part 1: section 2.2 - RedBookLive

LOSS PREVENTION CERTIFICATION BOARD 

RED BOOK 2011 

Volume 2 

LIST OF APPROVED 

PRODUCTS AND SERVICES 

- PASSIVE FIRE PROTECTION PRODUCTS & SERVICES 

- SECURITY PROTECTION SYSTEMS 

- RELATED INSTALLERS 

THIS VOLUME ALSO INCLUDES: 

- MANAGEMENT SYSTEMS 

- CONSTRUCTION PRODUCTS 

A Specifier’s Guide

PASSIVE PRODUCTS & SERVICES, SECURITY, MANAGEMENT 

SYSTEMS AND ENVIRONMENTAL 

Foreword by Peter Holland CBE OStJ QFSM, President of the Chief Fire Officers Association 

and Chief Fire Officer of Lancashire Fire and Rescue Service 

Dear Specifier 

Continuing economic uncertainty makes us all aware of the need for protection against unexpected risks. 

In the life of any building, infrastructure or industrial facility, designers must increasingly consider business 

risk, especially potential exposure to the ‘unexpected’ such as fire or attack on security and security systems 

failure. By considering carefully what they specify, designers can mitigate these risks and demonstrate due 

diligence and engineering assurance whilst helping to prevent business losses. 

Business losses, whether caused by fire or security failure, can be large and disruptive; either is bad for 

publicity. And, although it is impossible to foresee all eventualities, by specifying effective, properly installed 

fire and security protection systems, the negative consequences of an incident can be reduced considerably. 

One of the best ways of doing this is to select products, systems and installers that are approved and listed by 

an independent third party certification body such as LPCB. Third party approval is confirmation that these 

products, systems and their installers have met and continue to meet appropriate standards. Independent 

third party certification is the best and most trustworthy form of approval. 

As an independent certifier, LPCB has one of the most extensive fire and security testing laboratories in the 

world and its approvals are undertaken by a highly qualified team of expert scientists and engineers. LPCB 

develops standards with rigorous consultation and involvement of a wide range of stakeholders, including 

clients, insurers, manufacturers, public bodies and the emergency services. This all goes to make the LPCB 

certification mark a mark you can trust 

I have, therefore, no hesitation in recommending the products and services listed in the Red Book 2011 to 

you. 

ii 20 Nov 2011



Introduction 

Welcome to the 2011 Edition of the “Red Book”, the LPCB List of Approved Fire & Security Products and 

Services. The Loss Prevention Certification Board (LPCB) is part of BRE Global and together with the listings, 

the LPCB mark signifies that products and services have been approved by LPCB. The Red Book is an 

essential reference for specifiers, regulators, designers and end users of these products and services - if it is 

listed here, you know it has been checked out by people you can trust. 

BRE Global is part of the BRE Group under the BRE Trust. It is an independent third party approvals body 

offering certification of fire, security and sustainability products and services to an international market. 

BRE Global - protecting people, property and the planet. 

The Red Book is divided into sections which list related groups of products and services such as suppression, 

security and so on. Each section also summarises the technical basis for the approval of each product or 

service. The Red Book should always be used in conjunction with rules, regulations and design specifications 

required by the relevant Authority. 

The 2011 edition of the Red Book comprises 2 Volumes: 

Volume 1: 

Volume 2: 

Fire Detection and Alarm products & services 

Fire Suppression products & services 

Related Installers 

Passive fire protection products & services 

Security Protection systems 

Related Installers 

Management Systems 

Construction products 

Listings are given in the name of the manufacturer or service provider, in alphabetical order. 

The Red Book is available free of charge in hard copy, CD and memory stick. It is also available on our 

website at www.redbooklive.com . The website gives you the most up to date 

information on which products are approved and in the unlikely event of suppliers needing to recall products 

or services or suspend production will identify these. 

Red Book updates 

Product and services approval details are amended regularly. To ensure that you are using the most up to 

date information please refer to www.RedBookLive.com . 

What is Third Party Approval? 

Third party approval (or certification) is a conformity assessment process, carried out by a body that is 

independent of both supplier and customer organisations. It provides confirmation that products and services 

have met and will continue to meet the requirements of specified standards and other normative documents. 

Third party approval provides a safeguard as to the performance of a product or service. 

LPCB third party product approval schemes are quality assurance schemes and comprise initial type testing 

and technical evaluation, assessment and surveillance of the manufacturer’s quality system and production 

procedures, regular audit testing, labelling and listing. 

Similarly, LPCB schemes for suppliers of services (installers) are also quality assurance schemes comprising 

a technical assessment of a contractor’s capability, assessment and surveillance of the installer’s quality 

system and production procedures, regular inspection of completed installations and listing. 

20 Nov 2011 iii



Benefits of Third Party Approval 

A frequent concern of stakeholders is in knowing whether a product will perform in accordance with the stated 

specifications. These concerns can involve such product attributes as safety, health or environmental impacts, 

durability, compatibility, suitability for intended purposes or for stated conditions, and other similar 

considerations. These issues can all be addressed through product approvals. 

For specifiers, regulators, insurers, manufacturers and installers, the benefits of an LPCB approval are: 

For specifiers and regulators: 

 

 

 

Risk reduction - specifying LPCB approved products and services demonstrates due-diligence and best 

endeavour and mitigates against possible accusations of negligence. 

Avoidance of costly mistakes - you can trust LPCB approved products and services to conform each 

and every time. 

Time - using Red Book Live to search for and assess products and services can save you time. 

For manufacturers and installers: 

 

 

 

Increased global sales - LPCB approval is recognised and specified widely throughout the world. In 

some territories LPCB approval is a mandatory requirement. 

Added value of the product or service - LPCB approved products and services are recognised as 

providing added value given their ability to conform each and every time. 

Reduced liability - LPCB approved products and services demonstrate due-diligence which can reduce 

liability for both you and your customers. 

The LPCB Mark is a Mark you can Trust. 

The Third Party Approval Process 

LPCB offers approvals to existing British, European, International and LPCB’s own Loss Prevention 

Standards (LPSs). LPCB’s LPS approval schemes for both products and services are essentially level 5 

schemes, as described in ISO/IEC Guide 67, with the added requirement to have a quality system certificated 

to ISO 9001. 

The technical requirements of LPCB schemes are given in Loss Prevention Standards (LPSs). These 

documents are drafted by LPCB technical experts in conjunction with appropriate external experts. 

They are then peer reviewed by representatives from trade bodies, regulators, insurers, specifiers, 

manufacturers and other suppliers. 

Finally these documents are approved for use by the BRE Global Governing Body; the Body that oversees all 

of the certification activities of BRE Global including LPCB. 

On occasion, approval may be carried out to other international standards where this is appropriate to a 

particular territory. 

Product schemes comprise: 

 

 

 

Initial type testing and evaluation of product, sampled by LPCB 

Approval and surveillance of the manufacturer’s (or supplier’s) quality management system to ISO 9001 (if 

you have products in for testing at LPCB, it generally costs little or no more to achieve ISO 9001 

certification). 

Assessment and surveillance of the manufacturer’s (or supplier’s) factory production control system (FPC) 

iv 20 Nov 2011



 

 

 

Periodic audit testing of the product from either the factory or marketplace 

Labelling or marking as appropriate. 

Listing of the approved product (service) in the Red Book. 

Installer schemes comprise: 

 

Technical assessment of the installation contractor’s capability 

Approval and surveillance of the contractor’s quality management system to ISO 

9001 or assessment against the requirements of the relevant Loss Prevention Standard where ISO 9001 

is not appropriate. (If you have applied for LPCB assessment of your services, it generally costs little or no 

more to achieve ISO 9001 certification). 

 

 

 

Regular surveillance inspections of on-going installations 

The issue of Certificates of Conformity to demonstrate compliance for each installation 

Listing of the approved installer in the Red Book. 

The LPCB Mark 

After approval of a product or service the manufacturer or service provider is allowed to place the LPCB 

certification mark, as shown below*, on the product, packaging and literature etc. 

Where LPCB holds accreditation through the United Kingdom Accreditation Service (UKAS), the approved 

company is allowed to include the UKAS logo alongside the LPCB mark for certain applications e.g. 

promotional literature or material and stationery, as shown below.* 

The LPCB scheme rules define how and where the marks can be used. 

The LPCB horseshoe is the mark you can trust and it is recognised in 45 countries around the world by 

regulators, specifiers, designers and end users. 

20 Nov 2011 v



Full details of LPCB accreditation can be found on the UKAS website at www.ukas.com 

. 

The products listed in Part 5 - Construction Products are approved under our BRE Certification brand:- 

Where management systems certification under a BRE Global accredited scheme is granted, the approved 

company is allowed to use the following mark on promotional literature or material and stationery 

All schemes are based on product testing/assessment and regular auditing. 

European Directives 

For products to be placed on the European market, manufacturers must comply with the regulatory 

requirements of a number of European Directives. 

To demonstrate compliance with these Directives, a manufacturer must make a declaration, based on an 

evaluation of the product, and affix the relevant mark. 

For some products the manufacturer will need to use the services of a Notified Certification Body or Notified 

Test Laboratory to demonstrate that the evaluation of the product has been carried out in whole or in part by a 

body independent of the manufacturer. Other products can merely be marked on the basis of a self 

declaration of conformity by the manufacturer. 

The relevant mark shows that a product meets minimum regulatory standards of health and safety as laid 

down in the Directives. It is not a quality mark and does not necessarily relate to the functional performance of 

the product. 

BRE Global is a Notified Body for: 

The Construction Products Directive (CPD) 

Pressure Equipment Directive (PED) 

Marine Equipment Directive (MED) 

Transportable Pressure Equipment Directive (TPED) 

vi 20 Nov 2011



Where the services of a Notified Body is required in order for a manufacturer to affix a mark to a product, BRE 

Global can provide a comprehensive service. 

Other Approvals 

BRE Global carries out approvals of a number of other construction products and management systems under 

other approval brand names. 

The details of these schemes are given in the relevant introductory sections. 

For Fire and Security Products and Services Trust the LPCB Mark 

20 Nov 2011 vii

CONTENTS 

1 Building products 1 

SECTION 1 Approved installers of passive fire protection products 3 

SECTION 1.1 LPS 1500 approved installer of fire resisting compartmentation system 4 

SECTION 1.2 LPS 1531 approved installer of passive fire protection products 5 

SECTION 2 Construction product systems (building envelope, roofing & partitions) 13 

SECTION 2.1 LPS 1181 Series 14 

SECTION 2.1.1 LPS 1181 lining materials 16 

SECTION 2.1.2 LPS 1181-1 cladding products used for the external envelope of 

buildings 17 

SECTION 2.1.3 LPS 1181-2 sandwich panels or built-up panel systems used internally in 

a building 36 

SECTION 2.1.4 LPS 1181-3 (draft) cladding used in pod construction 41 

SECTION 2.2 LPS 1208 composite construction elements 43 

SECTION 2.3 LPS 1581 external cladding systems on a masonry substrate 65 

SECTION 2.3.1 LPS 1581 external thermal insulated cladding (ETICS) on masonry 

substrates 66 

SECTION 2.3.2 LPS 1581 rain screen cladding systems (RSC) on masonry substrates 69 

SECTION 2.4 LPS 1582 external cladding systems supported by a structural steelwork 

frame 71 

SECTION 2.4.1 LPS 1582 external thermal insulated cladding (ETICS) supported by a 

structural steel frame 72 

SECTION 2.4.2 LPS 1582 rain screen cladding system (RSC) supported by a structural 

steel frame 75 

SECTION 2.5 Roofing products 76 

SECTION 2.5.1 Protection against fire from outside the building 77 

SECTION 2.5.2 Protection against fire from inside the building 84 

SECTION 2.6 Reaction to Fire (RTF) classifications for Materials and Products 85 

SECTION 3 LPS 1132 wall & floor penetration and linear gap seals 86 

SECTION 4 Structural steel fire protection 131 

SECTION 4.1 LPS 1107 structural steel fire protection - board and cementitious 

coverings 132 

SECTION 4.2 Structural steel fire protection - intumescent thin film coatings 155 

SECTION 5 Protective covering materials & scaffold cladding 160 

SECTION 5.1 LPS 1207 Protective covering materials 161 

SECTION 5.1.1 LPS 1207 protective covering materials - sheeting 162 

SECTION 5.1.2 LPS 1207 protective covering materials - pre-formed 172 

SECTION 5.2 LPS 1215 scaffold cladding materials 173 

SECTION 6 Cavity fire barriers 177 

SECTION 7 LPS 1195 temporary buildings for use on construction sites 179 

SECTION 8 Products assessed for use in surface and sub surface transport applications 

180 

SECTION 9 Fire Protected Timber Stairs 186 

2 Fire doors and shutters (incorporating installer scheme for fire and security doors) 

191 

SECTION 1.1 Firebreak doors and shutters 193 

SECTION 1.2 Lift landing doors 205 

SECTION 2 Fire and security door installers 206 

SECTION 3 Service and maintenance of doors 208 

3 Smoke and fire ventilation systems 213 

SECTION 1 Fire dampers 215 

viii 20 Nov 2011

CONTENTS 

SECTION 2 Fire resistant ducts 230 

SECTION 3 Smoke curtains 238 

SECTION 4 Powered smoke and heat exhaust ventilation 239 

SECTION 5 Grease Filters used in Commercial Kitchen Extract Systems 244 

4 Security protection products 245 

SECTION 1.1 Intruder detection equipment 247 

SECTION 1.2 Alarm transmission equipment and signalling systems 248 

SECTION 1.2.1 Alarm transmission equipment and systems 249 

SECTION 2 Safes, strongrooms and secure safe cabinets 252 

SECTION 2.1 Safes 253 

SECTION 2.2 Secure safe cabinets 260 

SECTION 2.3 Automatic teller machine (ATM) safes 263 

SECTION 2.4 Anti-bandit atm security devices 264 

SECTION 2.5 Deposit safes 265 

SECTION 2.6 Strongrooms 266 

SECTION 3 Secure office furniture 267 

SECTION 4 Secure enclosures 268 

SECTION 5 Physical security protection of buildings 287 

SECTION 5.1 High security doorsets 290 

SECTION 5.1.1 High security hinged doorsets with plain leaves 291 

SECTION 5.1.2 High security hinged doorsets with glazed leaves 412 

SECTION 5.1.3 High security hinged doorsets with other leaf designs 418 

SECTION 5.1.4 High security folding doorsets 420 

SECTION 5.2.1 Domestic doorsets approved to PAS 23-1 421 

SECTION 5.2.2 Domestic doorsets approved to PAS 24-1 423 

SECTION 5.3 High security windows 425 

SECTION 5.3.1 High security windows - external windows 426 

SECTION 5.3.2 High security windows - secondary glazing systems 427 

SECTION 5.3.3 Rooflights 430 

SECTION 5.4 Domestic security windows 431 

SECTION 5.5 Security grilles, blinds and barsets 434 

SECTION 5.6 Security shutters 444 

SECTION 5.7 Perforated security screens 449 

SECTION 5.8 Louvre vents 450 

SECTION 5.9 Garage doors 452 

SECTION 6 Access covers and hatches 454 

SECTION 7 Secure walling systems 460 

SECTION 8 Secure roofing systems 471 

SECTION 9 Perimeter security products 473 

SECTION 9.1 Security fencing 475 

SECTION 9.2 Security gates 490 

SECTION 9.3 Turnstiles 492 

SECTION 10 Vehicle security barrier 493 

SECTION 11 Gas cylinder security devices 494 

SECTION 12 Physical security devices for computers and other ict equipment 497 

SECTION 13 Database management for asset marking 501 

SECTION 14 Asset marking systems 503 

SECTION 15 'Theft resistant' electronic products 506 

SECTION 16 Letter plates and letter boxes (mail boxes) 508 

SECTION 17 Key safes 510 

20 Nov 2011 ix

CONTENTS 

SECTION 18 Security glazing 511 

5 Construction products 513 

SECTION 1 Anchors, connectors, fasteners and fixing systems 515 

SECTION 2 Drainage and plumbing systems 516 

SECTION 3 Flooring systems 517 

SECTION 4 Groundworks and foundation systems 519 

SECTION 5 Membranes 520 

SECTION 6 Pre-fabricated building systems 522 

SECTION 7 Building systems for dwellings 525 

SECTION 8 Trussed rafters (timber) 528 

SECTION 9 Thermal insulation systems 529 

SECTION 10 Wall and roof cladding systems 531 

SECTION 11 Walling, roofing and partition systems 534 

SECTION 12 Conservation of fuel and power 536 

6 Management system certification 537 

SECTION 1 Quality systems 539 

SECTION 2 Environmental systems 625 

SECTION 3 Health & safety certification BS OHSAS 18001 629 

x 20 Nov 2011

INDEX 

2 

2M KABLO SAN. ve TIC. A.S. 539 

A 

A & F Sprinklers Limited 539 

A M Profiles Limited 540 

A Steadman & Son 17, 540 

A.C. Plastic Industries Limited 540 

A.M. Fire Systems Limited 540 

Abbey Thermal Insulation Ltd 5 

Abbot Fire Group Limited 540 

AccentHansen 291, 541 

Actionair 215, 541 

AD Sprinkler Protection Limited 541 

Advanced Air (UK) Limited 223 

Advanced Electronics Limited 541 

AEI Cables Limited 541 

Alliance Valves and Piping Supplies Limited 

'AVPS' 542 

Alpine Fire Engineers Limited 542 

Aluroll Limited 444, 452, 542 

AMPAC Europe Limited 542 

Ampac Security Products Limited 542 

Andreu Barbera S.L. 193, 543 

Ansul Incorporated 543 

Anvil International Inc. 543 

Apollo (Beijing) Fire Products Co Ltd 543 

Apollo Fire Detectors Limited 544, 625 

APW Fire Protection Limited 544 

Aquacast (Fabrications) Limited 454 

Arabian Thermal Aire Industries Company Ltd 224 

ArcelorMittal Construction Belgium 43, 544 

ArcelorMittal Construction Belgium NV 17, 544 

Argus Fire Protection Company Limited 544, 629 

Argus-Spectrum Co 545 

Armstrong Priestley Limited 545 

Ascot Doors Limited 194, 208, 294, 445, 545 

Asgard Secure Steel Storage (a trading division of 

Flexiform Business Furniture Limited) 268 

Ashvale Fire Services Limited 545 

ASLR Fabrication Services Limited 545 

ATOM KABLO SANAYI VE TICARET A.S. 546 

Attenborough Doors Limited 194, 546 

Automatic Fire Control Limited 546 

Avert Fire (UK) Ltd 5 

B 

Bahra Cables Company 546 

Bailey & Mackey Limited 546 

Bainbridge International Limited 162 

Balmoral Sectional Tanks Limited 547 

Bangkok Cable Co Limited 547 

Bastion Security Installations Limited 269 

BBC Fire Protection Limited 547 

Beijing Siemens Cerberus Electronics Limited 547 

Besseges Limited 547 

Biamp Systems Corporation 548 

Blue Shield Fire Protection Limited 548 

Blyweert Beaufort Aluminium Limited 412 

Bolton Gate Co. Limited 420, 548 

Bond Engineering (Maintenance) Ltd 208 

Booth Industries Limited 548 

BPI Visqueen - Greenock 162, 548 

Bradbury Security 301, 412, 434, 498, 549 

Braithwaite Engineers Limited 549 

Brammall Inc. 549 

Britannia Kitchen Ventilation Limited 549 

British Gypsum 132 

Britton Merlin Limited 162 

Brucha Ges.m.b.H 18, 36 

Bryen & Langley Limited 5 

BSB Engineering Services Limited 224, 549 

BT Redcare 249 

Burton Safes Limited 550 

Bush (Fire Engineering) Limited 550 

C 

C W Fields and Son Limited 321, 413 

CA Group Limited 18, 550 

Cavicel SpA 550 

Ceodeux - Firetec 550 

Chaoyi Industry Development 551 

Charter Sepcialist Security Limited 551 

Checkmate Fire Solutions Ltd 6 

Chemring Energetics Limited 551 

Chubb Fire & Security Limited 551 

Circum Limited 552 

Clark Door Limited 194, 206, 552 

CLD Fencing Systems 475, 490, 552 

Clearway Environmental Services (UK) Limited 

323, 552 

Cleshar Contract Services Ltd 6 

Clymac Limited 552 

Compco Fire Systems Limited 553 

Computionics Limited (Trading as C-Tec) 553 

Control Equipment Limited 553 

Cooper Fulleon Limited 553 

Cooper Lighting and Safety Limited 554 

Cordek Limited 519 

Core Industrial Plastics Limited 163, 554 

Corecut Fire Protection (a division of Corecut 

Limited) 6 

Corus Panels and Profiles 19, 554 

Cranford Controls Limited 554 

Crawford UK Limited 208, 209, 554 

CTM Fire and Security Limited (Leyland & London 

Offices) 555 

Culimeta-Saveguard Limited 177, 555 

CVD Fire Protection Ltd 6 

D 

D.I.S. Sprinklers 555 

Daemon Fire and Security Limited 556 

Dalen Limited 498, 556 

Datatag ID Limited 501, 556 

Dätwyler Cables 556 

David Tyrrell T/A Nene Valley Acoustics 7 

Day-Impex Limited 556 

Debro Engineering and Presswork trading as 

Unistrut Ltd 557 

Defensor Group Limited 557 

Delta Extinctors S. A. 557 

20 Nov 2011 xi

INDEX 

Design & Supply Limited 324, 413, 557 

Dewey Waters Limited 557 

Digital Lighting (Dongguan) Co Ltd 558 

Don & Low Ltd, Nonwovens 163 

Doncaster Cables 558 

Dong-A Flexible Metal Tubes Co. Ltd. 558 

DoorTechnik 558 

Draka UK Limited 558 

Dryvit UK Limited 66, 72 

DS SMITH CORREX (Trading as a division of DS 

Smith Plastics Limited) 163, 559 

DST Group Ltd 86 

Dubai Cable Company (Private) Limited, Trading 

as Ducab 559 

Dudley Safes Limited 253, 260, 559 

Duplus Architectural Systems Limited 559 

DuPont de Nemours (Luxembourg) S.a.r.l. 520 

E 

E&S Heating & Ventilation Ltd 7 

Elta Fans Limited 239 

EMCOR Facilities Services Limited, EMCOR 

Specialist Services 560 

Emirates Fire Fighting Equipment Factory L.L.C. 

(FIREX) 560 

Energy Control Systems Ltd 536 

Envirowrap Solutions Limited 164, 173, 560 

Essex Safety Glass Limited 512, 560 

Eton Fire Limited 561 

Eurobond Laminates Limited & Eurobond Doors 

Limited 20, 37, 44, 561 

Eurobrick Systems Limited 531 

Euroclad Limited 22, 51, 561 

Euroform Products Limited 529 

Everday Technology Co. Limited 562 

Excel Industries Ltd 38, 562 

Eyston Company Ltd 562 

F 

F.V.S. Limited 562 

Fendor Limited 7, 414, 426, 562 

FES Limited, FES Sprinklers 563 

FFE Fire & Security Limited 563 

Fike Safety Technology Ltd 563 

Filling and Packing Materials Manufacturing 

Company (F.I.P.C.O.) 563 

Fire Alarm Solutions Limited 563 

Fire Defence (Northern) Limited 564 

Fire Defence plc 564 

Fire Logistics Limited 564 

Fire Protection Limited 7, 230, 564 

Fire Protection Solutions Ltd 8 

Fire Queen Limited 564 

Fire Security (Sprinkler Installations) Limited 565 

Fireproof Fire Engineering Limited 565 

Firespray International Limited 231, 565 

Firetecnics Systems Limited 565 

First Fire Protection Limited 565 

Flameshield Products Limited 233 

Flameshield Products Limited (Incorporating 

Flameshield Limited) 8, 566 

Flexiform Business Furniture Limited-incorporating 

Asgard Secure Steel Storage 566 

Florprotec Limited 164 

Fortress Doors N.I. Limited 566 

Franklin Hodge Industries Ltd. 566 

Frontier-Pitts Limited 492 

Fusion Building Systems 525 

G 

G & A Fire Protection Ltd 4, 8 

Galglass Limited 566 

Gaocheng General Foundry 567 

Gardner & Co (Kent) Ltd 8 

Giffen Group 9 

Gilray Plant Limited 165, 173 

Globe Fire Sprinkler Corporation 567 

Gloucester Composites Limited 567 

Godrej & Boyce Mfg. Co. Ltd. (Security Equipment 

Division) 254, 260 

Godwin Pumps Limited 567 

Goran Plastics 165, 567 

Gordonson Fire Protection Limited 568 

Grange Door Systems 206, 209, 568 

Grundfos Fire Systems 568 

gte Brandschutz AG 195, 568 

Gulf Security Technology Co. Ltd - A UTC Fire & 

Security Company 568 

Gunfire (Gunite Eastern Limited) 9 

Guthrie Douglas Limited 569 

GW Sprinkler A/S 569 

H 

H S Jackson & Son (Fencing) Limited, t/a 

Jacksons Fencing 476, 569 

H&S Decorating Specialists Ltd 9 

Haes Systems Limited 570 

Hall & Kay Fire Engineering (Manchester) 570 

Hall & Kay Fire Engineering (Paisley) 570 

Hall & Kay Fire Engineering (Thame) 570 

Hall & Kay Fire Engineering (West Midlands) 570 

Hall Fire Protection Limited 571 

Hallmark Fire (a division of SFS Fire Services Ltd) 

571 

Halton Foodservice Limited 244, 571 

Handan Boate Foundry Co Limited 571 

Hart Door Systems 196, 206, 571 

Harvel Plastics Incorporated (Bakersfield) 572 

Harvel Plastics Incorporated (Easton) 572 

Hemsec Manufacturing Limited 23, 52, 572 

Henry Lewis and Sons (Wireworkers) Limited 434, 

572 

Heras U.K. Fencing Systems 478, 572 

Hersey Meters 573 

Hershey Valve Co Limited 573 

Hillmoore Fire Protection Ltd 9 

Hilti (Gt Britain) Limited 573 

Hilti Aktiengesellschaft 86 

Hochiki America Corporation 573 

Hochiki Corporation 573 

Hochiki Europe (UK) Limited 574, 625 

Honeywell Life Safety Systems UK 574 

Honeywell Security UK Limited 574 

xii 20 Nov 2011

INDEX 

Horing LIH Industrial Co Ltd 574 

Hörmann KG Freisen 196 

Hosiden Besson Limited 575 

Huzhou Jiusheng Electric Co Ltd 575 

I 

Iceberg Building Services Limited 575 

Icopal Limited 77, 165, 174 

Icopal S. A. 471, 575 

IKO PLC 79 

Industrial Door Engineering Limited 197, 206, 209, 

575 

Industrial Textiles & Plastics Ltd 166, 174, 520 

Influx Measurements Limited 576 

Intelligent Engineering (UK) Ltd 517 

IPB N.V. 166, 576 

IR Martin Roberts, IR Security & Safety Limited 

326, 421, 423 

Irish Driver-Harris Company Limited 576 

Irish Industrial Tanks Limited 576 

Irish Sprinkler & Fire Protection Limited 576 

ISOCAB France S.A. 24, 53 

Isoclad Limited 54, 270, 460, 577 

J 

J & J Design Limited 577 

J Durrance & Co Ltd 198, 577 

J W Singer 625 

J. Bryceland Fire Systems Ltd 577 

Jeld-Wen UK Ltd 186 

John Brash & Company Ltd 531 

K 

K.P.F.P. Limited 578 

KAC Alarm Company Limited 578 

Kean Building & Fire Protection Services Limited 

578 

Kentallen Fire Protection Limited 578 

Kentec Electronics Limited 578 

Key Housing Limited 525 

Keystone Electric Wire & Cable Company Limited 

579 

Kidde Products Ltd, trading as AirSense 

Technology 579 

Kingfell Plc 579 

Kingspan Door Components S.A. 579 

Kingspan Insulation Limited 24, 580 

Kingspan Limited (t/a Profiles and Sections) 522, 

534 

Kingspan Ltd 25, 56, 580, 626, 629 

Kingspan Ltd trading as Kingspan Structural, 

Kingspan Fabrications, Kingspan Controlled 

Environments (KCE), Kingspan Profiles and 

Sections 580, 626, 629 

Kingspan Ltd. 27, 57, 580, 626, 630 

KingspanTarec Industrial Insulation Limited 581, 

626 

Klober Limited 521 

KME Italy SpA 581 

Kone PLC 206, 210 

L 

L.B.S. Group (incorporating L.B.S Security 

Services Limited - t/a Specialized Door 

Services, Russell Shutters, Olsen Shutters and 

Ranford Doors) 198, 210, 581 

Landskroon B.V. 166, 175 

Liddle Doors Limited 275, 328, 415, 435, 495, 581 

Lincs Doors Limited 198, 581 

Lingjack Engineering Works PTE Ltd 582 

Linkester Fire Protection Limited 582 

Lion Steelworks SDN. BHD. 257, 582 

Lixil Nittan Company Limited 582 

Lixil Nittan Electronic Company Limited 582 

Logix UK Limited (Simplipac) 534 

Lowrey Contractors Limited 275, 331, 418, 436, 

465, 583 

LPG Tecnicas en Extincion de Incendios, S.L. 583 

Lubrizol Advanced Materials Europe B.V.B.A 583 

M 

M & P Fire Solutions Ltd 584 

M J Quinn Integrated Services Ltd 10 

M. J. Quinn Integrated Services Limited 584 

Mansell Construction Services LTD 10 

Map Ventilation Limited 10 

Marmorit (UK) GmbH 532 

Mavili Elektronik Ticaret Ve Sanayi A.S. 584 

Max Frank Limited 515 

McAvoy Group Limited 179, 584 

MCT Brattberg AB 120, 180 

MECE Fire & Security Limited 585 

Mercian Shutters Limited 199, 207, 210, 585 

Mercury Engineering 585 

Metsec Limited 522 

Midas Technologies (GB) Limited 455, 585 

Middle East Insulation 199 

Midland Door Services Limited 585 

Midlands Fire Ltd 10 

MITIE McCartney Fire Protection Limited 586 

MITIE Property Services Limited - Midlands 4 

MITIE Technical Facilities Management Limited 

(MITIE Fire and Security Systems) 586 

Mitsubishi Plastics Inc 586 

Modgal Metal (99) Limited 587 

Modular Panel Systems Limited 28, 57 

Monarflex 167, 587 

Morgan Marine Limited 277, 587 

Morley-IAS Fire Systems By Honeywell 587 

MultiSteel Limited 415, 467 

N 

N.V. Joris IDE 29, 588 

Nanjing Fire Protection Technology Co Limited 588 

National Fire Fighting Manufacturing Company 

Limited (NAFFCO) 588 

National Sprinkler Company Limited 588 

Nexans Turkiye Endustri ve Ticaret A.S. 589 

NIBCO Inc 589 

Nields Plastic Company Limited 167, 589 

Nitin Fire Protection Industries Limited 589 

Nittan (UK) Limited 590 

Nittan Fire Protection System (Zhongshan) 

Company, Limited 590 

NK Fencing Limited 482 

NMC (UK) Limited 590 

20 Nov 2011 xiii

INDEX 

No Climb Products Limited 590 

Nobel Fire Systems 590 

Northern Ireland Plastics Limited 167, 591 

Notifier Fire Systems by Honeywell 591 

Nu-Form Fire UK Limited 591 

O 

Ockwells Limited 167, 172 

Olympic Fire Protection Limited 591 

O'Mahony Contractors Ltd 11 

Ondaplast SpA 168 

P 

P&M Group Ltd trading as ISD 4, 11 

Pace Technology Co. Limited 591 

Panel Projects Limited 58, 592 

Paneltex Limited 38 

Paroc Panel System Oy Ab 58, 592 

Patterson Pump Ireland Limited 592 

PEL Services Limited 592 

Pendle Designs Limited 592 

Peripheral Support Services Limited 593 

Permanite Asphalt 83 

PermaRock Products Limited 532 

Pittway Tecnologica Srl. 593 

Portakabin Ltd 41 

Potter Electric Signal Company 593 

Powershield Doors Limited 332, 593 

Pressex UK Limited 264, 593 

Prestige Fire Door Services Limited 207 

PRO TEC Vinduer A/S 431 

Professional Barrier Systems Limited279, 436, 594 

Project Fire Products Limited (incorporating 

Project Fire Engineers) 594, 626 

Promat UK Ltd 60, 132, 155 

Protec Camerfield Limited 594 

Protec Fire Detection plc 594 

Protec International Limited 168, 172, 175, 595, 

627 

Protecta Screen Ltd 169 

Provincial Sprinkler Co. Limited 595 

Prysmian Cables & Systems Limited 595 

Prysmian Cables & Systems Ltd 595 

Prysmian Power Cables & Systems Australia Pty 

Limited 596 

PSF Wales Limited 279, 339, 596 

Pyrotherm Ltd 11 

Q 

Qinhuangdao Taidy Flex-Tech Co. Ltd 596 

Quinn Therm Limited 30, 596 

R 

R & D Sheetmetal Limited 281, 340 

R & S Fire & Security Services Limited 596 

R Lewis & Co. (UK) Ltd 11 

RAMCRO S.p.A 597 

Rapidrop Global Limited 597 

Recticel Insulation Products / Recticel N.V 30 

Red Rose Fire Protection Limited 597 

Reliable Fire Sprinkler Limited 597 

Retainagroup Limited 501, 504, 598 

RGB Integrated Services Limited 598 

RGT Fire Protection Limited 598 

Richmond Fire Engineers Limited 598 

RMD Fire Control Limited 599 

Robust UK Limited 599 

Rockwool Limited 31, 67, 84, 85, 121, 152, 177, 

181, 234, 599 

Rolland Sprinklers 599 

Ross Fire Protection Limited 599 

Rotary Firematic Limited 600 

Rotherham CNC Ltd 600 

RSM Refko Installations Limited 600 

Ruskin Air Management Limited 627 

Ruukki Construction Oy 60 

Ruukki Polska Sp. z.o.o 32 

Ruukki Polska Sp. Z.o.o. 600 

S 

S.F.S. FIRE SERVICES LIMITED (trading as Hall 

& Kay Fire Engineering and Chubb Fire 

Mechanical Division) 600 

S.F.S. Fire Services Ltd, T/A Hall & Kay Fire 

Engineering 601 

Safe Partnership 207, 211, 346, 601, 627 

SafeGuard Doors, A Division of Adams Rite 

Europe Limited 346, 601 

Safeguard Security, a trade name of WBH 

Industries 437, 601 

Safety Hi-Tech Srl 601 

Safety Technology International (Europe) Limited 

602 

Saint-Gobain Weber Limited 519 

Salisbury Glass Centre Limited 422, 424, 432, 602 

Sanwa Yoshida (JiaXing) Construction Material 

Industry Co., Ltd 602 

SAPAG Industrial Valves 602 

Saudi Factory For Fire Equipment Co. 200, 602 

Schlumberger Oilfield UK PLC, Sensor Highway 

Limited (Schlumberger, Southhampton) 603 

Scotshield Limited 603 

Sealed Air Limited 169 

Security Blinds Limited 438, 603 

Sekisui Aqua Systems Company Limited 603 

Select Fire Services Limited 604 

Selectaglaze Limited 427, 604 

Selectamark Security Systems plc 502, 504, 604 

Shaanxi J & R Fire Fighting Co Ltd 604 

Shakun Polymers Limited 604 

Shellcast Systems Limited 446, 605 

ShenZhen CICAM Manufacturing Co Ltd 605 

Shurjoint Metals Inc. 605 

Siemens plc, Building Technologies, Fire Safety 

Division 605 

Siemens Switzerland Limited, Building 

Technologies Division 606 

SigNET AC Limited 606 

Simbars (UK) Limited 439, 606 

SIP Energy Ltd 526 

SMP Security Limited 257, 261, 607 

Solent Fire Protection Services Limited 607 

Solicom SA 170, 175 

Sotech Limited 69, 75, 607 

Southern Grille & Gate Limited 607 

xiv 20 Nov 2011

INDEX 

Spears Manufacturing Company Inc 607 

Specialist Panels UK Limited 62, 608 

SpeedDeck Building Systems Limited 32 

SPIE Fire (A division of SPIE) 608 

SPIE Matthew Hall 608 

SPP Pumps Limited 609, 627 

Sprue Safety Products Ltd 609 

Stafford Bridge Doors Limited 347, 416, 450 

Stanair Industrial Door Services Limited 211, 610 

Stancold plc 62, 610 

Static Systems Group Plc 610 

Steeltech Systems Limited 610 

Steelway Fensecure Limited t/a Steelway 

Brickhouse 456 

STO AG 610 

Sto Ltd 67, 73 

Stobich Brandschutz GmbH 201 

Stopfire Ltd 12 

Stroma Contracting Ltd 12 

Sunjüt A.S. 170, 176, 611 

Sunray Engineering Limited 201, 207, 360, 417, 

611 

Superglass Insulation Limited 85 

Supra UK Limited 611 

Sure Lock Doors Limited 611 

Surelock McGill Group 612 

SuZhou Primetech Electronics Co Limited 612 

SWS UK 439, 447, 449, 453, 612 

System Sensor 612 

System Sensor de México S.A. de C.V. 613 

System Sensor Fire Detectors 613 

System Sensor, Honeywell International (I) PVT. 

Limited 613 

T 

Talentum Developments Limited 613 

TangoRail Limited 484, 613 

Taylor Fire Sprinklers Limited 614 

Technocover Limited (incorporating TechnoRail 

and Strataform) 203, 282, 376, 419, 450, 458, 

468, 496, 614, 628 

Terofire Products 614 

Thameside Fire Protection Co. Limited 614 

The Blinking Lamp Company Ltd 170, 176 

The Expanded Metal Company Limited 440, 469, 

487, 490 

The Reliable Automatic Sprinkler Co., Inc, 614 

The Rooflight Company 430, 615 

The Safety Letter Box Company Limited 508 

The Viking Corporation 615 

Thermal Engineering Contracts Ltd 12 

Thermotech Fire Protection Limited 615 

ThyssenKrupp Steel Europe AG 33 

Tindall Engineering Limited 615 

Total Polyfilm Limited 171, 615 

Tratos Cavi SpA 616 

Trellicor (Pty) Limited 441, 449, 616 

Trimetals Limited 286, 616 

Trimo d.d 34, 39, 63 

Twinplast Limited 171, 616 

Tyco Building Services Products B.V. 616 

Tyco Fire & Building Products 617 

Tyco Fire and Integrated Solutions (the trading 

company for Tyco Fire and Integrated Solutions 

(UK) Limited and Tyco Fire and Integrated 

Solutions (Ireland) Limited) 211, 212, 617 

Tyco Fire Products Manufacturing Limited 619, 628 

Tyco Flow Control (M) Sdn. Bhd. (Tyco Fire 

Suppression & Building Products, Malaysia) 619 

Tyco Thermal Controls UK Ltd 619 

U 

UK Fire Safety Limited 619 

UK Firewatch Limited 620 

Ultra Suppression Systems Limited 620 

Univar Speciality Consumables 171 

Universal Fixings Limited 620 

UTC Fire & Security (Africa) trading as Ziton 620 

UTC Fire & Security Americas Corporation, Inc. 

621 

UTC Fire & Security B.V. 510 

UTC Fire & Security Services 621 

V 

Ventcroft Limited 621 

Victaulic Company 621, 622 

Viking Plastics 622 

Vimpex Limited 622 

Vipond Fire Protection Limited 623 

Visqueen Building Products 521 

Vulcan Tanks Limited 623 

W 

Wagner Group GmbH 623 

Weber, Saint-Gobain Weber Limited 68 

WebWayOne Ltd 250 

Wienerberger Limited 533 

WOPF Befestigungselemente GmbH 623 

Wrexham Mineral Cables 623 

Writech Industrial Services Limited 624 

X 

Xi'an System Sensor Electronics Limited 624 

Xtratherm Limited 34, 624 

Xtratherm UK Limited 624, 628, 630 

Y 

Yorkon Limited 41 

Yorkshire Building Services (Whitwell) Limited 529 

Z 

Zeta Alarm Systems by GLT Exports Limited 624 

Z-Led Limited 533 

20 Nov 2011 xv

Part 

1 

BUILDING PRODUCTS

PART 1: BUILDING PRODUCTS 

INTRODUCTION 

The specification and installation of building products and systems that provide passive fire protection is a 

fundamental aspect of fire safety. Correctly specified and installed passive fire protection products and 

systems will deliver a building that resists the incidence of fire to best effect, and in turn provide safety for the 

occupants and firefighters, and will reduce the potential for property loss. 

In England and Wales, Building Regulations define requirements to ensure the health and safety of those who 

occupy or visit buildings. Guidance on how to comply with the Building Regulations in England and Wales is 

given in a series of Approved Documents. Approved Document B provides guidance in respect of fire safety. 

In other territories, other regulations will apply as laid down by the Authority Having Jurisdiction (AHJ). For 

Scotland, Building Regulations guidance is provided by the Domestic and Non-Domestic Technical Handbook 

and Northern Ireland Building Regulation guidance is provided by the Department of Finance (DFP) Technical 

Booklet E. 

Passive fire protection is a combination of design, assembly and material choice. This will include: 

Protection of structural elements 

Materials that do not contribute to fire growth 

Limited toxicity of combustion products 

Walls and floors that provide compartments to resist the spread of fire 

Provision of a building envelope to resist fire entering from outside 

In addition to careful design and product selection, it is recommended that all products are installed by LPCB 

approved contractors who have demonstrated their competence. 

Listings in this section include: 

Products 

- Partitions 

- Structural steel protection 

- Fire stopping/penetration seals 

- Products used in transport applications 

- Walls and roofs/roofing - the building envelope - 

- Protective sheeting 

- Temporary buildings for use on site 

These products are approved in accordance with various standards, the details of which are given at the front 

of each section. 

Installation contractors 

Contractors are approved in accordance with: 

LPS 1500: Requirements for the approval and listing of companies installing construction elements used to 

provide compartmentation in buildings. 

LPS 1531: Requirements for the approval and listing of companies installing or applying passive fire 

protection products. 

2 20 Nov 2011

PART 1: SECTION 1 

APPROVED INSTALLERS OF PASSIVE FIRE PROTECTION PRODUCTS 

A fundamental aspect of fire safety in buildings is the specification and installation of ‘built in’ or passive fire 

protection products and systems. It has long been recognised that the performance of a product can be 

severely undermined by poor installation or application leading to failure in the event of a fire. This has led to 

the recent development of LPS 1500 Requirements for the LPCB approval and listing of companies installing 

construction elements used to provide compartmentation in buildings and LPS 1531 Requirements for the 

approval and listing of companies installing or applying passive fire protection products. Both these schemes 

help to ensure that companies installing passive fire protection : 

· Have sufficient training and expertise to install the products or systems using the correct techniques. 

· Use products where it can be demonstrated that they will meet the required fire performance. 

· Have access to up to date installation instructions for the installed systems. 

· Carry out and record in process inspection checks prior to, during and after the product or system 

installation. 

· Issue LPCB Certificates of Conformity for each installation. 

LPS 1500 was developed specifically for companies installing fire resisting compartmentation systems 

approved by the LPCB to LPS 1208. 

LPS 1531 is an installer scheme that covers all the major product areas of passive fire protection. 

20 Nov 2011 3

PART 1: SECTION 1.1 

LPS 1500 APPROVED INSTALLER OF FIRE RESISTING COMPARTMENTATION SYSTEM 

The companies listed in this section are approved installers of fire resisting compartmentation systems 

approved by LPCB to LPS 1208. 

LPS 1208 Approved products for use in the following elements of construction may be installed under this 

scheme. 

Loadbearing compartment walls and partitions 

Non-load bearing compartment walls and partitions 

External walls 

Curtain walls 

Cavity barriers 

Roofs where fire resistance is required (loadbearing and non-loadbearing) 

Loadbearing compartment floors 

Insulated panels used for enclosing production and storage areas in food factories. 

G & A Fire Protection Ltd 

Helions Bumpstead Road, Haverhill, Suffolk CB9 7AA, United Kingdom 

Tel: +44 (0) 1440 714650 • Fax: +44 (0) 1440 713371 

E-mail: info@ga-group.com • Website: www.ga-group.com 

Certificate No. 889PIb to LPS 1500 Issue 2 

Installer of fire resisting compartmentation systems to LPS 1500 

MITIE Property Services Limited - Midlands 

2 Colwick Quays Business Park, Private Road No.2, Colwick, Nottingham NG4 2JY, United Kingdom 

Tel: 0115 940 1770 • Fax: 0115 940 2232 

E-mail: malcolm.williams@mitie.com • Website: www.mitie.com 

Northern Office 

MITIE Property Services Limited, Meiklewood Gate, 35 Meiklewood Road, Glasgow G51 4GB, United 

Kingdom 

E-mail: Steven.Elliot@mitie.co.uk • Website: www.mitie.com 

Certificate No. 769a to LPS 1500: Issue 2.0 

Installer of Fire Resisting Compartmentation Systems to LPS 1500 

P&M Group Ltd trading as ISD 

Unit A, 125 Business Park, Llanthony Road, Gloucester, Glos GL2 5JQ, United Kingdom 

Tel: +44 (0) 1452 520649 • Fax: +44 (0) 1452 301910 

E-mail: sales@isdcoldstores.co.uk • Website: www.isdcoldstores.co.uk 

Certificate No. 1008PIa to LPS 1500 Issue 2.0 

Installer of fire resisting compartmentation systems to LPS 1500 

4 20 Nov 2011


LPS 1531 APPROVED INSTALLER OF PASSIVE FIRE PROTECTION PRODUCTS 

The companies listed in this section are approved to install passive fire protection products for the Appendix 

areas indicated in their entry. 

Appendix areas: 

1. Penetration, cavity barrier and linear gap seals 

2. Fire rated board and cladding to structural elements 

3. Intumescent coatings to structural elements 

4. Fire rated spray materials 

5. Fire rated ductwork systems 

6. Fire resisting dampers 

7. Fire resistant compartment wall systems 

8. Offsite application of intumescent coatings to structural elements 

Abbey Thermal Insulation Ltd 

23-24 Riverside House, Lower Southend Road, Wickford, Essex SS11 8BB, United Kingdom 

Tel: +44 (0) 1268 572116 • Fax: +44 (0) 1268 572117 

E-mail: robert.stubbs@abbeythermal.com 

Certificate No. 1014PI to LPS 1531: Issue 1.0 

Company assessed and approved for installation of passive fire protection products under the following scope. 

Appendix 1 - Penetration, cavity barrier and linear gap seals. 

Appendix 2 - Fire rated board and cladding to structural elements. 

Appendix 5 - Fire rated ductwork systems. 

Avert Fire (UK) Ltd 

P O Box 248, Dawes lane, Scunthorpe DN16 1DW, United Kingdom 

Tel: +44 (0)1724 853712 • Fax: +44 (0)1724 278848 

E-mail: admin@avertfire.co.uk; kevin@avertfire.co.uk • Website: www.avertfire.co.uk 



Appendix 1 - Penetration, cavity barriers and linear gap seals. 

Bryen & Langley Limited 

48-60 Footscray Road, Eltham, London SE9 2SU, United Kingdom 

Tel: +44 (0)20 8850 7775 • Fax: +44 (0)20 8850 6772 

E-mail: AEscudier@bryen-langley • Website: www.bryen-langley.com 

Certificate No. 897Pl to LPS 1531: Issue 1.0 



20 Nov 2011 5



Checkmate Fire Solutions Ltd 

Head Office: 

Royd House, 11 Birds Royd Lane, Brighouse, West Yorkshire HD6 1LQ, United Kingdom 

Tel: 01484 721154 • Fax: 01484 723152 

Southern Office: 

Unit 1, Woodgates Farm, Woodgates End, Dunmow, Essex CM6 2BN, United Kingdom 

Tel: +44 (0)1279 850021 • Fax: +44 (0)1279 850261 

E-mail: info@checkmatefire.com • Website: www.checkmatefire.com 



Appendix 1 - Penetration, cavity barriers and linear gap seals 

Appendix 2 - Fire rated board and cladding to structural elements 

Appendix 3 - Intumescent coatings to structural elements 

Cleshar Contract Services Ltd 

Heather Park House, North Circular road, Stonebridge, London NW10 7NN, United Kingdom 

Tel: +44 (0) 20 8733 8888 • Fax: +44 (0) 20 8733 8899 

E-mail: chris.carter@cleshar.co.uk / jeremy.ilott@cleshar.co.uk • Website: www.cleshar.co.uk 

Certificate No. 944PI to LPS 1531 



Corecut Fire Protection (a division of Corecut Limited) 

Bankhead, Broxburn, West Lothian EH52 6PP, United Kingdom 

Tel: +44 (0) 1506 854710 • Fax: +44 (0) 1506 853068 

E-mail: office@courecut.co.uk • Website: www.corecut.co.uk 




Appendix 3 - Intumescent coatings to structural elements. 

CVD Fire Protection Ltd 

Unit 1A, East End Farm Estate, Lanark Road, Carstairs, Lanarkshire ML11 8QG, United Kingdom 

Tel: +44 (0) 845 450 1601 • Fax: +44 (0) 845 450 1602 

E-mail: info@cvdfire.co.uk • Website: www.cvdfire.co.uk 

Certificate No. 1009PI to LPS 1531 Issue 1.0 



6 20 Nov 2011





David Tyrrell T/A Nene Valley Acoustics 

2a New Street, Irthlingborough, Northamptonshire NN9 5UG, United Kingdom 

Tel: +44 (0) 1933 650650 • Fax: +44 (0) 1933 704830 

E-mail: David_Tyrrell@btconnect.com 

Certificate No. 1021PI to LPS 1531 Issue 1 



E&S Heating & Ventilation Ltd 

Diplocks Way, Hailsham, East Sussex BN27 3JF, United Kingdom 

Tel: +44 (0) 1323 845492 • Fax: +44 (0) 1323 440577 

E-mail: emmacollins@esgroup.co.uk • Website: www.esgroup.co.uk 




Fendor Limited 

Heworth House, William Street, Felling, Gateshead NE10 0JP, United Kingdom 

Tel: +44 (0)191 438 3222 • Fax: +44 (0)191 438 1686 

E-mail: av@fendor.co.uk • Website: www.fendor.co.uk 

Certificate No. 712c to LPS 1531 Issue 1.0 



Fire Protection Limited 

Flamebar House, South Road, Templefields, Harlow, Essex CM20 2AR, United Kingdom 

Tel: +44 (0)1279 634 230 • Fax: +44 (0)1279 634 231 

E-mail: info@fireprotection.co.uk • Website: www.fireprotection.co.uk 

Certificate No. 277b to LPS 1531: Issue 1.0 

Company assessed and approved for installation of passive fire protection products under the following scope: 


20 Nov 2011 7



Fire Protection Solutions Ltd 

1-3 Highway Point, 239 Torrington Avenue, Coventry CV4 9AP, United Kingdom 

Tel: +44 (0) 845 0538989 • Fax: +44 (0) 2476 465568 

E-mail: fpcltd@btconnect.com • Website: www.firecontractor.co.uk 






Flameshield Products Limited (Incorporating Flameshield Limited) 

4 The Limes, Ingatestone, Essex CM4 0BE, United Kingdom 

Tel: +44 (0)1277 352202 • Fax: +44 (0)1277 355419 

E-mail: info@flameshield.org • Website: www.flameshield.org 

Certificate No. 785b to LPS 1531 Issue 1 



G & A Fire Protection Ltd 

Helions Bumpstead Road, Haverhill, Suffolk CB9 7AA, United Kingdom 

Tel: +44 (0) 1440 714650 • Fax: +44 (0) 1440 713371 

E-mail: info@ga-group.com • Website: www.ga-group.com 

Certificate No. 889PIa to LPS 1531: Issue 1.0 




Appendix 3 - Intumesent coatings to structure elements 

Gardner & Co (Kent) Ltd 

1 - 5 Bermondsey Street, London SE1 2ER, United Kingdom 

Tel: 020 7403 5894 • Fax: 020 7378 0316 

E-mail: enquiries@gardnerco.net • Website: www.gardnerco.net 




8 20 Nov 2011



Giffen Group 

Lyon Way, St Albans, Hertforshire AL4 0LQ, United Kingdom 

Tel: +44 (0)1727 869126 

E-mail: dan.bliss@giffengroup.co.uk • Website: www.giffengroup.co.uk 



Appendix 1 - Penetration, cavity, barriers and linear gap seals. 

Gunfire (Gunite Eastern Limited) 

Endeavour House, Compass Point, St Ives, Cambridgeshire PE27 5JL, United Kingdom 

Tel: +44 (0)1480 466880 • Fax: +44 (0)1480 308999 

E-mail: admin@gunite.co.uk • Website: www.gunite.co.uk 





H&S Decorating Specialists Ltd 

1 Wellesley Avenue, Richings Park, Iver, Bucks SL0 9AU, United Kingdom 

Tel: +44 (0)1753 654123 • Fax: +44 (0)1753 654345 

E-mail: info@hsgroup.co.uk • Website: www.hsgroup.co.uk 




Hillmoore Fire Protection Ltd 

Unit 17-18 Woodlands Farm, Spring Lane, Cookham Dean, Berkshire SL6 9PN, United Kingdom 

Tel: +44 (0)1628 890122 • Fax: +44 (0)1628 478543 

E-mail: info@ hillmoorefire.co.uk • Website: www.hillmoorefireprotection.co.uk 




Appendix 7 - Fire resistanct compartment wall system. 

20 Nov 2011 9



M J Quinn Integrated Services Ltd 

119 Farringdon Road, London EC1R 3DA, United Kingdom 

Tel: 0207 239 8750 • Fax: 0207 239 8751 

E-mail: BOHara@mjquinn.co.uk • Website: www.mjquinn.co.uk 




Mansell Construction Services LTD 

Rink Road, Ryde, Isle of Wight PO33 1LP, United Kingdom 

Tel: +44 (0) 1983 563668 • Fax: +44 (0) 1983 615600 

E-mail: kbloomfield@mansell.plc.uk • Website: www.mansell.plc.uk 




Appendix 7 - Fire resistant compartment wall systems. 

Map Ventilation Limited 

Hanwiz House, Milner Way, Ossett, Wakefield WF5 9JG, United Kingdom 

Tel: 01924 278175 • Fax: 01924 278126 

E-mail: info@mapventilation.co.uk • Website: www.mapventilation.co.uk 



Appendix 5 - Fire rated ductwork systems 

Midlands Fire Ltd 

Unit D8 The Ropewalk Industrial Estate, The Ropewalk, Ilkeston, Derbyshire DE7 5HX, United Kingdom 

Tel: +44( 0) 115 932 9548 • Fax: +44 (0) 845 009 5727 

E-mail: info@midlandsfire.co.uk • Website: www.midlandsfire.co.uk 


Company assessed and approved for installation of passive fire protection products under the following scope: 



10 20 Nov 2011



O'Mahony Contractors Ltd 

60 Middle Road, Higher Denham, Buckinghamshire UB9 5EQ, United Kingdom 

Tel: 01895 833553 • Fax: 01895 835003 

E-mail: gary@omahonycontractors.com • Website: www.omahonycontractors.com 





P&M Group Ltd trading as ISD 

Unit A, 125 Business Park, Llanthony Road, Gloucester, Glos GL2 5JQ, United Kingdom 

Tel: +44 (0) 1452 520649 • Fax: +44 (0) 1452 301910 

E-mail: sales@isdcoldstores.co.uk • Website: www.isdcoldstores.co.uk 

Certificate No. 1008PIb to LPS 1531 Issue 1.0 





Pyrotherm Ltd 

8 Jensen Court, Astmoor Industrial Estate, Runcorn, Cheshire WA7 1SQ, United Kingdom 

Tel: +44 (0)1928 565641 • Fax: +44 (0) 1928 565648 

E-mail: paulbusow@pyrotherm.co.uk • Website: www.pyrotherm.co.uk 






R Lewis & Co. (UK) Ltd 

Unit 7 and 8, Parklands Industrial Estate, East Moors Road, Cardiff CF24 5JP, United Kingdom 

Tel: +44 (0) 2920 215716 • Fax: +44 (0) 2920 406205 

E-mail: chris@rlewisandcoukltd.com • Website: www.rlewisandcoukltd.com 






20 Nov 2011 11



Stopfire Ltd 

Units 22, 23, 24 & 32 Dryden Road, Loanhead, Midlothian EH20 9LZ, United Kingdom 

Tel: +44(0)131 448 0555 • Fax: +44(0)131 448 0556 

E-mail: mail@stopfire.net • Website: www.stopfireltd.com 






Stroma Contracting Ltd 

Stroma House, Unit 4, Pioneer Way, Castleford WF10 5QU, United Kingdom 

Tel: +44 (0)845 621 1111 • Fax: +44(0)845 621 1112 

E-mail: contracting@stroma.com • Website: www.stroma.com 

Certificate No. 967PI to LPS 1531: Issue 1 




Appendix 3 - Intumescent coatings to structure elements. 

Thermal Engineering Contracts Ltd 

38 Whitehouse Street, , Leeds LS10 1AD, United Kingdom 

Tel: +44(0) 1132 430254 • Fax: +44(0) 5603 430284 

E-mail: info@tecl.uk.com • Website: www.tecl.uk.com 




12 20 Nov 2011


CONSTRUCTION PRODUCT SYSTEMS (BUILDING ENVELOPE, ROOFING & PARTITIONS) 

This section includes the reaction to fire and fire resistance approval schemes for construction systems 

including building envelope, roofing and partitions. 

This section includes: 

Section 2.1 

Section 2.1.1 

Section 2.1.2 

Section 2.1.3 

Section 2.1.4 

Section 2.2 

Section 2.3 

Section 2.3.1 

Section 2.3.2 

Section 2.4 

Section 2.4.1 

Section 2.4.2 

Section 2.5 

Section 2.5.1 

Section 2.5.2 

Section 2.6 

LPS 1181 Series 

LPS 1181 Lining materials 

LPS 1181-1 Cladding products used for the external envelope of buildings. 

LPS 1181-2 Sandwich panels or built-up panel systems used internally in a building. 

LPS 1181-3 (Draft) Cladding used in POD construction 

LPS 1208 Composite construction elements 

LPS 1581 External cladding systems on a masonry substrate 

LPS 1581 External thermal insulated cladding (ETICS) 

LPS 1581 Rain screen cladding systems (RSC) 

LPS 1582 External cladding systems supported by a structural steelwork frame 

LPS 1582 External thermal insulated cladding (ETICS) 

LPS 1582 Rain screen cladding system (RSC) 

Roofing products 

Protection against fire outside of the building 

Protection against fire from inside the building 

Reaction to Fire (RTF) classifications for Materials and Products 

20 Nov 2011 13


LPS 1181 SERIES 

The LPS 1181 series of fire growth standards cover the requirements for LPCB approval and listing of 

construction product systems. These standards evaluate the fire performance of sandwich panels, built-up 

cladding systems and other construction product systems to ensure they will not significantly contribute to fire 

growth in their defined end use applications as detailed in the following listings. 

The use and application of the LPS 1181 standards are as follows: 

 

 

 

 

 

The LPS 1181 series of standards cover sandwich panels and built up cladding systems including 

jointing and fixing methods, sealants, gaskets and flashings. 

The LPS 1181 series of standards are used by the insurance industry for property protection 

purposes. 

The requirements of the Building Regulations are not addressed by the LPS 1181 series of 

standards. 

The Building Regulations define the life safety requirements for buildings. 

Approved Document B (produced by Communities and Local Government) provides guidance on 

meeting the requirements of the Building Regulations for fire safety and utilises the test data from the 

applicable BS 476 series and/or the BS EN 13501 series of standards. 

The LPS 1181 series currently consists of the following parts: 

LPS 1181: Part 1 Requirements and tests for built-up cladding and sandwich panel systems for use as the 

external envelope of buildings - See Section 2.1.2 

LPS 1181: Part 2 Requirements and tests for sandwich panels and built-up systems for use as internal 

constructions in buildings - See Section 2.1.3 

LPS 1181: Part 3 (Draft) Requirements and tests for factory produced room modules (PODS) and building 

system modules - See Section 2.1.4 

Within the LPS 1181 series of standards there are a number of classifications and these are summarised as 

follows: 

 

 

Cladding systems used for the external envelope of buildings are tested to LPS 1181 part 1. Those 

products that pass the test are graded into 2 classes: - 

o 

o 

Grade EXT-A** - A product that satisfies both the requirements of LPS 1181: Part 1 and also 

demonstrates fire resistance through a fire resistance test as specified in LPS 1208 (see 

section 2.2). Such products meet the requirements for separating elements used for 

compartmentation. (** represents in minutes, the LPCB grading of insulation achieved during 

the fire resistance tests). 

EXT B - A product that satisfies the requirements of LPS 1181 part 1 only. 

Sandwich panels and built-up systems used internally in a building for the construction of cold stores, 

factory clean rooms, space separation etc are tested in the large-scale test in LPS 1181 part 2. Those 

products that pass the test are graded into 3 classes: - 

o INT 1 - A product that achieves a minimum fire resistance performance of integrity = 60 

minutes and insulation = 60 minutes and passes the requirements of the LPS 1181 part 2 

large-scale test with an enhanced thermal exposure. 

o INT 2 - A product that achieves a minimum fire resistance performance of integrity = 30 

minutes and insulation = 30 minutes and passes the requirements of LPS 1181 part 2 largescale 

test with a crib ignition source. 

o 

INT 3 - A product that passes the requirements of LPS 1181 part 2 large-scale test with a crib 

ignition source but has no fire resistance. 

14 20 Nov 2011


LPS 1181 SERIES 

A guide to example applications with the potential inception risks and associated LPS 1181 classes (part 1 

and 2) can be found in appendices 1, 3 and 4 of “Technical briefing: Fire performance of sandwich panel 

systems” published by the Association of British Insurers in May 2003. 

It is the responsibility of end users, whether they be specifiers, regulators, insurers, architects etc, to satisfy 

themselves that any performance claims made by the manufacturers are valid by reference to a relevant 

certificate, listing and/or test reports and that the product satisfies all the necessary regulatory and design 

requirements. This responsibility also extends to ensuring that the systems are installed correctly and in 

accordance with the manufacturer’s instructions. 

20 Nov 2011 15

PART 1: SECTION 2.1.1 

LPS 1181 LINING MATERIALS 

The products listed in this section are intended to provide an additional, separate internal lining material to 

improve the thermal insulation of light steel or concrete industrial, agricultural and storage buildings. The listed 

products are often installed during the refurbishment of such buildings. 

These products have been tested to ensure that they do not significantly contribute to a developing fire. The 

fire properties of these lining materials have been determined from the relevant criteria of the series of fire 

growth tests described in the LPS 1181 series of standards. 

The lining materials are designed to be installed where the fire risk assessment of the building indicates a low 

to medium risk. Where the fire risk assessment of the building indicates a high fire risk, then products 

approved to LPS 1181:Part 1 or Part 2, as listed in Sections 2.1.2 and 2.1.3 should be used. 

16 20 Nov 2011


LPS 1181-1 CLADDING PRODUCTS USED FOR THE EXTERNAL ENVELOPE OF BUILDINGS 

LPS 1181: Part 1 Requirements and tests for built-up cladding and sandwich panel systems for use as the 

external envelope of buildings. 

This standard determines the contribution to fire growth of built-up cladding and sandwich panel systems used 

as the external envelope of buildings. 

The test is a large scale test comprising setting fire to an open-ended enclosure, supported on a steel frame, 

from the sandwich panels or built-up cladding system. It evaluates the panels, the jointing methods and the 

supporting system including fixings, which gives an assessment of the true fire performance of the system 

which cannot be determined from traditional small scale reaction to fire tests, such as surface spread of flame 

or fire propagation tests. 

Products that have passed the test and have achieved LPCB approval are graded under the following 

designations:- 

Grade EXT-A** - A product that satisfies both the requirements of LPS 1181: Part 1 and also demonstrates 

fire resistance through a fire resistance test as specified in LPS 1208 (see section 2.2). Such products meet 

the requirements for separating elements used for compartmentation. (** represents in minutes, the LPCB 

grading of insulation achieved during the fire resistance tests). 

Grade EXT-B - A product that satisfies the requirements of LPS 1181: Part 1 only. 

A Steadman & Son 

(a division of SIG Trading Ltd), Warnell, Welton, Carlisle, Cumbria CA5 7HH, United Kingdom 

Tel: +44 (0)16974 78277 • Fax: +44 (0)16974 78530 

E-mail: info@steadmans.co.uk • Website: www.steadmans.co.uk 

Certificate No: 635a to LPS 1181:Part 1 

Composite Wall and Ceiling Panels 

Product Name Specification 

Thickness (mm) 

Specification Wall 

panel orientation (H/V) 

(note 1) 

AS35/1000 PIR 40, 60, 80, 100 & 

(ceiling panel) 

AS35/1000 PIR 

(wall panel) 

Fire Resistance 

Integrity/Insulation 

LPS 

1181-1 

Grade 

Core 

Material 

- - EXT-B PIR 635a/04 

120 

40 V - EXT-B PIR 

100 & 120 V 120/30 EXT-A30 PIR 635a/05 

60, 80, 100 & 120 V 120/15 EXT-A15 PIR 

Cert. 

No. 

Notes: 

1. Wall panel orientation, Horizontal or Vertical (H/V), relates to the long joint orientation. 

2. LPCB Ref 635a/04 and 635a/05 panels require external overlap stitching using 6.3mm diameter x 22mm steel screws at 300mm centres 

for wall panels and 450mm centres for ceiling panels. 

3. LPCB Ref 635a/04 and 635a/05, wall and/or ceiling side lap joints require a sealant tape (HP500 GCA butyl tape) to be applied during the 

installation. 

4. LPCB Ref 635a/05 maximum unsupported span shall be limited to 1.5m between supports. 

ArcelorMittal Construction Belgium NV 

Lammerdries 8, Industrieterrein Geel West Z4, B-2440 Geel, Belgium 

Tel: +32 14563943 • Fax: +32 14563952 

E-mail: eric.mees@arcelormittal.com • Website: www.arclad.be 

Certificate No: 939a to LPS 1181: Part 1 

20 Nov 2011 17



Composite Panels 

Product Name 

Specification 

Thickness 

(mm) 


(min) 

Integrity 


(min) 

Insulation 

Grade 

AMW 1000 (wall panel) 60, 80 & 100 - - EXT- 

B 

AMRW 1000 (wall & roof 40, 50, 60, 

- - EXTpanel) 

80 & 100 

B 

Core 

Material 

Cert. 

No. 

PIR 939a/01 

PIR 939a/02 

1. LPCB Ref. 939a/01 & 939a/02 Wall panels can be laid either vertically or horizontally. 

2. LPCB Ref. 939a/02 External side lap joints to be stitched at 300mm centres using Fastovis 5 6,3 x 35mm screws. 

Brucha Ges.m.b.H 

Rusterstrasse 33, A-3451 Michelhausen, Michelhausen, Austria 

Tel: +43 (2275) 5878 1800 • Fax: +43 (2275) 5875 1804 

E-mail: office@brucha.at • Website: www.brucha.com 

Certificate No: 900a to LPS1181: Part 1: Issue 1.1 

Product Name 

WP-F (wall and roof 

panels) 

Specification 


60, 80, 100, 120, 

150 

& 200 


(min) 

Integrity 


(min) 

Insulation 

Grade 

- - EXT- 

B 

Core 

Material 

Mineral 

Wool 

Cert. 

No. 

900a/01 

Notes: 

1. LPCB Ref. 900a/01 wall panels to be laid with long joint in vertical orientation only. 

CA Group Limited 

Evenwood Industrial Estate, Copeland Road, Evenwood, Co. Durham DL14 9SF, United Kingdom 

Tel: +44 (0)1388 834242 • Fax: +44(0)1388 834881 

E-mail: help@cagroup.ltd.uk • Website: www.cagroup.ltd.uk 

Certificate No: 443a to LPS 1181 Part 1: Issue 1 

Product Name 

Specification 

System 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

Twin-Therm Fire Wall 95 - 200 240 30 EXT-A30 Mineral wool 443a/02 

Twin-Therm Wall 50 - 220 - - EXT-B Glass wool 443a/03 

Twin-Therm Roof 50 - 220 - - EXT-B Glass wool 443a/04 

Plano-Therm Wall 147 - 281 EXT-B Glass wool 443a/05 

River-Therm Roof 218 - 263 EXT-B Glass wool 443a/06 

SolarWall Wall 324 - 543 EXT-B Glass wool 443a/07 

Plano-Therm Fire Wall 173 - 218 120 30 EXT-A30 Mineral wool 443a/08 

SolarWall Fire Wall 324 - 543 240 30 EXT-A30 Mineral wool 443a/09 

Notes: 

1. LPCB Ref. 443a/02, 443a/03, 443a/05, 443a/07, 443a/08 and 443a/09, Wall Panels can be laid vertically or horizontally. For full 

details contact C A Group 

2. LPCB Ref. 443a/02, 443a/03, 443a/05, 443a/07, 443a/08 and 443a/09, The base of wall systems must be supported. 

3. LPCB Ref. 443a/02, Twin-Therm Fire Wall: external sheet may be CA 32 1000R, CA 32 1000W, CA 40 1000RW, CA 45 1000W or 

CA ARC 50 930. 

4. LPCB Ref. 443a/03, Twin-Therm Wall: external sheet may be CA 32 1000R, CA 32 1000W, CA 40 1000RW, CA 45 1000W or CA 

ARC 

5. LPCB Ref. 443a/04, Twin-Therm Roof: external sheet may be CA 32 1000R 

6. All systems, Internal sheeting normally CA LT 17 1000S. Twin-Therm roof may be lined with CA 32 1000RL. 

18 20 Nov 2011



Corus Panels and Profiles 

Shotton Works, Flintshire CH5 2NH, United Kingdom 

Tel: +44 (0)1684 856600 • Fax: +44 (0)1684 856601 

E-mail: sales@coruspanelsandprofiles.co.uk • Website: www.coruspanelsandprofiles.com 

Certificate No: 460a to LPS 1181: Part 1 Issue 1 

Product Name 

System 

Specification 

Thickness 

(mm) 

Wall panel 

orientation 

(H/V) 

(note 1) 


(minutes) 


Grade 

Core 

material 

Trimapanel wall panel 70 H 240/16 EXT- PIR* 460a/13 

A15 

90 H 240/27 EXT- PIR* 

A30 

70 and 90 V or H - EXT-B PIR* 

Built up wall (System W1) 160-220 V 240/30 EXT- Mineral wool 460a/14 

A30 

80-220 V 240/15 EXT- Mineral wool 

A15 

Built up roof (System R1) 60-220 - - EXT-B Mineral wool 460a/15 

Built up roof (System R2) 60-220 - - EXT-B Mineral wool 460a/16 

Trinsul wall and roof system 90 - - EXT-B Mineral wool 460a/19 

- - 240/60 EXT- Mineral wool 

A60 

Structural Liner Tray Roof 

190 - - EXT-B PIR* / Mineral 460a/20 

system 

wool 

Structural Liner Tray Wall 

system 

170 V - EXT-B PIR* / Mineral 

wool 

170 V 120/15 EXT- 

A15 

PIR* / Mineral 

wool 

Structural Flat Metal Roof 

50-200 - - EXT-B Mineral wool 460a/21 

Deck 

Stratatherm façade 80-150 H - EXT-B Mineral wool 460a/22 

Built up acoustic wall and roof 

175 V - EXT- Mineral wool 460a/23 

systems 

A15 

Built up acoustic wall system 175 V 240/15 EXT- Mineral wool 

A15 

Hybrid Acoustic roof system 120 - - EXT-B PIR* / Mineral 460a/24 

wool 

Hybrid Acoustic wall system 100 V 240/15 EXT- 

A15 

PIR* / Mineral 

wool 

Trisomet 333 (roof and wall 40, 60, 80, 100 and H or V - EXT-B PIR* 460a/26 

panel) 

120 

Trisomet 333 (wall panel) 60, 80, 100 and 120 V 240/25 EXT- 

A15 

PIR* 460a/27 

Cert. 

No. 

Notes: 


2. The PIR core materials marked * are both CFC and HCFC Free and are stated to be Low Global Warming Potential (GWP). 

3. LPCB Ref 460a/13, Trimapanel wall panels having a grade EXT-A are to be stitched on the internal face with SFS Intec IR2 - 4.8 x 60 

(70mm thick panel), or SFS Intec IR2 - 4.8 x 80 (90mm thick panel) screws or similar at maximum 250mm centres. 

4. LPCB Ref 460a/19 Trinsul wall system outer liner 0.55mm steel stitched at minimum 600mm centres, internal liner 0.4mm steel. 

5. LPCB Ref 460a/20 Structural Liner Tray system requires the liner tray joints to be stitched at minimum 450mm centres. 

6. LPCB Ref 460a/21 Structural Flat Metal roof deck steel profile liner D19 - D35 require no side lap stitching, steel profile liner D46 - 

D159 require side lap stitching min. 450mm c/c and steel profile liner D210 require side lap stitching min 350mm c/c. 

7. LPCB Ref 460a/26 Trisomet 333 wall panels can be laid with the long joints in the vertical orientation stitched or unstitched, or in the 

horizontal orientation with the overlap joint stitched at maximum 600mm centres. 

8. LPCB Ref 460a/26 Trisomet 333 roof panels are to be secured to each purlin with 3 fixings, the perimeter of the roof system is to be 

secured to the frame support through the panel edge at 300mm centres. 

9. LPCB Ref 460a/27 Trisomet 333 wall panels are to be stitched at maximum 300mm centres with SL2-T-A14-4.8x20 self tapping steel 

screws or similar. 

20 Nov 2011 19



Eurobond Laminates Limited & Eurobond Doors Limited 

Wentloog Corporate Park, Wentloog, Cardiff CF3 2ER, United Kingdom 

Tel: + 44 (0)2920 776677 • Fax: + 44 (0)2920 369161 

E-mail: sales@eurobond.co.uk • Website: www.eurobond.co.uk 

Product Name 

Europanel Extra 

(wall panel) 

Europanel Lite (wall 

panel) 

Europanel Premier 

(wall panel) 

Rockspan Extra 

(wall panel) 

Rockspan Lite (wall 

panel) 

Thickness 

(mm) 

Wall Panel 

Orientation 

(V/H)* 



(minutes) 

LPS1181-1 

Grade 

Core 

Material 

75 V or H 60/60 EXT-A60 Mineral 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

75, 100, 125, V or H - EXT-B Mineral 

150, 175 & 200 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


150, 175 & 200 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


150, 175 & 200 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


150, 175 & 200 

fibre 


fibre 

Cert. 

No. 

545b/01 

545b/03 

545b/04 

545b/05 

545b/06 

20 20 Nov 2011



Product Name 

Rockspan Ultima 

(wall panel) 

Rainspan - Argeton 

terracotta tile 

system 

Rainspan - Linear 

system 

Rainspan - Parklex 

timber veneer 

system 

Rainspan - 

Rockpanel system 

Rainspan - Corium 

brick slip system 

Rainspan - Generic 

timber system 

Rainspan - Clicktile 

system 

Thickness 

(mm) 

Wall Panel 

Orientation 

(V/H)* 



(minutes) 

LPS1181-1 

Grade 

Core 

Material 


fibre 


fibre 

150 V or H 120/90 EXt-A90 Mineral 

fibre 


fibre 


fibre 

75, 100, 125, 

150, 175 & 

V or H - EXT-B Mineral 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545b/07 

545b/08 

545b/09 

545b/10 

545b/11 

545b/12 

545b/13 

545b/14 

Notes: 

1. LPCB Ref No. 545b/07 - 150mm and 175mm Rockspan Ultima wall panel joints are to be stitched on both internal and external faces 

using 4.7mm diameter x 20mm long self-tapping screws at 300mm centres, the 200mm panel does not require stitching. 

2. LPCB Ref No. 545b/13 to 545b/19, the thickness specified relates to the insulated panel thickness only and does not include the 

facade system depth. 

* Wall panel orientation, Vertical or Horizontal (V/H), relates to the long joint orientation of the insulated panel. 

20 Nov 2011 21



Euroclad Limited 

Wentloog Corporate Park, Wentloog Road, Cardiff CF3 2ER, United Kingdom 

Tel: +44 (0)2920 790722 • Fax: +44 (0)2920 793149 

E-mail: sales@euroclad.com • Website: www.euroclad.com 

Certificate No: 879a to LPS1181: Part 1 

Product Name 

Elite 1 (Roof 

System) 

Elite 2 (Roof 

System) 

Elite 3 (Roof 

System) 

Elite 4 (Roof 

System) 

Elite 51 (wall 

system) 


system) 


system) 


system) 


system) 


system) 


system) 


system) 


system) 

System 

Specification 

Thickness 

(mm) 

Wall panel 

orientation 

(H/V) 

Fire Resisitance 

(minutes) 


Grade 

Core 

material 

203 - 252 - -/- EXT-B Glass Wool or Mineral 

Wool 

879a/05 

218 - 312 - -/- EXT-B Glass Wool or Mineral 879a/06 

Wool 


Wool 


Wool 

153 - 173 V -/- EXT-B Glass Wool or Mineral 879a/09 

Wool 

153 - 173 V 240 / 15 EXT-A15 Glass Wool or Mineral 

Wool 

153 - 173 V 240 / 30 EXT-A30 (note Mineral Wool 

4) 


Wool 


Wool 


4) 

160 V -/- EXT-B Glass Wool or Mineral 879a/11 

Wool 

160 V 240 / 15 EXT-A15 Glass Wool or Mineral 

Wool 

160 V 240 / 30 EXT-A30 (note Mineral Wool 

4) 


Wool 


Wool 


4) 

180 H -/- EXT-B Glass Wool or Mineral 879a/13 

Wool 

180 H 240 / 15 EXT-A15 Glass Wool or Mineral 

Wool 

180 H 240 / 30 EXT-A30 (note Mineral Wool 

4) 

181 H -/- EXT-B Glass Wool or Mineral 879a/14 


Wool 

181 H 240 / 30 EXT-A30 (note 

4) 

Mineral Wool 

168 H -/- EXT-B Glass Wool or Mineral 

Wool 


4) 


Wool 


Wool 


Wool 


4) 


Wool 

Cert. 

No. 

879a/15 

879a/16 

879a/17 

22 20 Nov 2011



Product Name 

System 

Specification 

Thickness 

(mm) 

Wall panel 

orientation 

(H/V) 

Fire Resisitance 

(minutes) 


Grade 

Core 

material 


Wool 

200 H 240 / 30 EXT-A30 (note 

4) 

Mineral Wool 

Cert. 

No. 

Notes: 

1. Where Elite wall systems are required to achieve grade EXT-A15, the internal liner sheet side lap joints must be stitched using steel 

rivets at 450mm centres. For grade EXT-A30 the internal liner sheet side lap joints must be stitched at 300mm centres. 

2. Stitching can be removed from the EXT-A15 wall systems providing that the maximum spacing between sheeting rails is reduced to 

1.5m and the internal liner is either Euroclad 1000/32 or MW5 profiles. 

3. For wall systems the sheeting rail spacing shall be a maximum of 2m for EXT-B, EXT-A15 & EXT-A30, the external liner must be 

fixed to the channels of the spacer system using self-drilling, self-tapping screws at nominal 400mm centres for all grades. 

4. For grade EXT-A30 systems The minimum permissible stone mineral wool thickness is 180mm, or for systems with horizontally laid 

external weather sheets where the eurobar spacer rails are vertical and the insulation in the core is supported by additional steel Z- 

section supports, and with a minimum density of the insulation of 33kg/m³ the minimum insulation thickness can be reduced to 

150mm. 

5. For Elite roof systems 1 - 4 the maximum purlin spacing is 1.8m. 

6. Please refer to BRE Assessment Report CC248407 for approved alternative spacer systems, internal & external profiles, internal & 

external profile coatings and insulation cores for the Elite systems 1, 2, 3, 4, 51, 52, 53, 54, 55, 56, 57, 58 & 60. 

Hemsec Manufacturing Limited 

Stoney Lane, Rainhill, Prescot, Merseyside L35 9LL, United Kingdom 

Tel: +44 (0)151 426 7171 • Fax: +44 (0)151 493 1331 

E-mail: sales@hemsec.com • Website: www.hemsec.com 

Certificate No: 558b to LPS 1181: Part 1: Issue 1 

Product Name 

Specification 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

Longclad LC1150 Wall (wall panels) 50mm to 175mm - - EXT-B PIR 558b/01 

Longdeck LD1150 Wall (roof 50mm to 175mm - - EXT-B PIR 558b/02 

panels) 

Longclad LC1150 Wall (wall panels) 100mm to 

60 30 EXT-A30 PIR 558b/03 

175mm 

Longdeck LD1150 Wall (roof 125mm to 

52 40 EXT-A30 PIR 558b/04 

panels) 

175mm 

SIP Firecheck wall system 160 to 287 75 75 EXT- PUR 558b/05 

A60 

257.5 to 329.5 101 101 EXT-A90 PUR 558b/06 

Notes: 

1. Longclad LC1150 Wall panels LPCB Ref. No. 558b/01 & 558b/03 can be installed with the long joints in the vertical or horizontal 

orientation. 

2. The joints of the Longclad LC1150 wall panel’s 558b/01 should be stitched at 150mm centres on the internal face. 

3. The joints of the Longdeck LD1150 roof panel’s 558b/02 should be stitched at 150mm centres on the internal face. 

4. The joints of the Longclad LC1150 wall panel’s 558b/03 should be stitched at 150mm centres on the internal and external face. 

When installed the supporting framework shall provide support at a maximum of 4m centres both horizontally & vertically. 

5. The joints of the Longdeck LD1150 roof panel’s 558b/04 should be stitched at 150mm centres on the internal and external face. 

6. LPCB Ref 558b/05 - SIP Firecheck wall system was tested and is approved to LPS 1181-1 as a non load-bearing, non structural builtup 

wall system of the following configuration; Rigid polyurethane foam core (95mm to 222mm thick) sandwiched between 15 mm 

orientated strand boards (Krono OSB-3), the panel size was 1.2m x 3.0m and installed with 3 metre joints vertical. The system was 

clad on the fire exposed face with two layers of British Gypsum wall boards; A single layer of ‘Gyproc’ 12.5mm wall board (outer layer) 

and a single layer of ‘Gyproc Fireline’ 12.5mm board (inner layer), wall board layer joints were staggered by 600mm and fixed to 

softwood timber battens positioned at 600mm centres with 3.5mm x 50mm dry wall screws at 300mm centres. The system was tested 

with Hemsec 175mm thick Longdeck LD1150 PIR core roof panels. 

7. LPCB Ref 558b/06 - SIP Firecheck wall system is approved to LPS 1181-1 as a non load-bearing, non structural built up wall system 

of the following configuration; Rigid polyurethane foam core (150mm to 222mm thick) sandwiched between 15 mm orientated strand 

boards (Krono OSB-3), the panel size is 1.2m x 3.0m and installed with 3 metre joints vertical and consisting of 148mm deep x 70mm 

thick x 3000mm long timber spline joints inserted into 35mm pre-formed rebates in the core insulation, the joints are fixed with 

adhesive and nail fixings at 100mm centres. The system is clad on the fire exposed face with two layers of British Gypsum wall 

boards; A single layer of ‘Gyproc’ 12.5mm wall board (outer layer) and a single layer of ‘Gyproc Fireline’ 15mm board (inner layer), 

20 Nov 2011 23



with the wall board joints between layers staggered by 600mm and fixed to softwood timber battens 50mm x 50mm spaced at 600mm 

centres with 3.5mm x 50mm dry wall screws at 300mm centres, the stud cavity is filled with Knauf Rocksilk Universal slab RW33 

insulation. 

ISOCAB France S.A. 

Avenue de la Gironde, Z.I. Petite Synthe, 59640 Dunkerque, France 

Tel: +33 328 29 26 30 • Fax: +33 328 60 11 93 

E-mail: info@isocabfrance.fr • Website: www.isocab.be 


Product Name 

Specification 

System Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

ISOCAB Industrial (wall and roof panel) 40 - 200 - - EXT-B PIR 465a/01 

Notes: 

1. Wall panels are laid vertically. 

2. Both wall and roof panels require internal stitching at 300mm centres using 3.2mm diameter x 25mm screws and internal steel 

flashings 0.6mm thick x 120mm wide overlaying three beads of Lorient intumescent mastic, stitched at 150mm centres using 3.2mm 

diameter x 16mm screws. 

Kingspan Insulation Limited 

Pembridge, Leominster, Herefordshire HR6 9LA, United Kingdom 

Tel: +44 (0)1544 388601 • Fax: +44 (0)1544 388888 

E-mail: info.uk@insulation.kingspan.com • Website: www.insulation.kingspan.com 

Certificate No: 388b to LPS 1181: Part 1 

Product Name 

Roofing systems incorporating Thermaroof TR26 

LPC/FM zero ODP Insulation (also available as 

Thermataper TT46 for cut-to-fall roofing systems) 

Roofing systems incorporating Thermaroof TR27 

LPC/FM zero ODP Insulation (also available as 

Thermataper TT47 for cut-to-fall roofing systems) 

Specification 

Thickness 

(system) 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

65 to 155 - - EXT- 

B 

65 to 155 - - EXT- 

B 

Core 

Material 

HCFCfree 

PIR 

HCFRfree 

PIR 

Cert. 

No. 

388b/01 

388b/02 

Notes: 

1. LPCB Ref 388b/01 Thermaroof TR26/ LPC/FM Mechanically Fixed Insulated metal deck system is approved to LPS 1181-1 as a built 

up roof system of the following configuration: 

Corus D35 Roof Decking (0.7mm thick) or equivalent; deck panel lap joints stitched at 400mm centres. 

With or without Corus Kalzip/Icopal Monofilament 250μm or equivalent approved Vapour Control Layer (VCL); loose laid on top of 

the deck. 

Kingspan TR26/TT46 LPC/FM foil faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 2.4m x 1.2m sheets 

(approved at 30mm to 120mm thick) the boards through fixed to deck using 140mm long SFS drill point roof fasteners at 3.8 

fixings per m² with a 70mm diameter metal plate washer. 

Weather sealed using Protan SE membrane (1.2mm x 1000mm) having a 120mm lap joint with a 40mm hot air weld, or 

equivalent woven polyester reinforced PVC water proof membrane, mechanically fixed to the roof system using RP75 x 100mm 

telescopic tube washers and 4.8 x 60mm screw fixed to the metal deck at 150mm centres. The membrane must be restrained 

around the edges of the deck with an edge restraint bar stitched at 400mm centres. 

The roof system was tested in combination with LPCB approved PIR core wall panels. 

2. LPCB Ref 388b/02 Thermaroof TR27 LPC/FM Mechanically Fixed Insulated metal deck system is approved to LPS 1181-1 as a built 

up roof system of the following configuration: 

Corus D35 Roof Decking (0.7mm thick) or equivalent; deck panel lap joints stitched at 400mm centres. 

With or without Corus Kalzip/Icopal Monofilament 250μm or equivalent approved Vapour Control Layer (VCL); loose laid on top of 

the deck. 

24 20 Nov 2011



Kingspan TR27/TT47 LPC/FM glass tissue faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 2.4m x 1.2m 

sheets (approved at 30mm to 120mm thick) the boards through fixed to deck using 140mm long SFS drill point roof fasteners at 

3.8 fixings per m² with a 70mm diameter metal plate washer. 

Weather sealed using Protan SE membrane (1.2mm x 1000mm) having a 120mm lap joint with a 40mm hot air weld, or 

equivalent woven polyester reinforced PVC water proof membrane, mechanically fixed to the roof system using RP75 x 100mm 

telescopic tube washers and 4.8 x 60mm screw fixed to the metal deck at 150mm centres. The membrane must be restrained 

around the edges of the deck with an edge restraint bar stitched at 400mm centres. 

The roof system was tested in combination with LPCB approved PIR core wall panels. 

3. LPCB Ref. 388b/01 and 388b/02 certification is also valid for insulation boards manufactured at Kingspan Insulation Ltd, 

Castleblayney, County Monaghan, Ireland (LPCB FPC reference number 858). 

Kingspan Ltd 

Carrickmacross Road, Kingscourt, Co. Cavan, Ireland 

Tel: +353 42 969 8572 • Fax: +353 42 969 8576/77 

E-mail: info.irl@kingspanpanels.com • Website: www.kingspanpanels.com 

Certificate No: 186a to LPS 1181: Part 1: Issue 1.1 

Product Name 

Kingspan Benchmark 

Trespa System 

Kingspan KS1000 RW 

(roof and wall panel) 


(wall panel) 

Kingspan KS1000 

RW/FW30 (wall panel) 


(roof panel) 

Kingspan KS1000 SF 



(wall panel) 


SF/FW30 (wall panel) 

Kingspan KS1000 BU 


Kingspan KS1000 LJ 

(wall panel) 


(roof panel) 

Kingspan KS1000 TS 

(roof panel) 


(roof panel) 

Kingspan KS1000 RT 

Rooftile (roof panel) 

Kingspan KS500 Zip & 

KS1000 Zip (roof panel) 

Kingspan KS1000 LP 

(roof panel) 

Kingspan KS1000 CR 

(roof panel) 

Kingspan KS1000 DR 

(wall panel) 


(roof panel) 

Kingspan KS1000 TD 

(roof panel) 

BenchmarkTopspan (roof 

panel) (roof panel) 

Specification 

Thickness 

(mm) 

Specification 

Wall panel 

orientation 

(H/V) 

(note 1) 

Specification 

Kingspan 

Model 

Specification 

Ref. (note 2) 



(minutes) 

LPS 

1181- 

1 

Grade 

Core 

Material 

(note 3) 

95 - 150 V or H 31 Rev 1 - EXT-B Ecosafe 

PIR 

260a/70 

30 - 120 V or H 17 Rev 6 - EXT-B Ecosafe 186a/42 

PIR 

40 - 120 V 17 Rev 6 144 / 18 EXT- Ecosafe 186a/38 

A15 PIR 

100 & 120 V 17 Rev 6 241 / 43 EXT- Ecosafe 186a/40 

A30 PIR 

30 - 120 - 27 Rev 2 - EXT-B Ecosafe 260a/69 

PIR 


PIR 


A15 PIR 


A30 PIR 

30 - 120 V 5 Rev 5 - EXT-B Ecosafe 186a/46 

PIR 


PIR 


PIR 

30 - 120 - 12 Rev 3 - EXT-B Ecoafe 186a/47 

PIR 


PIR 

45 - 100 - 10 Rev 3 - EXT-B PIR 279a/10 

Cert. 

No. 

45 - 124 - 8 Rev 8 - EXT-B Ecosafe 

PIR 

260a/54 


PIR 


PIR 

40 - 100 V 29 Rev 0 - EXT-B PIR 279a/16 

80 - 100 V 29 Rev 0 69 / 23 EXT- 

A15 

PIR 279a/17 


PIR 

34, 46, 68, 80, - 30 Rev 1 - EXT-B Ecosafe 279a/29 

100 & 120 

PIR 

66 - 15 Rev 4 - EXT-B PIR 279a/31 

20 Nov 2011 25



Product Name 

Kingspan KS600 - 1200 

MR, FL, FL-S, EB, WV, 

MM, CX , PL, Benchmark 

Evolution & KS1000 TL, 

Benchmark Louvre DW & 

Benchmark Curve DW 

(wall panel) 



MM, CX, PL, Benchmark 

Evolution & KS1000 TL 

(wall panel) 


LS (wall panel) 

Kingspan KS600 - 1000, 

Benchmark Render DW 

(wall panel) 


FX (wall panel) 

Kingspan KS1000 EP 

Energi (wall and roof 

panel) 

Kingspan KS1000 FC 

(wall and roof panel ) 


(wall and roof panel) 


(wall panel) 


(wall panel) 


Metallic ACM Tray 


Wood Composite System 


Ceramic Granite System 

Thermabrick Façade 

system 


Ceramic Tile System 

Kingspan KS1100 CS 

(wall panel) 



Specification 

Thickness 

(mm) 

Specification 

Wall panel 

orientation 

(H/V) 

(note 1) 

Specification 

Kingspan 

Model 

Specification 

Ref. (note 2) 



(minutes) 

LPS 

1181- 

1 

Grade 

Core 

Material 

(note 3) 


PIR 

70 - 140 V 18 Rev 8 40 / 15 EXT- 

A15 

Ecosafe 

PIR 

100 - 140 V 18 rev 8 132 / 28 EXT- 

A30 

Ecosafe 

PIR 

80 - 140 H 9 Rev 5 - EXT-B Ecosafe 

PIR 


PIR 

70 - 100 V 20 Rev 2 40 / 15 EXT- 

A15 

Ecosafe 

PIR 


PIR 

68 - 100 V 25 Rev 0 - EXT-B Ecosafe 

PIR 

Cert. 

No. 

260a/37 

260a/36 

260a/64 

260a/67 

260a/49 

260a/50 

260a/53 

279a/30 


PIR 

279a/32 

34 - 100 V or H 16 Rev 3 - EXT - PIR 279a/19 

B 

68 - 100 V 16 Rev 3 34 / 15 EXT- PIR 279a/21 

A15 

100 V 16 Rev 3 79 / 34 EXT- PIR 279a/28 

A30 


PIR 


PIR 


PIR 


A30 PIR 


PIR 


A60 PIR 


PIR 


A30 PIR 

80 - 200 V 13 Rev 2 - EXT - Ecosafe 279c/15 

B PIR 

80 - 200 - 13 Rev 2 - EXT-B Ecosafe 279c/16 

PIR 

Notes: 


2. The Kingspan Model Specification documents contain full system details including panel fixing requirements, joint seals and stitching 

details as applicable, reference must be made to the appropriate Model Specification to define the specific approved installation 

requirements. Copies of Model Specification’s are available on request, Please contact the Kingspan Envirocare Department. 

3. Core material solutions listed as Ecosafe PIR are CFC/HCFC/HFC Free, Low GWP. Core material solutions listed as PIR are 

CFC/HCFC Free. 

26 20 Nov 2011



Kingspan Ltd. 

Greenfield Business Park No. 2, Greenfield, Holywell, Flintshire CH8 7HU, United Kingdom 

Tel: +44 (0)1352 716100 • Fax: +44 (0)1352 716161 

E-mail: info@kingspanpanels.com • Website: www.kingspanpanels.com 


Product Name 


Trespa System 




(wall panel) 


RW/FW30 (wall panel) 


(roof panel) 




(wall panel) 


SF/FW30 (wall panel) 

Kingspan KS1000 BU 



(wall panel) 


(roof panel) 


(roof panel) 


(roof panel) 

Kingspan KS1000 RT 

Rooftile (roof panel) 

Kingspan KS500 Zip & 

KS1000 Zip (roof panel) 

Kingspan KS1000 LP 

(roof panel) 

Kingspan KS1000 CR 

(roof panel) 


(wall panel) 


(roof panel) 

Kingspan KS1000 TD 

(roof panel) 


Topspan (roof panel) 

Kingspan KS600 -1200 


MM, CX , PL, 

Benchmark Evolution, 

KS1000 TL, Benchmark 

Louvre DW & 

Benchmark Curve DW 

(wall panel) 



MM, CX, PL, 

Benchmark Evolution & 

KS1000 TL (wall panel) 

Specification 

Thickness 

(mm) 

Specification 

Wall Panel 

Orientation 

(H/V) 

(note 1) 

Specification 

Kingspan 

Model 

Specification 

Ref. (note 2) 



(minutes) 

LPS 

1181 - 

1 

Grade 

Core 

Material 

(note 3) 


PIR 

260a/70 


PIR 


A15 PIR 

100 & 120 V 17 Rev 6 241 / 43 EXT- Ecosafe 260a/40 

A30 PIR 


PIR 


PIR 


A15 PIR 

120 V 19 Rev 4 241 / 43 EXT- Ecosafe 260a/41 

A30 PIR 


PIR 


PIR 


PIR 


PIR 


PIR 

45 -100 - 10 Rev 3 - EXT-B PIR 279a/10 

45 -124 - 8 Rev 8 - EXT-B Ecosafe 

PIR 

260a/54 


PIR 


PIR 

40 - 100 V 29 Rev 0 - EXT-B PIR 279a/19 

80 - 100 V 29 Rev 0 69 / 23 EXT- 

A15 

PIR 279a/17 


PIR 

34, 46, 68, 80, - 30 Rev 1 - EXT-B Ecosafe 279a/29 

100 & 120 

PIR 

66 - 15 Rev 4 - EXT-B PIR 279a/31 


PIR 

70 - 140 V 18 Rev 8 40 / 15 EXT- 

A15 

Ecosafe 

PIR 

Cert. 

No. 

260a/37 

260a/36 

20 Nov 2011 27



Product Name 


LS (wall panel) 

Kingspan KS600 - 1000, 

Benchmark Render DW 

(wall panel) 


FX (wall panel) 

Kingspan KS1000 EP 

Energi (wall and roof 

panel) 


(wall and roof panel ) 


(wall and roof panel) 


(wall panel) 


(wall panel) 


Metallic ACM Tray 


Wood Composite 

System 


Ceramic Granite System 

Thermabrick Façade 

system 


Ceramic Tile System 


(wall panel) 



Specification 

Thickness 

(mm) 

Specification 

Wall Panel 

Orientation 

(H/V) 

(note 1) 

Specification 

Kingspan 

Model 

Specification 

Ref. (note 2) 



(minutes) 

LPS 

1181 - 

1 

Grade 

Core 

Material 

(note 3) 

100 - 140 V 18 Rev 8 132 / 28 EXT- 

A30 

Ecosafe 

PIR 

80 - 140 H 9 Rev 5 - EXT-B Ecosafe 

PIR 


PIR 

Cert. 

No. 

260a/64 

260a/67 

260a/49 


A15 PIR 



PIR 

279a/30 


PIR 

34 - 100 V or H 16 Rev 3 - EXT-B PIR 279a/19 

68 - 100 V 16 Rev 3 34 / 15 EXT- 

A15 

PIR 279a/21 

100 V 16 Rev 3 79 / 34 EXT- PIR 279a/28 

A30 


PIR 


PIR 


PIR 

120 - 150 V 23 Rev 4 73 / 35 EXT- Ecosafe 

A30 PIR 


PIR 


A60 PIR 


PIR 


A30 PIR 


PIR 

80 - 200 - 13 Rev 2 - EXT-B Ecosafe 

PIR 

260a/58 

260a/63 

260a/60 

260a/61 

260a/35 

260a/34 

279c/15 

279c/16 

Notes: 


2. The Kingspan Model Specification documents contain full system details including panel fixing requirements, joint seals and stitching 

details as applicable, reference must be made to the appropriate Model Specification to define the specific approved installation 

requirements. Copies of Model Specifications are available on request. Please contact the Kingspan Envirocare Department. 

3. Core material solutions listed as Ecosafe PIR are CFC/HCFC/HFC Free, Low GWP. Core material solutions listed as PIR are 

CFC/HCFC Free. 

Modular Panel Systems Limited 

Mohill, Co.Leitrim, Ireland 

Tel: +353 719631162 • Fax: +353 719651979 

E-mail: info@modular.ie • Website: www.modular.ie 


Product Name 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

PIR ExoClad (wall and ceiling panel) 50 - - EXT-B PIR 750b/01 

28 20 Nov 2011



Product Name 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

PIR ExoClad (wall panel) 50 120 16 EXT-A15 PIR 750b/02 

Notes: 

1. The joints of the Exoclad panels 750b/01 should be stitched with 6.3mm x 22mm long self tapping screws @ 250mm centres on the 

external overlap and stitched with 4.8mm dia x 10mm stainless steel rivets @ 250mm centres on the internal face. 

2. Wall panels to be orientated vertically only. 

3. Exoclad wall panels 750b/02, panel joints external overlap stitched with stainless steel rivets and screwed at 100 mm centres. The 

internal joint is stitched at 100mm centres and protected with a 250mm wide by 50mm deep insulated cover strip stitched at 100mm 

centres. 

N.V. Joris IDE 

Hille 174, B-8750, Zwevezele, Belgium 

Tel: +44 (0)1928 571 444 • Fax: +44 (0)1928 571 488 

E-mail: division.export@joriside.co.uk • Website: www.joriside.co.uk 


Tel: +44 (0)1928 571 444 • Fax: +44 (0)1928 571 488 

E-mail: sales@joriside.co.uk • Website: www.joriside.co.uk 

Certificate No: 700a to LPS1181: Part 1: Issue 1 

Product Name 

Specification 

System 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Isotherm Built up system (wall panels) 200 - - EXT-B Glass 700a/06 

mineral wool 

Isotherm Built up system (roof panels) 220 - - EXT-B Glass 700a/07 

mineral wool 

JI ROOF 1+2 1000 (roof and wall panels) 30 - 120 - - EXT-B PIR 700a/09 

JI ROOF 1+2 1000 (wall panel) 60 - 120 67 17 EXT- PIR 700a/10 

A15 

JI ROOF 1+2 1000 with Tile System (roof 100 - 120 - - EXT-B PIR 700a/11 

panels) 

JI WALL SF 1060/1000/900/600 (wall 60 - 120 - - EXT-B PIR 700a/12 

panels) 

JI WALL SF 1060/1000/900/600 (wall 60 - 120 61 20 EXT- PIR 700a/13 

panels -vertical orientation only) 

A15 

JI WALL SF 1060/1000/900/600 (wall 60 - 120 30 15 EXT- PIR 700a/14 

panels) 

A15 

JI PERMAPAN 1100 (roof panels) 40-100 - - EXT-B PIR 700a/15 

Cert. 

No. 

Notes: 

1. LPCB Ref. No. 700a/06 internal linings to be horizontal and external linings to be vertical 

2. LPCB Ref. No. 700a/09 roof and wall panels fixed through every valley with 5.5mm self drilling/tapping screws into the roof and wall 

rail locations. Roof panel overlaps between adjoining panels shall be stitched at 300mm centres with 4.8mm self drilling/tapping 

screws or equivalent. 

3. LPCB Ref. No. 700a/09 wall panels can be laid with the long joints in the vertical or horizontal orientation. 

4. LPCB Ref. No. 700a/10 wall panels to be laid with the long joints in the horizontal orientation only. The panels were fixed through 

every valley with 5.5mm self drilling/tapping screws into the wall rail locations. The panel overlaps between panel joints were stitched 

at 250mm centres with 4.8mm self drilling/tapping screws. Maximum unsupported span between rails 1760mm. 

5. LPCB Ref. No. 700a/11 roof panels fixed through every valley with 5.5mm self drilling/tapping screws into the roof rail locations. The 

panel overlaps between panel joints were stitched at 300mm centres with 4.8mm self drilling/tapping screws. The tile system 

comprised of timber battens 50mm x 25mm fixed to the crown of every profile overlayed with single roman clay tiles with a maximum 

load of 42kg/m2. 

6. LPCB Ref. No. 700a/12 wall panels can be laid with the long joints in the vertical or horizontal orientation. 

7. LPCB Ref. No. 700a/13 wall panels to be laid with the long joints in the vertical orientation only, the panel joints shall be stitched on 

the fire side with 5.5mm x 50mm self tapping screws at maximum centres of 100mm. 

8. LPCB Ref. No. 700a/14 wall panels can be laid with the long joints in the vertical or horizontal orientation, the panel joints shall be 

stitched on the fire side with 5.5mm x 50mm self tapping screws at maximum centres of 100mm. 

9. LPCB Ref. No 700a/15. Roof panel overlaps between adjoining panels shall be stitched at 300mm centres with 4.8mm self 

drilling/tapping screws or equivalent. 

20 Nov 2011 29



Quinn Therm Limited 

Scotchtown, Ballyconnell, Co. Cavan, Ireland 

Tel: +353 49 952 5604 • Fax: +353 49 952 5601 

E-mail: info@quinn-therm.com • Website: www.quinn-therm.com 

Certificate No: 893a to LPS1181: Part 1 

Product Name 

QRFR Fully adhered Insulating metal 

deck roof system 

QRFR Mechanically Fixed metal deck 

roof system 

Specification 

Thickness 

(mm) 


(min) 

Integrity 


(min) 

Insulation 

Grade 

85 - 185 - - EXT- 

B 

85 - 185 - - EXT- 

B 

Core 

Material 

Cert. 

No. 

PIR 893a/01 

PIR 893a/02 

Notes: 

1. LPCB Ref 893a/01 QRFR Fully adhered Insulating metal deck roof system is approved to LPS 1181-1 as a built-up roof system of the 

following configuration: 

• Steadmans AS34 single skin roof profile deck (0.7mm thick); deck panel lap joints stitched at 250mm centres. 

• Multilfold 250µm Vapour Control Layer (VCL) laid on top of the deck, with the VCL cut back to within 75mm from the edge of the 

deck perimeter and further protected by flashing installed to form an ‘upstand’ around the perimeter of the roof system. 

• 150mm thick Quinntherm QRFR glass fibre tissue faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 2.4m x 

1.2m sheets (tested at 150mm thick, but available and approved between 50mm to 150mm thick), the boards being through fixed 

to the steelwork using 6.3 x 175mm fastec CR10 fluro carbon coated screws, with discs, at six fixings per m2 

• Weather sealed using a Sika-Trocal SGK 1.5 (1.5mm x 1100mm) water proof membrane adhered to the Quinntherm Insulation 

using Sika-Trocal C300 adhesive at a rate of 250 g/m². 

• The 150mm insulation roof system tested incorporated a 150 x 200mm external edge flashing and a 300 x 300mm internal 

roof/wall 1.6mm galvanised steel flashing. 

• The roof system was tested in combination with LPCB approved PIR core wall panels. 

2. LPCB Ref 893a/02 QRFR Mechanically fixed Insulating metal deck roof system is approved to LPS 1181-1 as a built-up roof system 

of the following configuration: 

• Steadmans AS34 single skin roof profile deck (0.7mm thick); deck panel lap joints stitched at 300mm centres. 

• Multilfold 250µm Vapour Control Layer (VCL) laid on top of the deck, with the VCL cut back to within 75mm from the edge of the 

deck perimeter and further protected by flashing installed to form an ‘upstand’ around the perimeter of the roof system. 

• 150mm thick Quinntherm QRFR foil faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 2.4m x 1.2m sheets 

(tested at 150mm thick, but available and approved between 50mm to 150mm thick), the boards being through fixed to the 

steelwork using 6.3 x 175mm fastec CR10 fluro carbon coated screws in a 500mm x 500mm square pattern. 

• Weather sealed using a Sika-Trocal Type S 1.5 (1.5mm x 1100mm) water proof membrane mechanically fixed to the roof system 

using Trocal Metal Discs and Fasteners secured in place by the 6.3 x 175mm fastec CR10 fluro carbon coated screws mentioned 

above. 

• The 150mm insulation roof system tested incorporated a 150 x 200mm external edge flashing and a 300 x 300mm internal 

roof/wall 1.6mm galvanised steel flashing. 

• The roof system was tested in combination with LPCB approved PIR core wall panels. 

Recticel Insulation Products / Recticel N.V 

Enterprise way, Meir Park, Stoke-On-Trent ST3 7UN, United Kingdom 

Tel: +44 (0)1782 590470 • Fax: +44(0)1782 590499 

E-mail: enquiries@recticelinsulation.co.uk • Website: www.recticelinsulation.com 

Recticel N.V 

Tramstraat 6, B-8560, Wevelgem, Belgium 

Certificate No: 968a to LPS 1181: Part 1: Issue 1 

30 20 Nov 2011



Product Name 

Roofing system incorporating Eurothane 

Silver 

Roofing system incorporating Powerdeck 

F 

Specification 

Thickness 

(System) 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

65 - 155 - - EXT- 

B 

65 - 155 - - EXT- 

B 

Core 

Material 

Cert. 

No. 

PIR 968a/01 

PIR 968a/02 

Notes: 

1. LPCB Ref 968a/01 Eurothane Silver Mechanically Fixed Insulated metal deck system is approved to LPS 1181-1 as a built up roof 

system of the following configuration: 

· Corus D35 Roof Decking (0.7mm thick) or equivalent; deck panel lap joints stitched at 400mm centres. 

· Eurothane Silver foil faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 2.4m x 1.2m sheets (approved at 

30mm to 120mm thick) the boards through fixed to deck using BS 4.8 x 130mm screws & SFS Isotak RP75 x 30 tube washers 

with a 183mm PVC disk sitting on top of the PIR insulation at 600mm centres 

· Weather sealed using Fatra Fatrafol 810AA (1.5mm x 1300mm) Single ply membrane having its lap joint’s hot air welded in 

accordance with manufacturer's recommendations, or equivalent single ply water proof membrane, the membrane is bonded to 

the 183mm PVC disks using Fatra FF855 adhesive, brush applied. 

· The roof system was tested in combination with LPCB approved PIR core wall panels. 

2. LPCB Ref 968a/02 Powerdeck F Mechanically Fixed Insulated metal deck system is approved to LPS 1181-1 as a built up roof 

system of the following configuration: 

· Corus D35 Roof Decking (0.7mm thick) or equivalent; deck panel lap joints stitched at 400mm centres. 

