Butt Weld Fittings - Outokumpu

Butt Weld Fittings
OT 500
ISO
Collars PN10-PN16 in accordance with EN 13480 and EN 1092-1
Weight kg/pce / Design pressure bar
DN A Sp F d1 H5 EN 13480 1) EN 1092-1 type 37 2)
Butt Weld Fittings
10 17.2 2.0 2.5 40 7 0.02/16 0.02/16
15 21.3 2.0 2.5 45 7 0.03/16 0.03/16
20 26.9 2.0 3.0 58 8 0.06/16 0.06/16
3.0 4.0 8 0.07/16
25 33.7 2.0 3.0 68 10 0.08/16 0.08/16
3.2 4.0 10 0.10/16
32 42.4 2.0 3.0 78 12 0.10/16 0.10/16
3.2 4.0 12 0.13/16
40 44.5 2.0
Rev.1
3.0 88 17
R-154.SLDDRW
0.14/16 0.14/16
48.3 2.0 3.0 15 0.13/16 0.13/16
3.2 4.0 15 0.17/16
50 57.0 3.0 4.0 102 18 0.23/16
60.3 2.0 3.0 20 0.18/16 0.18/6
3.2 4.0 20 0.23/16 0.23/16
65 76.1 2.0 3.0 20 0.24/16 0.24/6
3.2 4.0 20 0.32/16
80 88.9 2.0 3.0 138 25 0.31/16
3.2 4.0 25 0.42/16 0.42/16
100 114.3 2.0 2.5 25 0.31/10
3.2 4.0 25 0.49/16 0.49/16
125 139.7 2.0 2.5 25 0.39/10
3.2 (3.5)* 4.0 25 0.64/16 0.64/16
150 168.3 2.0 2.5 212 25 0.47/10
3.0 3.5 25 0.64/10
3.2 (3.5)* 4.0 25 0.73/10 0.73/10
4.0 5.0 25 0.93/16
200 219.1 2.0 2.5 268 30 0.67/6
3.2 4.0 30 1.06/10
1) Design pressure is calculated for grade EN 1.4307 at 20 °C and fulfils the requirements
in EN 13480, Part 2, Part 3 and Part 5, EN 13445-3. Full face gasket with thickness ≥ 1.0 mm.
Gasket factor 3.50 and design seating stress ≥ 45 Mpa. See also appendix H in EN13445-3.
2) Collars according to EN 1092-1 are calculated according to EN 1591-1.
The designation of a EN 1092-1 DN 50 collar is: Collar EN 1092-1/37/60.3x2/PN16/1.4432/LotNo.
*) Corresponds to thickness S acc. to EN 1092-1.
Stock standard: EN 1.4307 and 1.4432
OT 500
ISO
Collars welded and pressed
DN A F=Sp d1 H5 Weight kg/pce / Design pressure bar
250 273.00 3 320 31 1.18/6
4 31 1.58/10
300 323.90 3 378 35 1.50/4
4 35 1.90/10
The pressures are calculated for grade EN 1.4307 at 20 °C. Full face gasket with thickness ≥ 1.5 mm.
Gasket factor 2.85 and design seating stress ≥ 30 Mpa. See also appendix H in EN 13445-3.
Stock standard: EN 1.4307 and 1.4432
62
Rev.1
R-154.SLDDRW

