UP100 brochure:Layout 1.qxd - Prodrive
UP100 brochure:Layout 1.qxd - Prodrive
UP100 brochure:Layout 1.qxd - Prodrive
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
where inspiration and innovation combine<br />
MICROPROTEUS <strong>UP100</strong>
MicroProteus TM is a highly compact and rugged range of electronic control<br />
units, powered by an automotive specification Motorola MPC555 processor.<br />
The uP100 unit provides full rapid prototype capabilities through the use of<br />
MATLAB® generated autocode.<br />
uP100 is the smallest in the range and is ideal for use in a multitude of<br />
embedded real time applications that require a 32 bit floating point<br />
processor coupled with onboard I/O. e.g. Suspension and driveline control.<br />
DIGITAL SUBSYSTEMS<br />
• Motorola MPC555 “BlackOak” microcontroller at 40MHz<br />
• 512Kb external SRAM<br />
• 8Kb non-volatile RAM<br />
• Optional <strong>Prodrive</strong> internal datalogger with uP100<br />
-Log external and Simulink signals<br />
-Logs at any multiple of model iteration rate (e.g. 1ms)<br />
-Available with up to 1Gb memory<br />
• Software compatibility with <strong>Prodrive</strong> blockset, MATLAB® (Simulink®,<br />
Stateflow, Real-Time Workshop, Embedded Target for MPC555) and<br />
PIPPATM<br />
• DIAB and GNU complier support (GCC included with <strong>Prodrive</strong> software suite)<br />
ENVIRONMENTAL<br />
• Mechanical package: All aluminium, milled from solid case<br />
• Weight:<br />
370g<br />
• Dimensions:<br />
153mm x 72mm x 42mm<br />
• Storage temperature: -40° to +125°C<br />
• Operating temperature: -40° to +85°C (tested to 100°C)<br />
• Sealing:<br />
IP67<br />
• Drop<br />
Random drop on concrete from 1m<br />
• Vibration:<br />
Tested to 20g RMS for 2 hours<br />
uP100 has an optional internal datalogger, available in up to 1Gb memory<br />
size. The data logger is configured via Simulink®blocks (supplied as part of<br />
the <strong>Prodrive</strong> Software suite). The logging rate can be any multiple of the<br />
model iteration rate (typically 1ms)<br />
COMMUNICATION<br />
• 2 x CAN (2.0b) buses *<br />
• Supports CCP (CANape & INCA)<br />
• 2 x RS232 serial ports *<br />
• USB datalogger upload (where fitted)<br />
* only two of the four available communication interfaces can be used at any one time<br />
I/O SUBSYSTEM & POWER SUPPLY<br />
• 10 x single ended analogue inputs<br />
• 6 x digital inputs<br />
• 8 x 2-Amp low side drives, with built in diagnostic capability<br />
• 2 x 20mA analogue I-drives. (Can be configured as voltage output)<br />
• 2 axis accelerometers<br />
• 1 x rugged autosport connector (37 way), EMC Filtered<br />
• Wide supply range (7-36V), with reverse over voltage and temperature<br />
protection<br />
ADDITIONAL PRODUCT INFORMATION<br />
• Internal temperature sensor<br />
• Internal battery voltage sensor<br />
• Status / “Heartbeat” LED integrated into the case<br />
• Configurable* pull up / pull down resistors on both analogue and digital<br />
inputs<br />
• Configurable* thresholds on digital inputs<br />
• 2 x sensor power supplies<br />
* Please enquire about configuration options when ordering. Additional charge may apply<br />
Note: The following products are required<br />
MATLAB R13 or MATLAB R14 including:<br />
• Simulink®, Real Time Workshop®, Stateflow® (optional), Stateflow coder® (optional)<br />
• Complier:<br />
GNU (GCC included with <strong>Prodrive</strong> software suite) or Windriver DiabTM ‘C’ Compiler version<br />
4.3, 4.4, 5.0<br />
<strong>Prodrive</strong> reserves the right to amend product specification without prior notice. E @ O E<br />
• Any Simulink® variable or external input to the ECU can be logged<br />
• Data uploaded via USB, for viewing in PIPPA, CSV or MAT format<br />
PRODRIVE KENILWORTH WARWICKSHIRE CV8 1NR T. +44(0)1676 536002 F. +44(0)1676 536205 E. ELECTRONICS@PRODRIVE.COM<br />
WWW.PRODRIVE.COM/ELECTRONICS
Change language