· Powerdeck F glass tissue faced Insulation layer of rigid polyisocyanurate (PIR) boards supplied in 1.2m x 0.6m sheets (approved 

at 30mm to 120mm thick) the boards through fixed to deck using BS 4.8 x 130mm screws & SFS Isotak RP75 x 30 tube washers 

with a 183mm PVC disk sitting on top of the PIR insulation at 600mm centres 

· Weather sealed using Fatra Fatrafol 810AA (1.5mm x 1300mm) Single ply membrane having its lap joint’s hot air welded in 

accordance with manufacturer's recommendations, or equivalent single ply water proof membrane, the membrane is bonded to 

the 183mm PVC disks using Fatra FF855 adhesive, brush applied. 

· The roof system was tested in combination with LPCB approved PIR core wall panels. 

Rockwool Limited 

Wern Tarw, Pencoed, Bridgend, Mid Glamorgan CF35 6NY, United Kingdom 

Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 

E-mail: info@rockwool.co.uk • Website: www.rockwool.co.uk 

Certificate No: 022g to LPS1181: Part 1: Issue 1.1 

Product Name 

Specification 

System 

Thickness 

(mm) (1) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

(2) 

Core 

Material 

Hardrock DD roof board system 210 120 120 EXT- Stone wool 022g/01 

A120 

100 - 135 60 60 EXT-A60 Stone wool 

100 - 210 - - EXT-B Stone wool 


Hardrock DD SPA roof board 

210 120 120 EXT- Stone wool 022g/02 

system 

A120 




DuoRock roof board system 100 - 210 60 60 EXT-A60 Stone wool 022g/03 


Cert. 

No. 

Notes: 

1. Roof board system LPCB Ref No. 022g/01 & LPCB Ref No. 022g/03: Mechanically fastened Sarnafil single ply type S327-12EL 

(1.2mm thickness), external weather proof membrane (or alternative membrane less than 3.5 kg/m² e.g. PVC, Chlorinated PE, Butyl 

Rubber with welded seams); 

Comprising of two layers of Rockwool roofing board with staggered joints (100mm minimum stagger for fire resistance up to 90 

minutes and 300mm stagger for 2 hours fire resistance), vapour control layer and 0.7mm thickness 35mm deep profile steel metal 

deck. 

Roof board system LPCB Ref No. 022g/02: Sarnafil single ply external weather proof membrane type G410-12EL (1.2mm thickness), 

fully adhered to Hardrock DD SPA roof board system with Sarnifil Adhesive(or Rockwool approved alternative adhesive/membrane 

combination, with a membrane material less than 3.5 kg/m² e.g. PVC, Chlorinated PE, Butyl Rubber with welded seams); comprising 

20 Nov 2011 31



of two layers of Rockwool roofing board with staggered joints (100mm minimum stagger for fire resistance up to 90 minutes and 

300mm stagger for 2 hours fire resistance), vapour control layer and 0.7mm thickness 35mm deep profile steel metal deck. 

Roof Board System LPCB Ref No 022g/01, 022g/02 & 022g/03 Hardrock DD, Hardrock DD SPA and DuoRock roofing boards are 

also available and approved in cut-to-fall tapered options, the relevant minimum & maximum system thickness and staggered joints 

shall apply as detailed above. 

2. For EXT-A fire resistance grading, the test construction was tested unloaded. However, deflection of the roof did not exceed the 

allowable limits set out in BS 476: Part 20: 1987 for loadbearing horizontal elements. 

3. Decking side laps were stitched at 450mm centres. The built up roofing system was tested with Eurobond Stone wool core sandwich 

wall panels. 

Ruukki Polska Sp. z.o.o 

ul Jaktorowska 13, 96-300, Zyradow, Poland 

Tel: 0121 704 7300 • Fax: 0121 711 9712 

E-mail: gareth.ellison@ruukki.com • Website: www.ruukki.com 

Certificate No: 1052a to LPS 1181-1 

Product 

Name 

SP2B UK 

(wall panel) 

SP2C UK 

(ceiling 

panel) 

SP2D UK 

(wall panel) 

SP2E UK 

(wall panel) 

Specification 


Wall panel 

orientation (H/V) 

(Note 1) 



(mins) 

LPS1181 - 

1 Grade 

Core 

Material 

Cert. No. 

100 H 61/34 EXT-A30 PIR 1052a/01 

100 V 61/30 EXT-A30 PIR 

40, 60, 80 and 100 H/V - EXT-B PIR 

80 and 100 H 53/17 EXT-A15 PIR 

120/80, 140/100 and 

- 63/37 EXT-A30 PIR 1052a/02 

210/170 

80/40, 100/60, 120/80, 

- - EXT-B PIR 

140/100 and 210/170 

80/40, 100/60, 120/80, 

140/100 and 210/170 

- 91/19 EXT-A15 PIR 

100 V 50/22 EXT-A15 PIR 1052a/03 

60, 80 and 100 H/V - EXT-B PIR 

120, 160, 180 and 200 H/V - EXT-B PIR 1052a/04 

120, 160, 180 and 200 V 46/25 EXT-A15 PIR 

Notes: 

1. Wall panel orientatin, Horizontal or Vertical (H/V), relates to the long joint orientation. 

2. LPCB Ref 1052a/02 EXT-B grade ceiling panels, joints shall be stitched on the external face using 4.9 x 19mm zinc coated 

carbon steel self drilling fasteners at nominal 300mm centres. 

3. LPCB Ref 1052a/02 EXT-A15 grade 80/40, 100/60, 120/80, 140/100 and 210/170 ceiling panels were fire resistance tested with 

an imposed load of 24kg/m2. The maximum unsupported span shall be limited to 2.0m between supports and the panel joints 

shall be stitched on the external face using 4.9 x 19mm zinc coated carbon steel self drilling fasteners at nominal 300mm centres. 

4. LPCB Ref 1052a/02 EXT-A30 grade 120/80, 140/100 and 210/170 ceiling panels were fire resistance tested with an imposed 

load of 32kg/m2. The maximum unsupported span shall be limited to 2.0m between supports and the panel joints shall be stitched 

on the external face using 4.9 x 19mm zinc coated carbon steel self drilling fasteners at nominal 300mm centres. 

SpeedDeck Building Systems Limited 

Oaksmere Business Park, Yaxley, Eye, Suffolk IP23 8BW, United Kingdom 

Tel: +44 (0)1379 788166 • Fax: +44 (0)1379 788161 

E-mail: speeddeck@eleco.com • Website: www.eleco.co/speeddeck 


Product Name 

SpeedDeck double skin roof 

system 

Specification 

System 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

180 - 220 - - EXT- 

B 

Core 

Material 

Cert. 

No. 

Glass wool 738a/01 

32 20 Nov 2011



Product Name 

Specification 

System 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

SpeedZip double skin roof system 180 - 220 - - EXT- 

B 

PP32 double skin roof system 180 - 220 - - EXT- 

B 

SpeedRoof double skin roof 180 - 220 - - EXTsystem 

B 

Core 

Material 

Cert. 

No. 




Notes: 

1. LPCB Ref. 738a/01 SpeedDeck double skin roof system: external sheet may be 0.9mm 3004 grade embossed plain aluminium or 

0.9mm aluminium coated with a 25 micron PVdF or 30 micron ARS paint finish or 0.6mm or 0.7mm steel with a 200 micron PVC paint 

finish i.e. Corus HPS200 or Dobel 200XT outer skin and Walkliner inner skin. 

2. LPCB Ref. 738a/02 SpeedZip double skin roof system: 0.9mm aluminium with a stucco plain or 25 micron PVdF or 30 micron 

ARS paint finish outer skin and Walkliner inner skin. 

3. LPCB Ref. 738a/03 PP32 double skin roof system: 0.7mm steel trapezoidal 32mm profile with a Dobel 200XT 200 micron PVC paint 

finish outer skin and Walkliner inner skin, outer skin lap joints stitched at 450mm centres. 

4. LPCB Ref. 738a/04 SpeedRoof double skin roof system: 0.7mm steel profile with Corus HPS200, Dobel 200XT or Dobel Nova outer 

skin finish and Walkliner inner skin. 

ThyssenKrupp Steel Europe AG 

Hammerstrasse 11, D-57223 Kreuztal, Germany 

Tel: +49 (0)2723 599 1221 • Fax: +49 (0)2723 599 1219 

E-mail: export@tks-bau.thyssenkrupp.com • Website: www.thyssenkrupp-bausysteme.com 

www.thyssenkrupp-steel-europe.com 


Product Name 

Specification 

Thickness 

(mm) 

Specification 

Wall Panel 

Orienation 

(H/V) 

(See Note 1) 


Integrity / 

Insualation 

LPS 1181- 

1 

Grade 

Core 

Material 

Hoesch isowand integral (wall 60 - 120 H/V - / - EXT-B PIR 657a/01 

panel) 

Hoesch isowand vario (wall panel) 60 - 140 H/V - / - EXT-B PIR 657a/02 

Hoesch isowelle (wall panel) 64 - 104 H/V - / - EXT-B PIR 657a/03 

Hoesch isorock integrad D (roof 95 - 155 - - / - EXT-B Mineral 657a/04 

panel) 

fibre 

Hoesch isowand vario (wall panel) 100 - 140 H 42 / 49 EXT-A30 PIR 657a/05 

80 - 140 H 32 / 24 EXT-A15 PIR 

80 - 140 V 61 / 26 EXT-A15 PIR 

Hoesch Thermodach (roof panel) 75 - 130 - - / - EXT-B PIR 657a/06 

Hoesch isodach integral (roof 75 - 155 - - / - EXT-B PIR 657a/07 

panel) 

Hoesch isodach mono (roof panel) 95 - 155 - - / - EXT-B PIR 657a/08 

Cert. 

No. 

Notes: 

1. Wall orientation, Horizontal or Vertical (H/V), relates to the long joint orientation. 

2. LPCB Ref. No 657a/04 - Roof panel joints are held by use of an aluminium locking system and covered with a continuous joint cover, 

cover ledge part No. S33-052. 

3. LPCB Ref. No. 657a/05 - Wall panels are stitched on the internal face using 5.5 x 70mm stainless steel screws at 150mm centres. 

4. LPCB Ref. No. 547a/05 Grade EXT-A15 Wall panel joints are stitched on the external face with 4.2mm self tapping stainless steel 

screws and nominal 400mm centres. 

5. LPCB Ref. No. 657a/06, 657a/07 and 657a/05 - Roof panel joints are stitched on the external face with 4.8mm self tapping stainless 

steel scres and nominal 900mm centres. 

6. LPBC Ref. No. 657a/07 and 657a/08 - Roof panel jonts are held by use of a locking system and covered with a continuous joint 

cover. 

20 Nov 2011 33



Trimo d.d 

Prijatljeva 12, 8210 Trebnje, Slovenija 

Tel: 00386 73460200 • Fax: 0038 673460127 

E-mail: trimo@trimo.si • Website: www.trimo.eu 

UK Supplier 

Trimo UK Ltd, Unit 4 Willaston House, Crewe Road, Nantwich, Cheshire CW5 6NE, United Kingdom 

Tel: +44 (0) 1270 665303 • Fax: +44 (0) 1270 664294 

E-mail: trimo@trimo.org.uk • Website: www.trimo.org.uk 


Product Name 

Specification 

System 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade Core Material Cert. No. 

Trimotherm FTV (wall panel) 100 - 150 95 95 EXT-A90 Mineral wool 650b/01 

Trimotherm SNV (ceiling panel) 100 98 95 EXT-A90 Mineral wool 650b/02 

Note: 

LPCB Ref. No. 650b/01 wall panels can be laid either horizontally or vertically. 

Xtratherm Limited 

Kells Road, Navan, Co. Meath, Ireland 

Tel: +353 46 906 6000 • Fax: +353 46 906 6090 

E-mail: info@xtratherm.com • Website: www.xtratherm.com 


Product Name 

XT/FR-Alu Roof 

system 

XT/TR-Alu roof 

System 

XT/FR-MG Roof 

System 

XT/TR-MG Roof 

System 

Specification 

System 

Thickness 

(mm) 


(minutes) 

Integrity 


(minutes) 

Insulation 

Grade 

66 - 136 - - EXT- 

B 

66 - 136 - - EXT- 

B 

66 - 136 - - EXT- 

B 

66 - 136 - - EXT- 

B 

Insulation 

Material 

Cert. 

No. 

PIR 851a/01 

PIR 

PIR 851a/02 

PIR 

Notes: 

1. LPCB Ref 851a/01, the built-up roof system tested and approved consists of; 

• PVC Membrane laid in lengths across the width of the roof, mechanically fixed with hot-air welded lap joints. 

• 100mm XT/SP XT/FR-Alu or XT/TR-Alu PIR insulation boards (available and approved between 30mm to 100mm thick) 

mechanically fixed using a minimum of 6 fasteners per 2.4m x 1.2m board; each fastener incorporated a 50mm x 50mm square 

plate spreader washer. Boards laid in a break bond pattern. 

• 1mm gauge Vapour Control Layer - loose lay. 

• 0.7mm gauge, 35mm deep profiled metal deck with overlap side laps stitched at 400mm centres. 

2. LPCB Ref 851a/02, the built-up roof system tested and approved consists of; 

• PVC Membrane laid in lengths across the width of the roof, solvent welded to the PIR insulation boards with HA-C membrane 

adhesive at a rate of 250g/m2 and with solvent welded lap joints. 

• 100mm XT/SP XT/FR-MG or XT/TR-MG PIR insulation boards (available and approved between 30mm to 100mm thick) 

mechanically fixed using a minimum of 6 fasteners per 2.4m x 1.2m board; each fastener incorporated a 50mm x 50mm square 

plate spreader washer. 

• 1mm gauge Vapour Control Layer- loose lay. 

• 0.7mm gauge, 35mm deep profiled metal deck with overlap side laps stitched at 400mm centres. 

34 20 Nov 2011



3. LPCB Ref 851a/01 & 851a/02, the built-up roof systems were tested and approved in combination with a 150mm mineral wool cored 

sandwich panel wall elements. 

20 Nov 2011 35


LPS 1181-2 SANDWICH PANELS OR BUILT-UP PANEL SYSTEMS USED INTERNALLY IN A BUILDING 

LPS 1181:Part 2 Requirements and tests for sandwich panels and built-up systems for use as internal 

constructions in buildings 

This standard determines the contribution to fire growth of sandwich panels and built-up cladding systems 

used internally within a building. Systems listed in this section are typically used for the construction of food 

factory clean rooms, cold store rooms/refrigerated spaces or room separation, other internal structure 

applications may also be applicable where insulated (acoustic or temperature controlled) spaces are 

specified. The structures are either self-supporting or supported by an external structure. 

The test is a large scale test comprising setting fire to an open-ended enclosure (approximately the size of a 

large domestic garage) from the sandwich panels or built-up cladding system. It evaluates the panels, the 

jointing methods and the supporting system including fixings, which gives an assessment of the true fire 

performance of the system which cannot be determined from traditional small scale reaction to fire tests, such 

as surface spread of flame or fire propagation tests. 

Products that have passed the test and have achieved LPCB approval are graded under the following 

designations: 

Requirements for internal applications 

GRADE 

Fire resistance 

Wall and ceiling lining test 

Thermal exposure 

Integrity (minutes) Insulation (minutes) Level Source 

INT-1 60 60 Enhanced Gas burner 

INT-2 30 30 Standard Timber crib 

INT-3 Standard Timber crib 

Brucha Ges.m.b.H 

Rusterstrasse 33, A-3451 Michelhausen, Michelhausen, Austria 

Tel: +43 (2275) 5878 1800 • Fax: +43 (2275) 5875 1804 

E-mail: office@brucha.at • Website: www.brucha.com 

Certificate No: 900b to LPS1181-2 

Product Name 

Specification 

Thickness 

(mm) 

WP-F (wall panel) 60, 80, 100, 

120, 150 & 

200 

WP-F (ceiling 

panel) 

60, 80, 100, 

120, 150 & 

200 

Maximum 

Unsupported 

Panel Span 

(m) 

Fire 

Resistance 

(min) Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. 

No. 

3.0 - - INT-3 Mineral Wool 900b/01 

3.5 - - INT-3 Mineral Wool 900b/02 

Notes: 

1. LPCB ref 900b/01 WP-F Wall panels to be installed with no external supports & the long edge joint in the vertical orientation only. 

2. LPCB ref 900b/01 & 900b/02 Wall and ceiling panel joints to be stitched on the internal face with 3.2 mm blind rivets at nominally 

300mm centres. 

3. LPCB ref 900b/02 WP-F Ceiling panels are supported by a hanger system consisting of. 

· A length of wire rope (4.0mm 6 x 7N 1AX) passed over and supported from a suitable load bearing frame. 

· An M10 turnbuckle with the rope secured using a ‘U bolt and clamp. 

· A length of M10 studding is passing through a hole which is drilled in the panel and secured on the internal surface with an 80mm 

diameter washer and domed head nut, this is further protected with a 0.55mm thick steel box (130mm-square x 30mm-deep with 

130mm x 30mm-flanges), lined with Promatect board and fixed using 3.2mm blind rivets. 

· The turn buckle is then adjusted to accommodate the weight of the panels. 

36 20 Nov 2011





Tel: + 44 (0)2920 776677 • Fax: + 44 (0)2920 369161 


Certificate No: 545c to LPS1181: Part 2: Issue 2 

Product Name 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

Panel Length 

(m) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

Cert. No. 

Firemaster Wall Lite 75 3.00 30 30 INT-2 Mineral fibre 545c/01 

75 3.00 60 30 INT-2 Mineral fibre 


















Firemaster Wall Extra 75 3.00 30 30 INT-2 Mineral fibre 545c/02 















Firemaster Ceiling Panel 75 6.00 - - INT-3 Mineral fibre 545c/03 


100 6.00 - - INT-3 Mineral fibre 





Firemaster Wall Ultima 150 7.50 240 240 INT-1 Mineral fibre 545c/05 



Notes: 

1. Grade INT-1 approved products have equal performance at Grade INT-2 and INT-3 

2. Grade INT-2 approved products have equal performance at Grade INT-3 

3. LPCB Ref No. 545c/02 - Where Eurobond 120 rock fibre insulation core is used in the 100mm thick panel the fire resistance insulation 

performance is limited to 90 minutes for maximum unsupported panel lengths of 5.5m 

4. LPCB Ref No. 545c/05 - 150mm and 175mm Firemaster Wall Ultima panel joints are to be stitched on both internal and external 

faces using 4.7mm diameter x 20mm long self-tapping screws at 300mm centres, the 200mm panel does not require stitching 

20 Nov 2011 37



Excel Industries Ltd 

Maerdy Industrial Estate (South), Rhymney, Gwent NP22 5PY, United Kingdom 

Tel: +44 (0)1685 845200 • Fax: +44 (0)1685 844106 

E-mail: info@excelfibre.com • Website: www.excelfibre.com 


Product Name 

Warmcel built-up wall 

panel system 

Warmcel built-up ceiling 

panel system 

Specification 

Thickness 

(mm) 

System 

thickness - 

293 (note 1) 

System 

thickness - 

329.2 (note 2) 

Maximum 

Unsupported 

Panel Length 

Self 

supporting 

system on 

fixed footplate 

(note 3) 

Supported on 

wall panel 

system (note 

4) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Core 

Material 

- - INT-3 Warmcel 

500 

cellulose 

fibre 

- - INT-3 Warmcel 

500 

cellulose 

fibre 

Cert. 

No. 

721a/01 

721a/02 

Notes: 

1. LPCB Ref. No. 721a/01 wall panel build specification 

Inner layer - 2 off layers (staggered joints) 10mm Sasmox Fire resistant & acoustic panel 

Core - 245mm void created by timber I beams at a maximum of 600mm centres, void filled with 

Warmcel 500 full fill insulation dry fill at 45-55kg/m 3 density 

Outer layer - 2 off layers (staggered joints) 10mm Sasmox Fire resistant & acoustic panel 

Alternative panel types for outer and inner layers - two layers of 10mm Xella Fermacell or 12.5mm Gyproc Fireline wallboard or 

12.5mm Lafarge Firecheck wallboard 

2. LPCB Ref. No. 721a/02 ceiling panel build specification 

Inner layer - 2 off layers (staggered joints) 10mm Sasmox Fire resistant & acoustic panel 

Core - 300mm void created by timber I beams at a maximum of 600mm centres, void filled with Warmcel 500 full fill insulation dry fill 

at 45-55kg/m 3 density 

Outer layer - single layer 9.2mm panel vent board 

Alternative panel types for inner layers - two layers of 10mm Xella Fermacell or 12.5mm Gyproc Fireline wallboard or 12.5mm Lafarge 

Firecheck wallboard 

3. No external supports for wall panel system used during test, maximum spans used during test, 10 metre long x 3 metre high. 

4. Ceiling panel system supported around perimeter on wall panel system only, no additional external supports used. Maximum spans 

used during test, 10 metre long x 4.5 metre wide. 

Paneltex Limited 

Kingston International Business Park, Somerden Road, Kingston-upon-Hull HU9 5PE, United Kingdom 

Tel: 01482 787236 • Fax: 01482 787238 

E-mail: sales@paneltex.co.uk • Website: www.paneltex.co.uk 

Certificate No: 993a to LPS 1181 Part 2: Issue 2.0 

Product Name 

Paneltex Fireproof 

Coldstore (wall and 

ceiling panel system) 

Specification Maximum Fire resistance (minutes) Grade Core Cert. 

Thickness (mm) system size Integrity/Insulation 

Material No. 

165 See Note 2 - / - INT-3 PIR 993a/01 

Notes: 

1. LPCB Ref 993a/01 Paneltex Fireproof Coldstore wall and ceiling panel systems to be installed with no external supports, the wall 

panels have the long edge joint in the horizontal orientation. 

2. LPCB Ref 993a/01 The maximum internal length and width of the Paneltex Fireproof Coldstore system shall not exceed 14.277m x 

3.584m. 

38 20 Nov 2011



Trimo d.d 


Tel: 00386 73460200 • Fax: 0038 673460127 


UK Supplier 


Tel: +44 (0) 1270 665303 • Fax: +44 (0) 1270 664294 


Certificate No: 650c to LPS 1181: Part 2: Issue 2 

Product Name 

Trimotherm 

FTV (wall 

panel) 

Specification 

Thickness 

(mm) 

Specification 

Orientation 

of 

Long Edges 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 

100 Horizontal 30 30 7.25 INT-2 Mineral 

wool 


wool 


wool 

100 Vertical 30 30 7.25 INT-2 Mineral 

wool 


wool 


wool 

120 Horizontal 30 30 8.00* INT-2 Mineral 

wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 

Cert. 

No. 

650c/01 

20 Nov 2011 39



Note: 

1. LPCB Ref. No. 6"50c/01 - unsupported spans marked *, span can be extended to 10.4m in respect of the length of the panel in 

horizontal laid orientation only. 

40 20 Nov 2011


LPS 1181-3 (DRAFT) CLADDING USED IN POD CONSTRUCTION 

LPS 1181: Part 3 (Draft) Requirements and tests for factory produced room modules (PODS) and building 

system modules 

‘PODS’ are prefabricated units forming a room containing all structural elements and linings and may include 

services and fittings. This section covers PODS constructed of sandwich panels walls and/or ceilings. 

For units listed in this section, the wall and ceiling construction has been tested to LPS 1181:Part 3 (Draft). 

The testing does not assess the structural performance of the POD under test nor the effect of doors or 

windows within the structure. 

Portakabin Ltd 

New lane, Huntington, , York YO32 9PT, United Kingdom 

Tel: 01904 611655 • Fax: 01904 611644 

E-mail: sales@portakabin.co.uk • Website: www.portakabin.co.uk 

Certificate No: 592a(2) to LPS1181 Part 3 

Product Name 

ULTIMA Building System Building 

Module (wall) 


Module (ceiling) 


Module (roof) 

Specification 

Sandwich panel 

thickness only 

76mm & 89mm 

thick 


(min) 

Integrity 


(min) 

Insulation 

Grade 

Core 

Material 

Cert. 

No. 

60 15 A PUR 592a/03 

47mm thick 60 60 A PUR 592a/04 

110mm thick - - B PUR 592a/05 

Notes: 

1. LPCB Ref. No. 592a/03, 592a/04 & 592a/05 Test specimen conformed to LPS1181 size requirements, except width was only 3.6m, 

the maximum width possible for the module. 

2. LPCB Ref. No. 592a/03 Wall panels laid with long joints in the vertical orientation. 

3. LPCB Ref. No. 592a/04 The test specimen for the ceiling fire resistance test was a combined ceiling and floor construction 

4. LPCB Ref. No. 592a/03 Wall inner surface lining 1x layer 12.5mm thick Gyproc Fireline Duplex, Lafarge GTEC Fire V or Knauf 

Fireshield Plasterboard with Renolit Minster PVC innerface lining. 

5. LPCB Ref. No. 592a/04 & 592a/05 Inner surface: interior polyester steel. 

6. LPCB Ref. No. 592a/03, 592a/04 & 592a/05 No assessment has been made of the structural performance of the module, or of the 

inclusion of windows and doors. Therefore there has been no evaluation of the performance should the fire break through a window 

or door. 

7. LPCB Ref. No. 592a/03, 592a/04 & 592a/05 Test Specimen short wall was 89mm thick and the long walls were 76mm thick. 

Yorkon Limited 

New Lane, Huntington, York YO32 9PT, United Kingdom 

Tel: +44 (0)1904 610990 • Fax: +44 (0)1904 610880 

E-mail: contact@yorkon.co.uk • Website: www.yorkon.co.uk 

Certificate No: 592a(1) to LPS 1181: Part 3 

Yorkon Room and Building Modules 

Product Name 

Specification Fire 

Fire Grade Core Cert. No. 

(sandwich panel 

thickness only) 

(mm) 

Resistance 

(min) 

Integrity 

Resistance 

(min) 

Insulation 

Material 

Yorkon Room Module (wall) 70 60 15 A PUR 592a/01 

Yorkon Room Module (ceiling) 47 60 60 A PUR 592a/02 

Yorkon Building Module (wall) 76 and 89 60 15 A PUR 592a/03 

Yorkon Building Module (ceiling) 47 60 60 A PUR 592a/04 

Yorkon Building Module (roof) 110 - - B PUR 592a/05 

20 Nov 2011 41


LPS 1181-3 (DRAFT) CLADDING USED IN POD CONSTRUCTION 

Notes: 

1. LPCB Ref. No. 592a/01, 592a/02, 592a/03, 592a/04 & 592a/05 Test specimen conformed to LPS1181 size requirements, except 

width was only 3.6m, the maximum width possible for the module. 

2. LPCB Ref. No. 592a/01 & 592a/03 Wall panels laid with long joints in the vertical orientation. 

3. LPCB Ref. No. 592a/01 Wall inner surface lining 1x layer 15mm thick Gyproc Fireline Duplex, Lafarge GTEC Fire V or Knauf 

Fireshield taper edge plasterboard 

4. LPCB Ref. No. 592a/02 Ceiling inner surface lining 2 layers 15mm thick Gyproc Fireline Plasterboard 83mm below lower surface of 

PUR sandwich panel 

5. LPCB Ref. No. 592a/02 & 592a/04 The test specimen for the ceiling fire resistance test was a combined ceiling and floor construction 

6. LPCB Ref. No. 592a/03 Wall inner surface lining 1x layer 12.5mm thick Gyproc Fireline Duplex, Lafarge GTEC Fire V or Knauf 

Fireshield taper edge plasterboard. 

7. LPCB Ref. No. 592a/04 & 592a/05 Inner surface: interior polyester steel 

8. LPCB Ref. No. 592a/01, 592a/02, 592a/03, 592a/04 & 592a/05 No assessment has been made of the structural performance of the 

module, or of the inclusion of windows and doors. Therefore there has been no evaluation of the performance should the fire break 

through a window or door. 

9. LPCB Ref. No. 592a/03, 592a/04 & 592a/05 Test Specimen short wall was 89mm thick and the long walls were 76mm thick 

42 20 Nov 2011

PART 1: SECTION 2.2 

LPS 1208 COMPOSITE CONSTRUCTION ELEMENTS 

LPS 1208: LPCB test and performance requirements for walls, cavity barriers, floors and roofs defines the test 

and performance requirements to satisfy the fire resistance requirements for compartmentation given in the 

LPC Design Guide for Fire Protection of Buildings: 2000. 

Products for use in the following elements of construction fall within the scope of LPS 1208: 

 

 

 

 

 

 

 

 

Loadbearing compartment walls 

Non-loadbearing compartment walls and partitions 

External walls 

Curtain walls 

Cavity barriers 

Roofs where fire resistance is required (loadbearing and non-loadbearing) 

Loadbearing compartment floors 

Insulated panels used for enclosing production and storage areas in food factories 

Note: Unless otherwise stated in individual listings, elements of construction have not been approved for load 

bearing capacity. 

ArcelorMittal Construction Belgium 

Zone Industrielle de Martinrou, 21b rue de Berlaimont, Fleurus, Belgium 

Tel: +32 (0) 718 70540 • Fax: +32 (0) 718 70541 

Website: www.arcelormittal.com 

Certificate No: 737a to LPS 1208 

Promistyl Feu (Wall panel) 

Product Specification 

Name Thickness (mm) 

Promistyl 

Feu 3003 

(Wall panel) 

Promistyl 

Feu 3506 

(Wall panel) 


(min) Integrity / 

Insulation (BS 476: 

Part 22) 

Wall Panel 

Orientation 

(H/V) (note 1) 

Max. 

Unsupported 

span (m) 

Grade 

Core 

material 

120 - 200 120/120 H 4.2 FR120 Mineral 

fibre 

120 - 200 120/120 V 4.0 FR120 Mineral 

fibre 

120 - 200 30/30 H/V 7.5 FR30 Mineral 

fibre 

120 - 200 60/60 H 7.5 FR60 Mineral 

fibre 

120 - 200 60/60 V 6.2 FR60 Mineral 

fibre 

120 - 200 90/60 H 5.6 FR90 Mineral 

fibre 

120 - 200 90/90 V 4.1 FR90 Mineral 

fibre 

80 - 100 120/60 V 4.0 FR60 Mineral 

fibre 

80 - 100 30/30 V 6.6 FR30 Mineral 

fibre 

80 - 100 60/60 V 4.0 FR60 Mineral 

fibre 

80 - 100 90/60 V 4.0 FR60 Mineral 

fibre 

120 - 200 30/30 H 7.5 FR30 Mineral 

fibre 

120 - 200 60/60 H 4.0 FR60 Mineral 

fibre 

Cert. 

No. 

737a/01 

737a/02 

Note: 


20 Nov 2011 43



2. LPCB ref No. 737a/01 & 737a/02 Promistyl Feu 3003 & 3506 wall panels are available with 0.5 to 0.63mm smooth, ribbed or grooved 

internal steel facing and 0.5 to 0.75mm smooth, ribbed, micro-ribbed or grooved external external steel facing. 



Tel: + 44 (0)2920 776677 • Fax: + 44 (0)2920 369161 


Certificate No: 545a to LPS 1208: Issue 2 

Firemaster Wall Extra 

Product Thickness 

Name (mm) 

Firemaster 

Wall Extra 



(min) 

Wall Panel 

Orientation 

(V/H) * 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 

75 30/30 V or H 3.0 FR30 Mineral 

Fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

150 60/60 V or H 7.5 

FR60 Mineral 

7.5 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/01 

Note: 

* Wall panel orientation, Vertical or Horizontal (V/H), relates to the long joint orientation of the Insulated panel. 


44 20 Nov 2011



Firemaster Ceiling Panel 


Name (mm) 

Firemaster 

Ceiling Panel 



(min) 

Wall Panel 

Orientation 

(V/H) 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 

100 60/60 - 4.2 FR60 Mineral 

fibre 

125 60/60 - 4.2 FR60 Mineral 

fibre 

150 60/60 - 4.2 FR60 Mineral 

fibre 

150 120/120 - 3.0 FR120 Mineral 

Fibre (note 

2) 

150 120/120 - 3.5 FR120 Mineral 

fibre 

150 60/60 - 6.0 FR60 Mineral 

fibre 

150 90/90 - 4.5 FR90 Mineral 

fibre (note 

2) 

150 90/90 - 4.7 FR90 Mineral 

fibre 

Cert. 

No. 

545a/02 

545a/12 

Note: 

1. LPCB ref 545a/12 - Ceiling panels to be stitched on both internal and external faces using 3.8mm diameter x 16mm long stainless 

steel rivets or 4.7mm diameter x 20mm long steel stitching screws at 300mm centres. 

2. Tervol DP-LX 12 stone mineral wool insulation core. 


Firemaster Wall Lite 


Name (mm) 

Firemaster 

Wall Lite 



(min) 

Wall Panel 

Orientation 

(V/H) * 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/03 

20 Nov 2011 45



Product 

Name 

Thickness 

(mm) 



(min) 

Wall Panel 

Orientation 

(V/H) * 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 

Cert. 

No. 

Note: 



Europanel Extra (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Europanel 

Extra (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span(m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/05 

Note: 



46 20 Nov 2011



Europanel Premier (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Europanel 

Premier (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/06 

Note: 



Europanel Lite (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Europanel 

Lite (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/07 

20 Nov 2011 47



Product 

Name 

Thickness 

(mm) 



(min) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

Note: 



Rockspan Extra (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Rockspan 

Extra (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/08 

48 20 Nov 2011



Product 

Name 

Thickness 

(mm) 



(min) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

Note: 



Rockspan Lite (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Rockspan 

Lite (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/09 

Note 

* Wall panel orientation, Vertical or Horizontal (V/H), relates to the long joint orientation of the Insulated panel 


20 Nov 2011 49



Rockspan Ultima (wall panel) 

Product 

Name 

Thickness 

(mm) 



(min) 

Rockspan 

Ultima (wall 

panel) 

Wall Panel 

Orientation 

(V/H) * 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/10 

Note: 

1. LPCB ref 545a/10 - Rockspan Ultima 150mm & 175mm thick wall panel joints to be stitched on both internal and external faces using 

4.7mm diameter x 20mm long self-tapping screws at 300mm centres, the 200mm panel does not require stitching. 



Firemaster Wall Ultima (wall panel) 

Product Name Thickness 

(mm) 



(min) 

Firemaster Wall 

Ultima (wall 

panel) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/11 

Notes: 

1. LPBC Ref 545a/11 - Firemaster Wall Ultima wall panel joints to be stitched on both internal and external faces using 4.7mm diameter 

x 20mm long self-tapping screws at 300mm centres. 

* Wall panel orientation, vertical or Horizontal (V/H), relates to the long joint orientation of the Insulated panel. 


Rainspan 

Product Name 

Rainspan - 

Argeton 

terracotta tile 

system 

Rainspan - 

Linear system 

Rainspan - 

Parklex timber 

veneer system 

Rainspan - 

Rockpanel 

system 

Thickness 

(mm) 



(min) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/13 

545a/14 

545a/15 

545a/16 

50 20 Nov 2011



Product Name 

Rainspan - 

Corium brick slip 

system 

Rainspan - 

Generic timber 

system 

Rainspan - 

Clicktile steel 

tray system 

Thickness 

(mm) 



(min) 

Wall Panel 

Orientation 

(V/H)* 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Cert. 

No. 

545a/17 

545a/18 

545a/19 

Notes: 

1. LPCB Ref 545a/13 to 545a/19 - Rainspan, the thickness specified relates to the insulated panel thickness only and does not include 

the facade system depth. 




Tel: +44 (0)2920 790722 • Fax: +44 (0)2920 793149 


Certificate No: 879b to LPS 1208: Issue 2 

Product Name 


system) 


system) 


system) 


system) 


system) 


system) 


system) 


system) 


system) 

System 

Specification 

Thickness 

(mm) 

Wall panel 

orientation 

(H/V) 

Maximum 

Unsupported 

Span (m) 


(minutes) 

Integrity / 

Insulation 

Grade 

Core 

material 

See note 2 V 3.0 240 / 30 FR30 Mineral 

Wool 

879b/09 

See note 2 V 3.0 240 / 30 FR30 Mineral 879b/10 

Wool 

See note 2 V 3.0 240 / 30 FR30 Mineral wool 879b/11 

See note 2 V 3.0 240 / 30 FR30 Mineral 

Wool 

See note 2 H 3.0 240 / 30 FR30 Mineral 

Wool 


Wool 


Wool 


Wool 


Wool 

Cert. 

No. 

879b/12 

879b/13 

879b/14 

879b/15 

879b/16 

879b/17 

Notes 

20 Nov 2011 51



1. Elite wall systems must have the sheeting rail spacing at a maximum of 2m & internal liner sheet side lap joints stitched using steel 

rivets at 300mm centres, the external liner must be fixed to the channels of the spacer system using self-drilling, self-tapping screws 

at nominal 400mm centres. 

2. The minimum permissible stone mineral wool thickness is 180mm, or for systems with horizontally laid external weather sheets where 

the eurobar spacer rails are vertical and the insulation in the core is supported by additional steel Z- section supports, and with a 

minimum density of the insulation of 33kg/m³ the minimum insulation thickness can be reduced to 150mm. 

3. Please refer to BRE Assessment Report CC248407 for approved alternative spacer systems, internal & external profiles, internal & 

external profile coatings and insulation cores for the Elite systems 51, 52, 53, 54, 55, 56, 57, 58 & 60. 



Tel: +44 (0)151 426 7171 • Fax: +44 (0)151 493 1331 



Composite Panels 

Product Name 

Hemsec PIR Firecheck (wall 

panel) 

Hemsec PIR Firecheck (ceiling 

panel) 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

span (m) 

Wall panel 

orientation 

(H/V) 

(note 1) 

BS 476: 

Part 22 

Fire 

Resistance 


/ 

Insulation 

Grade 

Core 

Material 

Cert. 

No. 

100 - 200 4.0 H 30/30 FR30 PIR 558a/16 

100 - 200 4.0 H 60/30 FR30 PIR 

100 - 200 4.0 V 30/30 FR30 PIR 

100 - 200 4.0 V 60/30 FR30 PIR 

175 - 200 4.0 H 30/30 FR30 PIR 

175 - 200 4.0 H 60/60 FR60 PIR 

175 - 200 4.0 V 60/60 FR60 PIR 

175 - 200 7.5 V 30/30 FR30 PIR 

100 - 200 7.5 - 60/30 FR30 PIR 558a/17 

175 - 200 4.5 - 60/60 FR60 PIR 

175 - 200 7.5 - 30/30 FR30 PIR 

Notes: 

PIR Firecheck panel: 


2. The Hemsec LPS 1208 Model Specification document QCD: 064/1 relating to the PIR Firecheck wall and ceiling panels LPCB ref 

558a/16 and 558a/17 contains the critical components and specific stitching requirements needed for achieving LPCB compliant 

panel systems. Copies of the Model Specification are available on request, plese contact the Hemsec Sales Department. 


Hemsec SIP Firecheck 

Product Name Total 

system 

thickness 

(mm) 

Hemsec SIP 

Firecheck (wall 

system) 

Fire 

resistance 

(min) 

Integrity 

Fire 

resistance 

(min) 

Insulation 

Load 

bearing 

capacity 

under test 

conditions 

160 to 287 75 75 11.67kN 

per linear 

metre 

257.5 - 

329.5 

101 101 Not 

applicable 

Max 

unsupported 

span (m) 

Grading 

Core 

Material 

Cert. 

No. 

2.6 FR60 PUR 558a/11 

3.0 FR90 PUR 558a/13 

Notes: 

SIP Firecheck system: 

1. LPCB Ref. 558a/11 - Hemsec SIP Firecheck panel system consists of rigid polyurethane foam core (125mm - 252mm thick) 

sandwiched between 15 mm orientated strand boards (OSB-3). The system was clad on the fire exposed face with a single layer of 

British Gypsum ‘Gyproc’ 12.5mm wall board (outer layer) and a single layer of British Gypsum ‘Gyproc Fireline’ 12.5mm board (inner 

layer), board layer joints staggered by 600mm and fixed to softwood timber batons at 600mm centres with 3.5mm x 50mm dry wall 

screws at 300mm centres. A total load of 35kN was applied for the duration of the test to a 3.0m wide test sample. 

52 20 Nov 2011



2. LPCB Ref 558a/13 - SIP Firecheck wall system is approved to LPS 1208 as a non load-bearing, non structural built up wall system of 

the following configuration; Rigid polyurethane foam core (150mm to 222mm thick) sandwiched between 15 mm orientated strand 

boards (Krono OSB-3), the panel size is 1.2m x 3.0m and installed with 3 metre joints vertical and consisting of 148mm deep x 70mm 

thick x 3000mm long timber spline joints inserted into 35mm pre-formed rebates in the core insulation, the joints are fixed with 

adhesive and nail fixings at 100mm centres. The system is clad on the fire exposed face with two layers of British Gypsum wall 

boards; A single layer of ‘Gyproc’ 12.5mm wall board (outer layer) and a single layer of ‘Gyproc Fireline’ 15mm board (inner layer), 

with the wall board joints between layers staggered by 600mm and fixed to softwood timber battens 50mm x 50mm spaced at 600mm 

centres with 3.5mm x 50mm dry wall screws at 300mm centres, the stud cavity is filled with Knauf Rocksilk Universal slab RW33 

insulation. 

ISOCAB France S.A. 

Avenue de la Gironde, Z.I. Petite Synthe, 59640 Dunkerque, France 

Tel: +33 328 29 26 30 • Fax: +33 328 60 11 93 

E-mail: info@isocabfrance.fr • Website: www.isocab.be 


Product Name 

Specification 

Thickness 

(mm) 

Maximum 

unsupported 

span 

(m) 

Wall Panel 

orientation 

(HV) (note 

1) 

Fire 

Resistance 

(min) 


Grade 

Core 

Material 

IND PIR (Wall panel 220 4.5 V 6/68 FR60 PIR 465b/01 

IND PIR (Wall panel) 110 4.5 V 37/37 FR30 PIR 

120 4.5 V 37/37 FR30 PIR 

140 4.5 V 37/37 FR30 PIR 

170 4.5 V 37/37 FR30 PIR 

200 4.5 V 68/68 FR60 PIR 

IND 20 PIR (Ceiling 200 4.4 - 42/42 FR30 PIR 465b/03 

panel) 

120 to 300 120 to 300 6.0 V 60/60 FR60 Mineral 844b/01 

Decaroc 50 F (Wall 

panel) 

Decaroc 50F (Wall 

panel) 

Decaroc 50 F (Ceiling 

panel) 

Fibre 

120 to 300 4.0 H 240/120 FR120 Mineral 

Fibre 

120 to 300 4.0 V 180/120 FR120 Mineral 

Fibre 

120 to 300 4.0 V 240/120 FR120 Mineral 

Fibre 

120 to 300 6.0 H 120/120 FR120 Mineral 

Fibre 

120 to 300 6.0 H 30/30 FR30 Mineral 

Fibre 

120 to 300 6.0 H 60/60 FR60 Mineral 

Fibre 

120 to 300 6.0 V 120/120 FR120 Mineral 

Fibre 

120 to 300 6.0 V 30/30 FR30 Mineral 

Fibre 

120 to 300 6.0 V 90/90 FR90 Mineral 

Fibre 

80 to 120 4.0 H 60/60 FR60 Mineral 

Fibre 

80 to 120 6.0 H 30/30 FR30 Mineral 

Fibre 

120 to 300 4.0 H 180/120 FR120 Mineral 

Fibre 

120 to 300 6.0 H 90/90 FR90 Mineral 

Fibre 

120 to 300 5.0 - 180/120 FR120 Mineral 

Fibre 

120 to 300 6.0 - 120/120 FR120 Mineral 

Fibre 

120 to 300 6.0 - 30/30 FR30 Mineral 

Fibre 

120 to 300 6.0 - 60/60 FR60 Mineral 

Fibre 

120 to 300 6.0 - 90/90 FR90 Mineral 

Fibre 

Cert. 

No. 

844b/02 

20 Nov 2011 53



Notes: 

1) LPCB Refernce No. 844b/02, ceiling panel joints shall be stitched at 500mm centre's on the unexposed face with flat head steel 

screws. 

Isoclad Limited 

10 Alder Road, West Chirton North Industrial Estate, North Shields, Tyne & Wear NE29 8SD, United Kingdom 

Tel: +44 (0)191 258 5052 • Fax: +44 (0)191 259 5742 

E-mail: sales@isoclad.co.uk • Website: www.isoclad.co.uk 


Product Name 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

Panel 

Span 

(m) 

Wall Panel 

orientation 

(H/V) 

(note 1) 

Fire 

Resistance 

(min) 

Integrity / 

Insulation 

Grade 

Core 

Material 

Firestop 10 (wall panel) 75 3.0 V 30 / 30 FR30 Mineral 

fibre 

100 4.5 V 60 / 60 FR60 Mineral 

fibre 

100 5.5 V 30 / 30 FR30 Mineral 

fibre 

125 4.5 V 60 / 60 FR60 Mineral 

fibre 

125 5.5 V 30 / 30 FR30 Mineral 

fibre 

150 5.0 V 90 / 90 FR90 Mineral 

fibre 

150 5.5 V 30 / 30 FR30 MIneral 

fibre 

150 5.5 V 60 / 60 FR60 Mineral 

fibre 

175 5.0 V 90 / 90 FR90 Mineral 

fibre 

175 5.5 V 30 / 30 FR30 Mineral 

fibre 

175 5.5 V 60 / 60 FR60 Mineral 

fibre 

200 5.0 V 90 / 90 FR90 Mineral 

fibre 

200 5.5 V 30 / 30 FR30 Mineral 

fibre 

200 5.5 V 60 / 60 FR60 Mineral 

fibre 

Firestop10 (Wall Panel) 100 7.5 H or V 240 / 30 FR30 Mineral 

fibre 

100 7.5 H or V 240 / 60 FR60 Mineral 

fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 


fibre 

Firestop10 (Wall Panel) 100 4.35 H 60 / 60 FR60 Mineral 

fibre 

100 6.0 H 30 / 30 FR30 Mineral 

fibre 

Cert. 

No. 

142a/01 

54 20 Nov 2011

Product Name 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

Panel 

Span 

(m) 



Wall Panel 

orientation 

(H/V) 

(note 1) 

Fire 

Resistance 

(min) 

Integrity / 

Insulation 

Grade 

Core 

Material 

125 4.35 H 60 / 60 FR60 Mineral 

fibre 

125 6.0 H 30 / 30 FR30 Mineral 

fibre 

150 4.35 H 60 / 60 FR60 Mineral 

fibre 

150 6.0 H 30 / 30 FR30 Mineral 

fibre 

175 4.35 H 60 / 60 FR60 Mineral 

fibre 

175 6.0 H 30 / 30 FR30 Mineral 

fibre 

200 4.35 H 60 / 60 FR60 Mineral 

fibre 

200 6.0 H 30 / 30 FR30 Mineral 

fibre 

Firestop 12 (wall panel) 75 3.0 V 30 / 30 FR30 Mineral 142a/02 

fibre 

75 3.0 V 60 / 60 FR60 Mineral 

fibre 

100 5.5 V 90 / 90 FR90 Mineral 

fibre 

100 6.0 V 60 / 60 FR60 Mineral 

fibre 

100 7.5 V 30 / 30 FR30 Mineral 

fibre 

125 5.5 V 90 / 90 FR90 Mineral 

fibre 

125 6.0 V 60 / 60 FR60 Mineral 

fibre 

125 7.5 V 30 / 30 FR30 Mineral 

fibre 

150 5.5 V 120 / 120 FR120 Mineral 

fibre 

150 5.5 V 90 / 90 FR90 Mineral 

fibre 

150 6.0 V 60 / 60 FR60 Mineral 

fibre 

150 7.5 V 30 / 30 FR30 Mineral 

fibre 

175 5.5 V 120 / 120 FR120 Mineral 

fibre 

175 5.5 V 90 / 90 FR90 Mineral 

fibre 

175 6.0 V 60 / 60 FR60 Mineral 

fibre 

175 7.5 V 30 / 30 FR30 Mineral 

fibre 

200 5.5 V 120 / 120 FR120 Mineral 

fibre 

200 5.5 V 90 / 90 FR90 Mineral 

fibre 

200 6.0 V 60 / 60 FR60 Mineral 

fibre 

200 7.5 V 30 / 30 FR30 Mineral 

fibre 

Firestop 12C (ceiling 100 to 200 3.0 - 60 / 60 FR60 Mineral 142a/03 

panel) 

fibre 

100 to 200 5.5 - 30 / 30 FR30 Mineral 

fibre 

Isoclad PIR (Wall panel) 100 3.0 V 46 / 41 FR30 PIR 142a/05 

Isoclad PIR (Ceiling 

150 3.4 - 80 / 50 FR30 PIR 142a/06 

panel) 

Isoclad PIR 40 (Wall 

Panel) 

150 4.0 V 60/30 FR30 PIR 142a/07 

Firestop 12 (Ceiling 

Panel) 

150 6.0 V 30/30 FR30 PIR 

100 4.4 - 63/63 FR60 Mineral 

fibre 

Cert. 

No. 

142a/08 

20 Nov 2011 55



Product Name 

Securiclad SR4 (Wall 

Panel) 

Securiclad SR4 (Ceiling 

Panel) 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

Panel 

Span 

(m) 

Wall Panel 

orientation 

(H/V) 

(note 1) 

Fire 

Resistance 

(min) 

Integrity / 

Insulation 

Grade 

Core 

Material 

100 4.0 V 120/90 FR90 Mineral 

fibre 

100 4.0 V 180/90 FR90 Mineral 

fibre 

100 4.0 V 240/90 FR90 Mineral 

fibre 

100 4.0 V 90/90 FR90 Mineral 

fibre 

100 5.2 V 60/60 FR60 Mineral 

fibre 

100 7.5 V 30/30 FR30 Mineral 

fibre 

100 4.1 - 60/60 FR60 Mineral 

fibre 

100 7.5 - 30/30 FR30 Mineral 

fibre 

Cert. 

No. 

142a/09 

142a/10 

Notes: 


2. LPCB Ref No 142a/01 where the Firestop 10 wall panels maximum unsupported span is listed as 7.5m the joints between the panels 

must be stitched on both internal and external faces with 4mm Ø stainless steel rivets at nominal 200mm centres and be sealed with 

Hilti CP 606 intumescent sealant on both faces. 

3. LPCB ref. No 142a/01 where the Firestop 10 wall panels are listed as installed horizontally (H) only, the joints between the panels are 

unstitched and sealed with a bead of Geocel Dow Corning Firestop 700 silicone sealant on both joint faces. 

4. LPCB Ref. No. 142a/03 The joints on the Firestop12 ceiling panels should be stitched with 3mm diameter rivets at 300mm centres on 

the internal and external face. 

5. LPCB ref. No 142a/05 Isoclad PIR Wall panels shall be stitched with 4.2mm diameter rivets at 150mm centres on the external face. 

6. LPCB ref. No 142a/06 Isoclad PIR ceiling panels shall be stitched with 4.2mm diameter rivets at 200mm centres on the internal and 

external face. 

7. LPCB ref. No 142a/07 Isoclad PIR 40 wall palenls, a bead of Hilti CP601 intumescent sealant call be applied to the female joint profile 

prior to installation then stitched with 4mm diameter rivets at 200mm centres on the internal and external face and sealed with a 

further bead of Hilti CP 601 intumescent sealant on both faces. 

8. LPCB ref No 142a/08, 142a/09 & 142a/10 the joints between the panels are unstitched. A bead of Envirograph 62 intumescent 

fieproof sealant shall be applied to the female joint profile prior to installation, and sealed with a further bead of Envirograph 62 

intumescent fireproof sealant on both faces. 

Kingspan Ltd 


Tel: +353 42 969 8572 • Fax: +353 42 969 8576/77 



Product Name 

Kingspan Ecosafe KS1100CS (wall 

panel) 

Kingspan Ecosafe KS1100CS 



panel) 

Kingspan Ecosafe 

KS1100CS(ceiling panel) 


panel) 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Length (m) 

Grade 

Core 

Material 

Cert. 

No. 

100, 125, 

150, 

175 & 200 

195 31 4.00 FR30 PIR 279b/05 

100, 125, 150 58 32 3.40 FR30 PIR 279b/06 

175 & 200 

175 & 200 240 64 3.00 FR60 PIR 279b/07 

175 & 200 148 67 3.30 FR60 PIR 279b/08 

175 & 200 69 61 4.00 FR60 PIR 279b/09 

Note: 

1. LPCB Ref 279b/05, 279b/06, 279b/07, 279b/08 & 279b/09 Refer to model specification LPCB 11 Rev 1 for full details 

56 20 Nov 2011



Kingspan Ltd. 


Tel: +44 (0)1352 716100 • Fax: +44 (0)1352 716161 



Product Name 


panel) 




panel) 




panel) 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Length (m) 

Grade 

Core 

Material 

Cert. 

No. 

100, 125, 

150, 

175 & 200 

195 31 4.00 FR30 PIR 279b/05 

100, 125, 58 32 3.40 FR30 PIR 279b/06 

150, 

175 & 200 

175 & 200 240 64 3.00 FR60 PIR 279b/07 

175 & 200 148 67 3.30 FR60 PIR 279b/08 

175 & 200 69 61 4.00 FR60 PIR 279b/09 

Note: 

1. LPCB Ref 279b/05, 279b/06, 279b/07, 279b/08 & 279b/09 Refer to model specification LPCB 11 Rev 1 for full details. 

Modular Panel Systems Limited 

Mohill, Co.Leitrim, Ireland 

Tel: +353 719631162 • Fax: +353 719651979 

E-mail: info@modular.ie • Website: www.modular.ie 

Certificate No: 750a to LPS 1208 Issue 2 

Product Name 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Max 

Unsupported 

Length (m) 

Grade 

Core 

Material 

Enviro Panel PIR (wall panel) 100 43 15 3.0 FR15 PIR 750a/01 

150 60 48 3.0 FR30 PIR 

200 60 48 3.0 FR30 PIR 

Enviro Panel Mineral wool (wall 100 121 44 7.5 FR30 Mineral wool 750a/02 

panel) 

Enviro Panel Mineral wool 150 121 68 3.0 FR60 Mineral wool 750a/03 


Enviro Panel PIR (wall panel) 100 30 15 3.0 FR15 PIR 750a/04 

150 60 30 3.0 FR30 PIR 

200 60 30 3.0 FR30 PIR 

Enviro Panel Mineral wool (wall 100 120 30 7.5 FR30 Mineral wool 750a/05 

panel) 

Enviro Panel Mineral wool 150 120 60 3.0 FR60 Mineral wool 750a/06 


Enviro Panel Mineral wool (wall 

panel) 

150 120 60 7.5 FR60 Mineral wool 750a/07 

Cert. 

No. 

Notes: 

1. LPCB Ref. 750a/01, 750a/02, 750a/04, 750a/05 & 750a/07 Wall panels shall be installed with the long joint in the vertical orientation. 

20 Nov 2011 57



2. LPCB Ref. 750a/01, 750a/03, 750a/04 & 750a/06 - A strip of Pyrostrip graphite self-adhesive tape, 10mm wide x 2mm thick, shall be 

applied between the overlap in the steel skins of adjacent panels, the joints of the Enviro panels shall then be stitched with 4.8mm dia 

x 10mm stainless steel rivets @ 300mm centres on both the exposed and internal face. 

3. LPCB Ref. 750a/02, 750a/05 & 750a/07 - A strip of Pyrostrip graphite self-adhesive tape, 10mm wide x 2mm thick, shall be applied 

between the overlap in the steel skins of adjacent panels, the joints of the Enviro panels shall then be stitched with 3.2mm dia x 

12mm stainless steel rivets @ 300mm centres on both the external and internal face. 

4. LPCB Ref. 750a/01, 750a/02 & 750a/03 PIR and Mineral wool panels are supplied with a castellated joint panel edge profile. 

5. LPCB Ref. 750a/04, 750a/05 & 750a/06 PIR and Mineral wool panels are supplied with a flat, butt joint panel edge profile. 

6. LPCB Ref. 750a/07 Mineral wool wall panels are supplied with a castellated joint or a flat, butt joint panel edge profile. 

Panel Projects Limited 

Portview Road, Avonmouth, Bristol BS11 9LQ, United Kingdom 

Tel: +44 (0)117 316 7000 • Fax: +44 (0)117 316 7001 


Wall Panels 

Product Name 

Firecold (wall 

panels) 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Maximum 

unsupported 

span (m) 

Grade 

Core 

Material 

Cert. No. 

100 30 30 6.2 FR30 Mineral wool 881a/01 

100 60 60 4.0 FR60 Mineral wool 



Note: 

1. LPCB Ref 881a/01 Wall panels to be installed with long joints in the vertical orientation only. 

Paroc Panel System Oy Ab 

FIN-21600, Parainen, Finland 

Tel: +358 46 876 8000 • Fax: +358 46 876 8702 

E-mail: panelinfo@paroc.com • Website: www.paroc.com 


AST F, AST S & AST T Wall Panels and AST E Ceiling Panels 


Thickness 

(mm) 

Maximum 

Unsupported 

span (m) 

Wall panel 

orientation 

(H/V) (note 

1) 

Fire 

Resistance 

(mm) 

Integrity / 

Insulation 

Grade 

Core 

Material 

PAROC AST F (wall panel) 50 4.6 V 30/30 FR30 Mineral wool 381a/01 

80 4.0 V 90/90 FR90 Mineral wool 












100 - 240 4.0 H 120/120 FR120 Mineral wool 



Cert. 

No. 

58 20 Nov 2011

Product Name 

Specification 

Thickness 

(mm) 

Maximum 

Unsupported 

span (m) 



Wall panel 

orientation 

(H/V) (note 

1) 

Fire 

Resistance 

(mm) 

Integrity / 

Insulation 

Grade 

Core 

Material 

150 - 240 4.0 V 240/240 FR240 Mineral wool 






50 -240 4.0 H 30/30 FR30 Mineral wool 



PAROC AST S (wall panel) 80 4.0 V 60/30 FR30 Mineral wool 381a/02 





















PAROC AST E (ceiling 

panel) 

Cert. 

No. 

100 6.5 - 60/60 FR60 Mineral wool 381a/04 

100 8.2 - 30/30 FR30 Mineral wool 

PAROC AST T (wall panel) 80 4.0 V 30/30 FR30 Mineral wool 381a/05 


















Notes: 

1. Wall orientation, Horizontal or Vertical (H/V), relates to the long joint orientation. 

2. LPCB Ref 381a/01, 381a02 and 381a/05 when panels are laid with the long joint in the horizontal orientation the joints shall be 

stitched on the internal and external face at nominal 150mm centres. 

20 Nov 2011 59



Promat UK Ltd 

The Sterling Centre, Eastern Road, Bracknell, Berkshire RG12 2TD, United Kingdom 

Tel: +44 (0)1344 381300 • Fax: +44 (0)1344 381301 

Website: www.promat.co.uk 


Product Name 

Specification 

Thickness 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Length (m) 

Grading 

Core 

Material 

Cert. No. 

Durawall 120 150 120 120 5.50 FR120 Mineral fibre 545a/01 

Durawall 90 125 90 90 5.50 FR90 Mineral fibre 



Notes: 

1. LPCB Ref. No’s 545a/01, 545a/03 and 545a/11 - Wall panels can be installed vertically or horizontally. 

2. LPCB Ref. No’s 545a/11 - wall panel joints to be stitched on both internal and external faces using 4.7mm Diameter x 20mm long 

self-tapping screws at 300mm centres. 

Ruukki Construction Oy 

PO Box 138, (Suolakivenkatu 1), 00811 Helsinki, Finland 

Tel: +358 20 592 7521 • Fax: +358 20 592 7708 

E-mail: simo.heikkila@ruukki.com • Website: www.ruukki.com 


Product 

Name 

Specification 


Max 

Unsupported 

Span (m) 

Wall panel 

orientation 

(H/V) 

(note 1) 

Fire 

resistance 

(min) 

Integrity / 

Insulation 

Grade 

Core 

material 

SPA-E 100 & 125 3.0 V or H 60/60 FR60 Mineral 

wool 

100, 125, 150, 175, 200, 6.0 V or H 30/30 FR30 Mineral 

230 & 260 

wool 

150, 175, 200, 230 & 260 3.0 V or H 90/90 FR90 Mineral 

wool 


wool 

SPA-I 100 & 125 3.0 V or H 60/60 FR60 Mineral 

wool 


wool 


wool 

SPA-F 100 3.0 V 180/120 FR120 Mineral 

wool 

100 3.8 H 120/120 FR120 Mineral 

wool 

100 4.5 V 120/120 FR120 Mineral 

wool 

100 5.1 H 90/90 FR90 Mineral 

wool 

100 6.0 V 90/90 FR90 Mineral 

wool 

100, 125, 150, 175, 200, 6.0 H or V 30/30 FR30 Mineral 

230 & 260 

wool 


230 & 260 

wool 

Cert. 

No. 

660a/03 

660a/04 

660a/05 

60 20 Nov 2011



Product 

Name 

Specification 


Max 

Unsupported 

Span (m) 

Wall panel 

orientation 

(H/V) 

(note 1) 

Fire 

resistance 

(min) 

Integrity / 

Insulation 

Grade 

Core 

material 

125, 150, 175, 200, 230 & 

260 

3.0 H or V 240/180 FR180 Mineral 

wool 

125, 150, 175, 200, 230 & 

260 


wool 

125, 150, 175, 200, 230 & 

260 


wool 

125, 150, 175, 200, 230 & 

260 


wool 

150, 175, 200, 230 & 260 7.5 (note 2) H or V 120/120 FR120 Mineral 

wool 


wool 


wool 


wool 


wool 


wool 

SPA-S 100 3.0 V 180/120 FR120 Mineral 

wool 

100 3.8 H 120/120 FR120 Mineral 

wool 

100 4.5 V 120/120 FR120 Mineral 

wool 

100 5.1 H 90/90 FR90 Mineral 

wool 

100 6.0 V 90/90 FR90 Mineral 

wool 


230 & 260 

wool 


230 & 260 

wool 

125, 150, 175, 200, 230 & 3.0 H or V 240/180 FR180 Mineral 

260 

wool 


260 

wool 


260 

wool 


260 

wool 


wool 


wool 


wool 


wool 


wool 


wool 

Cert. 

No. 

660a/06 

Note: 


2. LPCB Ref No. 660a/05 & 660a/06 where panels are approved with a span of 7.5m the joints must be stitched on both faces at 

300mm centers using 4.2mm-diameter flat head screws and then sealed using a Teknosafe 2002-00 intumescent paint. 

20 Nov 2011 61



Specialist Panels UK Limited 

Bolam Business Park, Bassington Drive, Bassington Industrial Estate, Cramlington, Northumberland NE23 

8AD, United Kingdom 

Tel: +44(0) 1670 739116 • Fax: +44(0) 1670 732955 

E-mail: isowall@btinternet.com • Website: www.isowall.org.uk 

Certificate No: 957a to LPS1208: Issue 2 

Product Name 

Isowall (wall 

panel) 

Specification 

Thickness 

(mm) 

Fire 

Resistance 


Fire 

Resisitance 

(min) 

Insulation 

Max 

Unsupported 

Span (m) 

Grading 

Core 

Material 

100 98 98 4.0 FR90 Mineral 

wool 

125 120 120 3.0 FR120 Mineral 

wool 

150 265 208 3.0 FR120 Mineral 

wool 

150 265 208 4.0 FR90 Mineral 

wool 

Cert. 

No. 

957a/01 

Note: 

1. LPCB Ref No. 957a/01, Wall panels to be installed with long joints vertically only. 

Stancold plc 


Tel: +44 (0)117 316 7000 • Fax: +44 (0)117 316 7001 

E-mail: sales@stancold.co.uk • Website: www.stancold.co.uk 


Wall panels 

Product Name 

Specification 

Thickness 

(mm) 


Integrity 

(min) 


Insulation 

(min) 

Maximum 

unsupported 

span (m) 

Grade 

Core 

material 

Cert. No. 

Firecold (wall panels) 100 30 30 6.2 FR30 Mineral wool 881a/01 




Note: 

1. LPCB Ref 881a/01 Wall panels to be installed with long joints in the vertical orientation only. 

62 20 Nov 2011



Trimo d.d 


Tel: 00386 73460200 • Fax: 0038 673460127 


UK Supplier 


Tel: +44 (0) 1270 665303 • Fax: +44 (0) 1270 664294 



Trimotherm Panels 


Thickness 

(mm) 

Trimotherm FTV 

(wall panel) 

Specification 

Orientation 

of 

Long Edges 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 

100 Horizontal 30 30 7.25 FR30 Mineral 

wool 


wool 


wool 

100 Vertical 30 30 7.25 FR30 Mineral 

wool 


wool 


wool 

120 Horizontal 30 30 8.00* FR30 Mineral 

wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 

Cert. 

No. 

650a/01 

20 Nov 2011 63



Product Name 

Trimotherm FTV- 

H (wall panels) 

Trimotherm SNV 

(ceiling panels) 

Specification 

Thickness 

(mm) 

Specification 

Orientation 

of 

Long Edges 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Maximum 

Unsupported 

Span (m) 

Grade 

Core 

Material 


wool 


wool 


wool 


wool 


wool 


wool 


wool 

200 Vertical 90 90 600 FR90 Mineral 

wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 


wool 

100 - 98 95 2.00 FR90 Mineral 

wool 

120 - 98 95 2.00 FR90 Mineral 

wool 

150 - 98 95 2.00 FR90 Mineral 

wool 

200 - 98 95 2.00 FR90 Mineral 

wool 

Cert. 

No. 

650a/02 

650a/03 

Note: 

1. LPCB Ref. No. 650a/01 - unsupported spans marked *, span can be extended to 10.4m in respect of the length of the panel in 

horizontal laid orientation only. 

64 20 Nov 2011


LPS 1581 EXTERNAL CLADDING SYSTEMS ON A MASONRY SUBSTRATE 

LPS 1581 Requirements and tests for LPCB approval of non-load bearing External Thermal Insulated 

Cladding Systems with rendered finishes (ETICS) or Rain Screen Cladding systems (RSC) applied to the 

masonry face of a building. 

20 Nov 2011 65


LPS 1581 EXTERNAL THERMAL INSULATED CLADDING (ETICS) ON MASONRY SUBSTRATES 



masonry face of a building 

The test method used is BS 8414-1:2002 Test method for non-load bearing external cladding systems applied 

to the face of the building and is representative of an external fire source or fully developed (post-flashover) 

fire in a room venting through an opening such as a window aperture that exposes the external surfaces of the 

cladding system to the effects of the impinging flames. The test method determines external and potential 

internal (within the ETICS system) fire spread and, where a void exists, the extent of fire spread through the 

void. 

External Thermal Insulated Composite Systems (ETICS) are systems which are applied to a masonry or 

concrete leaf, typically comprising of a number of layers including an insulation layer, a reinforcing mesh and 

external render or pre-formed slips or similar finish. 

Dryvit UK Limited 

Unit 4, Wren Park, Hitchin Road, Shefford, Bedfordshire SG17 5JD, United Kingdom 

Tel: +44 (0)1462 819555 • Fax: +44 (0)1462 819556 

E-mail: ukenquiries@dryvit.com • Website: www.dryvit.co.uk 


Product Name 

Roxsulation S 

Outsulation & 

Outsulation Plus 

Fedderlite Panel 

system 

External 

layer detail 

See Note 

1 & 3 

See Note 

1 & 5 

See Note 

1 & 8 

Insulation 

material type & 

thickness 

Mineral wool, 

thickness range 

40-200mm 

See Note 4 

EPS, thickness 

50-250mm 

See Note 6 


range 50-120mm 

Cavity type and maximum 

depth 

Firebreak 

detail 

EN 13501-1 

Classification 

No cavity Continuous No Performance 

Determined 

No cavity See Note 7 B-s2-d0 

See Note 1 

Encapsulated cavity 

between substrate and rear 

of Fedderlite panel 

See Note 9 

B-s2-d0 

See Note 1 

Cert. 

No. 

784a/01 

784a/02 

985a/01 

Notes: 

General. 

1. LPCB Ref. No. 784a/01, 784a/02 & 985a/01 - Approved systems consist of Dryvit Genesis base coat, Dryvit Standard Plus reinforcing 

mesh, with or without Dryvit primer and a Dryvit Quarzputz PMRB, Sandpebble PMRB or Sandpebble Fine PMRB top coat, natural or 

tinted with a Qpcs value of up to 2.95MJ/kg. 

LPCB Ref. No. 784a/02 & 985a/01 The stated EN 13501-1 classification is applicable to systems with a PMRB top coat, natural or 

tinted with a Qpcs value up to 2.63MJ/kg only. 

2. Subject to the stated conditions the Roxsulation S system (LPCB Ref. No 784a/01) shall be installed in accordance with the 

application detail contained within Dryvit document DUK628 (June 2008). Outsulation & Outsulation Plus systems (LPCB Ref. No. 

784a/02) shall be installed in accordance with the application detail contained within Dryvit documents DUK204 (21/01/08) and 

DUK218 (V1 21-2-07) respectively. And the Fedderlite panel system (LPCB Ref. No. 985a/01) shall be installed in accordance with 

the application detail contained within Dryvit document DUK217 Issue 003 31/01/11 - Fedderlite manufacturing instructions and 

DUK920 - Fedderlite installation instructions. 

Roxsulation S - LPCB Ref. No 784a/01 

3. The system is approved with or without horizontal expansion joints in the render and insulation layer. 

4. The insulation boards are adhesively and mechanically fixed to the substrate with Dryvit Genesis adhesive, ribbon and dab method 

with a minimum of 8 dabs per full size board, and a minimum of 3 mechanical fixings per board. 

Outsulation & Outsulation Plus - LPCB Ref. No 784a/02 


66 20 Nov 2011



6. Dryvit EPS insulation boards adhered to the substrate with Dryvit Genesis adhesive. 

7. Minimum 100mm high continuous horizontal lamella fire breaks shall be affixed direct to the substrate with continuous band of Dryvit 

Genesis adhesive. The fire breaks shall be positioned at a maximum of 870mm above openings and a maximum of 3100mm centres 

between consecutive breaks. 

Fedderlite - LPCB Ref. No 985a/01 

8. Joints between Fedderlite panels are nominally 20mm wide and are filled with a 25mm closed cell polyethylene backer rod to produce 

a 10mm deep cavity to which an approved silicone sealant is applied. 

9. Fire breaks shall be incorporated as follows; 

a. Horizontal and vertical fire breaks are required around the perimeter of openings (top and sides only), these perimeter fire breaks 

consist of 100mm wide barrier adhered directly to the substrate with a continuous layer of Dryvit Genesis adhesive and shall be of 

sufficient thickness to create a tight fit between the panel face and substrate. 

b. Continuous horizontal cavity fire breaks consist of a 100mm high barrier bonded with Genesis adhesive to the substrate; these 

shall be positioned at a maximum of 850mm above openings and a maximum of 3320mm between subsequent horizontal breaks 

and shall be of sufficient thickness to create a tight fit between the panel face and substrate. 

c. Vertical fire breaks (external corners) consist of 100mm wide barriers located directly behind panels on external corner/edges, 

these vertical breaks are bonded with Genesis adhesive to the substrate and shall be of sufficient thickness to create a tight fit 

between the panel face and substrate. 

d. Vertical fire breaks (joints) consist of a 100mm wide barrier to span the joint, overlapping each panel edge by approximately 

40mm, and bonded directly to the substrate with a continuous layer of Dryvit Genesis adhesive. 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022h to LPS 1581: Issue 1 

Product Name 

RockShield 

External 

layer 

detail 

See 

Note 1 

Insulation 

material 

type & 

thickness 

(mm) 

Rockwool 

thickness 

range 30- 

150mm 

See note 2 

Cavity type & 

maximum depth 

(mm) 

Firebrakd 

detail 

EN 13501-1 


N/A Continuous No 

Performance 

Determined 

Cert. No. 

022h/01 

Notes: 

1. LPCB Ref. No. 022h/01 - RockShield base coat with universal reinforcing mesh with a white RockShield Silcoplast topcoat. 

2.. LPCB Ref. No. 022h/01 - RockShield insulation boards of nominally 1200mm x 600mm fixed to the masonry substrate using 4-5mm 

layer of RockShield adhesive mortar, and then mechanically fixed using TI anchors fixed at a rate of 5.56 per m². 

Sto Ltd 

2 Gordon Avenue, Hillington Park, Glasgow G52 4TG, United Kingdom 

Tel: +44 (0)141 892 8000 • Fax: +44 (0)141 404 9001 

E-mail: info.uk@stoeu.com • Website: www.sto.co.uk 

Certificate No: 749a to LPS 1581: Issue 2.0 

20 Nov 2011 67



Product Name 

External 

layer 

detail 

Insulation 

material type & 

thickness (mm) 

StoTherm Vario M See Note 1a EPS, thickness 

range 60- 

150mm see 

Note 2 

See Note 1b 


150mm See 

Note 2 

Cavity type & 

maximum depth 

(mm) 

A cavity of 

maximum of 10mm 

is formed between 

the EPS insulation 

and masonry 

substrate 

A cavity of 

Maximum of 10mm 

is formed between 

the EPS insulation 

and masonry 

substrate 

Firebreak 

detail 

See Note 3 

See Note 3 

EN13501-1 


No 

Performance 

Determined 

No 

Performance 

Determined 

Cert. No. 

749a/01 

749a/02 

Notes: 

1. 

a. LPCB Ref. No. 749a/01 - StoTherm EPS M Render, StoArmat Novo base coat with Sto Glass fibre Mesh F reinforcing mesh and 

Sto Stolit K2,0 top coat, natural or tinted with a PCS value of up to 2.36MJ/kg. A Secondary layer of Sto Glass fibre Mesh F 

reinforcing mesh is also required in any area that may be subject to flame impingement. 

b. LPCB Ref. No. 749a/02 - StoTherm EPS M Render, StoArmat Novo base coat with Sto Glass fibre Mesh F reinforcing mesh and 

Sto Stolit K2,0 top coat, natural or tinted with a PCS value of up to 2.36MJ/kg. 

2. LPCB Ref. No. 749a/01 & 749a/02 - StoTherm Vario M insulation boards of nominally 500mm x 500mm fixed to a mechanical rail 

system with PVC interlocking vertical T splines, the mechanical rails shall be fixed to the masonry substrate with Sto-Fixing Screw 

dowel UEZ8 085 CS fixings (or other suitable fixing ependant on masonry substrate type) at a maximum spacing of 300mm. The 

drainage cavity between the insulation and the masonry substrate is produced via the Sto aluminium starter track and horizontal PVC 

rails using Sto plastic shims. 

3. LPCB Ref. No. 749a/01 & 749a/02 - Sto Mineral Lamella Firebreak details as follows; 

a. 200mm high Sto Mineral Lamella fire break along top edge and sides of openings adhered direct to the masonry substrate with 

additional mechanical fixings(Sto Firebreak Dowel SS with integral head) at 300mm centres through the reinforcing mesh and 

firebreak into the masonry substrate. 

b. 200mm high continuous horizontal Sto Mineral Fibre Lamella fire break installed using a continuous layer of StoLevell-Uni 

adhesive, the fire break is additionally affixed with mechanical fixings (Sto SS fixing screw and washer) at 300mm centres through 

the reinforcing mesh and firebreak into the masonry substrate. Maximum spacing of continuous fire break; 1500mm above 

openings and maximum of 3000mm centres between consecutive breaks. 

Weber, Saint-Gobain Weber Limited 

Dickens House, Enterprise Way, Maulden Road, Flitwick, Bedfordshire MK45 5BY, United Kingdom 

Tel: +44 (0)8703 330070 • Fax: +44 (0)1525 718988 

E-mail: mail@netweber.co.uk • Website: www.netweber.co.uk 


Product Name 

Specification 

Thickness 

(mm) 

Insulation Material 

Fixing Method 

Maximum Vertical 

Firebreak Distance 

(m) 

Grade Insulation Material Cert. No. 

weber.therm XM (MFS) 50 - 170 Mechanical Continuous ETIC-1 Mineral fibre 796a/01 

Notes: 

1. Ref LPCB Ref. No. 796a/01, Insulation material mechanical fixings minimum of 4 ejotherm plastic head fixings per board and 

stainless steel fire fixings at 1/m 2 . 

2. Ref LPCB Ref. No. 796a/01, system available without top coat or with 6-8mm thick weber.rend PTC or PTS top coat, finish either 

scrape texture, dry-dash or primer and synthetic coating. 

68 20 Nov 2011


LPS 1581 RAIN SCREEN CLADDING SYSTEMS (RSC) ON MASONRY SUBSTRATES 



masonry face of a building 

The test method used is BS 8414-1:2002 Test method for non-load bearing external cladding systems applied 

to the face of the building and is representative of an external fire source or fully developed (post-flashover) 

fire in a room venting through an opening such as a window aperture that exposes the external surfaces of the 

cladding system to the effects of the impinging flames. The test method determines external and potential 

internal fire spread and, where a void exists, the extent of fire spread through the void. 

Rain Screen Cladding (RSC) systems are often used for the refurbishment of existing buildings where the 

insulation component is typically fixed to the original masonry face of the building. The external face of the 

cladding system is fixed to a supporting rail, so that the external face is spaced away from the insulation layer 

to form a cavity which may be drained. 

Sotech Limited 

2 Traynor Way, Whitehouse Business Park, Peterlee, County Durham SR8 2RU, United Kingdom 

Tel: +44 (0)191 587 2287 • Fax: +44 (0)191 518 0703 

E-mail: mail@sotech-optima.co.uk • Website: www.sotech-optima.co.uk 


Product Name 

Sotech Optima 

Rainscreen 

System 

External 

layer detail 

Aluminium 

cassette See 

Note 1 

Insulation 

material 

type & 

thickness 

(mm) 

75mm mineral 

fibre. See Note 

2 

Cavity 

type and 

maximum 

depth 

(mm) 

Cavity of maximum 200mm 

depth between rear of 

cassette system and face of 

insulation 

Firebreak 

detail 

See Note 

3 

EN 13501-1 


No Performance 

Determined 

Cert. 

No. 

770a/04 

Notes: 

1. LPCB Ref. No. 770a/04 - Sotech Optima Rainscreen cassette system consists of aluminium cassette panels precoated with pvdf to 

the following scope; 

Cassette Panel Material Cassette Height (mm) Max. Single Span* (mm) 

Aluminium 1.5mm 500 1500 

600 1500 

750 1500 

900 1350 

1100 1200 


600 1800 

750 1800 

900 1500 

1100 1200 


600 1800 

750 1800 

900 1600 

* Multiple spans are allowable provided that the intermediate supports are installed at centres not exceeding the maximum single 

span distances. 

2. LPCB Ref. No. 770a/04 - Insulation consists of Rainscreen Duo-slab Mineral fibre, 75mm thick and affixed through the sheathing 

board to the SFS with a minimum of one central stainless steel Ejot TID anchor (or similar specification) per slab plus one Ejot DH 

plastic anchor (or similar specification) at each slab end butt joint. 

20 Nov 2011 69


LPS 1581 RAIN SCREEN CLADDING SYSTEMS (RSC) ON MASONRY SUBSTRATES 

3. LPCB Ref. No. 770a/04 - fire breaks consist of a lamella/intumescent strip system located at a maximum height intervals of 2.5m. 

70 20 Nov 2011


LPS 1582 EXTERNAL CLADDING SYSTEMS SUPPORTED BY A STRUCTURAL STEELWORK FRAME 

LPS 1582 Requirements and tests for LPCB approval of non-load bearing external cladding systems fixed to 

and supported by a structural steel frame. 

20 Nov 2011 71


LPS 1582 EXTERNAL THERMAL INSULATED CLADDING (ETICS) SUPPORTED BY A STRUCTURAL 

STEEL FRAME 



This standard is applicable to non-load bearing external cladding systems, such as curtain walling, glazed 

elements, infill panels and insulated composite panel systems fixed to and supported by a structural steel 

frame. 

The test method used is BS 8414-2: 2005 Test method for non-load bearing external cladding systems fixed 

to and supported by a structural steel frame, and is intended to represent the action of a fully developed (post 

flashover) fire in a room venting through an opening such as a window aperture, or an external fire source that 

exposes the external surfaces of the cladding system to the effects of the impinging flames. The test method 

determines external and potential internal and fire spread and, where a void exists, the extent of fire spread 

through the void. 

Dryvit UK Limited 

Unit 4, Wren Park, Hitchin Road, Shefford, Bedfordshire SG17 5JD, United Kingdom 

Tel: +44 (0)1462 819555 • Fax: +44 (0)1462 819556 

E-mail: ukenquiries@dryvit.com • Website: www.dryvit.co.uk 

Certificate No: 784b to LPS 1582 Issue 1 

Product 

Name 

Outsulation & 

Outsulation 

Plus 

Outsulation 

Rail 

Fedderlite 

Panel System 

External 

layer 

detail 

See Note 

1& 4 

See Note 

1& 7 

See Note 

1 & 10 

Insulation 

material 

type & 

thickness 

EPS Thickness 

range 50- 

250mm See 

Note 5 

EPS Thickness 

range 50- 

250mm See 

Note 8 

EPS Thickness 

range 50- 

120mm 

Frame 

type 

& 

sheathing 

board 

See Note 

2 

See Note 

2 

See Note 

2 

Cavity 

type and 

maximum 

depth 

No cavity 

Drainage cavity of 

maximum 15mm depth 

between sheathing board 

and fire break 

Encapsulated Cavity 

between sheathing board 

and rear of Fedderlite 

panel 

Firebreak 

detail 

See Note 

6 

See Note 

9 

See Note 

11 

EN 13501-1 


B-s2-d0 

See Note 1 

B-s2-d0 

See Note 1 

B-s2-d0 

See Note 1 

Cert. 

No. 

784b/01 

784b/02 

985b/01 

Notes: 

General. 

1. LPCB Ref. No. 784b/01, 784b/02 & 985b/01 - Approved systems consist of Dryvit Genesis base coat, Dryvit Standard Plus reinforcing 

mesh, with or without Dryvit primer and a Dryvit Quarzputz PMRB, Sandpebble PMRB or Sandpebble Fine PMRB top coat, natural or 

tinted with a Qpcs value of up to 2.95MJ/kg. 

The stated EN 13501-1 classification is applicable to systems with a PMRB top coat, natural or tinted with a Qpcs value up to 

2.63MJ/kg only. 

2. LPCB Ref. No. 784b/01, 784b/02 & 985b/01 - Any galvanised steel frame system, installed between floor slabs, confirmed by 

structural assessment to maintain the structural stability of the wall system in ambient conditions, and is suitable for the fire 

performance of the wall when exposed to fire within the building. The studs must have a minimum leg length of 45mm and be spaced 

at a maximum of 600mm centres (the stud size as tested was 100mm x 45mm x 1.2mm). The frame shall be clad with any sheathing 

board system suitable for the application on the external (cladding) face of the following generic types:- cement particle board (min. 

12mm thick), cement-based calcium silicate board (min. 9mm thick), calcium silicate board (min. 9mm thick) or magnesium oxide 

board (min. 9mm thick). The system is approved with or without mineral wool insulation within the steel frame stud cavity. The internal 

face frame shall be clad with any type of gypsum wallboard that ensures that the required reaction-to-fire and fire resistance 

performance is provided when the wall is exposed to fire within the building. 

3. Subject to the stated conditions the Outsulation & Outsulation Plus systems (LPCB Ref. No. 784b/01) shall be installed in accordance 

with the application detail contained within Dryvit documents DUK204 (21/01/08) and DUK218 (V1 21-2-07) respectively. The 

Outsulation Rail system (LPCB Ref. No. 784b/02) shall be installed in accordance with the application detail contained within Dryvit 

document DUK664 (21-08-07) and the Fedderlite panel system (LPCB Ref. No. 985b/01) shall be installed in accordance with the 

72 20 Nov 2011



STEEL FRAME 

application detail contained within Dryvit document DUK217 Issue 003 31/01/11 - Fedderlite manufacturing instructions and DUK920 

- Fedderlite installation instructions. See BRE Assessment CC270532 for scope of components and variations. 

Outsulation & Outsulation Plus - LPCB Ref. No 784b/01 


5. Dryvit EPS insulation boards adhered to the sheathing board with Dryvit Genesis adhesive. 

6. Minimum 100mm high continuous horizontal lamella fire breaks shall be affixed direct to the sheathing board with continuous band of 

Dryvit Genesis adhesive. The fire breaks shall be positioned at a maximum of 870mm above openings and a maximum of 3100mm 

centres between consecutive breaks. 

Outsulation Rail - LPCB Ref. No 784b/02 


8. Dryvit EPS insulation boards fixed to a mechanical PVC ‘T’ spline railing system. The rails are fixed to the sheathing board using 

packing shims of up to 15mm thick at 300mm centres with suitable fixings to form the drainage cavity. 

9. The cavity fire break system and continuous horizontal lamella fire breaks shall be positioned a maximum of 800mm above openings, 

subsequent fire breaks shall be positioned at each floor slab at a maximum spacing of 3100mm centres. 

Fedderlite - LPCB Ref. No 985b/01 

10. Joints between Fedderlite panels are nominally 20mm wide and are filled with a 25mm closed cell polyethylene backer rod to produce 

a 10mm deep cavity to which an approved silicone sealant is applied. 

11. Fire breaks shall be incorporated as follows; 

a. Horizontal and vertical fire breaks are required around the perimeter of openings (top and sides only), these perimeter fire breaks 

consist of 100mm wide barrier adhered directly to the sheathing board with a continuous layer of Dryvit Genesis adhesive and 

shall be of sufficient thickness to create a tight fit between the panel face and substrate. 

b. Continuous horizontal cavity fire breaks consist of a 100mm high barrier bonded with Genesis adhesive to the sheathing board; 

these shall be positioned at a maximum of 850mm above openings and a maximum of 3320mm between subsequent horizontal 

breaks and shall be of sufficient thickness to create a tight fit between the panel face and substrate. 

c. Vertical fire breaks (external corners) consist of 100mm wide barriers located directly behind panels on external corner/edges, 

these vertical breaks are bonded with Genesis adhesive to the sheathing board and shall be of sufficient thickness to create a 

tight fit between the panel face and substrate. 

d. Vertical fire breaks (joints) consist of a 100mm wide barrier to span the joint, overlapping each panel edge by approximately 

40mm, and bonded directly to the sheathing board with a continuous layer of Dryvit Genesis adhesive. 

Sto Ltd 

2 Gordon Avenue, Hillington Park, Glasgow G52 4TG, United Kingdom 

Tel: +44 (0)141 892 8000 • Fax: +44 (0)141 404 9001 

E-mail: info.uk@stoeu.com • Website: www.sto.co.uk 

Certificate No: 749b to LPS 1582: Issue 1.0 

20 Nov 2011 73



STEEL FRAME 

Product Name 

StoTherm Vario M 

StoTherm Mineral M 

External 

layer 

detail 

See 

Note 1 

See 

Note 5 

Insulation 

material 

type & 

thickness 

(mm) 

EPS, 

thickness 

range 60- 

150mm 

See Note 

2 

Mineral 

fibre, 

thickness 

range 60- 

150mm 

See Note 

6 

Frame 

type and 

sheathing 

board 

See Note 

3 

See Note 

7 

Cavity 

type & 

maximum 

depth 

(mm) 

Drainage 

cavity of 

maximum 

20mm 

depth 

between 

sheathing 

board and 

insulation 

Drainage 

cavity of 

maximum 

20mm 

depth 

between 

sheathing 

board and 

insulation 

Firebreak 

detail 

See Note 

4 

See Note 

8 

EN13501-1 


No 

Performance 

Determined 

No 

Performance 

Determined 

Cert. No. 

749b/01 

749b/02 

Notes: 

1. LPCB Ref. No. 749b/01 - StoTherm EPS M Render, StoArmat Novo base coat with Sto Glass fibre Mesh F reinforcing mesh and Sto 

Stolit K2,0 top coat, natural or tinted with a PCS value of up to 2.36MJ/kg. A Secondary layer of Sto Glass fibre Mesh F reinforcing 

mesh is also required in any area that may be subject to flame impingement. 

2 LPCB Ref. No. 749b/01 - StoTherm Vario M insulation boards of nominally 500mm x 500mm fixed to a mechanical rail system with 

PVC interlocking vertical T splines, the mechanical rails shall be fixed to the sheathing board with Sto-Screw fixings, CS self-tapping 

5.5 x 50mm screw fixings at a maximum spacing of 300mm. The drainage cavity between the insulation and the sheathing board is 

produced via the Sto aluminium starter track and horizontal PVC rails using Sto plastic shims. 

3. METSEC lightweight steel frame installed between floor slabs. The frame is clad with two layers of 12.5mm British Gypsum Gyproc 

Fireline wallboard on the internal face and 12mm Versapanel sheathing board on the external (cladding) face, the sheathing board is 

fixed to the stud sections using Euroform EMF 1 5.5 x 50mm fixings at a maximum of 600mm centres. 

4. LPCB Ref. No. 749b/01 - StoTherm Mineral M Firebreak details as follows; 

a. 200mm high Sto Mineral Lamella fire break along top edge and sides of openings adhered direct to the sheathing board with 

additional mechanical fixings (Sto SS fixing screw and washer) at 300mm centres through the reinforcing mesh and firebreak into 

the sheathing board. 

b. 200mm high continuous horizontal Sto Mineral Fibre Lamella fire break installed using Sto 2 part stainless steel Fire Break Rails 

which are screwed back to the sheathing board with Sto intumescent strip on lower edge rail, the fire break is additionally affixed 

with mechanical fixings (Sto SS fixing screw and washer) at 300mm centres through the reinforcing mesh and firebreak into the 

sheathing board. Maximum spacing of continuous fire break; 1500mm above openings and maximum of 2700mm centres 

between consecutive breaks. 

5. LPCB Ref. No. 749b/02 - StoTherm Mineral M Render, StoArmat Classic base coat with Sto glass fibre Mesh F reinforcing mesh and 

Sto Stolit K2,0 top coat, natural or tinted with a PCS value of up to 2.36MJ/kg. 

6. LPCB Ref. No. 749b/02 - StoTherm Mineral M insulation boards of nominally 500mm x 500mm fixed to a mechanical rail system with 

PVC interlocking vertical T splines, the mechanical rails shall be fixed to the sheathing board with Sto-Screw Rail CS 5.5 x 50 fixings 

at a maximum spacing of 300mm. The drainage cavity between the insulation and the masonry substrate is produced via the Sto 

aluminium starter track and horizontal PVC rails using Sto plastic shims. 

7. LPCB Ref. No. 749b/02 - METSEC lightweight steel frame installed between floor slabs. The frame is clad with two layers of 12.5mm 

British Gypsum Gyproc Fireline wallboard on the internal face and 12mm Versapanel sheathing board on the external (cladding) face, 

the sheathing board is fixed to the stud sections using Euroform EMF 1 5.5 x 50mm fixings at a maximum of 600mm centres. 

8. LPCB Ref. No. 749b/02 - StoTherm Mineral M Firebreak details as follows; 

a. 200mm high Sto Mineral Lamella fire break along top edge and sides of openings adhered direct to the sheathing board. 

b. 500mm high continuous horizontal Sto Mineral Fibre board fire break installed using Sto 2 part stainless steel Fire Break Rails 

which are screwed back to the sheathing board with Sto intumescent strip on lower edge rail. Maximum continuous fire break 

spacing; 1450mm above openings and maximum of 3000mm between consecutive breaks. 

74 20 Nov 2011


LPS 1582 RAIN SCREEN CLADDING SYSTEM (RSC) SUPPORTED BY A STRUCTURAL STEEL FRAME 



This standard is applicable to non-load bearing external rain screen cladding systems fixed to and supported 

by a structural steel frame. 

The test method used is BS 8414-2: 2005 Test method for non-load bearing external cladding systems fixed 

to and supported by a structural steel frame, and is intended to represent the action of a fully developed (post 

flashover) fire in a room venting through an opening such as a window aperture, or an external fire source that 

exposes the external surfaces of the cladding system to the effects of the impinging flames. The test method 

determines external and potential internal and fire spread and, where a void exists, the extent of fire spread 

through the void. 



Tel: +44 (0)191 587 2287 • Fax: +44 (0)191 518 0703 


Certificate No: 770b to LPS 1582 Issue 1.0 

Product Name 

Sotech Optima 

Rainscreen 

System 

External 

layer 

detail 

Aluminium 

cassette see 

Note 1 

Insulation 

material 

type & 

thickness 

100mm 

mineral fibre 

see Note 2 

Frame 

type & 

boarding 

See Note 

3 

Cavity type 

and 

maximum 

depth (mm) 

Cavity of maximum 

120mm depth between 

rear of cassette system 

and face of insulation 

Firebreak 

detail 

See Note 

4 

EN 13501-1 


No Performance 

Determined 

Cert. 

No. 

770b/01 

Notes: 

1. LPCB Ref. No. 770b/01 - Sotech Optima Rainscreen cassette system consists of aluminium cassette panels precoated with 

pvdf to the following scope; 

Cassette Panel Material Cassette Height (mm) Maximum Single 

Span*(mm) 

Aluminium 1.5mm 

500 1500 

600 1500 

750 1500 

900 1350 

1100 1200 


500 1800 

600 1800 

750 1800 

900 1500 

1100 1200 


500 1800 

600 1800 

750 1800 

900 1600 

*Multiple spans are allowable provided that the intermediate supports are installed at centres not exceeding the maximum 

single span distances. 

2. LPCB Ref. No. 770b/01 – Insulation consists of Rainscreen Duo-slab Mineral fibre, 100mm thick and affixed through the 

sheathing board to the SFS with a minimum of one fixing (Ejot 80 SS disc washer T1D-TR2 secured with JT3-D6H screw 5.5- 

6.3x147 and HTV-4055 washer) per slab. 

3. LPCB Ref. No. 770b/01 – Frame system consists of METSEC SFS 150mm lightweight steel frame stud and track sections 

installed between floor slabs. External sheathing board; minimum of single layer 12mm Versapanel fixed at 600mm centres. 

Internal liner; minimum of two layers 12.5mm British Gypsum Gyproc Fireline boards, staggered lay and fixed at 600mm 

centres. The cavity within the SFS is unfilled. 

4. LPCB Ref. No. 770b/01 - Fire breaks consist of a horizontal lamella/intumescent strip system located at a maximum height 

intervals of 2.5m. 

20 Nov 2011 75


ROOFING PRODUCTS 

The products listed in this section are used as roofing systems where there is a risk of fire as follows; 

Section 2.5.1 - Protection against fire from outside the building. 

Section 2.5.2 - Protection against fire form inside the building. 

76 20 Nov 2011


PROTECTION AGAINST FIRE FROM OUTSIDE THE BUILDING 

The products listed in this section are used as roofing systems that offer protection where there is a risk of fire 

from outside of the building. The products have been tested against either BS 476:Part 3 Fire tests on building 

materials & structures - external fire exposure roof test or ENV 1187:2002 Test methods for external fire 

exposure to roofs, in order to ensure that roof covering and its supporting deck act as a protective barrier 

against fire from the outside of a building. It should be noted that BS 476: Part 3:1958 has been withdrawn, 

but is still referred to in Approved Document B of the UK Building Regulations. ENV 1187:2002 has been 

issued as a Draft for Development publication and is of a provisional nature as agreement could not be 

reached on the publication of an EN. 

Work is currently being undertaken to develop a Loss Prevention Standard for this product group. 

Icopal Limited 

Barton Dock Road, Stretford, Manchester M32 0YL, United Kingdom 

Tel: +44 (0)161 865 4444 • Fax: +44 (0)161 865 8433 

E-mail: info@icopal.com • Website: www.icopal.co.uk 

Certificate No: 572a to BS 476: Part 3: 1958 

Firesmart 

Product Name Category Cert. No. 

Firesmart Proflex system EXT.F.AA 572a/01 

Firesmart Power system EXT.F.AA 572a/03 

Firesmart Tecnotorch system EXT.F.AA 572a/05 

Firesmart Profiles XL system EXT.F.AA 572a/07 

Firesmart Thermaweld EXT.F.AA 572a/09 

Notes: 

1. The categories specified are applicable only to roofs having a pitch of 10 degrees or less. 

2. All products were tested using a 19mm exterior grade plywood deck. 

Certificate No: 572b to ENV 1187: 2002 Test 1 

ENV 1187: 2002 Test 1 


Firesmart Proflex system EXT.F.AA 572b/01 

Firesmart Power system EXT.F.AA 572b/03 

Firesmart Tecnotorch system EXT.F.AA 572b/05 

Firesmart Profiles XL system EXT.F.AA 572b/07 

Firesmart Thermaweld EXT.F.AA 572b/09 

Notes: 

1. The certification applies to roofs with a pitch of 20 degrees or less. 

2. The certification for 572b/01, 572b/03, 572b/07 and 572b/09 covers the systems when applied to any wooden continuous deck with a 

minimum thickness of 16mm, and with gaps not exceeding 0.5mm and any non-combustible continuous deck with a minimum 

thickness of 10mm. 

3. The certification for 572b/05 covers the systems when applied to a 19mm thick exterior grade plywood deck only. 

4. The performance of the systems is detailed in the following tables. 

20 Nov 2011 77



Firesmart Proflex 

Firesmart Power 

Firesmart Tecnatorch 

Firesmart Profiles XL 

Firesmart Thermaweld 

Specimen 

1 2 3 4 1 2 3 4 1 2 3 4 

Ext ernal f ire sp read 

Time taken to 

travel: (in an 

upwards 

direction from 

upper edge of 

the brand) 

(min:sec) 

Time taken to 

travel: (in a 

downwards 

direction from 

lower edge of 

the brand) 

(min:sec) 

10cm - - - - - - - - - - - - 

30cm - - - - - - - - - - - - 

50cm - - - - - - - - - - - - 

70cm - - - - - - - - - - - - 

to upper edge 

of measuring 

zone 

- - - - - - - - - - - - 

10cm 3:29 - 2:33 2:19 2:59 - 2:57 2:06 - - - - 

30cm - - - - - - - - - - - - 

50cm - - - - - - - - - - - - 

to lower edge 

of measuring 

zone 

F alling f laming mat erial 

f ro m surf ace o f ro o f 

- - - - - - - - - - - - 

Time of occurrence (min:sec) 

Length of time burning on floor 

(min:sec) 

B urnt leng t h ( ext ernal) 

Upwards (cm) 

Downwards (cm) 

Damaged area (cm 2 ) 

- - - - - - - - - - - - 

- - - - - - - - - - - - 

0 0 0 0 0 0 0 0 0 0 0 0 

19 5 21 11 12 5 13 14 6 7 6 7 

548 698 554 587 650 697 576 647 645 574 601 557 






Specimen 

1 2 3 4 1 2 3 4 1 2 3 4 

F ire p enet rat io n 

Falling flaming 

material from 

underside: 

Time of 

occurrence 

(min:sec) 

Length of time 

burning on floor 

(min:sec) 

Time of 

occurrence 

(min:sec) 

- - - - - - - - - - - - 

- - - - - - - - - - - - 

- - - - - - - - - - - - 

Nature - - - - - - - - - - - - 

Openings 

Fire penetration 

M aximum area 

of a single 

opening (cm2) 

Sum of area of 

all openings 

(cm2) 

Time of 

occurrence 

(min:sec) 

- - - - - - - - - - - - 

- - - - - - - - - - - - 

- - - - - - - - - - - - 

Nature - - - - - - - - - - - - 

78 20 Nov 2011








Specimen 

1 2 3 4 1 2 3 4 1 2 3 4 

Int ernal d amag e 

Non-flaming 

propogation 

Nature - - - - - - - - - - - - 

Extent of 

internal damage 

(cm2) 

Upwards 0 0 0 0 0 0 0 0 0 0 0 0 

Downwards 19 5 21 11 12 5 13 14 6 7 6 7 

Layer 1: 

Upwards 0 0 0 0 0 0 0 0 0 0 0 0 

Downwards 19 5 21 11 12 5 13 14 6 7 6 7 

Layer 2: 

M aximum length 

of burnt material 

in each 

functional layer 

(cm2) 

Upwards 0 0 0 0 0 0 0 0 0 0 0 0 

Downwards 19 5 21 11 12 5 13 14 6 7 6 7 

Layer 3: 

Upwards 0 0 0 0 0 0 0 0 0 0 0 0 

Downwards 19 5 21 11 12 5 13 14 0 0 0 0 

Layer 4: 

Upwards 0 0 0 0 0 0 0 0 N/A N/A N/A N/A 

Downwards 0 0 0 0 0 0 0 0 N/A N/A N/A N/A 

Layer 1 548 698 554 587 650 697 576 647 645 574 601 587 

Damaged area 

of each 

functional layer 

(cm2) 

Layer 2 548 698 554 587 650 697 576 647 645 574 601 587 

Layer 3 548 698 554 587 650 697 576 647 98 288 82 159 

Ext ent o f lat eral f lame 

sp read 

Layer 4 200 181 246 210 212 70 276 481 N/A N/A N/A N/A 

External (cm) 

Internal (cm) 

Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil 

Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil Nil 

IKO PLC 

Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB, United Kingdom 

Tel: +44 (0)844 412 7207 • Fax: +44 (0)844 412 7208 

E-mail: technical@ikogroup.co.uk • Website: www.ikogroup.co.uk 


Roofing Products 


Coolbond FireBLOC System EXT.F.AA 626a/01 

Superflex FireBLOC system EXT.F.AA 626a/06 

Superflex FireBLOC T-O system EXT.F.AA 626a/07 

20 Nov 2011 79




Ultra prevENt system EXT.F.AA 626a/08 

Ultra prevENt T-O system EXT.F.AA 626a/10 

Goldseal FR Roofing System EXT.F.AA 626a/11 

Goldseal Torch On Roofing System EXT.F.AA 626a/12 

Mach One Single Layer (Cold Adhered) Roofing System EXT.F.AA 626a/14 

Mach One Single Layer (Mechanically Fixed) Roofing System EXT.F.AA 626a-13 

Notes: 

1. All systems specified are applicable only to roofs having a pitch of 10 degrees or less. 

2. All systems specified were tested applied to an 18mm exterior grade plywood deck. 

3. The supporting substrate may be reinforced (cast insitu) concrete 200mm or pre cast concrete slabs, (screeded), 50-100 mm 

screeded Woodwool slabs, profiled metal decking or 20mm timber boards. 

4. Systems LPCB Ref. No. 626a/07 Superflex FireBLOC T-O consist of any IKO VCL, Insulation layers Supertherm Universal (53- 

103mm), or Supertherm PIR (50-100mm), or SuperRock standard (100-160mm) and IKO Systems T-O underlay. 

5. Systems LPCB Ref. No. 626a/06 Superflex FireBLOC consist of any Superbar FireBLOC VCL, Insulation layers Supertherm 

Universal (53-103mm), or Enertherm PIR (50-100mm), or SuperRock standard (100-160mm) and Superbase FireBLOC underlay. 

6. Systems LPCB Ref. No. 626a/08 Ultra prevENt consist of any IKO Systems VCL, Insulation layers Supertherm Universal (53- 

103mm), or Enertherm PIR (50-100mm), or SuperRock standard (100-160mm) and UltraprevENt underlay. 

7. Systems LPCB Ref. No. 626a/10 Ultra prevENt T-O consist of any Superbar FireBLOC VCL, Insulation layers Supertherm Universal 

(53-103mm), or Supertherm PIR (50-100mm), or SuperRock standard (100-160mm) and Ultra prevENt T-O underlay. 

8. The requirements for BS476: Part 3: 1958 will cease when the UK Building Regulations cease to refer to it. 

Certificate No: 626b to DD ENV 1187: 2002 - Test Methods for External Fire Exposure to Roofs - Test 1 


Product Name 

Cert. No. 

Coolbond FireBLOC system 626b/01 

Notes: 

1. The certification applies to roofs with a pitch of 20 degrees or greater. 

2. The certification covers the above systems when applied to a 18mm thick exterior grade plywood deck. 

3. The performance of the systems is detailed in the following table. 

Time taken to travel: 

(in an upw ards 

direction from upper 

edge of the brand) 

(min:sec) 

Time taken to travel: 

(in a dow nw ards 

direction from low er 

edge of the brand) 

(min:sec) 

Specimen 

External fire spread 

10cm 

30cm 

50cm 

70cm 

to upper edge of 

measuring zone 

10cm 

30cm 

50cm 

to low er edge of 

measuring zone 

Falling flaming material from surface 

of roof 

Time of occurrence (min:sec) 

Length of time burning on floor (min: sec) 

Burnt length (external) 

Upw ards (cm) 

Dow nw ards (cm) 

Damaged area (cm 2 ) 

1 2 3 4 

_ 

_ 

_ 

_ 

_ 

1:56 

2:30 

_ 

_ 

Coolbond FireBLOC system 

_ 

_ 

_ 

_ 

_ 

1:25 

2:17 

_ 

_ 

5:59 

_ 

_ 

_ 

_ 

1:49 

2:28 

_ 

_ 

_ 

_ 

_ 

_ 

_ 

1:54 

5:05- 

_ 

- - - - 

- - - - 

2 3 10 0 

30 30 30 30 

700 600 700 800 

_ 

80 20 Nov 2011



Specimen 


1 2 3 4 


Time of occurrence 

(min:sec) - - - - 

Falling flaming 

material from 

underside: 

Length of time 

burning on floor 

(min:sec) 

- - - - 


(min:sec) - - - - 

Nature 

Maximum area of a 

single opening 

(cm 2 ) 

- - - - 

Sum of area of all 

openings 

(cm 2 ) 

- - - - 

Openings 

- - - - 


(min:sec) - - - - 


Nature 

- - - - 

20 Nov 2011 81



Specimen 

Internal damage 

Non-flaming 

propagation Extent of 

internal damage 

(cm) 

1 2 3 4 

Nature _ _ _ _ 

Upwards 

Downwards 

Layer 1: 

Upwards 

Downwards 


_ 

19 

_ 

19 

_ 

18 

_ 

18 

_ 

28 

_ 

28 

_ 

27 

_ 

27 

Maximum length 

of burnt material 

in each functional 

layer (cm) 

Layer 2: 

Upwards 

Downwards 

_ 

8 

_ 

18 

_ 

16 

_ 

27 

Layer 3: 

Updwards 

Downwards 

_ 

8 

_ 

5 

_ 

5 

_ 

16 

Damaged area of 

each functional 

layer 

(cm2) 

Layer 1 

Layer 2 

Layer 3 

700 

500 

400 

500 

500 

500 

700 

600 

500 

700 

700 

600 

Extent of lateral flame spread 

External (cm) 

Internal (cm) 

Nil Nil Nil Nil 

Nil Nil Nil Nil 

Certificate No: 626c to DD ENV 1187: 2002 Test 2 


Product Name 

Cert. No. 

Coolbond FireBLOC system 626c/01 

Notes: 

1) The certification applies to roofs with any pitch. 

2) The certification covers the above systems when applied to a 18mm thick exterior grade plywood deck. 

3) The performance of the systems is detailed in the following tables. 

626c/01 Coolbond FireBLOC system 

Specimen 1 2 3 4 5 6 Average 

Air velocity 2 m/s 2 m/s 2 m/s 4 m/s 4 m/s 4 m/s N/A 

Time at which specimen ignited 00:54 00:51 00:50 00:48 00:38 00:41 00:47 

(min:sec) 

Time at which flaming of specimen 08:53 08:49 04:29 04:56 04:15 04:10 05:55 

ceased (min:sec) 

Time at which glowing of specimen N/A N/A N/A N/A N/A N/A - 

ceased (min:sec) 

Test termination time (min:sec) 15:00 15:00 15:00 15:00 15:00 15:00 15:00 

Reason for termination (if applicable) N/A N/A N/A N/A N/A N/A - 

Extent of damage to roof covering 360 360 410 385 390 360 378 

Extent of damage (mm) to substrate (mm) 0 0 0 0 0 0 0 

Damaged area of roof covering (mm2) 31000 31000 36000 34000 34500 32000 33084 

Damaged area of substrate (mm2) 0 0 0 0 0 0 0 

Maximum depth of damage (mm) 3 3 3 3 3 3 3 

82 20 Nov 2011



Permanite Asphalt 

Cawdor Quarry, Matlock, Derbyshire DE4 2JH, United Kingdom 

Tel: +44 (0)1629 582213 • Fax: +44 (0)1629 583375 

E-mail: roof.tech@permanite.com • Website: www.permanite.com 


Permaphalt 


Permaphalt Category EXT.F.AA 666a/01 

Notes: 

1. The Categories specified are applicable only to roofs having a pitch of 10 degrees or less. 

2. The test specimen had 2 layers of Permaphalt to a total thickness of 20mm. 

3. The product was tested separately with 90mm thick Supertherm PIR and 135mm thick Rockwool HD insulation board. 

4. All tests used a 18mm exterior grade plywood deck. 

5. The requirement for BS476: Part 3: 1958 will cease when the Building Regulations cease to refer to it. 

20 Nov 2011 83


PROTECTION AGAINST FIRE FROM INSIDE THE BUILDING 

The products listed in this section are built-up roofing systems which offer protection against the risk of fire 

from within the building. The products have been tested to: 

 

or 

 

or 

 

or 

 

BS 476:Part 21 Fire tests on building materials & structures. Methods for determination of the fire 

resistance of loadbearing elements of construction 

BS 476:Part 22 Fire tests on building materials & structures. Methods for determination of the fire 

resistance of non-loadbearing elements 

EN 1364:Part 2 Fire resistance tests for non-loadbearing elements. Ceilings 

EN 1365:Part 2 Fire resistance tests for loadbearing elements. Floors & roofs and meet the 

requirements of LPS 1208 for fire resistance (For roof sandwich panels, see Section 2.2.) 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022a to BS 476: Part 21: Method 7 (see note 1) 

Product Name 

Specification 

System 

Thickness 

(mm) (1) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Core 

Material 

Cert. No. 