Butt Weld Fittings
OT 509
ISO
Collars welded and pressed (long neck)
DN A Sp=F d1 H5 Weight kg/pce / Design pressure bar
250 273 3 320 70 1.96/10
300 323.9 3 378 68 2.26/10
The pressures are calculated for grade En 1.4307 at 20 °C. Full-face gasket with thickness ≥1.5 mm.
Gasket factor 4.94 and design seating stress 90 MPa. Se also Appendix H in EN 13445-3.
Note! To obtain the pressure ratings in the table the collars are dimensioned for special flanges
that have less bore diameter and chamfer, and the other measures are at least the same
as corresponding EN 1092-1 flanges type 02.
Stock standard: EN 1.4307 and 1.4432
Rev.1
OT 510
Metric Tru-Bore ®
Collars according to EN 13480 and EN 1092-1
R-154.SLDDRW
Weight kg/pce / Design pressure bar
DN A Sp F d1 H5 EN 13480 1) EN 1092-1 type 37 2)
10 16 2.0 2.5 45 8 0.03/16 0.03/16
15 20 2.0 3.0 45 9 0.04/16 0.04/16
20 25 2.0 3.0 58 10 0.06/16 0.06/16
25 28 2.0 3.0 68 12 0.08/16 0.08/16
30 2.0 3.0 12 0.08/16 0.08/16
32 38 2.0 3.0 78 14 0.11/16 0.11/16
40 2.0 3.0 14 0.11/16 0.11/16
50 51 2.0 2.5 102 18 0.15/16 0.15/10
54 2.0 3.0 18 0.18/16 0.18/10
65 64 2.0 Rev.1 2.5 18 R-154.SLDDRW
0.14/16
69 2.0 3.0 122 20 0.25/16 0.25/10
70 2.0 3.0 20 0.25/16 0.25/10
71 3.0 4.0 124 20 0.35/16
74 2.0 3.0 22 0.26/16 0.26/10
76 3.0 4.0 22 0.34/16
79 2.0 3.0 138 23 0.32/16 0.32/10
DN = ID
80 81 3.2 4.0 138 23 0.42/16 0.42/16
84 2.0 3.0 24 0.32/16 0.32/10
86 3.2 4.0 24 0.42/16 0.42/16
100 102 2.0 2.5 158 27 0.33/10
104 2.0 2.5 27 0.33/10
106 3.2 4.0 27 0.52/16 0.52/10
108 4.0 5.0 27 0.68/25
125 129 2.0 2.5 188 27 0.44/6
131 3.0 4.0 27 0.69/16
133 4.0 5.0 27 0.91/16
150 154 2.0 2.5 212 27 0.51/2.5
156 3.0 4.0 27 0.80/10
158 4.0 5.0 27 1.00/16
200 204 2.0 2.0 268 26 0.56/2.5
206 3.0 3.0 26 0.83/6
208 4.0 4.0 26 1.10/10
Butt Weld Fittings
1) Design pressure is calculated for grade EN 1.4307 at 20 °C and fulfils the requirements
in EN 13480, Part 2, Part 3 and Part 5, EN 13445-3. Full face gasket with thickness ≥1.0 mm.
Gasket factor 3.50 and design seating stress ≥45 Mpa. See also appendix H in EN13445-3.
2) Collars according to EN 1092-1 are calculated according to EN 1591-1.
The designation of a EN 1092-1 DN 50 collar is: Collar EN 1092-1/37/54x2/PN10/1.4432/LotNo.
Stock standard: EN 1.4307 and 1.4432
63

Butt Weld Fittings
OT 510
Metric Tru-Bore ®
Collars welded and pressed
DN A Sp=F d1 H5 Weight kg/pce / Design pressure bar
250 255 2.5 320 31 1.00/4
256 3.0 320 31 1.20/6
300 305 2.5 370 35 1.75/4
306 3.0 370 35 1.50/4
350 355 2.5 430 43 1.60/4
356 3.0 430 43 2.20/4
400 406 3.0 482 43 2.50/2
408 4.0 482 43 3.30/4
450 456 Rev.13.0 532 45 R-154.SLDDRW 2.90/2
458 4.0 532 45 3.80/4
500 506 3.0 585 45 3.20/2
508 4.0 585 45 4.20/4
600 606 3.0 685 45 3.70/2
608 4.0 685 45 4.90/4
The pressures are calculated for grade En 1.4307 at 20 °C.
Full-face gasket with thickness ≥1.5 mm. Gasket factor 4.94 and design seating stress 90 MPa.
Se also Appendix H in EN 13445-3.
Stock standard: EN 1.4307 and 1.4432
Butt Weld Fittings
OT 519
Metric Tru-Bore ®
Collars welded and pressed (long neck)
DN A Sp=F d1 H5 Weight kg/pce / Design pressure bar
250 256 3 320 65 1.90/16*
300 306 3 370 55 2.00/16*
350 356 3 430 55 2.50/16*
400 408 4 482 65 4.20/10*
500 508 4 585 75 5.70/10*
600 608 4 685 80 7.20/10*
The pressures are calculated for grade En 1.4307 at 20 °C.
Full-face gasket with thickness 1.5 mm. Gasket factor 4.94 and
design seating stress 90 MPa. Rev.1
Se also Appendix H in EN 13445-3.
*) Note! To obtain the pressure ratings in the table the collars are
dimensioned for special flanges that have less bore diameter and
chamfer, and the other measures are at least the same as corresponding
EN 1092-1 flanges type 02.
Stock standard: EN 1.4307 and 1.4432
R-154.SLDDRW
Loose flanges NOMEKO 254DH
Dim. (mm) D1±2 (mm) Dh±1 (mm) di (mm) Ds±0.6 (mm) Screw No. screw F +3
-2 (mm)
256 395 350 269 -1 0
22 M20 12 26
306 445 400 330 -1.5 0
22 M20 12 26
356 505 460 369 -1.5 0
22 M20 16 30
408 565 515 425 -1.5 0
26 M20 16 34
508 670 620 524 -1.5 0
26 M20 20 40
608 780 725 624 -1.5 0
30 M20 20 45
64

