G 2600 VC G 2600 VC Plus

More documents

Recommendations

Info

CAUTION Remove the spark plug cable to prevent accidental ignition of the engine before making any repair. TROUBLESHOOTING Symptom POSSIBLE CAUSE SOLUTION Engine will not start No gasoline Fill gas tank Choke is not in the correct position. Slide choke lever out to closed position. Water pressure built up in the machine. Squeeze the trigger to release the pressure. For additional engine problems refer to the engine manual. Unit does not reach high pressure. Output pressure varies high and low. No detergent. Garden hose connection leaks. Diameter of garden hose is too small. Water supply is restricted. Not enough inlet water supply. Water inlet filter is clogged. Black detergent nozzle is attached. Not enough inlet water supply. Pump is sucking air. Water inlet filter is clogged. Spray nozzle is obstructed. Calcified gun, hose or spray wand. Detergent suction tube not properly connected to the machine. Detergent is too thick. Filter on detergent suction tube is clogged. Damaged or clogged detergent suction tube. A high pressure nozzle is attached. Metering valve closed. Spray nozzle is obstructed. Loose fittings. Missing/worn rubber washer. Replace with a 5/8 inch or larger garden hose. Check garden hose for kinks, leaks and blockage. Turn water on full force. Check garden hose for kinks, leaks or blockage. Remove filter and rinse out in warm water. Remove black detergent nozzle and attach high pressure nozzle Turn water on full force. Check garden hose for kinks, leaks or blockage. Check that hoses and fittings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle. Remove filter and rinse out in warm water. Blow out or remove debris with a fine needle. Run distilled vinegar through detergent suction tube. Check connection. Dilute detergent, for best results use Kärcher® detergent. Run warm water through filter to remove debris. Remove obstruction or replace detergent suction tube. Replace with black detergent nozzle. Open metering valve. Blow out or remove debris with fine needle. Check and replace if necessary. Insert new washer. Spray wand leaks. Spray wand not properly attached. Turn the swivel nut of the gun clockwise until connection is tight. Broken o-ring or plastic insert. Call Customer Support 14 English
Symptom POSSIBLE CAUSE SOLUTION Pump is noisy. Pump is sucking air. Check that hoses and fittings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle. Water leaks from pump (up to 10 drops per minute is permissible). Loose fittings. Water seals are damaged or worn. Thermal protection device is activated. Tighten fittings. Call Customer Support Thermal protection device will auto reset. Do not run pump for more than 5 minutes without spraying. Oil Drip. Oil seals are damaged or worn. Call Customer Support If you encounter any additional difficulties not listed, please call for help or visit our website. USA / Canada: 1-800-537-4129 www.karcher-help.com Mexico: 01-800-024-13-13 www.karcher.com.mx English 15
Page 1 and 2: G 2600 VC G 2600 VC Plus English 2
Page 3 and 4: MODEL OVERVIEW 4 2 3 12 1 9 5 6 13
Page 5 and 6: WATER SUPPLY (Cold Water Only) CAUT
Page 7 and 8: Assembling STEP 1: Insert joints (A
Page 9 and 10: CAUTION Engine shipped without oil.
Page 11 and 12: Detergents CAUTION This unit has be
Page 13: Cement Patios, Brick and Stone (wit

G 2600 VC G 2600 VC Plus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?