Hardrock DD roofing board 210 120 120 Stone Wool 022a/01 

100 - 135 60 60 Stone Wool 

140 - 205 90 90 Stone Wool 

Hardrock DD SPA roofing board 210 120 120 Stone Wool 022a/02 

100 - 135 60 60 Stone Wool 

140 - 205 90 90 Stone Wool 

DuoRock roofing board 100 - 210 60 60 Stone Wool 022a/03 

Note: 

1. Roof board system LPCB Ref No. 022a/01 & LPCB Ref No. 022a/03: Mechanically fastened Sarnafil single ply type S327-12EL 

(1.2mm thickness), external weather proof membrane (or alternative membrane less than 3.5 kg/m² e.g. PVC, Chlorinated PE, Butyl 

Rubber with welded seams); 

Comprising of two layers of Rockwool roofing board with staggered joints (100mm minimum stagger for fire resistance up to 90 

minutes and 300mm stagger for 2 hours fire resistance), vapour control layer and 0.7mm thickness 35mm deep profile steel metal 

deck. 

Roof board system LPCB Ref No. 022a/02: Sarnafil single ply external weather proof membrane type G410-12EL (1.2mm thickness), 

fully adhered to Hardrock DD SPA roof board system with Sarnifil Adhesive(or Rockwool approved alternative adhesive/membrane 

combination, with a membrane material less than 3.5 kg/m² e.g. PVC, Chlorinated PE, Butyl Rubber with welded seams); comprising 

of two layers of Rockwool roofing board with staggered joints (100mm minimum stagger for fire resistance up to 90 minutes and 

300mm stagger for 2 hours fire resistance), vapour control layer and 0.7mm thickness 35mm deep profile steel metal deck. 

The test construction was tested unloaded. However, deflection of the roof did not exceed the allowable limits set out in BS 476: Part 

20: 1987 for loadbearing horizontal elements. Decking side laps were stitched at 450mm centres. 

Roof Board System LPCB Ref No 022a/01, 022a/02 & 022a/03 Hardrock DD, Hardrock DD SPA and DuoRock roofing boards are 

also available and approved in cut-to-fall tapered options, the relevant minimum & maximum system thickness and staggered joints 

shall apply as detailed above. 

84 20 Nov 2011


REACTION TO FIRE (RTF) CLASSIFICATIONS FOR MATERIALS AND PRODUCTS 

The materials and products listed in this section are LPCB approved and classified to one of the following 

Reaction to Fire (RTF) classification systems: 

 

Non-combustible to BS 476-4 Fire tests on building materials and structures. Non-combustibility test 

for materials. 

Class O as defined in Approved Document B - Fire Safety, The Building Regulations 2000. 

 

BS EN 13501-1 Fire classification of construction products and building elements. Classification using 

test data from reaction to fire tests. Note: LPCB approvals under this standard are limited to materials 

or products resulting in a classification of A1, A2 or B. Products under A2 or B will also be classified in 

relation to the additional classifications of s and d (eg s3, d2). 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022e to EN 13501-1: 2002 

Rockwool Non-combustible Insulation Materials 

Product Name 

Thickness 

(mm) 

Test/Assessment 

Standard 

Classification Cert. 

No. 

Cladding Roll - Aluminium Foil Faced 60 - 180 EN 13501-1: 2002 A1 022e/01 

Cladding Roll - Unfaced 60 - 180 EN 13501-1: 2002 A1 

Cladding Roll - White Tissue Faced 60 - 180 EN 13501-1: 2002 A1 

Cavity Batts - Unfaced 50 - 150 EN 13501-1: 2002 A1 022e/02 

Rainscreen Duo Slabs - Black Tissue Faced 50 - 125 EN 13501-1: 2002 A1 022e/03 

Rainscreen Duo Slabs - Unfaced 50 -125 EN 13501-1: 2002 A1 

Flexi Batts - Unfaced 50 - 150 EN 13501-1: 2002 A1 022e/04 

Hardrock Dual Density Roofing Boards - Black Tissue 50 - 155 EN 13501-1: 2002 A1 022e/05 

Faced 

Hardrock Dual Density Roofing Boards - Unfaced 50 - 155 EN 13501-1: 2002 A1 

Hardrock Dual Density Roofing Boards - White Tissue 50 - 155 EN 13501-1: 2002 A1 

Faced 

DuoRock Roofing Boards - Black Tissue Faced 50 - 180 EN 13501-1: 2002 A1 022e/06 

DuoRock Roofing Boards - Unfaced 50 - 180 EN 13501-1: 2002 A1 

DuoRock Roofing Boards - White Tissue Faced 50 - 180 EN 13501-1: 2002 A1 

Superglass Insulation Limited 

Thistle Industrial Estate, Kerse Road, Stirling FK7 7RW, United Kingdom 

Tel: +44 (0)1786 451170 • Fax: +44 (0)1786 451245 

E-mail: technical@superglass.org.uk • Website: www.superglass.co.uk 

Certificate No: 472a to BS 476: Part 4 

Thermaquilt and Superglass Cladding Mat 

Product Name 

Thickness Test/Assessment 

Classification Cert. No. 

(mm) 

Standard 

Thermaquilt 50 - 200 BS 476:Part 4 Non-combustible 472a/01 

Superglass Cladding Mat 60 - 200 BS 476:Part 4 Non-combustible 472a/02 

20 Nov 2011 85


LPS 1132 WALL & FLOOR PENETRATION AND LINEAR GAP SEALS 

The following products have been approved to LPS 1132 Requirements and tests for LPCB approval of wall & 

floor penetration & linear gap seals to help ensure fire resisting compartment walls and floors are not 

compromised by the installation of building services that pass between fire resisting compartments. 

The design requirements for these products are described in more detail in Section 4.6 of the LPC Design 

Guide for the Fire Protection of Buildings: 2000. 

DST Group Ltd 

Design House, 2C Southgate, White Lund, Morecombe, Lancs LA3 3PB, United Kingdom 

Tel: +44 (0)1524 389494 • Fax: +44 (0)1524 389495 

E-mail: sales@dstgroup.co.uk • Website: www.dstgroup.co.uk 


Fire Sleeve Pipe Wraps 

Product 

Use 

Name 

Fire Sleeve 

Pipe Wraps 

uPVC Pipes up to 167mm 

diameter 

uPVC Pipes from 167mm to 

225mm diameter 

ABS pipes up to 114mm 

diameter 

Polypropylene pipes up to 

16mm diameter 

Polypropylene pipes from 

16mm to 160 mm diameter 

Polypropylene pipes from 

160mm to 225mm diameter 

Polyethylene pipes up to 

225mm diameter 

Steel pipes up to 220mm 

diameter 

Copper pipes up to 76mm 

diameter 

Element of 

construction 

Concrete, masonry 

or drywall 


or drywall 


or drywall 


or drywall 


or drywall 


or drywall 


or drywall 


or drywall 


or drywall 

Element of 

construction 

thickness 

minimum 

(mm) 

Fire 

resistance 

(min) 

Integrity 

Fire 

resistance 

(min) 

Insulation 

Cert. 

No. 

130 120 Not assessed 873a/01 

130 120 Not assessed 








Note: 

The fire performance of the system will be dependent on the diameter and wall thickness of the pipe and installed location as detailed in 

the tables above. The shell of the pipe wrap assembly shall be sealed in the element of construction by a bead of DST Group 

intumescent mastic/sealant with a minimum fire rating of 2 hours. Reference should be made to manufacturers’ literature and BRE Global 

assessment report CC241402 for further information 

Hilti Aktiengesellschaft 

Feldkircher Strasse 100, Postfach 333, FL-9494 Schaan, Liechtenstein 

Tel: +423 234 3004 • Fax: +423 234 2674 

E-mail: fs-ej-team@hilti.com • Website: www.hilti.com 

UK Sales: Hilti (G.B.) Limited 

1 Trafford Wharf Road, Trafford Park, Manchester M17 1BY, United Kingdom 

Tel: +44 (0)161 886 1000 • Fax: +44 (0)161 786 3890 

Certificate No: 090a(3) to LPS 1132: Issue 4 

86 20 Nov 2011

CP 611A - LPCB Ref. No.: 090a(3) 

Product 

Name 

CP 

611A 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 



Configuration: 

fire side 


middle 


non-fire side 

Use 

Cables 

Use 

Trays 

Use 

Pipes 

Fire 

Resistance 

(min) 

Integrity / 

Insulation 

Wall 100+ Drywall 25mm CP611A No filling 30mm CP611A Yes No No 120 / 60 090a/01 

Wall / Floor 110+ L W 

Concrete 


Concrete 


Concrete 


Concrete 


Concrete 


Concrete 

Wall / Floor 150+ Reinforced 

vermiculite 

concrete 

Wall 100+ L W 

Concrete 

Wall 100+ L W 

Concrete 

Floor 120+ Reinforced 

autoclaved 

aerated 

concrete 

slabs 

minimum 

density 

670kg/m³ 

Floor 120+ Reinforced 

autoclaved 

aerated 

concrete 

slabs 

minimum 

density 

670kg/m³ 

50mm CP611A N/A 60mm 

rockwool 

Yes Yes No 30 / 30 

50mm CP611A 50mm 50mm CP611A Yes Yes No 90 / 60 

rockwool 

10mm CP611A 130mm 10mm CP611A Yes No No 240 / 90 

rockwool 


rockwool 


rockwool 

110mm 

N/A 40mm CP611A Yes Yes No 120 / 90 

rockwool 

40mm CP611A N/A 110mm Yes Yes No 120 / 90 

rockwool 

60mm CP611A N/A N/A No No PVC 

pipe 

40mm 

Ø 

x3mm 

thick 

N/A N/A 60mm CP 

611A 

No No PVC 

pipe 

40mm 

Ø 

x3mm 

thick 

80mm CP611A N/A N/A No No PVC 

pipe 

40mm 

Ø 

x3mm 

thick 

N/A N/A 80mm CP611A No No PVC 

pipe 

40mm 

Ø 

x3mm 

thick 

240 / 240 

240 / 240 

180 / 120 

180 / 180 

Cert. 

No. 

Note: 

Please refer to installation instructions for further details. 


CP 636 - LPCB Ref. No.: 090a(2) 

Product 

Name 

Element of 

construction 

orientation 

Element of 

construction 

thickness/material 

CP 636 Floor 150mm+ Aerated 

Concrete 

Floor 150mm+ Aerated 

Concrete 


fire side 


non-fire side 

Use: 

cables 

Use: 

trays 

Use: 

conduit 

pipes 

Aperture 

Size 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

N/A 150mm CP636 Yes Yes Yes 1000x600 180 90 532a/01 

50mm mineral 

fibre 

(140kg/m 3 ) 

75mm CP636 Yes Yes No 600x600 240 90 

Wall 150mm+ Masonry N/A 150mm CP636 Yes Yes Yes 2000x1200 20 120 

Wall 120mm+ Masonry N/A 100mm CP636 Yes Yes No 600x600 240* 60* 

Wall 200mm+ Masonry N/A 185mm CP636 Yes Yes Yes 1200x600 240 60 

Cert. 

No. 

Note: 

* To achieve this fire resistance the penetrations should be coated with a 30mm wide x 0.5mm thick layer of Hilti CP611A where they 

pass through the wall. The coated section should be positioned centrally within the wall thickness. 


20 Nov 2011 87



CP 601S - LPCB Ref. No.: 090a(1) 

Product 

Name 

CP 

601S 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 


fire side 


middle 

Floor 150+ L W Concrete 20mm CP601S 110mm mineral 

fibre 

(100kg/m 3 ) 


fibre 

(100kg/m 3 ) 


fibre 

(100kg/m 3 ) 

Wall 100+ L W Concrete 20mm CP601S 60mm mineral 

fibre 

(100kg/m 3 ) 


fibre 

(100kg/m 3 ) 


fibre 

(100kg/m 3 ) 


non-fire 

side 

20mm 

CP601S 

20mm 

CP601S 

20mm 

CP601S 

20mm 

CP601S 

20mm 

CP601S 

20mm 

CP601S 

Use 

Copper 

pipes 

42- 

200mm 

dia. 

1.25- 

10.0mm 

wall 

Copper 

pipes 

42- 

200mm 

dia. 

1.25- 

10.0mm 

wall 

Copper 

pipes 

42- 

50mm 

dia. 

1.25- 

10.0mm 

wall 

Copper 

pipes 

42- 

200mm 

dia. 

1.25- 

10.0mm 

wall 

Copper 

pipes 

42- 

200mm 

dia. 

1.25- 

10.0mm 

wall 

Copper 

pipes 

42- 

50mm 

dia. 

1.25- 

10.0mm 

wall 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cert. 

No. 

120 0 520a/01 

240 0 

240 0 

120 0 

240 0 

240 0 

Note: 

1. Product used as a pipe penetration sealant. 


CP 601S - LPCB Ref. No.: 090a(1) 

Product 

Name 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

Dept of 

CP620 

(mm) 

(notes 

2 & 5) 

Fire 

Side 

Penetration 

Size 

(notes 1, 3, 

4) 

CP 601S Floor 150+ L W concrete 15 N/A 144mm mineral 

fibre (100kg/m 3 ) 

Floor 150+ L W concrete 30 N/A 135mm mineral 


Floor 150+ L W concrete 100 N/A 135mm mineral 


Wall 100+ L W concrete 30 15mm 70mm mineral 

CP601S fibre (100kg/m 3 ) 

Wall 100+ L W concrete 12 10mm 12mm dia PE 

CP601S 

rod 

Floor 150+ L W Concrete 50mm 20mm 50mm dia. PE 

CP601S 

rod 

Floor 150+ L W Concrete 10mm 6mm 15mm dia. PE 

CP601S 

rod 

Floor 150+ L W Concrete 30mm N/A 35mm dia. PE 

rod 

Floor 150+ L W Concrete 10mm N/A 15mm dia. PE 

rod 

Wall 150+ L W Concrete 50mm 20mm 50mm dia. PE 

CP601S 

rod 

Wall 150+ L W Concrete 10mm 6mm 15mm dia. PE 

CP601S 

rod 

Wall 150+ L W Concrete 30mm N/A 35mm dia. PE 

rod 

Wall 150+ L W Concrete 10mm N/A 15mm dia. PE 

rod 

Non-Fire 

Side 

6mm 

CP601S 

15mm 

CP601S 

15mm 

CP601S 

15mm 

CP601S 

10mm 

CP601S 

20mm 

CP601S 

6mm 

CP601S 

15mm 

CP601S 

6mm 

CP601S 

20mm 

CP601S 

6mm 

CP601S 

15mm 

CP601S 

6mm 

CP601S 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cert. 

No. 

240 240 520a/01 

240 240 

240 240 

120 120 

120 120 

240 240 

240 240 

240 120 

240 240 

240 240 

240 240 

240 90 

240 240 

88 20 Nov 2011



Note: 

1. Product used as a linear gap seal 


CP 620 Expanding Firestop Foam - LPCB Ref No.: 090a(5) 

Product 

Name 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

CP 620 Wall 100 concrete, 

masonry or 

drywall 

Wall 100 concrete, 

masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

drywall 


masonry or 

Depth 

of 

CP620 

(mm) 

(notes 

2 & 5) 

Penetration 

Type 

(notes 

1, 3, 4) 

Penetration 

Size 

Integrity Insulation Cert. 

No. 

145 copper pipe 76mm dia 120 0 090a/03 

200 copper pipe 

+ insulation 

76mm dia + 

insulation 

thickness 

120 120 

145 steel pipe 76mm dia 120 30 

145 steel pipe + 

insulation 

114mm dia 

+ insulation 

thickness 

120 120 

145 PVC pipe 110mm dia 120 120 

200 PE pipe 50mm dia 120 120 

200 PE pipe 110mm dia 120 120 

200 ABS pipe 110mm dia 120 120 

200 single cable 

or cable 

bundle 

145 cable 

bundle 

drywall 

Wall 120 drywall 120 copper pipe 

+ insulation 

Wall 120 drywall 120 cable 

trunking 

(Note 6) 

70mm dia 120 120 

100mm dia 120 60 

145 cable tray 150 x 25mm 120 120 

200 cable tray 250 x 25mm 120 120 

77mm dia + 

insulation 

thickness 

100 x 

100mm 

120 60 

120 60 

Wall 120 drywall 120 PVC pipe 100mm dia 120 60 

Wall 120 drywall 120 cable tray 150 x 25mm 

150 x 25mm 

150 x 25mm 

120 60 

Floor 150 LW Concrete 200 cable tray 320 x 60mm 150 60 

Floor 150 LW Concrete 150 copper pipe 89mm dia + 150 120 

+ insulation insulation 

thickness 

Floor 150 LW Concrete 200 PVC pipe 50mm dia 150 90 


Floor 150 LW Concrete 200 steel pipe + 114mm dia 150 90 

insulation + insulation 

thickness 

Floor 150 LW Concrete 150 cable tray 320 x 60mm 120 30 



20 Nov 2011 89



Product 

Name 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

Depth 

of 

CP620 

(mm) 

(notes 

2 & 5) 

Penetration 

Type 

(notes 

1, 3, 4) 

Floor 150 LW Concrete 150 steel pipe + 

insulation 

Penetration 

Size 

114mm dia 

+ insulation 

thickness 

Integrity Insulation Cert. 

No. 

120 60 

Notes: 

1. The penetrating services should be installed with a minimum separation of 100mm from any other penetrating service and a minimum 

distance of 50mm from the edge of the seal. 

2. An additional bead of 25x25mm of CP620 should be applied around each service (except plastic pipes where it penetrates each face 

of the seal. 

3. Plastic pipes (PE, PVC or ABS) must be fitted with Hilti CP643 pipe collars. 

4. Please refer to manufacturer’s installation instructions for more details. 

5. For seals thicker than the supporting wall, a framework should be installed using type 5 plasterboard. Refer to manufacturer’s 

instructions for further details. 

6. Cable trunking tested with 30% fill of 12mm diameter cables and packed with CP651 cushions above cables at the location where the 

service passed through the partition. 


CF 125-50 Penetration Seals - LPCB Ref No.: 090a(6) 

Product 


Name 

fire side 

CF 125- 

50 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Wall 150 Nominal 

1mm 

coating of 

CP671 


middle 

150mm 

CF 125-50 


non-fire 

side 

Nominal 

1mm 

coating 

of CP671 

Use 

300 x 

300mm 

aperture in 

LW 

blockwork 

containing: 

225 x 

26mm 

steel cable 

types 5- 

25mm dia. 

50mm 

galvanised 

steel 

pipe with 

4.2mm 

wall 

thickness 

Integrity 

(minutes) 

Insulation 

(minutes) 

Cert. 

No. 

30 30 090a/04 


CF 125-50 Linear Gap Seals - LPCB Ref No.: 090a(6) 

Product 


Name 

fire side 

CF 125- 

50 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 

Wall 100 900 x 15mm 

CF125-50 

Wall 100 900 x 15mm 

CF125-50 


middle 


non-fire 

side 

Use 

N/A N/A seal 

between 

softwood 

and LW 

blockwork 

N/A N/A seal 

between 

softwood 

and 

common 

brickwork 

Integrity 

(minutes) 

Insulation 

(minutes) 

Cert. 

No. 

120 120 090a/04 

150 120 

90 20 Nov 2011



Product 

Name 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 


fire side 

Wall 150 Nominal 

1mm 

coating of 

CP671 

Wall 200 950x 135 x 20 

mm CF125-50 


middle 

900 x 50mm 

CF125-50 

N/A 


non-fire 

side 

Nominal 

1mm 

coating 

of CP671 

15mm 

CP606 

mastic 

Use 

seal 

between 

mortar 

lintel 

and steel 

deck 

seal 

between 

concrete 

faces 

Wall 100 950 x 15mm N/A N/A seal 

between 

concrete 

faces 

Wall 100 Up to 25mm 

dia. Holes 

Floor 150 950 x 135 x 20 

mm CF125- 

50 

N/A N/a seal 

between 

concrete 

faces 

N/A 

15mm 

CP606 

mastic 

seal 

between 

concrete 

faces 

Integrity 

(minutes) 

Insulation 

(minutes) 

150 120 

240 120 

120 120 

120 120 

240 180 

Cert. 

No. 

Certificate No: 090a(8) to LPS1132: Issue 4 

CP 606 Intumescent Mastic - Penetration Seals - LPCB Ref No.: 090a(8) 

Product 

Name 

Element of 

construction 

orientation 


gap size 

(mm) 


fire side 


middle 


non-fire side 

CP 606 

100mm AC 

wall 

150mm AC 

floor 

100mm AC 

wall with 

cylindrical 

steel sleeve 

N/A 20mm CP606 60mm 

Rockfibre 

100kg/m 3 

N/A 

Max 

30mm 

80mm 

Rockfibre/m 3 

100kg/m 3 

density 

70mm 

Rockfibre 

140kg/m 3 

density 

density 

20mm CP606 

Use 

42mm 

copper 

pipe 

with 

1.25mm 

wall 

thickness 

N/A 20mm CP606 42mm 

copper 

pipe 

with 

1.25mm 

wall 

thickness 

N/A 15mm CP606 Up to 

600mm 

steel 

pipe 

with 

minimum 

3mm 

wall 

thickness 

Integrity 

(min) 

Insulation 

(min) 

Cert. 

No. 

240 0 090a/07 

240 0 

240 0 


CP 606 Intumescent Mastic - Linear Gap Seals - LPCB Ref No.: 090a(8) 

Product 

Name 

Element of 

construction 

orientation 

Gap Size 

(mm) 


fire side 


middle 


non-fire side 

CP 606 

150mm 

AC/AC floor 

Up to 

15 

30mm PE 

foam rod 

Use 

Integrity 

(min) 

Insulation 

(min) 

Cert. 

No. 

N/A 60mm CP606 120 60 090a/07 

20 Nov 2011 91



Product 

Name 

Element of 

construction 

orientation 

150mm 

AC/AC floor 

150mm 

AC/AC floor 

150mm 

AC/AC floor 

Vertical 

linear gap 

between 

150mm AC 

blockwork 

wall minimum 

density 

760kg/m³ 

/Galvanised 

Mild steel 

angle 

150mm x 

20mm x 

2mm thick 

Vertical 

linear gap 

between 

150mm AC 

blockwork 

wall minimum 

density 

760kg/m³ / 

Galvanised 

mild steel 

angle 

150mm x 

20mm x 2mm 

thick 

Horizontal 

linear gap 

between 

150mm AC 

blockwork 

wall minimum 

density 

760kg/m³ / 

Galvanised 

mild steel 

angle 

150mm x 

20mm x 2mm 

thick 

150mm 

AC/AC floor 

150mm 

AC/AC floor 

Gap Size 

(mm) 

15 to 

30 


fire side 

30mm PE 

foam rod 

Up to 135mm of 

15 CF125-50 

15 to 30 135mm of 

CF125-50 

30mm 

10mm CP606 

& 25mm Ø PE 

backing rod 


middle 


non-fire side 

Use 

Integrity 

(min) 

Insulation 

(min) 

N/A 

10mm of 

CP606 for 

gaps of 

15mm. 

15mm of 

CP606 for 

gaps of 20 to 

30mm. 

240 120 

N/A 6mm CP606 120 60 

N/A 

N/A 

30mm 10mm CP606 130mm 

Mineral wool 

96kg/m² 

50mm 

Up to 15 

20 to 

30 

10mm CP606 

& 2 x 25mm Ø 

PE backing rod 

70mm of 

Rockfibre 

140kg/m 3 

density 

70mm of 

Rockfibre 

140kg/m 3 

density 

10mm of 

CP606 for 

gaps of 

15mm. 

15mm of 

CP606 for 

gaps of 20 to 

30mm. 

10mm CP606 

& 25mm Ø PE 

backing rod 

240 120 

240 90 

10mm CP606 240 90 

N/A N/A 30 0 

N/A 

N/A 

10mm 

CP606 

15mm 

CP606 

240 240 

240 210 

Cert. 

No. 

92 20 Nov 2011



Product 

Name 

Element of 

construction 

orientation 

75mm 

steel/steel or 

AC/steel floor 

75mm 

steel/steel or 

AC/steel floor 

150mm 

AC/AC floor 

100mm 

plasterboard 

partition wall 

head to 

corrugated 

metal 

decking 

100mm 

plasterboard 


head to 

corrugated 

metal 

decking 

100mm 

plasterboard 


head to 

AC block 

100mm 

plasterboard 


head to 

AC block 

65mm AC 

wall with 

cement 

board facings 

and 

galvanised 

steel 

top channel 

Steel framed 

doorset in 

steel or AC 

supporting 

wall 

Timber 

framed 

doorset 

in timber or 

concrete 

supporting 

wall 

Timber 

framed 

doorset 

in timber or 

concrete 

supporting 

wall 

Gap Size 

(mm) 


fire side 

Up to 15 70mm of 

Rockfibre 

140kg/m 3 

density 

20 to 30 70mm of 

Rockfibre 

140kg/m 3 

density 

6 to 15 144mm of 

Rockfibre 

100kg/m3 

density 

Dependant 10mm CP606 

on decking 

profile 

Dependant 

on decking 

profile 

5mm CP606 

10 10mm CP606 

& 15mm of 

Rockfibre 

100kg/m 3 

density 

5 5mm CP606 

& 20mm of 

Rockfibre 

100kg/m 3 

density 


middle 

N/A 

N/A 

N/A 

80mm of 

Rockfibre 

100kg/m 3 

density 

90mm of 

Rockfibre 

100kg/m 3 

density 

N/A 

N/A 


non-fire side 

10mm 

CP606 

15mm 

CP606 

6mm 

CP606 

10mm 

CP606 

5mm 

CP606 

10mm 

CP606 & 

15mm of 

Rockfibre 

100kg/m 3 

density 

5mm CP606 

& 20mm of 

Rockfibre 

100kg/m 3 

density 

Use 

Integrity 

(min) 

Insulation 

(min) 

240 0 

240 30 

240 240 

120 120 

120 120 

120 120 

120 120 

6 to 15 6mm CP606 N/A N/A 120 120 

30 Minimum 

70mm 

Rockfibre 

140kg/m 3 

density 

N/A 

Up to 6 6mm CP606 Minimum 

78mm 

Rockfibre 

140kg/m 3 

density 

6 to 30 15mm CP606 Minimum 

65mm 

Rockfibre 

140kg/m 3 

density 

15mm 

CP606 

6mm 

CP606 

15mm 

CP606 

240 0 

120 0 

120 0 

Cert. 

No. 

20 Nov 2011 93



Product 

Name 

Element of 

construction 

orientation 

Hardwood 

timber 

framed 

doorset with 

or without 

Architraves 

in concrete 

or masonry 

wall 

construction 

670kg/m³ 

minimum 

density (1) 

Hardwood 

timber 

framed 

doorset with 

or without 

Architraves 

in concrete 

or masonry 

wall 

construction 

670kg/m³ 

minimum 

density (1) 

Hardwood 

timber 

framed 

doorset with 

or without 

Architraves 

in concrete 

or masonry 

wall 

construction 

670kg/m³ 

minimum 

density (1) 

Hardwood 

timber 

framed 

doorset with 

or without 

Architraves 

in concrete 

or masonry 

wall 

construction 

670kg/m³ 

minimum 

density (1) 

Gap Size 

(mm) 

Up to 

10mm 

10 to 

18mm 

18 to 

30mm 

Up to 

30mm 


fire side 

5mm CP606 & 

(optional) Ø 

PE backing rod 

5mm CP606 & 

Ø PE backing 

rod 

10mm CP606 

& Ø PE 

backing rod 

10mm CP606 


middle 

N/A 

N/A 

N/A 

Minimum 

180mm tightly 

packed stone 

mineral fibre 


non-fire side 

5mm CP606 & 

(optional) Ø PE 

backing rod 

5mm CP606 & 

Ø PE backing 

rod 

10mm CP606 

& Ø PE 

backing rod 

Use 

Integrity 

(min) 

Insulation 

(min) 

120 0 

90 0 

90 0 

10mm CP606 120 0 

Cert. 

No. 

Notes: 

1. For FD30 Doorsets the following frame materials are applicable Softwood, Hardwood & Mineral composite having minimum density’s 

of 450kg/m² or MDF having a minimum density of 750kg/m³. For FD60 & FD90 Doorsets the following frame materials are applicable 

Hardwood & Mineral composite having a density of 620kg/m³. 

2. AC - Aerated Concrete. 

3. Please refer to Hilti installation instructions for further detail 


94 20 Nov 2011

CP 657 Blocks With CP611A Sealant - LBCB Ref. No. 090a(9) 

Product 

Use 

Name 

CP 657 

blocks with 

CP611A 

sealant 

Element of 

construction 

orientation 

Element of 

construction 

thickness 

(mm) 



Element of 

construction 

material 

Wall 200 Concrete or 

masonry 


masonry 


masonry 


masonry 


masonry 


masonry 


masonry 


masonry 


masonry 


masonry 

60.3 mm diameter x 

2.9 mm wall thickness 

steel pipe penetration 

Floor 200 Concrete 50 mm diameter x 3 

mm wall thickness PVC 

pipe 

Floor 200 Concrete 60.3 mm diameter x 


steel pipe penetration 

Floor 200 Concrete 50 mm diameter x 5 

mm wall thickness 

polyethylene pipe 

Floor 200 Concrete 110 mm wide cable 

tray supporting 3 off 

3x50 mm 2 PVC/copper 

cables 

Fire 

Resistance 

Integrity 

(min) 

(E) 

Fire 

Resistance 

Insulation 

(min) 

(I) 

Cert. 

No. 

180 120 090a/08 

22 mm diameter 

copper pipe 

180 120 

28.9 mm diameter x 180 180 

2.6mm wall thickness 

stainless steel pipe 

168.3 mm diameter x 180 90 


steel pipe with 

Autopack 25 mm thick 

Rockwool and PVC 

applied insulation 

50 mm diameter x 3 180 180 

mm wall thickness PVC 

pipe 

50 mm diameter x 5 180 180 

mm wall thickness 

polyethylene pipe 

316 mm wide cable 180 180 



cables 




cables 

Cable bundle 40 180 180 

cables 2x1.5mm 2 


20x2x0.6mm 2 


bundles of 10 cables 

180 180 

180 120 

180 180 

180 120 

180 180 

Floor 200 Concrete 316 mm wide cable 

mm 2 


PVC/copper cables, 15 

3x4 mm 2 , 15 4x2.5 

Note: 

For CP657 Blocks with CP611A sealant: 

The CP 657 blocks shall be compress fitted into the aperture with blocks cut, where required, to fit around the services and aperture. CP 

611A sealant shall be applied on blocks in direct contact with the aperture and for the full depth of the aperture (200mm) around each 

penetration element of a thickness nominally 5mm (15mm around pipes). Cable bundles shall be completely filled with CP 611A sealant. 

See manufacturer's installation/application instruction for full details. 


20 Nov 2011 95



CP 672/CFS-SP WB Linear Gap Seals - LPCB Ref No: 090a(7) 

Product 

Name 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

Rockwool 

RP-V 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

Rockwool 

Termarock 40 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

Rockwool 

RP-V 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

Rockwool 

Termarock 40 

Element of 

construction 

Orientation 

Vertical joint 

in Wall 

Vertical joint 

in Wall 

Element of 

construction 

Thickness/ 

Depth 

(mm) 

150 

(minimum) 

150 

(minimum) 

Floor 150 

(minimum) 

Floor 150 

(minimum) 

Element of 

construction 

Material 

Aerated 

Concrete, 

blockwork or 

masonry. 

Minimum 

density 

380kg/m³ 

Aerated 

Concrete, or 

masonry. 

Minimum 

density 

380kg/m³ 

Concrete and 

blockwork. 

Minimum 

density 

2400kg/m³ 

Concrete and 

blockwork. 

Minimum 

density 

2400kgm³ 

Application 

Maximum joint width 100 mm, 

minimum installation depth 150mm. 

Joint 50% compression filled with 

50mm thick layers of Rockwool RP- 

V mineral fibre panels of nominal 

38.5kg/m3 density compress fitted 

trimmed flush with both the inner 

and outer surface of the joint. Both 

surfaces spray coated with CP 

672/CFS-SP WB nominally 3-5mm 

thick extending beyond the edge of 

the joint onto surface of 

surrounding construction by a 

minimum of 15mm each side. 25% 

lateral expansion applied during 

test. 




50mm thick layers of Rockwool 

Termarock 40 mineral fibre panels 

of nominal 42.6kg/m 3 density 

compress fitted trimmed flush with 

both the inner and outer surface of 

the joint. Both surfaces spray 

coated with CP 672/CFS-SP WB 

nominally 3-5mm thick extending 

beyond the edge of the joint onto 

surface of surrounding construction 

by a minimum of 15mm each side. 

0-40% lateral expansion applied 

during tests. 




50mm thick layers of Rockwool RP- 

V mineral fibre panels of nominal 

38.5kg/m 3 density compress fitted 

trimmed flush with the upper (nonfire) 

surface of the joint. The upper 

surface spray coated with CP 

672/CFS-SP WB nominally 3-5mm 

thick extending beyond the edge of 



minimum of 15mm each side. 0- 

25% lateral expansion applied 

during test. 




50mm thick layers of Rockwool 

Termarock 40 mineral fibre panels 

of nominal 42.6kg/m 3 density 

compress fitted trimmed flush with 

the upper (non-fire) surface of the 

joint. The upper surface spray 

coated with CP 672/CFS-SP WB 

nominally 3-5mm thick extending 

beyond the edge of the joint onto 

surface of surrounding construction 

by a minimum of 15mm each side. 

40% lateral expansion applied 

during test. 

Fire 

Resistance 

(min) 

Integrity/ 

Insulation 

(EN 1366- 

4) 

Cert. 

No. 

240/240 090a/05 

240/240 

240/120 

240/120 

96 20 Nov 2011




CP 672/CFS-SP WB Linear Gap Seals - LPCB Ref No: 090a(7) 

Product 

Name 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

64kg/m³ 

density 

mineral fibre 

batt 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

32kg/m³ 

density 

mineral fibre 

batt 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with CP 

777 plugs 

and CP 757 

strips 

Element of 

construction 

Orientation 

Element of 

construction 

Thickness 

/Depth 

(mm) 

Element of 

construction 

Material 

Floor 115 Lightweight 

concrete floor 

slab 



slab 

Wall head to 

concrete topped 

metal deck 

assembly 

Wall thickness 

100 Floor 

assembly 140 

Note 1 

Application 

Maximum joint width 75mm, 

minimum installation depth 

115mm. Joint filled with 4 

layers of 108mm wide x 38mm 

thick layers of mineral fibre batt 

of nominal 64kg/m 3 density 

50% compress fitted flush with 

the lower (fire side) surface of 

the joint. The upper surface 

spray coated with CP 

672/CFS-SP WB nominally 

6mm thick flush with the upper 

(non-fire) surface and 

extending beyond the edge of 



minimum of 20mm each side 

Maximum joint width 90mm, 

minimum installation depth 

115mm. Joint filled with 4 

layers of 112mm wide x 38mm 

thick layers of mineral fibre batt 

of nominal 32kg/m 3 density 

42% compress fitted flush with 

the lower (fire side) surface of 

the joint. The upper surface 

spray coated with CP 

672/CFS-SP WB nominally 

3mm thick flush with the upper 

(non-fire) surface and 

extending beyond the edge of 



minimum of 12mm each side 

Minimum 25mm gap between 

wall head and metal deck 

increasing to 100 mm into deck 

profile. CP 777 plugs friction 

fitted to completely fill deck 

profile cavities flush with both 

sides of 

wall. CP 767 strips 

compressed 50% and inserted 

into remaining joint gaps flush 

with both sides of wall. 

Complete outer surface of joint 

coated with CP 672/CFS-SP 

WB nominally 3 mm thick 

extending beyond the 

perimeter of the seal onto 

surface of surrounding gypsum 

wall and decking by 13mm on 

both sides of wall assembly. 

Fire 

Resistance 

(mm) 

Integrity/ 

Insulation 

(BS 476: 

Part 20) 

Cert. 

No. 

240/120 090a/05 

180/120 

120/120 

20 Nov 2011 97



Product 

Name 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 64 

kg/m³ mineral 

wool 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

40kg/m³ 

Mineral wool 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 64 


wool 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

64kg/m³ 

mineral wool 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 32 


wool 

Element of 

construction 

Orientation 

Wall head to 

concrete topped 

metal deck 

assembly 

Floor / Curtain wall 

system 

Partition wall head 

to floor soffit 

Concrete/Masonry 

wall head to floor 

soffit 


to composite floor 

Element of 

construction 

Thickness 

/Depth 

(mm) 

Wall thickness 

200 Floor 

assembly 140 

Floor 

thickness 200 

Element of 

construction 

Material 

Note 2 

Floor 

Reinforced 

Concrete. 

Mminimum 

density 

2200kg/m³ 

Application 

Minimum 90 mm gap between 

wall head and metal deck 

increasing to 165 mm into deck 

profile. Mineral wool of 64 

kg/m 3 density 50% compress 

packed into flutes/joint flush 

with both sides of wall. 

Complete outer surface of joint 

coated with CP 672/CFS-SP 

WB nominally 3 mm thick 

extending beyond the 

perimeter of the seal onto 

surface of surrounding gypsum 

wall and decking by 

13mm on both sides of wall 

assembly. 

Maximum gap between 

supporting floor and the façade 

(Curtain wall system) 210mm. 

The Horizontal Linear gap seal 

(perimeter seal) system 

comprised of 7 layers of 

mineral wool board (RPV -40 

Rockwool) 200mm wide 60mm 

thick compressed to 50% and 

with a density of 40kg/m³. 

Mineral wool coated on the 

upper surface (non-fire side) 

with dry film thickness of 1.5- 

2.0mm of CP 672/CFS-SP WB 

fire stop joint spray. 

Note 3 Note 3 Minimum 25mm gap between 

wall head and floor soffit. Joint 

seal comprising of Mineral wool 

64 kg/m³ with 50% 

compression filled to the full 

depth of the wall and coated 

with CP 672/CFS-SP WB Fire 

stop joint spray 

Note 4 Note 4 Minimum 25mm gap between 

wall head and floor soffit. Joint 


64 kg/m³ with 50% 

compression filled to the full 

depth of the wall and coated 

with CP 672/CFS-SP WB Fire 

stop joint spray. 

Note 5 Note 5 Maximum 50mm gap between 

the top of the wall partition 

boards and the valleys of the 

steel floor construction. Joint 


32 kg/m³ with 50% 

compression fitted between the 

wall board edges and the 

underside of the steel floor 

construction either side of the 

wall coated with a 3mm wet 

thickness coating of CP 

672/CFS-SP WB Fire stop joint 

spray overlapping the spray 

applied steel protection 

material by 50mm and by 

12mm over the wall boards. 

Fire 

Resistance 

(mm) 

Integrity/ 

Insulation 

(BS 476: 

Part 20) 

120/120 

120/120 

240/240 

240/240 

120/120 

Cert. 

No. 

98 20 Nov 2011



Product 

Name 

CP 

672Y/CFS- 

SP WB Fire 

stop joint 

spray with 32 


wool 

CP 672/CFS- 

SP WB Fire 

stop joint 

spray with 

32kg/m³ 

mineral wool 

Element of 

construction 

Orientation 





Element of 

construction 

Thickness 

/Depth 

(mm) 

Element of 

construction 

Material 

Application 

Note 6 Note 6 Maximum 100mm aperture 

around the lattice beam. Joint 


32 kg/m³ with 50% 

compression fitted into the 

aperture around the lattice 

beam and coated with a 3mm 

wet thickness coating of CP 

672/CFS-SP WB Fire stop joint 

spray to all exposed mineral 

wool overlapping the spray 

applied steel protection 

material by 50mm and by 

12mm over the wall boards. 

Note 7 Note 7 Maximum 25mm gap between 

the top of the wall partition 

boards and the valleys of the 

steel floor construction. Joint 

seal comprising of layers of 

Mineral wool 32 kg/m³ cut to 

the shape of the fluted floor 

units approximately 20% larger 

than the widths of the flutes 

and compression fitted into the 

flutes of the floor units above 

the ceiling channel, additional 

50mm x 30mm sections of 

mineral wool shall be 50% 

compression fitted between the 

top of the wall boards and the 

underside of the steel floor 

units either side of the wall and 

coated with a 3mm wet 

thickness coating of 

CP 672Y/CFS-SP WB Fire 

stop joint spray to exposed 

mineral wool and overlapping 

the wall boards by 12mm. 

Fire 

Resistance 

(mm) 

Integrity/ 

Insulation 

(BS 476: 

Part 20) 

120/120 

120/120 

Cert. 

No. 

Notes: 

1 2 hour fire rated Wall 64 mm steel stud faced on each side with 2 x 15 mm layers Type ‘X’ gypsum board and Profiled metal deck 

assembly topped with 64 mm concrete. 

2. Concrete block wall and Profiled metal deck assembly topped with 64 mm concrete. 

3. Applicable to UL Joint system No’s. HW-D-0292 & HW-D-0295. The specification of the gypsum board based drywall and composite 

steel/concrete profiled deck supporting constructions shall provide the required fire resistance of 240 minutes. 

4. Applicable to UL Joint system No’s HW-D-0294 & HW-D-0296. The specification of the concrete/masonry wall and composite 


5. Applicable to UL Joint system No’s. HW-D-0190. The specification of the gypsum board based drywall and composite steel/concrete 

profiled deck supporting constructions shall provide the required fire resistance of 120 minutes. 

6. Applicable to UL Joint system No’s. HW-D-0218. The specification of the gypsum board based drywall and composite steel/concrete 

profiled deck supporting constructions shall provide the required fire resistance of 120 minutes. 

7. Applicable to UL Joint system No’s. HW-D-0042 & HW-D-0049. The specification of the gypsum board based drywall and composite 


Certificate No: 090a(10) to LPS1132: Isuue 4 

20 Nov 2011 99



CP 660 Wall System - LPCB Ref No.: 090a(10) 

Product 

Name 

CP 660 

Element of 

construction 

orientation 

Wall 

(system H) 

Wall 

(system A) 

Wall 

(system B) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

Penetration 

Type 

Penetration 

Type 

120 Drywall Blank seal 

without service 

penetrations 

120 Drywall Perforated 

300mm wide 

1.5mm thick 

mild steel 

cable tray (1) 

with 1x50mm 

dia. Copper 

core electric 

Cable, 

1x32mm dia. 

Copper core 

Electric Cable, 

3x16mm dia. 

Mild steel 

pipes with 

1.5mm wall 

thickness and 

3x16mm dia. 

Plastic pipes 

with 1.0mm 

wall thickness 

and Perforated 

300mm wide 

1.5mm thick 

mild steel 


with 2x50mm 

dia. Aluminium 

core Electric 

Cables and 

1x70mm dia. 

Copper core 

Electric cable. 

120 Drywall Perforated 

300mm wide 

1.5mm thick 

mild steel 


with 15x13mm 

dia. Copper 

core Electric 

Cables in 2 

layers and 

30x12mm 

communication 

cables in 

bundle. and 

Perforated 

300mm wide 

1.5mm thick 

mild steel 


with 15x12mm 

dia. Copper 

core Electric 

Cables in 2 

layers 

Penetration/seal 

Size 

(mm) 

400 x 400 x 120 

thick 

400 x 400 x 120 

thick 

400 x 400 x 120 

thick 

Integrity 

(min) 

Insulation 

(min) 

Cert. 

No. 

120 120 090a/09 

120 60 

120 90 

100 20 Nov 2011



Product 

Name 

Element of 

construction 

orientation 

Wall 

(system C) 

Wall 

(system D) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

Penetration 

Type 

Penetration 

Type 

120 Drywall 1x50mm dia. 

PVC-u pipe 

with 2.4mm 


(2) and 

1x50mm dia. 

PVC-u pipe 

with 1.8mm 


(2) and 

CP643- 

50/1.5N pipe 

collar on each 

side of 

penetration 

seal (4) and 

1x110mm dia. 

PVC-u pipe 

with 1.8mm 


(3) and 

CP643-110/4N 

pipe collars on 

each side of 

the penetration 

seal (4) and 

1x110mm dia. 

PVC-u pipe 

with 12.3mm 


(3) and 

CP643-110/4N 

pipe collars on 

each side of 

the penetration 

seal (4) 


PVC-u pipe 

with 1.8mm 


(2) with 1 layer 

of CP648-E 

pipe wrap (5). 

and 1x110mm 

dia. PVC-u 

pipe with 

1.8mm wall 

thickness (3) 

with 2 layers of 

CP648-E pipe 

wrap (5). and 

1x110mm dia. 

PVC-u pipe 

with 12.3mm 


(3) with 2 

layers of 

CP648-E pipe 

wrap (5). 


Size 

(mm) 

400 x 400 x 120 

thick 

400 x 400 x 120 

thick 

Integrity 

(min) 

Insulation 

(min) 

120 120 

120 120 

Cert. 

No. 

20 Nov 2011 101



Product 

Name 

Element of 

construction 

orientation 

Wall 

(system F) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

Penetration 

Type 

Penetration 

Type 


PE pipe with 

12.5mm wall 

thickness (3) 

and CP643- 

110/4N pipe 

collars on each 

side of the 

penetration 

seal (4) and 

1x110mm dia. 

PE pipe with 

2.4mm wall 

thickness (3) 

and CP643- 

110/4N pipe 


side of the 

penetration 

seal (4) and 

1x50mm dia. 

PE pipe (2) 

with 4.2mm 


and 1x50mm 

dia. PE pipe 

(2) with 2.4mm 


and CP643- 

50/1.5N pipe 


side of the 

penetration 

seal (4) 


Size 

(mm) 

400 x 400 x 120 

thick 

Integrity 

(min) 

Insulation 

(min) 

120 120 

Cert. 

No. 

Notes: 

Wall system 

1. Cable tray fixed to Hilti MQ41/3 unistrut support system, wire cable ties used with cable tray on both sides of the penetration. 

2. Pipe fixed to Hilti MQ41/3 unistrut support system using Hilti MPN-S 1.5” pipe clamps. 

3. Pipe fixed to Hilti MQ41/3 unistrut support system using Hilti MPN-S 110mm pipe clamps. 

5. Pipewrap fixed with ‘Pattex’ self-adhesive tape. 


CP 660 Floor System - LPCB Ref No.: 090a(10) 

Product 

Name 

CP 660 

Element of 

construction 

orientation 

Floor 

(system A) 

Element of 

construction 

thickness 

(mm) 

150 

concrete (6) 

Element of 

construction 

material 

Aerated 

concrete (6) 

Penetration 

Type 

Penetration 

Type 

Blank seal 

without 

service 

penetrations 


Size 

400 x 400 x 150 

thick 

Integrity 

(min) 

Insulation 

(min) 

Cert. 

No. 

120 90 090a/09 

102 20 Nov 2011



Product 

Name 

Element of 

construction 

orientation 

Floor 

(system B) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

150 Aerated 

concrete (6) 

Penetration 

Type 

Penetration 

Type 

Perforated 

300mm wide 

1.5mm thick 

mild steel 


with 1x50mm 

dia. Copper 

core Electric 

Cable, 

1x32mm dia. 

Copper core 

Electric Cable, 

3x16mm dia. 

Mild steel 

pipes with 

1.5mm wall 

thickness and 

3x16mm dia. 

Plastic pipes 

with 1.0mm 

wall thickness. 

and 

Perforated 

300mm wide 

1.5mm thick 

mild steel 


with 2x50mm 

dia. 

Aluminium 

core Electric 

Cables and 

1x70mm dia. 

Copper core 

Electric cable. 


Size 

400 x 400 x 150 

thick 

Integrity 

(min) 

Insulation 

(min) 

180 90 

Cert. 

No. 

20 Nov 2011 103



Product 

Name 

Element of 

construction 

orientation 

Floor 

(system C) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

150 Aerated 

concrete (6) 

Penetration 

Type 

Penetration 

Type 

1x50mm dia. 

PVC-u pipe 

with 4.8mm 


(2) and 

1x50mm dia. 

PVC-u pipe 

with 1.8mm 


(2) and 

CP643- 

50/1.5N pipe 

collar on 

exposed side 

of penetration 

seal (4) and 

1x110mm dia. 

PVC-u pipe 

with 1.8mm 


(3) and 

CP643- 

110/4N pipe 

collars on 

exposed side 

of the 

penetration 

seal (4) and 

1x110mm dia. 

PVC-u pipe 

with 12.3mm 


(3) and 

CP643- 

110/4N pipe 

collars on 

exposed side 

of the 

penetration 

seal (4) 


Size 

400 x 400 x 150 

thick 

Integrity 

(min) 

Insulation 

(min) 

180 180 

Cert. 

No. 

104 20 Nov 2011



Product 

Name 

Element of 

construction 

orientation 

Floor 

(system E) 

Floor 

(system H) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

150 Aerated 

concrete (6) 

150 Aerated 

concrete (6) 

Penetration 

Type 

Penetration 

Type 

1x110mm dia. 

PE pipe with 

12.5mm wall 

thickness (3) 

and CP643- 

110/4N pipe 

collars on 

exposed side 

of the 

penetration 

seal (4) and 

1x110mm dia. 

PE pipe with 

2.4mm wall 

thickness (3) 

and CP643- 

110/4N pipe 

collars on 

exposed side 

of the 

penetration 

seal (4) and 

1x50mm dia. 

PE pipe with 

4.2mm wall 

thickness (2) 

and 1x50mm 

dia. PE pipe 

with 2.4mm 


(2) and 

CP643- 

50/1.5N pipe 

collars on 

exposed side 

of the 

penetration 

seal (4) 

1x50mm dia. 

PVC-u pipe 

with 1.8mm 


(2) with 1 

layer of 

CP648-E pipe 

wrap (5).and 

1x110mm dia. 

PVC-u pipe 

with 1.8mm 


(3) with 2 

layers of 

CP648-E pipe 

wrap (5). and 

1x110mm dia. 

PVC-u pipe 

with 12.3mm 


(3) with 2 

layers of 

CP648-E pipe 

wrap (5). 


Size 

400 x 400 x 150 

thick 

400 x 400 x 150 

thick 

Integrity 

(min) 

Insulation 

(min) 

180 180 

180 180 

Cert. 

No. 

20 Nov 2011 105



Product 

Name 

Element of 

construction 

orientation 

Floor 

(system I) 

Element of 

construction 

thickness 

(mm) 

Element of 

construction 

material 

150 Aerated 

concrete (6) 

Penetration 

Type 

Penetration 

Type 

1x50mm PE 

pipe with 

2.4mm wall 

thickness (2) 

with 1 layer of 

CP648-E pipe 

wrap (5). and 

1x110mm PE 

pipe with 

2.4mm wall 

thickness (3) 

with 2 layers 

of CP648-E 

pipe wrap (5). 

and 1x110mm 

PE pipe with 

12.5mm wall 

thickness (3) 

with 2 layers 

of CP648-E 

pipe wrap.(5) 


Size 

400 x 400 x 150 

thick 

Integrity 

(min) 

Insulation 

(min) 

180 180 

Cert. 

No. 

Notes: 

Floor system 

1. Cable tray fixed to Hilti MQ41/3 unistrut support system, wire cable ties used with cable tray on both sides of the penetration. 

2. Pipe fixed to Hilti MQ41/3 unistrut support system using Hilti MPN-S 1.5” pipe clamps. 

3. Pipe fixed to Hilti MQ41/3 unistrut support system using Hilti MPN-S 110mm pipe clamps. 

4. Fixed to the unexposed face of the penetration seal using M8 threaded rods with hexagonal head steel nuts and washers. 

5. Pipewrap fixed with ‘Pattex’ self-adhesive tape. 

6. Aerated concrete density 670g/m 3 

Certificate No: 090a (11) to LPS 1132: Issue 4 

Penetration Gap Seals – CP670 Fire Safety System (Unframed single layer 50mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type (3) 

CP 670 

Fire 

Safety 

System 

Elements of 

Construction 

Orientation 

Elements of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 

Wall 100 LW Concrete/ 

Masonry/ 

Plasterboard 

partition 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Cables 10mm 

(5)(6) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Cert. 

No. 

90 30 090a/10 

Cables 10mm 90 60 



Product 

Name 

Elements of 

Construction 

Orientation 

Elements of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Aperture 

Size 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Maximum 

aperture 

size 5000 

mm wide 

x 2400 

mm high 

(1). 

Penetration 

Type (3) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Cable Trays 120 60 

Mild Steel 

Trunking 

250mm x 

250mm x 

1.5mm thick 

120 30 

Blank Seals 120 60 

Steel Pipes 

114mm & 

250mm Ø x 

6.3mm thick 

Copper Pipes 

108mm Ø x 

2mm thick 

CP642 Collars 

(recessed/surface 

mounted) pipes 

≤ 160 mm Ø x 

5.6mm thick 

CP643 Collars 

(recessed) 

PVC pipes 

≤ 110 mm Ø x 

4mm thick 

120 0 

120 0 

120 60 

120 0 

Cert. 

No. 

Notes: 

1. LPCB Ref No 090a/10 CP670 Fire Safety System consists of pre-coated CP670 Fire Safety Board (Rocksilk Universal Slab RS 160 - 

180 mineral wool batt maximum 1200m x 600mm wide having a 160-180kg/m3 density utilising cruciform joints at maximum 

dimensions of 2400mm x 1200mm wide), coated with CP 670 Fire Safety Coating nominally 0.7mm thick extending beyond the 

perimeter of the seal onto surface of surrounding construction by 12.5mm unless otherwise stated. 

2. All Gaps around all penetration types are to be sealed with Hilti CP606 (or CP611A where indicated (a)) mastic joint filler. 

3. It is assumed that all penetrating services are effectively independently supported such that their weight does not act on the seal in 

any manner for the stated period 

4. CP642 Collars are approved with Polyethylene (PE), Polyvinyl chloride (PVC), Polypropylene (PP), Polybutylene (PB), and 

Acrylonitrile butadiene styrene (ABS) pipes only. 

5. All cables required to provide 90 to 120 minutes insulation and integrity must include a 150mm coat back of CP670 Fire safety 

coating, where 60 minutes integrity and insulation is required the coat back may be reduced to 100mm and no coat back is required 

where 30 minutes integrity and insulation is required. 

6. Cables may be individual or bunched where they penetrate the CP 670 Fire safety system. 


20 Nov 2011 107



Penetration Gap Seals -CP670 Fire Safety System (Framed double layer 100mm) (4) (8) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Cables ≤ 

20mm Ø 

Cables 20mm 

< Ø ≤ 40mm 

Cables 40mm 

< Ø ≤ 75mm 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Cert. 

No. 

180 200 090a/10 

180 120 

180 120 

Cable Trays 180 120 

Mild Steel 

Trunking 

250mm 

x 250mm x 

1.5mm thick 

120 30 

Blank Seals 240 180 

Steel Pipes ≤ 

250mm Ø x 

6.3mm thick 

Copper Pipes 

≤ 108mm Ø 

x 2mm thick 

CP642 Collars 

(recessed) 

pipes 

≤ 160 mm Ø x 

5.6mm thick 

(5) 

240 30 

240 0 

240 60 

108 20 Nov 2011



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Aperture 

Size 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Maximum 

aperture 

size 

3000 mm 

wide x 

5000 mm 

high 

Penetration 

Type 

CP642 Collars 

(surface 

mounted) 

CP642 Collars 

(independently 

supported ≤ 

250mm Ø) (7) 

CP643 Collars 

(recessed) 

PVC pipes ≤ 

110 mm Ø 

x 4mm thick 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

240 60 

90 60 

120 0 

Cert. 

No. 

Notes: 

1. LPCB Ref No 090a/10 CP670 Fire Safety System consists of pre-coated CP670 Fire Safety Board (Rocksilk Universal Slab RS 160 - 

180 mineral wool batt maximum 1200m x 600mm wide having a 160-180kg/m3 density utilising cruciform joints at maximum 

dimensions of 2400mm x 1200mm wide), coated with CP 670 Fire Safety Coating nominally 0.7mm thick extending beyond the 

perimeter of the seal onto surface of surrounding construction by 12.5mm unless otherwise stated. 

2. All Gaps around all penetration types are to be sealed with Hilti CP606 mastic joint filler. 


any manner for the stated period. 

4. CP670 Fire Safety System (Framed Double Layer system) comprises of an internal steel channel section framework clad on both 

faces with 50mm thick coated CP670 Fire Safety Boards which are retained to the framework via insulation pins and non return 

washers. 


Acrylonitrile butadiene styrene (ABS) pipes only. 

6. 150mm coat back of CP670 Fire Safety Coating required. 

7. CP642 Collars Independently supported is available with Polyethylene (PE) and Polyvinyl chloride (PVC) only. 

8. The framed assembly shall be provided with 25mm of expansion allowance with an additional 20mm restricted expansion which the 

system is proved to be capable of accommodating without any undue effects. 


Penetration Gap Seals – CP670 Fire Safety System (Unframed double layer 100mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high (1). 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Cables 

10mm 

Cables 

10mm 



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Aperture 

Size 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Penetration 

Type 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cables 

20mm 

< 

Ø≤40mm (5)(6) 120 120 

Cables 

40mm 



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

min (mm) 

Element of 

Construction 

Material 


Masonry/ 

Plasterboard 



Masonry/ 

Plasterboard 


Aperture 

Size 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Maximum 

aperture 

size 5000 

mm 

wide x 

2400 mm 

high 

Penetration 

Type 

CP642 

Collars 

(surface 

mounted) 

pipes ≤ 160 

mm Ø 

x 5.6mm 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

thick (4) 120 60 

CP643 

Collars 

(recessed) 

PVC pipes ≤ 

110 mm Ø x 

4mm thick 

120 0 

Cert. 

No. 

Notes: 

1. CP670 Fire Safety System (Unframed Double Layer system) utilises cruciform joints within the CP670 Fire Safety System at 

Maximum dimensions of 2400mm high x 1200mm wide. No single batt is to be of greater dimensions than 1200mm high x 600mm 

coated with CP 670 Fire Safety Coating nominally 0.7mm thick extending beyond the perimeter of the seal onto surface of 

surrounding construction by 12.5mm unless otherwise stated and should have an additional CP670 Fire Safety Coating to batt edges. 

2. All Gaps around all penetration types are to be sealed with Hilti CP606 mastic joint filler. 




Acrylonitrile butadiene styrene (ABS) pipes only 

5. All cables required to provide 90 to 120 minutes insulation and integrity must include a 150mm coat back of CP670 Fire Safety 

Coating, where 60 minutes integrity and insulation is required the coat back may be reduced to 100mm and no coat back is required 

where 30 minutes integrity and insulation is required. 

6. Cables may be individual or bunched where they penetrate the CP 670 Fire Safety System. 


CP657 Blocks with CP651N mastic (wall application) - LPCB Ref. No. 090a(9) 

Product 

Name 

Aperture 

size 

Use 

CP657 

Blocks 

with 

CP615N 

mastic 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Wall 100 Concrete, 

concrete block 

or masonry 

walls minimum 

density 600 

kg/m³ 



or masonry 

walls minimum 

density 600 

kg/m³ 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

Steel Cable 

trays, 

ladders, 

trunking and 

conduit 

supporting all 

cables with 

PVC 

insulation 

Steel, 

Stainless 

steel & cast 

iron Pipes 

max 168mm 

Ø x 14.2mm 

thick 

(100kg/m³ 

mineral fibre 

insulation 

600 x 40mm 

thick) (2) 

Fire 

Resistance 

(min) 

Intergrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cert. 

No. 

120 120 090a/08 

120 120 

20 Nov 2011 111



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 



or masonry 

walls minimum 

density 600 

kg/m³ 



or masonry 

walls minimum 

density 600 

kg/m³ 



or masonry 

walls minimum 

density 600 

kg/m³ 



or masonry 

walls minimum 

density 600 

kg/m³ 

Aperture 

size 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

1000mm 

high x 

700mm 

wide or 

700mm 

high or 

1000mm 

wide 

Use 

Steel, 

Stainless 

steel & cast 

iron Pipes 

max 88.9mm 

Ø x 14mm 

thick (45 - 

100kg/m³ 

Armaflex 

AF/SH 

synthetic 

latex 

insulation 

800 x 9mm 

thick) (2) 

Steel, 

Stainless 

steel & cast 

iron Pipes 

max 88.9mm 

Ø x 14mm 

thick (45 - 

100kg/m³ 

Armaflex 

AF/SH 

synthetic 

latex 

insulation 

800 x 31mm 

thick) (2) 

Copper pipes 

max 88.9mm 

Ø x 3mm 

thick 

(100kg/m³ 

mineral fibre 

insulation 

800 x 40mm 

thick) (2 

Copper pipes 

max 54mm 

Ø x 3mm 

thick (45 - 

100kg/m³ 

Armaflex 

AF/SH 

synthetic 

latex 

insulation 

800 x 9 – 

31mm thick) 

(2) 

Fire 

Resistance 

(min) 

Intergrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

120 90 

120 120 

120 120 

120 90 

Cert. 

No. 

Notes 

For CP657 Blocks with CP651N mastic (wall application); 

1. Hilti CP657 Fire Stop Brick with a minimum thickness of 200mm and a nominal density of 270 ± 30kg/m³. If the minimum thickness of 

the concrete/masonry wall is 200mm, then the seal may be fitted directly into the opening in the wall. If the thickness is less than 

200mm (minimum 100mm for walls) then the opening may either be lined with calcium silicate board, minimum 200mm wide x 25mm 

thick, or the opening increased to at least 200mm by fitting calcium silicate board, minimum 50mm wide x 25mm thick, around the 

opening. The board is fastened with steel screws into metal plugs at max 300mm centres. The boards may be fitted to either face of 

the wall. The calcium silicate board shall be Promatect H or equivalent. 

2. The metal pipes shall be fitted with a mineral wool sleeve that is either continuous through the seal or interrupted and butt up to the 

face of the seal on both faces. 

3. All services passing through the penetration seal system must be supported on both sides of the seal within 500mm from the face of 

the seal so that the weight of the services is not taken by the seal system. 

112 20 Nov 2011




CP657 Blocks with CP651N mastic (floor application) - LPCB Ref. No. 090a(9) 

Product 

Name 

Aperture 

size 

Use 

CP657 

Blocks 

with 

CP615N 

mastic 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Floor 150 Concrete 

minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

Steel Cable 

trays, ladders, 

Trunking and 

conduit 

supporting all 

cables, PVC 

insulated with 

copper 

conductors ≤ 

95mm² 

bunched or un 

bunched & all 

cables with 

aluminium 

conductors 

Steel Cable 

trays, ladders, 

Trunking and 

conduit 

supporting 

cables with 

copper 

conductors ≥ 

95mm² with 

PVC insulation 

Steel, 

Stainless steel 

& cast iron 

Pipes max 

168mm Ø x 

14.2mm thick 

(100kg/m³ 

mineral fibre 

insulation 600 

x 40mm thick) 

(2) 

Steel, 


& cast iron 

Pipes max 

88.9mm Ø x 

14mm thick 

(45 - 100kg/m³ 

Armaflex 

AF/SH 

synthetic latex 


x 9mm thick) 

(2) 

Steel, 


& cast iron 

Pipes max 

88.9mm Ø x 

14mm thick 

(45 - 100kg/m³ 

Armaflex 

AF/SH 



x 31mm thick) 

(2) 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cert. 

No. 

120 120 090a/08 

120 90 

120 120 

120 90 

120 120 

20 Nov 2011 113



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 


minimum 

density 

600kg/m³ 

Aperture 

size 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

700mm 

wide x 

unlimited 

Use 

Copper pipes 

max 88.9mm 

Ø x 3mm thick 

(100kg/m³ 

mineral fibre 


x 40mm thick) 

(2 

Copper pipes 

max 54mm Ø 

x 3mm thick 

(45 - 100kg/m³ 

Armaflex 

AF/SH 



x 9 – 31mm 

thick) (2) 

uPVC pipes 

up to 110mm 

Ø x 8.2mm 

thick 

(1.8mm min 


for pipes ≤ 

50mmØ & 

2.2mm for 

pipes ≤ 

110mm Ø) (3) 

HDPE pipes 

up to 110mm 

Ø x 10mm 

thick (2.7mm 

min wall 

thickness) (3) 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

120 120 

120 90 

120 120 

120 120 

Cert. 

No. 

Notes 

For CP657 Blocks with CP651N mastic (floor application); 

1. Hilti CP657 Fire Stop Brick with a minimum thickness of 200mm and a nominal density of 270 ± 30kg/m³. If the minimum thickness of 

the concrete floor is 200mm, then the seal may be fitted directly into the opening in the floor. If the thickness is less than 200mm 

(minimum 150mm for floors) then the opening may either be lined with calcium silicate board, minimum 200mm wide x 25mm thick, or 

the opening increased to at least 200mm by fitting calcium silicate board, minimum 50mm wide x 25mm thick, around the opening. 

The board is fastened with steel screws into metal plugs at max 300mm centres. The boards may be fitted to the upper face of a floor. 

The calcium silicate board shall be Promatect H or equivalent. When fitted in a partition system, the cavity of the partition is closed 

around the opening with stud sections on all four sides. The opening is lined with calcium silicate board or a fire rated plaster board 

(with glass fibre reinforcement), min 200mm wide x 25mm thick. 

2. The metal pipes shall be fitted with a mineral wool sleeve that is either continuous through the seal or may be interrupted and butt up 

to the face of the seal on both faces. 

3. A square or ring of steel mesh must be fitted to the soffit of the penetration seal around the pipe. The mesh is typically1.5mm thick 

with a mesh size of 9mm x 9mm. the width of the mesh is at least 50mm on all sides of the pipe. The mesh is fastened to the CP657 

bricks with four steel self tapping screws, nominally M6 x 150mm long, equally spaced around the pipe. 

4. All services passing through the penetration seal system must be supported on both sides of the seal within 500mm from the face of 

the seal so that the weight of the services is not taken by the seal system. 


114 20 Nov 2011



Penetration Gap seals - CP670 Fire Safety System (unframed double layer 100mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Floor 150 LW Concrete 

650kg/m³ 


650kg/m³ 


650kg/m³ 


650kg/m³ 


650kg/m³ 


650kg/m³ 


650kg/m³ 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Fire 

Resistance 

Integrity 

(E) 

Fire 

Resisitance 

Insulation 

(I) 

Cert. 

No. 

N/A 120 120 090a/10 

Cable Trays 

500 x 60 mm 

(4)(5) 

Cable Trays 

300 x 60 mm 

(4)(5) 

CP644 Collars 

(surface 

mounted) 

pipes 160 

mm Ø x 1.8 - 

14.6 mm thick 

(3) 

Steel Pipes 

32mm Ø x 2.6 

– 4.0 mm 

thick 

(Insulated with 

40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 500 x 

30mm thick) 

(6) 

Steel Pipes 

159 Ø x 4.0 – 

14.2 mm thick 

or 168.3mm Ø 

x 4.0mm thick 

(Insulated 40 

– 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 800 x 

30mm thick) 

(6) 

Steel Pipe 

168.3mm Ø x 

14.2 mm thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

120 120 

120 120 

120 120 

120 120 

120 120 

120 120 

20 Nov 2011 115



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 


650kg/m³ 

Aperture 

Size 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm long 

(1). 

Penetration 

Type 

Copper Pipe 

88.9mm Ø x 

1.8 mm thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 800 x 

40mm thick) 

(6) 

Fire 

Resistance 

Integrity 

(E) 

Fire 

Resisitance 

Insulation 

(I) 

120 120 

Cert. 

No. 

Notes: 

1. CP670 Fire Safety System consists of 2 x 50mm pre-coated CP670 Fire Safety Board’s having a density of 150kg/m3 & coated with 

CP 670 Fire Safety Coating nominally 1.0mm thick extending beyond the perimeter of the seal onto surface of surrounding 

construction by 12.5mm unless otherwise stated. 



3. CP644 Collars are approved surface mounted to the under side of the floor with High Density Polyethylene (PE - HD) & Polyvinyl 

chloride -Un-plasticised (PVC-U) pipes only. 

4. All cables & cable trays required to provide 120 minutes insulation and integrity must include a 150mm coat back of CP670 Fire 

Safety Coating. 


6. Rockwool Heizungsrohrschale 800 mineral wool insulation (1000mm long x 40mm thick) must be applied from each face of the LW 

concrete floor. 


Penetration Gap Seals - CP670 Fire Safety System (unframed double layer 100mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Wall 135 Steel framed 

drywall 



drywall 



drywall 



drywall 


Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Fire 

Resistance 

Integrity 

(E) 

Fire 

Resistance 

Insulation 

(I) 

Cert. 

No. 

N/A 120 120 090a/10 

Cable Trays 

500 x 60 mm 

(4)(5) 

Cable Trays 

300 x 60 mm 

(4)(5) 

CP644 Collars 

(surface 

mounted) 

pipes 160 mm 

Ø x 1.8 -14.6 

mm thick (3) 

120 120 

120 120 

120 120 

116 20 Nov 2011



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 


drywall 



drywall 



drywall 



drywall 


Aperture 

Size 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Maximum 

aperture 

size 1000 

mm wide 

x 2000 

mm high 

(1). 

Penetration 

Type 

Steel Pipes 

32mm Ø x 2.6 

– 4.0 mm thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 500 x 

30mm thick) 

(6) 

Steel Pipes 

159 Ø x 4.0 – 

14.2 mm thick 

or 168.3mm Ø 

x 4.0mm thick 

Insulated with 

40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 800 x 

30mm thick) 

(6) 

Steel Pipe 

168.3mm Ø x 

14.2 mm thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

Copper Pipe 

88.9mm Ø x 

1.8 mm thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 800 x 

40mm thick) 

(6) 

Fire 

Resistance 

Integrity 

(E) 

Fire 

Resistance 

Insulation 

(I) 

120 120 

120 120 

120 120 

120 120 

Cert. 

No. 

Notes: 

1. CP670 Fire Safety System consists of 2 x 50mm pre-coated CP670 Fire Safety B|oard’s having a density of 150kg/m3 & coated with 

CP 670 Fire Safety Coating nominally 1.0mm thick extending beyond the perimeter of the seal onto surface of surrounding 

construction by 12.5mm unless otherwise stated. 



3. CP644 Collars are approved surface mounted to the steel framed drywall partition with High Density Polyethylene (PE - HD) & 

Polyvinyl chloride -Un-plasticised (PVC-U) pipes only. 

4. All cables & cable trays required to provide 120 minutes insulation and integrity must include a 150mm coat back of CP670 Fire 

Safety Coating. 


6. Rockwool Heizungsrohrschale 800 mineral wool insulation (1000mm long x 40mm thick) must be applied from each face of the 

partition. 


20 Nov 2011 117



Penetration Gap Seals - CP670 Fire Safety (unframed single layer 50mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Elements of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Floor 150 Reinforced 

concrete 


concrete 


concrete 


concrete 


concrete 


concrete 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Maximum 

aperture 

size 2200 

mm long x 

600 mm 

wide (1). 

Fire 

Resistance 

Integrity 

(E) 

Fire 

Resistance 

Insulation 

(I) 

Cert. 

No. 

N/A 60 60 090a/10 

Cable trays up 

to 500mm 

wide by 60mm 

deep (4) (5) 

Steel Pipes 

up to 168mm 

Ø x 14.2 mm 

thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

Copper Pipes 

up to 88.9mm 

Ø x 2.5 mm 

thick 


40 – 50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

CP643N 

Collars 

(surface 

mounted) 

PVC-U pipes 

32 - 110 mm 

Ø and up to 

8.2 mm wall 

thickness (3) 

CP643N 

Collars 

(surface 

mounted) PE 

pipes 32 - 110 

mm Ø and up 

to 10 mm wall 

thickness (3) 

60 60 

60 60 

60 60 

60 60 

60 60 

Notes: 

1. The CP 670 Fire Safety Board System consists of 1 x 50mm pre-coated mineral wool board having a density of 160kg/m³ & coated 

with a layer of CP 670 Fire Safety Coating applied to both faces to a thickness of 0.7mm,. The boards were supplied 1200mm long x 

600mm wide and were cut to fit. Once in place the boards should be additionally sealed at their edges with CP 606 mastic. Provided 

the CP 670 Fire Safety Board System is restricted to 600mm wide its length can be unrestricted. 



3. CP643N Collars are approved surface mounted to the under side of the floor with Polyethylene (PE) & Polyvinyl chloride -Unplasticised 

(PVC-U) pipes only. 

4. All cables & cable trays required to provide 60 minutes insulation and integrity must include a 150mm coat back of CP670 Fire Safety 

Coating. 

5. Cables (15 - 78mm Ø Copper core 1.5 - 185mm² & 52mm Ø Aluminium core 185mm²) may be individual or bunched where they 

penetrate the CP 670 Fire Safety System. 

6. Rockwool Heizungsrohrschale 800 mineral wool insulation (1000mm long x 40mm thick) must be applied from each face of the 

partition. 

118 20 Nov 2011




Penetration Gap Seals - CP670 Fire Safety Systems (unframed double layer 100mm) 

Product 

Name 

Aperture 

Size 

Penetration 

Type 

CP 670 

Fire 

Safety 

System 

(1) 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 


concrete 


concrete 


concrete 


concrete 


concrete 


concrete 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Maximum 

aperture 

size 2100 

mm long x 

1200 mm 

wide (1). 

Fire 

Resisitance 

Integrity (E) 

Fire 

Resisitance 

Insulation 

(I) 

Cert. 

No. 

N/A 60 60 090a/10 

Cable trays 

up to 500mm 

wide by 

60mm deep 

(4) (5) 

Steel Pipes 

up to 168mm 

Ø x 14.2 mm 

thick 

(Insulated 

with 40 – 

50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

Copper Pipes 

up to 88.9mm 

Ø x 2.5 mm 

thick 

(Insulated 

with 40 – 

50kg/m² 

Rockwool 800 

mineral fibre 

jacket 1000 x 

40mm thick) 

(6) 

CP643N 

Collars 

(surface 

mounted) 

PVC-U pipes 

32 - 160 mm 

Ø and up to 

11.9 mm wall 

thickness (3) 

CP643N 

Collars 

(surface 

mounted) PE 

pipes 32 - 

160 mm Ø x 

up to 14.6 

mm wall 

thickness (3) 

60 60 

60 60 

60 60 

60 60 

60 60 

Notes: 

1. The CP 670 Fire Safety Board System consists of 2 x 50mm pre-coated mineral wool board having a density of 160kg/m³ & coated 

with a layer of CP 670 Fire Safety Coating applied to both faces to a thickness of 0.7mm. The boards were supplied 1200mm long x 

600mm wide and were cut to fit. Once in place the boards should be additionally sealed at their edges with CP 606 mastic. Provided 

the CP 670 Fire Safety Board System is restricted to 1200mm wide its length can be unrestricted. 



3. CP643N Collars are approved surface mounted to the under side of the floor with Polyethylene (PE) & Polyvinyl chloride -Unplasticised 

(PVC-U) pipes only. 

20 Nov 2011 119



4. All cables & cable trays required to provide 60 minutes insulation and integrity must include a 150mm coat back of CP670 Fire Safety 

Coating. 

5. Cables (15 - 78mm Ø Copper core 1.5 - 185mm² & 52mm Ø Aluminium core 185mm²) may be individual or bunched where they 

penetrate the CP 670 Fire Safety System. 

6. Rockwool Heizungsrohrschale 800 mineral wool insulation (1000mm long x 40mm thick) must be applied from each face of the floor. 

MCT Brattberg AB 

SE 37192 Karlskrona, Sweden 

Tel: +46 (0) 455 451 60 • Fax: +46 (0) 455 451 28 

E-mail: info@mctbrattberg.com • Website: www.mctbrattberg.com 

UK Office: 

MCT Brattberg Ltd, Commerce Street, Carrs Industrial Estate, Haslingden BB4 5JT, United Kingdom 

Tel: +44 (0)1706 244890 • Fax: +44 (0)1706 244891 

E-mail: info@mctbrattberg.co.uk • Website: www.mctbrattberg.co.uk 


Product Name Use Element of 

Construction 

RGB 2, 4, 6, 8 & RGB 180, 240 & 360 Cables Concrete or masonry 

Floor 

Steel pipes Concrete or masonry 

Floor 

Cables Concrete or masonry 

Wall 


Wall 

RGBO 2, 4, 6, 8 & RGBO 180, 240 & 360 Cables Concrete or masonry 

Floor 


Floor 


Wall 


Wall 

RGP 50, 70, 100, 150, 200 & 300 Cables Concrete or masonry 

Floor 


Floor 


Wall 


Wall 

RGPO 50, 70, 100, 150, 200 & 300 Cables Concrete or masonry 

Floor 


Floor 


Wall 

Steel pipe Concrete or masonry 

Wall 


(min) 

Integrity 


(min) 

Insulation 

Cert. No. 

240 120 628a/01 

240 60 

240 60 

240 60 

240 120 628a/02 

240 60 

240 60 

240 60 

360 120 628a/03 

240 60 

360 120 

240 60 

360 120 628a/04 

240 60 

360 120 

240 60 

Note: 

Please refer to manufacturer’s product data for maximum aperture sizes and installation details. 

120 20 Nov 2011





Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022b(3) to LPS 1132: Issue 4 

Product Name Application Cavity 

Width 

(mm) 

Rockwool Firepro TCB Cavity 

Barrier 

Masonry/timber 

frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

cavity walls 


frame and 

masonry 

Barrier 

Size 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resisitance 

(min) 

Insulation 

Cert. 

No. 

50 - 55 65 X 65 60 30 022b/04 

56 - 65 75 x 75 60 30 

66 - 75 85 x 85 60 30 

76 - 80 90 x 90 60 30 

81 - 90 100 x 

100 

91 - 100 110 x 

110 

101 - 

110 

111 - 

120 

121 - 

130 

131 - 

140 

120 x 

120 

130 x 

130 

140 x 

140 

150 x 

150 

60 30 

60 30 

60 30 

60 30 

60 30 

60 30 

cavity walls 

Timber frame 50 - 55 65 x 65 30 30 

Timber frame 56 - 65 75 x 75 30 30 

Timber frame 66 - 75 85 x 85 30 30 

Timber frame 76 - 80 90 x 90 30 30 

Timber frame 81 - 90 100 x 

30 30 

100 


30 30 

110 

Timber frame 101 - 120 x 

30 30 

110 120 


30 30 

120 130 


30 30 

130 140 


30 30 

140 150 

Timber frame 50 - 55 75 x 75 60 30 

Timber frame 56 - 65 75 x 75 60 30 

20 Nov 2011 121



Product Name Application Cavity 

Width 

(mm) 

Barrier 

Size 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resisitance 

(min) 

Insulation 

Timber frame 66 - 75 85 x 85 60 30 

Timber frame 76 - 80 90 x 90 60 30 


60 30 

100 


60 30 

110 


60 30 

110 120 


60 30 

120 130 


60 30 

130 140 


60 30 

140 150 


60 60 

100 


60 60 

110 


60 60 

110 120 


60 60 

120 130 

Timber frame 121 - 

130 

140 x 

140 

60 60 

Cert. 

No. 

Notes: 

1. Rockwool Firepro TCB Cavity Barrier is designed for use between the leaves of a masonry cavity wall, timber frame construction, or 

between a timber frame inner leaf and masonry outer leaf. 

2. Barriers can be installed vertically or horizontally. 

3. Refer to manufacturer’s technical literature for fixing details. 


Product Name 

Cavity 

Width 

(mm) 

Slab Size 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Cert. No. 

Rockwool Firepro SP 60 Firestop Slab 50 - 400 900 x 650 x 75 60 60 022b/01 

Rockwool Firepro SP 120 Firestop Slab 50 - 400 900 x 650 x 90 120 120 022b/02 

Notes: 

1. This product is suitable for sealing gaps between a concrete or composite concrete/metal floors and an adjacent masonry, 

cladding/panel system with non-combustible core or curtain wall, or between the leaves of a masonry cavity wall. 

2. For cavity widths of 250mm or more, joints between adjacent lengths of firestops should be sealed on the top surface with aluminium 

foil tape. 

3. Refer to manufacturer's technical literature for fixing details. 


Product Name 

Rockwool Firepro 

Linear and 

Trapezoidal 

Firestop Systems 

Product 

Type(s) 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Wall 

Width 

(mm) 

Firestop 

Width 

(mm) 

Application 

100 100 Profiled metal 

deck over block 

work wall, 

with profile 

running across 

or along the wall 


deck over block 

work wall, with profile 



Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Cert. 

No. 

120 120 022b/03 

180 180 

122 20 Nov 2011



Product Name 

Product 

Type(s) 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

& Linear 

Firestop 2 

Trapezoidal 

Firestop 3B 

Trapezoidal 

Firestop 3B 

Trapezoidal 

Firestop 3B 

Wall 

Width 

(mm) 

Firestop 

Width 

(mm) 

Application 

200 200 Profiled metal deck 

over blockwork 

wall, with profile 




with lightweight 

concrete over wall, 

with profile running 

across or along the wall 


deck with lightweight 

concrete over wall, 

with profile running 

across the wall 


with lightweight concrete 

over wall, with profile 

running along the wall 


with lightweight concrete 

over wall, with profile 

running across or 

along the wall (1) 


with or without lightweight 

concrete over Steel 

Universal Beam, with 

profile running across the 

beam. (1) 


with or without 

lightweight concrete 

over Steel Universal Beam, 

with profile running across 

the beam. (1) 






beam. (1) 

N/A 100 Profiled metal deck 



Universal 

Beam, with profile 

running across the beam. 

(1) 






beam. (1) 




Universal 

Beam, with profile running 

across the beam. (1) 

Linear Firestop 2 100 100 Concrete deck over 

Blockwork wall 





Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

240 240 

120 120 

180 180 

240 240 

240 240 

120 120 

180 180 

240 240 

120 120 

180 180 

240 240 

120 120 

180 180 

240 240 

Cert. 

No. 

20 Nov 2011 123



Product Name 

Product 

Type(s) 

Trapezoidal 

Firestop 3B & 

Linear Firestop 2 

Trapezoidal 

Firestop 3B & 


Trapezoidal 

Firestop 3B & 


Linear Firestop 

3A 


3A 


3A 


3A 


3A 


3A 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 

Wall 

Width 

(mm) 

Firestop 

Width 

(mm) 

Application 

100 100 Profiled concrete deck over 

blockwork wall, with profile 

running across or along the 

wall. 




wall. 




wall. 

100 300 Concrete deck over 

blockwork wall, with 

extended firestopping (2) 
















100 200 Profiled Metal deck over 

blockwork wall with 

extended firestopping, with 


wall. (2) 





wall. (2) 





wall. (2) 





wall. (2) 





wall. (2) 





wall. (2) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

120 120 

240 240 

240 240 

180 180 

240 240 

240 240 

180 180 

240 240 

240 240 

180 180 

180 180 

240 240 

180 180 

240 240 

240 240 

Cert. 

No. 


3A & 

Trapezoidal 

Firestop 3B 





wall. (2) 

180 180 

124 20 Nov 2011



Product Name 

Product 

Type(s) 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 


3A & 

Trapezoidal 

Firestop 3B 

Wall 

Width 

(mm) 

Firestop 

Width 

(mm) 

Application 





wall. (2) 





wall. (2) 

100 400 Profiled metal deck with 

lightweight concrete over 

block wall, with the profile 

running across the wall. (2) 









100 400 Profiled Deck over 


Asymmetrical profiles, with 

the profile running along 

the wall. (2) 





the wall. (2) 





the wall. (2) 


blockwork wall 





Trapezoidal 100 100 Profiled metal deck with 

Firestop 3B & 



wall, with the profile 

Trapezoidal 

Firestop 3B & 


Trapezoidal 

Firestop 3B & 


running across the wall 









Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

240 240 

240 240 

180 180 

240 240 

240 240 

180 180 

240 240 

240 240 

120 0 

180 0 

240 0 

120 0 

180 0 

240 0 

Cert. 

No. 

Notes: 

1. The fire resistance of the BeamClad or ColumnClad system used for the fire protection of the beam must be the same as the fire 

resistance of the Linear and Trapezoidal Firestop systems. Where the beam has a wall underneath, the gap between the beam 

casing and the top of the wall should be packed with linear Firestop 2. 

2. Extended firestopping may need to be supported by fire resistant fixings to soffits to avoid edge sag, depending on overhang and 

soffit flatness. Supports are essential for extensions greater than 100mm. 

3. Where Linear Firestop 2 is used it must be compressed by at least 5% & where Trapezoidal Firestop 3B is used it must be tightly and 

accurate fit into trapezoidal profile. 

4. Where fire ratings apply to gaps over walls they must be constructed of dense aggregate blocks, lightweight aggregate concrete, clay 

bricks, or concrete blocks, which have a density of 400 Kg/m³ or greater. 

5. The maximum gap size allowed between the top of the wall and the soffit of the deck/floor is the thickness of the wall. 

6. Refer to manufacturer's technical literature for fixing details 

20 Nov 2011 125




Product 

Name 

FirePro 

Acoustic 

Intumescent 

Sealant 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Maximum 

Joint 

Width 

(mm) 


Fire Side 

Depth of 

Sealant 

(mm) 


Backing 

Material 

floor 230 AC/AC 50 25 Ethafoam 

50mm 

floor 230 Softwood/AC 25 12 Ethafoam 

0mm 

floor 230 Hardwood/AC 50 25 Ethafoam 

50mm 

floor 230 Steel/AC 50 25 Ethafoam 

50mm 


40mm 


mm 

floor 250 AC/AC 20 Polyethylene 

20mm 


50 x 25mm 


0mm 


25mm 


15mm 


25mm 

wall 150 AC/AC 30 30 Polyethylene 

15 x 15 


10 x 10 


10 x 15 


10 x 15 


15 x 15 


30 x 15 

wall 200 AC/AC 50 25 Ethafoam 

50mm 

wall 200 Hardwood/AC 50 25 Ethafoam 

50mm 

wall 200 Softwood/AC 25 12 Ethafoam 

30mm 

wall 200 Steel/AC 50 25 Ethafoam 

50mm 


40mm 


25mm 


25mm 


25mm 

wall 250 AC/AC 20 Polyethylene 

20mm 


40mm 


10mm 


25mm 


Non-fire Side 

Depth of 

Sealant 

Configeration: 

Non-fire Side 

Depth of 

Sealant 

(mm) 

Fire 

Resistance 

(mm) 

Integrity 

(E) 

Fire 

Resistance 

(mm) 

Insulation 

(I) 

Cert. 

No. 

155 105 022b/05 

51 44 

47 47 

72 62 

243 65 

243 29 

10 155 47 

25 240 92 

6 240 207 

15 240 73 

53 53 

243 29 

30 265 265 

15 265 230 

10 265 265 

200 166 

227 227 

240 233 

245 82 

96 93 

55 54 

77 39 

243 44 

243 29 

40 29 

243 16 

10 240 122 

20 240 95 

10 240 240 

20 240 126 

Note: 

AC - Aerated Concrete. 

Ethafoam - Open cell polyethylene foam rod 

Please refer to Rockwool installation instructions for further details 


126 20 Nov 2011

Rockwool FirePro Ablative Coated Batt - Pipe Penetration 

Product 

Name 

Rockwool 

FirePro 

Ablative 

Coated Batt 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 



Element of 

Construction 

Material 

Wall 150 Block 

work/Concrete 

wall or 120min 

Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 

Aperture 

Size 

(mm) 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

Coated Seal Detail 

Batt 

(layers & 

Thickness) 

1 x 30mm Rockwool 

Insulated 

Fire Sleeve 

Penetration 

Type 

ABS 

O/D wall 

thickness 

range 

(mm) 

27 / 2.5 to 

110 / 12 

PVC 19 / 1.9 to 


Sleeve (7) 

Insulated 

Fire 

55 / 2.2 

PVC >55 / 2.2 


Sleeve (7) 

Insulated 

Fire 

to 

110 / 8.9 

PVC 110 / < 


Sleeve (7) 

Insulated 

Fire 

3.6 

HDPE 110 / 4.2 


Sleeve (7) 

Insulated 

Fire 

to 

160 / 6.2 

PP >22 / 1.2 


Sleeve (7) 

Insulated 

Fire 

to 

160 / 10 

Fire 

Resistance 

Integrity / 

Insulation 

Cert. 

No. 

120 / 60 022b/06 

90 / 60 

60 / 60 

120 / 30 

90 / 60 

60 / 60 

PP 22 / 1.2 120 / 120 


Sleeve (7) 

Insulated 

Fire 

1 60mm Unlagged (8) Steel 17.1 / 2.3 

to 

168.3 / 7.1 

1 x 60mm Unlagged (8) Copper 15.0 / 0.7 

to 

108 / 1.5 

1 x 60mm Lagged with 

Fire Tube/ 

Conlit pipe 

sections 

1 x 60mm Lagged 

with Fire 

Tube/Conlit 

pipe 



Fire 

Tube/Conlit 

pipe 


Steel 88.9 / 4.0 

to 

164 / 6.4 

Copper 15.0 / 0.5 

to 

108 / 1.5 

120 / 0 

120 / 0 

120 / 60 

120 / 60 

Copper 50 / 1.8 120 / 120 

20 Nov 2011 127



Product 

Name 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Wall 150 Block work 

or Concrete 

Wall 

Wall 150 240min Block 

work 

or Concrete 

wall 

Wall 150 240min 

Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 


Block work or 

Concrete wall 

Floor 150 240min 

Concrete Floor 







Aperture 

Size 

(mm) 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

Coated Seal Detail 

Batt 

(layers & 

Thickness) 


500mm 

long 

x 40 thick 

Rockwool 

800 

insulation 

or Lagged 

with 

Fire 

Tube/Conlit 

pipe 


Penetration 

Type 

O/D wall 

thickness 

range 

(mm) 

Steel 88.9 / 4.0 

to 

170 / 8.0 

1 x 60mm Unlagged (8) Steel 17.1 / 2.3 

to 

168.3 / 7.1 


to 

108 / 1.5 


Fire 

Tube/Conlit 

pipe 



Fire 

Tube/Conlit 

pipe 


2 x 50mm 

(with 

100mm 

air gap) 

2 x 60mm 

(with 85 

mm 

air gap) 

2 x 50mm 

(with 

100mm 

air gap) 

2 x 50mm 

(with 

100mm 

air gap) 

2 x 50mm 

(with 

100mm 

air gap) 

Steel 17.1 / 2.3 

to 

168.3 / 7.1 

Copper 15.0 / 0.7 

to 

108 / 1.5 

Unlagged (8) Steel 17.1 / 2.3 

to 

168.3 / 7.1 

Unlagged (8) Steel 17.1 / 2.3 

to 

168.3 / 7.1 

Unlagged (8) Copper 15.0 / 0.7 

to 

108 / 1.5 

Lagged with 

Fire 

Tube/Conlit 

pipe 


Lagged with 

Fire 

Tube/Conlit 

pipe 

Steel 17.1 / 2.3 

to 

168.3 / 7.1 

Copper 15.0 / 0.7 

to 

108 / 1.5 


1 x 60mm Unlagged (8) Steel 17.1 / 2.3 

to 

168.3 / 7.1 


to 

108 / 1.5 

1 x 60mm Lagged with Steel 17.1 / 2.3 

Fire 

to 

Tube/Conlit 

168.3 / 7.1 

pipe 



Fire 

Tube/Conlit 

pipe 


Copper 15.0 / 0.7 

to 

108 / 1.5 

Fire 

Resistance 

Integrity / 

Insulation 

120 / 120 

240 / 0 

240 / 0 

180 / 120 

240 / 60 (6) 

240 / 0 

240 / 0 

240 / 0 

180 / 120 

240 / 60 (6) 

240 / 0 

240 / 0 

240 / 120 

240 / 120 

Cert. 

No. 

Notes 

1. The Fire Performance of the system will be dependant on the seal detail and Pipe type/ diameter. References should be made to 

manufactures literature and Chiltern International Fire Ltd Assessment Report: Chilt/A08152 rev B for further information. 

2. For Lightweight flexible wall constructions the partition must be a minimum overall thickness of 130mm and be faced on each side 

with two layers of type F 15mm thick fire rated plasterboard or equivalent 

3. For Rigid wall constructions comprising of 150mm, 200mm or 215mm thick lightweight aerated concrete or block work shall have a 

minimum density of 750kg/m³. 

4. For Rigid floor constructions comprising of 150mm lightweight aerated concrete shall have a minimum density of 800kg/m³. 

5. Rockwool FirePro Ablative Coated batt has a density of 180kg/m³ comprising of a rock fibre core coated on both faces with 0.6 - 

0.8mm thick (1mm max) Rockwool FirePro Ablative coating, friction fitted centrally within the thickness of the wall and sealed to the 

construction on both faces with a 30mm x 30mm fillet of Rockwool Acoustic Intumescent Sealant. 

6. 120 minutes insulation performance can be achieved using 50mm thick Fire Tube/Conlit seals. 

7. Rockwool Insulated Fire sleeves must be fitted on all plastic pipes (30mm thick for pipe Ø up to 110mm and 35mm thick for pipe Ø 

above 110mm) as they pass by the Rockwool Ablative coated batt and protrude from each face by 45mm. The sleeve shall be 

sealed into position with a 15mm x 15mm fillet of Rockwool Acoustic Intumescent sealant on each face. 

8. Unlagged metal pipes must be sealed with Rockwool Acoustic and Intumescent sealant on both sides of the penetration. 

128 20 Nov 2011



Certificate No: 022b(5) to LPS1132: Issue 4 

Rockwool FirePro Ablative coated Batt - Cable Penetrations 

Product 

Name 

Rockwool 

FirePro 

Ablative 

Coated Batt 

Element of 

Constuction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work/Concrete 


Lightweight 

flexible 

supporting 

construction 


work or 

Concrete wall 


work or 

Concrete wall 


work or 

Concrete wall 


work or 

Concrete wall 


work or 

Concrete wall 


work or 

Concrete wall 










Concrete or 

Block work 

Wall 


lightweight 

flexible 

supporting 

construction 

Aperture 

Size 

(mm) 

1200 x 

600 

1200 x 

600 

1200 x 

1200 

1200 x 

1200 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

1200 x 

600 

Coated 

Batt 

(Layers 

& 

Thickness) 

Seal 

Details 

1 x 60mm 4mm conlit 

bandage 

1 x 60mm 4mm Conlit 

bandage 


bandage 


bandage 


or 2 x 50mm bandage 

(100mm air 

gap) 


or 2 x 50mm bandage (7) 

(100mm air 

gap) 


or 2 x 50mm bandage 

(100mm air 

gap) 



(100mm air 

gap) 



(100mm air 

gap) 


or 2 x 50mm Acoustic 

(100mm air Intumescent 

gap) Sealant fillet 


bandage (7) 


bandage 


bandage 


bandage 


bandage 


bandage 

Sheathed 

Cables / 

Unsheathed 

Cables Type 

(6) 

All Sheathed 

Cabel types 

PVC 

Sheathed 

Cable types 

All Sheathed 

Cable types 

PVC 

Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

Cable types 

All Sheathed 

cables 

(excluding 

telecoms 

cables) 

Sheathed 

telecoms 

cables 

PVC 

Unsheathed 

cable types 

PVC 

Unsheathed 

cable types 

PVC 

Unsheathed 

cable types 

Cable 

Diameter 

(mm) 

Fire 

Resisitance 

Integrity / 

Insulation 

Cert. 

No. 

< 21 120 / 60 022b/06 

50 120 / 60 

< 21 90 / 60 

50 90 / 60 

< 21 120 / 60 

< 21 240 / 120 

22 to 50 60 / 60 

22 to 50 240 / 60 

51 to 80 120 / 60 

< 21 120 / 60 

< 21 240 / 60 

< 21 240 / 60 

< 21 120 / 60 

10 to 24 240 / 30 

10 to 24 120 / 30 

10 to 24 120 / 30 

Notes 

1. The Fire Performance of the system will be dependant on the seal detail and cable type/ diameter. References should be made to 

manufactures literature and Chiltern International Fire Ltd Assessment Report: Chilt/A08152 rev B for further information. 

2. For Lightweight flexible wall constructions the partition must be a minimum overall thickness of 130mm and be faced on each side 

with two layers of type F 15mm thick fire rated plasterboard or equivalent 

3. For Rigid wall constructions comprising of 150mm, 200mm or 215mm thick lightweight aerated concrete or block work shall have a 

minimum density of 750kg/m³. 

20 Nov 2011 129




5. Rockwool Ablative Coated batt has a density of 180kg/m³ comprising of a rock fibre core coated on both faces with 0.6 - 0.8mm thick 

(1mm max) Rockwool FirePro Ablative coating, friction fitted centrally within the thickness of the wall and sealed to the construction 

on both faces with a 30mm x 30mm fillet of Rockwool Acoustic Intumescent Sealant. 

6. All Cables shall be supported by steel ladders up to 340mm wide x 80mm deep or steel trays (perforated and un-perforated) up to 

460mm wide x 25mm deep at all performance periods. 

7. An Integrity performance of 240 minutes can be achieved if a 6 x 1mm layer Conlit ‘bandage’ is used which extends 300mm from 

each face of the Rockwool Ablative Coated batt. 

8. Cables may be individual or bundled where they penetrate the Rockwool FirePro Ablative Coated Batt system. Cable bundles are 

limited dependant on size and type of cables and sealing method, reference must be made to Chiltern International Fire Ltd 

Assessment Report: Chilt/A08152 rev B for details. 


Rockwool Ablative Coated Batt - Blank Seals 

Product Name Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Rockwool FirePro 

Ablative Coated Batt 

Element of 

Construction 

Material 

Aperture 

Size 

(mm) 

Wall 150 Lightweight 

block work 

wall 


aerated 


Wall 215 Masonry wall 1200 x 

600 

Wall 130 

(Minimum) 

120 minute 

plasterboard 


Coated 

Batt 

(Layers & 

Thickness) 

Fire 

Resistance 

Integrity / 

Insulation 

Cert. 

No. 

600 x 600 1 x 50mm 240 / 30 022b/06 

600 x 600 1 x 50mm 240 / 120 

1200 x 

600 

2 x 50mm 240 / 240 

(with 

100mm 

air gap) 

1 x 60mm 120 / 120 

Notes 

1. Rockwool Ablative Coated batt has a density of 180kg/m³ comprising of a rock fibre core coated on both faces with 0.6 - 0.8mm thick 

(1mm max) Rockwool FirePro Ablative coating, friction fitted centrally within the thickness of the wall and sealed to the construction 

on both faces with a 30mm x 30mm fillet of Rockwool Acoustic Intumescent Sealant. 

2. For Rigid wall constructions comprising of 150mm or 215mm thick lightweight aerated concrete or block work shall have a minimum 

density of 750kg/m³. 


130 20 Nov 2011


STRUCTURAL STEEL FIRE PROTECTION 

The protection of the structural integrity of a building is important for life safety of the occupants, fire fighters 

and for the cost-effective repair of the building post fire. When a building is involved in a fire, structural 

steelwork can resist the damaging effects of the high temperatures generated if suitably protected. 

20 Nov 2011 131


LPS 1107 STRUCTURAL STEEL FIRE PROTECTION - BOARD AND CEMENTITIOUS COVERINGS 

This section covers structural steel fire protection with use of board or cementitious coverings approved to 

LPS 1107 Requirements, Tests and Methods of Assessment of Passive Fire Protection Systems for Structural 

Steelwork. 

British Gypsum 

Head Office, East Leake, Loughborough, Leicester LE12 6HX, United Kingdom 

Tel: +44 ( 0)844 8001991 • Fax: +44 (0)844 5618816 

E-mail: bgtechnical.enquiries@bpb.com • Website: www.british-gypsum.com 


Product 

Name 

Glasroc F 

FIRECASE 

Exposure 

Internal 

only 

Internal 

only 

Internal 

only 

Internal 

only 

Internal 

only 

Board 

Thickness 

(mm) 

Performance at 

a critical 

steel 

temperature 

550 0 c 

Hp/A 30min 


a critical 

steel 

temperature 

550 0 c 

Hp/A 60min 


a critical 

steel 

temperature 

550 0 c 

Hp/A 90min 


a critical 

steel 

temperature 

550 0 c 

Hp/A 120 min 

Cert. 

No. 

15 260 260 105 65 162a/01 

20 260 260 180 90 

25 260 260 260 100 

30 260 260 260 250 

35 260 260 260 260 

Note: 

The 30mm and 35mm thickness of protection can be in two separately fixed layers, i.e., 15mm + 15mm and 15mm + 20mm. 

Promat UK Ltd 


Tel: +44 (0)1344 381 300 • Fax: +44 (0)1344 381 301 

Website: www.promat-spray.co.uk 

Certificate No: 762b to LPS 1107: Issue 1 - BS 476: Part 21: 1987 

Cafco 300, required thickness when protecting I section beams and H section columns at a critical 

temperature of 350ºC 

Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of: 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 14 19 27 35 762b/01 

40 12 12 17 22 32 42 

50 12 14 19 25 36 48 

60 12 15 21 27 40 52 

70 12 16 23 29 43 56 

80 12 17 24 31 45 60 

90 12 18 25 33 48 62 

100 12 19 26 34 50 65 

110 12 19 27 35 51 67 

120 12 20 28 36 53 69 

130 12 20 29 37 54 71 

140 12 21 29 38 55 - 

132 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of: 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

150 12 21 30 39 56 - 

160 13 22 30 39 57 - 

170 13 22 31 40 58 - 

180 13 22 31 41 59 - 

190 13 22 32 41 60 - 

200 13 23 32 42 61 - 

210 13 23 33 42 61 - 

220 14 23 33 43 62 - 

230 14 23 33 43 62 - 

240 14 24 33 43 63 - 

250 14 24 34 44 63 - 

260 14 24 34 44 64 - 

270 14 24 34 44 64 - 

280 14 24 34 44 65 - 

290 14 24 35 45 65 - 

300 14 25 35 45 65 - 

310 14 25 35 45 66 - 

320 14 25 35 45 66 - 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 16 22 29 762b/01 

40 12 12 15 19 27 35 

50 12 12 17 22 31 40 

60 12 14 19 24 34 44 

70 12 15 20 26 36 47 

80 12 16 21 27 39 50 

90 12 16 23 29 41 53 

100 12 17 23 30 42 55 

110 12 18 24 31 44 57 

120 12 18 25 32 45 59 

130 12 19 26 33 47 60 

140 12 19 26 33 48 62 

150 12 20 27 34 49 63 

160 13 20 27 35 50 64 

170 13 20 28 35 50 65 

180 13 21 28 36 51 66 

190 13 21 29 36 52 67 

200 13 21 29 37 53 68 

210 14 21 29 37 53 69 

220 14 22 30 38 54 70 

230 14 22 30 38 54 70 

240 14 22 30 38 55 71 

250 14 22 30 39 55 72 

260 14 22 31 39 56 72 

270 14 23 31 39 56 - 

280 14 23 31 40 56 - 

290 14 23 31 40 57 - 

300 15 23 32 40 57 - 

20 Nov 2011 133



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

310 15 23 32 40 57 - 

320 15 23 32 40 58 - 

Cert. 

No. 


Cafco 300, required thickness when protecting I section beams with H section coloumns at a critical 


Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 15 21 27 762b/01 

40 12 12 14 18 25 33 

50 12 12 16 20 29 37 

60 12 13 17 22 32 41 

70 12 14 19 24 34 44 

80 12 14 20 25 36 47 

90 12 15 21 27 38 49 

100 12 16 22 28 40 52 

110 12 16 23 29 41 54 

120 12 17 23 30 42 55 

130 12 17 24 31 44 57 

140 12 18 25 31 45 58 

150 12 18 25 32 46 59 

160 12 19 26 33 47 61 

170 12 19 26 33 47 62 

180 12 19 26 34 48 62 

190 12 19 27 34 49 63 

200 12 20 27 35 49 64 

210 12 20 27 35 50 65 

220 13 20 28 35 50 66 

230 13 20 28 36 51 66 

240 13 20 28 36 51 67 

250 13 21 28 36 52 67 

260 13 21 29 37 52 68 

270 13 21 29 37 53 69 

280 13 21 29 37 53 69 

290 13 21 29 37 53 69 

300 13 21 29 38 54 70 

310 13 22 30 38 54 70 

320 13 22 30 38 54 71 


134 20 Nov 2011



Cafco 300, required thickness when protection I section beams and H section columns at a critical 


Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 13 19 25 762b/01 

40 12 12 13 16 23 30 

50 12 12 14 18 26 34 

60 12 12 16 20 29 38 

70 12 12 17 22 31 41 

80 12 13 18 23 33 44 

90 12 14 19 24 35 46 

100 12 14 20 26 37 48 

110 12 15 21 27 38 50 

120 12 15 21 27 39 51 

130 12 16 22 28 41 53 

140 12 16 23 29 42 54 

150 12 17 23 30 42 55 

160 12 17 24 30 43 57 

170 12 17 24 31 44 58 

180 12 17 24 31 45 58 

190 12 18 25 32 45 59 

200 12 18 25 32 46 60 

210 12 18 25 32 47 61 

220 12 18 26 33 47 62 

230 12 19 26 33 48 62 

240 12 19 26 33 48 63 

250 12 19 26 34 49 63 

260 12 19 27 34 49 64 

270 12 19 27 34 49 64 

280 12 19 27 35 50 65 

290 12 20 27 35 50 65 

300 12 20 27 35 50 66 

310 12 20 27 35 51 66 

320 12 20 28 35 51 66 




Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 18 23 762b/01 

40 12 12 12 15 21 28 

50 12 12 13 17 24 32 

60 12 12 14 19 27 35 

70 12 12 16 20 29 38 

80 12 12 17 21 31 41 

90 12 13 18 23 33 43 

100 12 13 18 24 34 45 

110 12 14 19 25 35 46 

120 12 14 20 25 37 48 

130 12 14 20 26 38 49 

140 12 15 21 27 39 51 

150 12 15 21 27 40 52 

20 Nov 2011 135



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

160 12 15 22 28 40 53 

170 12 16 22 28 41 54 

180 12 16 22 29 42 55 

190 12 16 23 29 42 56 

200 12 16 23 30 43 56 

210 12 17 23 30 44 57 

220 12 17 24 30 44 58 

230 12 17 24 31 45 58 

240 12 17 24 31 45 59 

250 12 17 24 31 45 59 

260 12 17 25 32 46 60 

270 12 18 25 32 46 60 

280 12 18 25 32 46 61 

290 12 18 25 32 47 61 

300 12 18 25 33 47 62 

310 12 18 25 33 47 62 

320 12 18 26 33 48 62 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 minn 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 17 22 762b/01 

40 12 12 12 14 20 26 

50 12 12 12 16 23 30 

60 12 12 13 17 25 33 

70 12 12 14 19 27 36 

80 12 12 15 20 29 38 

90 12 12 16 21 31 40 

100 12 12 17 22 32 42 

110 12 12 18 23 33 44 

120 12 13 18 23 34 45 

130 12 13 19 24 35 46 

140 12 13 19 25 36 47 

150 12 14 19 25 37 48 

160 12 14 20 26 38 49 

170 12 14 20 26 38 50 

180 12 14 21 27 39 51 

190 12 15 21 27 39 52 

200 12 15 21 27 40 52 

210 12 15 21 28 40 53 

220 12 15 22 28 41 54 

230 12 15 22 28 41 54 

240 12 15 22 29 42 55 

250 12 16 22 29 42 55 

260 12 16 22 29 42 56 

270 12 16 23 29 43 56 

280 12 16 23 29 43 57 

290 12 16 23 30 43 57 

300 12 16 23 30 44 57 

310 12 16 23 30 44 58 

136 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 minn 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

320 12 16 23 30 44 58 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 16 20 762b/01 

40 12 12 12 13 19 25 

50 12 12 12 15 22 28 

60 12 12 13 16 24 31 

70 12 12 14 18 26 34 

80 12 12 15 19 28 36 

90 12 12 15 20 29 38 

100 12 12 16 21 31 40 

110 12 12 17 22 32 42 

120 12 12 17 23 33 43 

130 12 13 18 23 34 44 

140 12 13 18 24 35 46 

150 12 13 19 24 35 47 

160 12 13 19 25 36 48 

170 12 14 19 25 37 48 

180 12 14 20 26 37 49 

190 12 14 20 26 38 50 

200 12 14 20 26 39 51 

210 12 14 21 27 39 51 

220 12 15 21 27 39 52 

230 12 15 21 27 40 52 

240 12 15 21 28 40 53 

250 12 15 21 28 41 53 

260 12 15 22 28 41 54 

270 12 15 22 28 41 54 

280 12 15 22 29 42 55 

290 12 16 22 29 42 55 

300 12 16 22 29 42 56 

310 12 16 22 29 43 56 

320 12 16 23 29 43 56 


20 Nov 2011 137





Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 15 20 762b/01 

40 12 12 12 13 18 24 

50 12 12 12 14 21 28 

60 12 12 12 16 23 31 

70 12 12 13 17 25 33 

80 12 12 14 18 27 35 

90 12 12 15 19 28 37 

100 12 12 15 20 29 39 

110 12 12 16 21 31 40 

120 12 12 16 22 32 42 

130 12 12 17 22 33 43 

140 12 12 17 23 33 44 

150 12 12 18 23 34 45 

160 12 13 18 24 35 46 

170 12 13 18 24 35 47 

180 12 13 19 24 36 47 

190 12 13 19 25 37 48 

200 12 13 19 25 37 49 

210 12 14 20 25 37 49 

220 12 14 20 26 38 50 

230 12 14 20 26 38 51 

240 12 14 20 26 39 51 

250 12 14 20 27 39 51 

260 12 14 20 27 39 52 

270 12 14 21 27 40 52 

280 12 14 21 27 40 53 

290 12 14 21 27 40 53 

300 12 15 21 28 40 53 

310 12 15 21 28 41 54 

320 12 15 21 28 41 54 




Product 

Cert. 

