OAL REF
‘A’
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N019M ACA019M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.1 (2.4)
N020M ACA020M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.3 (2.8)
N021M ACA021M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.4 (3.0)
N022M ACA022M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.5 (3.3)
N023M ACA023M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 1.6 (3.5)
N024M ACA024M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 1.9 (4.2)
LNE350 - NAAMS Arm - 70mm Offset
70.0
100.0
22 SQ.
50.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
‘K’
Ø11.0 TYP
SCR HOLES
25.03
24.97
M8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.500 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N031M ACA031M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.5 (3.3)
N032M ACA032M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 1.7 (3.7)
N033M ACA033M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 1.7 (3.7)
N034M ACA034M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 1.9 (4.2)
N035M ACA035M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.0 (4.4)
N036M ACA036M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.2 (4.8)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
67

LNE350 - NAAMS Arm - 120mm Offset
LNE Series Electric Power Clamp
OAL REF
‘A’
120.0
150.0
22 SQ.
50.0
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
‘K’
Ø11.0 TYP
SCR HOLES
25.03
24.97
m8 x 1.25
20mm DP
Ø8 (F7) TYP.
DOWEL HOLES
12.500 DWL
12.500 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
LNE950 - NAAMS Arm - Straight
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
OAL
(REF)
WEIGHT
Kg (lbs)
N043M ACA043M 135.0 125.00 110.00 95.00 80.00 65.00 163.0 1.9 (4.2)
N044M ACA044M 165.0 155.00 140.00 125.00 110.00 95.00 80.00 193.0 2.0 (4.4)
N045M ACA045M 195.0 185.00 170.00 155.00 140.00 125.00 110.00 80.00 223.0 2.1 (4.6)
N046M ACA046M 225.0 215.00 200.00 185.00 170.00 155.00 140.00 110.00 80.00 253.0 2.2 (4.8)
N047M ACA047M 255.0 245.00 230.00 215.00 200.00 185.00 170.00 140.00 110.00 80.00 283.0 2.4 (5.3)
N048M ACA048M 285.0 275.00 260.00 245.00 230.00 215.00 200.00 170.00 140.00 110.00 80.00 313.0 2.6 (5.7)
30 SQ.
OAL REF
‘A’
24.0
70.0
20.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
M10 x 1.5 THRU Ø8 (F7) TYP. DOWEL HOLES 16.000 DWL
16.00 SCR
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N110M ACA110M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 1.9 (4.2)
N111M ACA111M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.2 (4.8)
N112M ACA112M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.5 (5.5)
N113M ACA113M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 2.8 (6.2)
N114M ACA114M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.1 (6.8)
N115M ACA115M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.4 (7.5)
N116M ACA116M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.8 (8.4)
N117M ACA117M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.1 (9.0)
N118M ACA118M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.4 (9.7)
68 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LNE Series Electric Power Clamp
LNE950 - NAAMS Arm - 25mm Offset
OAL REF
‘A’
30 SQ.
60.0
25.0
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N130M ACA130M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.1 (4.6)
N131M ACA131M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.3 (5.0)
N132M ACA132M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.6 (5.7)
N133M ACA133M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 2.8 (6.2)
N134M ACA134M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.1 (6.8)
N135M ACA135M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.3 (7.3)
N136M ACA136M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.6 (7.9)
N137M ACA137M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 3.8 (8.4)
N138M ACA138M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.1 (9.0)
LNE950 - NAAMS Arm - 70mm Offset
OAL REF
‘A’
30 SQ.
70.0
105.0
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5 THRU
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N150M ACA150M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.4 (5.3)
N151M ACA151M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 2.6 (5.7)
N152M ACA152M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 2.9 (6.4)
N153M ACA153M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 3.1 (6.8)
N154M ACA154M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.4 (7.5)
N155M ACA155M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 3.6 (7.9)
N156M ACA156M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 3.9 (8.6)
N157M ACA157M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.1 (9.0)
N158M ACA158M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.4 (9.7)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
69

