BRL0400 Instructions - Halfords
BRL0400 Instructions - Halfords
BRL0400 Instructions - Halfords
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Fitting <strong>Instructions</strong> for Ring Automotive<br />
Slimline Cruise-lite Ice Lamp (<strong>BRL0400</strong>)<br />
Carefully read the instructions prior to installation. Retain the instructions for future reference.<br />
UK REQUIREMENTS ONLY<br />
LEGAL REQUIREMENTS<br />
OTHER COUNTRIES CONSULT LOCAL REGULATIONS<br />
Obligatory front position lights<br />
These regulations only apply if the front position lights are not to be wired in or<br />
used in conjunction with the vehicle’s current front position lights (sidelights).<br />
When fitting a pair of front position lamps you should obey the following legal<br />
requirements:<br />
Obligatory front position lamps should be fitted at a maximum<br />
distance from the side of the vehicle of 400mm, with no minimum separation distance between each lamp. They should<br />
also be fitted at a maximum height above the ground of 1500mm or if the structure of the vehicle makes this<br />
impracticable, 2100mm. There is no minimum height requirement above the ground.<br />
Optional front position lights<br />
There are no legal requirements if the front position lights are to be wired into the vehicle’s current sidelight circuit and<br />
operated in conjunction with the sidelights.<br />
THE ROAD VEHICLES LIGHTING REGULATIONS 1989<br />
Equipment Required<br />
• Electrical and a cross headed screwdriver<br />
• Terminal crimp or pliers<br />
Other Parts Required<br />
• 2x earth rings<br />
• Dashboard mounting switch (required for obligatory wiring only)<br />
• Suitable length of cable<br />
• 2x “Scotchlok” connectors (required for optional wiring only)<br />
• Electrical connector block<br />
• In-line 5 Amp fuse (Optional)<br />
• Self-tapping screw<br />
Important<br />
Before commencing any of the fitting operations, ensure that the vehicle is parked safely off the road with the handbrake<br />
on and the correct fuse or fuses are removed to isolate the circuit.<br />
Read the instructions carefully before starting to fit the lamps, if in doubt consult a qualified auto electrician.<br />
Warning, disconnecting the battery may disable management systems, radio codes etc.<br />
Remove the protective plastic strip from the front of each lamp at the end of the installation before first switching on.<br />
Mounting the lamps<br />
The lamps can be fitted above or below the bumper.<br />
1. Check any chosen position carefully to ensure it does not foul any piping or wiring.<br />
2. The lamps must be fitted symmetrically.<br />
3. Using the self adhesive tape provided, mount the lamp in a suitable position.<br />
4. Ensure that the lamp is mounted rigidly and does not vibrate.<br />
Wiring Diagram<br />
Diagramme de câblage<br />
Schaltbild<br />
Schema di cablaggio<br />
Diagrama de cableado<br />
Ledningsføringsdiagram<br />
Obligatory Wiring<br />
(If the unit is not to be used in conjunction<br />
with the vehicle’s existing sidelights)<br />
1. Connect the red wire through to an<br />
ignition controlled 12v supply via a<br />
switch on the dashboard.<br />
2. It is always advisable to fit a separate<br />
in-line fuse holder. Fit this as close to<br />
the ignition feed as possible to<br />
minimise voltage drop. Clip the fuse<br />
into position to protect the circuit.<br />
3. Connect the plain black wire to a good<br />
earth on the chassis using an earth ring<br />
and a self-tapping screw. Ensure that<br />
there is a good metal to metal contact.<br />
4. Replace any fuses removed.<br />
Diagrama da Cablagem<br />
Kopplingsschema<br />
Bedradingsschema<br />
Schemat połączeń<br />
Schéma zapojení<br />
2<br />
1<br />
H<br />
D<br />
1<br />
2<br />
I<br />
Optional Wiring<br />
(If being used in conjunction with the<br />
vehicle’s existing sidelights)<br />
1. Connect the red wire to the vehicle<br />
sidelight circuit using a splice<br />
connector, (check your handbook for<br />
the appropriate wire colour).<br />
2. Connect the plain black wire to a good<br />
earth on the chassis using an earth<br />
ring and self tapping screw. Ensure that<br />
there is a good metal to metal contact.<br />
3. Replace any fuses removed.<br />
1<br />
1<br />
2 2<br />
Aftercare<br />
Wash lamps with a mild solution of soap and water to remove dirt etc. Do not use harsh or abrasive cleaners.