Name 

No. 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 13 18 762b/01 

40 12 12 12 12 16 22 

50 12 12 12 12 19 25 

60 12 12 12 14 21 28 

70 12 12 12 15 23 31 

80 12 12 12 16 24 33 

90 12 12 12 17 26 35 

100 12 12 13 18 27 36 

110 12 12 14 18 28 38 

120 12 12 14 19 29 39 

130 12 12 15 20 30 41 

140 12 12 15 20 31 42 

150 12 12 15 21 32 43 

138 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

160 12 12 16 21 33 44 

170 12 12 16 22 33 45 

180 12 12 16 22 34 45 

190 12 12 17 22 34 46 

200 12 12 17 23 35 47 

210 12 12 17 23 35 48 

220 12 12 17 23 36 48 

230 12 12 17 24 36 49 

240 12 12 18 24 37 49 

250 12 12 18 24 37 50 

260 12 12 18 24 37 50 

270 12 12 18 25 38 51 

280 12 12 18 25 38 51 

290 12 12 18 25 38 51 

300 12 12 18 25 39 52 

310 12 12 19 25 39 52 

320 12 12 19 26 39 53 

Cert. 

No. 


Cafco 300, required thickness when protecting hollow section beams and columns at a critical 


Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 15 19 28 36 762b/01 

40 12 13 18 23 33 44 

50 12 14 20 26 38 50 

60 12 16 22 29 42 55 

70 12 17 24 32 46 60 

80 12 18 26 34 49 64 

90 12 19 28 36 52 68 

100 12 20 29 37 54 71 

110 12 21 30 39 57 - 

120 13 22 31 41 59 - 

130 13 23 32 42 61 - 

140 14 24 33 43 63 - 

150 14 24 34 45 65 - 

160 14 25 35 46 66 - 

170 15 25 36 47 68 - 

180 15 26 37 48 70 - 

190 15 27 38 49 71 - 

200 16 27 39 50 - - 

210 16 28 39 51 - - 

220 16 28 40 52 - - 

230 17 29 41 53 - - 

240 17 29 41 54 - - 

250 17 30 42 54 - - 

260 17 30 42 55 - - 

270 17 30 43 55 - - 

280 18 30 43 55 - - 

290 18 30 43 56 - - 

300 18 31 43 56 - - 

310 18 31 44 56 - - 

Cert. 

No. 

20 Nov 2011 139






Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 13 16 23 30 762b/01 

40 12 12 16 20 28 36 

50 12 13 18 23 32 42 

60 12 15 20 25 36 46 

70 12 16 22 27 39 50 

80 12 17 23 29 42 54 

90 12 18 24 31 44 57 

100 12 19 26 33 47 60 

110 12 20 27 34 49 63 

120 13 20 28 36 51 66 

130 13 21 29 37 53 68 

140 14 22 30 38 54 70 

150 14 23 31 39 56 - 

160 15 23 32 40 57 - 

170 15 24 33 41 59 - 

180 15 24 33 42 60 - 

190 16 25 34 43 62 - 

200 16 25 35 44 63 - 

210 16 26 35 45 64 - 

220 17 26 36 46 65 - 

230 17 27 37 47 67 - 

240 17 27 37 48 68 - 

250 17 28 38 48 69 - 

260 18 28 38 49 69 - 

270 18 28 39 49 70 - 

280 18 28 39 49 70 - 

290 18 29 39 50 71 - 

300 18 29 39 50 71 - 

310 18 29 40 50 72 - 

Cert. 

No. 



temperature 450ºC 

Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 15 21 28 762b/01 

40 12 12 14 18 26 34 

50 12 12 17 21 30 39 

60 12 13 18 23 33 43 

70 12 15 20 25 36 47 

80 12 16 21 27 39 51 

90 12 17 23 29 41 54 

100 12 17 24 31 44 57 

Cert. 

No. 

140 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

110 12 18 25 32 46 59 

120 12 19 26 33 48 62 

130 12 20 27 34 49 64 

140 13 20 28 36 51 66 

150 13 21 29 37 52 68 

160 13 21 30 38 54 70 

170 14 22 30 39 55 72 

180 14 23 31 40 57 - 

190 14 23 32 40 58 - 

200 15 24 32 41 59 - 

210 15 24 33 42 60 - 

220 15 24 34 43 61 - 

230 15 25 34 44 63 - 

240 16 25 35 45 64 - 

250 16 26 35 45 65 - 

260 16 26 36 46 65 - 

270 16 26 36 46 66 - 

280 16 26 36 46 66 - 

290 16 26 37 47 67 - 

300 17 27 37 47 67 - 

310 17 27 37 47 67 - 

Cert. 

No. 




Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 14 20 25 762b/01 

40 12 12 13 17 24 31 

50 12 12 15 19 27 36 

60 12 12 17 21 31 40 

70 12 13 18 23 33 44 

80 12 14 20 25 36 47 

90 12 15 21 27 38 50 

100 12 16 22 28 40 53 

110 12 17 23 29 42 55 

120 12 17 24 31 44 58 

130 12 18 25 32 46 60 

140 12 18 26 33 47 62 

150 12 19 26 34 49 64 

160 12 20 27 35 50 65 

170 12 20 28 36 52 67 

180 13 21 29 37 53 69 

190 13 21 29 38 54 71 

200 13 21 30 38 55 72 

210 13 22 31 39 56 - 

220 14 22 31 40 57 - 

230 14 23 32 41 59 - 

240 14 23 32 41 60 - 

250 14 24 33 42 61 - 

260 14 24 33 42 61 - 

270 15 24 33 43 62 - 

Cert. 

No. 

20 Nov 2011 141



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

280 15 24 34 43 62 - 

290 15 24 34 43 62 - 

300 15 24 34 44 63 - 

310 15 25 34 44 63 - 

Cert. 

No. 




Product 

Name 

Cafco 

300 

Section 

Factor 

(HP/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 13 18 24 762b/01 

40 12 12 12 15 22 29 

50 12 12 14 18 25 33 

60 12 12 15 20 28 37 

70 12 12 17 22 31 41 

80 12 13 18 23 33 44 

90 12 14 19 25 36 47 

100 12 14 20 26 38 49 

110 12 15 21 27 39 51 

120 12 16 22 28 41 54 

130 12 16 23 29 43 56 

140 12 17 24 30 44 58 

150 12 17 24 31 45 60 

160 12 18 25 32 47 61 

170 12 18 26 33 48 63 

180 12 19 26 34 49 64 

190 12 19 27 35 50 66 

200 12 20 28 36 52 67 

210 12 20 28 36 53 69 

220 12 20 29 37 54 70 

230 12 21 29 38 55 72 

240 13 21 30 38 56 - 

250 13 22 30 39 57 - 

260 13 22 31 39 57 - 

270 13 22 31 40 58 - 

280 13 22 31 40 58 - 

290 13 22 31 40 58 - 

300 13 22 31 41 59 - 

310 13 22 32 41 59 - 

Cert. 

No. 


142 20 Nov 2011





Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 17 22 762b/01 

40 12 12 12 14 21 27 

50 12 12 13 17 24 31 

60 12 12 14 18 27 35 

70 12 12 15 20 29 38 

80 12 12 17 22 31 41 

90 12 12 18 23 33 44 

100 12 13 19 24 35 46 

110 12 14 19 25 37 48 

120 12 14 20 26 38 50 

130 12 15 21 27 40 52 

140 12 15 22 28 41 54 

150 12 16 22 29 42 56 

160 12 16 23 30 44 57 

170 12 17 24 31 45 59 

180 12 17 24 31 46 60 

190 12 17 25 32 47 62 

200 12 18 25 33 48 63 

210 12 18 26 33 49 64 

220 12 18 26 34 50 65 

230 12 19 27 35 51 67 

240 12 19 27 35 52 68 

250 12 19 28 36 52 69 

260 12 20 28 36 53 70 

270 12 20 28 36 53 70 

280 12 20 28 37 54 71 

290 12 20 28 37 54 71 

300 12 20 29 37 54 72 

310 12 20 29 37 55 72 

Cert. 

No. 




Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 16 21 762b/01 

40 12 12 12 14 20 26 

50 12 12 12 16 23 30 

60 12 12 13 17 25 33 

70 12 12 15 19 28 36 

80 12 12 16 21 30 39 

90 12 12 17 22 32 42 

100 12 12 18 23 34 44 

110 12 13 19 24 35 46 

120 12 14 19 25 37 48 

130 12 14 20 26 38 50 

140 12 15 21 27 39 52 

150 12 15 21 28 41 54 

160 12 16 22 29 42 55 

Cert. 

No. 

20 Nov 2011 143



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

170 12 16 23 29 43 57 

180 12 16 23 30 44 58 

190 12 17 24 31 45 59 

200 12 17 24 32 46 61 

210 12 17 25 32 47 62 

220 12 18 25 33 48 63 

230 12 18 26 34 49 64 

240 12 18 26 34 50 66 

250 12 19 27 35 51 67 

260 12 19 27 35 51 67 

270 12 19 27 35 52 68 

280 12 19 27 36 52 68 

290 12 19 28 36 52 69 

300 12 19 28 36 53 69 

310 12 20 28 36 53 70 

Cert. 

No. 




Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 16 21 762b/01 

40 12 12 12 13 19 25 

50 12 12 12 15 22 29 

60 12 12 13 17 25 32 

70 12 12 14 18 27 35 

80 12 12 15 20 29 38 

90 12 12 16 21 31 40 

100 12 12 17 22 32 43 

110 12 12 18 23 34 45 

120 12 13 18 24 35 47 

130 12 13 19 25 37 48 

140 12 14 20 26 38 50 

150 12 14 20 27 39 52 

160 12 15 21 27 40 53 

170 12 15 22 28 41 55 

180 12 15 22 29 42 56 

190 12 16 23 29 43 57 

200 12 16 23 30 44 59 

210 12 16 24 31 45 60 

220 12 17 24 31 46 61 

230 12 17 24 32 47 62 

240 12 17 25 33 48 63 

250 12 17 25 33 49 64 

260 12 18 25 33 49 65 

270 12 18 26 34 49 65 

280 12 18 26 34 50 66 

290 12 18 26 34 50 66 

300 12 18 26 34 50 67 

310 12 18 26 35 51 67 

Cert. 

No. 

144 20 Nov 2011






Product 

Name 

Cafco 

300 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 300 

for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 12 12 12 12 14 19 762b/01 

40 12 12 12 12 17 23 

50 12 12 12 13 20 27 

60 12 12 12 15 22 30 

70 12 12 12 16 24 33 

80 12 12 13 17 26 35 

90 12 12 14 18 28 38 

100 12 12 14 19 30 40 

110 12 12 15 20 31 42 

120 12 12 16 21 33 44 

130 12 12 16 22 34 46 

140 12 12 17 23 35 48 

150 12 12 18 24 37 49 

160 12 12 18 25 38 51 

170 12 12 19 25 39 52 

180 12 12 19 26 40 54 

190 12 13 20 27 41 55 

200 12 13 20 27 42 56 

210 12 13 20 28 43 57 

220 12 13 21 28 44 59 

230 12 14 21 29 44 60 

240 12 14 22 30 45 61 

250 12 14 22 30 46 62 

260 12 14 22 30 47 63 

270 12 14 22 31 47 63 

280 12 14 23 31 47 64 

290 12 15 23 31 48 64 

300 12 15 23 31 48 65 

310 12 15 23 32 48 65 

Cert. 

No. 

Notes: 

1. LPCB Ref 726b/01 - approval for Cafco 300 without accelerator, profile application applied in several coats dependant on thickness. 

2. LPCB Ref 726b/01 - Cafco 300 approved from the following manufacturing sites only; Promat UK Ltd, Lawn Road Industrial Estate, 

Carlton-in-Lindrick, Worksop, Notts S81 9LB UK and Cafco International LLC, Sharjah, UAE. 


Cafco Mandolite CP2, required thickness when protecting I section beams and H section columns at a 

critical temperature of 350ºC 

Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 13 17 22 31 40 762b/02 

40 10 15 20 25 35 45 

50 10 16 21 27 38 49 

20 Nov 2011 145



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

60 11 17 23 29 40 52 

70 12 18 24 30 42 54 

80 12 18 25 31 44 56 

90 12 19 25 32 45 58 

100 13 19 26 33 46 59 

110 13 20 26 33 47 61 

120 13 20 27 34 48 62 

130 13 20 27 34 48 62 

140 13 21 28 35 49 63 

150 14 21 28 35 50 64 

160 14 21 28 35 50 65 

170 14 21 28 36 50 65 

180 14 21 29 36 51 66 

190 14 21 29 36 51 66 

200 14 22 29 37 52 66 

210 14 22 29 37 52 67 

220 14 22 29 37 52 67 

230 14 22 30 37 52 68 

240 14 22 30 37 53 68 

250 14 22 30 37 53 68 

260 14 22 30 38 53 68 

270 15 22 30 38 53 69 

280 15 22 30 38 53 69 

290 15 22 30 38 53 69 

300 15 22 30 38 54 69 

310 15 23 30 38 54 69 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 11 15 19 27 35 762b/02 

40 8 13 17 22 31 40 

50 9 14 19 24 34 44 

60 10 15 20 26 37 47 

70 10 16 22 27 38 50 

80 11 17 22 28 40 52 

90 11 17 23 29 41 54 

100 11 18 24 30 43 55 

110 12 18 24 31 44 56 

120 12 18 25 31 44 57 

130 12 19 25 32 45 58 

140 12 19 26 32 46 59 

150 12 19 26 33 46 60 

160 13 19 26 33 47 61 

170 13 20 27 34 47 61 

180 13 20 27 34 48 62 

190 13 20 27 34 48 62 

146 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

200 13 20 27 34 49 63 

210 13 20 27 35 49 63 

220 13 20 28 35 49 64 

230 13 20 28 35 50 64 

240 13 21 28 35 50 64 

250 13 21 28 35 50 65 

260 13 21 28 36 50 65 

270 13 21 28 36 51 65 

280 14 21 28 36 51 66 

290 14 21 29 36 51 66 

300 14 21 29 36 51 66 

310 14 21 29 36 51 66 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 10 13 17 24 31 762b/02 

40 8 11 15 20 28 36 

50 8 13 17 22 31 40 

60 9 14 18 23 33 43 

70 9 14 20 25 35 46 

80 10 15 20 26 37 48 

90 10 16 21 27 38 50 

100 10 16 22 28 40 51 

110 10 16 22 29 41 53 

120 11 17 23 29 41 54 

130 11 17 23 30 42 55 

140 11 17 24 30 43 56 

150 11 18 24 31 44 57 

160 11 18 25 31 44 57 

170 12 18 25 31 45 58 

180 12 18 25 32 45 59 

190 12 19 25 32 46 59 

200 12 19 26 32 46 60 

210 12 19 26 33 46 60 

220 12 19 26 33 47 61 

230 12 19 26 33 47 61 

240 12 19 26 33 47 61 

250 12 19 26 33 48 62 

260 12 19 27 34 48 62 

270 12 20 27 34 48 62 

280 12 20 27 34 48 63 

290 13 20 27 34 49 63 

300 13 20 27 34 49 53 

310 13 20 27 34 49 63 

20 Nov 2011 147






Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 12 15 21 27 762b/02 

40 8 10 14 17 25 32 

50 8 11 15 19 28 36 

60 8 12 17 21 30 39 

70 8 13 18 23 32 42 

80 8 14 19 24 34 44 

90 9 14 19 25 35 46 

100 9 15 20 26 37 47 

110 9 15 21 26 38 49 

120 10 15 21 27 39 50 

130 10 16 22 28 39 51 

140 10 16 22 28 40 52 

150 10 16 22 29 41 53 

160 10 17 23 29 41 54 

170 10 17 23 29 42 55 

180 11 17 23 30 42 55 

190 11 17 24 30 43 56 

200 11 17 24 30 43 56 

210 11 17 24 31 44 57 

220 11 18 24 31 44 57 

230 11 18 24 31 44 58 

240 11 18 25 31 45 58 

250 11 18 25 32 45 59 

260 11 18 25 32 45 59 

270 11 18 25 32 46 59 

280 11 18 25 32 46 60 

290 11 18 25 32 46 60 

300 12 18 25 32 46 60 

310 12 19 26 32 46 60 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 10 13 18 24 762b/02 

40 8 9 12 15 22 29 

50 8 10 14 17 25 32 

60 8 11 15 19 27 36 

70 8 11 16 20 29 38 

80 8 12 17 21 31 40 

148 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

90 8 13 18 23 32 42 

100 8 13 18 23 34 44 

110 8 14 19 24 35 45 

120 9 14 19 25 36 47 

130 9 14 20 25 37 48 

140 9 15 20 26 37 49 

150 9 15 21 26 38 50 

160 9 15 21 27 39 51 

170 9 15 21 27 39 51 

180 10 16 22 28 40 52 

190 10 16 22 28 40 53 

200 10 16 22 28 41 53 

210 10 16 22 29 41 54 

220 10 16 23 29 42 54 

230 10 16 23 29 42 55 

240 10 17 23 29 42 55 

250 10 17 23 30 43 56 

260 10 17 23 30 43 56 

270 10 17 23 30 43 56 

280 10 17 24 30 43 57 

290 10 17 24 30 44 57 

300 10 17 24 31 44 57 

310 11 17 24 31 44 58 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 9 11 16 21 762b/02 

40 8 8 10 13 20 26 

50 8 8 12 15 22 29 

60 8 9 13 17 24 32 

70 8 10 14 18 26 35 

80 8 11 15 19 28 37 

90 8 11 16 20 30 39 

100 8 12 16 21 31 40 

110 8 12 17 22 32 42 

120 8 12 18 23 33 43 

130 8 13 18 23 34 44 

140 8 13 18 24 35 45 

150 8 13 19 24 35 46 

160 8 14 19 25 36 47 

170 8 14 20 25 37 48 

180 8 14 20 26 37 49 

190 8 14 20 26 38 49 

200 9 14 20 26 38 50 

210 9 15 21 27 39 50 

220 9 15 21 27 39 51 

20 Nov 2011 149



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

230 9 15 21 27 39 52 

240 9 15 21 27 40 52 

250 9 15 21 28 40 52 

260 9 15 22 28 40 53 

270 9 15 22 28 41 53 

280 9 16 22 28 41 54 

290 9 16 22 28 41 54 

300 9 16 22 29 41 54 

310 9 16 22 29 42 55 

Cert. 

No. 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 8 11 15 20 762b/02 

40 8 8 10 13 19 24 

50 8 8 11 15 21 28 

60 8 9 12 16 23 31 

70 8 10 13 17 25 33 

80 8 10 14 19 27 35 

90 8 11 15 20 28 37 

100 8 11 16 20 30 39 

110 8 12 16 21 31 40 

120 8 12 17 22 32 42 

130 8 12 17 22 33 43 

140 8 13 18 23 33 44 

150 8 13 18 24 34 45 

160 8 13 19 24 35 46 

170 8 13 19 24 35 46 

180 8 14 19 25 36 47 

190 8 14 19 25 37 48 

200 8 14 20 25 37 49 

210 8 14 20 26 37 49 

220 8 14 20 26 38 50 

230 8 14 20 26 38 50 

240 8 15 21 27 39 51 

250 9 15 21 27 39 51 

260 9 15 21 27 39 51 

270 9 15 21 27 40 52 

280 9 15 21 27 40 52 

290 9 15 21 28 40 53 

300 9 15 21 28 40 53 

310 9 15 22 28 41 53 


150 20 Nov 2011





Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 9 10 14 19 762b/02 

40 8 8 9 12 17 23 

50 8 8 10 13 20 26 

60 8 8 11 15 22 29 

70 8 9 12 16 24 31 

80 8 9 13 17 25 33 

90 8 10 14 18 27 35 

100 8 10 15 19 28 37 

110 8 11 15 20 29 38 

120 8 11 16 20 30 39 

130 8 11 16 21 31 41 

140 8 12 17 22 32 42 

150 8 12 17 22 32 43 

160 8 12 17 23 33 43 

170 8 12 18 23 34 44 

180 8 13 18 23 34 45 

190 8 13 18 24 35 46 

200 8 13 18 24 35 46 

210 8 13 19 24 36 47 

220 8 13 19 25 36 47 

230 8 13 19 25 36 48 

240 8 13 19 25 37 48 

250 8 14 19 25 37 49 

260 8 14 20 26 37 49 

270 8 14 20 26 38 50 

280 8 14 20 26 38 50 

290 8 14 20 26 38 50 

300 8 14 20 26 39 51 

310 8 14 20 27 39 51 




Product 

Cert. 

Name 

No. 

Cafco 

Mandolite 

CP2 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

30 8 8 8 8 12 16 762b/02 

40 8 8 8 10 15 20 

50 8 8 9 12 17 23 

60 8 8 10 13 19 26 

70 8 8 11 14 21 28 

80 8 8 12 15 23 30 

90 8 8 12 16 24 32 

100 8 9 13 17 25 33 

110 8 9 13 18 26 35 

120 8 9 14 18 27 36 

20 Nov 2011 151



Product 

Name 

Section 

Factor 

(Hp/A) 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

30 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

60 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

90 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

120 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

180 min 

Applied 

Thickness 

(mm) of 

Cafco 

Mandolite 

CP2 for Fire 

Resistance 

Protection 

Periods of; 

240 min 

130 8 10 14 19 28 37 

140 8 10 15 19 29 38 

150 8 10 15 20 29 39 

160 8 10 15 20 30 40 

170 8 11 16 21 31 41 

180 8 11 16 21 31 41 

190 8 11 16 21 32 42 

200 8 11 16 22 32 43 

210 8 11 17 22 33 43 

220 8 12 17 22 33 44 

230 8 12 17 23 34 44 

240 8 12 17 23 34 45 

250 8 12 17 23 34 45 

260 8 12 18 23 35 46 

270 8 12 18 23 35 46 

280 8 12 18 24 35 47 

290 8 12 18 24 35 47 

300 8 12 18 24 36 47 

310 8 12 18 24 36 48 

Cert. 

No. 

Notes: 

1. LPCB Ref 726b/02 - profile application applied in several coats dependant on thickness. 

2. LPCB Ref 726b/02 - applied thicknesses quoted are without re-enforcement mesh included in coating. 

3. LPCB Ref 726b/02 - Cafco Mandolite CP2 approved from the following manufacturing site only; Promat UK Ltd, Lawn Road Industrial 

Estate, Carlton-in-Lindrick, Worksop, Notts S81 9LB UK. 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022d to LPS 1107: Issue 1 

Product Name Exposure Additional Information Cert. 

No. 

Rockwool FirePro(TM) 

BeamClad systems 

Internal and 

semi exposed 

Thickness range 25mm to 110mm. Fire resistance 30-240min (see tables 

below). Faced and unfaced boards are available, refer to manufacturer's 

technical literature for fixing details. 

022d/01 

3 Sided Protection of Steel Beams, Supporting Concrete/Composite Decks Using The Clip Fix Or Stud 

Welded Pins/Dry Joint System (critical failure temperature 620°C) 

Product Name Board Performance Performance Performance Performance Cert. No. 

Thickness 

(mm) 

Hp/A 30min Hp/A 60min Hp/A 90min Hp/A 120min 

BeamClad 25 260 260 260 95 022d/01 

30 260 260 260 124 

35 260 260 260 159 

40 260 260 260 200 

45 260 260 260 251 

50 260 260 260 260 

55 260 260 260 260 

60 260 260 260 260 

152 20 Nov 2011



3 Sided Protection Of Steel Beams, Supporting Concrete/Composite Decks Using The Bonded 

Noggin/Dry Joint System (critical failure temperature 620°C) 


Thickness 

(mm) 


BeamClad 25 260 260 196 73 022d/01 

30 260 260 260 93 

35 260 260 260 116 

40 260 260 260 143 

45 260 260 260 173 

50 260 260 260 209 

55 260 260 260 252 

60 260 260 260 260 

3 Sided Protection Of Steel Beams, Supporting Concrete/Composite Decks Using The Bonded Noggin 

Or Stud Welded Pins/Glued Joint System (critical failure temperature 620°C) 

Product 

Name 

Board 

Thickness 

Performance 

Hp/A 30min 

Performance 

Hp/A 60min 

Performance 

Hp/A 90min 

Performance 

Hp/A 120min 

Performance 

Hp/A 180min 

Performance 

Hp/A 240min 

Cert. 

No. 

(mm) 

BeamClad 25 260 260 260 168 52 - 022d/01 

30 260 260 260 235 65 - 

35 260 260 260 260 80 45 

40 260 260 260 260 95 53 

45 260 260 260 260 113 62 

50 260 260 260 260 132 70 

55 260 260 260 260 154 80 

60 260 260 260 260 178 90 

65 260 260 260 260 206 100 

70 260 260 260 260 237 112 

75 260 260 260 260 260 124 

80 260 260 260 260 260 136 

85 260 260 260 260 260 150 

90 260 260 260 260 260 165 

95 260 260 260 260 260 181 

100 260 260 260 260 260 199 

110 260 260 260 260 260 238 

4 Sided Protection Of Steel Beams And Columns Using The Clip Fix Or Stud Welded Pins/Dry Joint 

System (critical failure temperature 550°C) 


Thickness 

(mm) 


BeamClad 25 260 260 148 65 022d/01 

30 260 260 260 84 

35 260 260 260 104 

40 260 260 260 128 

45 260 260 260 155 

50 260 260 260 187 

55 260 260 260 225 

60 260 260 260 260 

4 Sided Protection Of Steel Beams And Columns Using The Bonded Noggin/Dry Joint System (critical 

failure temperature 550°C) 


Thickness 

(mm) 

Hp/A 

30min 

Hp/A 

60min 

Hp/A 

90min 

Hp/A 

120min 

BeamClad 25 260 260 146 65 022d/01 

30 260 260 202 83 

35 260 260 260 103 

40 260 260 260 126 

45 260 260 260 153 

50 260 260 260 184 

55 260 260 260 221 

20 Nov 2011 153



Product Name 

Board 

Thickness 

(mm) 

Performance 

Hp/A 

30min 

Performance 

Hp/A 

60min 

Performance 

Hp/A 

90min 

Performance 

Hp/A 

120min 

60 260 260 260 260 

Cert. No. 

4 Sided Protection Of Steel Columns Using The Bonded Noggin Or Stud Welded Pins/Glued Joint 


Product 

Name 

Board 

Thickness 

Performance 

Hp/A 

Performance 

Hp/A 

Performance 

Hp/A 

Performance 

Hp/A 

Performance 

Hp/A 

Performance 

Hp/A 

Cert. 

No. 

(mm) 30min 60min 90min 120min 180min 240min 

BeamClad 25 260 260 149 65 - - 022d/01 

30 260 260 207 83 - - 

35 260 260 260 104 45 - 

40 260 260 260 128 54 - 

45 260 260 260 155 62 - 

50 260 260 260 187 72 44 

55 260 260 260 225 82 50 

60 260 260 260 260 92 55 

65 260 260 260 260 104 61 

70 260 260 260 260 116 68 

75 260 260 260 260 129 74 

80 260 260 260 260 143 81 

85 260 260 260 260 159 88 

90 260 260 260 260 176 96 

95 260 260 260 260 194 103 

100 260 260 260 260 214 124 

110 260 260 260 260 260 129 

4 Sided Protection Of Steel Beams Using The Bonded Noggin Or Stud Welded Pins/Glued Joint 


Product 

Name 

Board 

Thickness 

(mm) 

Performance 

Hp/A 

30min 

Performance 

Hp/A 

60min 

Performance 

Hp/A 

90min 

Performance 

Hp/A 

120min 

Performance 

Hp/A 

180min 

Performance 

Hp/A 

240min 

BeamClad 25 260 260 260 98 40 - 022d/01 

30 260 260 260 130 50 - 

35 260 260 260 168 61 - 

40 260 260 260 216 73 43 

45 260 260 260 260 85 50 

50 260 260 260 260 99 57 

55 260 260 260 260 114 65 

65 260 260 260 260 131 73 

65 260 260 260 260 150 81 

70 260 260 260 260 170 90 

75 260 260 260 260 193 99 

80 260 260 260 260 219 109 

85 260 260 260 260 248 120 

90 260 260 260 260 260 131 

95 260 260 260 260 260 144 

100 260 260 260 260 260 157 

110 260 260 260 260 260 186 

Cert. 

No. 

154 20 Nov 2011


STRUCTURAL STEEL FIRE PROTECTION - INTUMESCENT THIN FILM COATINGS 

The protection of the structural integrity of a building is important for life safety of the occupants, fire fighters 

and for the cost-effective repair of the building post fire. When a building is involved in a fire, structural 

steelwork can resist the damaging effects of the high temperatures generated if suitably protected. 

This section covers structural steel fire protection with use of intumescent thin film coatings approved to 

SD075 Fire Protection for Structural Steelwork (Intumescent Systems) (BS 476: Parts 20 & 21). 

Promat UK Ltd 


Tel: +44 (0)1344 381 300 • Fax: +44 (0)1344 381 301 

Website: www.promat-spray.co.uk 

Certificate No: 762a to SD075 - BS 476: Parts 20 & 21 

Cafco Sprayfilm WB3 Intumescent Paint, 4 Sided Protection on Hollow Sections 532ºC 

Product 

Name 

SprayFilm 

WB3 

Section 

Factor 

(Hp/A) 

Intumescent Dry 

Film Thickness 

(mm) 

for Protection 

Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

Up to 45 0.61 0.61 1.80 3.51 762a/01 

45-50 0.61 0.61 1.80 3.51 

51-55 0.61 0.61 1.80 3.51 

56-60 0.61 0.61 1.80 3.51 

61-65 0.61 0.61 1.90 3.51 

66-70 0.61 0.61 2.00 3.51 

71-75 0.61 0.61 2.10 3.51 

76-80 0.61 0.61 2.19 3.51 

81-85 0.61 0.61 2.29 3.51 

86-90 0.61 0.61 2.39 3.51 

91-95 0.61 0.69 2.49 3.51 

96-100 0.61 0.78 2.55 3.59 

101-105 0.61 0.86 2.62 3.99 

106-110 0.61 0.94 2.67 4.39 

111-115 0.61 1.06 2.72 4.80 

116-120 0.61 1.08 2.77 5.20 

121-125 0.61 1.11 2.83 5.60 

126-130 0.61 1.14 2.88 6.00 

131-135 0.61 1.17 2.93 - 

136-140 0.61 1.20 2.98 - 

141-145 0.61 1.23 3.03 - 

146-150 0.61 1.26 3.08 - 

151-155 0.61 1.29 3.13 - 

156-160 0.61 1.32 3.18 - 

161-165 0.61 1.35 3.25 - 

166-170 0.61 1.38 3.29 - 

171-175 0.61 1.41 3.34 - 

176-180 0.61 1.45 3.39 - 

181-185 0.61 1.48 3.44 - 

186-190 0.61 1.51 3.51 - 

191-195 0.61 1.54 3.61 - 

196-200 0.61 1.57 3.77 - 

201-205 0.61 1.60 3.93 - 

206-210 0.61 1.63 4.08 - 

211-215 0.61 1.66 4.24 - 

216-220 0.61 1.69 4.40 - 

221-225 0.61 1.72 4.56 - 

226-230 0.61 1.75 4.72 - 

231-235 0.61 1.78 4.88 - 

236-240 0.61 1.83 5.04 - 

241-245 0.61 1.91 5.20 - 

246-250 0.61 1.99 5.36 - 

Cert. 

No. 

20 Nov 2011 155



Product 

Name 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

251-255 0.61 2.07 5.52 - 

256-260 0.61 2.15 5.68 - 

261-265 0.61 2.23 5.84 - 

266-270 0.61 2.31 6.00 - 

271-275 0.61 2.39 - - 

276-280 0.61 2.47 - - 

281-285 0.61 2.55 - - 

286-290 0.61 2.62 - - 

291-295 0.61 2.68 - - 

296-300 0.61 2.75 - - 

301-305 0.61 2.82 - - 

306-310 0.61 2.88 - - 

311-315 0.61 2.95 - - 

316-320 0.61 3.02 - - 

Cert. 

No. 

Notes: 

1. LPCB Ref 762a/01 - Intumescent dry film thickness excludes any primer or top coat film thickness. 

2. LPCB Ref 762a/01 - SprayFilm WB3 approved from the following manufacturing sites; Promat UK Ltd, Lawn Road Industrial Estate, 

Carlton-in-Lindrick, Worksop, Notts S81 9LB UK and Comais Srl, Via Provinciale, 10 - Filago (BG), 24040 Italy (FPC Ref. 935). 


Cafco Sprayfilm WB3 Intumescent Paint, 3 Sided Protection On I Section Beams (continuous concrete 

topping) 620ºC 

Product 

Cert. 

Name 

No. 

SprayFilm 

WB3 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

Up to 45 0.23 0.25 1.20 1.20 762a/01 

45-50 0.23 0.25 1.20 1.20 

51-55 0.23 0.25 1.20 1.20 

56-60 0.23 0.25 1.20 1.20 

61-65 0.23 0.25 1.20 1.20 

66-70 0.23 0.25 1.20 1.23 

71-75 0.23 0.25 1.20 1.28 

76-80 0.23 0.27 1.20 1.33 

81-85 0.23 0.28 1.20 1.39 

86-90 0.23 0.30 1.20 1.44 

91-95 0.23 0.32 1.20 1.49 

96-100 0.23 0.34 1.20 1.63 

101-105 0.23 0.36 1.20 1.78 

106-110 0.23 0.38 1.20 1.94 

111-115 0.23 0.40 1.20 2.04 

116-120 0.23 0.42 1.20 2.10 

121-125 0.23 0.44 1.22 2.17 

126-130 0.23 0.46 1.25 2.23 

131-135 0.23 0.48 1.28 2.30 

136-140 0.23 0.50 1.31 2.36 

141-145 0.23 0.52 1.34 2.43 

146-150 0.23 0.54 1.37 2.49 

151-155 0.23 0.56 1.40 2.56 

156-160 0.23 0.57 1.43 2.62 

161-165 0.23 0.57 1.46 2.69 

166-170 0.23 0.57 1.49 2.75 

171-175 0.23 0.61 1.54 2.82 

176-180 0.23 0.64 1.60 2.88 

181-185 0.23 0.67 1.66 2.95 

186-190 0.23 0.70 1.72 3.01 

191-195 0.23 0.73 1.78 3.18 

196-200 0.23 0.76 1.84 3.33 

201-205 0.23 0.80 1.90 3.48 

156 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

206-210 0.23 0.83 1.96 3.64 

211-215 0.24 0.86 2.02 3.79 

216-220 0.24 0.88 2.07 3.94 

221-225 0.24 0.89 2.12 4.21 

226-230 0.24 0.91 2.17 4.57 

231-235 0.24 0.93 2.22 4.93 

236-240 0.25 0.94 2.27 5.29 

241-245 0.25 0.96 2.32 5.64 

246-250 0.25 0.97 2.37 6.00 

251-255 0.25 0.99 2.42 - 

256-260 0.25 1.00 2.47 - 

261-265 0.26 1.02 2.52 - 

266-270 0.26 1.04 2.57 - 

271-275 0.27 1.05 2.62 - 

276-280 0.28 1.07 2.67 - 

281-285 0.28 1.08 2.72 - 

286-290 0.29 1.10 2.77 - 

291-295 0.29 1.11 2.82 - 

296-300 0.30 1.13 2.87 - 

301-305 0.30 1.14 2.92 - 

306-310 0.31 1.16 2.97 - 

311-315 0.31 1.18 3.02 - 

316-320 0.31 1.19 3.22 - 

Cert. 

No. 


Cafco Sprayfilm WB3 Intumescent Paint, 4 Sided Protection On I Section Beams 550ºC 

Product 

Name 

SprayFilm 

WB3 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

Up to 45 0.23 0.57 1.20 1.20 762a/01 

45-50 0.23 0.57 1.20 1.25 

51-55 0.23 0.57 1.20 1.31 

56-60 0.23 0.57 1.20 1.38 

61-65 0.23 0.57 1.20 1.46 

66-70 0.23 0.57 1.20 1.53 

71-75 0.23 0.57 1.20 1.75 

76-80 0.23 0.57 1.20 1.93 

81-85 0.23 0.57 1.20 2.05 

86-90 0.23 0.57 1.20 2.13 

91-95 0.23 0.57 1.20 2.21 

96-100 0.23 0.57 1.20 2.29 

101-105 0.23 0.57 1.25 2.37 

106-110 0.23 0.57 1.30 2.44 

111-115 0.23 0.57 1.35 2.52 

116-120 0.23 0.57 1.40 2.60 

121-125 0.23 0.57 1.45 2.68 

126-130 0.23 0.63 1.50 2.76 

131-135 0.23 0.68 1.60 2.84 

136-140 0.23 0.74 1.69 2.92 

141-145 0.23 0.79 1.79 3.00 

146-150 0.23 0.85 1.88 3.13 

151-155 0.23 0.88 1.98 3.25 

156-160 0.23 0.90 2.04 3.38 

161-165 0.23 0.92 2.08 3.50 

166-170 0.23 0.94 2.13 3.63 

171-175 0.24 0.96 2.18 3.75 

176-180 0.24 0.98 2.22 3.88 

181-185 0.24 1.00 2.27 4.00 

186-190 0.24 1.02 2.32 4.31 

191-195 0.24 1.04 2.36 4.63 

Cert. 

No. 

20 Nov 2011 157



Product 

Name 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

196-200 0.25 1.05 2.41 4.94 

201-205 0.25 1.07 2.46 5.25 

206-210 0.25 1.09 2.50 5.56 

211-215 0.25 1.11 2.55 5.88 

216-220 0.26 1.13 2.60 6.19 

221-225 0.27 1.15 2.64 - 

226-230 0.27 1.17 2.69 - 

231-235 0.28 1.19 2.74 - 

236-240 0.29 1.21 2.79 - 

241-245 0.30 1.23 2.83 - 

246-250 0.30 1.25 2.88 - 

251-255 0.31 1.27 2.93 - 

256-260 0.32 1.29 2.97 - 

261-265 0.32 1.31 3.02 - 

266-270 0.33 1.33 3.23 - 

271-275 0.34 1.35 3.39 - 

276-280 0.35 1.37 3.55 - 

281-285 0.35 1.39 3.71 - 

286-290 0.36 1.41 3.87 - 

291-295 0.37 1.43 4.03 - 

296-300 0.38 1.45 4.31 - 

301-305 0.38 1.47 4.56 - 

306-310 0.39 1.49 4.82 - 

311-315 0.40 1.51 5.08 - 

316-320 0.40 1.54 5.33 - 

Cert. 

No. 

Certificate No: 762a/01 to SD075 - BS 476: Parts 20 & 21 

Cafco Sprayfilm WB3 Intumescent Paint, 4 Sided Protection On I Section Columns 550ºC 

Product 

Name 

SprayFilm 

WB3 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

Up to 45 0.23 0.60 1.50 1.50 762a/01 

45-50 0.23 0.60 1.50 1.50 

51-55 0.23 0.60 1.50 1.50 

56-60 0.23 0.60 1.50 1.50 

61-65 0.23 0.60 1.50 1.50 

66-70 0.23 0.60 1.50 1.67 

71-75 0.23 0.60 1.50 1.83 

76-80 0.23 0.60 1.50 2.00 

81-85 0.23 0.60 1.50 2.08 

86-90 0.23 0.60 1.50 2.15 

91-95 0.23 0.60 1.50 2.23 

96-100 0.23 0.60 1.50 2.31 

101-105 0.23 0.60 1.50 2.38 

106-110 0.23 0.60 1.50 2.46 

111-115 0.23 0.60 1.50 2.54 

116-120 0.23 0.60 1.50 2.62 

121-125 0.23 0.66 1.57 2.69 

126-130 0.23 0.71 1.62 2.77 

131-135 0.23 0.75 1.67 2.85 

136-140 0.23 0.80 1.72 2.92 

141-145 0.23 0.85 1.78 3.00 

146-150 0.23 0.87 1.83 3.11 

151-155 0.23 0.88 1.88 3.23 

156-160 0.24 0.89 1.93 3.34 

161-165 0.24 0.90 1.98 3.45 

166-170 0.24 0.90 2.03 3.57 

171-175 0.24 0.91 2.08 3.68 

176-180 0.24 0.92 2.14 3.80 

181-185 0.25 0.92 2.19 3.91 

Cert. 

No. 

158 20 Nov 2011



Product 

Name 

Section 

Factor 

(Hp/A) 



(mm) 


Periods of: 

30 min 



(mm) 


Periods of: 

60 min 



(mm) 


Periods of: 

90 min 



(mm) 


Periods of: 

120 min 

186-190 0.25 0.93 2.24 4.02 

191-195 0.25 0.94 2.29 4.43 

196-200 0.25 0.95 2.34 4.79 

201-205 0.25 0.95 2.40 5.14 

206-210 0.26 0.96 2.45 5.50 

211-215 0.26 0.97 2.50 5.86 

216-220 0.27 0.97 2.55 6.21 

221-225 0.27 0.98 2.60 - 

226-230 0.28 0.99 2.66 - 

231-235 0.28 1.00 2.71 - 

236-240 0.29 1.00 2.76 - 

241-245 0.29 1.04 2.81 - 

246-250 0.30 1.06 2.86 - 

251-255 0.30 1.09 2.92 - 

256-260 0.31 1.12 2.97 - 

261-265 0.31 1.14 3.02 - 

266-270 0.32 1.17 3.14 - 

271-275 0.32 1.19 3.24 - 

276-280 0.33 1.22 3.34 - 

281-285 0.33 1.25 3.44 - 

286-290 0.34 1.27 3.54 - 

291-295 0.34 1.30 3.64 - 

296-300 0.35 1.33 3.74 - 

301-305 0.35 1.35 3.84 - 

306-310 0.36 1.38 3.94 - 

311-315 0.36 1.41 4.04 - 

316-320 0.37 1.43 4.32 - 

Cert. 

No. 

Note: Intumescent dry film thickness exclude any primer or top coat film thickness. 

20 Nov 2011 159


PROTECTIVE COVERING MATERIALS & SCAFFOLD CLADDING 

This section includes LPS 1207 Fire requirements for protective covering materials which are used during the 

construction of new buildings and renovation of existing buildings, and LPS 1215 Requirements for the LPCB 

Approval and Listing of Scaffold cladding materials. 

160 20 Nov 2011


LPS 1207 PROTECTIVE COVERING MATERIALS 

During the construction of new buildings and renovation of existing buildings, it is common to use sheeting 

made from plastic or similar materials to provide protection against the weather, dust and other materials 

produced by work in adjacent areas. If a material complies with LPS 1207 Fire requirements for protective 

covering materials it will not add significantly to the fire risk. This standard is referred to in The Joint Code of 

Practice on the Protection from Fire of Construction Sites & Buildings Undergoing Renovation, 7th Edition 

published by the FPA in association with RISC Authority 

20 Nov 2011 161


LPS 1207 PROTECTIVE COVERING MATERIALS - SHEETING 

Bainbridge International Limited 

Unit 8, Flanders Park, Flanders Road, Hedge End, Southampton, Hampshire SO30 2FZ, United Kingdom 

Tel: 01489 776050 • Fax: 01489 776055 

E-mail: info@coverguard.com • Website: www.coverguard.com 

Certificate No: 1058a to LPS 1207 Issue 2 

Product Name Thickness (mm) Weight (g/m²) Cert. No. 

Wall cover guard (CG0636TF & CG06272TF) 0.15 ± 15% 150 ± 10% 1058a/01 

Floor cover guard (CG1036DP-CG4036DP) 0.25 - 1.0 ± 15% 250 - 1000 ± 10% 1058a/02 

Scaffold cover guard (CG0872SC) 0.2 ± 15% 286 ± 10% 1058a/03 

Notes: 

1. LPCB Ref 1058a/01 & 1058a/02 Wall and Floor cover guard is available in blue only and covers non printed material with a printed 

product marking bands as required by LPS1207 Issue 2 Clause 4 only. 

2. LPCB Ref 1058a/03 Scaffold cover guard is available in white only and covers non printed material with a printed product marking 

band as required by LPS1207 Issue 2 Clause 4 only. 

BPI Visqueen - Greenock 

96 Port Glasgow Road, Greenock, Scotland PA15 2UL, United Kingdom 

Tel: +44 (0)1475 501100 • Fax: +44 (0)1475 743256 

Website: www.bpipoly.com 


Product Name 

Thickness Weight Cert. No. 

(mm) (g/m 2 ) 

Megafilm Flame Retardant Polythene Protection Films (Visqueen Megafilm) 0.065 to 0.5 - 521a/01 

Visqueen Flame Retardant Polythene Protection Films (Portathene WRE50) 0.03 to 0.5 - 521a/02 

Note: 

1. LPCB Ref. No. 521a/01 - Megafilm products can be supplied in various flat and textured profiles, and is available in a variety of 

colours. 

Certificate No: 688a-x4 to LPS1207: Issue 2 

Product Name Thickness (mm) Weight (g/m2) Cert. No. 

Megaboard Twinwall Polyrpopylene 2.0 - 4.5mm 250 - 1000 688a-x4/01 

Megaboard Recycled FR 2.0 250 688a-x4/02 

Notes: 

1. LPCB Ref No. 688a-x4/01 is available in white only and covers printed and non printed material with a product marking band as 

required by LPS 1207: Issue 2 Clause 4. 

2. LPCB Ref.No. 688a-x4/02 is available in black only and covers non printed material with a printed product marking band as required 

by LPS 1207: Issue 2 Clause 4 only. 

Britton Merlin Limited 

Brackenborough Road, Louth, Lincolnshire LN11 0AX, United Kingdom 

Tel: +44 (0)1507 617800 • Fax: +44 (0)1507 601681 

E-mail: tuffreel@britton-group.com 


162 20 Nov 2011



Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Tuffreel Flame Retardant (G6) 0.038 - 0.25 ± 20% 38 - 250 ± 10% 499a/01 

BS2. Merlin 0.04 ± 20% 40 ± 10% 499a/02 

Notes: 

1. LPCB Ref No. 499/01 covers non-printed material with a printed product marking band as required by LPS 1207: issue 2 Clause 4 

only. 

2. LPCB Ref. No. 499a/02 covers printed and non-printed material as sepcified with printed product marking band as required by LPS 

1207: Issue 2 Clause 4. 

Core Industrial Plastics Limited 

Unit 12, A1 Ferrybridge Business Park, Fishergate, Knottingley, West Yorkshire WF11 8NA, United Kingdom 

Tel: +44 (0)1977 676072 • Fax: +44 (0)1977 676069 

E-mail: sales@coreplastics.co.uk 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 

Total Protection Board (Black) 2.3 ± 0.5 200 - 800 803a/02 

Total Protection Board (White) 2.3 ± 0.5 200 - 800 803a/03 

Note: 

1. LPCB Ref. No. 803a/02 & 803a/03 covers printed and non printed materials with a printed product marking band as required by LPS 

1207 Issue 2 clause 4. 

Don & Low Ltd, Nonwovens 

Glamis Road, Forfar, Angus DD8 1EY, United Kingdom 

Tel: +44 (0)1307 452600 • Fax: +44 (0)1307 452635 

E-mail: nonwovens@donlow.co.uk • Website: www.donlow.com 


Product Name 


(mm) 

(g/m 2 ) 

Daltex Flame Retardant Spunbond (A100E5TFR) 0.5 nominal 100 ±6% 726a/01 

DS SMITH CORREX (Trading as a division of DS Smith Plastics Limited) 

Madleaze Industrial Estate, Bristol Road, Gloucester GL1 5SG, United Kingdom 

Tel: +44 (0)1452 316500 • Fax: +44 (0)1452 300436 

E-mail: sales@kayplast.com • Website: www.kaysersberg-plastics.com 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Correx Twinwall (black) 2.0 to 6.0 250 to 1500 227a/01 

Correx Twinwall (coloured & translucent) 2.0 to 6.0 250 to 1500 227a/02 

20 Nov 2011 163



Envirowrap Solutions Limited 

Registered Office:, Strangford House, Church Road, Ashford, Kent TN23 3QR, United Kingdom 

Tel: +44 (0)1233 860080 • Fax: +44 (0)1233 860090 

E-mail: enquiries@envirowrap.info • Website: www.envirowrap.info 


Envirowrap 250, 300, 350 & 400AFR-T D06-08 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Envirowrap 250AFR-T D06-08 0.25 ± 5% 253 ± 5% 691a/02 

Envirowrap 300AFR-T D06-08 0.30 ± 5% 305 ± 5% 



Note: 

1. LPCB Ref No. 691a/02 is available in white/light cream only and covers non printed product material with a printed product marking 

band as required by LPS 1207 Issue 2 Clause 4. 

Florprotec Limited 

Relay Park, Relay Drive, Tamworth B77 5PR, United Kingdom 

Tel: +44 (0)1827 831440 • Fax: +44 (0)1827 831441 

E-mail: sales@florprotec.co.uk • Website: www.floorprotection.co.uk 

Certificate No: 688a-x1 to LPS 1207: Issue 2.1 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 

Florprotec T-Bord 2.0 - 4.5 250 - 1000 688a-x1/01 

Florprotec Envirobord 2.0 250 688a-x1/02 

Notes: 



2. LPCB Ref No. 688a-x1/02 is availabe in black only and covers non printed material with a printed product marking band as required 

by LPS1207: Issue 2 Clause 4 only. 

Certificate No: 871a to LPS1207: Issue 2.1 

Product Name Thickness Weight 

Cert. No. 

(g/m²) 

CPP-FR 0.16 ± 10% 84 ± 5% 871a/01 

Notes 

1. LPCB Ref. No. 871a/01 covers white base sheet material, with or without additional printed areas, with a printed product marking band 

as required by LPS 1207 Issue 2 clause 4. 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

TACBAC FR 0.065 nominal 83 ± 10% 1030a/01 

Notes 

1. LPCB Ref. No. 1030a/01 covers white (natural) base film material, printed and non-printed material with a printed product marking 

band as required by LPS 1207: Issue 2 Clause 4. 

2. LPCB ref. No. 1030a/01 TACBAC FR is a self-adhesive film. 

3. LPCB ref. No. 1030a/01 TACBAC FR the thickness quoted is the nominal film thickness and weight is quoted inclusive of the 

adhesive. 

164 20 Nov 2011



Gilray Plant Limited 

Cedar Depot, Church Manorway, Erith, Kent DA8 1DE, United Kingdom 

Tel: 01322 442006 • Fax: 01322 442009 

E-mail: sarah.wilson@gilray.co.uk • Website: www.gilray.co.uk 

Certificate No: 915a-x2 to LPS 1207 Issue 2.1 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 

Fire-Retardant Multisheet 220 FR 0.7 ± 5% 220 +7/ - 5% 915a-x2/01 

Fire-Retardant Multisheet 170 FR 0.7 ± 5% 170 ± 10% 915a-x2/02 

Note: 

1. LPCB Ref No. 915a-x2/01 and 915a-x2/02 are available in white only and covers non printed material with a printed product marking 

band as required by LPS 1207 Issue 2 Clause 4 only. 

Goran Plastics 

Unit C, 5 Caxton Way, Watford Business Park, Watford, Herts WD18 8UA, United Kingdom 

Tel: +44 (0)1923 255700 • Fax: +44 (0)1923 255698 

E-mail: sales@goran.co.uk 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Polyflute Twinwall Polypropylene 2.0 - 4.5 250 - 1000 688a/01 

Polyflute Recycled FR 2.0 250 688a/02 

Notes: 

1. LPCB Ref No. 688a/01 is available in white only and covers printed and non printed material with a product marking band as required 

by LPS 1207: Issue 2 Clause 4. 

2. LPCB Ref. No. 688a/02 is available in black only and covers non printed material with a printed product making band as required by 

LPS 1207: Issue 2 Clause 4 only. 



Tel: +44 (0)161 865 4444 • Fax: +44 (0)161 865 8433 


Certificate No: 572c to LPS 1207: Issue 2 

Product Name Thickness (mm) Weight (g/m 2 ) Cert. No. 

Monarflex Stripe Firesmart 0.15 Nominal 210 ± 5% 540c/01 

Monarflex Super T Plus Firesmart 0.2 to 0.55 275 ± 5% 572c/01 

Notes: 

1. LPCB Ref. No. 572c/01 Monarflex Super T Plus Firesmart roll size 2.25m x 40m, 2m x 45m, 3m x 45m and 4m x 36m. Product 

produced at Monarflex s.r.o 

2. LPCB Ref. No. 572c/01 covers printed and non printed materials with a printed product marking band as required by LPS1207: Issue 

2 Clause 4. 

3. LPCB Ref. No. 540c/01 is available in white only and covers non printed materials with a printed product marking band as required by 

LPS1207: Issue 2 Clause 4 only. 

20 Nov 2011 165



Industrial Textiles & Plastics Ltd 

Stillington Road, Easingwold, York YO61 3FA, United Kingdom 

Tel: +44 (0)1347 825200 • Fax: +44 (0)1347 825222 

E-mail: info@itpltd.com • Website: www.itpltd.com 


Powerclad 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Powerclad SDFR 0.40 1 200 ±5% 727a/01 

Powerclad PMFR 0.40 1 240 ±5% 727a/02 

Notes: 

1) LPCB ref No. 727a/01 & 727a/02, the material thickness includes the reinforcing mesh. 

2) LPCB Ref. No’s. 727a/01 and 727a/02 covers printed and non printed Powerclad SDFR and PMFR materials with a printed product 

marking band as required by LPS 1207: Issue 2 Clause 4. 

Certificate No: 965a to LPS 1207 Issue 2.1 


Powerclad PMFR 0.50 ±7% 230 ±7% 965a/01 

Notes: 

1. LPCB Ref. No. 965a/01 the material thickness includes the reinforcing mesh 

2. LPCB Ref. No. 965a/01 covers non printed material with a printed product marking band as required by LPS 1207: Issue 2 Clause 4. 

IPB N.V. 

Steenovenstraat 30, B-8790 Waregem, Belgium 

Tel: UK Sales +44 (0)800 834704 • Fax: +44 (0)800 834705 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Proplex 2.0 to 4.0 250 to 1000 365a/01 

Landskroon B.V. 

Tweelingenlaan 43, 7324 AP Apeldoorn, PO Box 195, 7300 AD Apeldoorn, The Netherlands 

Tel: +31(0) 555 999 555 • Fax: +31(0) 555 340 200 

E-mail: office@landskroon.nl • Website: www.landskroon.nl 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Lankotex Scaffold TARP 220FR 0.7 ± 5% 220 +7/ - 5% 915a/01 

Lankotex Scaffold TARP 170FR 0.7 ± 5% 170 ± 10% 915a/02 

Note: 

1. LPCB Ref No. 915a/01 and 915a/02 are available in white only and cover non printed material with a printed product marking band as 

required by LPS 1207 Issue 2 Clause 4 only. 

166 20 Nov 2011



Monarflex 

Lyskaer 10,, DK-2730 Herlev, Copenhagen, Denmark 

Tel: +45 44 88 55 50 • Fax: +45 44 88 55 99 

E-mail: contact@monarflex.com • Website: www.special-fire.com 


Product Name 

Weight 

Cert. No. 

(g/m 2 ) 

HD Barrier Film 206 to 252 540a/01 

MD Barrier Film 119 to 132 

Nields Plastic Company Limited 

Units 1 -2, Foley Works Estate, Hereford HR1 2SF, United Kingdom 

Tel: +44 (0)1432 268341 • Fax: +44 (0)1432 353247 

E-mail: sales@nields.co.uk 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Antimar 0.05 to 0.3 47 to 280±15% 342a/01 

Northern Ireland Plastics Limited 

39 Shrigley Road, Killyleagh, Co. Down, Northern Ireland BT30 9SR, United Kingdom 

Tel: +44 (0)2844 828753/4 • Fax: +44 (0)2844 828809 

E-mail: info@niplastics.co.uk 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Corriboard Twin Wall (white) 2.3 ± 0.5 200 to 800 341a/01 

Corriboard Twin Wall (black) 2.3 ± 0.5 200 to 800 341a/02 

Note: 

1. LPCB Ref. No. 341a/01 & 341a/02 covers printed and non printed materials with a printed product marking band as required by LPS 

1207 Issue 2 clause 4. 

Ockwells Limited 

Unit 6, Transigo, Gables Way, Thatcham, Berkshire RG19 4ZA, United Kingdom 

Tel: +44 (0)1635 876336 • Fax: +44 (0)1635 876338 

E-mail: sales@ockwell.co.uk • Website: www.ockwells.co.uk 

Certificate No: 726a-x1 to LPS 1207: Issue 2 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Floorshield FR 0.5 nominal 100 ±6% 726a-x1/01 

20 Nov 2011 167




Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Ockwells Twinshield (White) 2.3 ± 0.5 200 - 800 341a-x1/01 

Ockwells Twinshield (Black) 2.3 ± 0.5 200 - 800 341a-x1/02 

Note: 

1. LPCB Ref. No. 341a-x1/01 & 341a-x1/02 covers printed and non printed materials with a printed product marking band as required by 

LPS 1207 Issue 2 clause 4. 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Ockwells Twinshield (Natural colour) 2.0 to 10.0 270 to 2000 ± 10% 742a-x1/01 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Ockwells Twinshield 2.0 - 4.5 250 - 1000 688a-x2/01 

Note: 



Ondaplast SpA 

Via Crocetta, 3310, 47020 Longiano (FC), Italy 

Tel: +39 0547 56616 • Fax: +39 0547 54087 

E-mail: info@ondaplast.com • Website: www.ondaplast.com 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

RE-FLAM twin wall flame retardant sheet, natural colour 2.0 to 10.0 270 to 2000 ± 10% 742a/01 

Protec International Limited 

Construction House, Adlington Industrial Estate, Adlington, Cheshire SK10 4NL, United Kingdom 

Tel: +44 (0)1625 855666 • Fax: +44 (0)1625 855601 

E-mail: enquiries@protection.co.uk • Website: www.protection.co.uk 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 

Proplex 2.0 to 4.0 250 to 1000 365a/01 

Promesh 1207 0.12 to 0.43 85 to 210 ± 5% 495a/01 

Protec Flame Retardant Barrier Sheet 0.45 170 495a/03 

CushionGard FR 4.0 nominal 155 ± 10% 843a/01 

Breathershield FR 0.5 nominal 100 ± 6% 843a/02 

FR Carpet Shield 0.065 ± 7% 80 ± 10% 894a/01 

FR Polythene - White 0.05 to 0.25 ± 5% 50.2 to 247.25 ± 5% 894a/02 

168 20 Nov 2011



Notes: 

1. LPCB Ref. No. 495a/03, the material thickness of the Protec Flame retardant barrier sheet includes the textured profile. 

2. LPCB Ref. No. 495a/02, 843a/01 & 894/01 covers printed and non-printed material with a printed product marking band as required 

by LPS 1207: Issue 2 Clause 4. 

3. LPCB Ref. No. 495a/01, 495a/03 & 894a/02 covers non printed material with a printed product marking band as required by LPS 

1207 Issue 2 Clause 4 only. 

4. LPCB Ref. No. 894a/01, the thickness quoted is the material thickness pre-embossed. 

5. LPCB Ref. No. 849a/01, the approval products are self-adhesive films. 

Protecta Screen Ltd 

5 Driberg Way, Braintree, Essex CM17 1NB, United Kingdom 

Tel: +44 (0)870 1218670 • Fax: +44 (0)870 1218680 

E-mail: sales@protectascreen.com • Website: www.protectascreen.com 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Protectaboard 2.0 - 3.0 270 - 450 688a-x3/01 

Sealed Air Limited 

Telford Way, Kettering, Northants NN16 8UN, United Kingdom 

Tel: +44 (0)1886 884 747 • Fax: +44 (0)1886 884 125 

E-mail: enquiries@special-fire.com • Website: www.special-fire.com 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Cushion Wrap 1207 approx 4.2 118 ± 2 505a/01 

Note: 

LPCB Ref No. 505a/01 covers printed and non-printed material with a printed product marking band as required by LPS 1207: Issue 2 

Clause 4. 

Sealed Air Limited 

Telford Way, Kettering, Northants NN16 8UN, United Kingdom 

Tel: 01536 315 700 • Fax: 01536 315 702 

E-mail: kettering.orders@sealedair.com • Website: www.sealedair.com 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

g/m 2 ) 

CMFR approx.4.2 60 ± 2 505b/02 

Note: 

1. LPCB Ref. No. 505b/02 is available in white only and covers non printed material with a printed product marking band as required by 


20 Nov 2011 169



Solicom SA 

Rue de Drinklange 9, L-9911 Troisvierges, Luxembourg 

Tel: +352 26957256 • Fax: +352 26958056 

E-mail: info@solicompack.com • Website: www.verisafe.be 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Verisafe 200 (White) 0.20 ±5% 200 ±5% 789a/01 

Verisafe 400 (White) 0.40 ±5% 400 ±5% 789a/02 

Verisafe B1 280 (White) 0.28 +5/-10% 280 +5/-7% 789a/03 

Note: 

1. LPCB Ref. No. 789a/01, 789a/02 & 789a/03 are available in white only and cover non-printed Verisafe material as specified with a 

printed product marking band as required by LPS 1207: Issue 2 Clause 4 only. 

Sunjüt A.S. 

Yukari Dudullu, Organize San, Bölgesi I Cad. No. 29, Umraniye 34775, Istanbul, Turkey 

Tel: +44 (0)800 834704 • Fax: +44 (0)800 834705 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Promesh 1207 0.12 to 0.43 85 to 210 ± 5% 495a/01 

Protec Flame Retardant Barrier Sheet 0.45 170 495a/03 

Notes: 

1. LPCB Ref. No. 495a/03 The material thickness of the Protec flame retardant Barrier sheet includes the textured profile. 

2. LPCB Ref. No. 495a/01 & LPCB Ref. No. 495a/03 covers non printed material with a printed product marking band as required by 


The Blinking Lamp Company Ltd 

Unit F, Motorway Distribution Centre, Avonmouth Way, Bristol BS11 9YT, United Kingdom 

Tel: +44(0) 1179 828180 • Fax: +44(0) 1179 382818 

E-mail: office@blinkinglamp.co.uk • Website: www.blinkinglamp.co.uk 

Certificate No: 915a-x1 to LPS 1207 : Issue 2 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Tri-Flex HD FR 0.7 ± 5% 220 +7 / - 5% 915a-x1/01 

Tri-Flex FR 0.7 ± 5% 170 ± 10% 915a-x1/02 

Note: 

1. LPCB Ref No. 915a-x1/01 and 915a-x1/02 are available in white only and covers non printed material with a printed product marking 

band as required by LPS 1207 Issue 2 Clause 4 only. 

170 20 Nov 2011



Total Polyfilm Limited 

Armytage Road, The Industrial Estate, Brighouse, West Yorkshire HD6 1PT, United Kingdom 

Tel: +44 (0)1484 714313 • Fax: +44 (0)1484 720452 


Frapol Sheeting 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Frapol HD 0.200 to 0.300 ± 10% 186 to 279 ± 10% 527a/01 

Frapol LD 0.50 to 0.99 ± 10% 46 to 92 ± 10% 

Frapol MD 0.100 to 0.199 ± 10% 93 to 185 ± 10% 

Note: 

1. LPCB Ref No 527a/01 covers printed and non printed materials with a printed product marking band as required by LPS1207: Issue 2 

Clause 4. The approval covers natural (white) and pigmented film. 

Twinplast Limited 

Unit 2, Greycaine Road, Watford, Hertfordshire WD24 7GP, United Kingdom 

Tel: +44 (0)1923 230191/817761 • Fax: +44 (0)1923 817756 

E-mail: sales@twinplast.co.uk • Website: www.twinplast.co.uk 


Product Name 


(mm) 

(g/m 2 ) 

Twinplast / Antinox FR Protection Board (white) 2.0 to 6.0 250 to 1400 375a/01 

2.0 200 to 250 375a/02 

Twinplast / Antinox FR Protection Board (white, black or coloured) 2.0 to 4.0 250 to 1000 375a/03 

Twinplast / Antinox Antistatic FR Protection Board (white) 4.0 700 375a/04 

Twinplast / Antinox Recycled FR Protection Board (black) 2.0 250 375a/05 

Note: 

1. LPCB Ref Nos. 375a/01, 375a/02, 375a/03, 375a/04 and 375a/05 covers printed and non printed materials with a printed product 

marking band as required by LPS1207: Issue 2 Clause 4. 

Univar Speciality Consumables 

Armstrong Road, The Royal Arsenal, London SE18 6RS, United Kingdom 

Tel: +44 (0)20 8312 7200 • Fax: +44 (0)20 8312 7250 

E-mail: uscmsales@univareurope.com • Website: www.univareurope.com 


Product Name Thickness (mm) Weight (g/m 2 ) Cert. No. 

MP70TRA twin wall fluted sheet 2.0 250 ± 10 709a/01 

MP70BLA twin wall fluted sheet 2.0 250 ± 10 709a/02 

MP70WHI twin wall fluted sheet 2.0 250 ± 10 709a/03 

Note: 

1. LPCB Ref. No. 709a/01, 709a/02 & 709a/03 covers printed and non printed materials with a printed product marking band as required 

by LPS1207: Issue 2 Clause 4. 

20 Nov 2011 171


LPS 1207 PROTECTIVE COVERING MATERIALS - PRE-FORMED 

Ockwells Limited 

Unit 6, Transigo, Gables Way, Thatcham, Berkshire RG19 4ZA, United Kingdom 

Tel: +44 (0)1635 876336 • Fax: +44 (0)1635 876338 

E-mail: sales@ockwell.co.uk • Website: www.ockwells.co.uk 

Certificate No: 898a to LPS1207: Issue 2 

Product Name 

Wall 

Thickness 

(mm) 

Size Range 

(mm) 

Density 

(g/m³) 

Cert. No. 

Ockwells 048 Universal Foam Protector - Flame Retardant 13 ± 1 O-Profile 48 36 ± 3 898a/01 

Ockwells114 Universal Foam Protector - Flame Retardant 13 ±1 O-Profile 114 36 ± 3 

Ockwells 90/110 Universal Foam Protector - Flame Retardant 13 ± 1 U-Profile 90/110 36 ± 3 898a/02 

Note: 

1. LPCB Ref. No. 898a/01 & 898a/02 is available in Orange only and covers non printed material with a printed product marking band as 

required by LPS 1207: Issue 2 Clause 4 only. 



Tel: +44 (0)1625 855666 • Fax: +44 (0)1625 855601 



Product Name 

Wall Thickness 

Size Range 

Density 3 ) Cert. No. 

(mm) 

(mm) 

Protective Foam Tubing (Red) 13 -1/+0.5 Internal dia. 15 to 114 30±5 634a/01 

172 20 Nov 2011


LPS 1215 SCAFFOLD CLADDING MATERIALS 

Scaffold cladding materials such as sheeting and netting are often used externally during construction, 

refurbishment or demolition of buildings to provide protection. Historically, there have been a number of 

significant losses associated with fires involving scaffolding. Scaffold cladding materials should not add to the 

fire risk if they comply with LPS 1215 Requirements for the LPCB approval and listing of scaffold cladding 

materials. 

Note: LPS 1215:Issue 3 does not cover other features required of scaffold materials, such as resistance to 

wind, rain penetration, resistance to tearing or impact damage. 



Tel: +44 (0)1233 860080 • Fax: +44 (0)1233 860090 



Envirowrap 250, 300, 350 & 400AFR-T D06-08 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Envirowrap 250AFR-T D06-08 0.25 ± 5% 253 ± 5% 691b/02 




Note: 

1. LPCB Ref No. 691b/02 is available in white/light cream only and covers non printed product material with a printed product marking 

band as required by LPS 1215 Issue 3 Clause 4. 

Gilray Plant Limited 

Cedar Depot, Church Manorway, Erith, Kent DA8 1DE, United Kingdom 

Tel: 01322 442006 • Fax: 01322 442009 

E-mail: sarah.wilson@gilray.co.uk • Website: www.gilray.co.uk 

Certificate No: 915b-x2 to LPS 1215 Issue 3 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Fire-Retardant Multisheet 220 FR 0.7 ± 5% 220 +7/ - 5% 915b-x2/01 

Fire-Retardant Multisheet 170 FR 0.7 ± 5% 170 ± 10% 

225 ± 10% (incl. printing) 

915b-x2/02 

Notes: 

1. LPCB Ref No. 915b-x2/01 is available in white only and covers non printed material with a printed product marking band as required 

by LPS 1215 Issue 3 Clause 4 only. 

2. LPCB Ref No. 915b-x2/02 is available in white only and covers printed and non printed material with a printed product marking band 

as required by LPS 1215 Issue 3 Clause 4. 


Flame Retardant Debris Netting 

Product Name Thickness (mm Weight (g/m²) Cert. No. 

Flame Retardant Debris Netting 0.75 ± 10% 85 ± 15% 1061a-x2/01 

Notes: 

1. LPCB Ref No. 1061a-x2/01 is available in Blue, White, Black, Green, Red, Yellow and Orange and is non-printed material as 

specified with a printed product marking band as required by LPS1215 Issue 3 clause 4 only. 

20 Nov 2011 173





Tel: +44 (0)161 865 4444 • Fax: +44 (0)161 865 8433 



Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Monarflex Stripe Firesmart 0.15 Nominal 210 ± 5% 540d/01 

Monarflex Super T Plus Firesmart 0.2 to 0.55 275 ± 5% 572d/01 

Monarflex Temporary Roof Cover Flamesafe 0.2 to 0.55 233 ± 10% 572d/02 

Notes: 

1. LPCB Ref. No. 572d/01 & 572d/02 Monarflex Super T Plus Firesmart roll size 2.25m x 40m, 2m x 45m, 3m x 45m and 4m x 36m. 

Monarflex Temporary Roof Cover Flamesafe roll size 23.35m x 50m and 3.35m x 30m. Products produced at Monarflex s.r.o 

2. LPCB Ref. No. 572d/01 covers printed and non printed materials with a printed product marking band as required by LPS1215: Issue 

3 Clause 4. 

3. LPCB Ref. No. 540d/01 is available in white only and covers non printed materials with a printed product marking band as required by 

LPS1215: Issue 3 Clause 4 only. 



Tel: +44 (0)1347 825200 • Fax: +44 (0)1347 825222 

E-mail: info@itpltd.com • Website: www.powerclad.com 


Powerclad 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Powerclad SDFR 0.40 200 ±5% 727b/01 

Powerclad PMFR 0.40 240 ±5% 727b/02 

Notes: 

1. LPCB Ref. No. 727b/01 & 727b/02, the material thickness includes the reinforcing mesh. 

2. LPCB Ref. No. 727b/01 and 727b/02 covers printed and non printed Powerclad SDFR and PMFR material with a printed product 

marking band as required by LPS 1215: Issue 3 Clause 4. 

Certificate No: 965b to LPS1215 Issue 3.1 


Powerclad PMFR 0.50 ±7% 230 ±7% 965b/01 

Powerclad SDFR 0.20 ±5% 180 ±9% 965b/02 

Powerclad RSFR 0.40 ±10% 300 ±10% 965b/03 

Notes: 

1. LPCB Ref No. 965b/01 the material thickness includes the reinforcing mesh. 

2. LPCB Ref. No. 965b/01 covers printed and non printed material with a printed product marking band as required by LPS 1215: Issue 

3 Clause 4. 

3. LPCB Ref. No. 965b/02 & 965b/03 covers non printed material with a printed product marking band as required by LPS 1215: Issue 3 

Clause 4. 

174 20 Nov 2011



Landskroon B.V. 

Tweelingenlaan 43, 7324 AP Apeldoorn, PO Box 195, 7300 AD Apeldoorn, The Netherlands 

Tel: +31(0) 555 999 555 • Fax: +31(0) 555 340 200 

E-mail: office@landskroon.nl • Website: www.landskroon.nl 

Certificate No: 915b to LPS1215: Issue 3 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Lankotex Scaffold TARP 220FR 0.7 ± 5% 220 +7 /- 5% 915b/01 

Lankotex Scaffold TARP 170FR 0.7 ± 5% 170 ± 10% 


915b/02 

Notes: 

1. LPCB Ref No. 915b/01 is available in white only and covers non printed material with a printed product marking band as required by 

LPS 1215 Issue 3 Clause 4 only. 

2. LPCB Ref No. 915b/02 is available in white only and covers printed and non printed material with a printed product marking band as 

required by LPS 1215 Issue 3 Clause 4. 



Tel: +44 (0)1625 855666 • Fax: +44 (0)1625 855601 



Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 

Proscaff Premium FR 0.60 250 495b/01 

Scaffnet FR (white) 0.30 (single yarn) 65±5% 495b/02 

Notes: 

1. LPCB Ref. 495b/01 Covers printed and non printed materials with a printed product marking band as required by LPS 1215: Issue 3 

Clause 4. 

Solicom SA 

Rue de Drinklange 9, L-9911 Troisvierges, Luxembourg 

Tel: +352 26957256 • Fax: +352 26958056 

E-mail: info@solicompack.com • Website: www.verisafe.be 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Verisafe 320 (White) 0.32 ±5% 320 ±5% 789b/01 

Verisafe 400 (White) 0.40 ±5% 400 ±5% 789b/02 

Verisafe B1 280 (White) 0.28 +5/-10% 280 +5/-7% 789b/03 

Note: 

1. LPCB Ref. No. 789b/01, 789b/02 & 789b/03 are available in white only and cover non-printed Verisafe material as specified with a 

printed product marking band as required by LPS 1215: Issue 3 Clause 4 only. 

20 Nov 2011 175



Sunjüt A.S. 

Yukari Dudullu, Organize San, Bölgesi I Cad. No. 29, Umraniye 34775, Istanbul, Turkey 

Tel: +44 (0)800 834704 • Fax: +44 (0)800 834705 


Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m 2 ) 

Proscaff Premium FR 0.60 250 495b/01 

Scaffnet FR (white) 0.30 (single yarn) 65 ± 5% 495b/02 

Note: 

1 LPBC Ref. 4965b/01 Covers printed and non printed materials with a printed product marking band as required by LPS1215: Issue 3 

Clause 4 

The Blinking Lamp Company Ltd 

Unit F, Motorway Distribution Centre, Avonmouth Way, Bristol BS11 9YT, United Kingdom 

Tel: +44(0) 1179 828180 • Fax: +44(0) 1179 382818 

E-mail: office@blinkinglamp.co.uk • Website: www.blinkinglamp.co.uk 

Certificate No: 915b-x1 to LPS 1215: Issue 3 

Product Name 

Thickness 

Weight 

Cert. No. 

(mm) 

(g/m²) 

Tri-Flex HD FR 0.7 ± 5% 220 +7/ - 5% 915b-x1/01 

Tri-Flex FR 0.7 ± 5% 170 ± 10% 


915b-x1/02 

Notes: 

1. LPCB Ref No. 915b-x1/01 is available in white only and covers non printed material with a printed product marking band as required 

by LPS 1215 Issue 3 Clause 4 only. 

2. LPCB Ref No. 915b-x1/02 is available in white only and covers printed and non printed material with a printed product marking band 

as required by LPS 1215 Issue 3 Clause 4. 


Product Name Thickness (mm) Weight (g/m²) Cert. No. 

Tri-Net FR 0.75 ± 10% 85 ± 15% 1061a-x1/01 

Notes: 

1. LPCB ref No. 1061a-x1/01 is available in Blue, White, Black Green, Red, Yellow and Orange and is non-printed material as specified 

with a printed marking band as required by LPS1215 Issue 3 clause 4 only. 

176 20 Nov 2011


CAVITY FIRE BARRIERS 

The materials listed in this section can be used to sub-divide such voids as service shafts, roof and floor 

spaces and restrict the spread of fire. In the absence of a specific test standard for cavity barriers these 

products meet the performance requirements of BS 476:Part 22:1987 Methods for determination of the fire 

resistance of non-loadbearing elements of construction or BS EN 1364-1Fire resistance tests for nonloadbearing 

elements, walls or 1364-2 Fire resistance tests for non-loadbearing elements, ceilings as set 

down in Approved Document B. The LPC Design Guide for the Fire Protection of Buildings: 2000 covers the 

design issues in Section 4.5. 

The assessment methodology used in LPS 1208 also applies to the performance assessment for these 

products. 

Culimeta-Saveguard Limited 

Tame Valley Mill, Wainwright Street, Dukinfield, Cheshire SK16 5NB, United Kingdom 

Tel: +44 (0)161 344 2484 • Fax: +44 (0)161 344 2486 

E-mail: sales@saveguard.com 


Product Name 

Specification 

(m) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Cert. No. 

FireHalt Gold 3.0 long x 1.2 wide 132 38 552a/01 

Notes: 

1. The barriers can only be installed vertically. 

2. Joints between individual runs in a barrier must be fixed using 12mm staples at 50mm centres. 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 



Product Name Product Specification Fire 

Resistance 

(min) 

Integrity 

Rockwool Firepro Fire ½ hour Fire 1 layer 60mm Fire Barrier foil faced 

Barrier System Barrier 

overlapped joints 

½ hour Cavity 

Barrier 

1 hour Fire 2 layers 50mm Fire Barrier staggered 

Barrier 

vertical joints 

1½ Hour Fire 2 layers 50mm Fire Barrier 

Barrier 

2 hour Fire 

Barrier 

Fire 

Resistance 

(min) 

Insulation 

Grading 

Cert. 

No. 

60 30 FR30 022c/01 

1 layer 50mm thick 60 15 FR15 

staggered vertical joints 

2 layers 60mm Fire Barrier foil faced 

separated by 40mm air gap 

60 60 FR60 

90 90 FR90 

120 120 FR120 

Notes: 

1. This product is supplied in 1m widths, with a length of 4m for 50mm thick Fire Barrier and 3.5m for 60mm thick Fire Barrier. 

2. The maximum allowable drop is 6m without a support frame. Where the additional section is joined the barrier should be overlapped 

by at least 100mm and stitched. 


20 Nov 2011 177


CAVITY FIRE BARRIERS 

Certificate No: 022c to LPS1208: Issue 2 

Rockwool Firepro Fire Barrier Slab 

Product Name 

Cavity 

Width 

(mm) 

Slab 

Size 

(mm) 

Fire 

Resistance 

(min) 

Integrity 

Fire 

Resistance 

(min) 

Insulation 

Grade 

Cert. No. 

Rockwool Firepro Fire Barrier Slab Up to 1000 1000 x 600 x 100 240 60 FR60 022c/02 

Notes: 

1. Where the slab is penetrated by services, the fire resistance is reduced to 90 minutes integrity and 60 minutes insulation. The size of 

the penetrations should not exceed steel pipes having a diameter of 33.5mm external diameter, or steel cable trays 305mm wide x 

50mm high x 0.9mm thick. Rockwool Acoustic and Fire Sealant should also be applied to all butt edges to form a tight bond when a 

penetration passes through the slab. The Acoustic and Fire Sealant should be tapered from 16mm deep at the face of the slab to 

nothing at a distance of 40mm on both faces. 


178 20 Nov 2011


LPS 1195 TEMPORARY BUILDINGS FOR USE ON CONSTRUCTION SITES 

Temporary buildings are widely used on construction sites as site offices, canteens and rest areas etc. On some 

large construction sites the number of temporary buildings can form a virtual village; a fire starting in one of these 

temporary buildings could be catastrophic if the fire were to break out and spread to other temporary buildings or 

to the building under construction. 

LPS 1195:Part 1 Specification for Testing of Temporary Buildings for Use on Construction Sites specifies the test 

and performance requirements for temporary buildings for use on construction sites at locations less than 6m 

from buildings under construction/refurbishment. The basic objective is to prevent a fire which has started in a 

temporary building from spreading to adjacent combustible materials, other temporary buildings or to the building 

under construction. A temporary building tested and approved by LPCB to this standard can be regarded as 

meeting the appropriate requirements of “The Joint Code of Practice on the Protection from Fire of Construction 

Sites and Buildings Undergoing Renovation”. 

McAvoy Group Limited 

2 Ferguson Road, Knockmore Hill Industrial Estate, Lisburn, Co Antrim BT28 2FW, United Kingdom 

Tel: +44 (0)870 2408987 • Fax: +44 (0)28 8774 88495 

E-mail: sales@mcavoygroup.co.uk • Website: www.mcavoygroup.com 


Product Name 

SafeSpace Fire rated office 

Maximum 

Size (mm) & 

Configurations 

9750(L) x 

3040(W) x 

3040(H) 

See Note 1 

Maximum 

Supporting Load 

(note 4) 

Integrity 

Performance 

Insulation 

Performance 

Irradiance 

Performance 

Cert. No. 

8.5 tonne 30 minutes 30 minutes 0.005 

kW/m 2 728a/01 

Notes: 

1. The certification applies to unit configurations as follows; 

12FT x 10FT Fire rated office, drawing reference FRO-1210-0-011 




30FT x 10FT Fire rated office, drawing reference AVO-3010-0-031-08 


Including up to 3 off 1067 x 940mm fire rated timber frame windows with external steel security shutters (Note 2) and, 1 off 762 x 

1981mm fire rated timber door with external steel security door (Note 3). 

2. Test conducted with steel security shutters in the open position. 

3. Test conducted with the steel security door in the closed position. 

4. Imposed load applied evenly distributed on a floor section located on the top of the 4 structural corner posts. 

20 Nov 2011 179


PRODUCTS ASSESSED FOR USE IN SURFACE AND SUB SURFACE TRANSPORT APPLICATIONS 

The products listed in this section have been assessed for use in rail transport applications in which the 

means of escape from a fire is limited as a result of: 

 

 

 

Difficulties in escaping from moving vehicles. 

The location of the fire (sub surface tunnels, viaducts, termini). 

Restricted egress from tunnels and sub surface termini. 

Under such circumstances, it is essential that the materials used in the construction and furnishings of 

vehicles and sub surface constructions have the appropriate fire performance in terms of fire resistance and 

reaction to fire, including spread of flame, smoke and toxic fume emission. 

This scheme provides independent third party approval for fire performance of products which have been 

tested and, where appropriate, classified in accordance with standards and codes of practice recognised by 

the transport industry or produced by the relevant transport bodies such as London Underground Limited 

(LUL), International Maritime Organisation (IMO) etc. 

Products gaining LPCB approval under this scheme are primarily for use in transport applications such as 

rolling stock, shipping, motor vehicles and within transport infrastructure such as underground tunnels and 

transport termini. 

MCT Brattberg AB 

SE 37192 Karlskrona, Sweden 

Tel: +46 (0) 455 451 60 • Fax: +46 (0) 455 451 28 

E-mail: info@mctbrattberg.com • Website: www.mctbrattberg.com 

UK Office: 

MCT Brattberg Ltd, Commerce Street, Carrs Industrial Estate, Haslingden BB4 5JT, United Kingdom 

Tel: +44 (0)1706 244890 • Fax: +44 (0)1706 244891 

E-mail: info@mctbrattberg.co.uk • Website: www.mctbrattberg.co.uk 



Construction 

RGB 2, 4 , 6, 8 & RGB 180, 240 & 360 Cables Concrete or masonry 

Floor 

Steel pipe Concrete or masonry 

Floor 


Wall 


Wall 

RGBO 2, 4 , 6, 8 & RGBO 180, 240 & 360 Cables Concrete or masonry 

Floor 


Floor 


Wall 


Wall 

RGP 50, 70, 100, 150, 200 & 300 Cables Concrete or masonry 

Floor 


Floor 


Wall 


Wall 


(min) 

Integrity 


(min) 

Insulation 

Cert. No. 

240 120 628a/01 

240 60 

240 60 

240 60 

240 120 628a/02 

240 60 

240 60 

240 60 

360 120 628a/03 

240 60 

360 120 

240 60 

180 20 Nov 2011




Construction 

RGPO 50, 70, 100, 150, 200 & 300 Cables Concrete or masonry 

Floor 


Floor 


Wall 


Wall 


(min) 

Integrity 


(min) 

Insulation 

Cert. No. 

360 120 628a/04 

240 60 

360 120 

240 60 

Note: 

1. Please refer to manufacture’s product data for maximum aperture sizes and installation details. 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022e to EN 13501-1: 2002 

Product Name 

Thickness Test/Assessment Classification Cert. No. 

(mm) 

Standard 

Cladding Roll - Unfaced 60 - 180 EN 13501-1:2002 A1 022e/01 

Cladding Roll - Aluminum foil faced 60 - 180 EN 13501-1:2002 A1 

Cladding Roll - White tissue faced 60 - 180 EN 13501-1:2002 A1 

Flexi Batts - Unfaced 50 - 150 EN 13501-1:2002 A1 022e/04 

Certificate No: 022f to BS 476: Part 24: 1987 

FirePro Fire Duct Systems 

Product Name Duct Type Condition Maximum Duct 

Size 

(ht x wt) 

(mm) 

FirePro Fire Duct 

Systems 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Cert. 

No. 

1000 x 1000 25 30 30 022f/01 

1000 x 1000 30 60 60 

1500 x 1500 50 90 90 

1500 x 1500 70 120 120 

1525 dia. 25 30 30 

1525 dia. 30 60 60 

1525 dia. 50 90 90 

1525 dia. 70 120 120 

1000 x 1000 25 30 30 

20 Nov 2011 181




Size 

(ht x wt) 

(mm) 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

1500 x 1500 40 60 60 

1200 x 1200 70 90 90 

1000 x 1000 90 120 120 

1525 dia. 25 30 30 

1525 dia. 40 60 60 

1525 dia. 70 90 90 

1525 dia. 90 120 120 

Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1000 x 1000 30 60 60 

Fire Inside 1500 x 1500 50 90 90 

Fire Inside 1500 x 1500 70 120 120 

Fire Inside 1525 dia. 25 30 30 




Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1500 x 1500 40 60 60 

Fire Inside 1200 x 1200 70 90 90 

Fire Inside 1000 x 1000 90 120 120 





Cert. 

No. 

182 20 Nov 2011




Size 

(ht x wt) 

(mm) 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Fire 

Outside 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

1000 x 1000 25 30 30 

1000 x 1000 30 60 60 

1500 x 1500 50 90 90 

1500 x 1500 70 120 120 

1525 dia. 25 30 30 

1525 dia. 30 60 60 

1525 dia. 50 90 90 

1525 dia. 70 120 120 

1000 x 1000 25 30 30 

1500 x 1500 40 60 60 

1200 x 1200 70 90 90 

1000 x 1000 90 120 120 

1525 dia. 25 30 30 

1525 dia. 40 60 60 

1525 dia. 70 90 90 

1525 dia. 90 120 120 

Fire Inside 1000 x 1000 25 30 30 

Cert. 

No. 

20 Nov 2011 183




Size 

(ht x wt) 

(mm) 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

vertical 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Smoke 

Outlet 

horizontal 

orientation 

Kitchen 

Extract 

Kitchen 

Extract 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Fire Inside 1000 x 1000 30 60 60 

Fire Inside 1500 x 1500 50 90 90 

Fire Inside 1500 x 1500 70 120 120 





Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1500 x 1500 40 60 60 

Fire Inside 1200 x 1200 70 90 90 

Fire Inside 1000 x 1000 90 120 120 





Fire 

Outside 

Fire 

Outside 

1500 x 1500 40 30 30 

1000 x 1000 90 60 60 

Cert. 

No. 


184 20 Nov 2011



FirePro TM Acoustic Intumescent sealant 

Product 

Name 

FirePro 

Acoustic 

Intumescent 

Sealant 

Element of 

Construction 

Orientation 

Element of 

Construction 

Thickness 

(mm) 

Element of 

Construction 

Material 

Maximum 

Joint 

Width 

(mm) 


Fire Side 

Depth of 

Sealant (mm) 



Backing 

Material 


50mm 

floor 230 Softwood/AC 25 12 Ethafoam 

30mm 


50mm 


50mm 


40mm 


25mm 


20mm 


50 x 25mm 


0mm 


25mm 


15mm 


25mm 


30 x 15 


15 x 15 


10 x 15 


10 x 15 


15 x 15 


30 x 15 


50mm 


50mm 

wall 200 Softwood/AC 25 12 Ethafoam 

30mm 


50mm 


40mm 


25mm 


25mm 


25mm 


20mm 


40mm 


10mm 


25mm 


Non-fire Side 

Depth of 

Sealant (mm) 

Fire 

Resistance 

(min) 

Integrity 

(E) 

Fire 

Resistance 

(min) 

Insulation 

(I) 

Cert. 

No. 

155 105 022b/05 

51 44 

47 47 

72 62 

243 65 

243 29 

10 155 47 

25 240 92 

6 240 207 

15 240 73 

53 53 

243 29 

30 265 265 

15 265 230 

10 265 265 

200 166 

227 227 

240 233 

245 82 

96 93 

55 54 

77 39 

243 44 

243 29 

40 29 

243 16 

10 240 122 

20 240 95 

10 240 240 

20 240 126 

Note: 

AC – Aerated Concrete. 

Ethafoam – Open cell polyethylene foam rod 

Please refer to Rockwool installation instructions for further details 

20 Nov 2011 185


FIRE PROTECTED TIMBER STAIRS 

The timber escape stairs listed in this section are assessed against the requirements of Scheme Document 

SD 198 which details the requirements of the approval and certification process, and BD2569 Fire 

Performance of Escape Stairs Guidance Document which details the method of test and assessment for 

escape stairs based on a realistic fire scenario. The procedure consists of a fire test to evaluate the reactionto-fire 

performance of the stair assembly and a subsequent load test to evaluate the structural performance of 

the stair assembly following a fire incident. The scheme applies only to stairs used in: 

· Single occupancy dwellings 

· Communal areas in blocks of flats 

· Areas where people may congregate as defined in Table 1 of BS 6399-13. 

This approval scheme is run in partnership with the British Woodworking Federation (BWF). 

Jeld-Wen UK Ltd 

Snow Hill, Melton Mowbray, Leicestershire LE13 1PD, United Kingdom 

Tel: 0845 122 2890 

E-mail: staircustomerservices@jeld-wen.co.uk • Website: www.jeld-wen.co.uk/stairs 

Certificate No: 1023a to SD198/BD2569 Fire Protected Timber Escape Stair 

Fire Protected Timber Escape Stair 

Product Name 

Stair 

Geometry 

Timber 

Type 

Treads/Risers 

Timber 

Type 

Other Timber 

Components 

(Strings/handrail, 

newel posts 

and balusters) 

Stair 

Treatment 

applied 

Jeld-Wen Fire Protected Stair Straight flight FR MDF / FR MDF Kerto-S / Hemlock Pressure 

Impregnation 

Straight flight FR MDF / FR MDF Kerto-S / Softwood Intumescent 

coating 

Straight flight FR MDF / FR MDF Kerto-S / Softwood Jeld-Wen 3 

part primer 

Dog-leg 

Parana 

Kerto-S / Hemlock Intumescent 

Pine/Plywood 

coating 

Dog-leg MDF / MDF Kerto-S / Hemlock Intumescent 

coating 

Dog-leg FR MFD / FR MDF Kerto-S / Hemlock Pressure 

Impregnation 

Dog-leg 

Parana 

Kerto-S / Hemlock Pressure 

Pine/Plywood 

Impregnation 

Cert. No. 

1023a/01 

1023a/02 

1023a/03 

1023a/04 

1023a/05 

1023a/06 

1023a/07 

Notes: 

1. All stair cases must be under-drawn with a single 12.5mm layer of Type F plasterboard fixed to the strings with 25mm clout nails at 

150mm maximum centres. 

2. The maximum permitted span for the treads are 1160mm between strings. 

3. LPCB ref No. 1023a/04, /05, /06 and /07 Dog-leg systems cover alternative geometries to those tested such as left or right handed 

returns with a minimum distance of 110mm between return flights and a minimum landing of 2340mm . 

4. Approved installation configurations and Timber treatment processes are shown below. 

186 20 Nov 2011



LPCB ref 

No. 

LPCB ref 

1023a/01 

Component Treatment Process Material 

Strings 

Dricon pressure impregnation fire 

retardant treatment by Arch 

Chemicals to achieve a Class 1 

surface spread of flame* 

32 x 360 Kerto-S 

Treads None 25mm Euroclass C FR MDF by 

Premier Forest Products Ltd. 

Risers None 12mm Euroclass C FR MDF by 


Newel posts 

Handrail 

Balusters 













90mm stop chamfered Hemlock 

63 x 44 Hemlock 


LPCB ref 

1023a/02 

Strings 

2 coats of Envirograf ES/VFR fire 

protection coating 12- 

15m²/litre/coat for each of 2 

coats of base coat applied in 

accordance with manufacturers 

instructions 


Treads None 25mm Euroclass B FR MDF by 


Risers None 12mm Euroclass B FR MDF by 


Newel posts 

Handrail 






instructions 






instructions 

90 x 90 softwood square stop 

chamfered 

63 x 44 softwood profiled 

20 Nov 2011 187



Balusters 






instructions 

41 x 41 softwood stop 

chamfered 

LPCB ref 

1023a/03 

Strings 

Jeld-Wen three part primer 

applied. All machined edges to 

be coated with 2 coats of 

Envirograph ES/VFR. 



Premier Forest Products Ltd 


Premier Forest Products Ltd 

LPCB ref 

1023a/04 

Newel posts 

Handrail 

Balusters 

Strings 






instructions 









Aquafire HP coating system 

comprising a primer, two part 

basecoat and two part topcoat 

applied in accordance with 

manufacturer’s instructions. 

90 x 90 softwood square stop 

chamfered 

63 x 44 softwood profiled 

41 x 41 softwood stop 

chamfered 


Treads 

Risers 











27mm Parana Pine 

15mm Plywood 

188 20 Nov 2011



Newel posts 

Handrail 













Balusters 







LPCB ref 

1023a/05 

Strings 







Treads 






25mm MDF from Premier Forest 

products Ltd. 

Risers 






12mm MDF from Premier Forest 

Products Ltd. 

Newel posts 







Handrail 







Balusters 







20 Nov 2011 189



LPCB ref 

1023a/06 

Strings 



Chemicals to achieve a Class O 







Newel posts 

Handrail 

Balusters 














LPCB ref 

1023a/07 

Strings 






Treads 





27mm Parana Pine 

Risers 





15mm Plywood 

Newel posts 

Handrail 

Balusters 
















190 20 Nov 2011

Part 

2 

FIRE DOORS AND 

SHUTTERS 

(INCORPORATING 

INSTALLER SCHEME FOR 

FIRE AND SECURITY 

DOORS)

PART 2: FIRE DOORS AND SHUTTERS (INCORPORATING INSTALLER 

SCHEME FOR FIRE AND SECURITY DOORS) 

INTRODUCTION 

Fire doors and shutters contribute to the passive fire protection of buildings by maintaining the: 

fire separation of compartment walls, while allowing the passage of persons or objects 

fire separation in shafts or service ducts that penetrate compartment floors 

protection provided by walls forming protected routes for means of escape. 

In addition to careful design and product selection, it is recommended that all products are installed and 

maintained by LPCB approved contractors who have demonstrated their competence. 

Products 

Doors and shutter assemblies are approved in accordance with: LPS 1056: Test and Evaluation 

Requirements for the Approval and Listing of Fire Doorsets, Lift Landing Doors and Shutter Assemblies. 

The fire testing element of this LPS is based on BS 476:Part 20 - Method for determination of the fire 

resistance of elements of construction (general principles) or BS EN 1634-1 Fire resistance test for doors and 

shutter assemblies- Part 1: Fire doors and shutters, BS EN 81-58 Landing doors fire resistance test and BS 

EN 1366-7 Fire resistance tests for service installations - Part 7 Conveyor systems and their enclosures. 

LPS 1056 also includes requirements for the reliability testing of the door and shutter assemblies, and 

assessment procedures for doors and shutters that are too big to be directly fire tested. 

Installation contractors 

LPCB approved installation contractors are assessed in accordance with: LPS 1271: Requirements for 

Approval and Listing of companies installing fire and security doorsets, shutters and smoke barriers. 

Maintenance contractors 

LPCB approved maintenance contractors who repair and maintain fire doors and shutters are approved in 

accordance with: LPS 1197: Requirements for LPCB Approval and Listing of Companies Undertaking the 

Maintenance and Repair of Doorsets, Shutters, and Active Smoke/Fire barriers 

192 20 Nov 2011


FIREBREAK DOORS AND SHUTTERS 

This section lists firebreak doorsets and shutters approved to LPS 1056 Test and Evaluation requirements for 

the LPCB Approval and Listing of Fire Doorsets, Lift Landing Doors and Shutter Assemblies. LPS 1056 is 

based upon relevant BS or European test criteria and not only looks at the fire integrity and insulation (where 

applicable) but also includes reliability cyclic tests and grading. 

For details of the specific fire resistance required for firebreak doors and shutters for different building types, 

see the LPC Design Guide for the Fire Protection of Buildings:2000. 

Where insulation is marked as 0, this denotes that the insulation was not measured or that it could not be 

measured in accordance with the relevant standard. 

Andreu Barbera S.L. 

Poligono Fuente Del Jarro, C/Ciudad De Sevilla, 20, 46988 Paterna, Valencia, Spain 

Tel: +34 96134 3100 • Fax: +34 961 34 0859 

E-mail: andreu@andreu.es • Website: www.andreu.es 


Product 

Name 

TURIA EI2 

60 

TURIA EI2 

90 

TURIA EI2 

120 

Door 

Type 

Double 

leaf 

hinged 

doorset 

Double 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Double 

leaf 

hinged 

doorset 

Double 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Double 

leaf 

hinged 

doorset 

Double 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Single 

leaf 

hinged 

doorset 

Max leaf 

Size 

Height 

(mm) 

Max Leaf 

Size 

Width 

(mm) 

Max Leaf Max Leaf 

Size Size 

Area Glass 

(m 2 Type 

2710 2446 6.0 25mm 

thick 

Pyrobel 

Fire 

Vision Vision Vision 

Reliability 

(mm) (mm) (m 2 

Panel 

Max 

Clear 

View 

Height 

Panel 

Max 

Clear 

View 

Width 

Panel 

Max 

Clear 

View 

Area 

Resisitance 

(minutes) 

BS476: Part 22 

Integrity / 

Insulation 

(self closing 

Durability 

Ref 

LPS10560 

Cause 3.6) 

862 756 0.59 60 / 30 No 

Performance 

Determined 

2710 2446 6.0 N/A - - - 60 / 30 No 

Performance 

Determined 

2710 1223 3.0 N/A - - - 60 / 30 No 

Performance 

Determined 

2710 1223 3.0 25mm 

thick 

Pyrobel 

2710 2446 6.0 53mm 

thick 

Pyrobel 

862 756 0.59 60 / 30 No 

Performance 

Determined 

862 728 0.57 90 / 60 No 

Performance 

Determined 

2710 2446 6.0 N/A - - - 90 / 60 No 

Performance 

Determined 

2710 1223 3.0 53mm 

thick 

Pyrobel 

862 728 0.57 90 / 60 No 

Performance 

Determined 

2710 1223 3.0 N/A - - - 90 / 60 No 

Performance 

Determined 

2710 2446 6.0 53mm 

thick 

Pyrobel 

862 728 0.57 120 / 90 No 

Performance 

Determined 

2710 2446 6.0 N/A - - - 120 / 90 No 

Performance 

Determined 

2710 1223 3.0 53mm 

thick 

Pyrobel 

862 728 0.57 120 / 90 No 

Performance 

Determined 

2710 1223 3.0 N/A - - - 120 / 90 No 

Performance 

Determined 

Cert. 

No. 

922a/01 

922a/02 

922a/03 

Notes: 

1. LPCB ref 922a/01, 922a/02 & 922a/03 Doorsets are approved when installed in concrete or masonry walls and must be fixed back to 

the supporting construction using four masonry anchors on each jamb. 

20 Nov 2011 193



2. LPCB ref 922a/01 & 922a/02 single leaf doorsets must be fitted with a Tesa model 50 lock, a Tesa model 2000N panic bar, a Tesa 

model 2000 door closer and 1 ½ pairs of steel butt hinges. Double leaf doorsets must be fitted with, on the active leaf, a Tesa model 

CF 50 lock and, on the inactive leaf, a Tesa model CF32 two-point latch; both leaves must be fitted with a Tesa model 4000N panic 

bar, a Tesa model GD2 door selector and 1 ½ pairs of steel butt hinges. In addition, one leaf must be fitted with a Tesa model 

CT2200 door closer and one with a Tesa model CT4000 door closer. 

3. LPCB ref 922a/03 single leaf door sets must be fitted with a Tesa model CF50 lock, a Tesa model 2000N panic bar, a Telesco model 

Unik Combi door closer and 1 ½ pairs of steel butt hinges. Double leaf doorsets must be fitted with, on the active leaf a Tesa model 

CF 50 lock and the inactive leaf with a Tesa model CF32 two-point latch; both leaves must be fitted with a Tesa model 4000N panic 

bar, a Tesa model CT4000+S door closer/selector and 1 ½ pairs of steel butt hinges. 

4. LPCB ref 922a/01, 922a/02 & 922a/03 The number of vision panels may be increased providing that the distance between the panes 

is no less than that between the tested pane and the edge of the leaf and that the size of the leaf cut out area is no greater than that 

of the tested doorsets. On this basis, the minimum distances between the backs of the frames of adjacent vision panels and the 

backs of the frames and the door leaf edge are 135mm for the TURIA EI2 60-minute doorsets and 147.5mm for the TURIA EI2 90- 

minute and 120-minute doorsets, and the maximum total clear view area is 0.49m² (TURIA EI2 60-minute doorsets) and 0.47m² 

(TURIA EI2 90-minute and 120-minute doorsets). 

Ascot Doors Limited 

Britannia Way Industrial Park, Union Road, Bolton BL2 2HE, United Kingdom 

Tel: +44 (0)1204 545801 • Fax: +44 (0)1204 545800 

E-mail: sales@ascotdoors.co.uk • Website: www.ascotdoors.co.uk 


Product Name Spec. Door Type Max 

Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 


(min) 

BS 476: Part 22 

Integrity 


(min) 

BS 476: Part 22 

Insulation 

Cert. No. 

A200 Series 4 Rolling shutter 7.00 7.00 49.00 240 0 131a/01 

A400 Series 4 Single - leaf hinged 2.42 1.02 2.24 240 0 131a/02 

4 Double - leaf hinged 2.42 2.04 4.48 240 0 131a/03 

Attenborough Doors Limited 

Merlin Way, Quarry Hill Industrial Estate, Ilkeston, Derbyshire DE7 4RA, United Kingdom 

Tel: +44 (0)115 9300815 • Fax: +44 (0)115 9448930 

E-mail: information@attenboroughdoor.co.uk • Website: www.attenboroughdoor.co.uk 



Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Insulation 

Cert. No. 

Attenborough Fire Shutter 4 Rolling shutter 7.00 7.00 49.00 240 0 145b/01 

Clark Door Limited 

Unit F Central, Kingmoor Park, Carlisle, Cumbria CA6 4SJ, United Kingdom 

Tel: +44 (0)1228 522321 • Fax: +44 (0)1228 401854 

E-mail: mail@clarkdoor.com • Website: www.clarkdoor.com 


194 20 Nov 2011



Fireman 

Product 

Name 

Door Type 

Max 

Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Insulation 

Reliability 

(self closing 

durability Ref. LPS 

1056 Clause 3.6) 

Fireman Sliding door 4.0 4.0 16.00 240 0 No performance 

determined 

Single leaf 2.76 1.423 3.57 240 0 No performance 

hinged door 

determined 

Double leaf 2.76 2.845 7.15 240 0 No performance 

hinged door 

determined 

Cert. 

No. 

106a/01 

106a/02 

106a/03 

Notes: 

1. Clark Door Ltd are also approved under LPS 1271 for installation of Fireman series of fire rated doorsets. 

2. 106a/02 & 106a/03 - Vision panels, 6.5mm thick Pyroshield clear glass with maximum dimensions 1000mm wide x 1000mm high. 

Maximum area 1m² 

3. 106a/03 - Double leaf doors, passive leaf must be fitted with a 3-point latching mechanism that engages in the top of frame, sill and 

the active leaf, and the active leaf must be fitted with a full length astragal that overlaps the passive leaf by at least 25mm. 

4. 106a/01, 106a/02, & 106a/03 - Door leaf skins can be fabricated from galvanised mild steel or grade 316 stainless steel. 

5. 106a/01, 106a/02, & 106a/03 - The doorsets can be installed in a rigid supporting construction such as brick, blockwork or concrete. 

The doorsets can also be installed in a composite wall panel system which provides equal or greater fire resistance than the doorset, 

when installed in a composite wall panel system the minimum fixing detail described in assessment report CC213834 shall be 

provided. 

gte Brandschutz AG 

Hamburger Straße 2, D-14532 Stahnsdorf, Germany 

Tel: +49 3329 6359-0 • Fax: +49 3329 6359-25 

E-mail: gte@gte.ag • Website: www.gte.ag 

Certificate No: 735a to LPS 1056: Issue 5 excluding installation 

Product Name Door Type Max 

Height 

(m) 

CSS 

Vertical sliding 

conveyor 

system shutter 

Horizontal 

sliding 

conveyor 


Flap type 

conveyor 


(Single) 

Flap type 

conveyor 


(Stacked) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(m) 

BS 476: Part 22 

Integrity 

Fire 

Resistance 

(m) 

BS 476: Part 22 

Insulation 

Cert. No. 

1.3 1.4 1.82 90 90 735a/01 

1.3 1.4 1.82 90 90 735a/02 

1.3 1.1 1.43 90 90 735a/03 

0.85 1.1 0.935 90 90 735a/04 

Notes: 

1. LPCB Product Ref. No’s 735a/01, /02, /03 & /04 suitable for installation into masonry walls and Durasteel partitions as described in 

Assessment report No. CC221812. 

2. CSS conveyor system shutters must be regularly maintained in line with the gte Brandschutz recommendations. 

20 Nov 2011 195



Hart Door Systems 

Redburn Road, Westerhope Industrial Estate, Westerhope, Newcastle upon Tyne NE5 1PJ, United Kingdom 

Tel: +44 (0)191 214 0404 • Fax: +44 (0)191 271 1611 

E-mail: sales@speedor.co.uk • Website: www.speedor.com 

Certificate No: 016a to LPS 1056: Issue 5 excluding installation 


Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Insulation 

Cert. No. 

Firebrand 4 Face-fixed rolling shutter 7.00 7.00 49.00 240 0 016a/01 

Note: 

1. Hart Door Systems Ltd are also approved under LPS 1271 for installation of Firebrand rolling shutters. 

Hörmann KG Freisen 

Bahnhofstrasse 43, D-66629 Freisen, Germany 

Tel: +49 (0)6855 993-0 • Fax: +49 (0)6855 993 197 

E-mail: roew.frs@hoermann.de • Website: www.hoermann.de 

Certificate No: Certificate No: 655a to LPS 1056: Issue 6 

Product 

Name 

HBS 60 C- 

1 

HBS 60 C- 

2 

HBS 90 C- 

1 

HBS 90 C- 

2 

HBS 120 

C-1 

HBS 120 

C-2 

HBS 30 D- 

1 

HBS 60 D- 

1 

HBS 90 D- 

1 

HBS 30 F- 

2 

HBS 60 F- 

2 

HBS 90 F- 

2 

Vision 

Transom 

Max clear Max clear Max clear 

Vision Vision 

Fire Reliability (self 

(mm) 

(mm) 

(m 2 Height 

(mm) 

Width 

(mm) 

Area 

(m 2 5) 

Integrity / 

Insulation 

opening 

sizes 

Max 

Height 

opening 

sizes 

Max 

Width 

opening 

sizes 

Max 

Area 

panel 

Max 

Clear 

View 

panel 

Max 

Clear 

View 

panel 

Max 

Clear 

View 

panel 

Option 

Available 

(see note 

resistance 

(min) 

BS476 Part 

22 

closing 

durability Ref. 