LNE Series Electric Power Clamp
LNE950 - NAAMS Arm - 120mm Offset
OAL REF
‘A’
30 SQ.
155.0
120.0
70.0
‘L’
‘M’
‘N’
‘K’
‘B’
‘C’
‘D’
‘E’
‘F’
‘G’
‘H’
‘I’
‘J’
Ø11.0 TYP
SCR HOLES
32.03
31.97
M10 x 1.5 THRU
20mm DP
Ø8 (F7) TYP. DOWEL HOLES
16.000 DWL
16.00 SCR
PART
NO.
NAAMS
CODE
DIM 'A'
+1.5/-0
DIM
'B'
DIM
'C'
DIM
'D'
DIM
'E'
DIM
'F'
DIM
'G'
DIM
'H'
DIM
'I'
DIM
'J'
DIM
'K'
DIM
'L'
DIM
'M'
DIM
'N'
OAL
(REF)
WEIGHT
Kg (lbs)
N170M ACA170M 155.0 145.00 130.00 115.00 100.00 85.00 192.0 2.8 (6.2)
N171M ACA171M 185.0 175.00 160.00 145.00 130.00 115.00 100.00 222.0 3.0 (6.6)
N172M ACA172M 215.0 205.00 190.00 175.00 160.00 145.00 130.00 100.00 252.0 3.3 (7.3)
N173M ACA173M 245.0 235.00 220.00 205.00 190.00 175.00 160.00 130.00 100.00 282.0 3.5 (7.7)
N174M ACA174M 275.0 265.00 250.00 235.00 220.00 205.00 190.00 160.00 130.00 100.00 312.0 3.8 (8.4)
N175M ACA175M 305.0 295.00 280.00 265.00 250.00 235.00 220.00 190.00 160.00 130.00 100.00 342.0 4.0 (8.8)
N176M ACA176M 335.0 325.00 310.00 295.00 280.00 265.00 250.00 220.00 190.00 160.00 130.00 100.00 372.0 4.3 (9.5)
N177M ACA177M 365.0 355.00 340.00 325.00 310.00 295.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 402.0 4.5 (9.9)
N178M ACA178M 395.0 385.00 370.00 355.00 340.00 325.00 310.00 280.00 250.00 220.00 190.00 160.00 130.00 100.00 432.0 4.8 (10.6)
70 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAE Series Electric Power Clamp
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connectors
• Modular electronics for ease of maintainability
• Single or dual cable control option
• Built in "obstruction" detection
• Integral brake maintains arm position any time power
is lost
• Mechanical indicator identifies when clamp
mechanism is locked
• Powered and unpowered manual override
• Adjustable opening angle
• Blade and foot mounting
• Unique linkage design ensures positional repeatability
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when power
is removed
General Specifications
Weight:
LAE140: 2.5 Kg (5.5 lbs)
Operating Temperature: 5˚ to 40˚ C (40˚ to 105˚F)
Class Protection: IP65
Opening Angles:
15˚, 30˚,45˚, 60˚, 75˚, 90˚, 105˚, 120˚,
Holding Capacity:
LAE140: 600 Nm (5310 in-lbs)
How to Order
LAE 140 V C 10
Series
LAE = Power Clamp
Size
140
Arm Mount Position
V = 90º
O = 180º
Control Module
11 = Single M12 male 8 pin connector
In the case of an obstruction the arm stops in the position it is in
12 = Single M12 male 8 pin connector
In the case of an obstruction the arm returns to its previous position
21 = Two M12 male 4 pin connectors (sensor/command)
In the case of an obstruction the arm stops in the position it is in
22 = Two M12 male 4 pin connectors (sensor/command)
In the case of an obstruction the arm returns to its previous position
Arm Style
C = Central - standard
D = Right - standard
S = Left - standard
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
71

Maximum Applicable Load
LAE Series Electric Power Clamp
English
Metric
8
4
LAE140
LAE140
Load capacity (lb)
6
4
2
Load capacity (Kg)
3
2
1
0
4 5 6 7 8 9 10 11 12
Distance from pivot point to load C.G. ( in )
0
100 150 200 250 300
Distance from pivot point to load C.G. ( mm )
Maximum Clamping Torque
English
Metric
2500
300
Clamping Torque (in-lb)
2000
1500
1000
500
LNE140
Clamping Torque (Nm)
250
200
150
100
50
LNE140
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [˚]
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Position of clamp arm [°]
72 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAE140V___Electric Power Clamp
LAE Series Electric Power Clamp
Area to access
electronics
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
73

