TL-SG3424_V1_CLI Guide - TP-Link

More documents

Recommendations

Info

Chapter 28 Cluster Commands.............................................................................195 cluster ndp...........................................................................................................................195 cluster ntdp..........................................................................................................................196 cluster explore .....................................................................................................................197 cluster..................................................................................................................................197 cluster candidate .................................................................................................................198 cluster individual..................................................................................................................198 show cluster ndp..................................................................................................................199 show cluster ntdp.................................................................................................................199 show cluster neighbour........................................................................................................200 show cluster manage role....................................................................................................200 XI
Preface This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). The switch or TL-SG3210/TL-SG3216/TL-SG3424 mentioned in this Guide stands for TL-SG3210/TL-SG3216/TL-SG3424 JetStream L2 Managed Switch without any explanation. The three devices of TL-SG3210, TL-SG3216 and TL-SG3424 are sharing this Guide. For simplicity, we will take TL-SG3424 for example throughout this Guide. TL-SG3210, TL-SG3216 and TL-SG3424 just differ in the number of LED indicators and ports and all figures in this guide are of TL-SG3424. Overview of this Guide Chapter 1: Using the CLI Provide information about how to use the CLI, CLI Command Modes, Security Levels and some Conventions. Chapter 2: User Interface Provide information about the commands used to switch between five CLI Command Modes. Chapter 3: IEEE 802.1Q VLAN Commands Provide information about the commands used for configuring IEEE 802.1Q VLAN. Chapter 4: MAC-Based VLAN Commands Provide information about the commands used for configuring MAC-Based VLAN. Chapter 5: Protocol-Based VLAN Commands Provide information about the commands used for configuring Protocol-Based VLAN. Chapter 6: Voice VLAN Commands Provide information about the commands used for configuring Voice VLAN. Chapter 7: GVRP Commands Provide information about the commands used for configuring GVRP (GARP VLAN registration protocol). Chapter 8: Etherchannel Commands Provide information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). Chapter 9: User Manage Commands Provide information about the commands used for user management. Chapter 10: Binding Table Commands Provide information about the commands used for binding the IP address, MAC address, VLAN and the connected Port number of the Host together. Besides it also provide information about the 1
Page 1 and 2: TL-SG3210/TL-SG3216/TL-SG3424 JetSt
Page 3 and 4: CONTENTS Preface ..................
Page 5 and 6: user access-control mac-based......
Page 7 and 8: ip ssh download....................
Page 9 and 10: show qos status....................
Page 11: ip igmp snooping(interface) .......
Page 15 and 16: Provide information about the comma
Page 17 and 18: Figure 1-2 Connection Description 4
Page 19 and 20: Note: 1. Before Telnet login, you a
Page 21 and 22: Figure 1-10 Enter into the Privileg
Page 23 and 24: Now you can manage your switch with
Page 25 and 26: Users get the privilege to the User
Page 27 and 28: Chapter 2 User Interface enable Des
Page 29 and 30: Command Mode Example Any Configurat
Page 31 and 32: Parameter vlan-id —— Specify IE
Page 33 and 34: Parameter no switchport trunk allow
Page 35 and 36: show vlan brief Description Syntax
Page 37 and 38: Command Mode Parameter Example Priv
Page 39 and 40: protocol-vlan vlan Description Synt
Page 41 and 42: Chapter 6 Voice VLAN Commands Voice
Page 43 and 44: Syntax voice vlan mac-address mac-a
Page 45 and 46: show voice vlan oui Description The