LPS1056 

clause 3.6) 

2500 1250 3.125 781 435 0.34 Yes 60 / 0 No Performance 

determined 


determined 


determined 


determined 

2500 1250 3.125 - - - Yes 120 / 0 No Performance 

determined 

2500 2000 5.000 - - - Yes 120 / 0 No Performance 

determined 

4225 1950 6.580 2085 1080 2.25 No 30 / 0 No Performance 

determined 


determined 


determined 

3700 3388 11.372 - - - No 30 / 30 No Performance 

determined 


determined 


determined 

Cert. 

No. 

655a/07 

655a/08 

655a/09 

655a/10 

655a/11 

655a/12 

655a/13 

655a/14 

655a/15 

655a/16 

655a/17 

655a/18 

Notes: 

1. LPCB ref No. 655a/07 & 08 for alternative approved thin/thick rebated doorsets, frame profiles, sill arrangements & door furniture 

please refer to BRE assessment report CC 94538 Review 3. 

2. LPCB ref No. 655a/09, 10, 11 & 12 for alternative approved thin/thick rebated doorsets, frame profiles, sill arrangements & door 

furniture please refer to BRE assessment report CC 92353 Review 3. 

3. LPCB ref No. 655a/13, 14 & 15 doorsets are approved with the following hardware only. 

a. Hinges - 3 x Schwarte 

b. Locking mechanism - A BKS 6065 lock with an additional BKS6138 lock 

c. Door closer - Geze TS 4000 

d. Door furniture - Eco Schulte 0432-EN 179-DO 20.3 plastic-coated steel lever handles, four dog bolts along the hinge edge. 

196 20 Nov 2011



4. LPCB ref No. 655a/16, 17 & 18 doorsets are approved with the following hardware only. 

a. Hinges - 2 pairs (4) Schwarte FH-615-20-KO on each leaf (passive/active leaf) 

b. Door closer - GEZE TS 4000 (active/passive leaf) 

c. Locking mechanism - BKS 6065 lock with additional BKS 6138 catch lock (active leaf), and BKS 1899 rebate locking bolt 

(passive leaf) 

d. Door furniture - ECO Shulte DIN 18273-FS-SG-BB-PZ lever handles (active/passive leaf) along with ECO Shulte SR Basis-1 

door selector and three security bolts. 

5. Where a doorset is fitted with a transom panel, the transom shall be up to a maximum height of 1000mm and not exceeding the 

maximum permitted height of the doorset, and be of the same construction as the door leaf which is fastened to the door frame with 

security bolts at the top and steel screws at the bottom at maximum 500mm centres. The transom panel may be fitted into the frame 

type either with or without flexible perimeter seals. For LPCB ref no 655a/07, 08, 09 & 10 a vision panel may be fitted within the 

transom panel in the same way as for the door leaf, see note 6. 

6. LPCB ref No. 655a/07, 08, 09 & 10 Vision panel frames, steel channel spacers, minimum 1.0mm thick are welded to the leaf and 

connected together through the door leaf with M5 steel screws and threaded sockets at 250mm nominal centres. The frame depth 

which holds the 6.5mm-thick Georgian-wired glass is 15 mm. Ceramic fibre tape, nominally 4mm thick, is fitted between the glass and 

the frame. The single and double leaf doorsets may be fitted with one or more vision panels providing the following requirements are 

met 

a. Where more than one panel is fitted the max total vision area must not exceed 0.34m2 and each vision panel must be 

separated by at 

least 165mm 

b. The vision panel must be a minimum of 165mm from the leaf edge. 

c. The arrangement of the vision panels in double leaf doorsets shall be the same in both leaves 

7. LPCB ref No. 655a/13, 14 & 15 Vision panel frames, comprising of 2mm-thick T-profiles, 30mm x 30mm, which are connected via 

2mm fillet welds, the tail of the T-profiles are covered on both sides with strips of Promatect-L board, 30mm x 15mm. The vision panel 

Promaglas 90/35 Type 1.0 is held in place by a 2mm-thick steel glazing bead 44.5mm x 20.5mm fixed back to the glazing support 

frame with 4.2mm Ø x 50mm long self tapping screws. The perimeter on both sides is sealed against the glazing beads using EPDM 

seals. 

8. LPCB ref No. 655a 07, 08, 09, 10,11 & 12 doorsets may be installed in either Masonry minimum 215mm-thick, Concrete/concrete 

block minimum 150mm-thick, autoclaved aerated concrete block walls minimum 215mm -thick / 400kg/m³ or Steel stud with 

plasterboard or calcium silicate board partitions. Where the doorset is installed in a plasterboard or calcium silicate board partition, the 

inside of the aperture to which the doorset is being fixed is lined with 2mm thick steel stud channel section, with flanges at least 

40mm wide. The vertical studs either side of the aperture are fixed top and bottom to either a masonry or concrete supporting 

construction, and the horizontal stud along the top of the aperture is fixed to the vertical studs at either end. The door frame shall also 

be filled with fire resisting board and fixed to the partition using 5mm diameter self-tapping self-drilling screws. 

9. LPCB ref No. 655a/13, 14, 15, 16, 17 & 18 doorsets may be installed in masonry or concrete walls minimum 240mm-thick. 

Industrial Door Engineering Limited 

Winnington Avenue, Winnington, Northwich, Cheshire CW8 4EQ, United Kingdom 

Tel: +44 (0)1606 871832 • Fax: +44 (0)1606 871482 

E-mail: sales@industrial-door-eng.co.uk • Website: www.industrial-door-eng.co.uk 



Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Insulation 

Reliability 

(self closing 

Durability Ref 

LPS 1056 

Clause 3.6) 

Sentry Rolling shutter 7.0 7.0 49.0 240 0 No 

performance 

determined 

Sentry 2 Rolling shutter 7.0 7.0 49.0 120 0 No 

performance 

determined 

Sentry 1 Compact Rolling shutter 2.20 3.40 7.48 60 0 No 

performance 

determined 

Sentry 1 Rolling shutter 2.20 2.20 4.84 60 0 No 

performance 

determined 

Cert. No. 

165a/01 

165a/02 

165a/03 

165a/04 

Notes: 

20 Nov 2011 197



1. LPCB Ref No. 165a/03 - Sentry 1 Compact rolling shutter can be fitted with either the flat or curved lath. 

2. Industrial Door Engineering Limited are also Certified for the installation of fire rated Sentry rolling shutters against the requirements 

of LPS 1271. 

J Durrance & Co Ltd 

Durrance House, 855 London Road, West Thurrock, Essex RM20 3LG, United Kingdom 

Tel: +44 (0)1708 258999 • Fax: +44 (0)1708 258900 

E-mail: sales@jdurrance.co.uk • Website: www.jdurrance.co.uk 



Height 

(m) 

Max 

Width 

(m) 

Max Area 

(m 2 ) 


(min) 

BS 476:Part 22 

Integrity 


(min) 

BS 476:Part 22 

Insulation 

Cert. No. 

PyroGuard 275 Rolling shutter 2.24 2.55 5.71 120 - 588a/01 

L.B.S. Group (incorporating L.B.S Security Services Limited - t/a Specialized Door 

Services, Russell Shutters, Olsen Shutters and Ranford Doors) 

Unit 6, Sterling Trading Estate, Rainham Road South, Dagenham, Essex RM10 8TX, United Kingdom 

Tel: +44 (0)208 526 8572 • Fax: +44 (0)208 984 0378 


Fireguard 

Product 

Name 

Fireguard 

Door Type 

Rolling 

shutter 

Max Height 

(m) 

Max Width 

(m) 

Max Area Fire Resistance Integrity/Insulation 

(m 2 (min) 

BS 476: Part 22 

Integrity 

Cert. 

No. 

7.0 10.0 49.0 240/0 247b/01 

Notes: 

1. LPCB Ref 247b/01 - for a list of the component's and sizes for the shutter dimensions up to the maximum stated please refer to 

BRE Global assessment CC203994 Rev 2. 

Lincs Doors Limited 

Innovation Way, Europarc, Grimsby, North East Lincolnshire DN37 9TT, United Kingdom 

Tel: +44 (0)1472 311057 • Fax: +44 (0)1472 311058 

E-mail: enquiries@lincsdoors.co.uk • Website: www.lincsdoors.co.uk 


Product 

Name 

Pyroshield 

Door Type 

Single leaf hinged 

without vision panel 




with vision panel 



Max 

Height 

(m) 

Max 

Width 

(m) 

Max Fire 

Area Resistance 

(m 2 (min) 

BS 476: Part 

22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Insulation 

Reliability 

(self closing 

durability 

Ref. LPS 1056 

Clause 3.6) 

2.114 0.942 1.99 120 0 No performance 

determined 


determined 


determined 


determined 

Cert. 

No. 

777a/01 

777a/02 

198 20 Nov 2011



Product 

Name 

Door Type 

Double leaf hinged 








Max 

Height 

(m) 

Max 

Width 

(m) 

Max Fire 

Area Resistance 

(m 2 (min) 

BS 476: Part 

22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Insulation 

Reliability 

(self closing 

durability 

Ref. LPS 1056 

Clause 3.6) 


determined 

2.536 2.260 4.96 60 0 No performance 

determined 


determined 

2.536 2.260 4.96 60 0 No performance 

determined 

Cert. 

No. 

777a/03 

777a/04 

Notes: 

1. Lincs Doors Ltd are also approved under LPS 1271 for installation of fire rated doorsets. 

2. 777a/02 & 777a/04 - Vision panels, 10mm thick Pyrodur glass with maximum dimensions 245mm wide x 350mm high. 

3. 777a/03 & 777a/04 - Double leaf doors, passive leaf must be fitted with a 3-point latching mechanism that engages in the top of 

frame, sill and the active leaf, and the active leaf must be fitted with a full length astragal that overlaps the passive leaf by at least 

25mm. 

4. 777a/01, 777a/02, 777a/03 & 777a/04 - Door leaf skins can be fabricated from galvanised mild steel or grade 316 stainless steel. 

5. 777a/01, 777a/02, 777a/03 & 777a/04 - The doorsets can be installed in a rigid supporting construction such as brick, blockwork or 

concrete. The doorsets can also be installed in a composite wall panel system which provides equal or greater fire resistance than 

the doorset, when installed in a composite wall panel system the minimum fixing detail described in assessment report CC223023 

shall be provided. 

Mercian Shutters Limited 

Pearsall Drive, Brades Road Industrial Estate, Oldbury, West Midlands B69 2RA, United Kingdom 

Tel: +44 (0)121 544 6124 • Fax: +44 (0)121 552 6793 

E-mail: info@merciandoors.co.uk • Website: www.merciandoors.co.uk 

Certificate No: 355b to LPS 1056: Issue 5 excluding installation 


Height 

(m) 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 22 

Insulation 

Cert. No. 

SF Series 4 Rolling shutter 7.00 7.00 49.00 60, 120 & 240 0 355b/01 

Rolling shutter 5.00 10.0 50.00 60 & 120 0 

Notes: 

1. SF series rolling shutters ref 355b/01 - Reference must be made to assessment report no CC242948 issue 2 dated 11 June 2008 to 

confirm component dimensions relevant to the system size and fire resistance required. 

2. Mercian Shutters Ltd are also approved under LPS 1271 for installation of SF Series fire rated rolling shutters. 

Middle East Insulation 

P O Box 14225, Dubai, United Arab Emirates 

Tel: +971 48801600 • Fax: +971 48801700 

Website: contact@mei-uae.com 


Product 

Name 

FORT/HC 

single leaf 

doorset 

Maximum 

leaf size 

Height 

(mm) 

Maximum 

leaf size 

Width 

(mm) 

Maximum 

leaf size 

Area (m²) 

Vision 

Panel 

Glass 

type 

Vison 

panel 

Maximum 

clear view 

height 

(mm) 

Vision 

Panel 

Maximum 

clear view 

width 

(mm) 

Vision 

panel 

Maximum 

clear view 

area (m²) 

Transom 

Panel 

Option 

Available 

(see note 

2) 

BS 476: 

Part 22 

Fire 

Resistance 

(minutes) 

Integrity 

BS 476: 

Part 22 

Fire 

Resistance 

(minutes) 

Insulation 

2967 1196 3.22 N/A - - - NO 180 0 708a/01 

2968 1056 2.84 6mm 

Pyran S 

Cert. 

No. 

500 200 0.10 YES 120 0 708a/03 

20 Nov 2011 199



Product 

Name 

FORT/HC 

double leaf 

doorset 

Maximum 

leaf size 

Height 

(mm) 

Maximum 

leaf size 

Width 

(mm) 

Maximum 

leaf size 

Area (m²) 

Vision 

Panel 

Glass 

type 

Vison 

panel 

Maximum 

clear view 

height 

(mm) 

Vision 

Panel 

Maximum 

clear view 

width 

(mm) 

Vision 

panel 

Maximum 

clear view 

area (m²) 

Transom 

Panel 

Option 

Available 

(see note 

2) 

BS 476: 

Part 22 

Fire 

Resistance 

(minutes) 

Integrity 

BS 476: 

Part 22 

Fire 

Resistance 

(minutes) 

Insulation 

2968 1056 2.84 6mm 805 230 0.17 YES 90 0 

Pyran S 

2968 1056 2.84 6mm 700 200 0.14 YES 90 0 

Pyroshield 

2968 1056 2.84 6mm 805 230 0.17 YES 60 0 

Pyroshield 

2968 1056 2.84 N/A - - - YES 120 0 

2337 1017 2.16 6mm 700 200 0.14 YES 120 0 708a/05 

Pyran S 

2337 1017 2.16 6mm 805 230 0.17 YES 90 0 

Pyran S 

2337 1017 2.16 6mm 700 200 0.14 YES 90 0 

Pyroshield 

2337 1017 2.16 6mm 805 230 0.17 YES 60 0 

Pyroshield 

2337 1017 2.16 N/A - - - YES 120 0 

2682 1196 2.91 6mm 

Pyran S 

2682 1196 2.91 6mm 

Pyran S 

2682 1196 2.91 6mm 

Pyroshield 

2682 1196 2.91 6mm 

Pyroshield 

Cert. 

No. 

254 254 0.065 YES 120 0 708a/06 

700 200 0.140 YES 90 0 

700 200 0.140 YES 90 0 

805 230 0.168 YES 60 0 

Notes: 

1. LPCB Ref. 708a/03, 708a/05 & 708a/06 Where a doorset is fitted with a transom panel, the maximum height of the doorset, including 

transom panel, should not exceed 3000mm. The transom panel should be a maximum of 580mm high and have the same 

construction as the door leaves and be separated from them by a transom bar. The panel should be fastened to the door frame using 

5mm Ø bolts via 25mm x 25mm x 60mm long x 2mm-thick clips. 

2. LPCB Ref. 708a/01, 708a/03 & 708a/06 Doorset must be fitted with two pairs of hinges per leaf. 

3. LPCB Ref. 708a/05 Doorset must be fitted with one-and-a-half pairs of hinges per leaf. 

4. The approved doorsets have been tested or assessed for use with the following hardware types; 

a. Hinges - FORT stainless steel ball bearing hinges, McKinney butt hinges. Alternative mild steel, galvanised or stainless steel 

hinges with characteristics as detailed in assessment report CC 271427. 

b. Locking mechanism - Dorma 752F. Alternative locks and latches with characteristics as detailed in assessment report CC 

271427. 

c. Door furniture - All door furniture shall be manufactured from steel or stainless steel as detailed in assessment report CC 271427. 

d. Door closer - Dorma 7601, Dorma TS72 or Geze TX4000 for use with single leaf doorsets, and Dorma TS72 for use with double 

leaf doorsets only. 

5. LPCB Ref. 708a/01, 708a/03, 708a/05 & 708a/06 the doorsets listed have been tested in a brick wall surround and are therefore 

approved when installed in masonry or concrete wall surround only. 

Saudi Factory For Fire Equipment Co. 

New Industrial Area, PO Box 58469, Riyadh 11515, Kingdom of Saudi Arabia 

Tel: +966 1 265 0070 • Fax: +966 1 265 2190 

E-mail: qa@sffeco.com.sa • Website: www.sffeco.com 

Certificate No: 403c to LPS 1056 Issue 6.1 

Product Name 

SFFECO FIRE DOOR 

Door 

Type 

Single 

leaf, 

hinged 

steel 

doorset 

Max 

Height 

(mm) 

Max 

Width 

(mm) 

Max 

Area 

(m²) 

Fire 

Resistance 

(minutes) 

BS 476: 

Part 22 

Integrity 

Fire 

Resistance 

(minutes) 

BS 476: 

Part 22 

Insulation 

Relibility 

(self closing 

durability 

Ref. LPS 

1056 Clause 

3.6) 

2197 1092 2.399 180 0 No 

Performance 

Determined 

Cert. No. 

403c/01 

Notes. 

1. LPCB Ref. No. 403c/01 The SFFECO FIRE DOOR doorset is approved to withstand a fire exposure from the opening side only, as 

detailed in BRE Assessment report CC225304. 

200 20 Nov 2011



Stobich Brandschutz GmbH 

Pracherstieg 6, D - 38644, Goslar, Germany 

Tel: 00 49 532 157080 • Fax: 00 49 532 157080 

E-mail: info@stobich.de • Website: www.stobich.com 


Product Name 

ECClos-Q 

conveyor system 

closure 

Supporting 

construction 

160mm thick 

Plasterboard 


(see note 1) 

200mm blockwork 

wall 

(see note 4) 

Penetration 

sealing 

Max leaf 

height 

(m) 

(note 3) 

Max leaf 

width 

(m) 

(note 3) 

Max leaf 

area (m) 

(note 3) 


(Min) 

BS EN 1366-7 


Cert. No. 

See note 2 1.377 1.940 2.343 120/120 1064a/01 

See note 5 

See note 6 

1.377 1.940 2.343 240/120 1064a/02 

Notes: 

1. LPCB Ref 1064a/01 - Standard flexible supporting construction according to BS EN 1366-7, table no 3, giving a fire resistance of 120 

minutes, a cross bar type steel frame consisting of two uprights spanning from the floor to ceiling with a horizontal steel spanning 

between the sections (all 100mm x 100mm x 4mm thick) is located within the partition, around the structual opening to bear the load 

of the conveyor system. The conveyor system closure shall be face fixed and may be located on the exposed or unexposed side. 

2. LPCB Ref 1064a/01 where the conveyor track penetrates the 160mm thick structural opening 1700mm (w) x 1500mm (h) a blockwork 

wall/panel is formed below (built from the finsihed floor level), minimum density 350kg/m3, 150mm thick, 800mm high and 2060mm 

wide, the top of the wall/panel is lined with a 20mm thick layer of Promatect-H board with the vertical edges protected with 100mm x 

25mm x 3mm thick steel angles through fixed to the cross bar steel frame uprights (within the partition) at 200mm centres. A nominal 

175mm opening is left around the conveyor track and blockwork wall/panel, this is built up with layers of Promatect-H25/H20/H15/H12 

and H10, Promaseal-PL boards and Tenmat Firefly 102. Two 35mm lateral gaps are left between the boards and blockwork wall 

which are friction fitted with Rockwool type RPB9 minimum density 90kg/m3 to allow movement/expansion. 

3. LPCB Ref 1064a/01 and 1064a/02 The closure leaf is 'T' shaped and may be increased by a maximum of 15% in height and/or 15% 

in width provided the surface area of the leaf is not increased by more than 20% from the dimensions given in the table above. The 

leaf may not be reduced by more than 50% in width and 75% in height. 

4. LPCB Ref 1064a/02 - Standard low density rigid wall construction according to BS EN 1366-7, table no 2, with a minimum density of 

613kg/m3. The conveyor system closure shall be face to face fixed and may be located on the exposed or unexposed side. 

5. LPCB Ref 1064a/02 where the conveyor track penetrates the 200mm thick structural opening 1700mm (w) x 1500mm (h), a 

blockwork wall/panel is formed below minimum density 350kg/m3, 150mm thick and supported 300mm above the finished floor level 

with 4 x 300mm and 1 x 500mm L profile fixing brackets 150mm x 100mm x 10mm thick with threaded rods and nuts (M10). The top 

of the wall/panel is lined with a 20mm thick layer of Promatect-H board with the vertical edges protected with 100mm x 25mm x 3mm 

thick steel angles though fixed back to the 200mm thick wall at 200mm centres. A nominal 175mm opening is left around the 

conveyor track and blockwork wall/panel, this is built up with layers of Promatect-H25/H20/H15/H12 and H10, Promaseal-PL boards 

and Tenmat Firefly 102. Two 35mm lateral gaps are left between the boards and blockwork wall which are friction fitted with 

Rockwool type RPB9 minimum density 90kg/m3 to allow movement/expansion. 

6. LPCB Ref 1064a/02 the penetration seal may incorporate a cable penetration, with maximum penetration size of 60mm x 220mm x 

175mm (thickness x height x depth). The penetration must be lined with 20mm Promatect-H boards and the perimeter of the opening 

sealed with one layer of Tenmat Firefly 102, all control cables must then individually pass through a mineral wool batt (Rockwool 

RPB9 minimum density 90kg/m3) which is held in place within the penetration with EMPE glue. 

Sunray Engineering Limited 

Kingsnorth Industrial Estate, Wotton Road, Ashford, Kent TN23 6LL, United Kingdom 

Tel: +44 (0)1233 639039 • Fax: +44 (0)1233 625137 

E-mail: sales@sunraydoors.co.uk • Website: www.sunraydoors.co.uk 


20 Nov 2011 201




Height 

(m) 

ExcluDoor 4, 2 lock 

version 

4 Single-leaf hinged 

door 

Max 

Width 

(m) 

Max 

Area 

(m 2 ) 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Integrity 

Fire 

Resistance 

(min) 

BS 476: Part 

22 

Insulation 

Cert. 

No. 

2.25 1.05 2.40 30 0 234b/01 

Notes: 

1. LPCB Ref: 234b/01 this product achieved an integrity rating of 120 minutes when tested opening towards the furnace with the 

deadlocks engaged. 

2. LPCB Ref 234b/01 this product is also certificated to Security Rating 4 against the requirements of LPS 1175: Issue 5. 

3. Sunray Engineering Ltd is also approved to LPS 1271 for installation of fire and security doors, see approval listing for details. 


Product Name 

ExcluDoor 4, Mk2 FR 

ExcluDoor 3, Mk3 FR 

Door 

Type 

Single-leaf 

hinged door 

Double-leaf 

hinged door 

Unequal 

width 

Double-leaf 

hinged door 

Single-leaf 

hinged door 

Double-leaf 

hinged door 

Unequal 

width 

Double-leaf 

hinged door 

Max 

leaf 

Height 

(m) 

Max 

leaf 

Width 

(m) 

Max leaf 

Area 

(m2) 

Fire 

Resistance 

(min) 

BS EN 1634-1: 2008 


Cert. No. 

2.350 1.155 2.71 240/0 234b/02 

2.350 1.155 5.42 240/0 234b/03 

2.350 1.155 5.42 240/0 

2.350 1.155 2.71 240/0 234b/04 

2.350 1.155 5.42 240/0 234b/05 

2.350 1.155 5.42 240/0 

Notes: 

1. LPCB Ref: 234b/02, 234b/03, 234b/04 and 234b/05 doorsets may be fitted with a plain outer face so that there is no method of 

external access. 

2. LPCB Ref: 234b/02, 234b/03, 264b/04 and 234b/05 these products are also certificated to Security Rating 4 against the requirements 

of LPS 1175: Issue 7. 

3. Sunray Engineering Ltd is also approved to LPS 1271 for installation of fire and security doors, see approval listing for details. 

4. LPCB Ref: 234b/02, 234b/03, 234b/04 and 234b/05 doorsets are approved with the following Surelock Slimline three-point lock 

system as shown below. 

202 20 Nov 2011



Description Code Entry Exit 

Key 

Access 

control 

Combination Key Turnknob Access 

control 

3-point bolting SL304 * 

Panic 

Emergency 

3-point bolting SL305 * 

3-point 

deadlocking SL301 

3 point 

deadlocking 

3-point 

SL 303 

 

 


3-point 


3-point 


3-point 


3-point 


3-point 

deadlocking SL320 * 

3-point 


3-point 


3-point 


3-point 


3-point 


3-point 


3-point 


Technocover Limited (incorporating TechnoRail and Strataform) 

Henfaes Lane, Welshpool, Powys SY21 7BE, United Kingdom 

Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 

E-mail: techadvice@technocover.co.uk • Website: www.technocover.co.uk 

Certificate No: 450g to LPS 1056: Issue 6 

Product 

Name 

Sentinel 

UltraSecure 

Door Type 

DS1/LV 

Single leaf 

outward 

opening 

hinged 

doorset 

uninsulated 

Maximum 

Leaf Size 

Height 

(mm) 

Maximum 

Leaf Size 

Width 

(mm) 

Maximum Door Hardware 

Leaf Size Variations 

(m 2 

2200 940 2.06 SM3,SM4,SM6,SM7, 

SM8,SM10,SM13,SM14, 

SM16,SM17,SM18,SM20 

SM23,SM24,SM26,SM27, 

SM28 & SM30. 

BS476: 

Part 22 

Fire 

resistance 

(minutes) 

Integrity 

BS476: 

Part 22 

Fire 

resistance 

(minutes) 

Insulation 

Cert. 

No. 

240 0 450g/01 

20 Nov 2011 203



Product 

Name 

Door Type 

DS1/LV 

Single leaf 

outward 

opening 

hinged 

doorset 

uninsulated 

DS2/LV 

Double leaf 

outward 

opening 

hinged 

doorset 

uninsulated 

DS2/LV 

Double leaf 

outward 

opening 

hinged 

doorset 

uninsulated 

Maximum 

Leaf Size 

Height 

(mm) 

Maximum 

Leaf Size 

Width 

(mm) 

Maximum Door Hardware 

Leaf Size Variations 

(m 2 

2640 1128 2.58 SM3,SM4,SM6,SM7, 



SM23,SM24,SM26,SM27, 

SM28 & SM30. 

2768 1218 2.80 SM3,SM4,SM6,SM7, 



SM23,SM24,SM26,SM27, 

SM28 & SM30. 

2215 975 2.15 SM3,SM4,SM6,SM7, 



SM23,SM24,SM26,SM27, 

SM28 & SM30. 

BS476: 

Part 22 

Fire 

resistance 

(minutes) 

Integrity 

BS476: 

Part 22 

Fire 

resistance 

(minutes) 

Insulation 

120 0 

Cert. 

No. 

120 0 450g/02 

240 0 

Notes: 

1. The Sentinel UltraSecure Doorsets are also certified to Security Level 3 & 4 against the requirements of LPS1175: Issue 6. 

2. LPCB ref 450g/01 & 450g/02, for approved Door Hardware Variations please refer to Manufacturer's Technical Literature. 

3. LPCB ref 450g/01 & 450g/02, the Sentinel UltraSecure Doorsets are approved when installed in concrete/masonry walls or drywall 

partitions. 

204 20 Nov 2011


LIFT LANDING DOORS 

This section lists lift landing doors approved to LPS 1056 Test and Evaluation requirements for the LPCB 

Approval and Listing of Fire Doorsets, Lift Landing Doors and Shutter Assemblies. LPS 1056 is based upon 

relevant BS or European test criteria and not only looks at the fire integrity and insulation (where applicable) 

but also includes reliability cyclic tests and grading. 

20 Nov 2011 205


FIRE AND SECURITY DOOR INSTALLERS 

This section lists companies approved to LPS 1271 Requirements for LPCB Approval and Listing of 

Companies Installing Fire and Security Doorsets, Shutters and Smoke Barriers. This standard was developed 

to ensure that the product performance is not compromised by poor installation of the fire door or shutter. This 

section includes manufacturers installing doors and independent installation companies. 

Information regarding the security of doors is available in Part 4: Section 5. 



Tel: +44 (0)1228 522321 • Fax: +44 (0)1228 401854 


Certificate No. 106b to LPS 1271: Issue 1 

Approved installer of Fireman series of fire rated doorsets. 

Grange Door Systems 

Unit 12, Bilston Glen Industrial Estate, Edinburgh EH20 9LZ, United Kingdom 

Tel: +44 (0)131 440 7000 • Fax: +44 (0)131 440 7003 

E-mail: admin@grangedoor.com • Website: www.grangedoor.com 


Approved installer of Kenrick Fire Stopper Face-fixed rolling shutter (LPCB Ref No 477a/01) 



Tel: +44 (0)191 214 0404 • Fax: +44 (0)191 271 1611 



Approved installer of Firebrand fire rated rolling shutters. 



Tel: +44 (0)1606 871832 • Fax: +44 (0)1606 871482 


Certificate No. 165c to LPS 1271: Issue 1 

Approved installer of Sentry, Sentry 1, Sentry 1 Compact and Sentry 2 fire rated rolling shutters. 

Kone PLC 

Global House, Station Place, Chertsey, Surrey KT16 9HW, United Kingdom 

Tel: +44 (0)8451 999 999 • Fax: +44 (0)870 7701144 

E-mail: sales.marketinguk@kone.com • Website: www.kone.co.uk 

Certificate No. 122P to LPS 1271: Issue 1 

Installation of Certified fire rated Rolling Shutters, Hinged Doorsets and Lift Landing Sliding Folding Shutters 

206 20 Nov 2011


FIRE AND SECURITY DOOR INSTALLERS 

KONE PLC 

Full UK Coverage 

Helpdesk KONE ONE Tel: +44 (0)8451 999 999 Fax: +44 (0)870 7701144 

Email@ sales.marketinguk@kone.com 



Tel: +44 (0)121 544 6124 • Fax: +44 (0)121 552 6793 


Also at: 

Mercian Industrial Doors (Southern) Limited, t/a Mercian Industrial Doors Southern, 10-12 Galleymead Road, 

Colnbrook, Slough, Berkshire SL3 0EN, United Kingdom 


Approved installer of SF series of fire rated rolling shutters. 

Prestige Fire Door Services Limited 

15 Kings Road, Fleet, Hampshire GU51 3DJ, United Kingdom 

Tel: 01252 645534 • Fax: 01252 678742 

E-mail: info@prestigefiredoorservices.com • Website: www.prestigefiredoorservices.com 

Certificate No. 1066PI to LPS 1271: Issue 1 

Approved Installer of certified fire doors and doorsets 

Safe Partnership 

3 East Street, Wareham, Dorset BH20 4NN, United Kingdom 

Tel: +44 (0)1929 551100 • Fax: +44 (0)1929 553300 

E-mail: safe@safepartnership.org • Website: www.safepartnership.co.uk 


Approved installer of Safe Partnership Ltd Safe Door timber security doors as approved under LPS 1175 (Ref Certificate 835a). 



Tel: +44 (0)1233 639039 • Fax: +44 (0)1233 625137 


Certificate No. 234e to LPS 1271: Issue 1 

Approved installer of certified Sunray Excludoor 3, Excludoor 3 MK 2 and Excludoor 4 (Ref product certificates 234b, 234c and 234d). 

20 Nov 2011 207


SERVICE AND MAINTENANCE OF DOORS 

This section lists companies approved to LPS 1197 Requirements for LPCB Approval and Listing of 

Companies Undertaking the Maintenance and Repair of Doorsets, Shutters, and Active Smoke/Fire Barriers. 

The effectiveness of a door is dependent upon regular inspection and servicing in accordance with the 

manufacturer’s recommendations. Companies approved to LPS 1197 have demonstrated their ability to carry 

out this work effectively. The listings include the geographical areas covered by the companies and the level 

of service provided. 

For the purposes of this document, the term fire door comprises any doorset or shutter assembly including 

any frame or guide, door leaf or leaves, rolling or folding curtain etc. which is designed to give a fire resisting 

capability when used for closing off permanent openings in separating elements of construction, including 

apertures for lift landing doors. This includes any side panels, vision panels or transom panels together with 

the door hardware and any seals (whether provided for the purpose of fire resistance and/or smoke control or 

for other purposes such as draught or acoustic reduction) which form the assembly. 



Tel: +44 (0)1204 545801 • Fax: +44 (0)1204 545800 


Certificate No. 131c to LPS 1197 

General servicing/maintenance Yes 

Maintenance contracts 

Yes 

24 hour answering service Yes 

24 hour emergency service Yes 

On site within 4 hours of all of England, Scotland and Wales. 

Bond Engineering (Maintenance) Ltd 

PO Box 7, North Road, Loughborough, Leicestershre LE11 1RL, United Kingdom 

Tel: 0844 5611 007 • Fax: +44 (0)1509 231638 

E-mail: info@bondengineeringuk.com • Website: www.bondengineeringuk.com 

Certificate No. 908a to LPS 1197: Issue 3 



Yes 



On site within 4 hours of call in West Midlands, Staffordshire, Hereford, Worcester, Warwickshire, Milton Keynes, Northamptonshire, 

Peterborough, Lincolnshire, Nottinghamshire, Derbyshire, South Yorkshire and Leicestershire. 

Crawford UK Limited 

Central & Southern UK 

7 Churchill Way, 35A Business Park, Chapeltown, Sheffield, South Yorkshire S35 2PY, United Kingdom 

Tel: +44 (0)870 609 4474 • Fax: +44 (0)114 257 4397 

E-mail: service.uk@crawfordsolutions.com • Website: www.crawfordsolutions.uk.com 

Certificate No. 001c to LPS 1197 

General servicing/maintenance 


Yes 

Yes 

208 20 Nov 2011





Out of office hours: Tel: +44 (0)1244 355235. 


Northern UK 

First Floor, Cedar House, Quarrywood Court, Livingston, West Lothian EH54 6AX, United Kingdom 

Tel: +44 (0)1506 417237 • Fax: +44 (0)1506 412726 

E-mail: service.uk@crawfordsolutions.com • Website: www.crawfordsolutions.uk.com 

Certificate No. 001c/02 to LPS 1197 



Yes 



Out of office hours: Tel: +44 (0)1244 355235. 



Tel: +44 (0)131 440 7000 • Fax: +44 (0)131 440 7003 


Certificate No. 573a to LPS 1197 



Yes 



On site within 4 hours of call in Scotland, Cumbria, North Lancashire, Teesside and Tyneside. 



Tel: +44 (0)1606 871832 • Fax: +44 (0)1606 871482 


Certificate No. 165b to LPS 1197 



Yes 



On site within 4 hours of call in Cheshire, Clwyd, Derbyshire, Greater Manchester, Gwynedd, Lancashire, Merseyside and Yorkshire. 

20 Nov 2011 209



Kone PLC 

Global House, Station Place, Chertsey, Surrey KT16 9HW, United Kingdom 

Tel: +44 (0)8451 999 999 • Fax: +44 (0)870 7701144 


Helpdesk KONE ONE 

KONE PLC, Global House, Station Place, Chertsey, Surrey KT16 9HW, United Kingdom 

Tel: +44 (0)8451 999 999 • Fax: +44(0)870 770 1144 


Certificate No. 122n to LPS 1197 



Yes 



Onsite within 4 hours of call, Full UK Coverage 




Tel: +44 (0)208 526 8572 • Fax: +44 (0)208 984 0378 




Yes 



On site within 4 hours of call-out in Bedfordshire, Berkshire, Buckinghamshire, Cambridgeshire, Essex, Hampshire, Hertfordshire, Kent, 

London, Norfolk, Northamptonshire, Oxfordshire, Suffolk, Surrey, East Sussex, West Sussex. 



Tel: +44 (0)121 544 6124 • Fax: +44 (0)121 552 6793 


also at: 

Mercian Industrial Doors (Southern) Limited, t/a Mercian Industrial Doors Southern, 10-12 Gallymead Road, 

Colnbrook, Slough, Berkshire SL3 0EN, United Kingdom 




Yes 



On site within 4 hours of call in Hereford and Worcestershire, Shropshire, Staffordshire, Warwickshire and West Midlands. 

210 20 Nov 2011





Tel: +44 (0)1929 551100 • Fax: +44 (0)1929 553300 





No 


24 hour emergency service No 

Scope: Area of cover, all regions of England, Wales and Northern Ireland. 

Maintenance and repair of Safe Partnership Ltd Safe Door timber security doors approved to LPS 1175 (Ref cert. 835a) only. 

Response service arising from perpetrators attempting or gaining entry into sanctuary or safe room based on agreed priority system. 

Stanair Industrial Door Services Limited 

2 Henson Way, Telford Way Industrial Estate, Kettering, Northamptonshire NN16 8PX, United Kingdom 

Tel: +44 (0)1536 482187 • Fax: +44 (0)1536 411799 

E-mail: info@stanair.co.uk • Website: www.stanair.co.uk 

Certificate No. 141a to LPS 1197- Issue 3 



Yes 



On site within 4 hours of call in Bedfordshire, Buckinghamshire, Cambridgeshire, Leicestershire, Northamptonshire. 

Tyco Fire and Integrated Solutions (the trading company for Tyco Fire and Integrated 

Solutions (UK) Limited and Tyco Fire and Integrated Solutions (Ireland) Limited) 

Tyco Park, Grimshaw Lane, Newton Heath, Manchester M40 2WL, United Kingdom 

Tel: +44 (0)161 205 2321 • Fax: +44 (0)161 455 4459 

Website: www.tycofis.com 


General servicing/maintenance No (see note) 

Maintenance contracts Yes 



On site within 4 hours of call in mainland UK. 

Note: General service/maintenance operated through Barnsley and Wigan offices. 

20 Nov 2011 211





Albion Road, Carlton Industrial Estate, Barnsley S71 3HW, United Kingdom 

Tel: +44 (0)1226 702000 • Fax: +44 (0)1226 702001 





Yes 






Unit 4, Bradley Hall Industrial Estate, Bradley Lane, Standish, Wigan WN6 0XQ, United Kingdom 

Tel: +44 (0)161 205 2321 • Fax: +44 (0)161 455 4459 





Yes 




212 20 Nov 2011

Part 

3 

SMOKE AND FIRE 

VENTILATION SYSTEMS

PART 3: SMOKE AND FIRE VENTILATION SYSTEMS 

INTRODUCTION 

Fire ventilation systems are installed to: 

Keep escape and access routes free from smoke. 

Facilitate fire fighting operations by creating a smoke free layer. 

Delay and/or prevent flashover and the subsequent full development of the fire. 

Protect equipment, furnishings, contents, etc. 

Reduce the thermal effects on structural components during a fire. 

Reduce damage caused by thermal decomposition of products and hot gases. 

The key components of smoke and fire ventilation systems, i.e. fire dampers, ductwork, smoke curtains and 

powered smoke and heat exhaust ventilation fans, are listed in this section. 

Their functions are: 

Fire dampers: 

To maintain compartmentation where air distribution ducts pass through compartment walls and 

floors. 

LPCB approves fire dampers to LPS 1162: Requirements for the approval of fire dampers. 

Fire resistant ductwork: 

To maintain compartmentation when air distribution ducts pass through compartment walls and floors 

and where fire resisting dampers are not used to provide the compartmentation. 

To achieve the same fire resistance in terms of integrity and, if required, insulation as required for the 

compartment walls or floors. 

LPCB approves fire resistant ductwork to BS 476: Part 24 Fire tests on building materials and structures: 

Method for determination of the fire resistance of ventilation ducts. 

Smoke curtains: 

To create a smoke reservoir by containing and limiting the travel of smoke. 

To channel smoke in a predetermined direction. 

To prevent or retard smoke entry to another area or void. 

LPCB approves Smoke curtains to LPS 1182: Requirements for the approval of fixed fabric smoke curtains, 

fixed metal smoke curtains and powered smoke curtains. 

Powered smoke and heat exhaust ventilation fans: 

To channel heat and smoke in a predetermined direction. 

To prevent smoke logging of the protected space. 

Powered smoke and heat exhaust ventilation fans are approved in accordance with BS EN 12101-3 Smoke 

and heat control systems. Part 3 Specification for powered smoke and heat exhaust ventilation. 

Grease filters used in commercial kitchen extract systems: 

To reduce flammable and volatile grease droplets from the cooking exhaust of commercial cooking 

equipment. 

LPCB categorises and approves grease filters in accordance with the requirements of LPS 1263: 

Requirements for the approval and listing of the fire performance of grease filters used in commercial kitchen 

extract systems. 

214 20 Nov 2011


FIRE DAMPERS 

Fire dampers are installed: 

• To maintain compartmentation where air distribution ducts pass through compartment walls and floors. 

• To achieve the same fire resistance in terms of integrity as required for compartment walls or floors. 

• To close completely as soon as a fire is detected. 

All the fire resistant dampers listed in Section 1 of this part of the list have been tested and assessed against 

the requirements of LPS 1162 Requirements and tests for the LPCB approval of fire dampers. 

Actionair 

Ruskin Air Management, Joseph Wilson Industrial Estate, South Street, Whitstable, Kent CT5 3DU, United 

Kingdom 

Tel: +44 (0)1227 276100 • Fax: +44 (0)1227 264262 

E-mail: sales@actionair.co.uk • Website: www.actionair.co.uk 


Product 

Name 

Fire 

Shield 

Model / 

Installation 

frame 

I/F damper 

horizontally 

mounted 

I/F damper 

vertically 

mounted 

I/F damper 

vertically 

mounted 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved Installation / 

Construction 

1250 1000 - Concrete Floor. 

Ref - AA10701 Mounted 

using a HEVAC/HVCA 

frame in a 150mm thick 

reinforced aerated 

concrete floor. Builders 

ties located at 500mm 

centres around the frame, 

are bent outwards and 

wired to 10mm- diameter 

stud anchors driven into 

the reveal the 15 - 60mm 

gap between the frame 

and reveal is filled with 

mortar or concrete. 

1250 1000 - Masonry/concrete Wall. 

Ref - AA/F10703 Mounted 



masonry/concrete wall. 

Builders ties located at 

400mm centres around 

the frame, 15 - 60mm gap 

between the frame and 

reveal. The ties are bent 

outwards and mortared 

into 50mm-deep pockets 

cut into the wall. 








the frame, 15 - 60mm gap 



outward and mortared 

into the gap 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

Cert. 

No. 

240 / 0 / 0 Standard 017a/01 

240 / 0 / 0 Standard 

120 / 0 / 0 Standard 

20 Nov 2011 215


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

DWFX-F 

damper 

vertically 

mounted 

+ Flange 

damper 

vertically 

mounted 

DWFX-C 

damper 

vertically 

mounted 

S&A 

damper 

vertically 

mounted 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 

1250 1000 - Drywall Partition. 


using 2 x 10mm Ø 

threaded drop rods 

attached to the damper 

via steel cleats welded to 

the top corners of the 

DWFX-F Flange (75mm 

wide x 1.2mm thick) 

which is tack welded to 

the damper casing in a 

steel stud partition 

120mm to 200mm thick. 

(see note 3) 


Ref - AA/F10707REV2 

mounted in a 

masonry/concrete wall 

minimum 150mm thick, 

the Flange (75mm wide x 

1.2mm thick) which is 

tack welded to the 

damper casing is fixed to 

the face of the wall the 

gap (25mm max) between 

the aperture and damper 

casing is filled with 

Rockwool and held in 

place with an angle flange 

to the inside of the reveal 

or Z flange to the face of 

the wall. 


Ref - AA/F10709 mounted 


threaded steel drop rods 

attached to angle section 

cleats welded to the top 

sides of the damper 

casing in a plasterboard 

partition min 100mm max 

200mm (see note 4) 


Ref - AA/F10711 Infill up 

to 675mm mounted using 

2 x 10mm Ø threaded 

steel drop rods to the 

damper via steel cleats 

welded to a flange (75mm 




Rockwool Ablative 

Coated Batt within a 

plaster board partition 

100mm thick (see notes 5 

and 6) 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 0 Standard 

120 / 0 / 0 Standard 

120 / 0 / 0 Standard 

120 / 0 / 0 Standard 

Cert. 

No. 

216 20 Nov 2011


FIRE DAMPERS 

Product 

Name 

Smoke 

Shield 

PTC 

Model / 

Installation 

frame 

S&A 

damper 

vertically 

mounted 

S&A 

damper 

vertically 

mounted 

S&A 

damper 

vertically 

mounted 

I/F damper 

horizontally 

mounted 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 














(see note 6) 





to a flange (75mm wide x 

1.2mm thick) which is 

tack welded to the 

damper casing in a 

plasterboard partition 

Stone mineral wool (60 - 

100kg/m³) is fitted around 

the damper on the 

opposite face to the 

flange, prior to a steel 

installation angle being 

riveted to the duct. (see 

note 7) 




threaded steel cleats 





masonry / concrete wall. 

Stone mineral wool (80 - 






riveted to the duct. 

1000 1000 - Concrete Floor. 




reinforced aerated 

concrete floor. Builders 

ties located at 500mm 

centres around the frame, 

are bent outwards and 

wired to 10mm- diameter 

stud anchors driven into 

the reveal the 15 - 60mm 

gap between the frame 

and reveal is filled with 

mortar or concrete. 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 0 Standard 

120 / 0 / 0 Standard 

120 / 0 / 0 Standard 

Cert. 

No. 

240 / 0 / 120 Standard 017a/04 

20 Nov 2011 217


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

I/F damper 

vertically 

mounted 

I/F damper 

vertically 

mounted 

DWFX-F 

damper 

vertically 

mounted 

+ Flange 

damper 

vertically 

mounted 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 








the frame. 15 - 60mm gap 




into 50mm-deep pockets 

cut into the wall. 








the frame. 15 - 60mm gap 


reveal the ties are bent 


into the gap 




threaded drop rods 

attached to the damper 

via steel cleats welded to 

the top corners of the 

DWFX-F Flange (75mm 




steel stud partition 

120mm to 200mm thick. 

(see note 3) 


Ref - AA/F10706REV 2 

mounted in a masonry / 

concrete wall minimum 

150mm thick, the Flange 

(75mm wide x 1.2mm 

thick) which is tack 

welded to the damper 

casing is fixed to the face 

of the wall the gap (25mm 

max) between the 

aperture and damper 

casing is filled with 

Rockwool and held in 

place with an angle flange 

to the inside of the reveal 

or Z flange to the face of 

the wall. 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

240 / 0 / 120 Standard 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

Cert. 

No. 

218 20 Nov 2011


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 

DWFX-C 1000 1000 - Drywall Partition. 




attached to angle section 

cleats welded to the top 

sides of the damper 

casing in a plasterboard 

partition min 100mm max 

200mm. (see note 4) 

S&A 

damper 

vertically 

mounted 

S&A 

damper 

vertically 

mounted 

S&A 

damper 

vertically 

mounted 













plaster board partition 

100mm thick. (see notes 

5 and 6) 














(see note 6) 

1000 1000 - Drywall Partition 




to the damper via steel 

cleats welded to a flange 




casing in plasterboard 

partition. Stone mineral 

wool ( 60 - 10kg/m³ is 

fitted around the damper 

on the opposite face to 

the flange, prior to a steel 


riveted. to the duct (see 

note 7) 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

Cert. 

No. 

20 Nov 2011 219


FIRE DAMPERS 

Product 

Name 

CSS - 

Circular 

Smoke 

Shield 

Model / 

Installation 

frame 

S&A 

damper 

vertically 

mounted 

Damper 

Horizontally 

Mounted 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 





to the damper via steel 

cleats welded to a flange 




casing in a masonry / 

concrete wall. Stone 

mineral wool (60 - 






riveted to the duct. 

- - 355 Concrete Floor. 


in a concrete floor min 

100mm thick using a 

square flange/frame (two 

sections) and assembled 

in situ using M5 tapit 

screws where the 

sections overlap each 

other. The flange on the 

upper surface is fixed 

using drywall screws, 

corner voids around the 

damper casing within the 

thickness of the floor are 

packed with compressed 

stone wool (nominal 

density 28 kg/m³) prior to 

fixing the lower 

installation frame, which 

is fixed in a similar 

manner using HA50 

Loden anchors. The 

nominal gap between the 

edge of the aperture and 

the damper casing should 

be 5mm. 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

Cert. 

No. 

120 / 0 / 120 Standard 017a/05 

220 20 Nov 2011


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

Damper 

vertically 

installed 

Damper 

vertically 

installed 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 

- - 355 Drywall Partition. 


in a plasterboard partition 

(min 100mm max 

200mm) using a square 

flange/frame (two 

sections) and assemble in 

situ using M5 tapit screws 

where the sections 

overlap each other. The 

flanges are fixed to the 

stud and track sections 

around the perimeter of 

the aperture using drywall 

screws, corner voids 

around the damper casing 

within the thickness of the 

aperture are packed with 

compressed stone wool 

(nominal density 

35kg/m³). The nominal 

gap between the edge of 

the aperture and the 

damper casing should be 

5mm. (see note 8) 

- - 355 Masonry/concrete Wall. 


in a masonry / concrete 

wall (min 100mm thick) 

using a square 

flange/frame (two 

sections) and assembled 

in situ using M5 tapit 

screws where the 


other. The flanges are 

fixed to the wall around 

the parameter of the 

aperture using M5 steel 

anchors, corner voids 

around the damper casing 

within the thickness of the 

aperture are tacked with 

compressed stone wool 

(nominal density 

35kg/m³). The nominal 

gap between the edge of 

the aperture and the 

damper casing should be 

5mm. 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

Cert. 

No. 

20 Nov 2011 221


FIRE DAMPERS 

Product 

Name 

CCS - 

Circular 

Smoke 

Shield 

CSS - 

Circular 

Smoke 

Shield 

Model / 

Installation 

frame 

Damper 

vertically 

installed 

Damper 

vertically 

installed 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 


Construction 

- - 355 Drywall Partition. 






welded to a flange which 

is a square flange/frame 

(two sections) and 

assembled in situ using 

M5 tapit screws where the 


other in a Rockwool 


within a plaster board 

partition 100mm thick. 

(See notes 9 and 10) 

- - 355 Masonry/concrete Wall. 






welded to a flange which 

is a square flange/frame 

(two sections) and 

assemble in situ using M5 

tapit screws where the 


other in Rockwool 


within a masonry / 

concrete wall. (see note 

10) 

BS EN 

1366-2 

Fire 

Performance 

(min) 

Integrity / 

Insulation / 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

Cert. 

No. 

Notes; 

1. See LPS1162 Issue 4, Table 1. 

2. LPCB ref 017a/"01 and 017a/04 damper casing and blades are manufactured from Stainless steel with the casing 

manufactured from galvanised steel. 

LPCB ref 017a/05 damper casing and blades are manufactured from galvanised steel. 

3. The partition comprised a steel framework of steel studs insulated with a layer of Rockwool RW5 (minimum density 

100kg/m³) insulation slab and clad on each face with two layers of 12.5mm-thick Type F plasterboard. With the aperture 

framed using stud and track with the web of the section set flush with the cut edges of the board, the framed aperture was 

then lined with one layer of 12.5mm-thick Type F plasterboard. The gap between the perimeter of the damper casing and 

the sides of the aperture should be no greater than 15mm wide along the top, bottom and non drive side, 40mm along the 

drive side. The gap is packed with Rockwool RW5 stone mineral wool and covered with a Type F plasterboard pattress 

overlapping the edge of the partition by minimum 65mm. 

4. The partition comprised a steel framework of steel studs insulated with a layer of Rocksilk RS33 (minimum density 



then lined with one layer of 12.5mm-thick Type F plasterboard. The gap between the vertical sides of the damper casing 

and the sides of the aperture should be no greater than 50mm wide. The gap is packed with stone mineral wool (minimum 

density 33kg/m³) the top and bottom of the damper casing fits flush with the aperture and is sealed with a bead of 

intumescent mastic to each side. A Type F plasterboard pattress overlapping the edge of the partition by minimum 75mm 

is then fixed to both sides of the partition. 




then lined with two layers of 12.5mm-thick Type F plasterboard. 

6. The Ablative Coated Batt is constructed by fitting the batt in the aperture with the longest edges orientated horizontally. 

The batts are glued into the opening and to each other using FirePro glue. The interface between the batts and the 

supporting construction is sealed with a 15mm bead of acoustic intumescent sealant. Following installation of the batts, a 

coat of Rockwool Ablative coating is applied over both sides of the completed seal. The batts should be cut to size so that 

they fit against the damper casing on all four sides and they rest against the flange which is tack welded to one face of the 

222 20 Nov 2011


FIRE DAMPERS 

damper casing. A 20mm-thick pattress of Rockwool Ablative Coated batt is fitted around the damper on the opposite face 

to the flange, prior to a steel installation angle being riveted to the duct. 




then lined with one layer of 12.5mm-thick Type F plasterboard. Stone mineral wool (60 - 100kg/m³) is fitted around the 

damper on the opposite face to the flange, prior to a steel installation angle being riveted to the duct. 

8. The partition comprised a steel framework of steel studs insulated with a layer of Stone mineral wool (minimum density 



then lined with one layer of 12.5mm-thick Type F plasterboard. 

9. The partition comprised a steel framework of steel studs insulated with a layer of Stone mineral wool (minimum density 



then lined with two layers of 12.5mm-thick Type F plasterboard. 

10. The Ablative Coated Batt is constructed by fitting the batt in the aperture with the longest edges orientated horizontally. 

The batts are glued into the opening and to each other using FirePro glue. The interface between the batts and the 

supporting construction is sealed with a 15mm bead of acoustic intumescent sealant. Following installation of the batts, a 

coat of Rockwool Ablative coating is applied over both sides of the completed seal. 

Advanced Air (UK) Limited 

PO Box 153, Burrell Way, Thetford IP24 3QU, United Kingdom 

Tel: +44 (0)1842 765657 • Fax: +44 (0)1842 753493 

E-mail: sales@advancedair.co.uk • Website: www.advancedair.co.uk 


Product 

Name 

Curtain 

Fire 

Damper 

Fire Smoke 

Control 

Damper 

Insulated 

Fire 

Damper 

Series 

Max 

Duct 

Size: 

Height 

Max 

Duct 

Size: 

Width 

Max Duct 

Size: 

Diameter 

ISO 10294-1 5 

Fire 

Resistance 

Integrity 

(min) 

0100 1000 1000 1000 E240 Vertical plane 

240 

0100 1000 1000 1000 E240 Horizontal 

plane 240 


240 

0200 1000 1000 1000 E240 Horizontal 

plane 240 


120 

1240 1000 1000 1000 E120 Horizontal 

plane 120 


120 

1250 1000 1000 1000 E120 Horizontal 

plane 120 


120 

1260 1000 1000 1000 E120 Horizontal 

plane 120 


120 

1270 1000 1000 1000 E120 Horizontal 

plane 120 

2400 1000 1000 1000 ES210/ESI205 Vertical plane 

210 

2400 1000 1000 1000 ES210 Horizontal 

plane 250 

Fire 

Resistance 

Insulation 

(min) 

Durability 

Standard 2 

Corrosion 

Marine 3 

Tests 

Cyclic 4 

Satisfactory Not tested Not 

tested 


tested 


tested 


tested 


tested 


tested 

205 Satisfactory Not tested Not 

tested 

250 

Cert. 

No. 

128a/01 

128a/02 

128a/03 

Notes: 

1. Standard LPS 1162 requirements for normal use, vertical plane. 

2. Corrosion test Appendix B LPS 1162 for marine use. 

3. Cyclic test Appendix A LPS 1162 for repeated use. 

4. LPS 1162 incorporates the requirements of ISO 10294-1 

20 Nov 2011 223


FIRE DAMPERS 

Arabian Thermal Aire Industries Company Ltd 

Al-Jubail Industrial City, Tareeg # 118, Al-Sinaiyah-31961, Kingdom of Saudi Arabia 

Tel: +966 3 341 5857 

E-mail: info@ataiksa.com • Website: www.ataico.com 


Product Name 

ATAI-Waterloo 

galvanized steel shutter 

ATAI-Waterloo 

galvanized steel 

smoke/fire damper 

Series 

Max 

Duct 

Size: 

height 

(mm) 

Max 

Duct 

Size: 

width 

(mm) 

Max 

Duct 

size: 

diameter 

(mm) 

ISO 

10294 

Fire 

Resistance 

Integrity 

(min) 2 

WFA 1000 1250 - - Horizontal 

plane - 240 

WGDB 1000 1000 - - Horizontal 

plane - 240 

Fire 

Resistance 

Insulation 

(min) 

Durability 

Standard 1 

Corrosion 

Marine 

Test 

Cyclic 

- Satisfactory Not tested Not 

tested 

- Satisfactory Not tested Not 

tested 

Cert. 

No. 

699a/01 

699a/02 

Notes: 

1. Standard LPS1162 requirement for normal use. 

2. Mounted in a steel deck assembly. 

BSB Engineering Services Limited 

Unit E, Tribune Drive, Trinity Trading Estate, Sittingbourne, Kent ME10 2PD, United Kingdom 

Tel: +44 (0)1795 422609 • Fax: +44 (0)1795 429543 

E-mail: sales@bsb-dampers.co.uk • Website: www.bsb-dampers.co.uk 


Product 

Name 

Model / 

Installation 

frame 

FSD-TD S, C & O / 

Horizontal 

plane HF 

S, C & O / 

Vertical 

plane HF 

S, C & O / 

Vertical 

plane SA 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved 

Installation/Construction 

1200 1200 1200 Ref FSD-TD M1-r4 

Mounted using a 

HEVAC/HVAC frame in a 

200mm-thick reinforced 

aerated concrete floor of 

minimum nominal density 

BS EN 

1366-2 

Fire 

performance 

(min) 

Integrity/ 

Insulation/ 

Leakage 

LPS 

1162 

Class 

(Note 1) 

Cert. 

No. 

580kg/m 3 240 / 0 / 240 Standard 828a/03 

240 / 0 / 240 Standard 

1000 1000 1000 Ref. FSD-TD M2-r4 - 

650kg/m 3 

Mounted using 

HEVAC/HVAC frame into 

an aperture in minimum 

150mm-thick lightweight 

aerated block wall of 


1000 1000 1000 Ref FSD-TD M3-r4 120 / 0 / 120 Standard 

Mounted using a sleeve & 

angles method in a min 

100mm max 200mm thick 

blockwork wall of minimum 

nominal density 650kg/m 3 

(See Note 5) 

224 20 Nov 2011


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

S, C & O / 

Vertical 

plane BF 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved 


1000 1000 1000 Infill up to 600mm Ref 

FSD-TD M4A-r4 Mounted 


threaded steel studs, 1 

either side of the damper 

casing fixed to steel cleats 

welded to the top & bottom 

of the damper casing in a 

Firetherm Intubatt 1 fire 

barrier partition. 

(See Note 6) 

BS EN 

1366-2 

Fire 

performance 

(min) 

Integrity/ 

Insulation/ 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

Cert. 

No. 

S, C & O / 

Vertical 

plane BF 

1000 1000 1000 Infill greater than 600mm 

Ref FSD-TD M4B-r4 

mounted using 2x 10mm 

Ø threaded steel studs, 1 







(See Note 6 & 7) 

120 / 0 / 120 Standard 

S, C & O / 

Vertical 

plane SA 

1000 1000 1000 Ref FSD-TD M5-r5 

mounted using a sleeve 

and angles method in a 

min 100mm max 200mm 

thick steel stud partition. 

(See Note 8) 

120 / 0 / 120 Standard 

S, C & O / 

Vertical 

plane CL 

1000 1000 1000 Ref FSD-TD M6-r4 

Mounted using 2 x 10mm 






steel stud partition within 

an opening in a masonry 

wall minimum 100mm 

thick & of minimum 

nominal density 650kg/m 3. 

(See Note 8) 

120 / 0 / 120 Standard 

S, C & O / 

Vertical 

plane BF 

1000 1000 1000 Infill up to 600mm 

Ref.FSD-TD M7A-r4 

mounted using 2 x 10mm 







barrier partition within an 

opening in a steel stud 

partition minimum 140mm 

thick. 


120 / 0 / 120 Standard 

20 Nov 2011 225


FIRE DAMPERS 

Product 

Name 

FSD- 

TD 

Model / 

Installation 

frame 

S, C & O / 

Vertical 

plane BF 

FSD-TD S, C & O / 

Vertical 

plane BF 

FD 

S, C & O / 

Vertical 

plane AF 

A, B, I, C & 

O / Vertical 

plane HF 

A, B, I, C & 

O / Vertical 

plane HF 

A, B, I, C & 

O / Vertical 

plane SA 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved 



Ref. FSD-TD M7B-r4 











thick. 

(See Note 6, 7 & 8) 


Ref FSD-TD M8-r5 









opening in a masonry wall 

minimum 100mm thick & 

of minimum nominal 

density 650kg/m 3. 


1200 1200 1200 Ref. FSD-TD M9-r5 

mounted using an angle 

frame in a min 100mm - 

max 200mm thick steel 

stud partition. 

(See Note 9) 

BS EN 

1366-2 

Fire 

performance 

(min) 

Integrity/ 

Insulation/ 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

120 / 0 / 120 Standard 

240 / 0 / 0 Standard 828a/04 

1200 1000 1000 Ref FD M1-r1 mounted 

580kg/m 3. 

using a HEVAC/HVAC 

frame in a minimum 

150mm-thick reinforced 

aerated concrete floor of 



using HEVAC/HVAC 

frame into an aperture in 

minimum 150mm-thick 

lightweight aerated block 

wall of minimum nominal 


using a sleeve & angles 

method in a min 100mm - 

max 200mm thick 

blockwork wall of minimum 


density 650kg/m 3. 240 / 0 / 0 Standard 

(See Note 5) 

120 / 0 / 0 Standard 

Cert. 

No. 

226 20 Nov 2011


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

A, B, I, C & 

O / Vertical 

plane BF 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved 


1200 1000 1000 Infill up to 600mm Ref FD 

M4A-r1 mounted using 2 x 

10mm Ø threaded steel 

studs, 1 either side of the 

damper casing fixed to 

steel cleats welded to the 

top & bottom of the 




(See Note 6) 

BS EN 

1366-2 

Fire 

performance 

(min) 

Integrity/ 

Insulation/ 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 0 Standard 

Cert. 

No. 

A, B, I, C & 

O / Vertical 

plane BF 


Ref FD M4B-r1 mounted 










120 / 0 / 0 Standard 

A, B, I, C & 

O / Vertical 

plane SA 


using a sleeve and angles 

method in a min 100mmmax 

200mm thick steel 

stud partition. 


120 / 0 / 0 Standard 

A, B, I, C & 

O / Vertical 

plane CL 

1200 1000 1000 Ref FD M6-r1 







steel stud partition within 

an opening in a masonry 

wall minimum 100mm 

thick & of minimum 


(See Note 8) 

120 / 0 / 0 Standard 

A, B, I, C & 

O / Vertical 

plane BF 

1200 1000 1000 Infill up to 600mm Ref FD 

M7A-r1 mounted using 2 

x 10mm Ø threaded steel 

studs, 1 either side of the 

damper casing fixed to 

steel cleats welded to the 

top & bottom of the 






thick. 


120 / 0 / 0 Standard 

20 Nov 2011 227


FIRE DAMPERS 

Product 

Name 

Model / 

Installation 

frame 

A, B, I, C & 

O / Vertical 

plane BF 

Maximum 

Duct size 

Width 

(mm) 

Maximum 

Duct size 

Height 

(mm) 

Maximum 

Duct size 

Diameter 

(mm) 

Approved 



Ref FD M7B-r1 











thick. 

(See Note 6, 7 & 8) 

BS EN 

1366-2 

Fire 

performance 

(min) 

Integrity/ 

Insulation/ 

Leakage 

LPS 

1162 

Class 

(Note 1) 

120 / 0 / 0 Standard 

Cert. 

No. 

A, B, I, C & 

O / Vertical 

plane BF 


Ref FD M8-r1 mounted 









opening in a masonry wall 

minimum 100mm thick & 

of minimum nominal 

density 650kg/m 3. 


120 / 0 / 0 Standard 

A, B, I, C & 

O / Vertical 

plane AF 

1200 1000 1000 Ref. FD M9 mounted 

using an angle frame in a 

min 100mm - max 200mm 

thick steel stud partition. 

(See Note 9) 

120 / 0 / 0 Standard 

Notes: 

1. See LPS 1162: Issue 4. Table 1 

2. LPCB Ref No. 828a/04 approval covers FD dampers constructed from galvanised steel only. 

3.. LPCB Ref No. 828a/03, approval covers FSD-TD dampers constructed from a galvanised steel casing with stainless steel blades, 

with the exception of the FSD-TD-AF damper which has galvanised steel casing with galvanised blades. 

4. The sleeve protrudes from each face of the wall by at least 20mm. The continuous external angles (minimum 40mm x 40mm) are 

riveted to the sleeve on both sides of the wall at maximum 150mm centres. Similar internal angles secure the sleeve to the damper 

casing. 

5. The Firetherm Intubatt 1 fire barrier system comprises of 2 layers of 50mm-thick Firetherm Intubatt 1 (minimum density 180kg/m³) 

seperated by a cavity of 40mm and factory coated on both faces with a 1mm-thick coating of ablative mastic. The perimeter of the 

coated batts is retained within galvanised steel angles, 50mm x 50mm x 2m, secured at maximum 300mm centres. The junctions 

between the damper and the coated batt are pattressed on both sides of the barrier with strips of Firetherm Intubatt 1, 50mm thick x 

150mm wide, which are secured by bedding on a layer of Intucoat mastic and fixing with steel pig-tail screws at maximum 200mm 

centres. Maximum distance between the damper and the reveal of the wall opening is 600mm. 

6. A perimeter frame work of steel angles 50mm x 50mm x 2mm is secured on each side of the opening between the damper and the 

reveal of the wall at 300mm centres. Steel angles are then fixed back-to-back at 300mm centres to form T-sections, which are then 

fixed around the damper to form a frame, of which its sides are no more than 600mm from the damper. The T-section from is 

secured to the perimeter frame using a series of T-sections positioned at maximum 600mm centres in one direction and 1200mm 

centres in the other direction. For barriers where the distance between the top of the damper and the top of the barrier is greater than 

1.5m, a deflection head detial is required. The maximum distance between the damper and the wall or floor must not exceed 3m. 

7. The Partition comprised of a steel framework of 50mm studs clad on each face with two layers of 12.5mm-thick Firecheck GTEC 

plasterboard, with the voids between the studs insulated with one layer of 25mm-thick Knauf Acoustic Partition Roll (minimum density 

19.5kg/m³) with the aperture to be lined with one layer of 12.5mm-thick Firecheck GTEC plasterboard. The dry fit sleeve & angle 

system comprises of a 1.2mm-thick top hat section damper casing and 300mm long sleeves with 40mm x 40mm angle type frame 

work riveted to the sleeve using 4.8mm Ø steel rivets, centrally positioned within the aperture to act as a carrier frame. 

8. The Partition comprised of a steel framework, of 50mm studs clad on each face with two layers of 12.5mm-thick Firecheck GTEC 

plasterboard, with the voids between the studs insulated with one layer of 50mm-thick Rockwool Flexi Slab (minimum density 

35kg/m³), with the aperture to be lined with one layer of 12.5mm-thick Firecheck GTEC plasterboard. The angle frame comprises of a 

steel angle formed from 1.2mm steel and is secured to one side of the damper casing using stitch welds 6-10mm long, at nominal 

150mm centres. The leg of the angle fixed to the damper casing is 35mm long. The other leg of the angle must be long enough to 

228 20 Nov 2011


FIRE DAMPERS 

overlap the partition and be secured at nominal 300mm centres. On the other side of the partition the damper is pattressed on all four 

sides using one or more layers of 12.5mm-thick Firecheck GTEC plasterboard cover strips which must overlap the partition by at least 

65mm. The cover strips are secured using suitable screws at 300mm centres. A bead of fire/acoustic sealant must be applied 

between the edges of each pattress and the spigot & between each pattress and the spigot & between each pattress and the face of 

the partition. 

20 Nov 2011 229


FIRE RESISTANT DUCTS 

Fire resistant ductwork is installed: 

 

 

To maintain compartmentation when air distribution ducts pass through compartment walls and floors 

where fire resisting dampers are not used to provide the compartmentation 

To achieve the same fire resistance in terms of integrity, and if required insulation, as required for the 

compartment walls or floors. 

All the fire resistant ducts listed in Section 2 of this part of the list have been tested and assessed against the 

requirements of BS 476:Part 24 Fire tests on building materials and structures: Method for determination of 

the fire resistance of ventilation ducts. 

Certification is limited to the applications and fire resistances given. 



Tel: +44 (0)1279 634 230 • Fax: +44 (0)1279 634 231 



Product Name Duct Type Condition Type of 

Insulation 

(kg/m 3 ) 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Cert. No. 

Flamebar BW11 Ventilation Fire outside - - 120 15 277a/01 

Ventilation Fire outside - - 240 15 

Ventilation Fire outside 45 25 120 60 











Ventilation Fire outside 105 100** 240 240 

Ventilation Fire inside - - 120 - 


Ventilation Fire inside 45 25 120 30 










Ventilation Fire inside 105 100** 240 120 

Smoke outlet Fire outside - - 120 15 


Smoke outlet Fire outside 45 25 120 60 











Smoke outlet Fire outside 105 100** 240 240 

230 20 Nov 2011




Insulation 

(kg/m 3 ) 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Smoke outlet Fire inside - - 120 - 


Smoke outlet Fire inside 45 25 120 30 










Smoke outlet Fire inside 105 100** 240 120 

Kitchen extract Fire outside - - 120 15 


Kitchen extract Fire outside 60 50 120 28* 









Kitchen extract Fire outside 105 100** 240 60* 

Kitchen extract Fire inside - - 120 - 


Kitchen extract Fire inside 45 25 120 30 










Kitchen extract Fire inside 105 100** 240 120 

Cert. No. 

Notes: 

1. All ducts are protected with 0.7mm to 1.0mm nominal thickness of Flamebar BW11 Fire Proofing. 

2. Maximum hanger centres are 1500mm for fire ratings up to two hours and 1000mm for fire ratings up to four hours. 

3. The 50mm thick x 60kg/m 3 density mineral wool insulation may be in the form of either slabs or wrap. 

* Refers to internal face inside furnace. 

** Includes 500mm x 25mm x 105kg/m 3 density mineral wool collar around duct on both sides of penetration seals through fire 

compartment walls and floors. 

Firespray International Limited 


Tel: +44 (0)1279 634 230 • Fax: +44 (0)1279 634 232 

E-mail: info@firespray.eu.com • Website: www.firespray.eu.com 



Insulation 

(kg/m 3 ) 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 

Cert. No. 

Flamebar BW11 Ventilation Fire outside - - 120 15 415a/01 

Ventilation Fire outside - - 240 15 



20 Nov 2011 231




Insulation 

(kg/m 3 ) 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 










Ventilation Fire outside 105 100** 240 240 













Ventilation Fire inside 105 100** 240 120 














Smoke outlet Fire outside 105 100** 240 240 













Smoke outlet Fire inside 105 100** 240 120 












Kitchen extract Fire outside 105 100** 240 60* 









Cert. No. 

232 20 Nov 2011




Insulation 

(kg/m 3 ) 

Insulation 

Thickness 

(mm) 

Fire 

Resistance 

Integrity 

(min) 

Fire 

Resistance 

Insulation 

(min) 





Kitchen extract Fire inside 105 100** 240 120 

Cert. No. 

Notes: 

1. All ducts are protected with 0.7mm to 1.0mm nominal thickness of Flamebar BW11 Fire Proofing. 

2. Maximum hanger centres are 1500mm for fire ratings up to two hours and 1000mm for fire ratings up to four hours. 

3. The 50mm thick x 60kg/m 3 density mineral wool insulation may be in the form of either slabs or wrap. 

* Refers to internal face inside furnace. 

** Includes 500mm x 25mm x 105kg/m 3 density mineral wool collar around duct on both sides of penetration seals through fire 

compartment walls and floors. 

Flameshield Products Limited 

9 Zillah Gardens, Wigmore, Gillingham, Kent ME8 0EE, United Kingdom 

Tel: 01322 558887 

E-mail: neil.david@btconnect.com 


Product 

Name 

Duct Type Condition Type / density of 

insulation 

Insulation 

Thickness 

(mm) 


(Integrity/ 

stability) 

Fire 

Resistance 

(Insulation) 

Flameshield Ventilation Fire inside None - 240 - 785a/03 

Smoke outlet Fire inside None - 120 - 

Kitchen Fire inside None - 120 - 

extract 

Ventilation Fire 

None - 120 - 

outside 

Smoke outlet Fire 

None - 120 

outside 

Kitchen Fire 

None - 120 - 

extract outside 

Ventilation Fire inside Mineral wool 165 40 120 30 785a/04 

kg/m3 

Ventilation Fire inside Mineral wool 165 55 120 60 

kg/m3 


kg/m3 


kg/m3 

Ventilation Fire Mineral wool 165 30 120 30 

outside 

kg/m3 


outside 

kg/m3 


outside 

kg/m3 


outside 

kg/m3 

Smoke outlet Fire inside Mineral wool 165 40 120 30 

kg/m3 


kg/m3 


kg/m3 


kg/m3 

Smoke outlet Fire Mineral wool 165 30 120 30 

outside 

kg/m3 

Smoke outlet Fire 

outside 

Mineral wool 165 

kg/m3 

40 120 60 

Cert. 

No. 

20 Nov 2011 233



Product 

Name 

Duct Type Condition Type / density of 

insulation 

Smoke outlet 

Smoke outlet 

Kitchen 

extract 

Kitchen 

extract 

Kitchen 

extract 

Kitchen 

extract 

Fire 

outside 

Mineral wool 165 

kg/m3 

Fire Mineral wool 165 

outside 

kg/m3 

Fire inside Mineral wool 165 

kg/m3 

Fire inside Mineral wool 165 

kg/m3 


outside 

kg/m3 


outside 

kg/m3 

Insulation 

Thickness 

(mm) 


(Integrity/ 

stability) 

Fire 

Resistance 

(Insulation) 

45 120 90 

50 120 120 

45 120 30 

90 120 60 

45 120 30 

90 120 60 

Cert. 

No. 

Notes: 

1. LPCB Ref. No's. 785a/03 and 785a/04 - Uninsulated and Insulated ductwork systems to be manufactured and installed to the 

specifications as detailed in BRE Assessment Report CC 255037 Issue 5 dated 8 July 2011. 

2. LPCB Ref. No's 785a/03 and 785a/04 - Covers rectangular and flat oval ductwork up to 3000mm wide x 2000mm deep, reference 

Flameshield Tables 1 - Issue F & 4 - Issue E and circular ductwork up to 1250mm diameter, reference Flameshield Tables 5 - Issue D 

and 6 - Issue D. The Flameshield systems may also be employed as attenuator casings as defined in BRE Assessment Report CC 

255037 Issue 5 dated 8 July 2011 however the LPCB approval does not cover the attenuator itself. 

4. LPCB Ref. No's 785a/03 and 785/04 - Approval also covers Uninsulated and Insulated ductwork systems manufactured to 

Flameshield Table 20 - Issue F for ventilation duct applications only with a fire resistance intergrity and stability period of up to 120 

minutes and where applicable, an insulation period as detailed in BRE Assessment Report CC 255037 Issue 5 dated 8 July 2011. 

Ductwork manufacturers: 

The following Companies manufacture the products listed on this certificate to a specification issued and controlled by Flameshield. 

These companies are audited by the LPCB to ensure the product certification requirements are met. 

Kent Ductwork Limited (LPCB Ref. 785a(1)) 

Unit 7/9 Crayford Ind Est 

Swaisland Drive 

Crayford 

Dartford 

DA1 4HS 

E & S Heating and Ventilation Limited (LPCB Ref. 785a(2)) 

Diplocks Way 

Hailsham 

East Sussex 

BN27 3JF 

Gardner & Co. (Kent) Limited (LPCB Ref. 785a(3)) 

Unit 2, 23 Revenge Road 

Lordswood Industrial Estate 

Chatham 

Kent 

ME5 8UD 

Whitehouse Engineering Co. Limited (LPCB Ref. 785a(4)) 

14 Trench Road 

Mallusk 

Newtownabbey 

Co. Antrim 

Northern Ireland 

BT36 4UU 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 


Certificate No: 022f to BS476 : Part 24 : 1987 

234 20 Nov 2011


size (ht x wt) 

(mm) 

FirePro Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Insulation 

Thickness 

(mm) 


Integrity 

(min) 




Insulation 

(min) 

Cert. No. 

Fire Outside 100 x 1000 25 30 30 022f/01 

Fire Outside 1000 x 1000 30 60 60 

Fire Outside 1500 x 1500 50 90 90 

Fire Outside 1500 x 1500 70 120 120 

Fire Outside 1525 dia. 25 30 30 




Fire Outside 1000 x 1000 25 30 30 

Fire Outside 1500 x 1500 40 60 60 

Fire Outside 1200 x 1200 70 90 90 

Fire Outside 1000 x 1000 90 120 120 





Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1000 x 1000 30 60 60 

Fire Inside 1500 x 1500 50 90 90 

Fire Inside 1500 x 1500 70 120 120 




20 Nov 2011 235





(mm) 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Insulation 

Thickness 

(mm) 


Integrity 

(min) 


Insulation 

(min) 


Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1500 x 1500 40 60 60 

Fire Inside 1200 x 1200 70 90 90 

Fire Inside 1000 x 1000 90 120 120 





Fire Outside 1000 x 1000 25 30 30 

Fire Outside 1000 x 1000 30 60 60 

Fire Outside 1500 x 1500 50 90 90 

Fire Outside 1500 x 1500 70 120 120 





Fire Outside 1000 x 1000 25 30 30 

Fire Outside 1500 x 1500 40 60 60 

Fire Outside 1200 x 1200 70 90 90 

Fire Outside 1000 x 1000 90 120 120 



Cert. No. 

236 20 Nov 2011





(mm) 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

vertical 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Ventilation 

horizontal 

orientation 

Insulation 

Thickness 

(mm) 


Integrity 

(min) 


Insulation 

(min) 



Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1000 x 1000 30 60 60 

Fire Inside 1500 x 1500 50 90 90 

Fire Inside 1500 x 1500 70 120 120 





Fire Inside 1000 x 1000 25 30 30 

Fire Inside 1500 x 1500 40 60 60 

Fire Inside 1200 x 1200 70 90 90 

Fire Inside 1000 x 1000 90 120 120 





Kitchen extract Fire Outside 1500 x 1500 40 30 30 

Kitchen extract Fire Outside 1000 x 1000 90 60 60 

Cert. No. 

20 Nov 2011 237


SMOKE CURTAINS 

Smoke curtains are used: 

 

 

 

To create a smoke reservoir by containing and limiting the travel of smoke. 

To channel smoke in a predetermined direction. 

To prevent or retard smoke entry to another area or void. 

All the smoke curtains listed in Section 3 of this part of the list have been tested and assessed against the 

requirements of LPS 1182 Requirements and tests for fixed fabric smoke curtains, fixed metal smoke curtains 

and powered smoke curtains. 

238 20 Nov 2011


POWERED SMOKE AND HEAT EXHAUST VENTILATION 

Powered smoke and heat exhaust ventilation fans are used: 

 

 

To channel heat and smoke in a predetermined direction. 

To prevent smoke logging of the protected space. 

All the fans listed have been approved against the requirements of BSEN 12101-3 Smoke and heat control 

systems. Part 3 Specification for powered smoke and heat exhaust ventilation. 

Elta Fans Limited 

17 Barnes Wallis Road, Segensworth East Industrial Estate, Farnham, Hampshire PO15 5ST, United 

Kingdom 

Tel: +44 (0) 1489 566555 • Fax: +44 (0) 1489 566555 

E-mail: mailbox@eltafans.co.uk • Website: www.eltafans.com 

Additional Manufacturing Site 

46 Third Avenue, Pensnett Trading Estate, Kingswinford, West Midlands DY6 7US, United Kingdom 

Certificate No: 937a to BS EN 12101-3: 2002 

20 Nov 2011 239



Product Name Model Application 

Classes 

SmokeVent axial fan (notes 2, 5, 6, 7, 

8) 

JetVent Impulse (flanged - standard 

thrust) axial fan (notes 2, 5, 6, 7, 8) 

LCS025, 

LCS031, 

LCS035, 

LCS040, 

LCS045, 

LCS050, 

LCS056, 

LCS063, 

LCS071, 

LCS080, 

LCS090, 

LCS100, 

LCS112, 

LCS125, 

LCS140, 

LCS160, 

LCS180, 

LCS200, 

SCS025, 

SCS031, 

SCS035, 

SCS040, 

SCS045, 

SCS050, 

SCS056, 

SCS063, 

SCS071, 

SCS080, 

SCS090, 

SCS100, 

SCS112, 

SCS125, 

SCS140, 

SCS160, 

SCS180, 

SCS200, 

LCSCR025, 

LCSCR031, 

LCSCR035, 

LCSCR040, 

LCSCR045, 

LCSCR050, 

LCSCR056, 

LCSCR063, 

LCSCR071, 

LCSCR080, 

LCSCR090, 

LCSCR100, 

LCSCR112, 

LCSCR125, 

LCSCR140, 

LCSCR160, 

LCSCR180, 

LCSCR200 

JFSU-CPA-315 

2/4-3, 

JFSU-CPA-400 

2/4-3, 

JFSU-CPA-400 

2-3, 

JFSR-CPA-315 

2/4-3, 

JFSR-CPA-400 

2/4-3, 

JFSR-CPA-400 

2-3 

insulated or 

uninsulated; 

smoke reservoir or 

non smoke 

reservoir; dual 

purpose or 

emergency use 

insulated or 

uninsulated; 


non smoke 

reservoir; 

dual purpose or 

emergency use 

Response 

delay 

Resistance 

to fire 

class 

Motor 

temp. 

rating1 

N/A F200 Class F 

/ 

Class H 


/ 

Class H 

Cert. 

No. 

937a/01 

240 20 Nov 2011




Classes 

JetVent Impulse (flanged - enhanced 



8) 

LCS031-CPU 

2/4-3, 

LCS035-CPU 

2/4-3, 

LCS040-CPU 

2/4-3, 

LCS031-CPR 

2/4-3, 

LCS035-CPR 

2/4-3, 

LCS040-CPR 

2/4-3 

LCS025, 

LCS031, 

LCS035, 

LCS040, 

LCS045, 

LCS050, 

LCS056, 

LCS063, 

LCS071, 

LCS080, 

LCS090, 

LCS100, 

LCS112, 

LCS125, 

LCS140, 

LCS160, 

LCS180, 

LCS200, 

SCS025, 

SCS031, 

SCS035, 

SCS040, 

SCS045, 

SCS050, 

SCS056, 

SCS063, 

SCS071, 

SCS080, 

SCS090, 

SCS100, 

SCS112, 

SCS125, 

SCS140, 

SCS160, 

SCS180, 

SCS200, 

LCSCR025, 

LCSCR031, 

LCSCR035, 

LCSCR040, 

LCSCR045, 

LCSCR050, 

LCSCR056, 

LCSCR063, 

LCSCR071, 

LCSCR080, 

LCSCR090, 

LCSCR100, 

LCSCR112, 

LCSCR125, 

LCSCR140, 

LCSCR160, 

LCSCR180, 

LCSCR200 

insulated or 

uninsulated; 


non smoke 

reservoir; 


emergency use 

insulated or 

uninsulated; 


non smoke 

reservoir; 


emergency use 

Response 

delay 

Resistance 

to fire 

class 

Motor 

temp. 

rating1 


/ 

Class H 

N/A F300 4 Class F 

/ 

Class H 

Cert. 

No. 

937a/02 

20 Nov 2011 241




Classes 

JetVent impulse (flanged - standard 


JetVent impulse (flanged - enhanced 



8) 

JetVent centrifugal (Mark I) fan (notes 

3, 5, 8) 

JFSU-CPA-315 

2/4-3, 

JFSU-CPA-400 

2/4-3, 

JFSU-CPA-400 

2-3, 

JFSR-CPA-315 

2/4-3, 

JFSR-CPA-400 

2/4-3, 

JFSR-CPA-400 

2-3 

LCS031-CPU 

2/4-3, 

LCS035-CPU 

2/4-3, 

LCS040-CPU 

2/4-3, 

LCS031-CPR 

2/4-3, 

LCS035-CPR 

2/4-3, 

LCS040-CPR 

2/4-3 

LCS025, 

LCS031, 

LCS035, 

LCS040, 

LCS045, 

LCS050, 

LCS056, 

LCS063, 

LCS071, 

LCS080, 

LCS090, 

LCS100, 

LCS112, 

LCS125, 

SCS025, 

SCS031, 

SCS035, 

SCS040, 

SCS045, 

SCS050, 

SCS056, 

SCS063, 

SCS071, 

SCS080, 

SCS090, 

SCS100, 

SCS112, 

SCS125, 

LCSCR025, 

LCSCR031, 

LCSCR035, 

LCSCR040, 

LCSCR045, 

LCSCR050, 

LCSCR056, 

LCSCR063, 

LCSCR071, 

LCSCR080, 

LCSCR090, 

LCSCR100, 

LCSCR112, 

LCSCR125 

JISU-CPC-50N, 

JISU-CPC-100N, 

insulated or 

uninsulated; 


non smoke 

reservoir; 


emergency use 

insulated or 

uninsulated; 


non smoke 

reservoir; 


emergency use 

insulated or 

uninsulated; 


non smoke 

reservoir; 


emergency use 

uninsulated; 

smoke reservoir; 


emergency use 

Response 

delay 

Resistance 

to fire 

class 

Motor 

temp. 

rating1 


/ 

Class H 


/ 

Class H 


/ 

Class H 


/ 

Class H 

Cert. 

No. 

937a/03 

937a/04 

242 20 Nov 2011




Classes 

JetVent -centrifugal (Mark II) fan 

(notes 3, 5, 8) 

JetVent impulse (unflanged - 

standard thrust) axial fan (notes3, 5, 

8) 

JISU-2-CPC- 

50N, 

JISU-2-CPC- 

100N, 

JVSU-CPA-315 

2/4-3, 

JVSU-CPA-400 

2-3, 

JVSU-CPA-400 

2/4-3, 

JVSR-CPA-315 

2/4-3, 

JVSR-CPA-400 

2-3 

JVSR-CPA-400 

2/4-3 

uninsulated; 

smoke reservoir; 


emergency use 

uninsulated; smoke 

reservoir; 


emergency use 

Response 

delay 

Resistance 

to fire 

class 

Motor 

temp. 

rating1 


/ 

Class H 


/ 

Class H 

Cert. 

No. 

937a/05 

937a/06 

Notes: 

1. Motor temperature rating - classes given refer to temperature rise at ambient and motor insulation as detailed in section 4.2 of EN 

12101-3: 2002. 

2. Both horizontal and vertical installation is permitted. 

3. Horizontal installation only is permitted. 

4. Tested to 300°C for 120 minutes. 

5. Only certified accessories should be used. 

6. Use of guide vanes is permitted. Where this is the case the model code has +GV added, e.g. LCS025+GV. 

7. Fan coding of units held within Select stock will be prefixed by the letter ‘S’, and the size expressed in mm (i.e. LCS025 becomes 

SLCS250) 

8. No ducted cooling air is required. 

20 Nov 2011 243


GREASE FILTERS USED IN COMMERCIAL KITCHEN EXTRACT SYSTEMS 

LPS 1263 Requirements for the LPCB Approval and Listing of the Fire Performance of Grease Filters Used in 

Commercial Extract systems. 

This standard covers the test procedures and method of calculating the fire performance rating of grease 

filters used for the reduction of flammable and volatile grease droplets from the cooking exhaust of 

commercial cooking equipment in such situations as restaurant kitchens, canteens or similar food preparation 

areas where it is necessary to reduce the cooking exhause via a ventilation system. 

Halton Foodservice Limited 

11 Laker Road, Airport Industrial Estate, Rochester, Kent ME1 3QX, United Kingdom 

Tel: +44 (0)1634 666111 • Fax: +44 (0)1634 666333 

E-mail: kelly.hiley@halton.com • Website: www.halton.com/foodservice 

Certificate No: 996a to LPS 1263 issue 1.2 

Product Name 

Nominal 

filter size 

(w x h x t) (mm) 

Nominal 

flow rate 

(m 3 /h) 

LPS 1263 Grade 

Cert. No. 

KSA Filter 498 x 330 x 51.6 786 GF90 996a/01 

Notes: 

1. LPCB ref 996a/01 The KSA filter is manufactured from Grade 304 S16 stainless steel with 0.4mm thick filter fins and 0.8mm casing. 

2. LPCB ref 996a/01 KSA filter is approved as part of a Kitchen Ventilation system with 400, 555 and 555UV canopy profiles only. 

244 20 Nov 2011

Part 

4 

SECURITY PROTECTION 

PRODUCTS

PART 4: SECURITY PROTECTION PRODUCTS 

INTRODUCTION 

Security products and services approved by LPCB play an important role in protecting people and property 

against physical attack, burglary, vandalism and terrorism. 

Statistics from the UK indicate that the addition of appropriate security measures to a home reduces the risk 

of burglary from 25% to 2.4%. However, it is important that the measures installed are effective. LPCB 

approval ensures that products developed for use in domestic applications offer effective levels of deterrence 

and, when required, will resist determined attack by a criminal wishing to gain access to a property. 

The threat to organisations from commercial crime and terrorism is diverse in both geography and levels of 

skill involved, it is persistent and requires appropriate measures to deter criminals and terrorists. Improved 

detection backed up by a fast and effective response, and effective physical security that provides a suitable 

delay while the response arrives, reduces the likelihood of such act being committed. This is supported by 

research and initiatives, in the UK, LPCB works closely with Insurers, Government, Police, end users and 

security equipment specifiers to develop methods by which the quality of product performance and product 

reliability can be assessed. Using security products approved by LPCB to protect people and assets is an 

effective way of mitigating many of the risks associated with crime and terrorism. 

The products listed in this section have been rigorously tested in programmes designed to evaluate resistance 

to deliberate attack. 

The scope of the approval of each product is described in the relevant section and on the certificates issued to 

the approved manufacturer. It is important to ensure that specifiers only select products covered by the scope 

detailed on the certificate since products outside that scope may not provide an equivalent level of security. 

The range of products listed in this section is extensive and includes physical barrier type products, asset 

marking, computer protection equipment as well as electronic detection and surveillance equipment. The 

range and scope of products submitted for approval continues to grow significantly. 

Products are approved in accordance with a range of standards. The details of these standards are given at 

the front of each section relevant to the product. 

246 20 Nov 2011


INTRUDER DETECTION EQUIPMENT 

This section lists components of intruder detection systems where compliance with the applicable EN 50131 

series of standards has been demonstrated by LPCB’ experts and most importantly on going assessments 

confirm the component continues to comply with the requirements. 

The LPCB’s intruder detection approval schemes reference Loss Prevention Standards LPS 1602 and LPS 

1603 which incorporate the requirements of the corresponding EN 50131 series of standards. The Loss 

Prevention Standards also include specific checks to confirm the intruder detection components are suitable 

for use in installations complying with the United Kingdom’s document PD 6662 Scheme for the application of 

European Standards for intruder and hold-up alarm systems and the confirmation technology requirements of 

BS 8243 in support of the ACPO security systems policy. 

By obtaining LPCB approval to the relevant LPS, conformance to the applicable requirements of the various 

European standards, published documents, and policies can be demonstrated. 

Control and Indicating Equipment 

LPS 1603 Requirements for LPCB Approval and Listing of Intruder Alarm Control and Indicating Equipment is 

the standard used for the certification of security system control and indicating equipment. The purpose of this 

LPS is to list requirements of the performance and suitability for use in installations complying with the United 

Kingdom’s document PD 6662 Scheme for the application of European Standards for intruder and hold-up 

alarm systems. 

The requirements are based on the criteria described in the European Standard EN 50131-3 and where 

appropriate to the criteria of BS 8243 in support of the ACPO security systems policy. 

Intruder Alarm Movement Detectors 

LPS 1602 Requirements for LPCB Approval and Listing of Intruder Alarm Movement Detectors is the standard 

used for the certification of intruder alarm movement detectors. This Loss Prevention Standard specifies the 

requirements for LPCB approval of the following types of intruder alarm movement detectors; 

 

 

 

 

Passive infrared 

Microwave 

Combined passive infrared and microwave 

Combined passive infrared and ultrasonic 

The purpose of this LPS is to list requirements of the performance of intruder alarm movement detectors and 

their suitability for use in installations complying with United Kingdom’s document PD 6662 ‘Scheme for the 

application of European Standards for intruder and hold-up alarm systems’. The requirements are based on 

the criteria described in the European Standards of EN 50131-2-2, EN 50131-2-3, EN 50131-2-4 and EN 

50131-2-5 respectively and to the criteria of BS 8243 in support of the ACPO security systems policy. 

LPCB approval to this LPS is applicable only to intruder alarm movement detectors intended for mounting 

inside the premises i.e. not externally located. 

Note: At the time of going to print no intruder detection equipment was listed as LPCB approved. Please 

check www.redbooklive.com for updates. 

20 Nov 2011 247


ALARM TRANSMISSION EQUIPMENT AND SIGNALLING SYSTEMS 

This section lists alarm transmission equipment suitable for use with intruder alarm and hold-up systems. 

Alarm transmission and fault warning routing equipment suitable for use with fire alarm systems is listed in 

Volume 1 Part 1 Section 10.1. 

Where alarm transmission equipment is suitable for use with both intruder alarm and hold-up systems and fire 

alarm systems, the entry for the approved equipment will appear in Volume 2 Part 4 Section 1.2 and Volume 1 

Part 1 Section 10 of the Red Book. 

The following standard is currently used for the approval scheme: 

• LPS 1277 Requirements for LPCB Approval and listing of Alarm Transmission Systems and Equipment 

Where appropriate within LPS 1277, reference has been made to published standards for intruder alarm and 

hold-up systems including EN 50131-1 together with the alarm transmission equipment standards of EN 

50136. 

Particular emphasis is placed on the verification of manufacturers’ claims by measuring alarm transmission 

times over the transmission path(s) between the equipment under test and the corresponding receiving 

centre. The response to the reporting of fault conditions is measured in a similar way. 

The results of these measurements are expressed in terms of alarm transmission system (ATS) performance 

criteria classification, using the parameters D, M, T and where applicable S and I. 

Where: 

D = Transmission time classification 

M = Transmission time maximum values 

T = Reporting time classification 

S = Substitution Security 

I = Information Security 

Availability is considered a key parameter under LPCB approval and is therefore included within the 

requirements of LPS 1277 and the resultant performance is expressed using the parameter ‘A’ for Availability. 

The measured parameters are used to determine the performance classification in terms of ATS level (1 to 6) 

that when used in conjunction with warning devices provide the security grade of the intrusion and hold-up 

alarm system (I&HAS) as defined in EN 50131-1. 

Products compliant with LPS 1277 Issue 3.0 meet ‘enhanced’ ATS performance classification which includes 

timed ‘stepped up’ reporting after the loss of the primary path and the reporting of a catastrophic failure, in 

event of the simultaneous loss of multiple transmission paths. 

To assist specifiers in their selection of the products most appropriate for protecting their risks, the actual 

performance parameters measured during the LPCB test programme are included with the product 

listing entry in the Redbook as an indicator of the level of performance that can be expected from the alarm 

transmission system. 

Compliance with relevant safety standards and applicable mandatory directives is a 

pre-requisite of LPCB approval and listing. Regular product auditing and regular factory inspections are 

carried out by LPCB ensuring high manufacturing standards and continued compliance with the applicable 

product standard. 

Note 

Since LPCB uses national and international standards for the listing of products, in some instances, the 

requirements of these standards may conflict with the recommendations of local codes of practice. We 

recommend that specifiers seek advice from the relevant local authorities and amend their specifications 

accordingly. 

248 20 Nov 2011


ALARM TRANSMISSION EQUIPMENT AND SYSTEMS 

The equipment listed in this section has been assessed against the requirements and tests methods of LPS 

1277 Requirements for LPCB Approval and listing of Alarm Transmission Systems and Equipment. 

Those components of the alarm transmission system normally located in the protected premises are listed. 

The alarm transmission and fault monitoring performance has been verified by testing the alarm transmission 

equipment in conjunction with the appropriate transmission networks. 

Specifiers are advised to check the product listing for the issue of LPS 1277 against which the alarm 

transmission equipment is approved. At the time of going to print, the current publication of LPS 1277 was 

Issue 3.0. 

Please check www.redbooklive.com for the current publication and the latest product listings. 

BT Redcare 

Monument TE, 11-13 Great Tower Street, London EC3R 5EA, United Kingdom 

Tel: +44 (0) 800 800 828 • Fax: +44 (0)20 7929 6490 

Website: www.redcare.bt.com 

Certificate No: 775a to LPS 1277: Issue 2.2 

Alarm Transmission Equipment 

Product Name Fire 

Category 

Security 

Grade 

Primary Transmission 

Path 

UC-372G-UK B 3 Asynchronous digital subscriber line 

ASSURE STAR 

(ASDL) operated by BT Broadband 

Secondary 

Transmission Path 

General packet radio service 

(GPRS) on a BT mobile network 

Cert. 

No. 

775a/01 

Performance Parameters 

Transmission 

Path 

Transmission 

Time 


Transmission 

Time 

Max. Values 

Reporting Time 


Substitution 

Security 

Information 

Security 

Network 

Availability 5 

Primary D4 M3 2 T5 S2 I3 A3 

Secondary D4 M3 2 T3 3 S2 I3 A1 

Combined 1 D4 M3 2 T5 4 S2 I3 A3 

Approved Ancillaries 

AO100 External base antenna (short) 

BA900-5 High gain antenna (long) 

CAB0106 10m low loss extension cable 

UltraCapture8 Video Card 

UltraCapture4 Video Card 

Notes: 

1. The combined performance parameters are shown for the ASSURE STAR as a whole, i.e. with both primary and secondary 

transmission paths operational. The alarm transmission performance parameters of the ASSURE STAR are consistent with those of 

ATS 5. 

2. During a planned maintenance procedure the ASSURE STAR will achieve performance classification D4 at a maximum transmission 

time classification M2. The maintenance procedure will be operated approximately four times per year and will be of approximately 5 

minutes duration. 

3. The loss of the secondary path following a previous failure of the primary path results in a reporting time classification of T4. 

4. The simultaneous loss of the primary and secondary transmission paths results in a reporting time classification of T5. 

5. Network availability classifications have been based on the limited availability data. At the time of the initial evaluation only a limited 

number of ASSURE STAR alarm transmission equipment were in service and these were subject to interruption due to engineering 

trials whilst the data was being recorded. The monitoring of network availability continues and the classification will be updated when 

available. When operating with both transmission paths functioning correctly the combined system availability will meet classification 

A3. 

20 Nov 2011 249



WebWayOne Ltd 

11 Kingfisher Court, Hambridge Road, Newbury, Berkshire RG14 5SJ, United Kingdom 

Tel: +44 (0)1635 231500 • Fax: +44 (0)1635 231539 

E-mail: sales@webwayone.co.uk • Website: www.webwayone.co.uk 


Alarm Transmission Equipment 

Certificated Products 

22-5005 WebWay 

The WebWay IP/GPRS LPS I&HAS comprises equipment part no. 22-5005 plus 

IP/GPRS LPS I&HAS configuration part no. '1411AD155002' 

Suitable for use with EN 50131-1 compliant I&HAS up to and including security grade 4, 

22-5015 WebWay 

GPRS/PSTN LPS I&HAS 

notification Option C. 

The WebWay GPRS/PSTN LPS I&HAS comprises equipment part no. 22-5015 plus 

configuration part no. '1411AD155004' 

Suitable for use with EN 50131-1 compliant I&HAS up to and including security grade 3, 

notification Option C. 

Cert. No. 

1022b/01 

1022b/02 

Approved with the following Ancillaries 

22-5054 High performance disc antenna 

22-5049-5m High gain extension antenna with 5 metre cable 




22-5076 PSTN Dialler PCB module 

22-5073 RS232 Serial interface module 

22-5076 Modem capture alarm panel interface module 

The alarm transmission equipment is to be used in accordance with the installation instructions and the guidance of ANNEX C described 

in LPS 1277 Issue 3.0 ‘Requirements for LPCB Approval and Listing of Alarm Transmission Equipment’. 

The performance of the above listed products has been found to meet the intrusion and hold-up alarm requirements of LPS 1277 Issue 

3.0 with the following performance parameters: 

Alarm Transmission System Performance Parameters 

22-5005 Webway IP/GPRS LPS I&HAS 

Product Name 

Fire Category 

LPCB 

Performance 


Designated Transmission Paths 

Primary Secondary Duplicate 

Cert No 

WebWay 

IP/GPRS LPS 

I&HAS 

N/A 

Dual Path 

Enhanced 

ATS 5 

Broadband 

(IP) 

GPRS N/A 1022b/01 

Confirmed Performance Parameters 

Transmission 

time 

Classification 1) 

Transmission 

time 

Max. Values 1) 

Reporting time 


Substitution 

Security 1) 

Information 

Security 1) 

Netw ork 

Availability 2) 

Enhanced 

Performance 

Rating 

D4 M3 T4 S2 I3 A4 ATS 5 

1) 

Minimum performance parameters for primary or secondary path. 

2) Network Availability confirmed with both designated primary and secondary paths operating. 

ATS path failure 

250 20 Nov 2011



ATS path failure conditions 

Loss of Primary path only 

(i.e. secondary path remaining operational) 

Loss of Secondary path only 

(i.e. primary path remaining operational) 

Loss of Secondary path w hilst operating in ‘stepped up’ reporting mode 

(i.e. the loss of Secondary path some time after a previous loss of the Primary path). 

Reporting catastrophic 3) failure of ATS commensurate w ith 



T4 

T3 

T4 

Enhanced 

ATS 5 

3) The detected loss of the primary path followed by immediate detection of loss of the Secondary path. 

__________________________________________________________________________________________ 

22-5015 Webway GPRS/PSTN LPS I&HAS 

Product Name 

Fire Category 

LPCB 

Performance 


Designated Transmission Paths 

Primary Secondary Duplicate 

Cert No 

WebWay 

GPRS/PSTN 

LPS I&HAS 

N/A 

Dual Path 

Enhanced GPRS PSTN N/A 1022b/02 

ATS 4 Plus 

Confirmed Performance Parameters 

Transmission 

time 

Classification 1) 

Transmission 

time 

Max. Values 1) 

Reporting time 


Substitution 

Security 1) 

Information 

Security 1) 

Netw ork 

Availability 2) 

Enhanced 

Performance 

Rating 

D3 M3 T3 Plus S2 I3 A4 ATS 4 Plus 

1) 

Minimum performance parameters for primary or secondary path. 

2) Network Availability confirmed with both designated primary and secondary paths operating. 

ATS path failure 

ATS path failure conditions 

Loss of Primary path only 

(i.e. secondary path remaining operational) 

Loss of Secondary path only 

(i.e. primary path remaining operational) 

Loss of Secondary path w hilst operating in ‘stepped up’ reporting mode 

(i.e. the loss of Secondary path some time after a previous loss of the Primary path). 

Reporting catastrophic 3) failure of ATS commensurate w ith 



T 3 Plus 

T3 

T3 Plus 

Enhanced 

ATS 4 Plus 

3) The detected loss of the primary path followed by immediate detection of loss of the Secondary path. 

20 Nov 2011 251


SAFES, STRONGROOMS AND SECURE SAFE CABINETS 

This section lists safes, strongrooms and secure safe cabinets that have been designed for the secure 

storage of cash and valuables, but which may also be used to secure other high risk assets, including secure 

information. 

The safes, strongrooms and security cabinets listed are graded according to their resistance to manual 

intervention attack tests. These are undertaken by experienced laboratory test engineers using tools carefully 

selected to achieve access to the contents of the safe using the minimum time and resistance units possible. 

Domestic safes and those typically fitted in hotel bedrooms are generally graded in accordance with EN 

14450 Secure Storage units - Requirements, classification and methods of test for resistance to burglary - 

Secure safe cabinets. 

Commercial safes and strongrooms are either graded in accordance with LPS 1183 Specification for safe 

storage units. Part 1: Safes and strongrooms or 

EN 1143-1 Secure storage units. Requirements, classification and methods of test for resistance to burglary. 

Safes, strongroom doors and strongrooms. 

Deposit safes are graded in accordance with EN 1143-2 Secure storage units. Requirements, classification 

and methods of test for resistance to burglary. Deposit systems. 

Cash and Jewellery Ratings 

Table 1 indicates typical cash and jewellery ratings attributed to safes and strongrooms according to their 

approved resistance grade. These ratings should only be used as a guide since each insurer defines their 

own ratings depending on the performance of the safes and the situation in which the safes and strongrooms 

are to be used. Specifiers are strongly advised to discuss the issue of cash and jewellery ratings with their 

insurer prior to selecting a safe or strongroom. 

Table 1: Typical Cash and Jewellery Ratings for Safes and Strongrooms 

Standard Resistance grade Typical overnight cash 

rating (£k) 

Typical overnight 

jewellery rating (£k) 

EN 14450 

S1 2 20 

S2 4 40 

LPS 1183 and EN 1143-1 

0 6 60 

I 10 100 

II 17.5 175 

III 35 350 

IV 60 600 

V 100 1000 

VI 150 1500 

VII to XIII - - 

Compatible Locks 

The locks that have been approved for use on each of the approved safes and strongrooms are listed in the 

'compatible locks' section of each manufacturer’s entry in the Red Book. Specifiers and end users are advised 

that the performance of the safes to the relevant standards is dependent on them being fitted with the locks 

listed. 

Installation and maintenance 

It is important to ensure that safes are installed in accordance with the manufacturer’s instructions and that all 

exposed fixings, the substrate into which the device is fitted and the locking mechanisms are regularly 

checked to ensure that they are in good condition and that they have not been tampered with. 

252 20 Nov 2011


SAFES 

The safes listed in this section are approved by LPCB to one or more of the following standards: 

EN 1143-1 Secure storage units. Requirements, classification and methods of test for resistance to 

burglary. Safes, strongroom doors and strongrooms. 

LPS 1183 Specification for safe storage units. Part 1: Safes and strongrooms 

Copies of LPS 1183 can be downloaded free of charge from our website www.RedBookLive.com. 

Explosion (EX) Designation 

This designation indicates a product offers resistance to detonation of a PETN (Pentaerythritol tetranitrate) 

explosive charge followed by post detonation tool attacks aimed at achieving entry to the safe. Where the use 

of explosive charges is perceived to be a threat it is recommended products with this designation are 

selected. 

Core Drill (CD) Designation 

This designation is only applicable to safes achieving grades IV and above. This designation reflects the 

ability of a product to pass the diamond drill test specified within EN 1143-1 which is designed to demonstrate 

the product’s superior resistance to methods of forced entry that solely involve the use of diamond core drills. 

Dudley Safes Limited 

Unit 17 Deepdale Works, Deepdale Lane, Upper Gornal, Dudley, West Midlands DY3 2AF, United Kingdom 

Tel: +44 (0)1384 239991 • Fax: +44 (0)1384 455129 

Website: www.dudleysafes.com 

Certificate No: 304a to LPS 1183: Issue 4 and BS EN 1143-1: 2005 

Free-standing Safes 

Product Name Size Reference Security 

Cert. No. 

Grade 

Europa 0 1 to 7 0 304a/01 

Europa I 1 to 7 I 304a/02 

Europa II 1 to 7 II 304a/03 

Europa III 2 to 7 III 304a/04 

Europa II (Mk.2) 1 to 7 II 304a/05 

Europa 0 (Mk.2) 1 to 7 0 304a/06 

Europa I (Mk.2) 1 to 7 I 304a/07 

Europa III (Mk. 2) 2 to 7 III 304a/08 


20 Nov 2011 253


SAFES 

Model Type Europa Safe (LPCB Ref. No. 304a/..) 

01 02 03 04 05 06 07 08 

Auditcon 52 Electronic Combination 

Caw i 2648 Mechanical Key 

Kaba 252 Electronic Combination 


Kaba MAS 552 Electronic Combination 

LaGard 1985 Mechanical Combination 


LaGard 3740 Electronic Combination 

LaGard Combogard 33E Electronic Combination 



M-Locks EM3520 Electronic Combination 


Mauer 70079 Mechanical Key 

Mauer 71111 Mechanical Key 

Opus 060/EM25.20 Electronic Combination 

S&G 6730 Mechanical Combination 


Godrej & Boyce Mfg. Co. Ltd. (Security Equipment Division) 

Plant - 17, Pirojshanagar, Vikhroli, Mumbai 400 079, India 

Tel: +91 22 679 64771 • Fax: +91 22 679 61509 

E-mail: securityexports@godrej.com or secure@godrej.com • Website: www.godrej.com 

Certificate No: 954b to BS EN 1143-1: 2005 + A1: 2009 and LPS 1183: Issue 4 


Product Name 

Euro Cash Grade 

3 


4 


5 

Size 

Ref: 

Minimum 

External 

Height 

(mm) 

Maximum 

External 

Height 

(mm) 1 

Minimum 

External 

Width 

(mm) 

Maximum 

External 

Width 

(mm) 1 

Minimum 

External 

Depth 

(mm) 

Maximum 

External 

Depth 

(mm) 1 

Nominal 

Weight 

(kg) 

Security 

Grade 

Cert. 