LAE140O___Electric Power Clamp
LAE Series Electric Power Clamp
Area to access
electronics
74 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LGE Series Electric Gripper
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connectors
• Modular electronics for ease of maintainability
• Single or dual cable control option
• Built in "obstruction" detection
• Integral brake maintains arm position any time
power is lost
• Mechanical indicator identifies when gripper
mechanism is locked
• Powered and unpowered manual override
• Single and Double Moving Jaws
• Single and Double Tips
• Adjustable opening angle
• Linear and rotary motion guided by roller bearings
• Remains locked in closed position even when
power is removed
How to Order
General Specifications
Weight:
LGE140: 2.5 Kg (5.5 lbs)
Operating Temperature: 5˚ to 40˚ C (40˚ to 105˚F)
Class Protection: IP65
Opening Angles:
LGE140VB: 15˚, 30˚,45˚, 60˚, 75˚
LGE140VF: 15˚, 30˚,45˚, 60˚, 75˚
LGE140VL: 15˚, 30˚,45˚, 60˚, 75˚, 90˚
LGE140OL: 15˚, 30˚,45˚
*see dimensional drawings for more information.
Holding Capacity: 600 Nm (5310 in-lbs)
Maximum Grip Force:
LGE140V: 2333 N (525 lbs)
LGE140O: 1866 N (420 lbs)
LGE 140 V L 21
Series
LGE = Electric Gripper
Size
140
Jaw Mounting Position
V = 90°
O = 180°
*See dimensional drawings for more information
Control Module
11 = Single M12 male 8 pin connector
In the case of an obstruction the arm stops in the position it is in.
12 = Single M12 male 8 pin connector
In the case of an obstruction the arm returns to its previous position.
21 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm stops in the position it is in.
22 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm returns to its previous position.
Jaws Style
B = Upper and lower jaws opening; double tips - available only with
V jaws mount style.
F = Upper and lower jaws opening; single tips - available only with
V jaws mount style.
L = Fixed lower, upper jaw opening; double tips.
O
V
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
75

LGE140VB__ Electric Gripper
LGE Series Electric Gripper
Opening Angles
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
Datum Opening
Angle
A
Angle
B
Angle
15° 15° 3°
30° 30° 14°
45° 45° 29.5°
60° 60° 44°
75° 75° 58°
76 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LGE140VF__ Electric Gripper
LGE Series Electric Gripper
Opening Angles
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
Datum Opening
Angle
A
Angle
B
Angle
15° 15° 3°
30° 30° 14°
45° 45° 29.5°
60° 60° 44°
75° 75° 58°
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
77

LGE140VL__ Electric Gripper
LGE Series Electric Gripper
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
78 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LGE140OL__ Electric Gripper
LGE Series Electric Gripper
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
79

LSE Series Electric Pin Clamp
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connectors
• Modular electronics for ease of maintainability
• Single or dual cable control option
• Powered and unpowered manual override
• Locate and clamp material
• Multiple pin sizes available
• Orthogonal version for applications with very
demanding dimensional limitations
• Different working heights available
• Unique system prevents weld slag from
entering unit
• Hardened pins, hooks and scrapers for
extended life
• Remains locked in closed position even when
power is removed
How to Order
General Specifications
Weight:
LSE4G: 4 Kg (8.8 lbs)
LSE4U: 3.3 Kg (7.3 lbs)
Operating Temperature: 5˚ to 40˚ C (40˚ to 105˚F)
Class Protection: IP65
Maximum Clamping Force:
LSE4G: 3500 (786 lbs)
LSE4U: 4000N (899 lbs)
LSE 4 _ 3 1 0 21 _ _
Series
LSE = Electric Pin Clamp
Size
4
Model
G = Inline
U = Orthogonal
Pin Diameter
2 = Ø 20 mm
3 = Ø 25 mm
4 = Ø 30 mm
5 = Ø 35 mm
Different diameters upon request.
Pin
0 = No pin
1 = With pin
Progressive Numbering
Progressive numbering for special products
assigned by Sales Dept.
Control Module
11 = Single M12 male 8 pin connector
In the case of an obstruction the arm
stops in the position it is in.
12 = Single M12 male 8 pin connector
In the case of an obstruction the arm
returns to its previous position.
21 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm
stops in the position it is in.
22 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm
returns to its previous position.
Working Height
0 = Standard
Different working height upon request.
80 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LSE4G_10__ Electric Pin Clamp
LSE Series Electric Pin Clamp
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
ØD 20 25 30 35 40
L1 19 21.5 24 26.5 29
H 45 50 50 50 56
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
81

LSE4G_O___ Electric Pin Clamp
LSE Series Electric Pin Clamp
ØD 20 25 30 35 40
L1 19 21.5 24 26.5 29
* : TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
82 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LSE4U_10__ Electric Pin Clamp
LSE Series Electric Pin Clamp
Area to access
electronics
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
ØD 20 25 30 35
L1 17.5 20 22.5 25
H 23 23 30 30
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
83