Butt Weld Fittings
A
OT 502
ISO
Weldring necks PN 10 in accordance with EN 13480 (SSG 7465; EN 1092-1 Type 35; SFS 4167)
Weight
DN A d1 H4 F S T1 kg/pce
15-32 Use PN 40 (SSG 7468)
40-250 Use PN 16 (SSG 7466)
300 323.9 370 68 12 3.2 8.0 6.80
350 355.6 430 68 13 3.2 8.0 9.50
400 406.4 482 72 14 3.2 8.0 11.6
450 457 532 72 15 3.6 8.0 15.0
500 508 585 75 16 4.0 8.0 15.9
600 610 685 80 18 5.0 10 23.0
700 Re v.1 711 80 20 6.3 R-155I.SLDDRW 10 30.9
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
Stock standard: EN 1.4432 and EN 1.4301
A
OT 502
ISO
Weldring necks PN 16 in accordance with EN 13480 (SSG 7466; EN 1092-1 Type 35; SFS 4168)
Weight
DN A d1 H4 F S T1 kg/pce
15-40 Use PN 40 (SSG 7468)
50 60.3 102 45 8.0 2.0 3.0 0.53
65 76.1 122 45 8.0 2.0 4.0 0.70
80 88.9 138 50 8.0 2.0 4.0 1.00
100 114.3 158 52 10 2.0 4.0 1.30
125 139.7 188 55 10 2.0 5.0 1.90
150 168.3 212 55 10 2.0 6.0 2.40
200 219.1 268 62 11 2.6 6.0 3.90
250 273.0 Re v.1 320 70 12 3.2 R-155I.SLDDRW 8.0 5.80
300 323.9 378 78 14 4.0 10 9.50*
350 355.6 438 82 18 4.0 10 15.2*
400 406.4 490 85 20 5.0 12 18.7*
450 457 550 87 22 5.0 12 24.4*
500 508 610 90 22 6.3 12 29.1*
600 610 725 95 24 8.0 12 40.3*
Butt Weld Fittings
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
Stock standard: EN 1.4432 and EN 1.4301
*) No stock standard
65

Butt Weld Fittings
A
OT 502
ISO
Weldring necks PN 25 in accordance with EN 13480 (SSG 7467; EN 1092-1 Type 35; SFS 4169)
Weight
DN A d1 H4 F S T1 kg/pce
15-100 Use PN 40 (SSG 7468)
125 139.7 188 68 16 3.2 6 2.70*
150 168.3 218 75 18 3.2 8 3.50*
200 219.1 278 80 18 3.2 8 6.60*
250 273.0 335 88 18 5.0 10 10.0*
300 323.9 395 92 20 6.3 10 15.3*
350 355.6 450 100 22 6.3 12 20.8*
400 406.4 505 110 24 8 14 28.6*
450 457 Re v.1 555 110 26 8 R-155I.SLDDRW
34.4*
500 508 615 125 28 10 16 45.8*
600 610 720 115 30 10 18 61.0*
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
*) No stock standard
A
OT 502
ISO
Weldring necks PN 40 in accordance with EN 13480 (SSG 7468; EN 1092-1 Type 35; SFS 4170)
Butt Weld Fittings
Weight
DN A d1 H4 F S T1 kg/pce
15 21.3 45 38 5 2.0 3.0 0.09
20 26.9 58 40 6 2.0 3.0 0.17
25 33.7 68 40 7 2.0 3.0 0.26
32 42.4 78 42 8 2.0 3.0 0.36
40 48.3 88 45 8 2.0 3.0 0.45
50 60.3 102 48 10 2.6 4.0 0.69*
65 76.1 122 52 11 2.6 5.0 1.10*
80 88.9 138 58 12 2.6 6.0 1.60*
100 114.3 Re162 v.1
65 14 3.2 R-155I.SLDDRW 6.0 2.40*
125 139.7 188 68 16 3.2 6.0 3.20*
150 168.3 218 75 18 4.0 8.0 4.60*
200 219.1 285 88 20 5.0 10 8.80*
250 273.0 345 105 22 6.3 12 14.4*
300 323.9 410 115 25 8.0 12 20.7*
350 355.6 465 125 28 8.0 14 30.7*
400 406.4 535 135 32 10 16 45.4*
450 457.0 560 ** ** ** ** **
500 508.0 615 ** ** ** ** **
600 610.0 735 ** ** ** ** **
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
Stock standard: EN 1.4432 and EN 1.4301
*) No stock standard
**) Specified by the customer, no stock standard
66