No. 

T14 485 - 485 - 498 - 173 III 954b/01 

T19 615 - 435 - 498 - 185 III 

T23 715 - 550 - 648 - 285 III 

T28 830 - 580 - 673 - 337 III 

T35 1030 - 640 - 748 - 453 III 

T43 1230 - 640 - 748 - 530 III 

T51 1430 - 630 - 748 - 600 III 

T63 1730 - 800 - 693 - 768 III 

T70 1900 - 860 - 748 - 903 III 

F23 715 - 550 - 648 - 397 IV 954b/02 

F28 830 - 580 - 673 - 462 IV 

F35 1030 - 640 - 748 - 618 IV 

F43 1230 - 640 - 748 - 727 IV 

F51 1430 - 640 - 748 - 892 IV 

F63 1730 - 800 - 693 - 1092 IV 

F70 1900 - 860 - 748 - 1307 IV 

P23 715 - 550 - 648 - 397 V 954b/03 

P28 830 - 580 - 673 - 462 V 

P35 1030 - 640 - 748 - 618 V 

P43 1230 - 640 - 748 - 727 V 

P51 1430 - 640 - 748 - 892 V 

P63 1730 - 800 - 693 - 1092 V 

P70 1900 - 860 - 748 - 1307 V 

254 20 Nov 2011


SAFES 

Product Name 


6 


0 


1 

Size 

Ref: 

Minimum 

External 

Height 

(mm) 

Maximum 

External 

Height 

(mm) 1 

Minimum 

External 

Width 

(mm) 

Maximum 

External 

Width 

(mm) 1 

Minimum 

External 

Depth 

(mm) 

Maximum 

External 

Depth 

(mm) 1 

Nominal 

Weight 

(kg) 

Security 

Grade 

Cert. 

No. 

H21 735 - 570 - 665 - 567 VI 954b/04 

H26 850 - 600 - 690 - 667 VI 

H24 790 - 690 - 730 - 720 VI 

H35 1090 - 690 - 730 - 924 VI 

H47 1390 - 690 - 830 - 1219 VI 

H55 1590 - 690 - 830 - 1359 VI 

H67 1890 - 940 - 830 - 1898 VI 

Z14 455 555 455 555 465 565 81 2 0 954b/05 

Z14S 455 555 405 505 370 470 68 2 0 

Z19 585 685 405 505 465 565 90 2 0 

Z19D 485 785 420 620 515 715 121 2 0 

Z23 485 885 420 620 515 715 135 2 0 

Z28 600 1000 450 650 540 740 159 2 0 

Z28W 600 1000 510 710 615 815 181 2 0 

Z35 800 1200 510 710 615 815 214 2 0 

Z35W 800 1200 700 900 615 815 257 2 0 

Z43 1000 1400 510 710 615 815 245 2 0 

Z43W 1000 1400 700 900 615 815 293 2 0 

Z51 1200 1600 510 710 615 815 278 2 0 

Z51W 1200 1600 700 950 615 815 331 2 0 

Z59 1400 1600 420 520 420 620 242 2 0 

Z59W 1400 1600 460 610 420 520 263 2 0 

A14 455 555 455 555 465 565 122 2 I 954b/06 

A14S 455 555 405 505 370 470 100 2 I 

A19 585 685 405 505 465 565 136 2 I 

A19D 485 785 420 620 515 715 201 2 I 

A23 485 885 420 620 515 715 211 2 I 

A28 600 1000 450 650 540 740 252 2 I 

A28W 600 1000 510 710 615 815 288 2 I 

A35 800 1200 510 710 615 815 342 2 I 

A35W 800 1200 700 900 615 815 414 2 I 

A43 1000 1400 510 710 615 815 395 2 I 

A43W 1000 1400 700 900 615 815 476 2 I 

A51 1200 1600 510 710 615 815 449 2 I 

A51W 1200 1600 700 950 615 815 539 2 I 

A59 1400 1600 420 520 420 620 384 2 I 

A59W 1400 1600 460 610 420 520 424 2 I 


Manufacturer Model Type Euro Cash Safes (LPCB Ref. No. 954b/..) 

1 2 3 4 5 6 

Carl Wittkopp GmbH 1824-159-0 Mechanical key 

Carl Wittkopp GmbH / Tw in Lock 7220 Electronic 

 

Insys Microelectronics 

combination 

Kaba AG. 

SL523 and SL525 Electronic 

combination 

Kaba Ilco Corp. 673000 Mechanical 

 

combination 

Kaba Ilco Corp. A673000 Mechanical 

 

combination 

Kaba Mauer GmbH President 71111 Mechanical key 

20 Nov 2011 255


SAFES 

Kaba Mauer GmbH Variator B - 70076 Mechanical key 

Kaba Mauer GmbH Praetor B - 70079 Mechanical key 

Kaba Mauer GmbH Variator A 70091 Mechanical key 

Kaba Mauer GmbH Variator A 70092 Mechanical key 

Kaba Mas Corp Auditcon 2 Electronic 

combination 

Kaba Mas Corp Auditcon 2100D Electronic 

combination 

Kaba Mas Corp Auditcon 3100 Electronic 

combination 

Kaba Mas Corp Cencon Electronic 

combination 

La Gard 1947 Mechanical 

 

combination 

La Gard 1985 Mechanical 

combination 

La Gard 3330-1 Mechanical 

 

combination 

La Gard 3332 Mechanical 

combination 

La Gard Combogard 3740 Electronic 

 

(Combo Basic) combination 

La Gard Combogard 6040 Electronic 

 

(39E) 

combination 

La Gard 

Combogard 66E Electronic 

 

w ith deadbolt combination 

Low e and Fletcher Ltd 3007 Mechanical key 

Low e and Fletcher Ltd 3012 Mechanical key 

Alternative Trade Names 

The Euro Cash safes are also marketed under the following alternative trade names 

Trade Name 

Alternative Trade Names 

Euro Cash Grade 0 Euro Cash Z-Series Euro Trader Grade 0 Euro Trader Z-Series 

Euro Cash Grade 1 Euro Cash A-Series Euro Trader Grade 1 Euro Trader A-Series 

Euro Cash Grade 3 Euro Cash T-Series Euro Trader Grade 3 Euro Trader T-Series 

Euro Cash Grade 4 Euro Cash F-Series Euro Trader Grade 4 Euro Trader F-Series 

Euro Cash Grade 5 Euro Cash P-Series Euro Trader Grade 5 Euro Trader P-Series 

Euro Cash Grade 6 Euro Cash H-Series Euro Trader Grade 6 Euro Trader H-Series 

Notes: 

1. If no maximum dimension is noted, the model is only approved in a single size; i.e. that listed in the minimum dimension column. 

2. The nominal weights noted vary by +/- 5% depending on the size of safe manufactured within the range of dimensions noted for that 

model. 

Certificate No: 954c to LPS 1183: Issue 4.2 

Free-standing Safe 

Product 

Name 

Size 

Ref. 

Minimum 

External 

Height 

(mm) 

Euro 

Cash 

Grade 5 

Maximum 

External 

Height 

(mm) 

Minimum 

External 

Width 

(mm) 

Maximum 

External 

Width (mm) 

Minimum 

External 

Depth 

(mm) 

Maximum 

External 

Depth (mm) 

Security 

Grade 

P62 1703 1706 688 691 748 751 V 954c/01 

Cert. 

No. 

256 20 Nov 2011


SAFES 


Manufacturer Model Type 

Kaba AG. Models SL523 and SL525 Electronic combination 

Kaba Mas Corp Auditcon 2100D Electronic combination 

Kaba Mas Corp Auditcon 3100 Electronic combination 

Kaba Mas Corp Auditcon 2 Electronic combination 

Kaba Mas Corp Cencon Electronic combination 

Kaba Mauer GmbH Variator B - 70076 Mechanical key 

Kaba Mauer GmbH Praetor B - 70079 Mechanical key 

La Gard 1985 Mechanical combination 

La Gard 3332 Mechanical combination 

Notes: 

1. The size P62 Euro Cash Grade 5 safe is a double door free-standing safe with integral depository. 

2. The security grade applies to the safe when both doors are closed, fully locked and the keys removed. 

3. The resistance of the horizontal divider and the deposit mechanism incorporated within that divider to manual forced entry attacks is 

outside the scope of this approval, as is the resistance to fishing and trapping provided by the deposit facility located within that 

divider. 

Lion Steelworks SDN. BHD. 

Lot 4, Solok Waja 3, Kawasan Perindustrian Bukit Raja, 41050 Klang, Selangor, Malaysia 

Tel: +603 3341 3822 • Fax: +603 3342 7630 

E-mail: lion@fmm.jaring.my 



Product Name 

Size 

Security 

Cert. No. 

Reference 

Grade 

N-Series N1, N2 and N3 III 639a/01 


Manufacturer 

S&G6731 

S&G6880 

Model 

Mechanical Combination 

Mechanical Key 

Note: 

1. LPS 1183: Issue 4 is equivalent to BS EN 1143-1:1997 with the exception of the requirement for the locks to meet ENV 1300. 

SMP Security Limited 

Halesfield 24, Telford, Shropshire TF7 4NZ, United Kingdom 

Tel: +44 (0)1952 585673 • Fax: +44 (0)1952 582816 

E-mail: sales@smpsecurity.co.uk • Website: www.smpsecurity.co.uk 



Product Name Size References 1, 2 Security 

Fire Resistance to 

Cert. No. 

Grade 

BS 476: Part 20: 1987 

Community 1414 (39) ED (58) 

1814 (50) ED (74) 

2316 (103) ED (138) 

2916 (130) ED (174) 

3520 (230) ED (297) 

5020 (328) ED (424) 

6020 (393) ED (509) 

Mini-Vault (702) ED (910) 

I 60 115a/01 

20 Nov 2011 257


SAFES 



Cert. No. 

Grade 

BS 476: Part 20: 1987 

1814 (50) ED (74) 

II 60 115a/02 

2316 (103) ED (138) 

2916 (130) ED (174) 

3520 (230) ED (297) 

5020 (328) ED (424) 

6020 (393) ED (509) 

Mini-vault (702) ED (910) 

1814 (50) ED (74) 

III 60 115a/03 

2316 (103) ED (138) 

2916 (130) ED (174) 

3520 (230) ED (297) 

5020 (328) ED (424) 

6020 (393) ED (509) 

Mini-vault (702) ED (910) 

60 50 40 (120) ED (165) 

90 50 40 (180) ED (247) 

90 40 47.5 (171) 

92 42 48.5 (187.4) 

120 50 40 (240) ED (330) 

120 40 47.5 (228) 

122 42 48.5 (248.5) 

150 50 40 (300) ED (412) 

IV - 115a/04 


Lock Type Com munity Safe (LPCB Ref. No. 115a/…) 

1 2 3 4 

Carl Wittkopp GmbH 1819 Mechanical key 


Kaba Mas Corporation SL 523 Electronic combination 


KG Group EM25-20 Electronic combination 


KG Group ML67-40 Mechanical combination 

La Gard 1947 Mechanical combination 



La Gard Combogard 33E Electronic combination 

La Gard Combogard 3740 (Combo Basic) Electronic combination 

La Gard Combogard 6040 (39E) Electronic combination 

La Gard Combogard 66E w ith deadbolt Electronic combination 

La Gard Safeguard 3000/2441 Electronic combination 


Low e and Fletcher 3007 Mechanical key 




Mauer 70076 Mechanical key 






S&G 6730 Mechanical combination 


SMP S520D7-C Mechanical key 


Notes: 

1. ED denotes available with up to 150mm extra depth. 

2. Figures in brackets denote the volumes in litres. The first figure is the standard volume, the second figure is the volume of safe with 

maximum 150mm extra depth. 

258 20 Nov 2011


SAFES 





Cert. No. 

Grade 

BS 476:Part 20: 1987 

Community 1414 (39) ED (58) 

0 60 115b/10 

1814 (50) ED (74) 

2316 (103) ED (138) 

2916 (130) ED (174) 

3520 (230) ED (297) 

5020 (328) ED (424) 

1414 (39) ED (58) 

0 60 115b/11 

1814 (50) ED (74) 

2316 (103) ED (138) 

2916 (130) ED (174) 

3520 (230) ED (297) 

5020 (328) ED (424) 

60 50 40 (120) ED (165) 

90 50 40 (180) ED (247) 

120 50 40 (240) ED (330) 

150 50 40 (300) ED (412) 

V - 115b/05 


Lock Type Com munity Safe 

(LPCB Ref. No. 115b/…) 

5 10 11 











La Gard Combogard 33E Electronic combination 

La Gard Combogard 3740 (Combo Basic) Electronic combination 

La Gard Combogard 6040 (39E) Electronic combination 

La Gard Combogard 66E w ith deadbolt Electronic combination 

















Notes: 

1. ED denote available wit up to 150mm extra depth. 

2. Figures in brackets denote the volumes inlitres. The first figure is the standard volume, the second figure is the volume of safe with 

maximum 150mm extra depth. 

3. LPS 1183: Part 1: Issue 4 is equivalent to BS EN1143-1: 1997, with the exception of the requirements for locks to meet ENV1300. 

20 Nov 2011 259


SECURE SAFE CABINETS 

The Secure safe cabinets listed in this section are approved by LPCB to EN 14450 Secure storage units - 

Requirements, classification and methods of test for resistance to burglary - Secure safe cabinets. 



Tel: +44 (0)1384 239991 • Fax: +44 (0)1384 455129 


Certificate No: 304b to BS EN 14450: 2005 

Secure Safe Cabinets 

Product Name Size Reference Security 

Cert. No. 

Level 

Harlech Lite (Level 1) 00, 0, 1, 2, 3, 4, 5 and 6 S1 304b/01 

Harlech Lite (Level 2) 00, 0, 1, 2, 3, 4, 5 and 6 S2 304b/02 


Model Type Security Cabinet 

(LPCB Ref. No. 304b/..) 

01 02 

Auditcon 52 Electronic Combination 

Caw i 2648 Mechanical Key 



Kaba MAS 552 Electronic Combination 









Mauer President A 71111 Mechanical Key 

Opus 060/EM25.20 Electronic Combination 



Godrej & Boyce Mfg. Co. Ltd. (Security Equipment Division) 

Plant - 17, Pirojshanagar, Vikhroli, Mumbai 400 079, India 

Tel: +91 22 679 64771 • Fax: +91 22 679 61509 

E-mail: securityexports@godrej.com or secure@godrej.com • Website: www.godrej.com 

Certificate No: 954a to BS EN 14450: 2005 

Secure Safe Cabinets 

Product Name Model External External External Weight (kg) Security Level Cert. No. 

Width (mm) Height (mm) Depth (mm) 

Euro-Lite FS10 325 275 325 26 S2 954a/01 

260 20 Nov 2011



Product Name Model External External External Weight (kg) Security Level Cert. No. 

Width (mm) Height (mm) Depth (mm) 

FS40 450 330 380 40 S2 

FS50 360 430 400 41 S2 

FS45 490 470 410 56 S2 

FS65 490 660 410 73 S2 

FS85 490 860 410 91 S2 



Carl Wittkopp GmbH 2648 Mechanical key lock 

Carl Wittkopp GmbH CombiStar 7250 Electronic combination 

Kaba Mas Corporation Auditcon 2 Electronic combination 

Kaba Mas Corporation Auditcon 3100 Electronic combination 

Kaba Mas Corporation SL 525 Electronic combination 

Kaba Mauer GmbH President 71111 Mechanical key lock 

Kaba Mauer GmbH Variator A 70091 Mechanical key 

Kaba Mauer GmbH Variator A 70092 Mechanical key 

KG Group EM25.20 Electronic combination 



La Gard 3330-1 Mechanical combination 

La Gard Combogard 3740 (Combo Basic) Electronic combination 

La Gard Combogard 6040 (39E) Electronic combination 

La Gard Combogard 66E w ith deadbolt Electronic combination 

Steinbach & Vollmann GmbH & Co. Series 4.19.92 Mechanical key lock 

Alternative Brands and Models 

Type Product 

Name 

Model 

Primary Euro-Lite FS10 FS40 FS50 FS45 FS65 FS85 

Alternative 

Guardian S2 FS10 FS40 FS50 FS45 FS65 FS85 

EVVA TR1000 TR4000 TR5000 TR4500 TR6500 TR8500 

do it TR1000 TR4000 TR5000 TR4500 TR6500 TR8500 



Tel: +44 (0)1952 585673 • Fax: +44 (0)1952 582816 


Certificate No: 115c to BS EN 14450: 2005 

Secure Safe Cabinet 

Product Name Model External External External Approx. Security Cert. No. 

Width (mm) Height (mm) Depth (mm) Weight (kg) Level 

Concept 2 1 436 382 382 34 S2 115c/01 

2 536 430 382 43 S2 

3 491 489 482 50 S2 

4 666 489 482 63 S2 

5 816 489 482 75 S2 

6 1010 608 682 125 S2 

7 1372 608 682 162 S2 

Concept 3 1 434 382 394 50 S2 115c/02 

2 534 430 394 62 S2 

3 489 489 494 74 S2 

4 664 489 494 92 S2 

5 814 489 494 110 S2 

20 Nov 2011 261



Product Name Model External 

Width (mm) 

External 

Height (mm) 

External 

Depth (mm) 

Approx. 

Weight (kg) 

Security 

Level 

6 1008 608 694 171 S2 

7 1370 608 694 221 S2 

Cert. No. 


Manufacturer Model Type Product 

Concept 2 Concept 3 




LaGard 3330 Mechanical combination 

LaGard Combogard 33E1 Electronic combination 

LaGard Combogard Basic 3740 Electronic combination 

LaGard Basic Auditgard 66E Electronic combination 

LaGard Combogard Pro 39E Electronic combination 






Note: 

1. No evidence was available to confirm these locks met the minimum lock requirements specified in Table 1 of BS EN 14450: 2005 at 

the time of issuing approval. None the less, the cabinets met all other requirements of BS EN 14450: 2005 and all requirements of 

prEN 14450: June 2004 when fitted with these locks. 

262 20 Nov 2011


AUTOMATIC TELLER MACHINE (ATM) SAFES 

Figures released by the British Bankers’ Association in March 2006 showed that there were 879 physical 

attacks on ATMs in 2005. That is an average of 73 per month. In that year alone, the ATM sector suffered 

pure cash losses of £8,574,210 - equating to an average of £23,000 per day. 

This represented a sharp rise in losses through ATM crime compared with previous years. Since then theft of 

ATM safes or money from ATM safes has not abated reinforcing the need for ATM estate mangers to ensure 

their ATM safes meet appropriate security standards. 

By selecting ATMs that incorporate a safe graded to LPS 1183 or EN 1143-1, ATM losses can be significantly 

reduced due to the increased time and effort required to overcome the mounting system and gain entry to the 

contents of the safe itself. 

As with free-standing safes and strongrooms, the locks fitted to the ATM safe and construction of the safe are 

critical. Specifiers and users should therefore discuss any proposals with their insurance company and the 

safe manufacturer prior to undertaking such work. 

Please note that the fixing system employed forms part of the over all classification assessment. As such, the 

use of alternative fixings or anchor systems, while generally well intentioned, may undermine the security 

afforded by the ATM safe and invalidate the approval. It is also important to check locking mechanisms 

regularly to ensure they have not been tampered with. 

The same rigorous approval procedures and conditions are applied to the ATM safes listed in this section as 

are applied to free standing safes, strongrooms and deposit safes. 

20 Nov 2011 263


ANTI-BANDIT ATM SECURITY DEVICES 

A number of ATMs have been attacked while being replenished as this is when there is the most cash held 

within the ATM and the cash cassettes are the most vulnerable because the door to the ATM safe is open. 

Products listed in this section are designed to prevent the unauthorised removal of cash cassettes from the 

ATM safe when the ATM safe door is open. 

These products have been approved to LPS 1175 Requirements and testing procedures for the LPCB 

approval and listing of intruder resistant building components, strongpoints, security enclosures and free 

standing barriers. 

LPS 1175 is based on manual attack testing and currently defines eight levels of resistance to entry. 

These are measured in terms of attack tools and time available to the attacker. This enables specifiers to 

select products according to the risks that they and their property face. 

Due to the intended application of these products, the entry criteria used to assess these products in 

accordance with clause 4.3 of LPS 1175 is defined in the notes relating to each of the products listed. 

Although the evaluation and approval covers attempts to remove the products from the ATM safes to which 

they are fitted, they do not cover the attack resistance of those ATM safes. 

Pressex UK Limited 

Kingsway South, Team Valley, Gateshead, Tyne & Wear NE11 0SH, United Kingdom 

Tel: +44 (0)191 497 3430 • Fax: +44 (0)191 497 3431 

E-mail: pressex@responsive-engineering.com • Website: www.responsive-engineering.com 


Anti-Bandit ATM Security Device 

Product Name Compatible ATMs Security Cert. No. 

Rating 

Lockpoint ATM Duress Guard NCR 84 ATM incorporating an NCR 5884 

UL291 ATM safe 

NCR 87 ATM incorporating an NCR 5887 

UL291 ATM safe 

3 870a 

Notes: 

1. The Lockpoint ATM Duress Guard permits access to individual cash cassettes within the ATMs listed above once the door to the ATM 

safe has been opened. This is possible without the need for the operator to remember an access code or use a coded key, token or 

other such device to operate the doors on the Lockpoint ATM Duress Guard. 

2. The Lockpoint ATM Duress Guard prevents removal of individual cash cassettes from within the ATMs via the aperture created when 

the door to the ATM safe is opened. The level of protection against unauthorised removal of the replenished cash cassettes is 

expressed in the above table as a Security Rating in accordance with the requirements of LPS1175: Issue 6. The Security Rating is 

achieved by the Lockpoint ATM Duress Guard for up to 60 minutes after the door(s) to the compartments in which the replenished 

cassettes are located. This is providing the doors to the adjacent compartments have also been operated to activate the locking 

system on those doors. The Lockpoint ATM Duress Guard provides protection to individual replenished cash cassettes while those in 

adjacent compartments are being replenished at least compatible with the requirements of Security Rating 1. 

3. The product’s resistance to electronic and digital attack methods, other than those possible with tools defined in LPS 1175: Issue 6 1 

for the Security Ratings achieved, are outside the scope of this approval. 

4. This approval does not cover the attack resistance of the ATM into which the Lockpoint ATM Duress Guard is fitted. However, the 

approval does cover the resistance to unauthorised removal of the Lockpoint ATM Duress Guard from the ATM via the aperture 

created when the door to the ATM safe is opened. 

264 20 Nov 2011


DEPOSIT SAFES 

Safes that incorporate a deposit facility are covered by EN 1143-2 Requirements, classification and methods 

of test for resistance to burglary - Part 2: Deposit systems. This describes tests over and above those 

specified in EN 1143-1, and includes ‘forcing’, ‘fishing’, ‘trapping’ and ‘deposit retrieval’. 

Deposit safes take a number of forms and these affect the classification attributed to them. 

Deposit safes are normally located within a building and are primarily designed to enable employees to 

deposit money or other items without having to open the main door of the safe. Deposit safes receive a 

classification of “D-#” where # is the grade of resistance achieved during testing. 

Deposit safes range from standard deposit safes with manual operation through to the distributed deposit 

systems employed by supermarkets. 

Night safes, on the other hand, are often accessible from the street and are primarily used by financial 

institutions for providing a secure depositing system for their customers. Night safes receive a classification of 

“N-#” where # is the grade of resistance achieved during testing. 

20 Nov 2011 265


STRONGROOMS 

Strongrooms listed in this section are approved by LPCB to one or more of the following standards: 

 

 

EN 1143-1 Secure storage units. Requirements, classification and methods of test for resistance to 

burglary. Safes, strongroom doors and strongrooms. 

LPS 1183 Specification for safe storage units. Part 1: Safes and strongrooms 

Copies of LPS 1183 can be downloaded free of charge from our website www.RedBookLive.com. 

Strongrooms take two forms: 

 

 

Cast in-situ. The strongroom structure is cast on site where there is insufficient access to manoeuvre 

prefabricated panels into place. 

Pre-fabricated. The strongroom is formed on site from pre-fabricated panels, designed to bolt together 

securely to form the desired configuration. 

Strongrooms are not only designed to secure larger volumes of cash and jewellery but are increasingly used 

to store items such as artwork and antiquities, pharmaceuticals, military equipment and highly sensitive 

documentation. Strongrooms are also increasingly being used to protect large scale IT server hubs due to the 

high value of the server equipment and business continuity risks associated with the potential loss of such 

equipment or data. 

It is important to ensure that all exposed fixings, jointing plates, the substrate into which the device is fitted 

and the locking mechanisms are regularly checked to ensure that they are in good condition and that they 

have not been tampered with. 

It is also important to ensure only those design options listed, such as special cable access or ventilation 

panels, are incorporated within the strongroom construction as the use of alternative options may undermine 

the level of security provided by the strongroom. 

Explosion (EX) Designation 

This designation indicates a product offers resistance to detonation of a PETN (Pentaerythritol tetranitrate) 

explosive charge followed by post detonation tool attacks aimed at achieving entry to the strongroom. Where 

the use of explosive charges is perceived to be a threat it is recommended products with this designation are 

selected. 

Core Drill (CD) Designation 

This designation is only applicable to strongrooms and strongroom doors achieving grades V and above. This 

designation reflects the ability of a product to pass the diamond drill test specified within EN 1143-1 which is 

designed to demonstrate the product’s superior resistance to methods of forced entry that solely involve the 

use of diamond core drills. 

266 20 Nov 2011


SECURE OFFICE FURNITURE 

Office furniture and other equipment designed to prevent unauthorised access to confidential and valuable 

documents are tested and certified to LPS 1228 Specification for testing and classifying the burglary 

resistance of office furniture. The standard was developed for the Cabinet Office as a means of specifying and 

testing the resistance offered by office furniture and document cabinets to unauthorised access. 

The standard specifies four levels of protection based on the availability of tools and time to the attacker. This 

enables specifiers to select the equipment that best suits their needs, such as a filing cabinet, cupboard or 

document safe, whilst knowing that the equipment will provide the required level of protection against 

unauthorised access, whether in a domestic, commercial or Government environment. 

The burglary resistance of the complete product is tested, including any in-situ hardware such as locks and 

hinges. However, no allowance is made for various stages of locking. The locks assessed as part of the 

evaluation of the product are listed under the ‘compatible locks’ section of each company’s entry. 

It is important that specifiers only select products covered by the scope detailed on the certificate as the 

performance of products that fall outside the scope of the assessment may not be adequate. It is also 

important to ensure that the products are installed in accordance with the manufacturer’s instructions and that 

all exposed fixings, the substrate into which the device is fitted and the locking mechanisms are regularly 

checked to ensure that they are in good condition and that they have not been tampered with. This will ensure 

that criminals cannot simply remove the security device to a remote location in order to gain access to the 

protected documentation or equipment. 

20 Nov 2011 267


SECURE ENCLOSURES 

Security enclosures that have been assessed to LPS 1175 Specification for testing and Classifying the 

Burglary Resistance of Building Components, Strongpoints and Security Enclosures are listed in this section. 

Each security rating is appropriate to the level of risk to forced entry or removal, and covers everything from 

the secure storage of tools in the domestic environment, to protection of remote equipment on railway and 

telecommunications infrastructures. Some examples of applications include: secure site tool and plant storage 

units, portable office buildings and shipping containers. 

The use of appropriately rated and installed physical security enclosures will protect the contents of the 

enclosure from the unwanted attentions of the opportunist or professional criminal. 

LPS 1175 is based on manual attack testing and currently defines eight levels of resistance to entry into the 

enclosure or removal of the enclosure from the supporting substrate. The ratings are determined in terms of 

attack tools and time available to the attacker, and enables specifiers to select products according to the risks 

that they and their property face. Unless otherwise stated, entry into the enclosures listed was determined 

according to the ability to pass the 400 mm by 225 mm elliptical test block defined in LPS 1175. This is 

considered to be a size through which a person may pass. In some cases alternative failure criteria was used 

during the evaluation of the enclosures listed. These were designed to suit the intended application of the 

enclosures concerned and the failure criteria used is noted in the relevant product entries. 

It is important to ensure that the enclosures are installed in accordance with the manufacturers instructions 

and that all exposed fixings, the substrate onto which the enclosure is fitted, and the locking mechanisms are 

regularly checked to ensure that they are in good condition and that they have not been tampered with. 

Details regarding the rating system can be found in the standard itself, copies of which are available free of 

charge and can be downloaded from the LPCB web site www.RedBookLive.com. 

It is recommended that assets such as cash or jewellery should preferably be stored in safe storage units or 

strongrooms approved by LPCB. These are listed in Section 2. Those looking to prevent unauthorised 

removal of computer equipment consider using the physical protection devices listed in Section 12. 

Asgard Secure Steel Storage (a trading division of Flexiform Business Furniture 

Limited) 

1392 Leeds Road, Bradford BD3 7AE, United Kingdom 

Tel: +44 (0)1274 706206 • Fax: +44 (0)1274 706247 


Security Enclosures 

Product Name 

Nominal Enclosure Nominal Enclosure Nominal Enclosure Security Cert. No. 

Height (m) 

Width (m) 

Depth (m) Rating 

Asgard Classic Secure Unit 1.9 1.9 0.8 1 596a/01 

Asgard Compact Secure Unit 1.9 1.1 0.8 1 596a/02 

Asgard Universal 0.7 0.6 0.5 1 596a/03 

Asgard Annexe 1.5 1.8 0.9 1 596a/04 


Lock Type LPCB Ref. No 596a/.. 

Winlock 

HS2000 

Accessories 

Garage door locking system fitted w ith Euro Profile 

1850/05/30 single cylinder 

1 2 3 4 

 

268 20 Nov 2011



Accessory 

Tool Rail 

Adjustable Shelf 

LPCB Ref. No 596a/.. 

1 2 3 4 

 

Notes: 

1. In order to prevent complete removal of the secure units, they must be affixed to concrete foundations in accordance with the self 

assembly instructions supplied with the units. 

2. On products with sloping or peaked roof design, the height given is the maximum. 

Bastion Security Installations Limited 

Finlay Court, Simonside East Industrial Estate, South Shields, Tyne and Wear NE34 9QA, United Kingdom 

Tel: +44 (0)191 419 3777 • Fax: +44 (0)191 497 2997 

E-mail: moreinfoplease@bastionprotects.com • Website: www.bastionprotects.com 


Expandable Security Enclosure 

Product 

Name 

Type 

Height 

(m) 

Bastion 

Enclosure 

Expanding security 

enclosure 1 with integral 

entrance doorset 

Width 

(m) 

Length When 

Enclosure Is Fully 

Expanded (m) 

Length When 

Enclosure Is 

Contracted (m) 

Security 

Rating 

Cert. No. 

2.469 1.700 2.655 1.700 5 2 1046a/01 

3 

Manufacturer Model Type Operating Devices Compatible 

Compatible Doorset Locking System 

Internal Face External Face 

Cylinders 

Tindall Engineering 

Limited 

Mico Evo AD3 w ith 

USCH 5 

Three point lock w ith integrated 

automatic deadlock and USCH 5 

cylinder guard 

Key and lever 

handle 

Key and lever 

handle 

A 

4 

Manufacturer Model Type Operating Devices Compatible 

Compatible Corridor Locking System 

Internal Face External Face 

Cylinders 

ASSA 766 Roller Bolt Tw o deadlocks 5 None Key A 

Compatible Cylinders 

Ref. Manufacturer Model Type 

A Access2 Tigris Omega Scandinavian Oval 

Notes: 

1. The enclosure may be used to house ATM’s. The resistance of ATM’s used within the enclosure is outside the scope of approval. It is 

the manufacturers’, and other clients’, responsibility to ensure the ATM and the aperture within which it is located cannot be exploited 

in order to gain entry into the enclosure. 

2. The enclosure achieves a Security Rating 5 classification in the optimum locked condition, i.e. when placed in the contracted (i.e. 

unexpanded) position, the staples are secured with the two locks listed in the ‘compatible corridor locking systems’ table and the lock 

on the doorset is secured. A Security Rating 3 classification prevails in the minimum locked condition, i.e. the enclosure is expanded 

and the lock on the doorset is secured. 

3. This lock secures the integral doorset. 

4. These locks secure the enclosure into the contracted (i.e. unexpanded) position. 

5. The external face of the cylinder is protected by a USCH 3 cylinder guard supplied by Tindall Engineering Limited. 

6. The approval covers the enclosures when installed onto concrete bases of equivalent resistance to attack, using the method of 

installation defined on the ‘Installation Instructions’ drawing (Revision A, dated 3 August 2011). 

20 Nov 2011 269





Tel: +44 (0)191 258 5052 • Fax: +44 (0)191 259 5742 



Modular Security Enclosure System 

Product 

Name 

Product 

Type 

Minimum 

Height 

(m) 

Maximum 

Height (m) 

Securiclad Enclosure 

with 

horizontal 

laid panels 

Enclosure 

with 

vertically 

laid panels 

Enclosure 

with 

horizontal 

laid panels 

Enclosure 

with 

vertically 

laid panels 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Depth (m) 

Maximum 

Depth (m) 

Security 

Rating 

Cert. 

No. 

2.5 Unlimited 2.5 Unlimited 2.5 Unlimited 3 142c/01 

2.5 6.0 0.25 Unlimited 0.25 Unlimited 3 

2.5 Unlimited 2.5 Unlimited 2.5 Unlimited 4 142c/02 

2.5 6.0 0.25 Unlimited 0.25 Unlimited 4 

System Components 

Component Type 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Thickness 

(m) 

SR3/SR4 panel (mineral w ool) 0.25 1.19 2.5 6 0.1 

Ceiling panel (mineral w ool) 0.25 1.19 1 6 0.1 

SR3/SR4 panel (PIR) 0.25 1.19 2.5 6 0.1 

Ceiling panel (PIR) 0.25 1.19 1 6 0.1 

Products Compatible with the Securiclad Security Panel System 2,3 

270 20 Nov 2011

Manufacturer Product Name Product Type LPCB 

Certificate 

Number 


Benw eldSecure 

Pow ershield Doors 

Limited 

Selectaglaze Limited 

Professional Barriers 

Limited 


Pow ershield Doors 

Limited 

Centurion A363S Single leaf 

outw ard 

opening 

doorset 

Centurion A363D Double leaf 

outw ard 

opening 

doorset 

Bew dley doorset Single leaf 

outw ard 

opening 

doorset 

Pow ershield 

Class 3 single 

Pow ershield 

Class 3 double 

Series 55’ level 

3’ 

Single leaf 

outw ard 

opening 

doorset 

Double leaf 

outw ard 

opening 

doorset 

Fixed light 

security 

w indow 

Security 

Rating 

131d/04 3 12, 13, 15, 

16, 18 and 

19 

131d/05 3 12, 13, 15, 

16, 18 and 

19 



Compatible Locking 

Systems 

Active Leaf Passive 

Leaf 

N/A 

34, 35 and 

36 

746a/01 3 1 N/A 

852a/01 3 2 to 11, 

13,16,17 and 

19 

852a/02 3 2 to 11, 

13,16,17 and 

19 

N/A 

32 

683a/06 3 N/A N/A 

Extendor Eclipse Collapsible grille 869a/01 3 33 N/A 

Centurion A355 Single leaf 

outw ard 

opening 

doorset 

Centurion A364S Single leaf 

outw ard 

opening 

doorset 

Centurion A364D Double leaf 

outw ard 

opening 

doorset 

Pow ershield 

Class 4 single 

Single leaf 

outw ard 

opening 

doorset 

131d/01 4 13 N/A 

131d/02 4 13, 16, 19, 

27, 29 and 

31 

131d/03 4 13, 16, 19, 

27, 29 and 

31 

852a/03 4 3, 5, 7, 9, 10, 

13, 16, 19, 

20, 21, 22, 

23, 24, 26, 

28 and 30 

N/A 

34, 35 and 

36 

N/A 

Pow ershield 

Class 4 double 

Double leaf 

outw ard 

opening 

doorset 

852a/04 4 3, 5, 7, 9, 10, 

13, 16, 19, 

20, 21, 22, 

23, 24, 26, 

28 and 30 

32 

Compatible Locking Systems for Products Compatible with the Securiclad Security Panel System 

20 Nov 2011 271



Com patible 

Locking 

Systems 

1 Assa 9787 Single point mortice 

hook lock 

2 MICO 942-3L 

EPC INT AD / 

HSCH 3 

3 MICO 942-3L 

EPC INT AD 

Model Type Operation 

3-w ay locking system 

w ith automatic 

deadlocking 



deadlocking 

4 MICO 942-3 EPC 3-w ay locking system 

INT MD / HSCH 3 w ith manual deadlock 

5 MICO 942-3 EPC 

INT MD 

6 MICO 942-3P 

EPC INT MD / 

HSCH 3 

7 MICO 942-3P 

EPC INT MD 

8 MICO 942-3L 

EPC INT MD / 

HSCH 3 

9 MICO 942-3L 

EPC INT MD 

10 MICO 942-3L INT 

AD 


w ith manual deadlock 











deadlocking 

Key 

Entry 

Europrofile 

cylinder w ithin 

the HSCH 3 


and lever handle 

None 

Europrofile 


the HSCH 3 



None 

Europrofile 


the HSCH 3 



None 

Europrofile 


the HSCH 3 



None 

None 

Exit 

Key via an Assa 

256 (Assa 

Classic) 

combined 

cylinder ring and 

thumbturn 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Europrofile 

cylinder 

(key:key)and 

lever handle 

Europrofile 

cylinder 

(key:key) and 

panic exit push 

plate 

Europrofile 

cylinder 

(key:key) and 


plate 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Scandinavian 

oval cylinder and 

lever handle 

Compatible 

Cylinders 

Q or R 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 

- 

- 

11 MICO 942-3 INT 

MD / HSCH 3 



Scandinavian 

oval cylinder 

Scandinavian 

oval cylinder 

G, H, I, J, K, L, 

M, N or P 

12 

w ithin the HSCH and panic exit 

3 cylinder guard push plate 


G 

272 20 Nov 2011

13 MICO 942-3 INT 

MD 

16 MICO 942-3P INT 

MD 





None 

None 

Scandinavian 

oval cylinder 

and panic exit 

push plate 

Scandinavian 

oval cylinder 

and push pad 

14 MICO 942-3P INT 3-w ay locking system Scandinavian 

G, H, I, J, K, L, 

MD / HSCH 3 w ith manual deadlock oval cylinder 

M, N or P 

w ithin the HSCH 

15 

3 cylinder guard 

G 


Scandinavian 

oval cylinder 

and push pad 

Scandinavian 

oval cylinder 


17 MICO 942-3L INT 3-w ay locking system Scandinavian 

G, H, I, J, K, L, 

MD / HSCH 3 w ith manual deadlock oval cylinder 

M, N or P 


18 


G 


19 MICO 942-3L INT 

MD 

20 MICO 942-3L 

EPC INT AD / 

HSCH 4 





deadlocking 

21 MICO 942-3 EPC 3-w ay locking system 

INT MD / HSCH 4 w ith manual deadlock 

22 MICO 942-3P 

EPC INT MD / 

HSCH 4 

23 MICO 942-3L 

EPC INT MD / 

HSCH 4 





None 

Europrofile 


the HSCH 4 



Europrofile 


the HSCH 4 



Europrofile 


the HSCH 4 



Europrofile 


the HSCH 4 



Scandinavian 

oval cylinder 


Europrofile 

cylinder 

(key:key) and 

lever handle 

Europrofile 

cylinder 

(key:key) and 


plate 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

lever handle 



- 

- 

- 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

20 Nov 2011 273



24 MICO 942-3L INT 3-w ay locking system Scandinavian Scandinavian G, H, I, J, K, L, 

AD / HSCH 4 w ith automatic oval cylinder oval cylinder M, N or P 

25 

deadlocking 

w ithin the HSCH and lever handle 


G 


26 MICO 942-3 INT 

MD / HSCH 4 



Scandinavian 

oval cylinder 

Scandinavian 

oval cylinder 

G, H, I, J, K, L, 

M, N or P 

27 

w ithin the HSCH and panic exit 


G 


28 MICO 942-3P INT 3-w ay locking system Scandinavian Scandinavian G, H, I, J, K, L, 

MD / HSCH 4 w ith manual deadlock oval cylinder oval cylinder M, N or P 

29 

w ithin the HSCH and push pad 


G 


30 MICO 942-3L INT 3-w ay locking system Scandinavian Scandinavian G, H, I, J, K, L, 

MD / HSCH 4 w ith manual deadlock oval cylinder oval cylinder M, N or P 

31 

w ithin the HSCH and lever handle 


G 


32 M0455 Surface mounted 

barrel bolts 

33 Extendor Eclipse 

CL03 w ith CL03 


- Europrofile 


the CL03 cylinder 

guard 

- - - 

Key (w hen 

internal locking 

version only) 

S, T or U 

34 MICO 942 2-w ay panic exit - Panic bar - 

device 

35 MICO 942P 2-w ay emergency exit - Push pad - 

device 

36 MICO 942L 2-w ay emergency exit - Lever handle - 

device 

Compatible Cylinders for Products Compatible with the Securiclad Security Panel System 

Cylinder Manufacturer Model Type 

Reference 

A Abloy Protec CY304 Double Europrofile cylinder (key:key) 

B Abloy Disclock Pro CY304 Double Europrofile cylinder (key:key) 

C ASSA Tw in 7622 Double Europrofile cylinder (key:key) 

D ASSA C5822 Double Europrofile cylinder (key:key) 

E ASSA 4822 Double Europrofile cylinder (key:key) 

F Kaba Quattro S Euro Double Europrofile cylinder (key:key) 

G ASSA 4807 Half Scandinavian oval mechanical cylinder 

H ASSA Tw in 7607 Half Scandinavian oval mechanical cylinder 

I ASSA C5807 Half Scandinavian oval mechanical cylinder 

J ASSA 4407 Half Scandinavian oval mechanical cylinder 

K Abloy Protec CY201PT Half Scandinavian oval mechanical cylinder 

L Locken CL-PL2WR Half Scandinavian oval mechatronic cylinder 

M Kaba Quattro S Oval Half Scandinavian oval mechanical cylinder 

N Kaba K20 Oval Half Scandinavian oval mechanical cylinder 

O Abloy Disclock Pro CY201DP Half Scandinavian oval mechanical cylinder 

P ASSA 4801 Half Scandinavian oval mechanical cylinder 

Q ASSA C5801 Half Scandinavian oval mechanical cylinder 

R ASSA C5803 Half Scandinavian oval mechanical cylinder 

S ASSA dp4400 Single Europrofile cylinder (key) 

T CISA AP3S Single Europrofile cylinder (key) 

U Kaba Quattro Plus Single Europrofile cylinder (key) 

274 20 Nov 2011



Notes: 

1. The Securiclad panel systems must be installed in accordance with the approved Securiclad design manual (ISO/SECG04/02/11) and 

compatible product list (ISO/SEC/DSP/15/9/10). 

2. The Security Rating attributed to the compatible product must be at least that of the enclosure in which it is to be fitted. For example, 

a Security Rating 3 doorset shall not be used to form part of a Security Rating 4 enclosure. 

3. Refer to notes contained within the relevant certificate/Red Book entries for these products for details of restrictions on their use. 

Liddle Doors Limited 

Wagonway Road Industrial Estate, Hebburn, Tyne and Wear NE31 1SP, United Kingdom 

Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 

E-mail: liddle@liddledoors.co.uk • Website: www.liddledoors.co.uk 

Certificate No: 442e to LPS 1175: Issue 6 

Security Cabinet (Wall Mounted) 

Product Name Model Nominal Cabinet 

Height (mm) 

Nominal Cabinet 

Width (mm) 

Nominal Cabinet 

Depth (mm) 

Security 

Rating 

Cert. 

No. 

Liddle Series 2 Size 1 wall mounted 400 460 240 2 442e/01 

Security Box security cabinet 

Size 2 wall mounted 400 400 150 2 

Liddle Series 3 

Security Box 

security cabinet 

Size 1 wall mounted 


Size 2 wall mounted 


400 460 240 3 442e/02 

400 400 150 3 

Compatible Padlocks 

Padlock Designation Cylinder LPCB Ref. No 442e/ 

1 2 

Abloy PL340/25 Abloy Disklock Pro 

Notes: 

1. The security boxes are approved when wall mounted directly to brickwork, concrete or steel. The approval does not cover the security 

boxes when mounted to alternative substrates or via intermediate substrates such as plasterboard. 

2. Certification does not cover the use of padlocks other than those listed above. Utilisation of unlisted padlocks may affect the level of 

security offered by the product. 

Lowrey Contractors Limited 

200 South Liberty Lane, Ashton Vale Trading Estate, Ashton Vale, Bristol BS3 2TW, United Kingdom 

Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 

E-mail: lowrey@talk21.com • Website: www.lowrey-contractors.co.uk 


Modular Security Cage System 

Product 

Name 

Type Minimum 

Height 

(m) 

Lowrey Level 

1 Security 

Mesh Panel 

System 

Lowrey Level 

2 Security 

Mesh Panel 

System 

Cage 

formed from 

four sides 

and a ceiling 

Cage 

formed from 

four sides 

and a ceiling 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 1 

Maximum 

Width (m) 

Minimum 

Depth 

(m) 

Maximum 

Depth 

(m) 

Security 

Rating 

Cert. 

No. 

1.1 3.91 0.5 Unlimited 0.5 4.0 1 974b/01 

1.1 3.91 0.5 Unlimited 0.5 4.0 2 974b/02 

20 Nov 2011 275



Product 

Name 

Lowrey Level 

3 Security 

Mesh Panel 

System 

Type 

Cage 

formed from 

four sides 

and a ceiling 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 1 

Maximum 

Width (m) 

Minimum 

Depth 

(m) 

Maximum 

Depth 

(m) 

Security 

Rating 

Cert. 

No. 

1.1 3.91 0.5 Unlimited 0.5 4.0 3 974b/03 


Component Type Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Mesh w all panel 0.25 2.4 0.5 1.5 N/A N/A 

Roof panel Mesh roof panel N/A N/A 0.25 1.5 0.25 3.8 

Support post 

Corner post 

Doorsets 

Support post for 1.0 3.8 0.215 0.215 N/A N/A 

w alling system 

270 degree corner 1.1 3.91 0.125 0.125 N/A N/A 

post for w alling 

system 

90 degree corner 1.1 3.91 0.11 0.11 N/A N/A 


system 

Single leaf outw ard 

opening doorset 

Refer to ‘Low rey Level 1, 2 and 3’ single leaf mesh security doorsets (LPCB 

Ref. No. 974a/01, 03 and 05) for scope of approval. 

Double leaf outw ard Refer to ‘Low rey Level 1, 2 and 3’ double leaf mesh security doorsets (LPCB 

opening doorset Ref. No. 974a/02, 04 and 06) for scope of approval. 

Notes: 

1. The minimum width of an enclosure wall incorporating a doorset is 0.63 m. 

2. The cage’s resistance relies on the supporting substrate offering compatible resistance to manual attack. 

3. The Lowrey security mesh panel system is approved when installed in accordance with the instructions detailed on Lowrey’s 

document E-INST001 (Issue 3). 


Modular Security Enclosure System 

Product 

Name 

Product 

Type 

Minimum 

Height 

(m) 

Maximum 

Height (m) 

Lowrey 

Level 4 

Security 

Solid 

Panel 

System 

Enclosure 

formed from 

four sides 

and a 

ceiling 

Minimum 

Width 

(m) 1 

Maximum 

Width (m) 

Minimum 

Depth (m) 

Maximum 

Depth (m) 

Security 

Rating 

Cert. 

No. 

1.1 3.91 0.5 Unlimited 0.5 4.0 4 974e/01 


276 20 Nov 2011


Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 



Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Solid w all panel 0.25 2.4 0.5 1.5 N/A N/A 

Roof panel Solid roof panel N/A N/A 0.25 1.5 0.25 3.8 

Support post 

Corner post 

Doorsets 

Support post for 


270 degree 

corner post for 


90 degree corner 


system 

Single leaf 

outw ard opening 

plain leaf doorset 

Double leaf 



1.0 3.8 0.215 0.215 N/A N/A 

1.1 3.91 0.125 0.125 N/A N/A 

1.1 3.91 0.11 0.11 N/A N/A 

Refer to ‘Low rey Level 4’ single leaf security doorsets (LPCB Ref. No. 

974d/01) for scope of approval. 

Refer to ‘Low rey Level 4’ double leaf security doorsets (LPCB Ref. No. 


Notes: 

1. The minimum width of an enclosure wall incorporating a doorset is 0.63 m. 

2. The enclosures resistance relies on the supporting substrate offering compatible resistance to manual attack. 

3. The Lowrey security solid panel system is approved when installed in accordance with the instructions detailed on Lowrey’s document 

E-INST001 (Issue 3). 

Morgan Marine Limited 

Llandybie, Ammanford, Carmarthenshire SA18 3GY, United Kingdom 

Tel: +44 (0)1269 850437 • Fax: +44 (0)1269 850656 

E-mail: sales@morgan-marine.com • Website: www.morgan-marine.com 



Product 

Name 

Product 

Type 

Nominal 

Minimum 

Height 1 

(m) 

Morgan 

Titan 

SR2 

Morgan 

Titan 

SR3 

GRP 

security 

enclosure 

GRP 

security 

enclosure 

Nominal 

Maximum 

Height 1 

(m) 

Nominal 

Minimum 

External 

Width (m) 

Nominal 

Maximum 

External 

Width (m) 

Nominal 

Minimum 

External 

Length 

(m) 

Nominal 

Maximum 

External 

Length (m) 

Security 

Rating 

Cert. No. 

2.21 5.0 1.0 2 14.0 1.0 2 30.0 2 1051a/01 

2.21 5.0 1.0 2 14.0 1.0 2 30.0 3 3 1051a/02 

Compatible Doorsets 

Manufacturer Model Type Structural 

Opening 

Structural 

Opening 


Systems 

LPCB Ref. 

No. 

Height (m ) Width (m) Active 

Leaf 

Passive 

Leaf 

PSF Wales Hercules Single leaf outw ard 2.12 1.12 1 and 2 N/A 953a/01 

Limited SAF3 opening hinged doorset 

PSF Wales 

Limited 

Hercules 

SAF3 

Double leaf outw ard 

opening hinged doorset 

2.21 2.21 1 and 2 3 953a/02 

Locking Options Available on the Compatible Doorsets 

20 Nov 2011 277



Com patible 

Locking 

System 

1 Tindall 

Engineering 

2 Tindall 

Engineering 

3 Commercial 

Body Fittings 

Limited 

Cylinders Options 

Manufacturer Model / Type Operation Compatible 

Cylinders 

Entry 

Exit 

Mico 942-3L INT AD / USCH4 

three-point auto-deadlocking autobolting 

system w ith external 

cylinder access 

Mico 942-3L INT MD / USCH4 

three-point manual-deadlocking 

auto-bolting system w ith external 

cylinder access 

USCH4 cylinder 

guard incorporating 

a Scandinavian oval 

cylinder 


guard incorporating 

a Scandinavian oval 

cylinder 

Thumbturn and 

lever handle 

Thumbturn and 

lever handle 

Sprung tow er bolt - Tw o sprung tow er 

bolts 3 


Reference 

A Abloy Disclock Pro CY201DP Mechanical Scandinavian oval cylinder 

B Assa 4807 Mechanical Scandinavian oval cylinder 

C Assa C5807 Mechanical Scandinavian oval cylinder 

D Assa Tw in 7607 Mechanical Scandinavian oval cylinder 

E Kaba K20 Oval Mechanical Scandinavian oval cylinder 

F Kaba Quattro S Oval Mechanical Scandinavian oval cylinder 

G Locken CL-PL2WR Mechatronic Scandinavian oval cylinder 4 

A to G 

A to G 

N/A 

Approved Optional Design Features 

Optional Design Feature 

Reference Revision / 

Date 

Removable roof MDS017 C 

22/7/11 

Shrouded vents w ith cow ls measuring 0.45 m w ide by 0.45 m high by 0.45 m deep 5,6 

Associated Drawing 

MDS015 

(Sheet 2) 

F 

22/7/11 

Notes: 

1. The height is measured from the ground to the underside of the roof panel. 

2. This is the minimum length/width of the enclosure when the enclosure does not incorporate a doorset in that plane. The minimum 

length/width of the enclosure when it incorporates a doorset within that plane is 1.39 m (single leaf doorset fitted) or 2.39 m (double 

leaf doorset fitted). 

3. The Morgan Titan SR3 enclosures incorporating double leaf doorsets achieve Security Rating 3 when both sprung tower bolts on the 

passive leaf are engaged and the lock mechanism fitted to the primary leaf is engaged and deadlocked. A Security Rating 1 

classification prevails if one of the sprung tower bolts on the passive leaf is not engaged. 

4. The resistance of the electronic cylinder to ‘non-mechanical’ attack is outside the scope of this approval because it is outside the 

scope of LPS1175: Issue 7. Likewise, this approval does not cover the possible effects of any susceptibilities relating to the 

functionality and performance of the keys that may be used to operate the cylinder. It is therefore recommended that specifiers and 

installers satisfy themselves that the components used are either resistant to mechanical and other forms of tampering/abuse and are 

resistant to any environmental conditions/interference that may cause the lock to disengage. 

5. The approval does not cover the provision of any other apertures within the fabric of the enclosure, e.g. for ventilation or other 

services, other than that provided by the shrouded vent listed in the list of approved optional design features. 

6. The shrouded vents must be located at least 0.3 m away from the thumbturns and lever handles present on Hercules SAF3 doorsets 

when fitted within the same plane as the doorset, and 0.4 m away from the thumbturns and lever handles present on Hercules SAF3 

doorsets when located in a wall that is perpendicular to the plane of the doorset. 

7. The approval covers the enclosures when installed onto stepped concrete bases of equivalent resistance to attack, using the method 

of installation defined on drawing MDS 015 (Revision F dated 22 July 2011). 

278 20 Nov 2011



Professional Barrier Systems Limited 

16 Stapledon Road, Orton Southgate, Peterborough PE2 6TD, United Kingdom 

Tel: +44 (0)1733 361511 • Fax: +44 (0)1733 361512 

E-mail: mail@extendor.co.uk • Website: www.extendor.co.uk 


Modular Security Cages 

Product 

Name 

Type Minimum 

Height 

(m) 

Extendor 

Eclipse 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Modular 

cage formed 

from 

Extendor 

Eclipse fixed 

and opening 

grilles 1 0.715 3.67 3, 4 0.48 Unlimited 2, 

5 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

1.0 Unlimited 2, 

5 

Security 

Rating 

Cert. 

No. 

3 869b/01 



Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel 4 0.625 3.58 0.3 3.06 N/A N/A 

Roof panel N/A N/A 0.3 3.06 0.625 3 

Doorset 7 0.625 2.7 1 3.025 N/A N/A 

Notes: 

1. Cages are rectilinear in plan and not limited to a simple rectangle. That is approval covers cages with acute and obtuse vertical 

corners. 

2. The maximum sizes of the cage are subject to specific assessment of physical restrictions and operational conditions. 

3. The maximum height of any opening sash within the cage is 2.7 m. Cages above this height incorporate a fixed grille. 

4. Wall panels can be coupled vertically to form cage height. 

5. The maximum clear span is 4 m. Spans greater than this require support column(s). 

6. For details of locking options and accessories approved refer to certificate 869a/01. 

7. The certification covers the installation of the cage directly to a concrete floor 8 . 

8. The cages can also be secured onto raised floors. This is providing the cage extends under the raised floor to a concrete floor 

beneath it. The wall panels located under the raised floor shall be bolted to the underside of the wall panels located above the floor, 

sandwiching the floor panels between them. The wall panels located under the raised floor shall also be directly fixed to the concrete 

floor beneath the cage. 

PSF Wales Limited 

Llys Rhiannon, Cil Yr Ychen Industrial Estate, Landeilo Road, Llandybie, Ammanford, Carmarthenshire SA18 

3GY, United Kingdom 

Tel: +44 (0)1269 851777 • Fax: +44 (0)1269 851747 

E-mail: sales@psfwales.co.uk • Website: www.psfwales.co.uk 


20 Nov 2011 279



Modular Security Enclosures 

Product 

Name 

Product 

Type 

Nominal 

Minimum 

External 

Height 

(m) 

Hercules 

SAF 3 

Hercules 

SAF 4 

Nominal 

Maximum 

External 

Height (m) 

Nominal 

Minimum 

External 

Width (m) 

Nominal 

Maximum 

External 

Width (m) 

Nominal 

Minimum 

External 

Depth (m) 

Nominal 

Maximum 

External 

Depth (m) 

Security 

Rating 

Modular 2.3 3.8 1.73 25 1.0 10 3 953b/01 

doorset 1 

enclosure 

with single 

leaf 

outward 

opening 

Modular 

enclosure 

with double 

leaf 

outward 

opening 

doorset 2 2.3 3.8 2.78 25 1.0 10 3 953b/02 

Modular 2.3 3.8 1.73 25 1.0 10 4 953b/03 

doorset 3 

enclosure 

with single 

leaf 

outward 

opening 

Modular 2.3 3.8 2.78 25 1.0 10 4 953b/04 

doorset 4 

enclosure 

with double 

leaf 

outward 

opening 

Cert. 

No. 

Approved Accessories 

Accessory 

Hercules SAF 3 and 4 Enclosure (LPCB Ref. No. 953b/..) 

01 02 03 04 

Shrouded vents (200 mm high by 350 mm w ide) 5 

Fixed roof 

Removable roof 

Notes: 

1. The approval covers the use of the Hercules SAF 3 single leaf doorsets (LPCB reference number 953a/01). 

2. The approval covers the use of the Hercules SAF 3 double leaf doorsets (LPCB reference number 953a/02). 

3. The approval covers the use of the Hercules SAF 4 single leaf doorsets (LPCB reference number 953a/03). 

4. The approval covers the use of the Hercules SAF 4 double leaf doorsets (LPCB reference number 953a/04). 

5. The vents shall not be located within 1.2 m of the locks on doorsets fitted to the enclosure. 

6. The approval covers the Hercules SAF 3 and 4 enclosures when installed in accordance with the ‘Installation instructions for Hercules 

SAF kiosk’ dated 2 February 2010. 



Product Product 

Name Type 

Hercules 

SAF 2 

Security 

enclosure 

with integral 

single or 

double leaf 1 

padlockable 

doorset 

Nominal 

Minimum 

External 

Height 

(m) 

Nominal 

Maximum 

External 

Height (m) 

Nominal 

Minimum 

External 

Width (m) 

Nominal 

Maximum 

External 

Width (m) 

Nominal 

Minimum 

External 

Depth (m) 

Nominal 

Maximum 

External 

Depth (m) 

Security 

Rating 

Cert. 

No. 

0.8 2.8 0.63 2.8 0.375 2.8 2 2 953c/01 


280 20 Nov 2011



Manufacturer Model Cylinder 

Abloy PL340/25 DP Abloy Disclock Pro 

Abloy PL340/25 PT Abloy Protec 

Abloy PL342 DP Abloy Disclock Pro 

Abloy PL342 PT Abloy Protec 

Accessories 

Type 

Shrouded vent w ith integrated 

vermin mesh. 

Description 

The shroud has external dimensions 300 mm (major height) by 200 mm (minor height) by 356 mm 

(w idth) by 100 mm (depth). It incorporates a 56 mm w ide by 312 mm long ventilation slot in the 

bottom fitted w ith a 100 mm by 100 mm vermin mesh. 

Notes: 

1. The scope of approval covers doorsets formed with leafs of widths between 0.35 m and 1.3 m and heights between 0.7 m and 2.8 m 

secured using the padlocks listed in the compatible padlock section. 

2. The security rating on the double doorset version of the security enclosure is achieved when both bolts on the passive leaf are 

engaged, the multi-point lock mechanism fitted to the primary leaf engaged and padlocked using one of the padlocks listed in the 

compatible padlock section. The double doorset version of the security enclosure achieved Security Rating 1 if only one of the tower 

bolts on the passive leaf was engaged. 

3. The approval does not cover the provision of any apertures within the enclosure fabric, other than the integral doorset or the 

shrouded vent described in the accessories section. 

4. The approval covers the Hercules SAF 2 pre-fabricated security enclosures when installed directly onto a concrete plinth in 

accordance with the instructions contained on PSF Wales Limited’s document SR2 K2 dated 29 March 2011. 

R & D Sheetmetal Limited 

Unit 1A, Victoria Court, Colliers Way, Clayton West, Huddersfield, West Yorkshire HD8 9TR, United Kingdom 

Tel: +44 (0)1484 864886 • Fax: +44 (0)1484 866505 

E-mail: sales@randdsheetmetal.co.uk • Website: www.randdsheetmetal.co.uk 


Modular Security Enclosure 

Product 

Name 

Product 

Type 

Minimum 

Height 

(m) 

Security 

Evo IV 

Security 

Evo V 

Security 

Evo VI 

Enclosure 

formed from 

four sides 

and a ceiling 

Enclosure 

formed from 

four sides 

and a ceiling 

Enclosure 

formed from 

four sides 

and a ceiling 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Depth (m) 

Maximum 

Depth (m) 

Security 

Rating 

Cert. No. 

1.9 2.7 1.1 2.4 0.8 Unlimited 4 1034a/01 

1.9 2.7 1.1 2.4 0.8 Unlimited 5 1034a/02 

1.9 2.7 1.1 2.4 0.8 Unlimited 6 1034a/03 


20 Nov 2011 281




Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Depth 

(m) 

Maximum 

Depth 

(m) 

Wall panel Wall panel 1.8 2.35 0.25 1.1 N/A N/A 

Roof panel 

Single roof panel 0.1 0.35 1.1 2.4 0.8 1.05 

End roof panel 0.1 0.35 1.1 2.4 0.25 1.05 

Mid roof panel 0.1 0.35 1.1 2.4 0.25 1.1 

Corner post Corner post 1.8 2.35 0.1 0.35 N/A N/A 

Doorsets 1 



Refer to Security Evo doorset range (LPCB Ref. No. 1034b) for scope of 

approval. 

Notes: 

1. Certification does not cover the use of locks other than those listed for use with the relevant R&D Sheetmetal Limited doorset. 

Utilisation of unlisted locks may affect the level of security offered by the doorset fitted to the enclosure. 

2. The enclosure’s resistance relies on the supporting substrate offering compatible resistance to manual attack. 

3. The Security Evo enclosure system is approved when installed in accordance with the instructions detailed on document EVO-INST- 

01 (Issue 3) and the general arrangement drawings supplied with the product. 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 



Security Cabinets 

Product Name 

Half Location Apparatus 

Case (LAC/H) 

Full Location Apparatus 

Case (LAC/F) 

Half Location Apparatus 

Case (LAC/H) 

Full Location Apparatus 

Case (LAC/F) 

Nominal Enclosure 

Height (mm) 


Width (mm) 


Depth (mm) 

Security 

Rating 

Cert. 

No. 

1850 575 535 3 450b/01 

1850 1010 535 3 450b/02 

1850 575 535 4 450b/03 

1850 1010 535 4 450b/04 


Padlock Designation Cylinder LPCB Ref. No 450b/… 

1 2 3 4 

Abloy PL240/25 Abloy High profile 

Abloy PL240/25EX Abloy Exec 

Abloy PL240/25DP Abloy Disklock Pro 

Abloy PL240/25PT Abloy Protec 

Abloy PL242 Abloy High Profile 

Abloy PL242EX Abloy Exec 

Abloy PL242DP Abloy Disklock Pro 

Abloy PL242PT Abloy Protec 

Abloy PL250/25 Abloy High Profile 







282 20 Nov 2011












Chubb 1K23c Chubb 6-pin 

Kaba KP15.0000C5-RB Kaba 20 (Armoured) 3 

Kaba K20SS65L Kaba 20 (Armoured) 3 

Kaba K20SS65CL Kaba 20 (Armoured) 3 

Rotalok 60/12/SE Kaba 20 (Armoured) 3 

Rotalok 60/12/SE Kaba 20 (Standard) 3 

Rotalok 60/12/ST Abloy Disklock Pro 

Rotalok 60/12/ST Abloy Exec 

Rotalok 60/12/ST Abloy Protec 

Rotalok 60/12/ST-T027 Assa Tw in-Combi 

Rotalok 60/12/ST Kaba 20 (Armoured) 3 

Rotalok 60/12/ST Kaba 20 (Standard) 3 

Notes: 

1. Certification does not cover the use of padlocks other than those listed above. Utilisation of unlisted padlocks may affect the level of 

security offered by the enclosure. 

2. The ‘user friendliness’ of employing the padlocks listed above has not been assessed as this is beyond the scope of LPS1175: Issue 

5. 

3. The torque resistant version of the Kaba 20 cylinder must be fitted to these padlocks in place of the standard Kaba 20 cylinders. 


Modular Security Cabinets and Building Systems 

Product 

Name 

Product Type Minimum 

Height 

(mm) 

Maximum 

Height 

(mm) 

Minimum 

Width 

(mm) 

WMC/DV4 Walk-In 

Modular 

Building 

System 

CB1/DV4 Small modular 

secure 

cabinet system 

with 

single leaf 

doorset 


secure 

cabinet system 

with 

double leaf 

doorset 

WMC/DV3 Walk-in 

modular 

building 

system 


secure cabinet 

system with 

single 

leaf doorset 


secure cabinet 

system with 

double 

leaf doorset 

Maximum 

Width 

(mm) 

Minimum 

Depth 

(mm) 

Maximum 

Depth 

(mm) 

Security 

Rating 

Cert. 

No. 

1500 3000 1000 5000 1000 10000 4 450c/01 

900 2000 650 5000 450 1500 4 450c/02 

900 2000 1350 5000 450 1500 4 450c/03 

1500 3000 1000 4000 1000 10000 3 450c/04 

900 2000 650 5000 450 1500 3 450c/05 

900 2000 1350 5000 450 1500 3 450c/06 


20 Nov 2011 283



Component 

Wall panels 

Roof panels 

Doorsets 1 

Type 

Minimum 

Height 

(mm) 

Maximum 

Height 

(mm) 

Minimum 

Width 

(mm) 

Maximum 

Width 

(mm) 

Minimum 

Depth 

(mm) 

Maximum 

Depth 

(mm) 

LPCB Ref No: 450c/… 

01 02 03 04 05 06 

Side panel 900 3000 450 1200 N/A N/A 

Side corner panel 900 3000 450 1200 N/A N/A 

Single piece side 900 2000 650 1800 450 1025 

panel 2 

Capping panel 3 150 2100 500 2600 N/A N/A 

"Security Rating 4" N/A N/A 450 1200 510 5060 

central roof panel 

 


central roof panel 

 


end roof panel 

 


end roof panel 

 

'One piece' roof N/A N/A 510 1200 710 5060 

panel 

 

Single leaf 


doorset 

Double leaf 


doorset 

Single leaf 


doorset 

Single leaf 


doorset 

Double leaf 


doorset 

For dimensions, please refer to UltraSecure DS1/DV4 doorset (LPCB Ref. 

No. 450a/03) 


No. 450a/08) 


No. 450d/01) 

For dimensions, please refer to UltraSecure DS1/LS3 doorset (LPCB Ref. 

No. 450d/02) 4 


No. 450d/03) 

 

 

 

 

 

 

 

 

 

 


Accessory 

LPCB Ref. No. 450c/… 

01 02 03 04 05 06 

Louvre vents 5 

Ultrasecure DV single, tw in or triple leaf access covers 6 

Notes: 

1 Certification does not cover the use of locks other than those listed for use with the relevant Technocover doorsets (LPCB Ref. No’s. 

450a/03 and 08, and 450d/01, 02 and 03). Utilisation of unlisted locks may affect the level of security offered by the doorset(s) fitted 

to the cabinet. 

2 Combined maximum size of panel is restricted by material availability. Refer to manufacturer before ordering. 

3 The following constraints apply to capping panel: 

a. If the panel height is less than 1200 mm, the maximum panel width is 2600 mm. 

b. If the panel height is greater than 1200 mm, the maximum panel width is 1200 mm. 

4 The following constraints apply when the UltraSecure DS1/LS3 door is fitted to CB1 cabinets or WMC modular buildings: 

a. Cabinet depth shall be at least 800 mm. 

b. Cabinet height shall be at least 1200 mm. 

c. Minimum distance on width side from leading edge of door leaf to side of cabinet is 625 mm. 

5 A maximum of six louvre vents may be fitted to each panel. 

6 The access covers fall within the scope of LPCB Ref. No’s. 450a/01, 02, 04, 05, 06 and 07. However, the maximum internal opening 

width is restricted to 1100 mm. 

Certificate No: 450i to LPS 1175: Issue 7 

284 20 Nov 2011

Modular Security Cage System 

Product 

Name 


Height 

(m) 

Ultrasecure 

security cage 

system 

Cage formed 

from one side 

and a ceiling 

supported by 

existing 

adjacent walls 

Cage formed 

from two sides 

supported by 

existing 


Cage formed 

from two sides 

and a ceiling 

supported by 

existing 


Cage formed 

from three 

sides 

supported by 

existing 


Cage formed 

from three 

sides and a 

ceiling 

supported by 

existing 


Cage formed 

from three 

sides 

supported by 

existing 


Cage formed 

from four sides 

and a ceiling 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Depth 

(m) 



Maximum 

Depth 

(m) 

Security 

Rating 

Cert. 

No. 

0.50 1 6 0.50 2 Unlimited 0.50 2 6 3 450i/01 

0.50 1 6 0.63 2 Unlimited 0.63 2 Unlimited 3 

0.50 1 6 0.63 2 Unlimited 0.63 2 6 3 


0.50 1 6 0.76 2 Unlimited 0.63 2 6 3 


0.50 1 6 0.76 2 Unlimited 0.76 2 6 3 



Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Mesh w all panel 0.50 6 0.25 1 N/A N/A 

Roof panel Mesh roof panel N/A N/A 0.25 1 0.50 6 

Corner post Corner post for cage 0.50 6 0.13 0.13 N/A N/A 

system 

Support post Support post for cage 0.46 5.91 0.165 0.165 N/A N/A 

system 

Doorsets Single leaf outw ard 




Refer to Ultrasecure SCD1 mesh security doorset (LPCB Ref. No. 450j/01) for 

scope of approval. 

Refer to Ultrasecure SCD2 mesh security doorset (LPCB Ref. No. 450j/02) for 

scope of approval. 

Notes: 

1. The minimum height of enclosures incorporating a doorset is 1.08 m. 

2. The minimum length of a side wall incorporating doorsets is 0.63 m. 

3. The cage’s resistance relies on the supporting substrate offering compatible resistance to manual attack. 

4. The Ultrasecure security cage system is approved when installed in accordance with the instructions detailed on document SCS-DV- 

3-FIT-01 (Ref.B). 

20 Nov 2011 285



Trimetals Limited 

Sunrise Business Park, Higher Shaftesbury Road, Blandford Forum, Dorset DT11 8ST, United Kingdom 

Tel: +44 (0)1258 459441 • Fax: +44 (0)1258 480408 

E-mail: sales@trimetals.co.uk • Website: www.trimetals.co.uk 


Bicycle and Motorcycle Store 

Product Name Type Model Nominal 

Internal 

Height 1 

Nominal 

Internal 

Width 

(m) 

Nominal 

Internal 

Depth 

(m) 

Security 

Rating 

Cert. No. 

(m) 

Protect a Cycle Bicycle store - 1.28 1.8 0.84 1 2 899a/01 

Protect a Bike Motorcycle store Standard pent roof model 2.0 1.4 2.7 2 3 899a/02 

Motorcycle store Wide pent roof model 2.0 1.6 2.7 2 3 

Motorcycle store Extra wide pent roof model 2.0 1.7 2.7 2 3 

Compatible Locking Devices 

Product Name Locking Device Manufacturer Model Description 

Protect a Cycle 

Protect a Bike 

Ground anchor 4 

Padlock 4 

Security cable 4 

Ground anchor 5 

Chain/padlock 5 

Oxford Products 

Limited 


Limited 

IR Safety and 

Security 


Limited 


Limited 

Oxford BruteForce 

(OF439) 

Oxford HD Mini (OF161) 

7 ft KryptoFlex Looped 

Cable (210610) 

Oxford RotaForce 

(OF438) 

Oxford Hardcore XL 

(OF118) 

Ground anchor 

Mini ‘U-lock’ padlock 

10 mm diameter by 2.2 m double 

looped security cable 

Ground anchor 

Security chain and padlock set 

Approved Installation Configurations 

Product Name 

Protect a Cycle 

Protect a Bike 

Configuration 

Mounted directly onto a flat level concrete surface at least 100 mm thick, in accordance 

w ith the ‘Protect a cycle assembly instructions’ (Issue 1 dated 6 October 2008) 

Mounted directly onto a flat level concrete surface at least 100 mm thick, in accordance 

w ith the ‘Pent roof shed assembly instructions’ 

Notes: 

1. This is the enclosure’s nominal internal height at the peaked section of the roof. 

2. The security rating relates to resistance to removal of complete bicycles, of designs incorporating enclosed frames (e.g. ‘diamond’, 

‘parallel top tube’, ‘single diagonal’, ‘mixte’ and ‘berceau’), that are secured within the ‘Protect a cycle’ bicycle store in accordance 

with the ‘Protect a cycle assembly instructions’ (Issue 1 dated 6 October 2008). 

3. The security rating relates to resistance to removal of complete motorcycles that are secured within the ‘Protect a bike’ motorcycle 

store in accordance with the ‘Trimetals Titan Range roof shed assembly instructions’. 

4. These locking devices must always be used to secure the bicycles within the security enclosure in order to achieve the security rating 

attributed to the ‘Protect a Cycle’ bicycle store. The cable should be passed through the centre of the bicycle frame and looped 

through the ground anchor and the two looped ends of the cable should both be secured using the padlock provided, as illustrated in 

‘step 15’ of the ‘Protect a cycle assembly instructions’ (Issue 1 dated 6 October 2008). 

5. These locking devices must always be used to secure the motorcycles within the security enclosure in order to achieve the security 

rating attributed to the ‘Protect a Bike’ motorcycle store. The chain should be passed through either the motorcycle frame or rear 

wheel and looped through the ground anchor and the two looped ends of the chain should both be secured using the padlock 

provided. 

286 20 Nov 2011


PHYSICAL SECURITY PROTECTION OF BUILDINGS 

Effective security relies on the appropriate combination of physical and electronic measures for the risks faced 

and the effective management of those facilities and maintenance of the security solutions and measures 

implemented. 

To prevent unauthorised entry into a building or area within a building, the components and materials used to 

construct that building/area must delay intruders sufficiently to allow an appropriate response. 

The effort an intruder needs to exert in order to gain entry is affected by a number of factors which, if 

countered by good physical security, will increase the likelihood of deterring potential intruders from even 

attempting entry. These factors include: 

Preparation and planning - The longer the criminal needs to take to survey a site and develop ways of 

overcoming the security measures without detection, the more likely they are to be deterred. 

Time spent attempting entry - The more the security delays the intruder when attempting entry, the greater 

the risk of them being caught and therefore the more likely they are to be deterred. 

Sourcing and transporting tools to overcome the physical security measures in place - The greater the 

number/weight of tools the intruder needs to use to overcome the security, and the more specialist the 

tools they need, the greater the risk of being caught and the more likely they are to be deterred. 

So how do specifiers determine whether physical security measures will be effective at deterring and delaying 

unauthorised entry? 

LPS 1175 Requirements and testing procedures for the LPCB approval and listing of intruder resistant 

building components, strongpoints, security enclosures and free-standing barriers classifies the resistance to 

forced entry provided by security products, systems and building materials. 

While previous versions of the standard specified six levels of resistance (security ratings), the latest versions 

(Issue 6 and 7) specify eight security ratings. The levels of risk on which the security ratings issued in issue 6 

and 7 are based are represented in the following chart. 

HIGH RISK 

LOW RISK 

LPS 1175 SR 8 

LPS 1175 SR 7 

LPS 1175 SR 6 

LPS 1175 SR 5 

LPS 1175 SR 4 

LPS 1175 SR 3 

LPS 1175 SR 2 

LPS 1175 SR 1 

Products certified to this standard provide 20 minutes of resistance 

to extreme means of attempting forced entry into higher value 

storage areas. 

Products certified to these standards provide 10 minutes of 

resistance to professional means of attempting forced entry into 

higher value storage areas using a wide range of tools including 

mains powered tools. 

Products certified to these standards resist experienced attempts at 

forced entry using a wide range of tools including battery powered 

tools lasting up to 10 minutes (SR 4 and 5) or 5 minutes (SR 3). 

Products certified to this standard provide 3 minutes of resistance to 

determined attack by an opportunist burglar using a range of 

techniques including those that involve creation of noise. 

Products certified to this standard provide 1 minute of resistance to 

opportunist attempts at entry using a range of techniques including 

those that create noise such as those involving breaking glass. 

20 Nov 2011 287



LPS 1175 supports the assessment, approval and specification of security doors, shutters and grilles together 

with many other products and systems designed to prevent unauthorised access by mechanical means. 

These include: 

Cladding Systems Garage Doors Sky Lights 

Fences and walls Roofing Systems Strongpoints and Enclosures 

Fixed Grilles Temporary Buildings Vehicles 

Folding Doorsets Sheds and Tool Stores Windows 

LPS 1175 is based on manual attack testing with the resistance provided by the products measured in terms 

of the attack tools and time available to the attacker. It enables specifiers to select products according to the 

risk. 

Further information on the security rating system and attack tools can be found in the standard itself, which 

can be downloaded from the Red Book web site www.RedBookLive.com. 

In addition to certifying windows, doors and shutters to LPS 1175, LPCB also offers approval of these 

products to the following standards: 

PAS 23-1 

PAS 24-1 

BS 7950 

General performance requirements for door assemblies - Part 1: Single leaf, external 

door assemblies to dwellings 

Enhanced security performance requirements for door assemblies - Part 1: Single and 

double leaf, hinged external door assemblies to dwellings 

Specification for enhanced security performance of windows for domestic applications 

EN 1627 Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - 

Requirements and classification 

PAS 23-1, PAS 24-1 and BS 7950 are aimed at domestic applications. Secured by Design report a significant 

reduction in domestic burglary where products approved to PAS 24-1 and BS 7950 have been used. 

The levels of resistance offered by products approved to PAS 24-1 and BS 7950 is generally lower than that 

provided by products approved to LPS 1175, especially if the products incorporate glass or in situations where 

the criminal can make sustained amounts of noise while attempting entry. 

EN 1627 is the European standard aimed at façade security products used in domestic and commercial 

situations. 

Specifiers should note that, although the working times specified for grades 2, 3 and 4 in EN 1627 match 

those defined for ratings 2, 3 and 4 in LPS 1175 (i.e. 3 minutes, 5 minutes and 10 minutes respectively), LPS 

1175 permits a far wider array of tools and attack techniques to be used. Specifiers should therefore not 

assume products meeting EN 1627 will offer the ‘same’ levels of resistance when tested to LPS 1175. 

In fact, a number of products rated to grade 4 in ENV 1627 tested by BRE to LPS 1175 have failed to achieve 

above a Security Rating 2 classification. 

Furthermore, because anyone can test products to EN 1627 and the quality of testing can greatly impact on 

the ratings attributed to a product, this can affect the resistance to attack actually delivered by products rated 

to the standard. LPCB therefore only recognises those tests conducted to this standard by its own 

experienced test engineers or by other laboratories that have demonstrated they conduct the tests to suitably 

high standards. 

Hotel Doorsets 

In addition to these standards, LPCB has developed a standard for Hotel Doorsets. LPS 1268 Specification 

for the testing and classification of hotel bedroom doorsets covers many aspects of the doorset’s 

288 20 Nov 2011



performance, from security performance through to fire resistance, acoustic and general durability. Copies of 

the standard are available free of charge and can be obtained by emailing enquiries@breglobal.com 

Product Selection 

When selecting a security door, shutter, grille or other façade element, it is important to note aspects such as 

the size, locking systems, modes and directions of opening, and the type, size and location of any glazing 

incorporated within the product or system. All can affect the level of security provided by the product. These 

aspects of each certified product have therefore been described to enable selection of the most appropriate 

product for the desired application. Where options, such as glazed in-fills within door leaves, are not covered 

in the listing, those options fall outside the scope of that product’s approval. 

Unless otherwise stated, the security ratings attributed to the products listed require all lock bolts to be fully 

engaged and any deadlocking mechanism provided must be engaged. If a product is shown to achieve more 

than one security rating: 

The lower rating indicates the security rating achieved by the product when in the “minimum locked 

condition”, that is, when the opening element (e.g. door leaf) is closed and only automatic latching 

mechanisms are engaged. 

The higher rating indicates the security rating achieved by the product when any additional manually 

operated deadlocks fitted to the opening element are engaged. 

It is important to ensure that the products are installed in accordance with the manufacturer’s instructions and 

that all exposed fixings, the substrate into which the device is fitted and the locking mechanisms are regularly 

checked to ensure that they are in good condition and that they have not been tampered with. For added 

peace of mind, we recommend products are installed by companies certified to LPS 1271 Requirements for 

the LPCB Approval and Listing of companies installing fire and security doorsets and shutters, and smoke 

barriers for a scope covering the product being specified. A list of currently approved installers is provided in 

Volume 2. 

20 Nov 2011 289


HIGH SECURITY DOORSETS 

Doorsets listed in this section are approved to LPS 1175 Requirements and testing procedures for the LPCB 

approval and listing of intruder resistant building components, strongpoints, security enclosures and freestanding 

barriers. 

Section 5.1.1 lists high security plain leaf hinged doorsets 

Section 5.1.2 lists high security glazed hinged doorsets 

Section 5.1.3 lists high security hinged doorsets with other leaf designs, such as those incorporating mesh or 

fixed bars. 

Section 5.1.4 lists high security folding doorsets 

For details of hinged doorsets approved to PAS 23-1 and PAS 24-1 please refer to sections 5.2.1 and 5.2.2 

respectively. 

290 20 Nov 2011


HIGH SECURITY HINGED DOORSETS WITH PLAIN LEAVES 

AccentHansen 

Greengate Industrial Park, Greengate, Middleton, Manchester M24 1SW, United Kingdom 

Tel: +44 (0)161 284 4100 • Fax: +44 (0)161 655 3119 

E-mail: info@accenthansen.co.uk • Website: www.servicehansen.com 


Hinged Security Doorsets 

Product 

Name 

Type 

Frame 

Dimensions 

Height 

(m) 

Secureshield 

4 

Single leaf, 

outward 

opening hinged 

security doorset 

Double leaf, 

outward 



Double leaf, 

outward 


security 

Single leaf, 

outward 



Frame 

Dimensions 

Width 

(m) 

Compatible 

Locking 

Systems 

on Active 

Leaf 

Compatible 

Locking 

Systems 

on Passive 

Leaf 

Locked 

Condition 

Security 

Rating 

Cert. 

No. 

2.090 1.275 3 N/A Minimum 3 021c/01 

2.090 1.775 3 4, 5 or 6 Minimum 3 

2.090 1.775 1, 2 or 3 4, 5 or 6 Optimum 4 

2.090 1.275 1, 2 or 3 N/A Optimum 4 

Compatible Locking Systems 

20 Nov 2011 291



Compatible 

Locking 

System 

Locking System Type Locked Compatible operating devices 

Condition External Face Internal Face 

1 Assa Mico 942-3 MSD 1 Three point panic 

exit device fitted 

w ith MSD 

deadlocking device 

2 Assa Mico 942-3P MSD 1 Three point 

emergency exit 

device operated by 

a push pad and 

fitted w ith the MSD 


3 Assa Mico 942-3L MSD 1 Three point 



a lever handle and 

fitted w ith the MSD 


4 Assa Mico 942 Tw o point panic exit 

device 

5 Assa Mico 942P Tw o point 



a push pad 

6 Assa Mico 942L Tw o point 



a lever handle 

Optimum 2 None Key and panic 

bar 

Optimum 2 None Key and push 

pad 

Optimum 2 

Minimum 

None 

None 

None 

None 

Key and lever 

handle 

Lever handle 

Panic bar 

Push pad 

Lever handle 

Notes: 

1. The MSD (Micro Switched Deadlock) system is operated by key from inside. This must be deadlocked in order to achieve the level of 

security relating to the optimum locked condition. 

2. Although outside the scope of LPS1175: Issue 5, special consideration should be paid to the deadlocking of the Assa Mico panic and 

emergency three point locking system. This is because it is generally not acceptable to separately deadlock a doorset that is fitted 

with a panic or emergency exit device unless the deadlock is automatically operated by the action of the panic or emergency device, 

since doing so can inhibit means of escape. For further information, reference should be made to the appropriate standards for 

emergency exit and panic exit devices, i.e. BS EN 179 and BS EN 1125 respectively. 



Product 

Name 

Doorset 

Configuration 

Minimum 

Structural 

Opening 

Height 

(m) 

SecureShield 

2 

Single leaf 

outward 

opening 

hinged security 

doorset 

Single leaf 

outward 

opening 


doorset 

Single leaf 

outward 

opening 


doorset 

Maximum 

Structural 

Opening 

Height 

(m) 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

Minimum 

Structural 

Opening 

Width 

(m) 

Maximum 

Structural 

Opening 

Width 

(m) 

Locking 

System 

Active 

Leaf 

Locking 

Sysetm 

Passive 

Leaf 

Security 

Rating 

Cert. 

No. 

0.5 1.25 1 - 2 021d/01 

0.5 1.25 2 - 2 

0.5 1.25 3 - 2 

292 20 Nov 2011



Product 

Name 

Doorset 

Configuration 

Single leaf 

outward 

opening 


doorset 

Double leaf 

outward 

opening 


doorset 

Double leaf 

outward 

opening 


doorset 

Double leaf 

outward 

opening 


doorset 

Double leaf 

outward 

opening 


doorset 

Minimum 

Structural 

Opening 

Height 

(m) 

Maximum 

Structural 

Opening 

Height 

(m) 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

1.5 Refer to 

compatible 

locking 

systems 

Minimum 

Structural 

Opening 

Width 

(m) 

Maximum 

Structural 

Opening 

Width 

(m) 

Locking 

System 

Active 

Leaf 

Locking 

Sysetm 

Passive 

Leaf 

Security 

Rating 

0.5 1.25 6 - 2 

Cert. 

No. 

1.3 2.5 1 4 2 021d/02 

1.3 2.5 2 4 2 

1.3 2.5 5 5 2 

1.3 2.5 7 7 2 


Compatible 

Locking 

System 

Manufacturer Model Description Maximum 

Structural 

Opening 

Height (m) 

1 Associated 

Finishers Limited 

2 Associated 

Finishers Limited 

3 Fred Duncombe 

Limited 

Compatible 

Cylinders 

QFSL Sashlock 2.4 A 

QFDL Deadlock 2.4 A 

Exidor 

702B/30S w ith 

710EC 

Tw o point panic bar locking 

system w ith external access 

device 

2.45 B 


Limited 

Exidor HS923 Tow er bolts 2.4 - 


Limited 

Exidor 

701BD/30S 

w ith 710EC 

Double door panic bar locking 

system (single point anti-thrust 

panic exit locking system w ith 

external access device on active 

leaf and a tw o point panic exit 

locking system on passive leaf) 

2.4 B 


Limited 


Limited 

Exidor 

702B/30S 

Exidor 

701BD/30S 

Tw o point panic bar locking 

system w ith no external entry 

Double door panic bar locking 

system w ith no external entry 

(single point anti-thrust panic exit 

locking system and a tw o point 

panic exit locking system on 

passive leaf) 

2.45 - 

2.4 - 


20 Nov 2011 293




Reference 

A Assa R527 Double europrofile cylinder (key:thumbturn) 

B Zone 1500 Single europrofile cylinder 



Tel: +44 (0)1204 545801 • Fax: +44 (0)1204 545800 




Product Name Doorset 

Configuration 

Centurion A355 

Centurion A364S 

Centurion A364D 



Single leaf, 

outward 


doorset 

Single leaf, 

outward 


doorset 

Double leaf, 

outward 


doorset 

Single leaf, 

outward 


doorset 

Double leaf, 

outward 


doorset 

Minimum 

Clear 

Opening 

Height (m) 

Minimum 

Clear 

Opening 

Width (m) 

Maximum 

Clear 

Opening 

Height (m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 1 

Cert. No. 

1.8 0.7 2.5 1.35 4 131d/01 

1.8 0.7 2.9 1.35 4 131d/02 

1.8 1.4 2.9 2.61 4 131d/03 

1.8 0.7 2.9 1.35 3 131d/04 

1.8 1.4 2.9 2.61 3 131d/05 

Compatible Locking Configurations 

294 20 Nov 2011



Product Name 


Doorset 

Configuration 


Active Leaf 

Passive Leaf 

Single leaf, outw ard 

19 N/A 

security doorset 2 






Single leaf, outw ard 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 

opening hinged 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 

security doorset 2 26, 27, 28, 29, 30, 31, 32, 33, 34 and 

35 

Double leaf, outw ard 4, 5, 6, 7, 8, 9, 10 ,11, 12, 13, 14, 15, 


security doorset 2,3 26, 27, 28, 29, 30, 31, 32, 33, 34 and 

35 

Single leaf, outw ard 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 


security doorset 2 44, 45, 46, 47, 48, 49, 50, 51, 52, 53 

and 54 

Double leaf, outw ard 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 


security doorset 2,3 44, 45, 46, 47, 48, 49, 50, 51, 52, 53 

and 54 

N/A 

1, 2, 3 

N/A 

1, 2, 3 


Compatible 

Locking 

Systems 

Manufacturer Model Type Compatible Operating Devices 

1 Tindall 

Engineering Ltd 

Mico 942 

2-w ay panic exit 

device 

External Face 

Internal Face 

Compatible 

Cylinders 4 

None Panic bar - 

2 Tindall 


Mico 942P 

2-w ay emergency 

exit device 

None Push pad - 

3 Tindall 


Mico 942L 


exit device 

None Lever handle - 

4 Tindall 


Mico 942-3 / ELK 

3 


device 

Key (via ELK3) Panic bar A 

5 Tindall 


Mico 942-3 


device 


20 Nov 2011 295



6 Tindall 


Mico 942-3P / 

ELK 3 


exit device 

Key (via ELK3) Push pad A 

7 Tindall 


Mico 942-3P 


exit device 


8 Tindall 


Mico 942-3L / 

ELK 3 


exit device 

Key (via ELK3) Lever handle A 

9 Tindall 


Mico 942-3L 


exit device 


10 Tindall 


Mico 942-3 EM 

SEC / HSCH 3 

3-w ay locking External access 

system w ith solenoid control device 6 or 

deadlock and electromechanical 

access HSCH3 cylinder 

key override w ith 

control pow ered by guard and lever 

12 V 5 handle 

Internal access 

control device or 

thumbturn 

override and ‘full 

w idth’ push plate 

B 

11 Tindall 


Mico 942-3 EM 

SEC 


system w ith solenoid control device 6 


access 


control pow ered by 

12 V 5 



thumbturn 



- 

12 Tindall 


Mico 942-3P EM 

SEC / HSCH 3 







12 V 5 handle 



thumbturn 

override and push 

pad 

B 

13 Tindall 



SEC 




access 



12 V 5 



thumbturn 


pad 

- 

14 Tindall 


Mico 942-3L EM 

SEC / HSCH 3 







12 V 5 handle 



thumbturn 

override and lever 

handle 

B 

15 Tindall 



SEC 




access 



12 V 5 



thumbturn 


handle 

- 

296 20 Nov 2011



16 Tindall 


Mico 942-3L INT 

AD / HSCH 3 

3-w ay locking 

system w ith 

automatic deadlock 

HSCH3 cylinder 

guard and lever 

handle 

Thumbturn and 

lever handle 

B 

17 Tindall 



AD 


system w ith 


None 

Thumb turn and 

lever handle 

- 

18 Tindall 


Mico 942-3 INT 

MD / HSCH 3 


system w ith manual 

deadlock 



handle 

Key or thumbturn 

and full w idth 

push plate 

B 

19 Tindall 



MD 



deadlock 

None 



push plate 

- 

20 Tindall 


Mico 942-3P INT 

MD / HSCH 3 



deadlock 



handle 


and push pad 

B 

21 Tindall 



MD 



deadlock 

None 


and push pad 

- 

22 Tindall 



MD / HSCH 3 



deadlock 



handle 



B 

23 Tindall 



MD 



deadlock 

None 



- 

24 Tindall 


Mico 942-3 

SATE EM SEC / 

HSCH 3 

3-w ay panic exit External access 

device w ith solenoid control device 6 or 

deadlock and electro key override w ith 

mechanical access HSCH3 cylinder 


12 V 5 handle 

Panic bar 

B 

25 Tindall 


Mico 942-3 SATE 

EM SEC 


device w ith solenoid control device 6 

deadlock and electro and lever handle 

mechanical access 


12 V 5 

Panic bar - 

20 Nov 2011 297



26 Tindall 


Mico 942-3P 

SATE EM SEC / 

HSCH 3 

3-w ay emergency External access 

exit device w ith control device 6 or 

solenoid deadlock key override w ith 

and electro HSCH3 cylinder 

mechanical access guard and lever 

control pow ered by handle 

12 V 5 

Push pad 

B 

27 Tindall 


Mico 942-3P 

SATE EM SEC 


exit device w ith control device 6 

solenoid deadlock and lever handle 

and electro 



12 V 5 

Push pad - 

28 Tindall 


Mico 942-3L 

SATE EM SEC / 

HSCH 3 







12 V 5 

Lever handle 

B 

29 Tindall 


Mico 942-3L 

SATE EM SEC 


exit device w ith control device 6 

solenoid deadlock and lever handle 

and electro 



12 V 5 

Lever handle - 

30 Tindall 



AD / HSCH 3 


device w ith 


Key via HSCH3 



Panic bar 

B 

31 Tindall 


Mico 942-3P 3-w ay emergency 

SATE AD / HSCH exit device w ith 

3 


Key via HSCH3 



Push pad 

B 

32 Tindall 


Mico 942-3L 3-w ay emergency 


3 


Key via HSCH3 



Lever handle 

B 

33 Tindall 



MD / HSCH 3 


device w ith manual 

deadlock 

Key via HSCH3 



Panic bar 

B 

34 Tindall 



SATE MD / HSCH exit device w ith 

3 

manual deadlock 

Key via HSCH3 



Push pad 

B 

35 Tindall 




3 


Key via HSCH3 



Lever handle 

B 

298 20 Nov 2011



36 Tindall 


Mico 942-3 / ELK 

4 


device 

Key (via ELK4) Panic bar A 

37 Tindall 


Mico 942-3P / 

ELK 4 


exit device 

Key (via ELK4) Push pad A 

38 Tindall 


Mico 942-3L / 

ELK 4 


exit device 

Key (via ELK4) Lever handle A 

39 Tindall 


Mico 942-3 EM 

SEC / HSCH 4 







12 V 5 handle 



thumbturn 



B 

40 Tindall 



SEC / HSCH 4 







12 V 5 handle 



thumbturn 


pad 

B 

41 Tindall 



SEC / HSCH 4 







12 V 5 handle 



thumbturn 


handle 

B 

42 Tindall 



AD / HSCH 4 


system w ith 




handle 

Thumbturn and 

lever handle 

B 

43 Tindall 



MD / HSCH 4 



deadlock 



handle 



push plate 

B 

44 Tindall 



MD / HSCH 4 



deadlock 



handle 


and push pad 

B 

45 Tindall 



MD / HSCH 4 



deadlock 



handle 



B 

20 Nov 2011 299



46 Tindall 


Mico 942-3 

SATE EM SEC / 

HSCH 4 


device w ith solenoid control device 6 or 

deadlock and electro key override w ith 

mechanical access HSCH4 cylinder 


12 V 5 handle 

Panic bar 

B 

47 Tindall 


Mico 942-3P 

SATE EM SEC / 

HSCH 4 







12 V 5 

Push pad 

B 

48 Tindall 


Mico 942-3L 

SATE EM SEC / 

HSCH 4 







12 V 5 

Lever handle 

B 

49 Tindall 



AD / HSCH 4 


device w ith 


Key via HSCH4 



Panic bar 

B 

50 Tindall 




4 


Key via HSCH4 



Push pad 

B 

51 Tindall 




4 


Key via HSCH4 



Lever handle 

B 

52 Tindall 



MD / HSCH 4 



deadlock 

Key via HSCH4 



Panic bar 

B 

53 Tindall 




4 


Key via HSCH4 



Push pad 

B 

54 Tindall 




4 


Key via HSCH4 



Lever handle 

B 



Reference 

A Assa 4801 Half oval mechanical cylinder 

B Assa 4807 Half oval mechanical cylinder 

Notes: 

1. These ratings apply to doorsets with locking fully engaged, i.e. in optimum locked condition. The doorsets achieve Security Rating 2 

when the following locking systems are fitted and left in the minimum locked condition, e.g. internal manual deadlock not engaged: 

18, 19, 20, 21, 22, 23, 43, 44 and 45. 

2. Although outside the scope of LPS 1175: Issue 6, special consideration should be paid to the use of locking systems with separate 

deadlocks, e.g. Mico 942-3 INT MD. This is because it is generally not acceptable to separately deadlock a doorset that is fitted with a 

300 20 Nov 2011



panic or emergency exit device unless the deadlock is automatically operated by the action of the panic or emergency device. For 

further information, please refer to the appropriate standards for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 

respectively. 

3. Although outside the scope of LPS 1175: Issue 6, special consideration should be paid to the use of single operating panic or 

emergency exit devices. This is because it is generally accepted that when two panic or emergency exit devices are fitted to double 

doorsets the operation of either device should disengage simultaneously such that both leafs can open. For further information, 

please refer to the appropriate standard for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 respectively. 

4. This is applicable to the external cylinders only. Due to the resistance afforded by the doorset there is no restrictions on the type of 

internal cylinder used. 

5. Fail secure version only. 

6. The resistance of the access control locks to “non-mechanical” attack has not been assessed as it is outside the scope of LPS 1175. 

Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and performance of any 

access control equipment that may be used to operate these locking systems. This is because the scope of access control devices 

and system configurations that may be used with these locking systems is “infinite”. It is therefore recommended that Ascot Doors 

Limited satisfy themselves that the components are either resistant to mechanical and other forms of tampering/abuse, or that they 

are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may cause the 

locking system to disengage. 

Bradbury Security 

Dunlop Way, Queensway Industrial Estate, Scunthorpe DN16 3RN, United Kingdom 

Tel: +44 (0)1724 271999 • Fax: +44 (0)1724 271888 

E-mail: sales@bradburyuk.com • Website: www.bradburyuk.com 



Product 

Type 

Name 

Fortress 2 

Single leaf outward opening security 

louvered door 

Minimum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.5 0.5 2.3 1.0 2 312c/01 


Lock Type Approved product (LPCB Ref. No. 312c/01) 

Siver 921 Three-point locking system 


Hinged Doorsets 

Product 

Name 

M2M 1 

Type 

Single leaf outward 

opening hinged security 

doorset 

Minimum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Compataible 

Locking 

Systems 

Security 

Rating 

Cert. 

No. 

1745 2475 740 1210 1, 2, 4 and 5 1 312d/01 

1745 2410 740 990 3 1 

Compataible Locking Systems 

20 Nov 2011 301



Option Manufacturer Type Operating Devices 

1 Union JL2C21R sash 

lock 

External Face 

Key and lever 

handle 

Internal face 

Key and lever 

handle 

Compatible 

Cylinders 

Baton double 

europrofile 

cylinder (key:key) 

2 Union JL2C22R dead 

lock 

Key and fixed 

pull handle 

Key and fixed pull 

handle 

Baton double 

europrofile 


3 Yale Yale 82 

deadbolt 

4 IDC IDC 736 2 point 

panic exit 

system 

Key and fixed 

pull handle 

5 Hooply Combat Key and lever 

multipoint handle 

locking system 

Turn handle 

None Panic bar None 

Thumbturn and 

lever handle 

Yale 82 rim 

cylinder 

Combat 65 mm 

europrofile double 

cylinder 

(key:thumbturn) 



Product 

Name 


Structural 

Opening Height 

(m) 

M2M3 Single leaf 

outward 

opening 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.745 2.43 0.74 1.18 3 1, 2, 3 312e/01 

doorset 

Double leaf 1.745 2.43 1.15 2.20 3 

doorset 4 

outward 

opening 

1, 2, 3 

Approved Locking Configurations 

LPCB 

Ref. No. 

