ProCoat Latex Drywall Primer - Cloverdale Paint

COMPLIANCE INDICATORS
At October 27, 2011
ProCoat Latex Drywall Primer
05720
Environment Canada VOC
LEED
✔
✔
TECHNICAL CHARACTERISTICS
Colours
VOC (g/L)*
White (05720) < 100
*Before tinting
Finish
Flat
DESCRIPTION
ProCoat Latex Drywall Primer is a professional interior drywall
primer/undercoat for use on new drywall, interior masonry
surfaces, and to prime patching compounds used with wall repairs
prior to repainting. Best suited for use under latex and acrylic
finish coats. Formulated to provide a combination of good hiding
and sanding characteristics at a value price.
RECOMMENDED USES
• For use on new drywall, interior masonry surfaces, and
to prime patching compounds used with wall repairs prior
to repainting. May be used under latex and oil base finish
coats.
FEATURES
• Good hiding and sanding characteristics
• For use under latex and oil base finishesEvens out prosity fro
a topcoat finish free of flashing
• Good balance of price and performance
Solids & Density
Volume: 31%
Weight: 52%
Density: 11.86 lbs per gallon (container extra)
Film Thickness (Per Coat)
Wet: 4.5 - 6.5 mils (120 - 163 microns)
Dry: 1.5 - 2.0 mils (38 - 50 microns)
Coverage (Per Coat):
250 - 330 ft² / gallon (6.1 - 8.0 m²/L)
Viscosity
90 - 95 KU #4 Ford Cup
Application Equipment
Brush: Use a polyester brush
Roller: Use a 3/8” - 3/4” nap synthetic cover
H.V.L.P Spray: 10 psi cap pressure 1.3 tip size
Airless Spray: Pressure 2000 psi, Tip .013” - .015”
Drying Time at 20°C 50% Relative Humidity
Tack Free: 30 minutes
Re-Coat: 3 hours minimum
Thinner
Not normally recommended. 10% clean water for spray
applications.
Clean Up
Warm, soapy water
Storage Temperature
4°C (40°F) - 32°C (90°F)
Keep from freezing
Flash Point
N/A
Shelf Life
2 year maximum - unopened
Cloverdale Paint Inc. 6950 King George Blvd. Surrey, BC V3W 4Z1 Canada Tel: 604.596.6261 Fax: 604.596.6261
Formulated and Manufactured
in Surrey, British Columbia
www.cloverdalepaint.com
Page 1 of 2
Version: 10/27/2011

ProCoat Latex Drywall Primer
05720
Formulated and Manufactured
in Surrey, British Columbia
SURFACE PREPARATION
All Surfaces
All surfaces must be clean, dry, free of powdery materials
and loose or scaling paint. Drywall joints must be thoroughly
dry and free from sanding dust. A lower porosity "topping mix"
is recommended as the final drywall compound coat for more
uniform sheen. Sand lightly on the board areas to avoid nap
raising. Use only at temperatures above 10°C (50°F).
WARNING! If you scrape, sand or remove old lead paint from any
surface you may release lead dust. LEAD IS TOXIC. EXPOSURE
TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved
respirator to control lead exposure. Carefully clean up with a
wet mop or HEPAvacuum. For additional information, Canadian
customers contact the Product Safety division of Health Canada
at 1-800-O-CANADA, US customers contact the U.S. EPA/Lead
Information Hotline at 1-800-424-LEAD (5323).
RECOMMENDED TOPCOATS
Pre-Painted Surfaces
De-gloss by sanding and must be soundly adhering prior to
repainting.
Wood
N/A
Masonry
Conventional solvent or waterbased architectural paints
Drywall
Conventional solvent or waterbased architectural paints
Steel
N/A
SAFETY PRECAUTIONS
For detailed information please refer to MSDS
Warning
Keep from freezing. USE WITH ADEQUATE VENTILATION. Close
container after EACH use. Keep out of reach of children.
Do not take internally.
First Aid
In case of eye contact, flush immediately with plenty of water
for at least 15 minutes. Wash contaminated skin with soap and
water. If ingested, call physician or the Poison Control Centre
immediately.
RECENT AMENDMENTS
Check for recent amendments to this data sheet at
www.cloverdalepaint.com
LIMITATION OF LIABILITY
To the best of our knowledge, the technical data contained
herein ar true and accurate at the time of issueance but are
subject to change without prior notice. We guarantee our product
to conform to the specifications contained herein.
WARRANTY DISCLAIMER
Cloverdale Paint manufactures quality products. In the event
that this product is defective or in any way unsuitable for the
application for which it is sold, Cloverdale Paint Inc. will replace
the product free of charge. The warranty provided by this data
sheet is the only warranty or guarantee of quality made in
respect of this product by Cloverdale Paint Inc. By purchasing
this product the customer accepts this warranty in lieu of all
others, and waives all claims to any other remedy arising from
any warranty or guarantee of quality, whether such warranty or
guarantee of quality was made expressly to the customer or
implied by any applicable law.
Read Label and Material Safety Data Sheet Prior to Use. Catalogue: 10-0080
Cloverdale Paint Inc. 6950 King George Blvd. Surrey, BC V3W 4Z1 Canada Tel: 604.596.6261 Fax: 604.596.6261 www.cloverdalepaint.com
Page 2 of 2
Revision Date: October 27, 2011