LED Modules - BAG electronics

More documents

Recommendations

Info

Technical annex Electronic control units Compare 1–10 V Interface /DALI Wiring Adressibility of ECG Number ECG Dimming Dimming profile 1-10 V DALI Two-core control line watch the polarity No Depends on installed dimmer resp. control unit Separate functions Tab. 2 Two-core control line, protected against rev. polarity Push-Dim – dimming and switching via push button ching and dimming is via a conventional push button. The DALI dimmable electronic control units from BAG electronics with Push-Dim function can be alternatively wired for this purpose. Here the phase or neutral conductor for example is bridged with either of the two DALI connection terminals. The push button can now be connected between the other mains conductor and the second DALI connection terminal. Simultaneous use of the DALI interface and a push button is not permissible. Yes Depends on installed dimmer resp. control unit Combined functions Standardised logarithmic Standards IEC 60929 IEC 62386 Service life of electronic control gears The service life and thus reliability of electronic control gear is determined by the failure rates of the components used. In addition to the electrical specification and quality of components, tronics ECGs from the ZITARES series are designed so that a failure rate of maximum 2% per 1,000 hours is expected with the maximum permissible housing temperature tc,max. This corresponds to a service life of 50,000 hours at a possible percentage of failed devices vice life of more than 20 years is achieved, whereby during this time period 10% of devices can statistically fail. With lower device temperatures the service life of the electronic control gear is increased. failure rate is approximately halved, corresponding to a service life of 100,000 hours. Exceeding the temperature tc,max can lead to a correspondingly drastic shortening of service life. To ensure the specified service life, all components and switching groups of BAG electronics ECGs are designed to operate below their permissible limit values. And in order to eliminate premature failures resulting from concealed defects, all devices pass through various test benches during the manufacturing process where component testing and measurements of operation-relevant data for example are implemented. The ECGs are then subjected to a final burn-in test before dispatch. Push button operation LED module OFF (Stand-by-mode) Tab. 3 LED module ON (Lamp operation mode) Short press of button Long press of button > 0.5 s LED module on LED module ON and dimming LED module Off Dimming up resp. down Long press of button — Synchronisization mode LED module = 100 % luminous flux 60
Technical annex LED and LED modules: Light and Colour Colour temperature: knowledge and facts CCT - Correlated Colour Temperature The complete diversity of visible light can be shown in the CIE standard colour chart as a simplified form of display. Individual colours are shown on the spectral colour line running along the outer border. White light as a mixed colour is shown along the black body curve. This curve has its origin in the red colour tone and specifies the colour sequence shown by a black body with increasing heat. The temperature of the black body is designated as light colour and pro- K cool white to 10,000 K daylight white. The temperature assigned to the light colour is termed Correlated Colour Temperature and normally abbreviated to CCT. Achievement of identical colour perception SDCM - Standard Deviation of Colour Matching The ANSI standard was introduced in order to more precisely specify colour tone tolerances of white light that segment the range along turers have defined their own significantly tighter classes, termed binning. CIE colour space C y 0,43 0,38 CIE chromatic diagram 520 0,33 510 500 490 480 470 460 540 560 580 3’000 2’000 4’000 6’000 10’000 380 600 [°K] 620 700 [nm] 0,28 0,27 0,32 0,37 0,42 0,47 0,46 Planck 2700 K 3000 K CIE colour space Cy 3500 K 4000 K 4500 K 5000 K 5700 K 6500 K These are intended to ensure that practically no colour deviations between the LEDs of a binning class can be noticed. A measure of the whereas with a 6-level ellipse significant colour differences are to be short. C x 0,44 0,42 0,40 3000 K 2700 K 0,38 4000 K 0,36 0,34 0,32 Cx 0,35 0,40 0,45 0,50 MacAdam Ellipses (1, 2, 3 and 4 steps) ANSI Standard Industry Standard Colour Bins 61
Page 1:
LED Products 2013 Electronic contro
Page 4 and 5:
Technical Roadma Partnership 4
Page 6 and 7:
Design concepts BAG LED portfolio O
Page 8 and 9:
Electronic control gear units ZITAR
Page 10 and 11: LED modules ASTARES ASTARES - LED m
Page 12 and 13: Productfinder - Selection table ECG
Page 14 and 15: Productfinder - Selection table Ele
Page 17 and 18: Electronic control gear units for L
Page 19 and 20: ECG Model and operating data Order
Page 23 and 24: + + ECG Model and operating data O
Page 31 and 32: + + + + + + + + + + ECG Model and o
Page 33 and 34: + + + + + + + + + + ECG Model and o
Page 39: ECG Model and operating data Order
Page 42 and 43: ASTARES linear LED modules in linea
Page 44 and 45: ASTARES plane LED modules in planar
Page 46 and 47: ASTARES square Compact square LED m
Page 48 and 49: ASTARES spot Compact LED modules in
Page 51 and 52: Light Engine NEXARES and CRONIUS Li
Page 53 and 54: Model and operating data Order Num
Page 59: LED dimming The use of dimmable ele
Page 63 and 64: Technical data subject to alteratio
show all

LED Modules - BAG electronics

Create successful ePaper yourself

Delete template?

Save as template?