Product 

Name 

312e/01 M2M3 

Type 


Active Leaf 

Passive Leaf 

Single leaf outw ard opening plain leafed doorset 5 1, 3 to 182 N/A 

Single leaf outw ard opening louvred doorset 2 N/A 

Double leaf outw ard opening plain leafed doorset 5, 6, 7 1, 3 to 182 62, 64, 66, 76, 78, 103, 

105, 107, 109, 183 or 184 

Double leaf outw ard opening louvred doorset 2 183 or 184 

Compatible Locking Devices 8 

302 20 Nov 2011



Compatible Manufacturer Model Type Com patible Operating Device Compatible 

Locking 

Cylinders 

System 

External Face Internal Face 

1 Hooply Combat Multi-point locking Key and lever handle Key and lever handle AB 

system 

2 Bradbury 

Security 

- 4-w ay locking 

mechanism 

Key and lever handle Latch mechanism 


AW, AX, AY and 

AZ 

3 Tindall 

Engineering 

Limited 

Abryll PE2 

/ELK3 

Single point panic 

exit device 

Key and lever handle Panic bar A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q and R 

4 Tindall 

Engineering 

Limited 

5 Tindall 

Engineering 

Limited 

6 Tindall 

Engineering 

Limited 

7 Tindall 

Engineering 

Limited 

8 Tindall 

Engineering 

Limited 

9 Tindall 

Engineering 

Limited 

Abryll PE2 

Abryll PE1 

/ELK3 

Abryll PE1 

Abryll PE3 

/ELK3 

Abryll PE3 

Abryll EM2 

/USCH3 


exit device 

Single point 


device 

Single point 


device 

Single point 


device 

Single point 


device 

Single point locking 

system w ith solenoid 

deadlocking and 12v 

electro-mechanical 

access control 9 


Key and lever handle Push pad A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q and R 


Key and lever handle Lever handle A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q and R 


Electro-mechanical 

access control 

device 10 w ith key 


handle 



device w ith thumb 

turn override and 

push plate 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 

AX, AY, AZ, BA, 

BB and BC 

10 Tindall 

Engineering 

Limited 

Abryll EM2 








device 10 and lever 

handle 





push plate 

- 

11 Tindall 

Engineering 

Limited 

Abryll EM1 

/USCH3 










handle 





push pad 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

12 Tindall 

Engineering 

Limited 

Abryll EM1 









handle 





push pad 

- 

20 Nov 2011 303



13 Tindall 

Engineering 

Limited 

Abryll EM3 

/USCH3 










handle 





lever handle 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

14 Tindall 

Engineering 

Limited 

Abryll EM3 









handle 





lever handle 

- 

15 Tindall 

Engineering 

Limited 

16 Tindall 

Engineering 

Limited 

17 Tindall 

Engineering 

Limited 

18 Tindall 

Engineering 

Limited 

19 Tindall 

Engineering 

Limited 

20 Tindall 

Engineering 

Limited 

21 Tindall 

Engineering 

Limited 

22 Tindall 

Engineering 

Limited 

23 Tindall 

Engineering 

Limited 

24 Tindall 

Engineering 

Limited 

Abryll AD3 

/USCH3 

Abryll AD3 

Abryll MD2 

/USCH3 

Abryll MD2 

Abryll MD1 

/USCH3 

Abryll MD1 

Abryll MD3 

/USCH3 

Abryll MD3 

Abryll SATE 

EM2 /USCH3 

Abryll SATE 

EM2 


system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 


exit device w ith 

solenoid deadlocking 

and 12v electromechanical 

access 

control 9 





access 

control 9 

Key and lever handle 

None 


None 


None 


None 





handle 




handle 





Key or thumb turn 

and push plate 




and push pad 


and push pad 





A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

Panic bar A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Panic bar - 

304 20 Nov 2011

25 Tindall 

Engineering 

Limited 

26 Tindall 

Engineering 

Limited 

27 Tindall 

Engineering 

Limited 

28 Tindall 

Engineering 

Limited 

29 Tindall 

Engineering 

Limited 

30 Tindall 

Engineering 

Limited 

31 Tindall 

Engineering 

Limited 

32 Tindall 

Engineering 

Limited 

33 Tindall 

Engineering 

Limited 

34 Tindall 

Engineering 

Limited 

Abryll SATE 

EM1 /USCH3 

Abryll SATE 

EM1 

Abryll SATE 

EM3 /USCH3 

Abryll SATE 

EM3 

Abryll SATE 

AD2/USCH3 

Abryll SATE 

AD1/USCH3 

Abryll SATE 

AD3/USCH3 

Abryll SATE 

MD2/USCH3 

Abryll SATE 

MD1/USCH3 

Abryll SATE 

MD3/USCH3 



Single point 


device w ith solenoid 




Single point 






Single point 






Single point 








automatic 

deadlocking 

Single point 


device w ith 

automatic 

deadlocking 

Single point 


device w ith 

automatic 

deadlocking 



manual deadlocking 

Single point 



deadlocking 

Single point 



deadlocking 





handle 




handle 





handle 




handle 

Push pad A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Push pad - 

Lever handle A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


Key and lever handle Panic bar A, B, C, D, E, F, 

G, H, I, J, K, L, M, 

N, O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Key and lever handle Lever handle A, B, C, D, E, F, 

G, H, I, J, K, L, M, 

N, O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

20 Nov 2011 305



35 Tindall 

Engineering 

Limited 

36 Tindall 

Engineering 

Limited 

37 Tindall 

Engineering 

Limited 

38 Tindall 

Engineering 

Limited 

39 Tindall 

Engineering 

Limited 

40 Tindall 

Engineering 

Limited 

41 Tindall 

Engineering 

Limited 

42 Tindall 

Engineering 

Limited 

43 Tindall 

Engineering 

Limited 

44 Tindall 

Engineering 

Limited 

45 Tindall 

Engineering 

Limited 

Abryll PE2 / 

EURO 

ELK 3 

Abryll 

PE1/EURO 

ELK3 

Abryll 

PE3/EURO 

ELK3 

Abryll EPC 

EM2/USCH3 

Abryll EPC 

EM2 

Abryll EPC 

EM1/USCH3 

Abryll EPC 

EM1 

Abryll EPC 

EM3/USCH3 

Abryll EPC 

EM3 

Abryll EPC 

AD3 /USCH 3 

Abryll EPC 

AD3 


exit device 

Single point 


device 

Single point 


device 
































system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 

Key and lever handle Panic bar S, T, U, V, W, X 

Y, Z and AA 

Key and lever handle Push pad S, T, U, V, W, X 

Y, Z and AA 

Key and lever handle Lever handle S, T, U, V, W, X 

Y, Z and AA 





handle 




handle 





handle 




handle 





handle 




handle 


None 





push plate 





push plate 





push pad 





push pad 





lever handle 





lever handle 





AE, AF, AG, AH, 

AJ, AL, AN, AP, 

AR, AT and AV 

- 



AR, AT and AV 

- 



AR, AT and AV 

- 

AC, AD, AE, AF, 

AG, AH, AI, AJ, 

AK, AL, AM, AN, 

AO, AP, AQ, AR, 

AS, AT, AU and 

AV 

- 

306 20 Nov 2011

46 Tindall 

Engineering 

Limited 

47 Tindall 

Engineering 

Limited 

48 Tindall 

Engineering 

Limited 

49 Tindall 

Engineering 

Limited 

50 Tindall 

Engineering 

Limited 

51 Tindall 

Engineering 

Limited 

52 Tindall 

Engineering 

Limited 

53 Tindall 

Engineering 

Limited 

54 Tindall 

Engineering 

Limited 

55 Tindall 

Engineering 

Limited 

56 Tindall 

Engineering 

Limited 

57 Tindall 

Engineering 

Limited 

Abryll EPC 

MD2/USCH3 

Abryll EPC 

MD2 

Abryll EPC 

MD1/USCH3 

Abryll EPC 

MD1 

Abryll EPC 

MD3/USCH3 

Abryll EPC 

MD3 

Abryll EPC 

SATE 

EM2/USCH3 

Abryll EPC 

SATE 

EM1/USCH3 

Abryll EPC 

SATE 

EM3/USCH3 

Abryll EPC 

SATE 

AD2/USCH3 

Abryll EPC 

SATE 

AD1/USCH3 

Abryll EPC 

SATE 

AD3/USCH3 





deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 





access 

control 9 

Single point 






Single point 








automatic 

deadlocking 

Single point 


device w ith 

automatic 

deadlocking 

Single point 


device w ith 

automatic 

deadlocking 


None 


None 


None 





handle 





handle 





handle 






and push pad 


and push pad 










AV 

- 






AV 

- 






AV 

- 

Panic bar S, T, U, V, W, X, 

Y, Z and AA 

Push pad S, T, U, V, W, X, 

Y, Z and AA 

Lever handle S, T, U, V, W, X, 

Y, Z and AA 

Key and lever handle Panic bar S, T, U, V, W, X, 

Y, Z and AA 

Key and lever handle Push pad S, T, U, V, W, X, 

Y, Z and AA 

Key and lever handle Lever handle S, T, U, V, W, X, 

Y, Z and AA 

20 Nov 2011 307



58 Tindall 

Engineering 

Limited 

59 Tindall 

Engineering 

Limited 

60 Tindall 

Engineering 

Limited 

61 Tindall 

Engineering 

Limited 

62 Tindall 

Engineering 

Limited 

63 Tindall 

Engineering 

Limited 

64 Tindall 

Engineering 

Limited 

65 Tindall 

Engineering 

Limited 

66 Tindall 

Engineering 

Limited 

67 Tindall 

Engineering 

Limited 

68 Tindall 

Engineering 

Limited 

69 Tindall 

Engineering 

Limited 

Abryll EPC 

SATE 

MD2/USCH3 

Abryll EPC 

SATE 

MD1/USCH3 

Abryll EPC 

SATE 

MD3/USCH3 

Mico 942 /ELK 

3 

Mico 942 

Mico 942P 

/ELK 3 

Mico 942P 

Mico 942L 

/ELK 3 

Mico 942L 

Mico 942 EM 

SEC 

/USCH 3 

Mico 942 EM 

SEC 

Mico 942P EM 

SEC /USCH 3 




Single point 



deadlocking 

Single point 



deadlocking 


device 


device 


exit device 


exit device 


exit device 


exit device 

2- w ay locking 
















Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


H, I, J, K, L, M, N, 

O, P, Q and R 


Key (via ELK 3) and 

lever handle 


H, I, J, K, L, M, N, 

O, P, Q and R 



lever handle 


H, I, J, K, L, M, N, 

O, P, Q and R 






handle 




handle 





handle 





push plate 





push plate 





push pad 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, 

G, H, I, J, K, L, M, 

N, O, P, Q, R, AW, 


BB and BC 

308 20 Nov 2011



70 Tindall 

Engineering 

Limited 

Mico 942P EM 

SEC 









handle 





push pad 

- 

71 Tindall 

Engineering 

Limited 

Mico 942L EM 

SEC /USCH 3 










handle 





lever handle 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

72 Tindall 

Engineering 

Limited 

Mico 942L EM 

SEC 









handle 





lever handle 

- 

73 Tindall 

Engineering 

Limited 

74 Tindall 

Engineering 

Limited 

75 Tindall 

Engineering 

Limited 

76 Tindall 

Engineering 

Limited 

77 Tindall 

Engineering 

Limited 

78 Tindall 

Engineering 

Limited 

79 Tindall 

Engineering 

Limited 

80 Tindall 

Engineering 

Limited 

81 Tindall 

Engineering 

Limited 

Mico 942L INT 

AD /USCH 3 

Mico 942L INT 

AD 

Mico 942 INT 

MD /USCH 3 

Mico 942 INT 

MD 

Mico 942P INT 

MD /USCH 3 

Mico 942P INT 

MD 

Mico 942L INT 

MD /USCH 3 

Mico 942L INT 

MD 

Mico 942 

SATE EM SEC 

/USCH 3 


system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 

2- w ay panic exit 





Key and lever handle Thumb turn and lever 

handle 

None 


None 


None 

Key (via USCH 3) 


None 





handle 

Thumb turn and lever 

handle 






and push pad 


and push pad 





A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Push plate A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

20 Nov 2011 309



82 Tindall 

Engineering 

Limited 

83 Tindall 

Engineering 

Limited 

84 Tindall 

Engineering 

Limited 

85 Tindall 

Engineering 

Limited 

86 Tindall 

Engineering 

Limited 

87 Tindall 

Engineering 

Limited 

88 Tindall 

Engineering 

Limited 

89 Tindall 

Engineering 

Limited 

Mico 942 

SATE EM SEC 

Mico 942P 

SATE EM SEC 

/USCH 3 






2- w ay emergency 




access 

control 9 

Mico 942P 2- w ay emergency 

SATE EM SEC exit device w ith 



access 

control 9 

Mico 942L 2- w ay emergency 


/USCH 3 solenoid deadlocking 


access 

control 9 

Mico 942L 

SATE EM SEC 

Mico 942 

SATE AD / 

USCH 3 

Mico 942P 

SATE AD / 

USCH 3 

Mico 942L 

SATE AD / 

USCH 3 





access 

control 9 


device w ith 

automatic 

deadlocking 



automatic 

deadlocking 



automatic 

deadlocking 




handle 





handle 




handle 





handle 




handle 

Push plate - 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Push pad - 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 



H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

310 20 Nov 2011



90 Tindall 

Engineering 

Limited 

91 Tindall 

Engineering 

Limited 

92 Tindall 

Engineering 

Limited 

93 Tindall 

Engineering 

Limited 

94 Tindall 

Engineering 

Limited 

95 Tindall 

Engineering 

Limited 

96 Tindall 

Engineering 

Limited 

97 Tindall 

Engineering 

Limited 

98 Tindall 

Engineering 

Limited 

99 Tindall 

Engineering 

Limited 

100 Tindall 

Engineering 

Limited 

Mico 942 

SATE MD / 

USCH 3 

Mico 942P 

SATE MD / 

USCH 3 

Mico 942L 

SATE MD / 

USCH 3 

Mico 942 

/EURO 

ELK 3 

Mico 942P 

/EURO 

ELK 3 

Mico 942L 

/EURO 

ELK 3 

Mico 942 EPC 

EM SEC 

/USCH 3 

Mico 942 EPC 

EM SEC 



deadlocking 








device 


exit device 


exit device 











Mico 942P EPC 2- w ay locking 

EM SEC /USCH system w ith solenoid 

3 




Mico 942P EPC 

EM SEC 






Mico 942L EPC 2- w ay locking 


3 





H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


lever handle 


lever handle 


lever handle 





handle 




handle 





handle 




handle 





handle 

Panic bar S, T, U, V, W, X, 

Y, Z and AA 


Y, Z and AA 


Y, Z and AA 





push plate 





push plate 





push pad 





push pad 





lever handle 



AR, AT and AV 

- 



AR, AT and AV 

- 



AR, AT and AV 

20 Nov 2011 311



101 Tindall 

Engineering 

Limited 

Mico 942L EPC 

EM SEC 









handle 





lever handle 

- 

102 Tindall 

Engineering 

Limited 

103 Tindall 

Engineering 

Limited 

104 Tindall 

Engineering 

Limited 

105 Tindall 

Engineering 

Limited 

106 Tindall 

Engineering 

Limited 

107 Tindall 

Engineering 

Limited 

Mico 942L EPC 

INT AD /USCH 

3 

Mico 942L EPC 

INT AD 

Mico 942 EPC 

INT MD /USCH 

3 

Mico 942 EPC 

INT MD 

Mico 942P EPC 

INT MD /USCH 

3 

Mico 942P EPC 

INT MD 


system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 


None 


None 


None 










and push pad 


and push pad 






AV 

- 






AV 

- 






AV 

- 

108 Tindall 

Engineering 

Limited 

109 Tindall 

Engineering 

Limited 

110 Tindall 

Engineering 

Limited 

111 Tindall 

Engineering 

Limited 

Mico 942L EPC 

INT MD /USCH 

3 

Mico 942L EPC 

INT MD 

Mico 942 EPC 

SATE EM SEC 

/USCH 3 

Mico 942 EPC 

SATE EM SEC 



deadlocking 



deadlocking 












None 





handle 




handle 










AV 

- 

Push plate S, T, U, V, W, X, 

Y, Z and AA 

Push plate - 

312 20 Nov 2011



112 Tindall 

Engineering 

Limited 

113 Tindall 

Engineering 

Limited 

114 Tindall 

Engineering 

Limited 

115 Tindall 

Engineering 

Limited 

116 Tindall 

Engineering 

Limited 

117 Tindall 

Engineering 

Limited 

118 Tindall 

Engineering 

Limited 

119 Tindall 

Engineering 

Limited 

120 Tindall 

Engineering 

Limited 

121 Tindall 

Engineering 

Limited 

122 Tindall 

Engineering 

Limited 

123 Tindall 

Engineering 

Limited 

Mico 942P EPC 

SATE EM SEC 

/USCH 3 





access 

control 9 

Mico 942P EPC 2- w ay emergency 




access 

control 8 

Mico 942L EPC 2- w ay emergency 




access 

control 9 

Mico 942L EPC 

SATE EM SEC 

Mico 942 EPC 

SATE AD / 

USCH 3 

Mico 942P EPC 

SATE AD / 

USCH 3 

Mico 942L EPC 

SATE AD / 

USCH 3 

Mico 942 EPC 

SATE MD / 

USCH 3 





access 

control 9 


device w ith 

automatic 

deadlocking 



automatic 

deadlocking 



automatic 

deadlocking 



deadlocking 

Mico 942P EPC 2-w ay emergency 

SATE MD / exit device w ith 

USCH 3 manual deadlocking 

Mico 942L EPC 2-w ay emergency 

SATE MD / exit device w ith 

USCH 3 manual deadlocking 

Mico 942-3 

/ELK 3 

Mico 942-3 


device 


device 





handle 




handle 





handle 




handle 


Y, Z and AA 

Push pad - 


Y, Z and AA 



Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


H, I, J, K, L, M, N, 

O, P, Q and R 


20 Nov 2011 313



124 Tindall 

Engineering 

Limited 

125 Tindall 

Engineering 

Limited 

126 Tindall 

Engineering 

Limited 

127 Tindall 

Engineering 

Limited 

128 Tindall 

Engineering 

Limited 

Mico 942-3P 

/ELK 3 

Mico 942-3P 

Mico 942-3L 

/ELK 3 

Mico 942-3L 

Mico 942-3 

EM SEC 

/USCH 3 


exit device 


exit device 


exit device 


exit device 







H, I, J, K, L, M, N, 

O, P, Q and R 



H, I, J, K, L, M, N, 

O, P, Q and R 






handle 





push plate 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

129 Tindall 

Engineering 

Limited 

Mico 942-3 

EM SEC 









handle 





push plate 

- 

130 Tindall 

Engineering 

Limited 

Mico 942-3P 3- w ay locking 


3 








handle 





push pad 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

131 Tindall 

Engineering 

Limited 

Mico 942-3P 

EM SEC 









handle 





push pad 

- 

132 Tindall 

Engineering 

Limited 

Mico 942-3L 3- w ay locking 


3 








handle 





lever handle 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

133 Tindall 

Engineering 

Limited 

Mico 942-3L 

EM SEC 









handle 





lever handle 

- 

134 Tindall 

Engineering 

Limited 

Mico 942-3L 

INT AD /USCH 

3 


system w ith 

automatic 

deadlocking 

Key and lever handle Thumb turn and lever 

handle 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

314 20 Nov 2011



135 Tindall 

Engineering 

Limited 

136 Tindall 

Engineering 

Limited 

137 Tindall 

Engineering 

Limited 

138 Tindall 

Engineering 

Limited 

139 Tindall 

Engineering 

Limited 

140 Tindall 

Engineering 

Limited 

141 Tindall 

Engineering 

Limited 

142 Tindall 

Engineering 

Limited 

143 Tindall 

Engineering 

Limited 

144 Tindall 

Engineering 

Limited 

145 Tindall 

Engineering 

Limited 

Mico 942-3L 

INT AD 


MD /USCH 3 


MD 

Mico 942-3P 

INT MD /USCH 

3 

Mico 942-3P 

INT MD 

Mico 942-3L 

INT MD /USCH 

3 

Mico 942-3L 

INT MD 

Mico 942-3 

SATE EM SEC 

/USCH 3 

Mico 942-3 

SATE EM SEC 

Mico 942-3P 

SATE EM SEC 

/USCH 3 

Mico 942-3P 

SATE EM SEC 


system w ith 

automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 















access 

control 9 





access 

control 9 

None 

Key (via USCH 3) 


None 


None 


None 





handle 




handle 





handle 




handle 

Thumb turn and lever 

handle 






and push pad 


and push pad 





- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

- 

Push plate A, B, C, D, E, F, G, 

H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Push plate - 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 

Push pad - 

20 Nov 2011 315



146 Tindall 

Engineering 

Limited 

147 Tindall 

Engineering 

Limited 

148 Tindall 

Engineering 

Limited 

149 Tindall 

Engineering 

Limited 

150 Tindall 

Engineering 

Limited 

151 Tindall 

Engineering 

Limited 

152 Tindall 

Engineering 

Limited 

153 Tindall 

Engineering 

Limited 

154 Tindall 

Engineering 

Limited 

155 Tindall 

Engineering 

Limited 

156 Tindall 

Engineering 

Limited 

157 Tindall 

Engineering 

Limited 

Mico 942-3L 3- w ay emergency 




access 

control 9 

Mico 942-3L 

SATE EM SEC 

Mico 942-3 

SATE AD / 

USCH 3 

Mico 942-3P 

SATE AD / 

USCH 3 

Mico 942-3L 

SATE AD / 

USCH 3 

Mico 942-3 

SATE MD / 

USCH 3 

Mico 942-3P 

SATE MD / 

USCH 3 

Mico 942-3L 

SATE MD / 

USCH 3 

Mico 942-3 

/EURO ELK 3 

Mico 942-3P 

/EURO ELK 3 

Mico 942-3L 

/EURO ELK 3 

Mico 942-3 

EPC EM SEC 

/USCH 3 





access 

control 9 


device w ith 

automatic 

deadlocking 



automatic 

deadlocking 



automatic 

deadlocking 



deadlocking 








device 


exit device 


exit device 










handle 




handle 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 



H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


H, I, J, K, L, M, N, 

O, P, Q, R, AW, 


BB and BC 


Y, Z and AA 


Y, Z and AA 


Y, Z and AA 





handle 





push plate 



AR, AT and AV 

316 20 Nov 2011



158 Tindall 

Engineering 

Limited 

159 Tindall 

Engineering 

Limited 

Mico 942-3 

EPC EM SEC 

Mico 942-3P 

EPC EM SEC 

/USCH 3 














handle 





handle 





push plate 





push pad 

- 



AR, AT and AV 

160 Tindall 

Engineering 

Limited 

Mico 942-3P 

EPC EM SEC 









handle 





push pad 

- 

161 Tindall 

Engineering 

Limited 

Mico 942-3L 

EPC EM SEC 

/USCH 3 










handle 





lever handle 



AR, AT and AV 

162 Tindall 

Engineering 

Limited 

Mico 942-3L 

EPC EM SEC 









handle 





lever handle 

- 

163 Tindall 

Engineering 

Limited 

164 Tindall 

Engineering 

Limited 

165 Tindall 

Engineering 

Limited 

166 Tindall 

Engineering 

Limited 

167 Tindall 

Engineering 

Limited 

Mico 942-3L 

EPC INT AD 

/USCH 3 

Mico 942-3L 

EPC INT AD 

Mico 942-3 

EPC INT MD 

/USCH 3 

Mico 942-3 

EPC INT MD 

Mico 942-3P 

EPC INT MD 

/USCH 3 


system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 


None 


None 











and push pad 






AV 

- 






AV 

- 






AV 

20 Nov 2011 317



168 Tindall 

Engineering 

Limited 

169 Tindall 

Engineering 

Limited 

170 Tindall 

Engineering 

Limited 

171 Tindall 

Engineering 

Limited 

172 Tindall 

Engineering 

Limited 

173 Tindall 

Engineering 

Limited 

174 Tindall 

Engineering 

Limited 

175 Tindall 

Engineering 

Limited 

176 Tindall 

Engineering 

Limited 

177 Tindall 

Engineering 

Limited 

178 Tindall 

Engineering 

Limited 

Mico 942-3P 

EPC INT MD 

Mico 942-3L 

EPC INT MD 

/USCH 3 

Mico 942-3L 

EPC INT MD 

Mico 942-3 

EPC SATE EM 

SEC /USCH 3 

Mico 942-3 

EPC SATE EM 

SEC 

Mico 942-3P 

EPC SATE EM 

SEC /USCH 3 

Mico 942-3P 

EPC SATE EM 

SEC 



deadlocking 



deadlocking 



deadlocking 















access 

control 9 





access 

control 9 

Mico 942-3L 3- w ay emergency 

EPC SATE EM exit device w ith 

SEC /USCH 3 solenoid deadlocking 


access 

control 9 

Mico 942-3L 

EPC SATE EM 

SEC 





access 

control 9 

Mico 942-3 3-w ay panic exit 

EPC SATE AD device w ith 

/ USCH 3 automatic 

deadlocking 


EPC SATE AD exit device w ith 


deadlocking 

None 


None 





handle 




handle 





handle 




handle 





handle 




handle 


and push pad 





- 






AV 

- 

Push plate S, T, U, V, W, X, 

Y, Z and AA 

Push plate - 


Y, Z and AA 

Push pad - 


Y, Z and AA 



Y, Z and AA 


Y, Z and AA 

318 20 Nov 2011



179 Tindall 

Engineering 

Limited 

180 Tindall 

Engineering 

Limited 

181 Tindall 

Engineering 

Limited 

182 Tindall 

Engineering 

Limited 

183 Tindall 

Engineering 

Limited 

184 Bradbury 

Security 



EPC SATE AD exit device w ith 


deadlocking 

Mico 942-3 3-w ay panic exit 

EPC SATE MD device w ith manual 

/ USCH 3 deadlocking 


EPC SATE MD exit device w ith 

/ USCH 3 manual deadlocking 


EPC SATE MD exit device w ith 

/ USCH 3 manual deadlocking 

HSTB Tw o surface 

mounted drop bolts 

- Tw o surface 



Y, Z and AA 


Y, Z and AA 


Y, Z and AA 


Y, Z and AA 

None 

None 

Surface mounted 

drop bolts 


drop bolts 

- 

- 


Reference 

A Abloy Protec CY201 PT Scandinavian Oval 

B Abloy Disklock Pro CY201 DP Scandinavian Oval 

C Abloy Protec Cliq CY201 Scandinavian Oval 

D AMS CL-OVLD Scandinavian Oval 

E ASSA 4401dp Scandinavian Oval 

F ASSA 4401 Cliq Scandinavian Oval 

G ASSA 4407dp Scandinavian Oval 

H ASSA 4407 Cliq Scandinavian Oval 

I ASSA 4801 Scandinavian Oval 

J ASSA 4807 Scandinavian Oval 

K ASSA C5801 Scandinavian Oval 

L ASSA C5807 Scandinavian Oval 

M ASSA Tw in 7601 Scandinavian Oval 

N ASSA Tw in 7607 Scandinavian Oval 

O Kaba K20 Scandinavian Oval 

P Kaba Quattro PluS Scandinavian Oval 

Q Locken CL-PL2WR Scandinavian Oval 

R Medeco M3-ARX Scandinavian Oval 

S ASSA 44M23 Europrofile single cylinder 

T Abloy CY307 Protec Europrofile single cylinder 

U Abloy CY307 Disclock Pro Europrofile single cylinder 

V Abloy CY307 Protec Cliq Europrofile single cylinder 

W ASSA 4823 Europrofile single cylinder 

X ASSA C5823 Europrofile single cylinder 

Y ASSA 7623 Europrofile single cylinder 

Z Medico M3 ARX Europrofile single cylinder 

AA KABA Quattro PluS Europrofile single cylinder 

20 Nov 2011 319



AB ISEO R6 Europrofile double cylinder (key:key) 

AC Abloy Protec CY304 Europrofile double cylinder (key:key) 

AD Abloy Protec Cliq CY304 Europrofile double cylinder (key:key) 

AE Abloy Protec CY305 Europrofile double cylinder (key:thumbturn) 

AF Abloy Protec Cliq CY305 Europrofile double cylinder (key:thumbturn) 

AG Abloy Protec Cliq CY333 Europrofile double cylinder (key:thumbturn) 

AH Abloy Protec CY333 Europrofile double cylinder (key:thumbturn) 

AI ASSA 4422dp Europrofile double cylinder (key:key) 

AJ ASSA 4427dp Europrofile double cylinder (key:thumbturn) 

AK ASSA 44M22 Cliq Europrofile double cylinder (key:key) 

AL ASSA 44M27 Cliq Europrofile double cylinder (key:thumbturn) 

AM ASSA 4822 Europrofile double cylinder (key:key) 

AN ASSA 4827 Europrofile double cylinder (key:thumbturn) 

AO ASSA C5822 Europrofile double cylinder (key:key) 

AP ASSA C5827 Europrofile double cylinder (key:thumbturn) 

AQ ASSA 7622 Europrofile double cylinder (key:key) 

AR ASSA 7627 Europrofile double cylinder (key:thumbturn) 

AS Kaba Quattro PluS Europrofile double cylinder (key:key) 

AT Kaba Quattro PluS Europrofile double cylinder (key:thumbturn) 

AU Medeco M3-ARX Europrofile double cylinder (key:key) 

AV Medeco M3-ARX Europrofile double cylinder (key:thumbturn) 

AW Abloy Protec CY403 Rim 

AX Abloy Protec Cliq CY403 Rim 

AY Kaba Quattro Plus Rim 

AZ Medeco M3-ARX Rim 

BA AMS CL-CA2D Finish Round 

BB ASSA 4857 Round threaded 

BC ASSA C5857 Round threaded 

Accessories 11 

Accessory 

Flat sill 12 

Low profile aluminium sill 12 

No sill 12 

13, 14, 15 

Vision panel 

Description 

3 mm flat plate sill 

Low profile aluminium sill 

No sill 

356 mm high by 203 mm w ide vision panel incorporating a 45.04 mm thick specialist laminated 

double glazed security glazing unit 






security glass 





Notes: 

1. When fitted with compatible lock option 1 the security rating applies to doorsets with the locking mechanisms fully engaged, i.e. in 

optimum locked condition. The single leaf doorset achieves Security Rating 1 when left in the minimum locked condition, i.e. when the 

key is turned once and removed. The double doorset also achieves Security Rating 1 when left in the minimum locked condition, i.e. 

only one surface mounted drop bolt on the passive leaf engaged and the key on the active leaf thrown once and removed. 

2. When fitted with compatible lock option 2 the security rating is also achieved by the doorset when in the minimum locked condition, 

i.e. when both surface mounted drop bolts on the passive leaf are disengaged. 

3. When fitted with the Mico compatible lock options 3 to182 the security rating applies to doorsets with the locking mechanisms fully 

engaged, i.e. in optimum locked condition. The single leaf and double leaf doorsets achieve Security Rating 1 when left in the 

minimum locked condition. 

4. The M2M3 double leaf doorsets can be produced with leafs of unequal width. The maximum width of both leafs is 1100 mm. The 

minimum width of the active leaf is 750 mm. The minimum width of the passive leaf is 400 mm. 



panic or emergency exit device unless the deadlock is automatically operated by the action of the panic or emergency device. For 

320 20 Nov 2011



further information, please refer to the appropriate standards for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 

respectively. 

6. Although outside the scope of LPS 1175: Issue 7, special consideration should be paid to the use of single operating panic or 

emergency exit devices. This is because it is generally accepted that when two panic or emergency exit devices are fitted to double 

doorsets the operation of either device should disengage simultaneously such that both leafs can open. For further information, 

please refer to the appropriate standard for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 respectively. 

7. The two-way locking systems used on the passive leaf of double doorsets shall incorporate identical internal operation devices to 

those on the locking systems used on the active leaf. 

8. Certification does not cover the use of locks other than those listed. Utilisation of unlisted locks may affect the level of security offered 

by the doorset. 





and system configurations that may be used with these locking systems is “infinite”. It is therefore recommended that Ascot Doors 

Limited satisfy themselves that the components are either resistant to mechanical and other forms of tampering/abuse, or that they 

are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may cause the 

locking system to disengage. 

11. Certification does not cover the use of vision panels or other accessories that are not listed. Utilisation of other accessories may affect 

the level of security offered by the doorset. 

12. The alternative sill options should not to be fitted to doorsets incorporating panic bars or push pads. 

13. The standard (stepped) sill must always be used on doorsets incorporating either glazed apertures or locking mechanisms 

incorporating single action escape panic exit systems operated by panic bars. 

14. Doorsets fitted with upper and lower glazed apertures should not incorporate hardware operated by a panic bar. 

15. The 45.04 mm thick specialist laminated double glazed security glazing unit should only be used on doorsets fitted with compatible 

lock option 1 and options 3 to 182 incorporating internal key deadlocks. 

C W Fields and Son Limited 

Station Road Industrial Estate, Epworth, Nr. Doncaster, South Yorkshire DN9 1JZ, United Kingdom 

Tel: +44 (0)1427 872368 • Fax: +44 (0)1427 873057 

E-mail: info@cwfields.co.uk • Website: www.cwfields.co.uk 



Product Type 

Name 

Fields 

Security 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Single leaf outward 0.705 2.605 0.382 0.997 2 940a/01 


security 

doorset 

Single leaf outward 0.955 3.055 0.382 0.997 2 940a/02 

over panels 1 


security 

doorset with 

fixed/removable 

Single leaf inward 0.705 2.605 0.382 0.997 2 940a/03 


security 

doorset 

Single leaf inward 0.955 3.055 0.382 0.997 2 940a/04 

over panels 1 


security 

doorset with 


Double leaf outward 


security 

doorset 2 0.705 2.605 0.685 1.915 2 940a/05 

Cert. 

No. 

20 Nov 2011 321



Product 

Name 

Type 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Double leaf outward 0.955 3.055 0.685 1.915 2 940a/06 

over panels 1, 2 


security 

doorset with 


Double leaf inward 0.705 2.605 0.685 1.915 2 940a/07 

doorset 2 


security 

Double leaf inward 


security 

doorset with 


over panels 1, 2 0.955 3.055 0.685 1.915 2 940a/08 

Cert. 

No. 


LPCB Ref. 

No. 

Trade 

Name 

940a/01 Fields 

Security 


Security 


Security 


Security 


Security 


Security 


Security 


Security 


Type 

Active Leaf Passive Leaf 

Single leaf outw ard opening hinged security 1, 2, 3 N/A 

doorset 

Single leaf outw ard opening hinged security 1, 2, 3 N/A 

doorset w ith fixed/removable over panels 1 

Single leaf inw ard opening hinged security 1, 2, 3 N/A 

doorset 

Single leaf inw ard opening hinged security 1, 2, 3 N/A 

doorset w ith fixed/removable over panels 1 

Double leaf outw ard opening hinged security 1, 2, 3 4 

doorset 2 

Double leaf outw ard opening hinged security 1, 2, 3 4 

doorset w ith fixed/removable over panels 1,2 

Double leaf inw ard opening hinged security 1, 2, 3 4 

doorset 2 

Double leaf inw ard opening hinged security 1, 2, 3 4 

doorset w ith fixed/removable over panels 1,2 


322 20 Nov 2011



Compatible 

Locking 

System 

Manufacturer Model Operating Devices 

1 Surelock McGill 

Limited 


Limited 


Limited 


Limited 

External 

Face 

Internal 

Face 

SL325- E1K2O2 PW Electromechanical 

Single action 

lever handle 

access 

control lock 

(fail secure) 

w ith key 

override and 

lever handle 

SL325-E1W Electromechanical 

Single action 

lever handle 

access 

control lock 

(fail secure) 

w ith lever 

handle 

SL315- E1K2O2PW Key and lever Single action 

handle lever handle 

TBFW barrel bolts None Tw o barrel 

bolts 

Compatible 

Cylinders 

A 

A 

A 

N/A 


Cylinder 

Reference 


A Assa C5857 Rim cylinder 

Vision Panels 

Trade 

Name 

Fields 

Security 

Vision Panels 

30 mm w ide by 300 mm high vision 

panels on leafs at least 567 mm w ide. 

Compatible Doorset Configurations 

Single 

Leaf 

Inw ard 

Opening 

Single 

Leaf 

Outw ard 

Opening 

Double 

Leaf 

Inward 

Opening 

Double 

Leaf 

Outward 

Opening 

 

Notes: 

1. The maximum door leaf height is 2558 mm. 

2. The scope of this approval includes double leaf doorsets with equal and unequal leafs. The maximum individual leaf width is 915 mm 

and the minimum individual leaf width is 300 mm. 


11 Landau Way, Darent Industrial Park, Erith, Kent DA8 2LF, United Kingdom 

Tel: +44 (0)1322 332211 • Fax: +44 (0)1322 339582 

E-mail: info@clearwayservices.co.uk • Website: www.clearwayservices.co.uk 


20 Nov 2011 323



Temporary Security Doorset 

Product 

Name 

Configuration Minimum 

Structural 

Opening 

Height 1 

Toreadoor 

Single leaf, 

outward 

opening, 

hinged 

temporary 3 

security 

doorset 

Maximum 

Structural 

Opening 

Height 1 

Minimum 

Structural 

Opening 

Width 1 

Maximum 

Structural 

Opening 

Width 1 

Minimum 

Structural 

Opening 

Depth 2 

Maximum 

Structural 

Opening 

Depth 2 

Security 

Rating 

Cert. 

No. 

(m) (m) (m) (m) (m) (m) 

1.61 1.93 0.37 0.76 0.045 0.25 1 1001a 

4 

Manufacturer Model Type Compatible Opening Devices 



Willenhall M1 Clearw ays 5-lever mortice deadlock Key and handle Key and handle 

Clearw ay Centurion Electronic locking system 5 Keypad Manual actuator 

Notes: 

1. The doorset is available in one fixed size to suit a range of structural opening sizes. 

2. Maximum depth of the aperture within the supporting substrate 6 that the doorset can be fitted within. 

3. The doorset is designed to be fitted to unoccupied properties. 

4. Both locking systems are fitted to the doorset. The security rating was achieved by the doorset with only one lock engaged, i.e. the 

minimum locked condition. The doorset also achieved Security Rating 1 in the optimum locked condition, i.e. with both locks engaged. 

5. The resistance of the electronic locking system to “non-mechanical” attack has not been assessed because it is outside the scope of 

LPS 1175: Issue 7. 

6. The doorset is suitable for installation 7 into timber, brickwork, steel, blockwork, concrete and aluminium substrates. 

7. The doorset should be installed in accordance with the installation instructions ‘Fitting / Fixing instructions for the Toreadoor Keyless 

Door’ dated 13 October 2011. 

Design & Supply Limited 

13 Pant Industrial Estate, Merthyr Tydfil, Mid Glamorgan CF48 2SR, United Kingdom 

Tel: +44 (0)1685 350114 • Fax: +44 (0)1685 723276 

E-mail: dsl@designandsupply.co.uk 



Product Name Type Minimum 

Structural 

Opening 

Height 

(m) 

Desray Single leaf outward opening 

Maximum 

Structural 

Opening 

Height 

(m) 

Minimum 

Structural 

Opening 

Width 

(m) 

Maximum 

Structural 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

1.8 2.2 0.75 1.1 2 694b/01 

hinged security doorset 

Double leaf outward opening 1.8 2.2 1.5 2.5 2 694b/02 

hinged security doorset 1 


LPCB Ref. No. Product Name Type 

694b/01 Desray Single leaf outw ard 



694b/02 Desray Double leaf outw ard 



Com patible Locking System 

Active Leaf Passive Leaf 

1, 2, 3, 4, 6, 7, 8 - 

1, 2, 3, 4, 6, 7, 8 5 2 , 9 

324 20 Nov 2011




Compatible 

Locking 

Systems 

Manufacturer 

Model 

Type 

Compatible Operating 

Devices 


1 Assa 765 Sash lock Key and lever Key and lever A 

handle handle 

2 Assa 765 Sash lock Key and lever Thumbturn and B 


3 Assa 2788 Dead lock Key Key A 

4 Assa 2788 Dead lock Key Thumbturn B 

5 Exidor 802 Tw o point panic exit None Panic bar N/A 

device 

6 Exidor 803 Three point panic exit None Panic bar N/A 

device 3 

7 Exidor 803 w ith 809 Three point panic exit 

device w ith outside 

access device 3 

Key via Exidor 

809 outside 

access device 

Panic bar C 




Key via Exidor 

810 outside 

access device 

Panic bar 

Compatible 

Cylinder 

9 Exidor HS923/10 Tw o tow er bolts None Tow er bolts N/A 



Reference 

A Assa C5802 Double oval cylinder (key:key) 

Accessories 

B Assa C5801 Double oval cylinder (key:thumbturn) 

C Zone 1850 Single europrofile cylinder 

Accessory Description EXECDOOR doorsets 

Sherman vision panel 4 40.5 mm thick vision panels of maximum dimensions 400 mm by 

400 mm. These may either be located central to the w idth of the 

leaf or offset from leading edge by 150 mm. 

Chieftain vision panel 4 27.8 mm thick vision panels of maximum dimensions 400 mm by 

400 mm. These may either be located central to the w idth of the 

leaf or offset from leading edge by 150 mm. 

AB26 vision panel 27 mm thick vision panels of maximum dimensions 400 mm by 400 

mm. These may either be located central to the w idth of the leaf 

or offset from leading edge by 150 mm. 

The following table confirms which combinations of vision panel and locking system may be used together. 

Com patible Locking 

Compatible Vision Panels 

Systems 

1 Sherman, Chieftain and AB26 

Notes: 

2 Sherman and AB26 








C 

694b/01 694b/02 

 

 

 

 

 

 

20 Nov 2011 325



1. Double leaf Desray doorsets may incorporate leafs of equal or unequal width. Leafs of unequal width will comprise of an active leaf 

exactly twice as wide as the passive leaf. The maximum leaf width is 1350 mm and the minimum leaf width is 500 mm. 

2. This locking system may only be used on the passive leaf and then only if locking systems 6, 7 or 8 are used on the active leaf. 

3. Locking systems 6, 7 and 8 may not comply with fire escape regulations relating to potential panic situations if fitted to double leaf 

doorsets. This is because activation of the device on one leaf may not necessarily release the other leaf and in some cases may not 

release the leaf to which it is fitted. 

4. These vision panels incorporate obscurable panels controlled by a handle on the protected side of the doorset. 


Millen Road, Sittingbourne, Kent ME10 2AA, United Kingdom 

Tel: +44 (0)1795 476161 • Fax: +44 (0)1795 422463 

E-mail: martin_roberts@eu.irco.com • Website: www.irmartinroberts.co.uk 




Clear 

Opening 

Height 

(m) 

Martin Roberts Single leaf, outward opening 

SD5003 Range 

Martin Roberts 

SD5001 


Single leaf, outward opening 

hinged security doorsets 

Single leaf, inward opening 


Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

0.951 3.049 0.503 1.322 3 322a/01 

0.951 3.049 0.503 1.322 1 322a/02 

0.951 2.25 0.503 1.322 1 


LPCB Ref. No. Trade Name Type Compatible Locking Systems 

322a/01 Martin Roberts SD5003 Single leaf, outw ard opening hinged security doorset 1, 2, 4, 6, 7, 8, 9, 10, 11, 12 and 13 

322a/02 Martin Roberts SD5001 1 


Single leaf, outw ard opening hinged security doorset 5 

Single leaf, inw ard opening hinged security doorset 3 

Option Locking System Type Compatible External and Internal Operating Devices 

External 

Internal 

1 Assa 765 Sash Lock Key via an Assa 6501 single 

cylinder or an Assa 6502 double 

cylinder 

Key plus lever handle 

or 

Key plus thumb-turn 

2 Assa 500/9 Mortice Locking Latch Key via an Assa 6501 single 

cylinder 

Assa Mico 944 panic latch 

or 

Briton 379 panic operator 

or Lever handle 

3 Assa 1520 Escape Sash Lock Key via an Assa 4801 single 

cylinder 

or 

Key via an Assa 4802 double 

cylinder 

Assa 6650C solid brass handle 

plus either: 

Assa 6256 thumbturn 

or 


cylinder 

4 Assa 8761 Emergency Nightlatch Key via an Assa 6501 single 

cylinder 


or 


or 

Lever handle 

326 20 Nov 2011



5 Assa 8761 Emergency Nightlatch Key via an Assa 4801 single Assa 640 solid brass handle 

cylinder 

6 Assa 9788 Mortice Deadlock Key via an Assa 6501 single 

cylinder or an Assa 6502 double 

cylinder 

Key 

or 

Thumb-turn 

7 2 Assa 8761 

and 

Assa 9788 

Emergency Nightlatch 

and 

Mortice Deadlock 

Tw o separate keys via Assa 

6501 or Assa 6502 cylinders 

Combination of either: 

Assa Mico 944 panic latch, 

Briton 379 panic operator or 

Lever handle, and either: 

key or thumb-turn 

8 Assa 9788 (Tw o fitted) Mortice Deadlocks Key via an Assa 6501 single or 

Assa 6502 double cylinder 

9 Security Engineering plc 

SI1216 


SI1233 


SI1241 

12 2 Security Engineering plc 

SI 1233 and SI 1241 

Sash Lock 


Mortice Deadlock 


and Mortice Deadlock 

Key via a Buga 4600 single 

cylinder or a Buga 4610 double 

cylinder 


cylinder 


cylinder or a Buga 4610 double 

cylinder 

Tw o separate keys via Buga 

4600 or Buga 4610 cylinders 

13 SI 1241 (tw o fitted) Mortice Deadlocks Key via a Buga 4600 single or 

Buga 4610 double cylinder 

Tw o keys 

or 

Tw o thumb-turns 

or 

One key and one thumb-turn 

Key plus lever handle 

or 

Key plus thumb-turn 


or 


or 

Lever handle 

Key 

or 

Thumb-turn 

Combination of either: 

Assa Mico 944 panic latch, 

Briton 379 panic operator or 

Lever handle, and either: 

key or thumb-turn 

Tw o keys 

or 

Tw o thumb-turns 

or 

One key and one thumb-turn 

Notes: 

1. The Martin Roberts SD5001 also meets the requirements of PAS23-1:1999 and PAS24-1:1999. For further information, please refer 

to entries in sections on PAS23-1 and PAS24-1 relating to LPCB certificates 322b and 322c respectively. 

2. Although outside the scope of LPS1175: Issue 5, special consideration should be paid to the use of the Assa 9788 Mortice Deadlock 

in combination with the Assa 8761 Emergency Nightlatch or the SI1241 Mortice Deadlock in combination with the SI1233 Emergency 

Nightlatch. This is because it is generally not acceptable to separately deadlock a doorset that is fitted with a panic or emergency exit 

device unless the deadlock is automatically operated by the action of the panic or emergency device. For further information, please 

refer to the appropriate standards for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 respectively. 



Product Name Doorset Configuration Minimum 

Clear 

Opening 

Height 

(m) 

SD5002-01 

Single plain leaf 

outward opening 

doorset 

SD5002-02 Double plain leaf 


doorset 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

1.7 2.25 0.7 1.2 2 322d/01 

1.9 2.25 1.4 2.5 2 1 322d/02 


20 Nov 2011 327



Product Name 

Doorset Configuration 


SD5002-01 

SD5002-02 

Single plain leaf outw ard 


Double plain leaf outw ard 


Active Leaf 

Passive Leaf 

1 N/A 

2 3 


Compatible 

Locking Systems 


External 

Face 

1 Briton 5520 Sash lock Key and 

lever handle 


Devices 

Internal 

Face 

Thumbturn 

and lever 

handle 

Compatible 

Cylinders 

CISA 52526-60-0 

double europrofile 

cylinder 

2 CISA 52526-60-0 and 

06453-05-0 

Mortice deadlock 

and sw ing bolts 

Key and 

lever handle 

Thumbturn 

and lever 

handle 

CISA 52526-60-0 

double europrofile 

cylinder 

3 Exidor HS923 Drop bolts N/A N/A N/A 

Note: 

1. In order to provide the certified level of resistance to forced entry, the key must be rotated through 720 degrees, to fully engage the 

bolts before removing it from the cylinder, and both drop bolts must be engaged. Security rating 1 classification prevails if the key is 

only turned once through 360 degrees before removing. 



Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 




Product 

Type 

Name 

Minimum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

LD Series 4 

Single leaf, outward opening hinged 


1.8 0.75 2.25 1.15 4 442a/01 


LPCB Ref. Trade Type Lock Cylinder 

No. Name 

442a/01 LD Series 4 Single leaf hinged outw ard 

opening hinged security doorset 

Surelock McGill C3 3-w ay 

multiple bolting unit 

Abloy 5841 Europrofile single 

cylinder w ith internal thumbturn 


328 20 Nov 2011




Product 

Type 

Name 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

Liddle Series 

3 

Single leaf outward opening 

hinged doorset 

Double leaf 1 outward opening 





Cert. No. Product Name Type Compatible Locking Systems 

442b/01 Liddle Series 3 Single leaf outw ard opening 


442b/02 Liddle Series 3 Double leaf outw ard opening 



Com patible 

Locking 

System 


1 Surelock McGill Stirling EX800 

ST105-0X-W3 


ST115-0X- 

K13O0PW3 

3 Surelock McGill Stirling DL800 

ST103-0X-W3 

4 Surelock McGill Stirling DL800 

ST113-0X- 

K13O0PW3 

Single point surface 

mounted emergency exit 

device 



device w ith external 

access via a cylinder 

protected by an ‘SR3’ 



mounted deadlock 


mounted deadlock w ith 

external access via a 

cylinder protected by an 

‘SR3’ cylinder guard 

Active leaf 

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 

11 

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 

11 


Device 

Passive Leaf 

N/A 

12 

External Internal 

Face Face 

None Lever handle Not applicable 

Key plus lever 

handle 

None 


handle 

Lever handle 

Thumb turn 

plus lever 

handle 

Thumb turn 

plus lever 

handle 

Compatible 

Cylinders 

A, B, C, D, E 

Not applicable 

A, B, C, D, E 

20 Nov 2011 329



5 Surelock McGill Stirling AC800 

ST102-0X-W3 


ST122-0X-W3 


ST122-0X- 

K13O0PW3 


mounted electromechanical 

access 

control lock pow ered by 

12 V, 24 V or 50 V failsecure 

solenoid 2 None Lever handle 

plus access 

control 2 



access 



solenoid 2 



access 



solenoid 2 w ith 

external key override via 

a cylinder protected by 

an ‘SR3’ cylinder guard 

Lever handle 

plus access 

control 2 

Lever handle 

plus either 

key or access 

control 2 

Lever handle 

plus access 

control 2 

Lever handle 

plus access 

control 2 



A, B, C, D, E 


ST105-0X-H3W3 


ST115-OX- 

H3K13O0PW3 


ST125-0X-H3W3 


ST125-0X- 

H3K13O0PW3 

12 Surelock McGill Surelock TA 

tow er bolt 




device 



device w ith external 

access via a cylinder 

protected by an ‘SR3’ 




access 



solenoid 2 



access 



solenoid 2 w ith 

external key override via 

a cylinder protected by 

an ‘SR3’ cylinder guard 

None Push pad Not applicable 


handle 

Lever handle 

plus access 

control 2 

Lever handle 

plus either 

key or access 

control 2 

Push pad 

Push pad 

plus access 

control 2 

Push pad 

plus access 

control 2 

A, B, C, D, E 


A, B, C, D, E 

Tow er bolt 3 - - Not applicable 

Cylinder Reference Manufacturer Model Type 

A Abloy CY403 PT Rim cylinder 

B Abloy CY405 PT Rim cylinder 

C Assa 4857 Rim cylinder 

D Assa C5857 Rim cylinder 

E Kaba KV06.100 Rim cylinder 

Notes: 

1. The scope covers double doorsets formed with two leafs of equal widths. 

330 20 Nov 2011



2. The resistance of the access control locks to ‘non-mechanical’ attack was not assessed as it is outside the scope of LPS1175. 


access control equipment used to operate these locking systems. This is because the scope of access control devices and system 

configurations that may be used with these locking systems is ‘infinite’. It is therefore recommended that customer satisfy themselves 

that the components used are either resistant to mechanical and other forms of tampering/abuse, or that they are suitably protected 

from such tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking system to 

disengage. 

3. Two tower bolts are fitted. 



Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 




Product Name Product Type Minimum 

Height (m) 

Lowrey Level 4 

Single Leaf 

Security Doorset 


Double Leaf 



opening plain leaf 

doorset 

Double leaf 



Maximum Minimum Maximum Security Cert. 

Height (m) Width (m) Width (m) Rating No. 

1.0 2.4 0.6 1.3 4 974d/01 

1.0 2.4 1.2 2.6 4 974d/02 

Manufacturer Locking Device Type Cylinder Approved Product 

(LPCB Ref. No. 974d/..) 

Compatible Locking Devices 1, 2 1 2 

Abloy PL330/25 (V01) HP Padlock Abloy High Profile 

Abloy PL330/25 (V01) EX Padlock Abloy Exec 

Abloy PL330/25 (V01) PT Padlock Abloy Protec 



Abloy PL340/25 (V01) PT Padlock Protec 

Abloy PL342 (V01) HP Padlock Abloy High Profile 

Abloy PL342 (V01) EX Padlock Abloy Exec 

Abloy PL342 (V01) PT Padlock Abloy Protec 



Abloy PL350/25 (V01) PT Padlock Abloy Protec 

Kaba 

Kaba K18 w ith 11 mm open Padlock Kaba K20-C5 

shackle (Item No. K180010-SS) 

Kaba Kaba K2010 Padlock Kaba K20 (Armoured) 3 

Pickersgill-Kaye Kaye-Rota L8637-901 ST Padlock Kaba K20 (Armoured) 3 

Pickersgill-Kaye Kaye-Rota L8637-902 SE Padlock Kaba K20 (Armoured) 3 

Notes: 



2. The ‘user friendliness’ of employing the padlocks listed has not been assessed as this is beyond the scope of LPS 1175: Issue 7. 

3. The torque resistant version of the Kaba K20 cylinder must be fitted to these padlocks in place of the standard Kaba 20 cylinders. 

4. The Lowrey plain leaf doorsets are approved when installed in accordance with the instructions detailed on Lowrey document 

E-INST004 (Issue 8). 

20 Nov 2011 331



Powershield Doors Limited 

21 Ferguson Drive, Knockmore Hill Industrial Park, Lisburn, Northern Ireland BT28 2EX, United Kingdom 

Tel: +44 (0)28 9266 2200 • Fax: +44 (0)28 9260 3600 

E-mail: sales@powershield.co.uk • Website: www.powershield.co.uk 




Structural 

Opening 

Height 

(m) 

Powershield Class Single leaf, outward opening 

3 single 

Powershield Class 

3 double 


4 single 


4 double 


Double leaf, outward 


Maximum 

Structural 

Opening 

Height 

(m) 

Minimum 

Structural 

Opening 

Width 

(m) 

Maximum 

Structural 

Opening 

Width 

(m) 

Security 

Rating 1 

Cert. 

No. 

1.8 2.4 0.75 1.2 3 852a/01 

1.8 2.4 1.4 2.4 3 852a/02 

Single leaf, outward opening 1.8 2.4 0.75 1.2 4 852a/03 


Double leaf, outward 1.8 2.4 1.4 2.4 4 852a/04 

doorset 2 



LPCB Ref. 

No. 

852a/01 Powershield Class 3 

single 

Trade Name Type Compatible Locking Systems 



Active Leaf 

Passive Leaf 

1 to 58 N/A 


double 

Double leaf, outward opening 


1 to 58 67 


single 



11, 13, 15, 17 , 40, 42, 44, 46 

59, 60, 61, 62, 63, 64, 65 and 

66 

N/A 


double 



11, 13, 15, 17 , 40, 42, 44, 46 

59, 60, 61, 62, 63, 64, 65 and 

66 

67 


Compatible 

Locking 

Systems 

Model 4 Type Operation 

Entry 

Exit 

External Cylinder 

1 MICO 942-3 / 

EURO ELK 3 

2 MICO 942-3P / 

EURO ELK 3 

3 MICO 942-3L / 

EURO ELK 3 

4 MICO 942-3 

EPC EM SEC / 

HSCH 3 

3-way panic exit 

device 

3-way emergency exit 

device 


device 

3-way locking system 

with solenoid 

deadlock and 

electromechanical 


powdered by 12v. 

Key via EURO ELK 3 Panic exit push plate A, B, C, D, E and F 

Key via EURO ELK 3 Push pad A, B, C, D, E and F 

Key via EURO ELK 3 Lever handle A, B, C, D, E and F 

Access control system (e.g. 

key pad or swipe card) not 

specified 3 or key override 

via Europrofile cylinder 

within the HSCH3 cylinder 

guard and lever handle 


control and thumb 

turn override via 

Europrofile cylinder 

with push plate 

A, B, C, D, E and F 

332 20 Nov 2011



5 MICO 942-3 

EPC EM SEC 


with solenoid 

deadlock and 






specified 3 and lever handle 

Access control and 

thumb turn override 

via Europrofile 

cylinder with push 

plate 

- 

6 MICO 942-3P 

EPC EM SEC / 

HSCH 3 


with solenoid 

deadlock and 













cylinder with push pad 


7 MICO 942-3P 

EPC EM SEC 


with solenoid 

deadlock and 










cylinder with push pad 

- 

8 MICO 942-3L 

EPC EM SEC / 

HSCH 3 


with solenoid 

deadlock and 













cylinder with lever 

handle 


9 MICO 942-3L 

EPC EM SEC 


with solenoid 

deadlock and 











handle 

- 

10 MICO 942-3L 

EPC INT AD / 

HSCH 3 


with automatic 

deadlocking. 

Europrofile cylinder, within 

the HSCH 3 and lever 

handle 


(Key or thumb turn) 



11 MICO 942-3L 

EPC INT AD 



deadlocking. 

None 


(Key or thumb 

turn)and lever handle 

- 

12 MICO 942-3 

EPC INT MD / 

HSCH 3 

3-way locking system Europrofile cylinder, within 

with manual deadlock. the HSCH 3 and lever 

handle 



and panic exit push 

plate 


13 MICO 942-3 

EPC INT MD 

3-way locking system None 

with manual deadlock. 




plate 

- 

20 Nov 2011 333



14 MICO 942-3P 

EPC INT MD / 

HSCH 3 

15 MICO 942-3P 

EPC INT MD 

16 MICO 942-3L 

EPC INT MD / 

HSCH 3 

17 MICO 942-3L 

EPC INT MD 

18 MICO 942-3 

EPC SATE EM 

SEC / HSCH 3 



handle 





handle 




device with solenoid 


access 

control powered by 

12v. 









and push pad 



and push pad 







Panic exit push plate 


- 


- 


19 MICO 942-3 

EPC SATE EM 

SEC 




access 


12v. 




Panic exit push plate - 

20 MICO 942-3P 

EPC SATE EM 

SEC / HSCH 3 




access 


12v. 







Push pad 


21 MICO 942-3P 

EPC SATE EM 

SEC 




access 


12v. 

Access control system (e.g. Push pad - 



22 MICO 942-3L 

EPC SATE EM 

SEC / HSCH 3 




access 


12v. 







Lever handle 


23 MICO 942-3L 

EPC SATE EM 

SEC 




access 


12v. 





24 MICO 942-3 

EPC SATE AD / 

HSCH 3 


device with automatic 

deadlock. 



handle 



334 20 Nov 2011



25 MICO 942-3P 

EPC SATE AD / 

HSCH 3 

26 MICO 942-3L 

EPC SATE AD / 

HSCH 3 



deadlock. 



deadlock. 

27 MICO 942-3 3-way panic exit 

EPC SATE MD / device with manual 

HSCH 3 deadlock. 

28 MICO 942-3P 3-way emergency exit 



29 MICO 942-3L 3-way emergency exit 



30 MICO 942-3 / 

ELK 3 

31 MICO 942-3P / 

ELK 3 

32 MICO 942-3L / 

ELK 3 

33 MICO 942-3 EM 

SEC / HSCH 3 


device 


device 


device 


with solenoid 

deadlock and 






handle 



handle 



handle 



handle 



handle 

Push pad 

Lever handle 


Push pad 

Lever handle 






Key via ELK 3 Panic exit push plate K, L,M,N, O, P, Q, R 

and T 

Key via ELK 3 Push pad K, L,M,N, O, P, Q, R 

and T 

Key via ELK 3 Lever handle K, L,M,N, O, P, Q, R 

and T 




via Scandinavian oval 

cylinder within the HSCH3 

cylinder guard and lever 

handle 


control and thumb 

turn override via 

Scandinavian oval 

cylinder with push 

plate 

G, H, I, J, K, L, M, N 

and P 

34 MICO 942-3 EM 

SEC 


with solenoid 

deadlock and 









via Scandinavian 

oval cylinder with 

push plate 

- 

35 MICO 942-3P 

EM SEC / 

HSCH 3 


with solenoid 

deadlock and 










handle 





push pad 

G, H, I, J, K, L, M, N 

and P 

36 MICO 942-3P 

EM SEC 


with solenoid 

deadlock and 











push pad 

- 

37 MICO 942-3L 

EM SEC / 

HSCH 3 


with solenoid 

deadlock and 










handle 





handle 

G, H, I, J, K, L, M, N 

and P 

20 Nov 2011 335



38 MICO 942-3L 

EM SEC 


with solenoid 

deadlock and 











handle 

- 

39 MICO 942-3L 

INT AD / HSCH 

3 

40 MICO 942-3L 

INT AD 

41 MICO 942-3 INT 

MD / HSCH 3 



deadlocking. 



deadlocking. 

Scandinavian oval cylinder, 

within the HSCH 3 and 

lever handle 

None 

3-way locking system Scandinavian oval cylinder, 

with manual deadlock. within the HSCH 3 and 

lever handle 


cylinder (Key or 

thumb turn) and lever 

handle 



thumb turn)and lever 

handle 



thumb turn) and panic 

exit push plate 

G, H, I, J, K, L, M, N 

and P 

- 

G, H, I, J, K, L, M, N 

and P 

42 MICO 942-3 INT 

MD 







- 

43 MICO 942-3P 

INT MD / HSCH 

3 

44 MICO 942-3P 

INT MD 

45 MICO 942-3L 

INT MD / HSCH 

3 

46 MICO 942-3L 

INT MD 



lever handle 





lever handle 





thumb turn) and push 

pad 




pad 




handle 




handle 

G, H, I, J, K, L, M, N 

and P 

- 

G, H, I, J, K, L, M, N 

and P 

- 

336 20 Nov 2011



47 MICO 942-3 3-way panic exit 

SATE EM SEC / device with solenoid 

HSCH 3 deadlock and electromechanical 

access 


12v. 







handle 


G, H, I, J, K, L, M, N 

and P 

48 MICO 942-3 

SATE EM SEC 




access 


12v. 




Panic exit push plate - 

49 MICO 942-3P 

SATE EM SEC / 

HSCH 3 




access 


12v. 







handle 

Push pad 

G, H, I, J, K, L, M, N 

and P 

50 MICO 942-3P 

SATE EM SEC 




access 


12v. 




Push pad - 

51 MICO 942-3L 

SATE EM SEC / 

HSCH 3 




access 


12v. 







handle 

Lever handle 

G, H, I, J, K, L, M, N 

and P 

52 MICO 942-3L 

SATE EM SEC 




access 


12v. 





20 Nov 2011 337



53 MICO 942-3 

SATE AD / 

HSCH 3 



deadlock. 



lever handle 


G, H, I, J, K, L, M, N 

and P 

54 MICO 942-3P 

SATE AD / 

HSCH 3 



deadlock. 



lever handle 

Push pad 

G, H, I, J, K, L, M, N 

and P 

55 MICO 942-3L 

SATE AD / 

HSCH 3 



deadlock. 



lever handle 

Lever handle 

G, H, I, J, K, L, M, N 

and P 

56 MICO 942-3 

SATE MD / 

HSCH 3 


device with manual 

deadlock. 



lever handle 


G, H, I, J, K, L, M, N 

and P 

57 MICO 942-3P 

SATE MD / 

HSCH 3 



deadlock. 



lever handle 

Push pad 

G, H, I, J, K, L, M, N 

and P 

58 MICO 942-3L 

SATE MD / 

HSCH 3 



deadlock. 



lever handle 

Lever handle 

G, H, I, J, K, L, M, N 

and P 

59 MICO 942-3L 

EPC INT AD / 

HSCH 4 



deadlocking. 

Europrofile cylinder within 


handle 





60 MICO 942-3 

EPC INT MD / 

HSCH 4 

61 MICO 942-3P 

EPC INT MD / 

HSCH 4 

62 MICO 942-3L 

EPC INT MD / 

HSCH 4 

63 MICO 942-3L 

INT AD / HSCH 

4 

64 MICO 942-3 INT 

MD / HSCH 4 

3-way locking system Europrofile cylinder within 


handle 



handle 



handle 



deadlocking. 

Scandinavian oval cylinder 


lever handle 

3-way locking system Scandinavian oval cylinder 


lever handle 




plate 



and push pad 







handle 








G, H, I, J, K, L, M, N 

and P 

G, H, I, J, K, L, M, N 

and P 

65 MICO 942-3P 

INT MD / HSCH 

4 

66 MICO 942-3L 

INT MD / HSCH 

4 


barrel bolts 




lever handle 



lever handle 




pad 




handle 

G, H, I, J, K, L, M, N 

and P 

G, H, I, J, K, L, M, N 

and P 

- - - 

338 20 Nov 2011




A Abloy Protec CY304 Double Europrofile cylinder (Key:Key or Key:Thumbturn) 

B Abloy Disclock Pro CY304 Double Europrofile cylinder (Key:Key or Key:Thumbturn) 

C ASSA Twin 7622 Double Europrofile cylinder (Key:Key or Key:Thumbturn) 

D ASSA C5822 Double Europrofile cylinder (Key:Key or Key:Thumbturn) 

E ASSA 4822 Double Europrofile cylinder (Key:Key or Key:Thumbturn) 

F Kaba Quattro S Euro Double Europrofile cylinder (Key:Key or Key:Thumbturn) 


H ASSA Twin 7607 Half Scandinavian oval mechanical cylinder 







O Abloy Disclock Pro CY201DPHalf Scandinavian oval mechanical cylinder 


Q ASSA Twin 7601 Half Scandinavian oval mechanical cylinder 


T ASSA 4401 Half Scandinavian oval mechanical cylinder 

Notes: 

1. This security rating prevails when the doorsets are locked in the optimum locked condition. The following locking configurations 

incorporate a manual deadlock mechanism: 13, 15, 17, 42, 44 and 46. If the door is closed and the deadlock mechanism is not 

engaged then a minimum locked condition exists. In this condition the doorsets achieve a minimum of a Security Rating 1. 

2. The scope of this approval covers double leaf doorsets with equal leafs. Double doorsets with unequal leafs are not covered by this 

approval. 

3. The resistance of the access control locks to “non-mechanical” attack is not covered by this approval as they were outside the scope 

of LPS 1175. Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and 

performance of any access control equipment that may be used to operate these locking systems. This is because the scope of 

access control devices and system configurations that may be used with these locking systems is “infinite”. It is therefore 

recommended that specifiers’ satisfy themselves that the components used are either resistant to mechanical and other forms of 

tampering/abuse, or that they are suitably protected from such tampering/abuse and are resistant to any environmental 

conditions/interference that may cause the locking system to disengage. 



panic or emergency exit device unless the deadlock is automatically operated by the action of the panic or exit device. Furthermore, 

double doorsets with panic devices fitted to only one leaf do not necessarily suit public areas. For further information, please refer to 

the appropriate standards for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 respectively. 




Tel: +44 (0)1269 851777 • Fax: +44 (0)1269 851747 




Product 

Type 

Name 

Hercules Single leaf outward opening 

SAF 3 


Double leaf outward opening 


Hercules Single leaf outward opening 

SAF 4 




Structural Opening 

Height (m) 

Structural Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

2.12 1.12 3 953a/01 

2.21 2.21 3 1 953a/02 

2.12 1.12 4 953a/03 

2.21 2.21 4 1 953a/04 

20 Nov 2011 339




LPCB Ref. No. 

Product Name Type Compatible Locking Systems 

953a/01 Hercules SAF 3 Single leaf outw ard opening 


953a/02 Hercules SAF 3 Double leaf outw ard opening 


953a/03 Hercules SAF 4 Single leaf outw ard opening 


953a/04 Hercules SAF 4 Double leaf outw ard opening 



Compatible 

Locking 

System 

Active Leaf 

Passive Leaf 

1 and 2 N/A 

1 and 2 3 

1 and 2 N/A 

1 and 2 3 

Manufacturer Model / Type External Face Internal Face Compatible 

Cylinders 

1 Tindall 

Engineering 

2 Tindall 

Engineering 

3 Commercial 

Body Fittings 

Limited 


Mico 942-3L INT AD / USCH4 

three-point auto-deadlocking 

auto-bolting system w ith 

external cylinder access 

Mico 942-3L INT MD / USCH4 

three-point manual-deadlocking 

auto-bolting system w ith 

external cylinder access 


guard incorporating a 


cylinder 


guard incorporating a 


cylinder 

Thumbturn and lever 

handle 

Thumbturn and lever 

handle 

Sprung tow er bolt - Tw o sprung tow er 

bolts 


Reference 

A Abloy Disclock Pro CY201DP Mechanical Scandinavian oval cylinder 

B Assa 4807 Mechanical Scandinavian oval cylinder 

C Assa C5807 Mechanical Scandinavian oval cylinder 

D Assa Tw in 7607 Mechanical Scandinavian oval cylinder 

E Kaba K20 Oval Mechanical Scandinavian oval cylinder 

F Kaba Quattro S Oval Mechanical Scandinavian oval cylinder 

G Locken CL-PL2WR Mechatronic Scandinavian oval cylinder 2 

Notes: 

1. This rating is achieved with both bolts engaged on the passive leaf engaged and the lock mechanism fitted to the primary leaf 

engaged and deadlocked. The doorset achieves at least Security Rating 1 if one of the bolts on the passive leaf is not engaged. 

2. The resistance of the electronic cylinder to “non-mechanical” attack has not been assessed as it is outside the scope of LPS1175. 

Likewise, the assessment has not covered possible effects of any susceptibilities relating to the functionality and performance of the 

keys that may be used to operate the cylinder. It is therefore recommended that specifiers and installers satisfy themselves that the 

components used are either resistant to mechanical and other forms of tampering/abuse and are resistant to any environmental 

conditions/interference that may cause the lock to disengage. 

A to G 

A to G 

N/A 

R & D Sheetmetal Limited 

Unit 1A, Victoria Court, Colliers Way, Clayton West, Huddersfield, West Yorkshire HD8 9TR, United Kingdom 

Tel: +44 (0)1484 864886 • Fax: +44 (0)1484 866505 

E-mail: sales@randdsheetmetal.co.uk • Website: www.randdsheetmetal.co.uk 


340 20 Nov 2011



Hinged Security Doorset 

Product Product Type 

Name 

Security Single leaf outward 

Evo IV opening hinged security 

Security 

Evo V 

Security 

Evo VI 

doorset 



doorset 



doorset 

Minimum 

Height (m) 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. No. 

1.8 2.3 0.8 1.1 4 1034b/01 

1.8 2.3 0.8 1.1 5 1034b/02 

1.8 2.3 0.8 1.1 6 1034b/03 


Product Name Doorset Configuration 


Security Evo IV Single leaf outw ard opening hinged security doorset 1 to 15 

Security Evo V Single leaf outw ard opening hinged security doorset 16 to 30 

Security Evo VI Single leaf outw ard opening hinged security doorset 31 to 45 


Compatible 

Locking 

System 

Manufacturer Model Type Compatible Operating 

Devices 

External 

Face 

Internal 

Face 

Abryll AD3 Single point locking Key and Thumb turn 

/USCH 4 system w ith automatic lever handle and lever 

Limited 

deadlocking 

handle 

Abryll MD2 

Key and 

/USCH 4 

lever handle 

1 Tindall 

Engineering 

2 Tindall 

Engineering 

Limited 

3 Tindall 

Engineering 

Limited 

4 Tindall 

Engineering 

Limited 

5 Tindall 

Engineering 

Limited 

Abryll MD1 

/USCH 4 

Abryll MD3 

/USCH 4 

Abryll EPC 

MD2 /USCH 4 



deadlocking 



deadlocking 



deadlocking 



deadlocking 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 


A, B, C, D, E, F, G, H, I, J, K, 

L, M, N, O, P, Q, Al, AM, AN, 

AO, AP, AQ and AR 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 

AB, AC, AD, AE, AF, AG, 

AH, AI and AK 

20 Nov 2011 341



6 Tindall 

Engineering 

Limited 

7 Tindall 

Engineering 

Limited 

8 Tindall 

Engineering 

Limited 

9 Tindall 

Engineering 

Limited 

10 Tindall 

Engineering 

Limited 

11 Tindall 

Engineering 

Limited 

12 Tindall 

Engineering 

Limited 

13 Tindall 

Engineering 

Limited 

14 Tindall 

Engineering 

Limited 

15 Tindall 

Engineering 

Limited 

16 Tindall 

Engineering 

Limited 

17 Tindall 

Engineering 

Limited 

18 Tindall 

Engineering 

Limited 

19 Tindall 

Engineering 

Limited 

20 Tindall 

Engineering 

Limited 

Abryll EPC 

MD1 /USCH 4 

Abryll EPC 

MD3 /USCH 4 

Mico EVO 3 

AD3 /USCH 4 

Mico EVO 3 

MD2 /USCH 4 

Mico EVO 3 

MD1 /USCH 4 

Mico EVO 3 

MD3 /USCH 4 

Mico EVO 3 

AD3 EPC 

/USCH 4 

Mico EVO 3 

MD2 EPC 

/USCH 4 

Mico EVO 3 

MD1 

EPC/USCH 4 

Mico EVO 3 

MD3 

EPC/USCH 4 

Abryll AD3 

/USCH 5 

Abryll MD2 

/USCH 5 

Abryll MD1 

/USCH 5 

Abryll MD3 

/USCH 5 

Abryll EPC 

MD2 /USCH 5 



deadlocking 



deadlocking 



deadlocking 


w ith manual deadlocking 







deadlocking 








system w ith automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

342 20 Nov 2011



21 Tindall 

Engineering 

Limited 

22 Tindall 

Engineering 

Limited 

23 Tindall 

Engineering 

Limited 

24 Tindall 

Engineering 

Limited 

25 Tindall 

Engineering 

Limited 

26 Tindall 

Engineering 

Limited 

27 Tindall 

Engineering 

Limited 

28 Tindall 

Engineering 

Limited 

29 Tindall 

Engineering 

Limited 

30 Tindall 

Engineering 

Limited 

31 Tindall 

Engineering 

Limited 

32 Tindall 

Engineering 

Limited 

33 Tindall 

Engineering 

Limited 

34 Tindall 

Engineering 

Limited 

35 Tindall 

Engineering 

Limited 

Abryll EPC 

MD1 /USCH 5 

Abryll EPC 

MD3 /USCH 5 

Mico EVO 3 

AD3 /USCH 5 

Mico EVO 3 

MD2 /USCH 5 

Mico EVO 3 

MD1 /USCH 5 

Mico EVO 

MD3 /USCH 5 

Mico EVO 3 

AD3 EPC 

/USCH 5 

Mico EVO3 

MD2 EPC 

/USCH 5 

Mico EVO 3 

MD1 EPC 

/USCH 5 

Mico EVO 3 

MD3 EPC 

/USCH 5 

Abryll AD3 

/USCH 6 

Abryll MD2 

/USCH 6 

Abryll MD1 

/USCH 6 

Abryll MD3 

/USCH 6 

Abryll EPC 

MD2 /USCH 6 



deadlocking 



deadlocking 



deadlocking 









deadlocking 








system w ith automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

20 Nov 2011 343



36 Tindall 

Engineering 

Limited 

37 Tindall 

Engineering 

Limited 

38 Tindall 

Engineering 

Limited 

39 Tindall 

Engineering 

Limited 

40 Tindall 

Engineering 

Limited 

41 Tindall 

Engineering 

Limited 

42 Tindall 

Engineering 

Limited 

43 Tindall 

Engineering 

Limited 

44 Tindall 

Engineering 

Limited 

45 Tindall 

Engineering 

Limited 

Abryll EPC 

MD1 /USCH 6 

Abryll EPC 

MD3 /USCH 6 

Mico EVO 3 

AD3 /USCH 6 

Mico EVO 3 

MD2 /USCH 6 

Mico EVO 3 

MD1 /USCH 6 

Mico EVO 3 

MD3 /USCH 6 

Mico EVO 3 

AD3 EPC 

/USCH 6 

Mico EVO 3 

MD2 EPC 

/USCH 6 

Mico EVO 3 

MD1 EPC 

/USCH 6 

Mico EVO 3 

MD3 EPC 

/USCH 6 



deadlocking 



deadlocking 



deadlocking 









deadlocking 







Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key and 

lever handle 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and lever 

handle 

Key or 

thumb turn 

and push 

plate 

Key or 

thumb turn 

and push 

pad 

Key or 

thumb turn 

and lever 

handle 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



A, B, C, D, E, F, G, H, I, J, K, 



R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 

R, S, T, U, V, W, X, Y, Z, AA, 


AH, AI and AK 



Reference 

A Abloy Protec CY201 PT Scandinavian Oval 

B Abloy Protec Cliq CY201 Scandinavian Oval 

C AMS CL-OVLD Scandinavian Oval 

D ASSA 4401dp Scandinavian Oval 

E ASSA 4401 Cliq Scandinavian Oval 

F ASSA 4407dp Scandinavian Oval 

G ASSA 4407 Cliq Scandinavian Oval 

H ASSA 4801 Scandinavian Oval 

I ASSA 4807 Scandinavian Oval 

344 20 Nov 2011



J ASSA C5801 Scandinavian Oval 

K ASSA C5807 Scandinavian Oval 

L ASSA Tw in 7601 Scandinavian Oval 

M ASSA Tw in 7607 Scandinavian Oval 

N Kaba K20 Scandinavian Oval 

O Kaba Quattro PluS Scandinavian Oval 

P Locken CL-PL2WR Scandinavian Oval 

Q Medeco M3-ARX Scandinavian Oval 

R Abloy Protec CY304 Europrofile double cylinder (key:key) 

S Abloy Protec Cliq CY333 Europrofile double cylinder (key:thumbturn) 

T Abloy Protec CY333 Europrofile double cylinder (key:thumbturn) 

U Abloy Protec Cliq CY304 Europrofile double cylinder (key:key) 

V Abloy Protec CY305 Europrofile double cylinder (key:thumbturn) 

W Abloy Protec Cliq CY305 Europrofile double cylinder (key:thumbturn) 

X ASSA 4422dp Europrofile double cylinder (key:key) 

Y ASSA 4427dp Europrofile double cylinder (key:thumbturn) 

Z ASSA 44M22 Cliq Europrofile double cylinder (key:key) 

AA ASSA 44M27 Cliq Europrofile double cylinder (key:thumbturn) 

AB ASSA 4822 Europrofile double cylinder (key:key) 

AC ASSA 4827 Europrofile double cylinder (key:thumbturn) 

AD ASSA C5822 Europrofile double cylinder (key:key) 

AE ASSA C5827 Europrofile double cylinder (key:thumbturn) 

AF ASSA 7622 Europrofile double cylinder (key:key) 

AG ASSA 7627 Europrofile double cylinder (key:thumbturn) 

AH Kaba Quattro PluS Europrofile double cylinder (key:key) 

AI Kaba Quattro PluS Europrofile double cylinder (key:thumbturn) 

AJ Medeco M3-ARX Europrofile double cylinder (key:key) 

AK Medeco M3-ARX Europrofile double cylinder (key:thumbturn) 

AL Abloy Protec CY403 Rim 

AM Abloy Protec Cliq CY403 Rim 

AN Kaba Quatro Plus Rim 

AO Medeco M3-ARX Rim 

AP AMS CL-CA2D Finish Round 

AQ ASSA 4857 Round threaded 

AR ASSA C5857 Round threaded 

Notes: 

1. Certification does not cover the use of locks other than those listed above. Utilisation of unlisted locks may affect the level of security 

offered by the doorset. 

2. The doorset’s resistance relies on the supporting substrate offering compatible resistance to manual attack. 

3. The Security Evo IV doorset is approved when installed in accordance with the instructions detailed on document EVO-INST-02 

(Issue 1). 

4. The Security Evo V and VI doorsets are approved when installed in accordance with the instructions detailed on document EVO- 

INST-01 (Issue 3) into the Security Evo enclosures only. 

20 Nov 2011 345





Tel: +44 (0)1929 551100 • Fax: +44 (0)1929 553300 





Clear 

Opening 

Height 

(m) 

Safe Doorset SR1 Single leaf 

outward 

opening 


timber doorset 

Safe Doorset SR2 Single leaf 

outward 

opening 


timber doorset 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

1.8 2 0.675 0.825 2 835a/01 

1.8 2 0.675 0.825 2 1 835a/02 


Lock 

Position 

Upper 

Middle 

Low er 

Lockset Cylinder Associated 

Ironmongery 

ERA mortice deadlock 

(Product code 325-31) 

ERA Euro Pro Fit 

sashlock (Product code 

326-31) 

ERA Fortress 5 lever 

mortice sashlock 


ERA mortice deadlock 


ERA Satin 35/35 mm 

key/thumbturn europrofile 

double cylinder (Product 

code 4103-51) 




code 4103-51) 




code 4103-51) 

- 

Solon Satin Escutcheons 

(Product code 263 55 

ESC) 

Solon Satin sash lever 

handle fitted to each face 

(Product code BD0406) 

Solon Satin sash lever 

handle fitted to each face 


Solon Satin Escutcheons 

(Product code 263 55 

ESC) 

Doorset 

SR1 SR2 

 

 

 

 

Note: 

1. This doorset achieves it’s Security Rating when all three locks are engaged. The doorset achieves Security Rating 1 when only one 

lock is engaged. 

SafeGuard Doors, A Division of Adams Rite Europe Limited 

School Street, Willenhall, West Midlands WV13 3PW, United Kingdom 

Tel: +44 (0))1902 364601 • Fax: +44 (0)1902 364602 

E-mail: sales@safeguarddoors.co.uk • Website: www.safeguarddoors.co.uk 


346 20 Nov 2011




Product 

Type 

Name 

Trenchard 

Fenwick 





Minimum 

Clear 

Opening 

Height (m) 

Maximum 

Clear 

Opening 

Height (m) 

Minimum 

Clear 

Opening 

Width (m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

1.8 2.4 0.76 1.2 3 661a/01 

1.8 2.4 0.76 1.2 4 661a/02 


LPCB 

Ref. No. 

Trade 

Name 

Com patible Locking Systems 

Manufacturer Model Type Compatible Cylinders 

661a/01 Trenchard Surelock McGill EX210(B1) -L1 Three point surface 

mounted locking system 

fitted w ith push bar and 

LEO external operating 

device 

661a/02 Fenw ick Surelock McGill EX210(B1) Three point surface 

mounted locking system 

fitted w ith push bar 

Bramah C17SI 

DOM 419ix10G 

Kaba KV207.0000C5-SC 

Union 26X11B 

Yale PK1133 Pro-Key 

N/A 

Stafford Bridge Doors Limited 

Bedford Road, Pavenham, Bedford MK43 7PS, United Kingdom 

Tel: +44 (0)1234 826316 • Fax: +44 (0)1234 826319 

E-mail: sales@sbdoors.com • Website: www.surelockmcgillgroup.com/sbd 



Product 

Type 

Name 

Sandhurst 

Wilton 

Halton 

Sandhurst 

Wilton 

Halton 

Single leaf, outward and 

inward opening hinged 


Single leaf, outward 


doorset 

Single leaf, outward 


doorset 



doorset 



doorset 



doorset 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

1.9 2.5 0.7 1.4 3 516a/01 

1.9 2.5 0.7 1.4 4 516a/03 

1.468 2.5 0.7 1.4 4 516a/04 

1.9 2.5 1.4 3.0 3 516a/05 

1.9 2.5 1.4 3.0 4 516a/06 

1.9 2.5 1.4 3.0 4 516a/07 


20 Nov 2011 347



LPCB Ref. 

No. 

Trade 

Name 

516a/01 Sandhurst 

Type 



Nom inal 


Leaf 

Thickness 

Active Leaf 

Passive Leaf 

(mm) 

46 AA, AB, AC, AD1, AE, AF1, AG, N/A 

AH, AI, AJ, AK1, AL, AM1, AN1, 

AN3, AO, AP, AQ1, AR1 and AU 

Single leaf inw ard 


516a/03 Wilton Single leaf outw ard 


516a/04 Halton Single leaf outw ard 


516a/05 Sandhurst Double leaf outw ard 


516a/06 Wilton Double leaf outw ard 


516a/07 Halton Double leaf outw ard 


54 AA, AB, AC, AD, AD1, AE, AF, 

AF1, AG, AH, AI, AJ, AK, AL, 

AM, AN1, AN2, AO, AP, AQ, AR 

and AU 

46 AA, AB, AC, AD1, AE, AF1, AI, 

AJ, AK1, AL, AM1, AO, AP, AQ1 

and AR1 

54 AA, AB, AC, AD, AD1, AE, AF, 

AF1, AI, AJ, AK, AL, AM, AO, 

AP, AQ and AR 

55 AC1, AJ1, AK2, AL, AM2, AN, 

AP1, AQ2, AR2 and AS 

55 AC1, AJ1, AK2, AL, AM2, AN, 

AP1, AQ2, AR2 and AS 

46 AD1, AE, AF1, AK1, AL, AM1, 

AN1, AN3, AQ1 and AR1 

54 AD, AE, AF, AK, AL, AM, AN1, 

AN2, AQ and AR 

55 AK2, AL , AM2, AN, AQ2, AR2 

and AS 

55 AK2, AL , AM2, AN, AQ2, AR2 

and AS 

N/A 

N/A 

N/A 

N/A 

N/A 

AT or tw o-point bolting version 

of locking system on the active 

leaf 



leaf 



leaf 



leaf 


348 20 Nov 2011



Compatible Manufacturer Model Type Compatible Cylinders 

Locking 

System 

AA Surelock McGill Trimlock (D117) Three point mortice locking system 4, 5 1 , 7, 8 1 , 14, 15 1 , 19, 20 1 , 24, 25 1 , 

27, 28 1 , 35, 36 1 , 39, 40 1 , 43, 44 1 , 49, 

50 1, 54 and 55 1 

AB Surelock McGill EX110-L1 Three point surface mounted 22, 29, 33, 46, 51 and 52 

emergency exit system fitted w ith 

lever handle or push pad and LEO 

module 

AC Surelock McGill EX210-L1 Three point surface mounted panic 22, 29, 33, 46, 51 and 52 

exit system fitted w ith push bar and 

LEO module 

AC1 Surelock McGill EX210-L2 Three point surface mounted panic 


'SR4' LEO module 

22, 29, 33, 46, 51 and 52 

AD Surelock McGill DL200-P Three point surface mounted locking 

system w ith automatic cylinder 

deadlock operated by key (outside) 

and turn-knob (inside) 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

AD1 Surelock McGill DL200-K15P Three point surface mounted locking 


2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 


and turn-knob (inside) w ith integrated 

turn-knob protection shroud 

AD2 Surelock McGill DL200-K15P5 Three point surface mounted locking 





2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

AE Surelock McGill DL100 Three point surface mounted locking 

system w ith lever-key operated 

deadlock 

AF Surelock McGill DL106-P Three point surface mounted locking 

system w ith cylinder deadlock 

operated by key (outside) and turnknob 

(inside) 

AF1 Surelock McGill DL106-K15P Three point surface mounted locking 



(inside) w ith integrated turnknob 

protection shroud 

N/A 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

20 Nov 2011 349



AF2 Surelock McGill DL106-K15P5 Three point surface mounted locking 





AG Surelock McGill Stirling DL800 Single point surface mounted locking 

w ith K2 and K13P device w ith cylinder deadlock 

options 


(inside) 

AH Surelock McGill Stirling EX800 Single point surface mounted 

w ith K2 and K13P emergency exit device fitted w ith 

options 

external key access 

AI Surelock McGill A1-L1 Three point surface mounted locking 

system fitted w ith lever handle or 

push pad and LEO module 

AJ Surelock McGill B1-L1 Three point surface mounted panic 


LEO module 

AJ1 Surelock McGill B1-L2 Three point surface mounted panic 


'SR4' LEO module 

AK Surelock McGill C1-P Three point surface mounted locking 




2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 3, 6, 10, 12, 13, 17, 18, 21, 23, 26, 

30, 31, 34, 38, 41, 42, 45, 47, 48, 53, 

56, 57 and 58 

2, 3, 6, 10, 12, 13, 17, 18, 21, 23, 26, 

30, 31, 34, 38, 41, 42, 45, 47, 48, 53, 

56, 57 and 58 

22, 29, 33, 46, 51 and 52 

22, 29, 33, 46, 51 and 52 

1, 9, 11, 16, 22, 29, 32, 37, 46, 51 

and 52 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

AK1 Surelock McGill C1-K15P Three point surface mounted locking 





2, 10, 12, 17, 21, 30, 31, 41, 42, 48 , 

56, 57 and 58 

AK2 Surelock McGill C1-K15P5 Three point surface mounted locking 


2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 




AL Surelock McGill D1 Three point surface mounted locking 

system w ith lever-key operated 

deadlock 

N/A 

350 20 Nov 2011

AM Surelock McGill D6-P Three point surface mounted locking 



(inside) 

AM1 Surelock McGill D6-K15P Three point surface mounted locking 





AM2 Surelock McGill D6-K15P5 Three point surface mounted locking 





AN Surelock McGill 25C1-P5R# 2,3 X 25mm throw three point locking 

system w ith solenoid 2 deadlock 

(pow er to release) and external 

cylinder operation 

AN1 Surelock McGill 25C1-PR# 2,3 X 25mm throw three point locking 




AN2 Surelock McGill 25C1-PR# 2,3 25mm throw three point locking 




AN3 Surelock McGill 25C1-K15 PR# 2,3 25mm throw three point locking 


(pow er to release) external cylinder 

operation 

AO Surelock McGill Slimline 315R-L1 

or 315L-L1 

AP Surelock McGill Slimline 314R-L1 

or 314L-L1 

AP1 Surelock McGill Slimline 314R-L2 

or 314L-L2 



2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

Three point surface mounted 22, 29, 33, 46, 51 and 52 

emergency exit system fitted w ith 

lever handle or push pad and LEO 

module 5 

Three point surface mounted panic 22, 29, 33, 46, 51 and 52 


LEO module 6 

Three point surface mounted panic 1, 9, 11, 16, 22, 29, 32, 37, 46, 51 

exit system fitted w ith push bar and and 52 

'SR4' LEO module 6 

AQ Surelock McGill Slimline 313-KP Three point surface mounted locking 




2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

20 Nov 2011 351



AQ1 Surelock McGill Slimline 313- 

KK15P 

AQ2 Surelock McGill Slimline 313- 

KK15P5 

AR Surelock McGill Slimline 313-A0P Three point surface mounted locking 


operated by key (outside)and turnknob 

(inside) 

AR1 Surelock McGill Slimline 313- 

A0K15P 

AR2 Surelock McGill Slimline 313- 

A0K15P5 

AS Surelock McGill Slimline 325R- 

K2P5 R# 2,3 or 

325L-K2P5 R# 2,3 

Three point surface mounted locking 2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

system w ith automatic cylinder 56, 57 and 58 




Three point surface mounted locking 2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

system w ith automatic cylinder 56, 57 and 58 




Three point surface mounted locking 





Three point surface mounted locking 





25mm throw three point locking 




AT Surelock McGill S3TB-W Barrel bolt (2 off) N/A 

AU Surelock McGill Stirling AC800 2 


w ith K2 and K13P 

options 

Single point surface mounted 

solenoid 2 (pow er to release) fitted 

w ith external key access 

Compatible Manufacturer Model Type 

Cylinder 

1 Abloy Disklock Pro CY404 DP Screw -in single cylinder 

2 Abloy Disklock Pro CY405 DP Rim cylinder 

3 Abloy Disklock Pro CY303 DP Single Europrofile cylinder 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 10, 12, 17, 21, 30, 31, 41, 42, 48, 

56, 57 and 58 

2, 3, 6, 10, 12, 13, 17, 18, 21, 23, 26, 

30, 31, 34, 38, 41, 42, 45, 47, 48, 53, 

56, 57 and 58 

4 Abloy Disklock Pro CY304 DP Double Europrofile cylinder (key:key) 

5 Abloy Disklock Pro CY305 DP Double Europrofile cylinder (key:thumbturn) 1 

6 Assa 4823 Single Europrofile cylinder 

7 Assa 4822 Double Europrofile cylinder (key:key) 

8 Assa 4824 Double Europrofile cylinder (key:thumbturn) 1 

9 Assa 4851 Screw -in single cylinder 

10 Assa 4857 Rim cylinder 

352 20 Nov 2011



11 Assa C5851 Screw -in single cylinder 

12 Assa C5857 Rim cylinder 

13 Assa Ruko Flexcore - F523 Single Europrofile cylinder 

14 Assa Ruko Flexcore - F522 Double Europrofile cylinder (key:key) 

15 Assa Ruko Flexcore - F524 Double Europrofile cylinder (key:thumbturn) 1 

16 Assa F551 Screw -in single cylinder 

17 Assa Ruko Flexcore - F557 Rim cylinder 

18 Assa Tw in Combi - C5823 Single Europrofile cylinder 

19 Assa Tw in Combi - C5822 Double Europrofile cylinder (key:key) 

20 Assa Tw in Combi - C5821 Double Europrofile cylinder (key:thumbturn) 1 

21 Bramah C17 Rim cylinder 

22 Bramah C17SI Screw -in single cylinder 

23 Chubb TXE3010 Single Europrofile cylinder 

24 Chubb TXED3030 Double Europrofile cylinder (key:key) 

25 Chubb TXET3030 Double Europrofile cylinder (key:thumbturn) 1 

26 Dom 333 H RS5 Single Europrofile cylinder 

27 Dom 333 RS5 Double Europrofile cylinder (key:key) 

28 Dom 333 K RS5 Double Europrofile cylinder (key:thumbturn) 1 

29 Dom 419ix10KG Screw -in single cylinder 

30 Dom 555ix10G Rim cylinder 

31 Kaba KV06.100 Rim cylinder 

32 Kaba K207.203 C5-SC Screw -in single cylinder 

33 Kaba K2070000C5-SC Armoured screw -in single cylinder 

34 Kaba QS 152.100.00 Single Europrofile cylinder 

35 Kaba QS 150.100.00 Double Europrofile cylinder (key:key) 

36 Kaba QS 151.100.00 Double Europrofile cylinder (key:thumbturn) 1 

37 Medeco BX664 Screw -in single cylinder 

38 Medeco BX665 Single Europrofile cylinder 

39 Medeco BX666 Double Europrofile cylinder (key:key) 

40 Medeco BX667 Double Europrofile cylinder (key:thumbturn) 1 

41 Medeco BX668 Rim cylinder 

42 Union 1x1 Rim cylinder 

43 Union 2x18AA Double Europrofile cylinder (key:key) 

44 Union 2x19AA Double Europrofile cylinder (key:thumbturn) 1 

45 Union 2x20A Single Europrofile cylinder 

46 Union 26x11B Screw -in single cylinder 

47 Yale 10026 Single Europrofile cylinder 

48 Yale 1109.SCP Rim cylinder 

49 Yale 22626 Double Europrofile cylinder (key:key) 

50 Yale 32626 Double Europrofile cylinder key:thumbturn) 1 

20 Nov 2011 353



51 Yale PK1133 Pro-key Screw -in single cylinder 

52 Medeco M3ARX MOTC-1001 Screw -in single cylinder 

53 Medeco M3ARX ESS-000-047 Single Europrofile cylinder 

54 Medeco M3ARX ETS-032-032 Double Europrofile cylinder (key:key) 

55 Medeco M3ARX ETT-032-032 Double Europrofile cylinder (key:thumbturn) 1 

56 Medeco M3ARX RIMC-10516 Rim cylinder 

57 AMS CL-OVLD Scandinavian Oval mechatronic cylinder 7 

58 AMS CL-CA2D Finish Round mechatronic cylinder 7 

Accessories 

Accessory Description Compatible Doorsets (LPCB Cert. No. 516a/..) 

01 4 03 04 05 4 06 07 

Vision panels 150 mm w ide by 350 mm high vision panels 8 

 

 

incorporating Tego S28 glazing units. 

Side panels 9 Single timber side panels to either side of the doorset. 

Over-panels 9 Single timber overhead panel. 

Surface-mounted 

cable conduits 

Concealed cable 

conduits 

Cable conduits mounted on the non-attack face of the 

leaf, through w hich cables are routed to energise 

solenoid-operated locking systems. 

Cable conduits concealed w ithin the thickness of the 

leaf, through w hich cables are routed to energise 

solenoid-operated locking systems. 

Supply voltage of solenoid-operated locking systems 

 

 

 

Compatible Doorsets 

(LPCB Cert. No. 516a/..) 

01 and 05 

Configuration 

Surface-mounted cable Concealed cable 

conduits 

conduits 

Plain doorset 12 V, 24 V and 50 V 12 V, 24 V and 50 V 

Doorset w ith vision panels 12 V, 24 V and 50 V 12 V, 24 V and 50 V 

Doorset w ith side panels 50 V 50 V 

03, 04, 06 and 07 

Doorset w ith overhead panels 12 V, 24 V and 50 V 10 12 V, 24 V and 50 V 10 

Plain doorset 12 V, 24 V and 50 V - 

Doorset w ith side panels 50 V - 

Doorset w ith overhead panels 12 V, 24 V and 50 V 10 - 

Notes: 

1. The ‘thumbturn’ end of the lock cylinder should be located on the non-attack side of the doorset when the doorset is installed. These 

cylinders are unsuitable for use with the Trimlock when fitted to the ‘46 mm thick’ version of the Sandhurst doorset. 

2. The resistance of these access control locks to ‘non-mechanical’ attack has not been assessed as it is outside the scope of LPS1175. 

Likewise, the assessment has not covered possible effects of any susceptibilities relating to the functionality and performance of any 


and system configurations that may be used with these locking systems is ‘infinite’. It is therefore recommended that specifiers and 

installers satisfy themselves that the components used are either resistant to mechanical and other forms of tampering/abuse, or that 

they are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may cause 

the locking system to disengage. 

3. This approval covers the use of Surelock McGill’s lock option codes R (12 V), R1 (24 V) and R4 (50 V). These reflect the supply 

voltage required and that the locks are configured in the ‘power to release’ mode. The actual voltages that are compatible on each 

doorset are identified in the table above entitled ‘Supply voltage of solenoid-operated locking systems’. 

4. The vision panels are only approved on the Sandhurst doorsets when used in conjunction with lock options AA, AE, AF1, AD1, AG, 

AU, AQ and AR. 

5. The approval covers the use of either the H3 or H21 versions of the push pad. 

6. The approval covers the use of either the standard or H20 versions of the panic bar. 

7. The resistance of the mechatronic cylinders to ‘non-mechanical’ attack has not been assessed as it is outside the scope of LPS 1175. 

Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and performance of ancillary 

equipment that may be used in conjunction with those cylinders. It is therefore recommended that specifiers satisfy themselves that 

the components used are either resistant to electronic methods of attack, or that they are suitably protected from such 

tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking system to disengage. 

8. Two locations are approved. These are both 375 mm from the leading edge of the leaf and either 625 mm or 1325 mm from the 

bottom of the leaf. 

354 20 Nov 2011



9. The side and overhead panels are available in fixed and removable variants of the configurations and overall dimensions defined on 

documents D12167.01 (Issue A) through to D12167.30 (Issue A). The approval only covers the provision of a single panel to each 

side of the doorset, and a single panel above the doorset. The provision of multiple panels in any direction is outside the scope of this 

approval. 

10. Doorsets with overhead panels and cable conduits are compatible with 12 V, 24 V and 50 V solenoid-operated locking systems on 

the basis that cables are not routed via the overhead panels. 



Product Product Type 

Name 

Hendon 

Single leaf 

inward 

opening 

doorset 

Single leaf 

outward 

opening 

doorset 

Double leaf 1 

inward 

opening 

doorset 

Double leaf 1 

outward 

opening 

doorset 

Minimum 

Structural 


(m) 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.9 2.5 0.7 1.4 2 516c/01 

1.9 2.5 0.7 1.4 2 

1.9 2.5 1.4 3.0 2 2 

1.9 2.5 1.4 3.0 2 2 


LPCB 

Ref. No. 

Trade 

Name 

Type 

516c/01 Hendon Single leaf inw ard 


Single leaf 


doorset 

Double leaf 

inw ard opening 

doorset 

Double leaf 


doorset 

Nomimal Leaf 

Thickness 

(mm) 

Com patible Locking Systems 

Active Leaf 

46 1, 2, 5, 6, 9, 10, 11, 12, 16, 17, 19, 20, 

22, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 

35, 36, 37, 38, 39, 40, 41, 42 and 43 

54 1, 2, 3, 5, 6, 7, 8, 9, 10, 11, 12, 16, 17, 

18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 

29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 

40, 41, 42 and 44 

46 2, 5, 6, 9, 10, 11, 12, 16, 17, 19, 20, 22, 

25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 

36, 37, 38, 39, 40, 41, 42 and 43 

54 2, 3, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 16, 

17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 

28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 

39, 40, 41, 42 and 44 

46 5, 6, 9, 10, 11, 12, 16, 17, 19, 20, 22, 25 

and 26 

27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 

38, 39, 40, 41 and 42 

54 3, 5, 6, 7, 8, 9, 10, 11, 12, 16, 17, 18, 19, 

20, 21, 22, 23, 24, 25 and 26 

27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 

38, 39, 40, 41 and 42 

46 5, 6, 9, 10, 11, 12, 16, 17, 19, 20, 22, 25 

and 26 

54 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 15, 16, 17, 

18, 19, 20, 21, 22, 23, 24, 25 and 26 

Passive Leaf 

N/A 

N/A 

N/A 

N/A 

45 or tw o-point version of 

the active leaf lock 

45 



45 






20 Nov 2011 355



Locking 

System 

Manufacturer Model Type Operating Devices Com patible 


Cylinders 

1 Dom Nemef Nemef 

642/17 

2 Dom Nemef Nemef 

6602/32 

Single-point mortice deadlock 

w ith internal quick release 

handle 

Single-point mortice deadlock 

3 Surelock McGill SL301-0X- 

O0W 

Slimline three-point surfacemounted 


4 Surelock McGill SL304-0X- Slimline three-point surfacemounted 

W 


5 Surelock McGill SL305- Slimline three-point surfacemounted 

H3Q4 


6 Surelock McGill SL305-Q4 Slimline three-point surfacemounted 


7 Surelock McGill SL311-0X- Slimline three-point surfacemounted 

A0K0O0PW 

locking system w ith 

manual bolting and deadlocking 


K0O0PW 

9 Surelock McGill SL313- 

A0K15P 






manual bolting 

10 Surelock McGill SL313-A0P Slimline three-point surfacemounted 


manual bolting 

16 Surelock McGill SL315- Slimline three-point surfacemounted 

H3PW 


17 Surelock McGill SL315-PW Slimline three-point surfacemounted 



K2O0R#PW 


locking system w ith fail 

secure solenoid 6,7 

19 Surelock McGill SL322-PR# Slimline three-point surfacemounted 




K15PR# 




21 Surelock McGill SL323-P Slimline three-point surfacemounted 






H3K2O0R#P 

W 


K2O0R#PW 


H3PR# 










Key 3 and lever 

handle 


handle 

None 

Lever handle 

Key or 

thumbturn and 

lever handle 

Key and lever 

handle 

L to T 

U to AL 

N/A 

None Panic bar 4 N/A 

None Push pad 5 N/A 

None Lever handle N/A 


handle 


handle 


handle 


handle 


handle 


handle 

Electric release 

w ith key 3 

override and 

lever handle 


and lever 

handle 


and lever 

handle 


and lever 

handle 


and lever 

handle 


w ith key 3 

override and 

lever handle 


w ith key 3 

override and 

lever handle 


and lever 

handle 

Key and lever 

handle 

Key and lever 

handle 

Shrouded 

thumbturn and 

lever handle 

Thumbturn and 

lever handle 

Push pad 5 

Lever handle 


and lever 

handle 


and lever 

handle 

Shrouded 

thumbturn and 

lever handle 

Thumbturn and 

lever handle 

Thumbturn and 

lever handle 

Push pad 5 

Lever handle 

Push pad 5 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

356 20 Nov 2011




27 Surelock McGill ST105- 

H3Q4 

Stirling single-point surfacemounted 


28 Surelock McGill ST105-Q4 Stirling single-point surfacemounted 


29 Surelock McGill ST113- Stirling single-point surfacemounted 

K13P 


30 Surelock McGill ST113-K2 Stirling single-point surfacemounted 



H3K13P 



H3K2 



K13P 


34 Surelock McGill ST115-K2 Stirling single-point surfacemounted 



K13PR# 


K2R# 


K13PR# 


K2R# 


H3K13PR# 


H3K2R# 


K13PR# 


K2R# 

43 Surelock McGill Trimlock 

DL117 

44 Surelock McGill Trimlock 

DL137 



























Three-point mortice locking 

system 

Three-point mortice locking 

system 


w ith key 3 

override and 

lever handle 

Lever handle A to K 

None Push pad 5 N/A 

None Lever handle N/A 

Key 3 and lever Thumbturn and 


Key 3 and lever Thumbturn and 


Key 3 and lever Push pad 5 

handle 

Key 3 and lever Push pad 5 

handle 

Key 3 and lever Lever handle 

handle 

Key 3 and lever Lever handle 

handle 

Electric release Electric release 

and lever and lever 

handle handle 

Electric release Electric release 

w ith key 3 and lever 

override and handle 

lever handle 

Electric release Thumbturn and 

and lever lever handle 

handle 

Electric release Thumbturn and 

w ith key 3 lever handle 

override and 

lever handle 

Electric release Push pad 5 

and lever 

handle 

Electric release Push pad 5 

w ith key 3 

override and 

lever handle 

Electric release Lever handle 

and lever 

handle 

Electric release Lever handle 

w ith key 3 

override and 

lever handle 

Key 3 and lever Key or 

handle thumbturn and 

lever handle 

Key 3 and lever Key or 

handle thumbturn and 

A to T 

A to T 

A to T 

A to T 

A to T 

A to T 

A to T 

A to T 

A to K 

A to K 

A to K 

A to K 

A to K 

A to K 

U to AL 

U to AL 

lever handle 

45 Surelock McGill S3TB-W Tow er bolts (2 off) None Tow er bolt N/A 


20 Nov 2011 357




A Abloy Disklock Pro CY405 DP Rim cylinder 

B Assa 4857 Rim cylinder 

C Assa Tw in Combi - C5857 Rim cylinder 

D Assa Ruko Flexcore - F557 Rim cylinder 

E Bramah C17 Rim cylinder 

F Dom 555ix10G Rim cylinder 

G Kaba KV06.100 Rim cylinder 

H Medeco BX668 Rim cylinder 

I Medeco M3ARX RIMC-10516 Rim cylinder 

J AMS CL-OVLD Scandinavian Oval mechatronic 8 cylinder 

K AMS CL-CA2D Finish Round mechatronic 8 cylinder 

L Abloy Disklock Pro CY303 DP Single europrofile cylinder 

M Assa 4823 Single europrofile cylinder 

N Assa Ruko Flexcore - F523 Single europrofile cylinder 

O Assa Tw in Combi - C5823 Single europrofile cylinder 

P Chubb TXE3010 Single europrofile cylinder 

Q Dom 333 H RS5 Single europrofile cylinder 

R Kaba QS 152.100.00 Single europrofile cylinder 

S Medeco BX665 Single europrofile cylinder 

T Medeco M3ARX ESS-000-047 Single europrofile cylinder 

U Abloy Disklock Pro CY304 DP Double europrofile cylinder (key:key) 

V Abloy Disklock Pro CY305 DP Double europrofile cylinder (key:thumbturn) 9 

W Assa 4822 Double europrofile cylinder (key:key) 

X Assa 4824 Double europrofile cylinder (key:thumbturn) 9 

Y Assa Ruko Flexcore - F522 Double europrofile cylinder (key:key) 

Z Assa Ruko Flexcore - F524 Double europrofile cylinder (key:thumbturn) 9 

AA Assa Tw in Combi - C5822 Double europrofile cylinder (key:key) 

AB Assa Tw in Combi - C5821 Double europrofile cylinder (key:thumbturn) 9 

AC Chubb TXED3030 Double europrofile cylinder (key:key) 

AD Chubb TXET3030 Double europrofile cylinder (key:thumbturn) 9 

AE Dom 333 RS5 Double europrofile cylinder (key:key) 

AF Dom 333 K RS5 Double europrofile cylinder (key:thumbturn) 9 

AG Kaba QS 150.100.00 Double europrofile cylinder (key:key) 

AH Kaba QS 151.100.00 Double europrofile cylinder (key:thumbturn) 9 

AI Medeco BX666 Double europrofile cylinder (key:key) 

AJ Medeco BX667 Double europrofile cylinder (key:thumbturn) 9 

AK Medeco M3ARX ETS-032-032 Double europrofile cylinder (key:key) 

AL Medeco M3ARX ETT-032-032 Double europrofile cylinder (key:thumbturn) 9 

Accessories 

358 20 Nov 2011



Accessory Description Compatible Doorsets 

(LPCB Ref. No. 516c/01) 

Vision panels 150 mm w ide by 350 mm high vision panels 10 incorporating ‘Tecdur DC28’ glazing 

11 

units. 

150 mm w ide by 350 mm high vision panels 10 incorporating ‘Tecdur DC46’ glazing 

12 

units. 

Side panels 13 Single timber side panel to either side of the doorset. 

Overhead Single timber overhead panel. 

panels 13 

Surface-mounted 

cable conduits 

Cable conduits mounted on the non-attack face of the leaf, through w hich cables 

are routed to energise solenoid-operated locking systems. 

 

Concealed cable 

conduits 

Cable conduits concealed w ithin the thickness of the leaf, through w hich cables 

are routed to energise solenoid-operated locking systems. 

 

Supply Voltage of Solenoid-Operated Locking Systems 

Configuration 

Doorset w ith cable conduits 

Doorset w ith side panels and cable conduits 

Doorset w ith overhead panels and cable conduits 

Doorset w ith vision panels and cable conduits 

Com patible Doorsets 

(LPCB Ref. No. 516c/01 14 ) 

12 V, 24 V and 50 V 

12 V, 24 V and 50 V 

12 V, 24 V and 50 V 

12 V, 24 V and 50 V 

Notes: 

1. The approval only covers double leaf doorsets with leafs of equal width. 

2. The doorset achieves a Security Rating 2 classification when placed in the optimum locked condition. A Security Rating 1 

classification prevails when placed in the minimum locked condition. That condition exists when either: 

a. One tower bolt is engaged, the active leaf locking system is engaged and the external key is removed. 

b. The two-point manual bolting version of the locking system fitted to the active leaf was disengaged, the active leaf locking system 

is engaged and the external key is removed. 

3. The external cylinder is protected within a Surelock McGill ‘P’ cylinder guard. 

4. The approval covers the use of either the standard or H20 versions of the panic bar. 

5. The approval covers the use of either the H3 or H21 versions of the push pad. 

6. This approval covers the use of Surelock McGill’s lock option codes R (12 V), R1 (24 V) and R4 (50 V). These reflect the supply 

voltage required and that the locks are configured in the ‘power to release’ mode. The actual voltages that are compatible on each 

doorset are identified in the table above entitled ‘Supply voltage of solenoid-operated locking systems’. 

7. The resistance of these access control locks to ‘non-mechanical’ attack has not been assessed as it is outside the scope of LPS1175. 



and system configurations that may be used with these locking systems is ‘infinite’. It is therefore recommended that specifiers and 

installers satisfy themselves that the components used are either resistant to mechanical and other forms of tampering/abuse, or that 

they are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may cause 

the locking system to disengage. 

8. The resistance of the mechatronic cylinders to ‘non-mechanical’ attack has not been assessed as it is outside the scope of LPS 1175. 

Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and performance of ancillary 

equipment that may be used in conjunction with those cylinders. It is therefore recommended that specifiers satisfy themselves that 

the components used are either resistant to electronic methods of attack, or that they are suitably protected from such 

tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking system to disengage. 

9. The ‘thumbturn’ end of the lock cylinder should be located on the non-attack side of the doorset when the doorset is installed. 

10. Two locations are approved. These are both 375 mm from the leading edge of the leaf and either 625 mm or 1325 mm from the 

bottom of the leaf. 

11. ‘Tecdur DC28’ glazing units should not be used in combination with locking systems 4, 13, 14 or 15. 

12. ‘Tecdur DC46’ glazing units should not be used in combination with locking systems 1 to 3, 5 to 12 or 16 to 44. 

13. The side and overhead panels are available in fixed and removable variants of the configurations and overall dimensions defined on 

documents D12167.01 (Issue A) through to D12167.30 (Issue A). The approval only covers the provision of a single panel to each 

side of the doorset, and a single panel above the doorset. The provision of multiple panels in any direction is outside the scope of this 

approval. 

14. ‘Hendon’ doorsets may incorporate surface-mounted or concealed cable conduits, as illustrated on documents D12183.06 (Issue A) 

and D12183.07 (Issue A). 

20 Nov 2011 359





Tel: +44 (0)1233 639039 • Fax: +44 (0)1233 625137 




Product 

Type 

Name 

ExcluDoor 3 

ExcluDoor 4 

ExcluDoor 3 

ExcluDoor 4 

ExcluDoor 4 

F.R. 

ExlcuDoor 4 

F.R. 

Minimum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening: 

Width 

(m) 

Maximum 

Clear 

Opening: 

Width 

(m) 

Security 

Rating 



1.8 2.4 1.4 2.4 3 234c/01 

Double leaf, outward opening 1.8 2.4 1.24 2.4 4 234c/02 


Single leaf, outward opening 1.8 2.4 0.75 1.24 4 234c/03 

hinged security doorset with multipoint 

locking systems 


- 2.25 - 1.1 3 234c/04 


Single leaf, outward opening 1.8 2.25 0.75 1.24 4 234c/05 

hinged security doorset with two 

single point locks 


hinged security doorset with a 

single point lock 

Double leaf, outward opening 1.8 2.4 1.24 2.4 4 234c/07 

multi point locking systems 10 

hinged security doorset with 


hinged security doorset with 

multi point locking systems 

Cert. 

No. 