Page 47 and 48: Example Enable the GVRP function fo
Page 49 and 50: Example Display the global GVRP sta
Page 51 and 52: port-channel load-balance Descripti
Page 53 and 54: Syntax show etherchannel [ channel-
Page 55 and 56: Chapter 9 User Manage Commands User
Page 57 and 58: Parameter mac-addr —— The sourc
Page 59 and 60: Parameter minutes ——The timeout
Page 61 and 62: Command Mode Line Configuration Mod
Page 63 and 64:
Chapter 10 Binding Table Commands Y
Page 65 and 66:
To restore to the default value, pl
Page 67 and 68:
ip dhcp snooping information remote
Page 69 and 70:
Syntax ip dhcp snooping mac-verify
Page 71 and 72:
show ip dhcp snooping Description T
Page 73 and 74:
Chapter 11 ARP Inspection Commands
Page 75 and 76:
ip arp inspection limit-rate Descri
Page 77 and 78:
TL-SG3424(config)# show ip arp insp
Page 79 and 80:
Parameter land —— Land attack.
Page 81 and 82:
pap: IEEE 802.1X authentication sys
Page 83 and 84:
Example Configure the quiet period
Page 85 and 86:
Syntax dot1x port-control { auto |
Page 87 and 88:
value ——The maximum time for th
Page 89 and 90:
Command Mode Privileged EXEC Mode a
Page 91 and 92:
logging file flash Description The
Page 93 and 94:
show logging local-config Descripti
Page 95 and 96:
Chapter 15 SSH Commands SSH (Securi
Page 97 and 98:
Command Mode Global Configuration M
Page 99 and 100:
Chapter 16 SSL Commands SSL(Secure
Page 101 and 102:
show ip http secure-server Descript
Page 103 and 104:
mac address-table aging-time Descri
Page 105 and 106:
status —— Enable or disable the
Page 107 and 108:
Syntax show mac address-table inter
Page 109 and 110:
Chapter 18 System Configuration Com
Page 111 and 112:
system-time dst predefined Descript
Page 113 and 114:
stime —— Time to start, in the
Page 115 and 116:
eset Description The reset command
Page 117 and 118:
name —— Specify the name for th
Page 119 and 120:
Example Test the connectivity betwe
Page 121 and 122:
show system-info Description The sh
Page 123 and 124:
User Guidelines Command in the Inte
Page 125 and 126:
Parameter full | half —— The du
Page 127 and 128:
Parameter rate —— Select the ba
Page 129 and 130:
show interface status Description T
Page 131 and 132:
show interface configuration Descri
Page 133 and 134:
Chapter 20 QoS Commands QoS (Qualit
Page 135 and 136:
User Guidelines 1. By default, the
Page 137 and 138:
equ —— Equal-Mode. In this mode
Page 139 and 140:
show qos status Description The sho
Page 141 and 142:
monitor session source interface De
Page 143 and 144:
Chapter 22 Port isolation Commands
Page 145 and 146:
Chapter 23 Loopback Detection Comma
Page 147 and 148:
TL-SG3424(config)# interface range
Page 149 and 150:
Command Mode Privileged EXEC Mode a
Page 151 and 152:
Parameter start-date —— The sta
Page 153 and 154:
Example Define National Day, config
Page 155 and 156:
255.255.255.0, the time-range for t
Page 157 and 158:
ethernet-type —— EtherType cont
Page 159 and 160:
policy to port 2: TL-SG3424(config)
Page 161 and 162:
Parameter dscp —— DSCP of QoS R
Page 163 and 164:
Syntax show holiday Command Mode Pr
Page 165 and 166:
Chapter 25 MSTP Commands MSTP (Mult
Page 167 and 168:
Command Mode Interface Configuratio
Page 169 and 170:
Remove VLANs 1-50 in maping VLANs 1
Page 171 and 172:
Parameter instance-id —— Instan
Page 173 and 174:
Parameter forward-time —— Forwa
Page 175 and 176:
Example Enable the BPDU filter func
Page 177 and 178:
emoving MAC address entries, which
Page 179 and 180:
Example Display the spanning-tree i
Page 181 and 182:
Chapter 26 IGMP Commands IGMP Snoop
Page 183 and 184:
ip igmp snooping vlan-config Descri
Page 185 and 186:
leave-time —— Leave Time, which
Page 187 and 188:
Syntax ip igmp snooping filter no i
Page 189 and 190:
Syntax show ip igmp snooping interf
Page 191 and 192:
Display the count of multicast entr
Page 193 and 194:
mib-oid —— MIB Object ID. It is
Page 195 and 196:
Parameter name —— User Name, ra
Page 197 and 198:
udp-port —— UDP port, which is
Page 199 and 200:
periodically, based on which the ma
Page 201 and 202:
f-hold ] [ falling-event-index f-ev
Page 203 and 204:
Syntax show snmp-server group Comma
Page 205 and 206:
for each command. By default, the c
Page 207 and 208:
Chapter 28 Cluster Commands Cluster
Page 209 and 210:
hop-value —— NTDP Hops, which i
Page 211 and 212:
show cluster ndp Description The sh
show all

TL-SG3424_V1_CLI Guide - TP-Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?