Butt Weld Fittings
A
OT 512
Metric Tru-Bore ®
Weldring necks PN 10 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7365)
Weight
DN A d1 H4 F S T1 kg/pce
20-250 Use PN 16 (SSG 7366)
300 316 370 60 12 3.0 8.0 6.80
350 366 430 60 12 3.5 8.0 9.50
400 416 482 65 12 3.5 8.0 11.6*
450 466 532 70 15 3.5 8.0 15.0*
500 518 585 75 15 4.0 9.0 15.9*
600 620 685 80 15 4.0 10 23.0*
700 724 800 90 15 4.5 12 30.9*
800 826 Re v.1 905 100 15 5.0 R-155I.SLDDRW 13 41.5*
900 916 1005 110 18 6.0 15 50.0*
1000 1016 1110 120 18 8.0 18 58.9*
1200 1220 1330 130 22 10 18 93.2*
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
Stock standard: EN 1.4432
*) No stock standard
A
OT 512
Metric Tru-Bore ®
Weldring necks PN16 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7366)
Weight
DN A d1 H4 F S T1 kg/pce
20 24 58 40 6.0 2.0 2.0 0.17*
25 29 68 40 6.0 2.0 2.0 0.26*
32 36 78 40 6.0 2.0 2.0 0.36*
40 44 88 45 6.0 2.0 2.0 0.45
50 54 102 45 8.0 2.0 2.0 0.53
65 70 122 45 8.0 2.5 2.5 0.70
80 86 138 50 10 3.0 3.0 1.00
100 108 158 50 10 3.0 4.0 1.30
125 135 188 50 10 3.0 5.0 1.90
150 160 Re212 v.1
50 10 3.0 R-155I.SLDDRW 5.0 2.40
200 214 268 65 10 3.0 7.0 3.90
250 266 320 65 12 3.5 8.0 5.80
300 320 370 65 12 4.0 10 9.50*
350 370 430 70 15 4.5 10 15,2*
400 424 482 80 15 5.0 12 18.7*
450 474 532 85 15 5.0 12 24.4*
500 524 585 95 18 5.0 12 29.1*
600 628 685 100 18 6.0 14 40.3*
700 728 795 110 20 10 14 45.2*
800 832 900 110 22 12 16 59.9*
900 936 1000 115 24 12 18 75.6*
1000 1036 1115 130 32 15 18 106.45*
1200 1244 1330 130 32 15 22 130.5*
Butt Weld Fittings
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
Stock standard: EN 1.4432
*) No stock standard
67

Butt Weld Fittings
A
OT 512
Metric Tru-Bore ®
Weldring necks PN 25 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7367)
Weight
DN A d1 H4 F S T1 kg/pce
20-150 Use DN 20-150 (SSG 7370)
200 219 278 65 12 5.0 9 6.60*
250 274 335 75 15 6.5 10 10.0*
300 325 390 80 16 7.5 11.5 15.3*
350 374 450 85 18 5.0 12 20.8*
400 427 505 95 18 6.0 13.5 28.6*
450 480 555 105 20 8.0 15 34.4*
500 530 615 115 22 8.0 15 45.8*
600 636 Re v.1 720 115 24 12 R-155I.SLDDRW 18 61.0*
700 730 820 ** ** ** ** **
800 830 930 ** ** ** ** **
900 936 1030 ** ** ** ** **
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75.
*) No stock standard
**) Specified by the customer, no stock standard
A
OT 512
Metric Tru-Bore ®
Weldring necks PN 40 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7370)
Butt Weld Fittings
Weight
DN A d1 H4 F S T1 kg/pce
20 26 58 40 6 2.5 3.0 0.17
25 31 68 40 6 2.5 3.0 0.26
32 39 78 40 6 2.5 3.5 0.36
40 47 88 45 8 2.5 3.5 0.45*
50 58 102 45 8 2.5 4.0 0.69*
65 74 122 45 10 2.5 4.5 1.10*
80 89 138 55 10 2.5 4.5 1.60*
100 110 162 55 10 3.0 5.0 2.40*
125 137 Re v.1 188 55 12 3.5 R-155I.SLDDRW 6.0 3.20*
150 164 218 65 12 4.0 7.0 4.60*
200 220 285 85 20 6.0 10 8.80*
250 274 345 100 22 8.0 12 14.4*
300 330 410 110 24 9.0 15 20.7*
350 380 465 120 30 10 15 20.7*
400 440 535 130 30 12 20 45.4*
450 490 560 135 30 12 20 39.0*
500 540 615 140 35 15 20 49.0*
600 648 735 150 40 15 24 118.4*
Use with loose flange according to EN 1092-1 type 02. See illustration on page 75. Stock standard: EN 1.4432
*) No stock standard
68

