Wet - Scruples

wet-on-wet
colour technique
• Blazing Highlights® gel colour can be applied on top of wet, processing High Definition® and Shadow LowlightsTM * gel
colour to achieve subtle, natural highlights
*only applies when using Shadow LowlightsTM as an all over colour
• Simultaneous colouring and highlighting saves time, increases revenue and directly impacts your residual business
• Blazing Highlights® and gel base haircolour mixtures combine during processing, creating a blended, monochromatic effect
• Service can only be provided by a professional haircolourist
Recommended Additional Scoops and Processing Times for Wet-on-Wet Colour Applications
Blazing Highlights®
Toner Infused • Gel Colour
High Definition®
Custom Mixing • Gel Colour
Shadow LowlightsTM
Filler Infused • Gel Colour
Natural/Tinted
Levels 1 – 6
Natural/Tinted
Levels 7 – 10
Processing Times
1 – 2 extra scoops 1 – 2 extra scoops
1 extra scoop 1 extra scoop
Room temperature
20 – 45 Minutes
Heat Not Recommended
Room temperature
20 – 45 Minutes
Heat Not Recommended
Note: If hair is previously tinted or has build-up from hard water do not add extra scoop; the suggested scoops for wet-on-wet already
account for this.

Directions:
1. Determine the client’s tinted haircolour level:
• Blazing Highlights® Toner Infused Gel Colour System
is formulated using Blazing Highlights® Level Finder
to determine the tinted haircolour level and ensure
predictable results
• Always formulate to the darkest level
2. Select the client’s desired highlight shade from the
Blazing Highlights® Demonstration Swatch Book or
from the top row of Blazing Highlights® Formulation
Chart. Highlights done using the wet-on-wet colour
application do not match the Blazing Highlights®
Swatch Book; these custom shades are a blend of the
base and highlight colours.
3. Select the client’s desired highlighting formula at the
top of the formulation chart. On the left side of the chart
locate the client’s tinted haircolour level. Intersect the
two columns to determine the highlighting formula.
4. Mixing: Measure the recommended scoops of Blazing
Highlights® X-tra Light Booster Concentrate from the
formulation chart for desired highlight shade. Add the
extra scoops needed from the chart on the front side
of this sheet. Measure the recommended amount of
Blazing Highlights® gel colour and Oil Lightener, pour
into the Booster Concentrate and dissolve. Measure the
recommended amount and volume of Pure Oxi® Clear
Developer. Gradually pour developer into the bowl and
whip to a gel-like consistency.
5. Application: Apply High Definition® or Shadow
LowlightsT M gel colour from scalp to ends. Weave
or slice Blazing Highlights® into hair, applying a
generous amount of product to the hair that is placed
in Scruples Color Papers or Foils.
6. Processing:
• Process at room temperature for 20 – 45 minutes
Note: When High Definition® or Shadow LowlightsT M
are applied directly on the scalp, processing with heat
is not recommended due to possible scalp irritation. If
High Definition® or Shadow LowlightsT M are not on
the scalp and are only on the length of hair or in color
papers or foils, processing with heat for 15 – 30 minutes
is an option. When processing with heat, a loose-fitting
processing cap should be used to prevent the base
colour from drying out.
7. Removal: Rinse hair and shampoo with Scruples Renewal®
Color Retention Shampoo. Rinse thoroughly and repeat.
Spray liberally with Scruples NO H2O2® No Peroxide to
condition, improve colour retention and remove residual
peroxide from the hair. Work thoroughly through hair and
rinse after 3 minutes. Condition with Scruples Renewal®
Color Retention Conditioner and rinse.
Note: If the hair is excessively porous or fine textured,
use your professional judgement and reduce the number
of total scoops accordingly.
Scruples Inc., Dist. • Minneapolis, MN 55044-9009 USA • 1.800.457.0016 • Technical Assistance: 1-888-SCRUPLES (727-8753)
scrupleshaircare.com • 72097-2 412 • Printed in USA