Timberlox Interior / Exterior Liquid Plastic ... - Cloverdale Paint

Product Description
TECHNICAL SPECIFICATIONS DATA SHEET
43324
Timberlox Interior / Exterior Liquid Plastic
Urethane High Gloss
Timberlox Interior / Exterior Liquid Plastic Urethane High Gloss is a reinforced alkyd urethane with a
transparent finish that protects wood surfaces. Provides a durable mar, stain and chip resistant finish. It is
ideally suited for use on furniture, paneling, trim, floors and over stained wood. This product contains an
Ultra-Violet Absorber and may be used on exterior surfaces. Approved by the Master Painter's Institute
under category # 29,# 56 & # 75.
Intended Uses
Ideally suited for furniture, paneling, trim, floors and over stained wood surfaces. Not recommended over
lacquer sanding sealer, shellac or stains containing stearates. Do not apply over asphalt, rubber or vinyl
flooring.
Product Data
Color:
Drying Time: (@20 o C 50% Relative Humidity)
Clear
Tack Free: 1 Hour
Finish: Re-Coat: 5 Hours
High Gloss (>90 units @ 60 o )
Thinner:
Bases: 78001 Mineral Spirits
N/A
Flash Point (Tag Closed Cup):
42 o C (107 o F)
Vehicle Type:
Urethane- Alkyd
Viscosity:
25" - 28" #4 Ford Cup
Solids by Volume:
40% V.O.C. (Before Thinning):
471 g/L or 3.9 lbs/gal
Solids by Weight:
48%
Recommended Film Thickness
(Per Coat):
Wet: 2.3 - 3.2 mils (58 - 81 microns)
Dry: 0.9 - 1.2 mils (23 - 30 microns)
Theoretical Coverage (Per Coat):
500 - 700 ft 2 /gal (12.0 - 15.0 m 2 /L)
43324 Page 1 of 2
60-0090

Surface Preparation
Surface must be clean, dry and free of dirt, grease, wax or previous floor coatings. Sand with fine
sandpaper and remove dust with tack cloth. A first coat of 43324 reduced 10% with 78001 Mineral Spirits
or 45114 Alkyd Sanding Sealer is recommended on bare woods.
Recommended Primer
Drywall
Wood
Masonry
- N/A
- Seal bare wood with 45114
Alkyd Sanding Sealer or thin the
first coat 10% with 78001 Mineral
Spirits
- N/A
Method
Thinning
Cleanup
- Brush, roller or airless spray.
Airless tips: 0.007" - 0.011"
- Thin first coat up to 10% with 78001
Mineral Spirits. Use as supplied for
additional coats
-78001 Mineral Spirits
Steel
- N/A
For detailed information please refer to MSDS
Check for recent amendments to this data sheet at www.cloverdalepaint.com/html/catalog_recent_ar.asp
Safety Precautions
Warning
CONTAINS PETROLEUM DISTILLATE. HARMFUL IF SWALLOWED. CAUSES EYE AND SKIN
IRRITATION. VAPOUR HARMFUL. COMBUSTIBLE. KEEP OUT OF REACH OF CHILDREN. Keep away
from heat, sparks, open flame. Do not take internally. Avoid contact with eyes and skin, and breathing of
vapour or spray mist. Wear an air supplied mask when applying in enclosed areas. Wash thoroughly after
handling. CLOSE CONTAINER AFTER EACH USE. USE WITH ADEQUATE VENTILATION.
First Aid
In case of eye contact, flush immediately with plenty of water for at least 15 minutes. Wash contaminated
skin with soap and water. If ingested, call physician or the Poison Control Centre immediately.
Warranty Disclaimer
Cloverdale Paint manufactures quality products. In the event that this product is defective or in any way
unsuitable for the application for which it is sold, Cloverdale Paint Inc. will replace the product free of
charge. The warranty provided by this data sheet is the only warranty or guarantee of quality made in
respect of this product by Cloverdale Paint Inc. By purchasing this product the customer accepts this
warranty in lieu of all others, and waives all claims to any other remedy arising from any warranty or
guarantee of quality, whether such warranty or guarantee of quality was made expressly to the customer or
implied by any applicable law.
6950 King George Hwy., Surrey, BC, V3W 4Z1
Web Site: www.cloverdalepaint.com Email: helpdesk@cloverdalepaint.com
Phone: (604) 596-6261 Fax: (604) 597-2677
60-0090v2 6/5/06
43324 Page 2 of 2
60-0090