LSE4U_O___ Electric Pin Clamp
LSE Series Electric Pin Clamp
Area to access
electronics
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
ØD 20 25 30 35
L 17.5 20 22.5 25
84 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LTE Series Electric Pin Clamp
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connectors
• Modular electronics for ease of maintainability
• Single or dual cable control option
• Powered and unpowered manual override
• Multiple pin sizes available
• Vanishing hook provides law profile
• Unique system prevents weld slag from
entering unit
• Long travel of hook designed for increased
engagement of sheet metal in oval slots
• Hardened pins, hooks and scrapers
for extended life
• Remains locked in closed position even when
power is removed
General Specifications
Weight:
LTE4T: 4.1 Kg (9 lbs)
Operating Temperature: 5˚ to 40˚ C (40˚ to 105˚F)
Class Protection: IP65
Maximum Clamping Force:
LTE4T: 3500 N (786 lbs)
How to Order
LTE 4 T 2 0 0 21 _ _
Series
LTE = Electric Pin Clamp with Vanishing Hook
Size
4
Model
T = With vanishing hook
Pin Diameter
2 = Ø 20 mm
3 = Ø 25 mm
4 = Ø 30 mm
5 = Ø 35 mm
6 = Ø 40 mm
Different diameters upon request.
Pin
0 = No pin
1 = With pin
Progressive Numbering
Progressive numbering for special products
assigned by Sales Dept.
Control Module
11 = Single M12 male 8 pin connector
In the case of an obstruction the arm
stops in the position it is in.
12 = Single M12 male 8 pin connector
In the case of an obstruction the arm
returns to its previous position.
21 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm
stops in the position it is in.
22 = Two M12 male 4 pin connector (sensor/command)
In the case of an obstruction the arm
returns to its previous position.
Working Height
0 = Standard
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
85

LTE Series Electric Pin Clamp
LTE4T_10__ Electric Pin Clamp with Vanishing Hook
Area to access
electronics
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
ØD 20 25 30 35 40
86 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LTE Series Electric Pin Clamp
LTE4T_0___ Electric Pin Clamp with Vanishing Hook
Area to access
electronics
*: TOLERANCE FOR DOWEL HOLES ± 0.02
FOR SCREW HOLES ± 0.1
ØD 20 25 30 35 40
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
87

LAGE Series Electric Power Pivot
Features
• Simple 24 VDC Digital Control (2 in / 2 out) via
standard M12 connector
• No PLC required to control motion
• Modular electronics for ease of maintainability
• Control module can be mounted on left side, right
side or remotely
• Manually adjustable opening angle
• Saddle is chrome-plated steel that has a precision
ground surface and is case hardened
• Integral brake maintains position any time power is lost
• Unpowered manual override
• Linear motion guided by roller bearings and
hardened steel guide
• Rotary motion guided by conical roller bearings
• External pre-stop assures accuracy and
repeatability of saddle
• Remains locked in closed position even when
power is removed
General Specifications
Weight:
LAGE0500V: 53 Kg (116.9 lbs)
LAGE0500O: 53 Kg (116.9 lbs)
LAGE1000V: 66.5 Kg (146.6 lbs)
LAGE1000O: 66.5 Kg (146.6 lbs)
LAGE0500VR: 39 Kg (86.0 lbs)
LAGE0500OR: 39 Kg (86.0 lbs)
LAGE1000VR: 52.5 Kg (115.8 lbs)
LAGE1000OR: 52.5 Kg (115.8 lbs)
LKMOSC Remote Control Module: 14 Kg (30.9 lbs)
Operating Temperature: 5˚ to 45˚ C (40˚ to 113˚F)
Class Protection: IP65
Opening Angles: 45˚, 60˚, 90˚, 120˚
Holding Capacity:
LAGE0500: 6000 Nm (4425 ft-lbs)
LAGE1000: 8000 Nm (5900 ft-lbs)
How to Order
LAGE 0500 V D 1
Series
LAGE = Power Pivot
Size
0500
1000
Pivot Mount Style
V = 90˚
O = 180˚
Voltage
O = 400 V ac
1 = 480 V ac
Control Module Position
D = Right Side
S = Left Side
R = Remote - cable to be ordered separately
88 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGE Series Electric Power Pivot
Maximum Applicable Load
Maximum applicable load (lb)
2400
2300
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
English
LAGE1000
LAGE0500
0
4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
1050
Distance from pivot point to load ( in )
Metric
1000
900
850
LAGE1000
LAGE0500
800
750
Maximum applicable load (kg)
700
650
600
550
500
450
400
350
300
250
200
150
100
50
0
100 200 300 400 500 600 700 800 900 1000
Distance from pivot point to load ( mm )
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
89