Butt Weld Fittings
OT 501
ISO
Weld-on plate collars
Weight
DN d D T kg/pce
10 17.7 40 6.0 0.05
15 21.8 45 6.0 0.06
20 27.4 58 6.0 0.10
25 34.2 68 6.0 0.14
32 43.0 78 6.0 0.16
40 48.8 88 6.0 0.21
50 60.8 102 8.0 0.35
65 76.6 122 8.0 0.48
80 89.4 138 10 0.70
100 115.5 158 10 0.75
125 140.7 184 10 0.90
150 169.3 212 10 1.04
200 220.1 268 10 1.50
Stock standard: EN 1.4404 ≤ DN 80
EN 1.4432 > DN 80
OT 511
Metric Tru-Bore ®
Weld-on plate collars
Weight
DN d D T kg/pce
10 15.0 40 6.0 0.05
15 20.5 45 6.0 0.06
20 25.5 58 6.0 0.10
25 30.5 68 6.0 0.14
32 39.0 78 6.0 0.17
40 45.0 88 6.0 0.22
50 55.0 102 8.0 0.38
65 70.0 122 8.0 0.50
70 75.0 122 10 0.59
75 80.0 138 10 0.79
80 85.0 138 10 0.75
100 105.0 158 10 0.88
125 130.0 184 10 1.10
150 155.0 212 10 1.30
200 205.0 268 10 1.90
250 255.0 320 12 2.80
300 306.0 370 12 3.30
350 356.0 430 12 4.40
400 406.0 482 12 5.10
450 456 532 15 7.10
500 508 585 15 8.00
Butt Weld Fittings
Stock standard: EN 1.4404 ≤ DN 80
EN 1.4432 > DN 80
69

Butt Weld Fittings
Butt Weld Fittings
OT 503
ISO
Angle collars
OT 513
Metric Tru-Bore ®
Angle collars
R -153.SLDDRW Rev.1 2 R 003-11-17 -153.SLDDRW 2 003-11-17
presure
Weight
DN D1 T D H kg/pce / Design pressure bar
200 219.1 4 271 28 1.20/10
250 273.0 4 320 28 1.40/10
300 323.9 4 376 28 1.80/10
350 355.6 4 410 28 2.10/6
400 406.4 4 480 38 3.30/6
450 457 4 530 38 3.50/6
500 508 5 590 48 5.70/6
600 610 5 690 48 7.20/6
The pressures are calculated for grade EN 1.4307 at 20 °C.
Full face gasket with thickness ≥0.5 mm. Gasket factor 4.94 and design seating stress ≥90 Mpa.
See also appendix H in EN 13445-3.
Loose flange for dimension DN 200 - 300 and DN 500 - 600 SS 2049/DIN 2642/EN 1092-1 type 02 can be used.
For DN 350-450 use SS 2049/DIN2642.
.
The pressures are calculated for grade EN 1.4307 at 20 °C.
Full face gasket with thickness ≥0.5 mm. Gasket factor 4.94 and design seating stress ≥90 Mpa.
See also appendix H in EN 13445-3.
Loose flange for dimension DN 200 - 300 and DN 500-600 SS 2049/DIN 2642/EN 1092-1 type 02 can be used.
For DN 350 - 450 use SS 2049/DIN2642.
Stock standard: EN 1.4432
press ure
Weight
DN D1 T D H kg/pce / Design pressure bar
200 208 4 260 28 1.71 1.10
200 208 4 260 28 1.10/10
250 258 4 310 28 1.40/10
300 308 4 360 28 1.70/10
350 358 4 410 28 2.00/6
400 408 4 480 38 3.20/6
450 458 4 530 38 3.30/6
500 510 5 590 48 5.50/6
600 610 5 690 48 6.80/6
700 710 5 785 48 8.30/4
800 810 5 885 48 9.40/4
Stock standard: EN 1.4432
70