Compact / Hardwired / Logic Controller / M238 ... - Schneider Electric

More documents

Recommendations

Info

4 To configure an expansion module, double click on it. Here we will configure the analog output of the expansion module TM2AMM6HT. 5 In the I/O Configuration tab… 6 …the Value of the Enumeration of BYTE for the Type of QW0 is changed to 0..10 V. Press enter to accept the new selection. The Value of the Enumeration of BYTE for the Scope of QW0 can be selected between Normal (fixed min and max values) and Customized. Optimized HW M238 Schneider Electric 44
7 On the Extension Bus I/O Mapping tab it is possible to map the data of QW0 to a variable. There are two ways of Mapping: Create a new variable Mapping to an existing variable In this project, Map to existing variable was used, i.e. the output is mapped to an existing variable that is located in the folder Application → GVL. GVL stands for global variables list, which can be accessed throughout Application. The GVL is opened by double clicking on GVL in the Devices window. In this application, q_wAtv12SpdRef is declared as a WORD variable in the Application’s GVL (Application.GVL.q_wAtv12 SpdRef). 8 To map the output to an existing variable, double click on the output Variable field then click on the … button that appears at the end of the field. In the Input Assistant dialog that opens, locate the variable inside the Global Variables category and select it. Then click OK. Optimized HW M238 Schneider Electric 45
Page 1 and 2: This document is based on European
Page 3 and 4: Important Information NOTICE Read t
Page 5 and 6: CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8: Abbreviations Abbreviation AC CB CF
Page 9 and 10: Application Source Code Introductio
Page 11 and 12: System Introduction The system chap
Page 13 and 14: Functional Safety Notice (EN ISO 13
Page 15 and 16: Main cabinet interior Optimized HW
Page 17 and 18: Hardware General General descriptio
Page 19 and 20: Controller Modicon M238 Logic contr
Page 21 and 22: TM2 I/O Module TM2AMM6HT 4 Analog I
Page 23 and 24: Contactor TeSysD LC1D09BD Variable
Page 25 and 26: Servo Drive Lexium 32C LXM32CD18M2
Page 33 and 34: Limit Switch OsiSense XCKP2118P16 O
Page 35 and 36: Communication General The Modicon M
Page 37 and 38: Implementation Introduction The imp
Page 39 and 40: Communication Introduction This cha
Page 41 and 42: Create a new project 1 To create a
Page 43: 3 The Devices folder display now th
Page 47 and 48: 2 In the PTO 0 tab… 3 …the Valu
Page 49 and 50: Inputs/Outputs tab Graphical tab Do
Page 51 and 52: Add TeSys Library 1 In this applica
Page 53 and 54: 5 More information on the TeSys lib
Page 55 and 56: 7 To instantiate the FB, click on ?
Page 57 and 58: 12 The VAR_GLOBAL variables are loc
Page 59 and 60: 2 In the Add Device dialog, select
Page 61 and 62: 2 Select Symbol configuration in th
Page 63 and 64: Communication Settings Controller
Page 65 and 66: 3 During the scan, the Scan network
Page 67 and 68: Download the controller and HMI pro
Page 69 and 70: 8 Check the controller (MyControlle
Page 71 and 72: 4 To start running the Application
Page 73 and 74: 2 In the SoMachine - Network Equipm
Page 75 and 76: 4 In the Variables List dialog that
Page 77 and 78: Create a Numeric Display 1 Click on
Page 79 and 80: 4 The “Safety” page shows the s
Page 81 and 82: Devices Introduction General Note T
Page 83 and 84: Inputs / Outputs configuration 1 To
Page 85 and 86: Altivar 312 Introduction Note The A
Page 87 and 88: Change settings for Preset Speeds 1
Page 89 and 90: Settings for the gear ration and PT
Page 91 and 92: Power cycle 1 In case of display
Page 93 and 94: Automation Components Hardware-Comp
Page 95 and 96:
Component Protection Classes Positi
Page 97 and 98:
Preventa Safety Module: XPSAC5121 M
Page 99 and 100:
Lexium 32 servo drive Voltage rang
Page 101:
Contact Publisher Process & Machine
show all

Compact / Hardwired / Logic Controller / M238 ... - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?