LAGE0500V__ Electric Power Pivot
LAGE Series Electric Power Pivot
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : MANUAL OPERATION: COVER KEY =5, KEY TO MOVE THE TABLE =10
*** : SPACE FOR MANUAL OPERATIONS
**** : SPACE FOR OPERATING ON THE ELECTRONIC COMPONENTS
***** : ROOM FOR CONNECTORS
****** : CONTROL UNIT MOUNTING POSITION : D=RIGHT ; S=LEFT
90 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGE 0500O__ Electric Power Pivot
LAGE Series Electric Power Pivot
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : MANUAL OPERATION: COVER KEY =5, KEY TO MOVE THE TABLE =10
*** : SPACE FOR MANUAL OPERATIONS
**** : SPACE FOR OPERATING ON THE ELECTRONIC COMPONENTS
***** : ROOM FOR CONNECTORS
****** : CONTROL UNIT MOUNTING POSITION : D=RIGHT ; S=LEFT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
91

LAGE1000V__ Electric Power Pivot
LAGE Series Electric Power Pivot
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : MANUAL OPERATION: COVER KEY =5, KEY TO MOVE THE TABLE =10
*** : SPACE FOR MANUAL OPERATIONS
**** : SPACE FOR OPERATING ON THE ELECTRONIC COMPONENTS
***** : ROOM FOR CONNECTORS
****** : CONTROL UNIT MOUNTING POSITION : D=RIGHT ; S=LEFT
92 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

LAGE 1000 O__ Electric Power Pivot
LAGE Series Electric Power Pivot
* : TOLERANCE BETWEEN DOWELS ± 0.02, TO SCREW HOLES ± 0.1
** : MANUAL OPERATION: COVER KEY =5, KEY TO MOVE THE TABLE =10
*** : SPACE FOR MANUAL OPERATIONS
**** : SPACE FOR OPERATING ON THE ELECTRONIC COMPONENTS
***** : ROOM FOR CONNECTORS
****** : CONTROL UNIT MOUNTING POSITION : D=RIGHT ; S=LEFT
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
93

LAGE Series Electric Power Pivot
LKMOSC Remote Control Unit for LAGE0500 - LAGE1000
* : SPACE FOR OPERATING ON THE ELECTRONIC COMPONENTS
** : ROOM FOR CONNECTORS
*** : SPACE TO REMOTE THE CONTROL UNIT
Cable for the connection between the power pivot
and remote control unit.
Part Number
TZ-CVLAGE-050
TZ-CVLAGE-100
TZ-CVLAGE-150
TZ-CVLAGE-200
Length
5 meters
10 meters
15 meters
20 meters
94 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Electronic Clamp Cables
4 & 8 Pin 12mm (M12) Electric Clamp Cables
4 Pin Female Straight
2 Meter - TC0402MRX0000000
5 Meter - TC0405MRX0000000
4 Pin Female 90º
2 Meter - TD0402MRX0000000
5 Meter - TD0405MRX0000000
8 Pin Female Straight
2 Meter - TC0802MRX0000000
5 Meter - TC0805MRX0000000
4 Pin Male Straight to Female Straight
2 Meter - TA0402MR0TC04000
5 Meter - TA0405MR0TC04000
4 Pin Male Straight to Female 90º
2 Meter - TA0402MR0TD04000
5 Meter - TA0405MR0TD04000
8 Pin Male Straight to Female Straight
2 Meter - TA0802MR0TC04000
5 Meter - TA0805MR0TC04000
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
95

Notes
96 Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.

Notes
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
97

WORLD HEADQUARTERS
USA
Numatics, Incorporated
46280 Dylan Drive
Novi, Michigan 48377
P: 248-596-3200
F: 248-596-3201
Canada
Numatics, Ltd
P: 519-452-1777
F: 519-452-3995
Mexico
Numatics de Mexico S.A. de C.V.
P: 52-222-284-6176
F: 52-222-284-6179
For a comprehensive listing of all Numatics production and distribution facilities worldwide, visit:
www.numatics.com
© Numatics Inc. 2008
LT-G3Catalog 1.0
10M-TGI-12/08