LPCB Ref. No. Trade Name Compatible Locking Devices 

Active Leaf 

Passive Leaf 

234c/01 ExcluDoor 3 11, 12 or 32 9 

234c/02 ExcluDoor 4 1, 2, 3 1 , 4 1 , 5, 6, 7, 8, 10, 17, 18, 19, 20, 21, 

13 or 14 

22, 23, 24, 25, 26, 27, 28, 29, 30 or 31 

11, 12 or 32 9 

234c/03 ExcluDoor 4 6, 7, 8, 15, 16, 17, 18, 19 or 30 N/A 

234c/04 ExcluDoor 3 1 or 2 N/A 

234c/05 ExcluDoor 4 9 3 or 4 1 N/A 

234c/06 ExcluDoor 4 1, 2, 20, 21, 22, 23, 24, 25, 26, 27, 28 or 29 N/A 

234c/07 ExcluDoor 4 F.R. 7 13 or 14 

234c/08 ExcluDoor 4 F.R. 7 N/A 


360 20 Nov 2011

Compatible 

Locking 

System 



Locking System Type Com patible Operating Devices Compatible 

Cylinders 


1 Assa765 Sash lock Key Key 2 or 

Thumbturn 5 Blind 

rose 

A to D 

2 Assa 2788 Dead lock Key Key 2 B or D 

3 

Assa 765 3 Sash lock Key Thumbturn A or C 

Assa 2788 4 Deadlock Key Blind rose A or C 

4 



5 Assa Mico 942-10 2-w ay panic exit device None Push pad N/A 

6 Assa Mico 942-3p 3-w ay panic exit device None Push pad N/A 

7 Surelock McGill EX210 (B1) 3-w ay panic exit device None Panic bar N/A 

8 Surelock McGill EX210 (B1) 3-w ay panic exit device Key and handle 

(LEO L1P) 

Panic bar 

S to W 

9 Surelock McGill EX212 (B2) 2-w ay panic exit device None Panic bar N/A 

10 Surelock McGill EX212 (B2) 2-w ay panic exit device Key and handle Panic bar 

S to W 

(LEO L1P) 

11 Surelock McGill EX213 (B3) 3-bolt panic exit device None Panic bar N/A 

12 Surelock McGill EX213 (B3) 3-bolt panic exit device Key and handle Panic bar 

S to W 

(LEO L1P) 

13 Sunray “D/40083” internal Tw o concealed leading N/A N/A N/A 

drop bolt 

edge drop bolts 

14 Sunray “D/40015” surface Tw o surface mounted high N/A N/A N/A 

mounted drop bolt 

security barrel bolts 

15 Surelock McGill A1 3-w ay locking device None Handle N/A 

16 Surelock McGill A1 3-w ay locking device Key and handle Handle 

S to W 

(LEO L1P) 

17 Surelock McGill D3- K13P5 6 3-w ay locking device Key and handle Handle E to R 

18 Surelock McGill D6 K13P5 6 3-w ay locking device Key and handle Handle E to R 

19 Surelock McGill C1 K13P5 6 3-w ay locking device Key and handle Handle E to R 

20 EX800 Single point emergency exit None Handle N/A 

device 

21 EX800 w ith K13P5 option Single point emergency exit Key and handle Handle E to R 

device 

22 DL800 Single point deadlock None Thumb turn and N/A 

handle 

23 DL800 w ith K13P5 option Single point deadlock Key and handle Thumb turn and E to R 

handle 

24 DL800 w ith K13P5 option Single point deadlock None Break dome 

N/A 

protection turn 

knob and handle 

25 DL800 w ith K4 and K13P5 

option 

Single point deadlock Key and handle Break dome 



E to R 

20 Nov 2011 361



26 AC800 Single point electromechanical 


lock pow ered by 12V, 24V 

or 50 V solenoid 7, 8 

27 AC800 w ith X option Single point electromechanical 




28 AC800 w ith K13P5 option Single point electromechanical 




29 AC800 w ith K13P5 and K9 

options 

Single point electromechanical 




Handle plus 

external access 

control entry 

device (e.g. key 

pad or sw ipe 

card etc) 

Handle plus 


control entry 


pad or sw ipe 

card etc) 

Handle plus 


control entry 


pad or sw ipe 

card etc) 

Handle plus 


control entry 


pad or sw ipe 

card etc) 


(LEO L2) 


(LEO L2) 

32 Surelock McGill EX213 (B3) 3-bolt panic exit device Key and handle 

(LEO L2) 


Handle 

Handle 

Handle 

Handle and 

thumbturn 

Panic bar 

Panic bar 

Panic bar 

N/A 

N/A 

E to R 

E to R 

T to AE 

T to AE 

T to AE 


Reference 

A Assa 601 Oval profile cylinder 

B Assa 602 Oval profile cylinder 

C Assa Tw in Combi C5801 Oval profile cylinder 

D Assa Tw in Combi C5802 Oval profile cylinder 

E Abloy CY405DP Rim cylinder 

F Abloy CY405PT Rim cylinder 

G Assa 4857 Rim cylinder 

H Assa C5857 Rim cylinder 

I Assa Ruko Flexcore - F557 Rim cylinder 

J Bramah C17 Rim cylinder 

K Dom 555ix10G Rim cylinder 

L Kaba KV06.100 Rim cylinder 

M Medeco BX668 Rim cylinder 

N Medico M3 ARX Rim cylinder 

O Union 1x1 Rim cylinder 

P Yale 1109.SCP Rim cylinder 

Q AMS CL-OVLD 11 Scandinavian oval profile mechatronic cylinder 

R AMS CL-CA2D 11 Finnish Round profile mechatronic cylinder 

S Winkhaus VS629 Screw -in cylinder 

T Union 26x11B Screw -in cylinder 

U Abloy CY404DP Screw -in cylinder 

362 20 Nov 2011

V Abloy CY404PT Screw -in cylinder 

W Assa Tw in-Combi C5851 Screw -in cylinder 

X Assa 4851 Screw -in cylinder 

Y Assa F551 Screw -in cylinder 

Z Bramah C17SI Screw -in cylinder 

AA Dom 419ix10KG Screw -in cylinder 

AB Kaba K207.203 C5-SC Screw -in cylinder 

AC Medico 664 Screw -in cylinder 

AD Medico M3ARX MOTC-1001 Screw -in cylinder 

AE Yale PK1133 ProKey Screw -in cylinder 



Notes: 

1. In order to achieve the required security rating, both locks must be activated. 

2. The security rating will not be achieved if the key is left in the lock on the inside of the door or if the door is placed in the emergency 

exit mode. 

3. Lock fitted to the upper lock position. 

4. Lock fitted to the lower lock position. 

5. The D/40047/L thumbturn protection shroud shall be fitted when this hardware is fitted to the ExcluDoor 4 double doorset. 

6. Device must be deadlocked if the doorset is to provide resistance to attack commensurate with Security Rating 4. 


8. The resistance of the access control locks to “non-mechanical” attack has not been assessed as it is outside the scope of LPS1175. 



and system configurations that may be used with these locking systems is “infinite”. It is therefore recommended that Sunray 

Engineering satisfy themselves that the components used are either resistant to mechanical and other forms of tampering/abuse, or 

that they are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may 

cause the locking system to disengage. 

9. The ExcluDoor 4 single leaf doorset (certificate number 234c/05) is also certified for 30 minutes integrity against the requirements of 

LPS1056: Issue 5. See LPCB Certificate No. 234b or Volume 2, Part 2, Section 1.1 of the Red Book for details. 

10. The ExcluDoor 4 double leaf doorset can be produced with leafs of unequal width. The maximum width of both leaves is 1173.5 mm. 

The minimum width of active leaf approved is 615 mm and the minimum width of passive leaf approved is 300 mm. 

11. The resistance of the mechatronic cylinders to “non-mechanical” attack has not been assessed as it is outside the scope of LPS 

1175. Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and performance of 

ancillary equipment that may be used in conjunction with those cylinders. It is therefore recommended that specifiers satisfy 

themselves that the components used are either resistant to electronic methods of attack, or that they are suitably protected from 

such tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking system to 

disengage. 




Clear 

Opening 

Height 

(m) 

ExcluDoor 3 Mk2 Single leaf, outward opening hinged 



ExecDoor 2 

ExcluDoor 4 Mk2 


F.R. 

ExcluDoor 5 


Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.8 2.4 0.75 1.24 3 234d/01 

1 1.8 2.4 1.24 2.4 3 234d/02 

Single leaf, outward opening hinged 1.8 2.2 0.75 1.3 2 234d/03 


Double leaf, outward opening 1.8 2.2 1.5 2.5 2 234d/04 


Single leaf, outward opening hinged 1.8 2.4 0.75 1.24 4 234d/05 


Double leaf, outward opening 1.8 2.4 1.24 2.4 4 234d/06 














20 Nov 2011 363




Clear 

Opening 

Height 

(m) 


F.R. 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 




hinged security doorset 3 1.8 2.4 1.24 2.4 3 234d/14 

Cert. 

No. 


LPCB Ref. 

No. 

Product Name Type Compatible Locking Systems 

Active Leaf 

Passive Leaf 

234d/01 ExcluDoor 3 Mk2 Single leaf, outw ard opening hinged security doorset 1 to 51 - 

234d/02 ExcluDoor 3 Mk2 Double leaf, outw ard opening hinged security doorset 1 to 51 52 or 53 

234d/03 ExecDoor 2 Single leaf outw ard opening hinged security doorset 54 to 60 - 

234d/04 ExecDoor 2 Double leaf outw ard opening hinged security doorset 54 to 60 61 or 62 

234d/05 ExcluDoor 4 Mk2 Single leaf, outw ard opening hinged security doorset 63 to 80 N/A 


234d/07 ExcluDoor 4 Mk2 F.R. Single leaf, outw ard opening hinged security doorset 63 to 71 N/A 

234d/08 ExcluDoor 4 Mk2 F.R. Double leaf, outw ard opening hinged security doorset 63 to 71 52 or 53 

234d/09 ExcluDoor 5 Single leaf, outw ard opening hinged security doorset 81 to 102 N/A 

234d/10 ExcluDoor 5 Double leaf, outw ard opening hinged security doorset 81 to 102 52 or 53 

234d/11 ExcluDoor 4 Mk3 Single leaf, outw ard opening hinged security doorset 81 to 102 N/A 


234d/13 ExcluDoor 3 Mk3 F.R. Single leaf, outw ard opening hinged security doorset 63 to 71 N/A 

234d/14 ExcluDoor 3 Mk3 F.R. Double leaf, outw ard opening hinged security doorset 63 to 71 52 or 53 


Compatible 

Locking 

Systems 

Manufacturer Model Type Com patible Operating Devices 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 

External Face 

Internal Face 

Stirling EX800 Single point emergency 

exit device 

None Handle N/A 

Stirling EX800 w ith Single point emergency Key and handle Handle Z, AB to AI, 

K13P option exit device 

AX 

Stirling DL800 Single point deadlock None Thumb turn and N/A 

handle 

Stirling DL800 w ith Single point deadlock Key and handle Thumb turn and Z, AB to AI, 

K13P option 

handle 

AX 

Stirling DL800 w ith Single point deadlock None Break dome N/A 

K4 option 



Stirling DL800 w ith 

K4 and K13P 

option 

Single point deadlock Key and handle Break dome 



Compatible 

Cylinders 

Z, AB to AI, 

AX 

364 20 Nov 2011


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 

Stirling AC800 

Stirling AC800 w ith 

X option 


K13P option 


K13P and K9 

options 

Slimline 

SL305-00-H3 

Slimline 

SL304-00 

Slimline 

SL305-0x-H3Lon 

Slimline 

SL304-0x-Lon 

Slimline 

SL324-0x- 

K2OnPRn 

Slimline 

SL325-0x- 

H3K2OnPRn 

Slimline 

SL325-0x- 

K2OnPRn 




access 

control lock pow ered 

by 12V, 24V or 50V 

solenoid 5 


access 


by 12V, 24V or 50V 

solenoid 5 


access 


by 12V, 24V or 50V 

solenoid 5 


access 


by 12V, 24V or 50V 

solenoid 5 

Handle plus 


control entry 


pad or sw ipe 

card etc) 6 Handle N/A 

Handle plus Handle N/A 

card etc) 6 


control entry 


pad or sw ipe 

Handle and key Handle Z, AB to AI, 

sw ipe card etc.) 6 

or external 

AX 


entry device 

(e.g. key pad or 

Handle and key 

or external 


entry device 



Handle and 

thumb turn 

Z, AB to AI, 

AX 

3-w ay emergency exit None Push pad N/A 

device 

3-w ay panic exit device None Panic bar N/A 

3-w ay emergency exit 

device 

Key and handle 

(LEO L1P) 

Push pad 

BB, BC, BE, 

BI 

3-w ay panic exit device Key and handle 

(LEO L1P) 

Panic bar BB, BC, BE, 

BI 

3-w ay panic exit device Handle and key Panic bar Z, AB to AI, 


w ith electro-mechanical or external 

AX 

access control lock access control 

pow ered by 12 V, 24 V entry device 

or 50 V solenoid 5 (e.g. key pad or 


device w ith electromechanical 

access 


by 12 V, 24 V or 50 V 

solenoid 5 


device w ith electromechanical 

access 


by 12 V, 24 V or 50 V 

solenoid 5 


or external 


entry device 


sw ipe card etc.) 6 Push pad Z, AB to AI, 

AX 


or external 


entry device 


sw ipe card etc.) 6 Handle Z, AB to AI, 

AX 

20 Nov 2011 365




Limited 


Limited 

20 Tindall 


21 Tindall 


22 Tindall 


23 Tindall 


24 Tindall 


25 Tindall 


26 Tindall 


27 Tindall 


28 Tindall 


29 Tindall 


30 Tindall 


31 Tindall 


32 Tindall 


33 Tindall 


34 Tindall 


35 Tindall 


36 Tindall 


37 Tindall 


38 Tindall 


Slimline 

SL305-0x-H3L2on 


device 


(LEO L2) 

Push pad BB to BH 

Slimline 3-w ay panic exit device Key and handle Panic bar BB to BH 

SL304-0x-L2on 

(LEO L2) 

Mico 942 / ELK 3 2-w ay panic exit device Key and handle Panic bar AM to AZ 

(ELK3) 

Mico 942 2-w ay panic exit device None Panic bar N/A 

Mico 942P / ELK 3 2-w ay emergency exit 

device 


(ELK3) 

Push pad AM to AZ 

Mico 942P 2-w ay emergency exit None Push pad N/A 

device 

Mico 942L / ELK 3 2-w ay emergency exit Key and handle Lever handle AM to AZ 

device 

(ELK3) 

Mico 942L 2-w ay emergency exit None Lever handle N/A 

device 

Mico 942L INT AD 2-w ay locking system None Thumb turn and N/A 

w ith automatic deadlock 

lever handle 

Mico 942 INT MD 

Mico 942P INT MD 

Mico 942L INT MD 







None 

None 

None 


full w idth push 

plate 7 


push pad 


lever handle 

Mico 942-3 / ELK 3 3-w ay panic exit device Key and handle 

(ELK3) 

Panic bar AM to AZ 

Mico 942-3 3-w ay panic exit device None Panic bar N/A 

Mico 942-3P / ELK 

3 


device 


(ELK3) 

Push pad AM to AZ 

Mico 942-3P 3-w ay emergency exit None Push pad N/A 

device 

Mico 942-3L / ELK 3-w ay emergency exit Key and handle Lever handle AM to AZ 

3 

device 

(ELK3) 

Mico 942-3L 3-w ay emergency exit None Lever handle N/A 

device 

Mico 942-3L INT 3-w ay locking system None Thumb turn and N/A 

AD w ith automatic deadlock 

lever handle 

Mico 942-3 INT MD 3-w ay locking system None Thumb turn and N/A 


full w idth push 

plate 7 

Mico 942-3P INT 3-w ay locking system None Thumb turn and N/A 

MD w ith manual deadlock 

push pad 

N/A 

N/A 

N/A 

366 20 Nov 2011



39 Tindall 


40 Tindall 


41 Tindall 


42 Tindall 


43 Tindall 


44 Tindall 


45 Tindall 


46 Tindall 


47 Tindall 


48 Tindall 


49 Tindall 


50 Tindall 


51 Tindall 



MD 

Mico 942 EM SEC 

Mico 942P EM SEC 

Mico 942L EM SEC 

Mico 942 SATE EM 

SEC 

Mico 942P SATE 

EM SEC 

Mico 942L SATE 

EM SEC 

Mico 942-3 EM SEC 


SEC 


SEC 


EM SEC 

Mico 942-3P SATE 

EM SEC 

Mico 942-3L SATE 

EM SEC 




w ith automatic deadlock 

None 

Access control 

system and lever 

handle 5,6 

2-w ay locking system Access control 

w ith automatic deadlock system and lever 

handle 5,6 

2-w ay locking system Access control 

w ith automatic deadlock system and lever 

handle 5,6 

2-w ay panic exit device 


deadlocking 


device w ith automatic 

deadlocking 



deadlocking 



deadlocking 



deadlocking 



deadlocking 

3-w ay panic exit device 


deadlocking 



deadlocking 



deadlocking 


lever handle 


and thumb turn 

override w ith full 

w idth push plate 7 



override w ith 

push pad 




lever handle 

N/A 

N/A 

N/A 

N/A 

Access control Panic bar N/A 

handle 5,6 


Access control Push pad N/A 

handle 5,6 


Access control Lever handle N/A 

handle 5,6 




handle 5,6 



handle 5,6 



handle 5,6 



override w ith full 

w idth push plate 7 




push pad 




lever handle 

N/A 

N/A 

N/A 

Access control Panic bar N/A 

handle 5,6 




handle 5,6 Push pad N/A 

Access control Lever handle N/A 

handle 5,6 


20 Nov 2011 367



52 Sunray 


Sunray surface 


Tw o surface mounted 

drop bolts 

None 


drop bolts 

53 Sunray Sunray internal Tw o internal drop bolts None Internal drop N/A 

Engineering Ltd drop bolts 

bolts 

54 Assa 765 Sash lock Key and lever Key and lever BA 

handle 

handle 

55 Assa 765 Sash lock Key and lever Thumbturn and AS 


56 Assa 2788 Dead lock Key Key BA 

57 Assa 2788 Dead lock Key Thumbturn AS 

58 Exidor 803 Three point panic exit 

device 8 None Panic bar N/A 







Key and turn 

knob (Exidor 

809) 


(Exidor 810) 

Panic bar 

Panic bar 

None Panic bar N/A 

61 Exidor 802 Tw o point panic exit 

device 9 

62 Exidor HS923/10 Tw o tow er bolts None Tow er bolts N/A 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 

Slimline SL301 Three point deadlock None Internal key and 

handle 

N/A 

Slimline SL303 Three point deadlock None Thumb turn and N/A 

handle (K4 breakdome 

optional) 

Slimline SL305 Three point emergency None Handle N/A 

exit device 

Slimline SL311-P5 Three point deadlock Key and lever Internal key and Z, AB to AI, 

handle 

handle 

AX 

Slimline SL313-P5 Three point deadlock Key and lever 

handle 

Slimline SL315-P5 



Three point emergency 

exit device 

Three point deadlock 

incorporating electromechanical 

access 


by 12V, 24V or 50V 

solenoid 5,6 



access 


by 12V, 24V or 50V 

solenoid 5,6 

Key and lever 

handle 

Handle plus 


control entry 

device and key 

override 

Handle plus 


control entry 


override 



optional) 

Handle 

Internal key/ 


and handle 

Thumb turn/ 


and handle (K4 

break-dome 

optional) 

N/A 

Y 

Y 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

368 20 Nov 2011




Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Limited 


Three point emergency 

exit device 


access 


by 12V, 24V or 50V 

solenoid 5,6 

Handle plus 


control entry 


override 

Handle 

Z, AB to AI, 

AX 

Stirling ST101 Single point deadlock None Internal key and 

handle 

N/A 

Stirling ST103 Single point deadlock None Thumb turn and N/A 


optional) 

Stirling ST105 Single point emergency None Handle N/A 

exit device 

Stirling ST111-P5 Single point deadlock Key and lever Internal key and Z, AB to AI, 

handle 

handle 

AX 

Stirling ST113-P5 Single point deadlock Key and lever Thumb turn and Z, AB to AI, 

handle handle (K4 breakdome 

AX 

optional) 

Stirling ST115-P5 Single point emergency 

exit device 

Key and lever 

handle 

Handle 

Stirling ST121-P5 Single point deadlock Handle plus Internal key/ 


external access access control 

access control entry and handle 

control lock pow ered device and key 

by 12V, 24V or 50V override 

solenoid 5,6 

Stirling ST123-P5 Single point deadlock Handle plus Thumb turn/ 


external access access control 

access control entry and handle (K4 

control lock pow ered device and key break-dome 

by 12V, 24V or 50V override optional) 

solenoid 5,6 

Stirling ST125-P5 Single point emergency Handle plus Handle 

exit device external access 


control entry 

access device and key 

control lock pow ered override 

by 12V, 24V or 50V 

solenoid 5,6 

Slimline SL305 Three point emergency 

exit device 

Slimline SL303 Three point deadlock None Thumb turn and 


optional) 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 


N/A 


Limited 


Limited 

Slimline SL301 Three point deadlock None Internal key and 

handle 

Slimline SL315-P6 Three point emergency Key and lever Handle 

exit device 

handle 

N/A 

Z, AB to AI, 

AX 

20 Nov 2011 369




Limited 


handle 



optional) 

Z, AB to AI, 

AX 


Limited 


Limited 


Limited 


Limited 

90 Tindall 


91 Tindall 


92 Tindall 


93 Tindall 


94 Tindall 


95 Tindall 


96 Tindall 


97 Tindall 


98 Tindall 



handle 

Slimline SL325-P6 Three point emergency Handle plus 

exit device external access 


control entry 

access device and key 

control lock pow ered override 

by 12V, 24V or 50V 

solenoid 5.6 



Abryll PE3 



access 


by 12V, 24V or 50V 

solenoid 5.6 



access 


by 12V, 24V or 50V 

solenoid 5.6 

Single point emergency 

exit device 

Handle plus 


control entry 


override 

Handle plus 


control entry 


override 

Internal key and 

handle 

Handle 

Thumb turn/ 


and handle (K4 

break-dome 

optional) 

Internal key/ 


and handle 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 

Z, AB to AI, 

AX 


Abryll AD3 Single point deadlock None Thumb turn and 

handle 

Abryll EPC AD3 Single point deadlock None Internal key and 

handle 

Abryll SATE AD3 Single point emergency Key and lever Handle 

USCH5 

exit device 

handle 

Abryll SATE EPC Single point emergency Key and lever Handle 

AD3 USCH5 exit device 

handle 

Abryll AD3 USCH5 Single point deadlock Key and lever Thumb turn and 

handle 

handle 

Abryll EPC AD3 Single point deadlock Key and lever Thumb turn and 

USCH5 

handle 

handle 

Abryll EPC AD3 Single point deadlock Key and lever Internal key and 

USCH5 

handle 

handle 

Abryll SATE EM3 

Handle 

USCH5 


exit device 


access 


by 12V, 24V or 50V 

solenoid 5.6 

Handle plus 


control entry 


override 

N/A 

A to K 

Z, AA, AH to 

AL, AN to AZ 

A to K 

Z, AA, AH to 

AL, AN to AZ 

L to X 

A to K 

Z, AA, AH to 

AL, AN to AZ 

370 20 Nov 2011



99 Tindall 


100 Tindall 


101 Tindall 


102 Tindall 


Abryll EPC SATE 

EM3 USCH5 

Abryll EPC EM3 

USCH5 

Abryll EM3 USCH5 

Abryll EPC EM3 

USCH5 


exit device 


access 


by 12V, 24V or 50V 

solenoid 5.6 

Single point deadlock 


access 


by 12V, 24V or 50V 

solenoid 5.6 



access 


by 12V, 24V or 50V 

solenoid 5.6 



access 


by 12V, 24V or 50V 

solenoid 5.6 

Handle plus 


control entry 


override 

Handle plus 


control entry 


override 

Handle plus 


control entry 


override 

Handle plus 


control entry 


override 

Handle 

Thumb turn/ 


and handle 

Thumb turn/ 


and handle 

Internal key/ 


and handle 

A to K 

L to X 

Z, AA, AH to 

AL, AN to AZ 

A to K 


Cylinder Manufacturer Model Type ‘Plus’ 

Reference 

rating 10 

A Abloy CY304 Protec Europrofile double cylinder (key:key) + 

B Access2 Tigres Omega Europrofile double cylinder (key:key) + 

C Assa 4822 Europrofile double cylinder (key:key) 

D Assa 7622 Europrofile double cylinder (key:key) 

E Assa C5822 Europrofile double cylinder (key:key) 

F Assa dp4422 Europrofile double cylinder (key:key) 

G Kaba Gege RAM Europrofile double cylinder (key:key) + 

H Kaba Quattro PluS Europrofile double cylinder (key:key) + 

I Medeco M3-ARX Europrofile double cylinder (key:key) + 

J Abloy CY304 Protec Cliq 11 Europrofile double cylinder (key:key) (mechatronic) + 

K Assa 44M22 Cliq 11 Europrofile double cylinder (key:key) (mechatronic) 

L Abloy CY305 Protec Europrofile double cylinder (key:thumbturn) + 

20 Nov 2011 371



M Abloy CY333 Protec (PT) Europrofile double cylinder (key:thumbturn) + 

N Access2 Tigres Omega Europrofile double cylinder (key:thumbturn) + 

O Assa 4827 Europrofile double cylinder (key:thumbturn) 

P Assa 7627 Europrofile double cylinder (key:thumbturn) 

Q Assa 44M27 Cliq 11 Europrofile double cylinder (key:thumbturn) 

R Assa C5827 Europrofile double cylinder (key:thumbturn) 

S Assa dp4427 Europrofile double cylinder (key:thumbturn) 

T Kaba Gege RAM Europrofile double cylinder (key:thumbturn) + 

U Kaba Quattro PluS Europrofile double cylinder (key:thumbturn) + 

V Medeco M3-ARX Europrofile double cylinder (key:thumbturn) + 

W Abloy CY305 Protec Cliq 11 Europrofile double cylinder (key:thumbturn) 

(mechatronic) 

X Abloy CY333 Protec Cliq 11 Europrofile double cylinder (key:thumbturn) 

(mechatronic) 

Y Zone 1850 Europrofile single cylinder 

Z AMS CL-CA2D 11 Finnish Round cylinder (mechatronic) + 

AA Abloy CY403 Protec Rim cylinder + 

AB Abloy CY405 Disklock Pro (DP) Rim cylinder + 

AC Abloy CY405 ProTec (PT) Rim cylinder + 

AD Assa 4857 Rim cylinder 

AE Assa C5857 Rim cylinder 

AF Bramah C17 Rim cylinder 

AG Kaba K20 Rim cylinder 

AH Kaba Quattro PluS Rim cylinder + 

AI Medico M3ARX Rim cylinder + 

AJ Abloy CY403 Protec Cliq 11 Rim cylinder (mechatronic) + 

AK Assa 4857 Round threaded cylinder 

AL Assa C5857 Round threaded cylinder 

AM Abloy CY201 Disklock Pro (DP) Scandinavian Oval cylinder + 

AN Abloy CY201 Protec (PT) Scandinavian Oval cylinder + 

AO Abloy CY201 Protec Cliq 11 Scandinavian Oval cylinder + 

AP Access2 Tigres Omega Scandinavian Oval cylinder + 

AQ Assa 4801 Scandinavian Oval cylinder 

AR Assa 7601 Scandinavian Oval cylinder 

AS Assa C5801 Scandinavian Oval cylinder 

AT Assa dp4401 Scandinavian Oval cylinder 

AU Kaba K20 Scandinavian Oval cylinder 

AV Kaba Quattro PluS Scandinavian Oval cylinder + 

AW Medeco M3-ARX Scandinavian Oval cylinder + 

AX AMS CL-OVLD 11 Scandinavian Oval cylinder (mechatronic) + 

AY Assa 4401 Cliq 11 Scandinavian Oval cylinder (mechatronic) 

AZ Locken CL-PL2WR 11 Scandinavian Oval cylinder (mechatronic) + 

BA Assa C5802 Scandinavian Oval double cylinder (key:key) 

BB Abloy CY404 Disklock Pro (DP) Screw -in cylinder + 

+ 

+ 

372 20 Nov 2011



BC Abloy CY404 Protec (PT) Screw -in cylinder + 

BD Assa 4851 Screw -in cylinder 

BE Assa C5851 Screw -in cylinder 

BF Bramah C17SI Screw -in cylinder 

BG Kaba K207.203 C5-SC Screw -in cylinder 

BH Medico M3ARX MOTC-1001 Screw -in cylinder + 

BI Winkhaus VS629 Screw -in cylinder 

Accessories 

Accessory Description Certificate number of associated doorset (234d/##) 

Full frame 

threshold 

Low level 

threshold w ith 

stop 

Low level 

threshold 

Central Tego 

vision panel 

Offset Tego 

vision panel 

Vistamatic 

Sherman 

vision panel 12 

Vistamatic 

Chieftain vision 

panel 12 

01 02 03 04 05 06 07 08 09 10 11 12 13 14 

Full frame threshold 

Low level threshold w ith stop 

Low level threshold 

200 mm (w ide) by 300 mm (high) 

vision panel formed using Tego S46 

glazing units located in the centre 

(w idth) of the leaf at a height 

betw een 1464.5 and 1614.5 mm up 

from the bottom of the leaf. 


vision panel formed using Tego S46 

glazing units located betw een the 

centre of the leaf and leading 

edge 11 at a height betw een 1464.5 

and 1614.5 mm up from the bottom 

of the leaf. 

40.5 mm thick vision panels of 

maximum dimensions 400 mm by 

400 mm. These may either be 

located central to the w idth of the 

leaf or offset from leading edge by 

150 mm. 

27.8 mm thick vision panels of 





150 mm. 

 

 

 

 

 

 

 

 

20 Nov 2011 373



AB26 vision 

panel 

27 mm thick vision panels of 





150 mm. 

 

 

Tecdur vision 

panel 


vision panel formed using Tecdur 

DC49MS glazing units incorporating 

steel grids located in the centre 

(w idth) of the leaf at a height 

betw een 1464.5 and 1614.5 mm 

from the bottom of the leaf to the 

centre of the vision panel. 

 

 

ExcluVent 3 

louvre panels 


louvre panels located central to the 

w idth of the leaf in the top half of 

the leaf, in the bottom half of the 

leaf, or in both top and bottom half’s 

of the leaf. 

 

 

ExcluVent 4 

louvre panels 






of the leaf. 

 

 

ExcluVent 5 

louvre panels 






of the leaf. 

 

The following table confirms which combinations of vision panel, louvre panel, threshold and locking system may be used together. 

Accessory 

ExcluVent 3 

louvre panel 

located in the 

top half of the 

leaf 

ExcluDoor 3 Mk2 doorset ExecDoor 2 

doorset 

Full Frame 

Threshold 

Low Level 

Threshold 

With Stop 

Low Level 

Threshold 

1 to 53 1 to 53 1 to 11, 13, 

16 to 18, 22 

to 29, 32 to 

42, 44 to 48, 

50 to 53 

Com patible locking systems 

ExcluDoor 4 ExcluDoor 4 ExcluDoor 5 

Mk2 Mk2 F.R. doorset Mk3 

doorset and with any 

w ith any ExcluDoor 3 threshold 

threshold Mk3 F.R. 

option doorsets 

w ith any 

threshold 

option 

N/A N/A N/A N/A N/A 

ExcluDoor 4 

doorset 

with any 

option 14 threshold 

option 

374 20 Nov 2011

ExcluVent 3 

louvre panel 


bottom half of 

the leaf 

ExcluVent 3 

louvre panels 


top and bottom 

halves of the 

leaf 



1 to 53 1 to 53 1 to 53 N/A N/A N/A N/A N/A 

1 to 11, 13, 

16 to 18, 22 

to 29, 32 to 

42, 44 to 48, 

50 to 53 

1 to 11, 13, 

16 to 18, 22 

to 29, 32 to 

42, 44 to 48, 

50 to 53 

1 to 11, 13, 

16 to 18, 22 

to 29, 32 to 

42, 44 to 48, 

50 to 53 

ExcluVent 4 N/A N/A N/A N/A 52, 53, 63 to 

louvre panels 15 80 


N/A N/A N/A 

ExcluVent 5 N/A N/A N/A N/A N/A N/A 52, 53, 83, 

louvre panels 15 86, 89, 92, 

97, 102 

Central and 

Offset Tego 

vision panels 

Vistamatic 

Sherman vision 

panel 

Vistamatic 

Chieftain vision 

panel 

AB26 vision 

panel 

Tecdur vision 

panel 

52, 53, 83, 

86, 89, 92, 

97, 102 

1 to 53 1 to 53 1 to 11, 13, 

16 to 18, 22 

to 29, 32 to 

42, 44 to 48, 

50 to 53 


N/A N/A N/A 54 to 62 N/A N/A N/A N/A 

N/A N/A N/A 54, 56, 62 N/A N/A N/A N/A 

N/A N/A N/A 54 to 62 N/A N/A N/A N/A 

N/A N/A N/A N/A 52, 53, 63 to 

80 

N/A N/A N/A 

Notes: 

1. The ExcluDoor 3 Mk2 double leaf doorset can be produced with leafs of unequal width. The maximum width of both leaves is 1173.5 

mm. The minimum width of active leaves approved is 615 mm. The minimum width of passive leaves approved is 300 mm (plain 

leaves) and 500 mm (leaves incorporating vision panels). 

2. The ExecDoor 2 double leaf doorsets may incorporate leafs of equal or unequal width. Leafs of unequal width will comprise of an 

active leaf exactly twice as wide as the passive leaf. The maximum leaf width is 1350 mm and the minimum leaf width is 500 mm. 

3. The ExcluDoor 4 Mk2, ExcluDoor 4 Mk2 F.R. and ExcluDoor 3 Mk3 F.R. double leaf doorsets can be produced with leafs of equal 

and unequal width, with the leaf width being within the following range: 

a. Active leaf width between 615 mm and 1169.5 mm (excluding the astragal). 

b. Passive leaf width between 220.5 mm and 1714 mm (excluding the astragal). 

4. The ExcluDoor 5 and ExcluDoor 4 Mk3 double leaf doorsets can be produced with leafs of equal and unequal width, with the leaf 

width being within the following range: 

a. Active leaf width between 615 mm and 1169.5 mm (excluding the astragal). 

b. Passive leaf width between 470 mm and 1714 mm (excluding the astragal). 





and system configurations that may be used with these locking systems is “infinite”. It is therefore recommended that Sunray 

Engineering satisfy themselves that the components used are either resistant to mechanical and other forms of tampering/abuse, or 

that they are suitably protected from such tampering/abuse and are resistant to any environmental conditions/interference that may 

cause the locking system to disengage. 



panic or emergency exit device unless the deadlock is automatically operated by the action of the panic or exit device. For further 

information, please refer to the appropriate standards for emergency and panic exit devices, i.e. BS EN 179 and BS EN 1125 

respectively. 

8. Locking systems 58, 59 and 60 may not comply with fire escape regulations relating to potential panic situations if fitted to double leaf 

doorsets. This is because activation of the device on one leaf may not necessarily release the other leaf and in some cases may not 

release the leaf to which it is fitted. 

9. This locking system may only be used on the passive leaf and then only if locking systems 58, 59 and 60 are used on the active leaf. 

10. A ‘Plus’ rating demonstrates that the cylinder meets the requirements defined in Annex A of BS 3621: 2007 or manipulation 

resistance class ‘1’ defined in LPS 1242: Issue 2. 

11. The resistance of the mechatronic cylinders to “non-mechanical” attack has not been assessed as it is outside the scope of LPS 

1175. Likewise, the approval does not cover possible effects of any susceptibilities relating to the functionality and performance of 

20 Nov 2011 375



ancillary equipment that may be used in conjunction with those cylinders. It is therefore recommended that specifiers satisfy 

themselves that the components used are either resistant to electronic methods of attack, or that they are suitably protected from 

such tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking system to 

disengage. 

12. The horizontal position of the offset vision panels depends on the locking hardware fitted. Please refer to the manufacturer for more 

details. 

13. The Vistamatic vision panels incorporate obscurable panels controlled by a handle on the protected side of the doorset. 

14. The ExcluDoor 5 double leaf doorsets incorporating ExcluVent 5 louvre panels achieve Security Rating 4 when placed in the 

minimum locked condition and incorporating locking systems 92, 97 and 102 on the active leaf and locking system 52 on the passive 

leaf. All other ExcluDoor 5 double leaf doorsets incorporating ExcluVent 5 louvre panels achieve Security Rating 5 when placed in the 

minimum locked condition. 

15. The ExcluVent 4 and ExcluVent 5 louvre panels were compatible with the locking options listed when the louvre panels were located 

in the top half of the leaf only, the bottom half of the leaf only, or in both the top and bottom halves of the leaf. 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 





Clear 

Opening 

Height 

(m) 

UltraSecure DS1/DV4 Single leaf hinged 



UltraSecure DS2/DV4 Double leaf hinged 



Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

0.9 2.9 0.5 1.3 4 450a/03 

0.9 2.9 1.2 2.6 4 450a/08 


Padlock Designation 

Cylinder 

UltraSecure Doorset (LPCB 

Ref. No. 450a/……) 

03 08 

Abloy PL240/25 Abloy High profile 














376 20 Nov 2011















Chubb 1K23c Chubb 6-pin cylinder 




Kaba Thorlock 4 Kaba 20 

Rotalok 60/12/SE Kaba 20 (Armoured) 3 

Rotalok 60/12/SE Kaba 20 (Standard) 3 




Rotalok 60/12/ST-T027 Assa Twin-Combi 


Rotalok 60/12/ST Kaba 20 (Standard) 3 

Accessories 

Accessory 

UltraSecure Doorset 

(LPCB Ref. No. 450a/……) 

03 08 

Arched profile 

K1 staple 4 

Louver option 1 

Louver option 2 

Narrow frame 

Shallow threshold 

Notes 



1. Certification does not cover the use of padlocks other than those listed above. Utilisation of unlisted padlocks and/or accessories 

may affect the level of security offered by the door set. 

2. The ‘user friendliness’ of employing the padlocks listed above has not been assessed as this is beyond the scope of LPS 1175: 

Issue 5. 


4. K1 staple is used in conjunction with the Kaba Thorlock fitted with a Kaba 20 cylinder. 

5. The use of the locking override system is outside the scope of the LPCB approval. 




Clear 

Opening 

Height 

(m) 

Ultra Secure DS1/DV3 Single leaf hinged 



Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

0.9 2.9 0.5 1.3 3 450d/01 

20 Nov 2011 377




Clear 

Opening 

Height 

(m) 

Ultra Secure DS1/LS3 Single leaf hinged 



Ultra Secure DS2/DV3 Double leaf hinged 



Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

0.9 2.3 0.5 1.1 3 450d/02 

0.9 2.9 1.2 2.6 3 450d/03 

Compatible locking devices 

Locking Device Type 

Cylinder 

Ultra Secure Doorsets 

(LPCB Ref. No. 450d/..) 

01 02 03 

Abloy PL240/25 Padlock Abloy High Profile 

Abloy PL240/25EX Padlock Abloy Exec 

Abloy PL240/25DP Padlock Abloy Disklock Pro 

Abloy PL240/25PT Padlock Abloy Protec 

Abloy PL242 Padlock Abloy High Profile 

Abloy PL242EX Padlock Abloy Exec 

Abloy PL242DP Padlock Abloy Disklock Pro 

Abloy PL242PT Padlock Abloy Protec 

















Chubb 1K23c Padlock Chubb 6-pin cylinder 

Kaba KP15.0000C5-RB Padlock Kaba 20 (Armoured) 3 

Kaba K20SS65L Padlock Kaba 20 (Armoured) 3 

378 20 Nov 2011



Kaba K20SS65CL Padlock Kaba 20 (Armoured) 3 

Kaba Thorlock 4 Integral lock Kaba 20 (Armoured) 3 

Kaba Thorlock 4 Integral lock Kaba 20 (Standard) 3 

Rotalok 60/12/SE Padlock Kaba 20 (Armoured) 3 

Rotalok 60/12/SE Padlock Kaba 20 (Standard) 3 

Rotalok 60/12/ST Padlock Abloy Disklock Pro 

Rotalok 60/12/ST Padlock Abloy Exec 

Rotalok 60/12/ST Padlock Abloy Protec 

Rotalok 60/12/ST-T027 Padlock Assa Twin-Combi 

Rotalok 60/12/ST Padlock Kaba 20 (Armoured) 3 

Rotalok 60/12/ST Padlock Kaba 20 (Standard) 3 

Surelock McGill DL800 Single point surface 

mounted locking 

device with cylinder 

deadlock operated by 

key (outside) and turn 

knob (inside) with 

integrated S-10319 


ASSA Flexicore F523 

 

Surelock McGill DL800 









ASSA 4823 

 










ASSA Twin Combi 

F5823 

 










Abloy Disklok Pro 

CY303 

 

20 Nov 2011 379












Kaba QS152.100.00 

 










Union 2X20A 

 

Notes 

1. Certification does not cover the use of locks other than those listed above. Utilisation of unlisted locks may 

affect the level of security offered by the door set. 

2. The ‘user friendliness’ of employing the padlocks listed above has not been assessed as this is beyond 

the scope of LPS 1175: Issue 5. 

3. The torque resistant version of the Kaba 20 cylinder must be fitted to these padlocks in place of the standard 

Kaba 20 cylinders. 

4. Certification only covers the galvanised mild steel versions. 

Certificate No: 450f to LPS 1175: Issue 7 


Product Name Doorset Configuration Minimum 

Structural 

Opening 

Height (m) 

Sentinel UltraSecure Single leaf outward 



Double 1 leaf outward 



























Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Cert. No. 

1.8 2.35 0.75 1.2 3 450f/01 

1.8 2.35 1.2 2.185 3 2 450f/02 

1.8 2.35 0.75 1.2 4 450f/03 

1.8 2.35 1.2 2.185 4 450f/04 

1.8 2.35 0.75 1.2 5 450f/05 

1.8 2.35 1.2 2.3 5 450f/06 

1.7 2.35 0.75 1.2 3 450f/07 

1.7 2.35 1.2 2.35 3 2 450f/08 

1.7 2.35 0.75 1.2 4 450f/09 

1.7 2.35 1.2 2.35 4 450f/10 

380 20 Nov 2011




LPCB Ref. Trade Name Type Compatible Locking Systems 

No. 

450f/01 Sentinel 

UltraSecure 



SM1 to SM5, SM11 to SM15 and SM21 to 

SM25 


UltraSecure 



SM1 to SM5, SM11 to SM15 and SM21 to 

SM25 


UltraSecure 



SM6 to SM10, SM16 to SM20 and SM26 

to SM30 


UltraSecure 



SM6 to SM10, SM16 to SM20 and SM26 

to SM30 


UltraSecure 



MT21 to MT30, MT51 to MT60 and MT81 

to MT90 


UltraSecure 

Double1 leaf outward opening 


MT22, MT24, MT26, MT28, MT30, MT52, 

MT54, MT56, MT58, MT60, MT82, MT84, 

MT86, MT88, MT90 


UltraSecure 



MT1 to MT10, MT31 to MT40 and MT61 to 

MT70 


UltraSecure 



MT1(T) to MT10(T), MT31(T) to MT40(T) 

and MT61(T) to MT70(T) 


UltraSecure 



MT11 to MT20, MT41 to MT50 and MT71 

to MT80 


UltraSecure 




MT12(T), MT14(T), MT16(T), MT18(T), 

MT20(T), MT42(T), MT44(T), MT46(T), 

MT48(T), MT50(T), MT72(T), MT74(T), 

MT76(T), MT78(T), MT80(T) 

Compatible 

Locking System 

SM1 

SM2 

SM3 

SM4 

Manufacturer Operating Devices Compatible 

Active Leaf 

Passive Leaf Cylinders 

Surelock McGill 

Limited 


Limited 


Limited 


Limited 

Model External Face Internal Face 

EX800-K2-Q4-P- 

(04/05) single 

point emergency 

exit device 

DL800-Q4-P- 


point lock 

SL315-H3-P-A5- 

(04/05) three point 


device 

SL314-P-A5- 


panic exit device 

Key and lever 

handle 

Key and lever 

handle 

Key and lever 

handle 

Key and lever 

handle 

Single action 

lever handle 


lever handle 

Single action 

push pad 

Panic bar 

Two S3TB barrel 

bolts 


bolts 


bolts 


bolts 

AH, AM, AN, 

AO, AP 

AH, AM, AN, 

AO, AP 

AH, AM, AN, 

AO, AP 

AH, AM, AN, 

AO, AP 

SM5 


Limited 

AC800-K2-K4-P-R- 


point lock 3 

Electromechanical 


lock (fail secure) 

with key override 




lock with break 

dome thumb turn 

override and 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM6 


Limited 

SL315-P5-A5- 



device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

20 Nov 2011 381



SM7 


Limited 

SL313-P5-A5-K15- 



Key and lever 

handle 


lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM8 

SM9 


Limited 


Limited 

SL315-H3-P5-A5- 



device 

SL314-P5-A5- 



Key and lever 

handle 

Key and lever 

handle 

Single action 

push pad 

Panic bar 


bolts 


bolts 

AH, AM, AN, 

AO, AP 

AH, AM, AN, 

AO, AP 

SM10 


Limited 

SL322-P5-A5-K2- 

K4-(04/05) three 

point locking 

system 3 










override and 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM11 


Limited 

AC800-K2-P-Q4-R- 

X-(04/05) single 


exit device 3 






Single action 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM12 


Limited 

AC800-K2-K9-P- 

Q4-R-(04/05) 

single point lock 3 







lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM13 


Limited 

SL325-H3-P-K2- 

A5-R-(04/05) three 


exit device 3 






Single action 

push pad 


bolts 

AH, AM, AN, 

AO, AP 

SM14 


Limited 

SL324-P-A5-K2-R- 


panic exit device 3 






Panic bar 


bolts 

AH, AM, AN, 

AO, AP 

SM15 


Limited 

AC800-K2-K4-P-R- 


point lock 3 










override and 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

382 20 Nov 2011



SM16 


Limited 

SL325-P5-K2-A5- 

R-(04/05) three 


exit device 3 






Single action 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM17 


Limited 

SL323-P5-K2-K15- 

A5-R-(04/05) three 

point locking 

system 3 







lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM18 


Limited 

SL325-H3-P5-K2- 

A5-R-(04/05) three 


exit device 3 






Single action 

push pad 


bolts 

AH, AM, AN, 

AO, AP 

SM19 


Limited 

SL324-P5-A5-K2- 

R-(04/05) three 

point panic exit 

device 3 






Panic bar 


bolts 

AH, AM, AN, 

AO, AP 

SM20 


Limited 

SL322-P5-A5-K2- 

K4-(04/05) three 

point locking 

system 3 










override and 

lever handle 


bolts 

AH, AM, AN, 

AO, AP 

SM21 


Limited 

EX800-Q4-(04/05) 

single point 


device 

None 

Single action 

lever handle 


bolts 


SM22 


Limited 

DL800-Q4-(04/05) 


None 


lever handle 


bolts 


SM23 

SM24 


Limited 


Limited 

SL315-H3-A5- 



device 

SL314-A5-(04/05) 

three point panic 

exit device 

None 

Single action 

push pad 


bolts 

None Panic bar Two S3TB barrel 

bolts 



20 Nov 2011 383



SM25 


Limited 

AC800-K4-R- 


point lock 3 None Electromechanical 



with break dome 

thumb turn 

override and 

lever handle 


bolts 


SM26 

SM27 


Limited 


Limited 

SL315-A5-(04/05) 

three point 


device 

SL313-O0-A5-K15- 



None 

None 

Single action 

lever handle 


lever handle 


bolts 


bolts 



SM28 

SM29 


Limited 


Limited 

SL315-H3-A5- 



device 

SL314-A5-(04/05) 


exit device 

None 

Single action 

push pad 


bolts 

None Panic bar Two S3TB barrel 

bolts 



SM30 


Limited 

SL322-A5-K4- 


locking system 3 None Electromechanical 



with break dome 

thumb turn 

override and 

lever handle 


bolts 


MT1 

Tindall 

Engineering 

Limited 

Abryll AD 4 SATE 

USCH3 single 


exit device 

Key and lever 

handle 

Single action 

lever handle 


A to M and AH 

to AN 

MT1 

Tindall 

Engineering 

Limited 


EPC USCH3 

single point 


device 

Key and lever 

handle 

Single action 

lever handle 

Not applicable N, Q, T, V, X, Z, 

AB, AD, AF 

MT1(T) 

Tindall 

Engineering 

Limited 


USCH3 single 


exit device 

Key and lever 

handle 

Single action 

lever handle 

Two HSTB barrel 

bolts 

A to M and AH 

to AN 

384 20 Nov 2011



MT1(T) 

Tindall 

Engineering 

Limited 


EPC USCH3 

single point 


device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT2 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE 

USCH3three point 


device 

Key and lever 

handle 

Single action 

lever handle 


A to M and AH 

to AN 

MT2 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE EPC 

USCH3 three point 


device 

Key and lever 

handle 

Single action 

lever handle 


AB, AD, AF 

MT2(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE USCH3 

three point 


device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

A to M and AH 

to AN 

MT2(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT3 

Tindall 

Engineering 

Limited 

Abryll AD 3 

USCH3 single 

point lock 

Key and lever 

handle 


lever handle 


A to M and AH 

to AN 

MT3 

Tindall 

Engineering 

Limited 

Abryll AD 3 EPC 

USCH3 single 

point lock 

Key and lever 

handle 


lever handle 

Not applicable O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT3(T) 

Tindall 

Engineering 

Limited 

Abryll AD 3 

USCH3 single 

point lock 

Key and lever 

handle 


lever handle 


bolts 

A to M and AH 

to AN 

MT3(T) 

Tindall 

Engineering 

Limited 

Abryll AD 3 EPC 

USCH3 single 

point lock 

Key and lever 

handle 


lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT4 

Tindall 

Engineering 

Limited 

942-3L INT AD 



Key and lever 

handle 


lever handle 


A to M and AH 

to AN 

MT4 

Tindall 

Engineering 

Limited 

942-3L INT AD 

EPC USCH3 three 

point locking 

system 

Key and lever 

handle 


lever handle 


W, Y, AA, AC, 

AE, AG 

MT4(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 



Key and lever 

handle 


lever handle 


bolts 

A to M and AH 

to AN 

20 Nov 2011 385



MT4(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 


point locking 

system 

Key and lever 

handle 


lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT5 

Tindall 

Engineering 

Limited 


USCH3 single 


exit device 

Key and lever 

handle 

Single action 

push pad 


A to M and AH 

to AN 

MT5 

Tindall 

Engineering 

Limited 


EPC USCH3 

single point 


device 

Key and lever 

handle 

Single action 

push pad 


AB, AD, AF 

MT5(T) 

Tindall 

Engineering 

Limited 


USCH3 single 


exit device 

Key and lever 

handle 

Single action 

push pad 


bolts 

A to M And AH 

to AN 

MT5(T) 

Tindall 

Engineering 

Limited 


EPC USCH3 

single point 


device 

Key and lever 

handle 

Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT6 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE USCH3 

three point 


Key and lever 

handle 

Single action 

push pad 


A to M and AH 

to AN 

device 

MT6 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

push pad 


AB, AD, AF 

MT6(T) 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE 



Key and lever 

handle 

Single action 

push pad 


bolts 

A to M and AH 

to AN 

device 

MT6(T) 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT7 

Tindall 

Engineering 

Limited 


USCH3 single 


device 

Key and lever 

handle 

Panic bar Not applicable A to M and AH 

to AN 

MT7 

Tindall 

Engineering 

Limited 


EPC USCH3 

single point panic 

exit device 

Key and lever 

handle 

Panic bar Not applicable N, Q, T, V, X, Z, 

AB, AD, AF 

MT7(T) 

Tindall 

Engineering 

Limited 


USCH3 single 


device 

Key and lever 

handle 

Panic bar 


bolts 

A to M and AH 

to AN 

386 20 Nov 2011



MT7(T) 

Tindall 

Engineering 

Limited 


EPC USCH3 


exit device 

Key and lever 

handle 

Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT8 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE USCH3 


Key and lever 

handle 


to AN 

exit device 

MT8 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE EPC 



Key and lever 

handle 


AB, AD, AF 

MT8(T) 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE USCH3 


Key and lever 

handle 

Panic bar 


bolts 

A to M and AH 

to AN 

exit device 

MT8(T) 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE EPC 



Key and lever 

handle 

Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT9 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH3 single 

point lock 3 

Key and lever 

handle 



lock with 

shrouded thumb 


lever handle 


A to M and AH 

to AN 

MT9 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) EPC 

USCH3 single 

point lock 3 

Key and lever 

handle 



lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT9(T) 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH3 single 

point lock 3 

Key and lever 

handle 



lock with 



lever handle 


bolts 

A to M and AH 

to AN 

MT9(T) 

Tindall 

Engineering 

Limited 

Abryll EM 1 


USCH3 single 

point lock 3 

Key and lever 

handle 



lock with 



lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

20 Nov 2011 387



MT10 

Tindall 

Engineering 

Limited 

942-3L EM (fail 

secure) USCH3 

three point locking 

system 3 

Key and lever 

handle 



lock with 



lever handle 


A to M and AH 

to AN 

MT10 

Tindall 

Engineering 

Limited 


secure) EPC 


locking system 3 

Key and lever 

handle 



lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT10(T) 

Tindall 

Engineering 

Limited 


secure) USCH3 


system 3 

Key and lever 

handle 



lock with 



lever handle 


bolts 

A to M and AH 

to AN 

MT10(T) 

Tindall 

Engineering 

Limited 


secure) EPC 



Key and lever 

handle 



lock with 



lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT11 

Tindall 

Engineering 

Limited 


USCH4 single 


exit device 

Key and lever 

handle 

Single action 

lever handle 


B to M and AH 

to AN 

MT11 

Tindall 

Engineering 

Limited 


EPC USCH4 

single point 


device 

Key and lever 

handle 

Single action 

lever handle 


AB, AD, AF 

MT12 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE USCH4 

three point 


device 

Key and lever 

handle 

Single action 

lever handle 


B to M and AH 

to AN 

MT12 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

lever handle 


AB, AD, AF 

MT12(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE USCH4 

three point 


device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

B to M and AH 

to AN 

388 20 Nov 2011



MT12(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT13 

Tindall 

Engineering 

Limited 


USCH4 single 

point lock 

Key and lever 

handle 


lever handle 


B to M and AH 

to AN 

MT13 

Tindall 

Engineering 

Limited 


EPC USCH4 


Key and lever 

handle 


lever handle 


W, Y, AA, AC, 

AE, AG 

MT14 

Tindall 

Engineering 

Limited 

942-3L INT AD 



Key and lever 

handle 


lever handle 


B to M and AH 

to AN 

MT14 

Tindall 

Engineering 

Limited 

942-3L INT AD 


point locking 

system 

Key and lever 

handle 


lever handle 


W, Y, AA, AC, 

AE, AG 

MT14(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 



Key and lever 

handle 


lever handle 


bolts 

B to M and AH 

to AN 

MT14(T) 

Tindall 

Engineering 

Limited 

942-3L INT AD 


point locking 

system 

Key and lever 

handle 


lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT15 

Tindall 

Engineering 

Limited 


USCH4 single 


exit device 

Key and lever 

handle 

Single action 

push pad 


B to M and AH 

to AN 

MT15 

Tindall 

Engineering 

Limited 


EPC USCH4 

single point 


device 

Key and lever 

handle 

Single action 

push pad 


AB, AD, AF 

MT16 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE USCH4 

three point 


device 

Key and lever 

handle 

Single action 

push pad 


B to M and AH 

to AN 

MT16 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

push pad 


AB, AD, AF 

MT16(T) 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE USCH4 

three point 


device 

Key and lever 

handle 

Single action 

push pad 


bolts 

B to M and AH 

to AN 

20 Nov 2011 389



MT16(T) 

Tindall 

Engineering 

Limited 

942-3P INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT17 

Tindall 

Engineering 

Limited 


USCH4 single 


device 

Key and lever 

handle 

Panic bar Not applicable B to M and AH 

to AN 

MT17 

Tindall 

Engineering 

Limited 


EPC USCH4 


exit device 

Key and lever 

handle 


AB, AD, AF 

MT18 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE USCH4 


exit device 

Key and lever 

handle 


to AN 

MT18 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE EPC 



Key and lever 

handle 


AB, AD, AF 

MT18(T) 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE USCH4 


exit device 

Key and lever 

handle 

Panic bar 


bolts 

B to M and AH 

to AN 

MT18(T) 

Tindall 

Engineering 

Limited 

942-3 INT AD 

SATE EPC 



Key and lever 

handle 

Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT19 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH4 single 

point lock 3 

Key and lever 

handle 



lock with 



lever handle 


B to M and AH 

to AN 

MT19 

Tindall 

Engineering 

Limited 

Abryll EM 1 


USCH4 single 

point lock 3 

Key and lever 

handle 



lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

390 20 Nov 2011



MT20 

Tindall 

Engineering 

Limited 


secure) USCH4 


system 3 

Key and lever 

handle 



lock with 



lever handle 


B to M and AH 

to AN 

MT20 

Tindall 

Engineering 

Limited 


secure) EPC 



Key and lever 

handle 



lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT20(T) 

Tindall 

Engineering 

Limited 


secure) USCH4 


system 3 

Key and lever 

handle 



lock with 



lever handle 


bolts 

B to M and AH 

to AN 

MT20(T) 

Tindall 

Engineering 

Limited 


secure) EPC 



Key and lever 

handle 



lock with 



lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT21 

MT21 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Abryll AD3 SATE 

USCH5 single 


exit device 


EPC USCH5 

single point 


device 

Key and lever 

handle 

Key and lever 

handle 

Single action 

lever handle 

Single action 

lever handle 


B to M and AH 

to AN 


AB, AD, AF 

MT22 

Tindall 

Engineering 

Limited 

942L INT AD 

SATE USCH5 

three point 


device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

B to M and AH 

to AN 

MT22 

Tindall 

Engineering 

Limited 

942L INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT23 

Tindall 

Engineering 

Limited 

Abryll AD3 USCH5 


Key and lever 

handle 


lever handle 


B to M and AH 

to AN 

20 Nov 2011 391



MT23 

MT24 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Abryll AD3 EPC 

USCH5 single 

point lock 

942L INT AD 



Key and lever 

handle 

Key and lever 

handle 


lever handle 


lever handle 


W, Y, AA, AC, 

AE, AG 


bolts 

B to M and AH 

to AN 

MT24 

Tindall 

Engineering 

Limited 

942L INT AD EPC 



Key and lever 

handle 


lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT25 

Tindall 

Engineering 

Limited 


USCH5 single 


exit device 

Key and lever 

handle 

Single action 

push pad 


B to M and AH 

to AN 

MT25 

Tindall 

Engineering 

Limited 


EPC USCH5 

single point 


device 

Key and lever 

handle 

Single action 

push pad 


AB, AD, AF 

MT26 

Tindall 

Engineering 

Limited 

942P INT AD 

SATE USCH5 

three point 


device 

Key and lever 

handle 

Single action 

push pad 


bolts 

B to M and AH 

to AN 

MT26 

Tindall 

Engineering 

Limited 

942P INT AD 

SATE EPC 



device 

Key and lever 

handle 

Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT27 

Tindall 

Engineering 

Limited 


USCH5 single 


device 

Key and lever 

handle 


to AN 

MT27 

Tindall 

Engineering 

Limited 


EPC USCH5 


exit device 

Key and lever 

handle 


AB, AD, AF 

MT28 

Tindall 

Engineering 

Limited 

942 INT AD SATE 



Key and lever 

handle 

Panic bar 


bolts 

B to M and AH 

to AN 

MT28 

Tindall 

Engineering 

Limited 

942 INT AD SATE 



device 

Key and lever 

handle 

Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT29 

Tindall 

Engineering 

Limited 

Abryll EM3 

(fail secure) 

USCH5 single 

point lock 3 








lock with thumb 


lever handle 


B to M and AH 

to AN 

392 20 Nov 2011



MT29 

Tindall 

Engineering 

Limited 

Abryll EM3 


USCH5 single 

point lock 3 










lever handle 


W, Y, AA, AC, 

AE, AG 

MT30 

Tindall 

Engineering 

Limited 

942L EM 

(fail secure) 












lever handle 


bolts 

B to M and AH 

to AN 

MT30 

Tindall 

Engineering 

Limited 

942L EM 













lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT31 

Tindall 

Engineering 

Limited 

Abryll EM 4 SATE 

(fail secure) 

USCH3 single 


exit device 3 






Single action 

lever handle 


A to M and AH 

to AN 

MT31 

Tindall 

Engineering 

Limited 



USCH3 single 


exit device 3 






Single action 

lever handle 


AB, AD, AF 

MT31(T) 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 


exit device 3 






Single action 

lever handle 


bolts 

A to M and AH 

to AN 

20 Nov 2011 393



MT31(T) 

Tindall 

Engineering 

Limited 



USCH3 single 


exit device 3 






Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT32 

Tindall 

Engineering 

Limited 

942-3L EM SATE 

(fail secure) 



device 3 






Single action 

lever handle 


A to M and AH 

to AN 

MT32 

Tindall 

Engineering 

Limited 





device 3 






Single action 

lever handle 


AB, AD, AF 

MT32(T) 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

lever handle 


bolts 

A to M and AH 

to AN 

MT32(T) 

Tindall 

Engineering 

Limited 





device 3 






Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT33 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 

point lock 3 







lever handle 


A to M and AH 

to AN 

394 20 Nov 2011



MT33 

Tindall 

Engineering 

Limited 



USCH3 single 

point lock 3 







lever handle 


W, Y, AA, AC, 

AE, AG 

MT33(T) 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 

point lock 3 







lever handle 


bolts 

A to M and AH 

to AN 

MT33(T) 

Tindall 

Engineering 

Limited 



USCH3 single 

point lock 3 







lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT34 

Tindall 

Engineering 

Limited 

942-3L EM 

(fail secure) 









lever handle 


A to M and AH 

to AN 

MT34 

Tindall 

Engineering 

Limited 

942-3L EM 










lever handle 


W, Y, AA, AC, 

AE, AG 

MT34(T) 

Tindall 

Engineering 

Limited 

942-3L EM 

(fail secure) 









lever handle 


bolts 

A to M and AH 

to AN 

20 Nov 2011 395



MT34(T) 

Tindall 

Engineering 

Limited 

942-3L EM 










lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT35 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 


exit device 3 






Single action 

push pad 


A to M and AH 

to AN 

MT35 

Tindall 

Engineering 

Limited 



USCH3 single 


exit device 3 






Single action 

push pad 


AB, AD, AF 

MT35(T) 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 


exit device 3 






Single action 

push pad 


bolts 

A to M and AH 

to AN 

MT35(T) 

Tindall 

Engineering 

Limited 



USCH3 single 


exit device 3 






Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT36 

Tindall 

Engineering 

Limited 

942-3P EM SATE 

(fail secure) 



device 3 






Single action 

push pad 


A to M and AH 

to AN 

396 20 Nov 2011



MT36 

Tindall 

Engineering 

Limited 





device 3 






Single action 

push pad 


AB, AD, AF 

MT36(T) 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

push pad 


bolts 

A to M and AH 

to AN 

MT36(T) 

Tindall 

Engineering 

Limited 





device 3 






Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT37 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 


device 3 







to AN 

MT37 

Tindall 

Engineering 

Limited 



USCH3 single 


device 3 







AB, AD, AF 

MT37(T) 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH3 single 


device 3 






Panic bar 


bolts 

A to M and AH 

to AN 

20 Nov 2011 397



MT37(T) 

Tindall 

Engineering 

Limited 



USCH3 single 


device 3 






Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT38 

Tindall 

Engineering 

Limited 

942-3 EM SATE 

(fail secure) 









to AN 

MT38 

Tindall 

Engineering 

Limited 

942-3 EM SATE 










AB, AD, AF 

MT38(T) 

Tindall 

Engineering 

Limited 

942-3 EM SATE 

(fail secure) 








Panic bar 


bolts 

A to M and AH 

to AN 

MT38(T) 

Tindall 

Engineering 

Limited 

942-3 EM SATE 









Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT39 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH3 single 

point lock 3 








lock with 



lever handle 


A to M and AH 

to AN 

398 20 Nov 2011



MT39 

Tindall 

Engineering 

Limited 

Abryll EM 1 


USCH3 single 

point lock 3 








lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT39(T) 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH3 single 

point lock 3 








lock with 



lever handle 


bolts 

A to M and AH 

to AN 

MT39(T) 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure)EPC 

USCH3 single 

point lock 3 








lock with 



lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT40 

Tindall 

Engineering 

Limited 


secure) USCH3 


system 3 








lock with 



lever handle 


A to M and AH 

to AN 

MT40 

Tindall 

Engineering 

Limited 


secure) EPC 










lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT40(T) 

Tindall 

Engineering 

Limited 


secure) USCH3 


system 3 








lock with 



lever handle 


bolts 

A to M and AH 

to AN 

20 Nov 2011 399



MT40(T) 

Tindall 

Engineering 

Limited 


secure) EPC 










lock with 



lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT41 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH4 single 


exit device 3 






Single action 

lever handle 


B to M and AH 

to AN 

MT41 

Tindall 

Engineering 

Limited 



USCH4 single 


exit device 3 






Single action 

lever handle 


AB, AD, AF 

MT42 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

lever handle 


B to M and AH 

to AN 

MT42 

Tindall 

Engineering 

Limited 





device 3 






Single action 

lever handle 


AB, AD, AF 

MT42(T) 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

lever handle 


bolts 

B to M and AH 

to AN 

400 20 Nov 2011



MT42(T) 

Tindall 

Engineering 

Limited 





device 3 






Single action 

lever handle 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT43 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH4 single 

point lock 3 







lever handle 


B to M and AH 

to AN 

MT43 

Tindall 

Engineering 

Limited 



USCH4 single 

point lock 3 







lever handle 


W, Y, AA, AC, 

AE, AG 

MT44 

Tindall 

Engineering 

Limited 

942-3L EM 

(fail secure) 









lever handle 


B to M and AH 

to AN 

MT44 

Tindall 

Engineering 

Limited 

942-3L EM 










lever handle 


W, Y, AA, AC, 

AE, AG 

MT44(T) 

Tindall 

Engineering 

Limited 


(fail secure) 









lever handle 


bolts 

B to M and AH 

to AN 

20 Nov 2011 401



MT44(T) 

Tindall 

Engineering 

Limited 











lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT45 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH4 single 


exit device 3 






Single action 

push pad 


B to M and AH 

to AN 

MT45 

Tindall 

Engineering 

Limited 



USCH4 single 


exit device 3 






Single action 

push pad 


AB, AD, AF 

MT46 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

push pad 


B to M and AH 

to AN 

MT46 

Tindall 

Engineering 

Limited 





device 3 






Single action 

push pad 


AB, AD, AF 

MT46(T) 

Tindall 

Engineering 

Limited 


(fail secure) 



device 3 






Single action 

push pad 


bolts 

B to M and AH 

to AN 

402 20 Nov 2011



MT46(T) 

Tindall 

Engineering 

Limited 





device 3 






Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT47 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH4 single 


device 3 







to AN 

MT47 

Tindall 

Engineering 

Limited 



USCH4 single 


device 3 







AB, AD, AF 

MT48 

Tindall 

Engineering 

Limited 

942-3 EM SATE 

(fail secure) 









to AN 

MT48 

Tindall 

Engineering 

Limited 

942-3 EM SATE 










AB, AD, AF 

MT48(T) 

Tindall 

Engineering 

Limited 

942-3 EM SATE 

(fail secure) 








Panic bar 


bolts 

B to M and AH 

to AN 

20 Nov 2011 403



MT48(T) 

Tindall 

Engineering 

Limited 

942-3 EM SATE 









Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT49 

Tindall 

Engineering 

Limited 

Abryll EM 1 

(fail secure) 

USCH4 single 

point lock 3 








lock with 



lever handle 


B to M and AH 

to AN 

MT49 

Tindall 

Engineering 

Limited 

Abryll EM 1 


USCH4 single 

point lock 3 








lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT50 

Tindall 

Engineering 

Limited 


secure) USCH4 


system 3 








lock with 



lever handle 


B to M and AH 

to AN 

MT50 

Tindall 

Engineering 

Limited 


secure) EPC 










lock with 



lever handle 


W, Y, AA, AC, 

AE, AG 

MT50(T) 

Tindall 

Engineering 

Limited 


secure) USCH4 


system 3 








lock with 



lever handle 


bolts 

B to M and AH 

to AN 

404 20 Nov 2011



MT53 

Tindall 

Engineering 

Limited 

Abryll EM3 


USCH5 single 

point lock 3 










lever handle 


W, Y, AA, AC, 

AE, AG 

MT54 

Tindall 

Engineering 

Limited 

942L EM 

(fail secure) 












lever handle 


bolts 

B to M and AH 

to AN 

MT54 

Tindall 

Engineering 

Limited 

942L EM 













lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT55 

Tindall 

Engineering 

Limited 

Abryll EM1 SATE 

(fail secure) 

USCH5 single 


exit device 3 






Single action 

push pad 


B to M and AH 

to AN 

MT55 

Tindall 

Engineering 

Limited 



USCH5 single 


exit device 3 






Single action 

push pad 


AB, AD, AF 

MT56 

Tindall 

Engineering 

Limited 

942P EM SATE 

(fail secure) 



device 3 






Single action 

push pad 


bolts 

B to M and AH 

to AN 

20 Nov 2011 405



MT56 

Tindall 

Engineering 

Limited 

942P EM SATE 




device 3 






Single action 

push pad 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT57 

Tindall 

Engineering 

Limited 


(fail secure) 

USCH5 single 


device 3 







to AN 

MT57 

Tindall 

Engineering 

Limited 



USCH5 single 


device 3 







AB, AD, AF 

MT58 

Tindall 

Engineering 

Limited 

942 EM SATE 

(fail secure) 








Panic bar 


bolts 

B to M and AH 

to AN 

MT58 

Tindall 

Engineering 

Limited 

942 EM SATE 









Panic bar 


bolts 

N, Q, T, V, X, Z, 

AB, AD, AF 

MT59 

Tindall 

Engineering 

Limited 

Abryll EM3 

(fail secure) 

USCH5 single 

point lock 3 










lever handle 


B to M and AH 

to AN 

406 20 Nov 2011



MT59 

Tindall 

Engineering 

Limited 

Abryll EM3 


USCH5 single 

point lock 3 










lever handle 


W, Y, AA, AC, 

AE, AG 

MT60 

Tindall 

Engineering 

Limited 

942L EM 

(fail secure) 












lever handle 


bolts 

B to M and AH 

to AN 

MT60 

Tindall 

Engineering 

Limited 

942L EM 













lever handle 


bolts 

O, P, R, S, U, 

W, Y, AA, AC, 

AE, AG 

MT61 

Tindall 

Engineering 

Limited 

Abryll PE 4 SATE 

single point 


device 

None 

Single action 

lever handle 



MT61(T) 

Tindall 

Engineering 

Limited 


single point 


device 

None 

Single action 

lever handle 


bolts 


MT62 

Tindall 

Engineering 

Limited 

942-3L three point 


device 

None 

Single action 

lever handle 



MT62(T) 

MT63 

MT63(T) 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 



device 





None 

None 

None 

Single action 

lever handle 


lever handle 


lever handle 


bolts 



bolts 




MT64 

MT64(T) 

MT65 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

942-3L INT AD 


system 

942-3L INT AD 


system 


single point 


device 

None 

None 

None 


lever handle 


lever handle 

Single action 

push pad 



bolts 





MT65(T) 

Tindall 

Engineering 

Limited 


single point 


device 

None 

Single action 

push pad 


bolts 


MT66 

MT66(T) 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

942-3P three point 


device 



device 

None 

None 

Single action 

push pad 

Single action 

push pad 



bolts 



20 Nov 2011 407



MT67 

MT67(T) 

MT68 

MT68(T) 

MT69 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 



exit device 



exit device 

942-3 three point 




None Panic bar Not applicable Not applicable 

None Panic bar Two HSTB barrel 

bolts 




bolts 

Abryll EM 1 

(fail secure) single 



lock with 



lever handle 




MT69(T) 

Tindall 

Engineering 

Limited 

Abryll EM 1 




lock with 



lever handle 


bolts 


MT70 

Tindall 

Engineering 

Limited 


secure) three point 



lock with 



lever handle 



MT70(T) 

Tindall 

Engineering 

Limited 





lock with 



lever handle 


bolts 


MT71 

Tindall 

Engineering 

Limited 


single point 


device 

None 

Single action 

lever handle 



MT72 

MT72(T) 

MT73 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 



device 



device 



None 

None 

None 

Single action 

lever handle 

Single action 

lever handle 


lever handle 



bolts 





408 20 Nov 2011



MT74 

MT74(T) 

MT75 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

942-3L INT AD 


system 

942-3L INT AD 


system 

Abryll PE 1 single 


exit device 

None 

None 

None 


lever handle 


lever handle 

Single action 

push pad 



bolts 





MT76 

MT76(T) 

MT77 

MT78 

MT78(T) 

MT79 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 



device 



device 

Abryll PE 2 single 


device 





None 

None 

Single action 

push pad 

Single action 

push pad 



bolts 






bolts 

Abryll EM 1 




lock with 



lever handle 




MT80 

Tindall 

Engineering 

Limited 





lock with 



lever handle 



MT80(T) 

Tindall 

Engineering 

Limited 





lock with 



lever handle 


bolts 


MT81 

Tindall 

Engineering 

Limited 

Abryll PE3 single 


exit device 

None 

Single action 

lever handle 



MT82 

MT83 

MT84 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

942L three point 


device 

Abryll AD3 single 

point lock 

942L INT AD three 

point locking 

system 

None 

None 

None 

Single action 

lever handle 


lever handle 


lever handle 


bolts 



bolts 




20 Nov 2011 409



MT85 

MT86 

MT87 

MT88 

MT89 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 

Tindall 

Engineering 

Limited 



exit device 

942P three point 


device 



device 

942 three point 


None 

None 

Single action 

push pad 

Single action 

push pad 



bolts 





bolts 

Abryll EM3 






lever handle 




MT90 

Tindall 

Engineering 

Limited 

942L EM 

(fail secure) three 

point locking 

system 3 None Electromechanical 




lever handle 


bolts 




Reference 

A Abloy Disklock Pro CY201 DP Scandinavian Oval (with tail) 

B Abloy Protec CY201 PT Scandinavian Oval (with tail) 

C Abloy Protec Cliq CY201 Scandinavian Oval (with tail) (Electo-mechanical) 

D AMS CL-OVLD 3 Scandinavian Oval (with tail) (Electo-mechanical) 

E ASSA 4407dp Scandinavian Oval (with tail) 

F ASSA 4407 Cliq Scandinavian Oval (with tail) (Electo-mechanical) 

G ASSA 4807 Scandinavian Oval (with tail) 

H ASSA C5807 Scandinavian Oval (with tail) 

I ASSA Twin 7607 Scandinavian Oval (with tail) 

J Kaba K20 Scandinavian Oval (with tail) 

K Kaba Quattro PluS Scandinavian Oval (with tail) 

L Locken CL-PL2WR 3 Scandinavian Oval (with tail) (Electo-mechanical) 

M Medeco M3-ARX Scandinavian Oval (with tail) 

N Abloy Protec CY304 Europrofile double cylinder (key:key) 

O Abloy Protec Cliq CY333 Europrofile double cylinder (key:thumbturn) (Electomechanical) 

P Abloy Protec CY333 Europrofile double cylinder (key:thumbturn) 

Q Abloy Protec Cliq CY304 Europrofile double cylinder (key:key) (Electo-mechanical) 

R Abloy Protec CY305 Europrofile double cylinder (key:thumbturn) 

S Abloy Protec Cliq CY305 Europrofile double cylinder (key:thumbturn) (Electomechanical) 

410 20 Nov 2011



T ASSA 4422dp Europrofile double cylinder (key:key) 

U ASSA 4427dp Europrofile double cylinder (key:thumbturn) 

V ASSA 44M22 Cliq Europrofile double cylinder (key:key) (Electo-mechanical) 

W ASSA 44M27 Cliq Europrofile double cylinder (key:thumbturn) (Electomechanical) 

X ASSA 4822 Europrofile double cylinder (key:key) 

Y ASSA 4827 Europrofile double cylinder (key:thumbturn) 

Z ASSA C5822 Europrofile double cylinder (key:key) 

AA ASSA C5827 Europrofile double cylinder (key:thumbturn) 

AB ASSA 7622 Europrofile double cylinder (key:key) 

AC ASSA 7627 Europrofile double cylinder (key:thumbturn) 

AD Kaba Quattro PluS Europrofile double cylinder (key:key) 

AE Kaba Quattro PluS Europrofile double cylinder (key:thumbturn) 

AF Medeco M3-ARX Europrofile double cylinder (key:key) 

AG Medeco M3-ARX Europrofile double cylinder (key:thumbturn) 

AH Abloy Protec CY403 Rim 

AI Abloy Protec Cliq CY403 Rim(Electo-mechanical) 

AJ Kaba Quattro Plus Rim 

AK Medeco M3-ARX Rim 

AL AMS CL-CA2D 3 Finish Round (Electo-mechanical) 

AM ASSA 4857 Round threaded 

AN ASSA C5857 Round threaded 

AO Kaba KV06.100 (torque Rim 

resistant) 

AP Yale PK1109 (Pro key) Rim 

Options 

Option 

Upper louver vent (200 mm by 220 

mm) 

Lower louver vent (200 mm by 220 

mm) 


SM1 to SM30, 

MT1 to MT20 and MT1(T) to MT20(T), 

MT31 to MT50 and MT31(T) to MT 50(T), 

MT61 to MT80 and MT61(T) to MT80(T) 

SM1, SM2, SM3, SM5, SM6, SM7, SM8, SM10, SM11, SM12, SM13, SM15, SM16, SM17, SM18, 

SM20, SM21, SM22, SM23, SM25, SM26, SM27, SM28, SM30, MT1, MT1(T), MT2, MT2(T), MT3, 

MT3(T), MT4, MT4(T), MT5, MT5(T), MT6, MT6(T), MT9, MT9(T), MT10, MT10(T), MT11, MT12, 

MT12(T), MT13, MT14, MT14(T), MT15, MT16, MT16(T), MT19, MT20, MT20(T), MT31, MT31(T), 

MT32, MT32(T), MT33, MT33(T), MT34, MT34(T), MT35, MT35(T), MT36, MT36(T), MT39, MT39(T), 

MT40, MT40(T), MT41, MT42, MT42(T), MT43, MT44, MT44(T), MT45, MT46, MT46(T), MT49, MT50, 

MT50(T), MT61, MT61(T), MT62, MT62(T), MT63, MT63(T), MT64, MT64(T), MT65, MT65(T), MT66, 

MT66(T), MT69, MT69(T), MT70, MT70(T), MT71, MT72, MT72(T), MT73, MT74, MT74(T), MT75, 

MT76, MT76(T), MT79, MT80, MT80(T) 

Notes: 

1 

This approval covers double leaf doorsets with: 

 

 

Leafs of equal width (450f/02, 450f/04 and 450f/06); and 

Leafs of unequal width (450f/02 and 450f/04). Both leafs on these doors shall be between 300 mm and 975 mm wide. 

2 If only one barrel bolt on the passive leaf is engaged on configurations SM3, SM4, SM13, SM14, SM23, SM24, MT1(T) to MT10(T), 

MT31(T) to MT40(T) and MT61(T) to MT70(T), these configurations achieve Security Rating 1. Both barrel bolts must therefore be 

engaged to ensure that the doorsets meet the requirements of Security Rating 3. 

3 The resistance of the access control locks and electro-mechanical cylinders to “non-mechanical” attack is not covered by this approval 

as they were outside the scope of LPS 1175. Likewise, the approval does not cover possible effects of any susceptibilities relating to the 

functionality and performance of any access control equipment that may be used to operate these locking systems. This is because the 

scope of access control devices and system configurations that may be used with these locking systems is “infinite”. It is therefore 

recommended that specifiers’ satisfy themselves that the components used are either resistant to mechanical and other forms of 



20 Nov 2011 411


HIGH SECURITY HINGED DOORSETS WITH GLAZED LEAVES 

Blyweert Beaufort Aluminium Limited 

Imperial Park, Celtic Way, Newport NP10 8BE, United Kingdom 

Tel: +44 (0)1633 294040 • Fax: +44 (0)1633 294041 

E-mail: sales@blyweertbeaufort.com • Website: www.blyweertbeaufort.com 


Hinged Security Doorset 

Product 

Type 

Name 

'LPS 1175 Single leaf bidirectional 

Commercial glazed aluminium doorset with 

Door' anti-finger trap hinges and two 

deadlocks on the leading 

edge 

Minimum Maximum Minimum Maximum Security Cert. 

Height (m) Height (m) Width (m) Width (m) Rating No. 

1.8 2.2 0.9 1.2 2 1 975a/01 

Compatible Locking System 

Manufacturer Model Type Compatible Cylinders 

Adams Rite Sentinel 6 Deadlock fitted w ith the Adams 

Rite Sentinel security 

escutcheon and lock face plate 


Adams Rite 

CL1-ED3535-SC-KD Double europrofile 


Compatible Glazing Material 


Hamilton Erskine TECDUR SR2/SR3 DGU 28 mm thick double glazing unit 

Notes: 

1. The doorset achieves Security Rating 2 in the optimum locked condition, i.e. when both locks are engaged. A Security Rating 1 

classification is achieved when only one lock is engaged. 

2. The quality of work conducted by those fabricating and installing the doorset can affect the products’ ability to offer resistance to 

forced entry commensurate with that of the Security Rating attributed to the doorset. It is therefore recommended that the doorset is 

sourced from fabricators that hold LPCB approval for the fabrication of this doorset. 



Tel: +44 (0)1724 271999 • Fax: +44 (0)1724 271888 




Product 

Name 

Product 

Type 

Minimum 

Structural 


(m) 

M2M3 

Combat 

Single leaf 

outward 

opening 

doorset 

Double leaf 

outward 

opening 

doorset 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.745 2.43 0.74 1.18 3 312e/01 

1.745 2.43 1.15 2.20 3 312e/02 

412 20 Nov 2011



Product 

Name 

M2M3 

Substation 

Product 

Type 

Single leaf 

outward 

opening 

doorset 

Double leaf 

outward 

opening 

doorset 

Minimum 

Structural 


(m) 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.745 2.43 0.74 1.18 3 312e/03 

1.745 2.43 1.15 2.20 3 312e/04 

Note 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the sizes, locking devices and accessories approved on the M2M3 doorset 

ranges. 

C W Fields and Son Limited 

Station Road Industrial Estate, Epworth, Nr. Doncaster, South Yorkshire DN9 1JZ, United Kingdom 

Tel: +44 (0)1427 872368 • Fax: +44 (0)1427 873057 

E-mail: info@cwfields.co.uk • Website: www.cwfields.co.uk 



Product 

Name 

Type 

Security 

Rating 

Cert. 

No. 

Fields Security Single leaf outward opening hinged security doorset 2 940a/01 

Single leaf outward opening hinged security doorset with fixed/removable over 

2 940a/02 

panels 

Single leaf inward opening hinged security doorset 2 940a/03 

Single leaf inward opening hinged security doorset with fixed/removable over panels 2 940a/04 

Double leaf outward opening hinged security doorset 2 940a/05 

Double leaf outward opening hinged security doorset with fixed/removable over 

2 940a/06 

panels 

Double leaf inward opening hinged security doorset 2 940a/07 

Double leaf inward opening hinged security doorset with fixed/removable over 

panels 

2 940a/08 

Note: 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the sizes, locking systems and accessories approved on the Fields Security 

doorset range. 



Tel: +44 (0)1685 350114 • Fax: +44 (0)1685 723276 




Product 

Name 

Type 

Minimum 

Structural 


(m) 

Desray Single leaf 

outward 



Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 


20 Nov 2011 413



Product 

Name 

Type 

Double leaf 

outward 



Minimum 

Structural 


(m) 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 


Note 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the locking systems and accessories approved on the Desray doorsets. 



Tel: +44 (0)191 438 3222 • Fax: +44 (0)191 438 1686 




Product 

Type 

Name 

SecureLine 



Single leaf inward opening hinged 

security doorsets 



Double leaf inward opening 


Minimum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

2.0 2.6 0.85 1.4 2 712b/01 

2.0 2.6 0.85 1.4 2 

2.0 2.6 1.5 2.8 2 

2.0 2.24 1.5 2.8 2 

Compatible Locking Devices and Glazing 

LPCB Product 

Ref. No. Name 

712b/01 SecureLine 

Notes 

Type Lock Cylinder Glazing 2 




Single leaf inw ard 






Double leaf inw ard 



Adams Rite MS2000 maximum 

security deadlock model 2200- 

210 w ith barbolt 



210 w ith barbolt 



250 w ith hookbolt and 

top/bottom rods 



250 w ith hookbolt and 

top/bottom rods 

Assa Sofi 4822 

Europrofile double 











16 mm thick specialist 

laminated glazing unit 







1. The SecureLine doorsets should be mounted within the reveal, directly into the surrounding structure in accordance with Fendor 

Hansen installation instructions SR2+/03. 

2. Alternative glazing may not provide equivalent resistance to attack. Therefore, please consult Fendor Hansen before replacing or 

changing the glazing. 

414 20 Nov 2011





Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 




Product 

Type 

Name 

Liddle Single leaf outward 

Series 3 opening hinged 

doorset 



doorset 

Minimum 

Height (m) 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. 

No. 



Vision Panels 

Note 

Product Name Vision Panels Compatible Doorset Configurations 

Single Leaf Outward Opening Double Leaf Outward Opening 

Liddle Series 3 200 mm wide by 40 mm high 

vision panel 

 

 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the locking systems approved on the Liddle Series 3 doorsets. 

MultiSteel Limited 

MultiSteel House, 117-119 Brent Terrace, London NW2 1LL, United Kingdom 

Tel: +44 (0)20 8208 8300 • Fax: +44 (0)20 8208 8209 

E-mail: office@multisteel.co.uk • Website: www.multisteel.co.uk 



Product 

Name 

Type Minimum 

Height (m) 

Multisteel 

'Mag Lock' 

Multisteel '3 

Point Mul-T- 

Lock' 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Compatible 

Locking 

Systems 

Security 

Rating 

Single leaf 

outward 

opening 

doorset 1, 2 1.83 2.43 0.647 1.377 1 1 818a/01 

Single leaf 1.83 2.43 0.575 1.425 2 2 818a/02 

doorset 1, 2 

outward 

opening 

Cert. 

No. 


20 Nov 2011 415



Locking 

Locking System Operating Devices Compatible 

System Manufacturer Model Type External Face Internal Face Cylinders 

Reference 1 Securitron Magnalock M32 

(top of leaf) and 

M32c (bottom of 

leaf) 

Pair of 

electromagnetic 

locks 

‘Entrotec low rise 

panel with DDA 

features’ access 

control panel with 

PAC panel reader 

(PAC20085) 3 

‘Entrotec DDA 

push to exit’ push 

button release 4 


2 Mul-T-Lock 235 Multipoint mortise 

lock 

Key and lever 

handle 

Key and lever 

handle 

A or B 



A Mul-T-Lock Garrison Double euro-profile cylinder (key:key) 

B Mul-T-Lock Interactive Double euro-profile cylinder (key:key) 

Notes 

1. The doorsets may be used within the walling systems falling within the scope of the ‘Multisteel security screen’ modular 

security screen walling system (LPCB certificate reference 818b/01), for example, to form communal entrance systems. 

2. The doorsets are available with either glazed or opaque panels. 

3. The access control system’s resistance to “non-mechanical” attack has not been assessed as it is outside the scope of 

LPS 1175. It is therefore recommended that specifiers satisfy themselves that the components used are resistant to any 

environmental conditions/interference that may cause the locking system to disengage. 

4. The push button must be located at least 1.5 m from the doorset and any associated side and over panels. 



Tel: +44 (0)1234 826316 • Fax: +44 (0)1234 826319 




Product 

Name 

Sandhurst 

Hendon 

Sandhurst 

Type 









doorset 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

1.9 2.5 0.7 1 3 516a/01 

1.9 2.5 0.7 1 2 516a/02 

1.9 2.5 1.4 2 3 516a/05 

Note 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the locking systems and accessories approved on the Sandhurst and 

Hendon doorsets. 

416 20 Nov 2011





Tel: +44 (0)1233 639039 • Fax: +44 (0)1233 625137 




Product 

Type 

Name 

ExcluDoor 3 

Mk2 

ExecDoor 2 

ExcluDoor 4 

Mk2 

Minimum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 


security doorset with vision panel 

Double leaf, outward opening hinged 


1.8 2.4 1.24 2.4 3 234d/02 

Single leaf, outward opening hinged 1.8 2.2 0.75 1.3 2 234d/03 


Double leaf, outward opening hinged 1.8 2.2 1.5 2.5 2 234d/04 




doorset with vision panel 1.8 2.4 1.24 2.4 4 234d/06 

Cert. 

No. 

Note: 

1. Refer to Volume 2 Part 4 Section 5.1.1 for full details of the locking systems and accessories approved on the ExecDoor 2, ExcluDoor 

3 Mk2 and ExcluDoor 4 Mk2 doorsets. 

20 Nov 2011 417


HIGH SECURITY HINGED DOORSETS WITH OTHER LEAF DESIGNS 



Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 



Hinged Mesh Panel Security Doorsets 


Height (m) 


Single Leaf Mesh 



Double Leaf Mesh 















opening mesh 

panel doorset 

Double leaf 


mesh panel 

doorset 


opening mesh 

panel doorset 

Double leaf 


mesh panel 

doorset 


opening mesh 

panel doorset 

Double leaf 


mesh panel 

doorset 

Maximum Minimum Maximum Security Cert. 

Height (m) Width (m) Width (m) Rating No. 

1.0 2.4 0.6 1.3 1 974a/01 

1.0 2.4 1.2 2.6 1 974a/02 

1.0 2.4 0.6 1.3 2 974a/03 

1.0 2.4 1.2 2.6 2 974a/04 

1.0 2.4 0.6 1.3 3 974a/05 

1.0 2.4 1.2 2.6 3 974a/06 

Compatible Locking Devices 1, 2 01 02 03 04 05 06 

Manufacture Locking Device Type Cylinder Approved Product (LPCB Ref. No. 974a/..) 

Abloy Abloy PL330/25 (V01) HP Padlock Abloy High Profile 

Abloy Abloy PL330/25 (V01) EX Padlock Abloy Exec 

Abloy Abloy PL330/25 (V01) PT Padlock Abloy Protec 



Abloy Abloy PL340/25 (V01) PT Padlock Protec 

Abloy Abloy PL342 (V01) HP Padlock Abloy High Profile 

Abloy Abloy PL342 (V01) EX Padlock Abloy Exec 

Abloy Abloy PL342 (V01) PT Padlock Abloy Protec 



Abloy Abloy PL350/25 (V01) PT Padlock Abloy Protec 

Kaba 

Kaba K18 w ith 11 mm open 

shackle (Item No. K180010-SS) 

Padlock Kaba K20-C5 

Notes: 




3. The Lowrey security mesh doorsets are approved when installed in accordance with the instructions detailed on Lowrey document E- 

INST004 (Issue 4). 

418 20 Nov 2011


HIGH SECURITY HINGED DOORSETS WITH OTHER LEAF DESIGNS 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 


Certificate No: 450j to LPS 1175: Issue 7 

Hinged Mesh Panel Security Doorset 

Product 

Name 


Height (m) 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. 

No. 

Ultrasecure 

SCD1 


opening mesh panel 

1 3 0.5 1.2 3 450j/01 

Ultrasecure 

SCD2 

doorset 


opening mesh panel 

doorset 

1 3 1.2 3 3 450j/02 


Locking Device Type Cylinder Approved Product 

(LPCB Ref. No. 450j/..) 

01 02 

Kaba K18 Padlock Kaba 20 with C5 option 

Notes 

1. Certification does not cover the use of locks other than those listed above. Utilisation of unlisted locks may affect the 

level of security offered by the doorset. 

2. The ‘user friendliness’ of employing the padlock listed above has not been assessed as this is beyond the scope of 

LPS 1175: Issue 7. 

3. The Ultrasecure SCD1 and SCD2 mesh panel doorsets are approved when installed in accordance with the 

instructions detailed on document SCD-DV-3-FIT-01 (Ref.A). 

20 Nov 2011 419


HIGH SECURITY FOLDING DOORSETS 

Bolton Gate Co. Limited 

Waterloo Street, Bolton, Lancashire BL1 2SP, United Kingdom 

Tel: +44 (0)1204 871000 • Fax: +44 (0)1204 871049 

E-mail: kb@boltongate.co.uk • Website: www.boltongate.co.uk 

Certificate No: 026-2b to LPS 1175: Issue 5 

Folding Security Doorsets 

Product Name Type Number 

of Door 

Panels 

Superfold 4000 

Superfold 5000 

Minimum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. No. 

Sliding folding panel 4 3.00 1.70 6.00 4.65 4 026-2b/01 

security door set 1 

Sliding folding panel 6 3.00 2.60 6.00 7.00 4 


Sliding folding panel 

security door set 1 8 3.00 3.55 6.00 8.00 4 

Sliding folding panel 4 3.00 1.70 6.00 4.65 5 026-2b/02 



security door set 


security door set 


LPCB Ref. No. Trade Name 

Locking Device 

026-2b/01 Superfold 4000 Chubb 7009 padbar and Chubb 1K11 padlock 2 

026-2b/02 Superfold 5000 Chubb 7009 padbar and Chubb 1K11 padlock 2 

Notes 

1. Single stack back configuration only. 

2. The locking device is mounted on the "non-attack" face of the doorset. Therefore, although not currently covered by the scope of 

the approval, other padlocks may be suitable for use on the doorsets. 

420 20 Nov 2011


DOMESTIC DOORSETS APPROVED TO PAS 23-1 

Doorsets listed in this section are approved to PAS 23-1 General performance requirements for door 

assemblies - Part 1. Single leaf, external door assemblies to dwellings. 

This standard describes a series of test methods and a range of criteria relevant to the general performance 

of single leaf, single swing, external door assemblies to dwellings. The scope of the standard covers inward 

and outward opening doorsets, with or without integral or coupled side panels and fanlights. Where these are 

covered by the LPCB certificate, details will be provided in the listing for that product. 

The scope of the standard does not cover the installation of the product nor does it cover double leaf doors, 

sliding doors, folding doors, tilt and slide doors, and pivoted doors, or doors with any frame member over 3m. 

For details of hinged doorsets approved to LPS 1175 and PAS 24-1 please refer to sections 5.1 and 5.2.2 

respectively. 



Tel: +44 (0)1795 476161 • Fax: +44 (0)1795 422463 


Certificate No: 322b to PAS23-1: 1999 (Incorporating Amendment No. 1) 


Product Type 

Name 


SD5001 


SD5001(1) 

Single leaf, 


doorsets 

Single leaf, 


doorsets 

Direction of 

Opening 

Minimum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Exposure 

Category 

Cert. 

No. 

Outward 0.951 0.503 3.049 1.332 800U 322b/02 

Inward 0.951 0.503 2.250 1.332 800U 

Compatible Locking Options 

LPCB Ref. 

No. 

Trade Name Type Direction of 

Opening 

322b/02 Martin Roberts 

SD5001 


Single leaf, hinged 



Systems 

Outward 2 

Inward 1 

Option Locking Type 

Compatible External and Internal Operating Devices 

System 

External 

Internal 

1 Assa 1520 Escape Sash Lock Key via an Assa 4801 single 

cylinder or 


cylinder 

Assa 6650C solid brass 

handle plus either 

Assa 6256 thumbturn or 


cylinder 

Note 

2 Assa 8761 Emergency Nightlatch Key via an Assa 4801 single 

cylinder 

Assa 640 solid brass handle 

1. The Martin Roberts SD5001 also meets the requirements of LPS 1175: Issue 5 and PAS 24-1:1999. For further information, please 

refer to entries in sections on LPS 1175: Issue 5 and PAS 24-1 relating to LPCB certificates 322a and 322c respectively. 

20 Nov 2011 421



Salisbury Glass Centre Limited 

Newton Road, Churchfields Industrial Estate, Salisbury, Wiltshire SP2 7QA, United Kingdom 

Tel: +44 (0)1722 342900 • Fax: +44 (0)1722 338784 

E-mail: commercialenquiries@salisbury-glass.com or domesticenquiries@salisbury-glass.com • Website: 

www.salisbury-glass.com 

Certificate No: 947a to PAS 23-1:1999 (incorporating amendments Nos. 1, 2, 3 and 4 and Corrigendum No. 1) and PAS 24:2007 


Product 

Type 

Name 

Visoline 

Fully glazed single 

leaf outward opening 

aluminium doorset 

Minimum 

Structural 


(m) 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Cert. 

No. 

1.85 2.2 0.8 1.05 947a/01 

Notes 

1. This doorset achieves exposure category '850 Special'. 

2. Refer to Volume 2 Part 4 Section 5.2.2 for full details of the locking systems and compatible cylinders approved on the doorsets. 

422 20 Nov 2011

PART 4: SECTION 5.2.2 


Doorsets listed in this section are approved to PAS 24-1 Enhanced security requirements for door assemblies 

- Part 1. Single and double leaf, external door assemblies to dwellings. 

This standard describes a series of test methods and a range of criteria relevant to the general performance 

of single and double leaf, single swing, hinged external door assemblies for dwellings. The scope of the 

standard covers inward and outward opening doorsets, with or without integral or coupled side panels and 

fanlights. Where these are covered by the LPCB certificate, details will be provided in the listing for that 

product. 

The scope of the standard does not cover the installation of the product nor does it cover sliding doors, folding 

doors, tilt and slide doors, and pivoted doors, or doors with any frame member over 3m. 

The concept of ‘enhanced security’ in this product standard is based upon a relationship between forced 

human intervention techniques with basic hand tools and resistance to entry under multi-directional loading 

and hard and soft body impact tests. The standard provides a means of evaluation of resistance to opportunist 

attack. The standard does not provide a means of evaluating the protection provided against unauthorised 

intrusion to the levels of attack or scope of entry methods covered within LPS 1175 Requirements and testing 

procedures for the LPCB approval and listing of intruder resistant building components, strongpoints, security 

enclosures and free-standing barriers. 

The ability to gain entry by picking the locks, deliberately breaking the glass or by attacking the frame fixing 

methods is not addressed in PAS 24-1. 

For details of hinged doorsets approved to LPS 1175 and PAS 23-1 please refer to sections 5.1 and 5.2 

respectively. 



Tel: +44 (0)1795 476161 • Fax: +44 (0)1795 422463 


Certificate No: 322c to PAS24-1: 1999 (Incorporating Amendment No 1) 


Product Name Type Direction of 

Opening 


SD5001 





Minimum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Cert. 

No. 

Outward 0.951 0.503 3.049 1.332 322c/02 

Inward 0.951 0.503 2.250 1.332 

20 Nov 2011 423

PART 4: SECTION 5.2.2 


Compatible Locking Options 

LPCB Ref. Trade Name Type Direction of 

No. 

Opening 

322c/02 Martin Roberts SD5001 Single leaf, hinged security 

doorsets 


Option 

Locking 

System 

Type 

External 

1 Assa 1520 Escape Sash Lock Key via an Assa 4801 single cylinder 

or 

Key via an Assa 4802 double cylinder 


Systems 

Outward 2 

Inward 1 

Compatible External and Internal Operating Devices 

Internal 

Assa 6650C solid brass handle 

plus either 

Assa 6256 thumbturn or 


cylinder 

2 Assa 8761 Emergency Nightlatch Key via an Assa 4801 single cylinder Assa 640 solid brass handle 

Note 

1. The Martin Roberts SD5001 also meets the requirements of LPS 1175: Issue 5 and PAS 23-1: 1999. For further information, please 

refer to entries in sections on LPS 1175: Issue 5 and PAS 23-1 relating to LPCB certificates 322a and 322b respectively. 



Tel: +44 (0)1722 342900 • Fax: +44 (0)1722 338784 



Certificate No: 947a to PAS 23-1:1999 (incorporating amendments Nos. 1, 2, 3 and 4 and Corrigendum No. 1) and PAS 24:2007 


Product 

Type 

Name 

Visoline 

Fully glazed single 

leaf outward opening 

aluminium doorset 

Minimum 

Structural 


(m) 

Maximum 

Structural 


(m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Cert. 

No. 

1.85 2.2 0.8 1.05 947a/01 



Sobinco ACVL 415 Multipoint locking 

system 


Operating Devices 


Key and Hoppe Key and Hoppe 

Tokyo PAS24 Tokyo PAS24 

lever handle set lever handle set 

Compatible 

Cylinders 

A 


A Securistyle Anti-manipulation Double europrofile cylinder (key/key) 

Note 

1. This doorset achieves exposure category '850 Special'. 

424 20 Nov 2011


HIGH SECURITY WINDOWS 

The windows listed in this section are approved to LPS 1175 Requirements and testing procedures for the 

LPCB approval and listing of intruder resistant building components, strongpoints, security enclosures and 

free-standing barriers. 

The windows listed in this section are generally designed for use in commercial applications. Section 5.3.1 

lists external security windows while section 5.3.2 lists secondary glazing systems and section 5.3.3 lists 

rooflights. 

Windows approved to BS 7950 Specification for enhanced security performance of windows for domestic 

applications are listed in section 5.4. 

Unlike BS 7950, LPS 1175 can be applied to all designs and configurations of windows. Windows approved to 

LPS 1175 also generally offer much higher protection against forced entry than windows approved to BS 

7950. This is because windows approved to LPS 1175 are subjected to physical attack tests with a wide 

range of tools aimed at overcoming all aspects of the window including aspects omitted by BS 7950 such as 

the glazing and the fixings used to install the window. 

In addition to approving windows to LPS 1175 and BS 7950, LPCB also offer security performance approval 

of windows and other façade elements to EN 1627 as well as approvals covering other aspects of window 

performance, including weathertightness, thermal performance, fire and acoustics. 

LPCB has also published a standard for glazing and security glazing films which employs the principles 

contained within LPS 1175. LPS 1270 Requirements and testing procedures for the LPCB approval and listing 

of intruder resistant security glazing units covers the resistance to manual attack of the glazing material. It 

enables specifiers to select new or replacement glazing that affords two levels of security equivalent to that of 

the frame or façade in which it is to be employed. 

20 Nov 2011 425


HIGH SECURITY WINDOWS - EXTERNAL WINDOWS 



Tel: +44 (0)191 438 3222 • Fax: +44 (0)191 438 1686 



Security Windows 

Product Name Style Minimum 

Clear 

Opening 

Height 

(m) 

SecureLine 

SR2 

Top hung opening light 

SecureLine 

SR3 

SecureLine 

SR4 

Maximum 

Clear 

Opening 

Height 

(m) 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Width (m) 

Security 

Rating 

Fixed light window 0.96 2.0 0.86 2.0 2 712a/01 

1.0 2.0 0.90 2.0 2 

window 


Top hung opening light 1.0 2.0 0.90 2.0 3 

window 


Cert. 

No. 

Compatible Locking Devices and Glazing 

LPCB 

Ref. No. 

712a/01 

Product 

Name 

SecureLine 

SR2 

Style 

Fixed light 

w indow 

Locking 

N/A 

Glazing 2 

Attack Face Non-attack Face 

8mm thick 32.8mm thick 

specialist laminated specialist laminated 

glazing unit double glazed unit 

Top hung 

opening light 

w indow 

Tw o Wilka dead locks 

w ith key operated 

cylinders 




712a/02 

SecureLine 

SR3 

Fixed light 

w indow 

N/A 




Top hung 

opening light 

w indow 

Tw o Wilka dead locks 

w ith key operated 

cylinders 




712a/03 SecureLine 

SR4 

Fixed light 

w indow 

N/A 

28mm thick 

specialist laninated 

glazing unit 

32.8mm thick 

specialist laminated 

double glazed unit 

Notes 

1. The SecureLine window systems should be mounted within the reveal, directly into the surrounding structure in accordance with 

installation instructions SL-02 (fixed light version) or SL-007 (top hung opening light version). 

2. Alternative glazing may not provide equivalent resistance to attack. Therefore, please consult Fendor Ltd before replacing or 


426 20 Nov 2011


HIGH SECURITY WINDOWS - SECONDARY GLAZING SYSTEMS 


Alban Park, Hatfield Road, St Albans, Hertfordshire AL4 0JJ, United Kingdom 

Tel: +44 (0)1727 837271 • Fax: +44 (0)1727 844053 

E-mail: enquiries@selectaglaze.co.uk • Website: www.selectaglaze.co.uk 


Secondary Security Glazing Systems 

Product Name Type Style Minimum 

Height 

(m) 

Series 50 'Level 

1' 


2' 


1' 


2' 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Single fixed light 

casement 

Single light inward 

opening 

top hung casement 


opening 

side hung casement 

Single fixed light 

casement 


opening 

top hung casement 


opening 

side hung casement 

2H multiple fixed light 

demountable unit 

2V multiple fixed light 




3V multiple fixed light 






Single demountable 

fixed-light unit 


fixed light unit 

2H multi-light 








Maximum 

Height 

(m) 1 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 1 

Security 

Rating 

Cert. 

No. 

0.4 3.2 3 0.4 3.2 3 1 683a/01 

0.43 1.5 3 0.574 3.2 3 1 

0.574 3.2 3 0.43 1.5 3 1 

0.4 3.2 3 0.4 3.2 3 2 683a/02 

0.43 1.5 3 0.574 3.2 3 2 

0.574 3.2 3 0.43 1.5 3 2 

0.4 3.2 3 0.8 4 3 1 683a/03 

0.8 4 3 0.4 3.2 3 1 

0.4 3.2 3 1.2 5 3 1 

1.2 5 3 0.4 3.2 3 1 

0.4 3.2 3 1.6 6 3 1 

0.4 3.2 3 2 6 3 1 

0.4 3.2 3 0.4 3.2 3 1 

0.4 3.2 3 0.4 3.2 3 2 683a/04 

0.4 3.2 3 0.8 4 3 2 

0.4 3.2 3 1.2 5 3 2 

0.4 3.2 3 1.6 6 3 2 

0.4 3.2 3 2 6 3 2 

20 Nov 2011 427



Product Name Type Style Minimum 

Height 

(m) 


3' 


1' 


2' 


1' 


2' 


1' 


2' 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

Secondary 

glazing 

system 

2V multi-light 





fixed light unit 













Twin light horizontally 

sliding casement 

Twin light horizontally 


Twin light vertically 


Twin light vertically 


Maximum 

Height 

(m) 1 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 1 

Security 

Rating 

0.8 4 3 0.4 3.2 3 2 

1.2 5 3 0.4 3.2 3 2 

Cert. 

No. 

0.4 3.2 0.4 3.2 3 683a/06 

0.4 3.2 0.8 4 3 

0.4 3.2 1.2 5 3 

0.4 3.2 1.6 6 3 

0.4 3.2 2 6 3 

0.8 4 0.4 3.2 3 

1.2 5 0.4 3.2 3 

0.65 2.6 7 1 3 7 1 683a/05 

0.65 2.6 7 1 3 7 2 683a/07 

1 3 2, 7 0.65 2.6 2, 7 1 683a/08 

1 3 2, 7 0.65 2.6 2, 7 2 683a/09 

Single fixed light unit 0.3 3 7 0.3 2 7 1 683a/10 

Single fixed light unit 0.3 3 7 0.3 2 7 2 683a/11 

Compatible Locking and Glazing 

LPCB Trade Name Style Locking Systems Glazing 4 

Ref. No. 

683a/01 Series 50 

'Level 1' 

All single fixed light casements None 12.04 mm thick specialist laminated 


All single light inw ard opening Selectaglaze proprietary 12.04 mm thick specialist laminated 

top hung and side hung 

casements 

espagnolette locking system w ith security glass 

Softline LM lockable handle 

683a/02 Series 50 

'Level 2' 

683a/03 Series 55 

'Level 1' 

683a/04 Series 55 

'Level 2' 

All single fixed light casements None 12 mm or 12.4 mm thick specialist 

laminated security glass 

All single light inw ard opening 

top hung and side hung 

casements 

All single and multiple light 

demountable units 



Selectaglaze proprietary 12 mm or 12.4 mm thick specialist 

espagnolette locking system w ith laminated security glass 

Softline LM lockable handle 

None 

12.04 mm thick specialist laminated 


None 

12 mm or 12.4 mm thick specialist 


428 20 Nov 2011



683a/06 Series 55 

'Level 3' 

683a/05 Series 85 

'Level 1' 

683a/07 Series 85 

'Level 2' 

683a/08 Series 95 

'Level 1' 

683a/09 Series 95 

'Level 2' 

683a/10 Series 42 

'Level 1' 

683a/11 Series 42 

'Level 2' 



Tw in light horizontally sliding 

casements 

Tw in light horizontally sliding 

casements 

Tw in light vertically sliding 

casements 

Tw in light vertically sliding 

casements 

None 

Selectaglaze proprietary 

espagnolette locking system 







12 mm thick specialist laminated 










Single fixed light units None 12.04 mm thick specialist laminated 


Single fixed light units None 12 mm or 12.4 mm thick specialist 


Compatible Installation Configurations 

LPCB Ref. 

No. 

Trade Name Com patible Installation Configurations 5 

Masonry Structural Tim ber Timber Stud Structural Steel 

683a/01 Series 50 'Level 1' I and R 6 I and R 6 I and R 6 I and R 6 

683a/02 Series 50 'Level 2' I and R 6 I and R 6 - I and R 6 

683a/03 Series 55 'Level 1' I and R 6 I and R 6 I and R I and R 6 



683a/05 Series 85 'Level 1' I and R I and R I and R I and R 

683a/07 Series 85 'Level 2' I and R I and R - I and R 





Notes: 

1 The maximum size of casements and coupled systems are subject to specific assessment of physical restrictions and operational 

conditions. 

2 The maximum sash area available on Series 95 units is 3.5 m 2 . 

3 The Series 50 and Series 55 'Level 1' and 'Level 2' units can be joined together to form multi-light flat-coupled and bay systems using 

the Selectaglaze standard coupling, direct coupling and timber coupling methods, as appropriate. The security provided is equivalent 

to that offered by the lowest grade unit incorporated in the coupled system. 

4 Alternative glazing may not provide equivalent resistance to attack. Therefore, please consult Selectaglaze before replacing or 


5 This assumes installation direct to substrate as detailed in document DS-003 (Issue AR, 07/049) and not via intermediate substrates, 

such as plasterboard. An 'I' indicates internal face fixed direct to structure while an 'R' indicates reveal mounted direct to structure. 

6 The Series 50 and Series 55 secondary glazing system may be mounted in the reveal (standard, tapered or splayed) or face fixed to 

the inside of the surrounding structure. 

7 The Series 42, 85 and 95 'Level 1' and 'Level 2' units can be joined together to form multi-light flat-coupled and bay systems using the 

Selectaglaze standard coupling and timber coupling methods, as appropriate. The security provided is equivalent to that offered by 

the lowest grade unit incorporated in the coupled system. 

20 Nov 2011 429


ROOFLIGHTS 

The Rooflight Company 

Wychwood Business Centre, Milton Road, Shipton-under-Wychwood, Oxfordshire OX7 6XU, United Kingdom 

Tel: +44 (0)1993 833108 • Fax: +44 (0)1993 831066 

E-mail: info@therooflightcompany.co.uk • Website: www.therooflightcompany.co.uk 


Fixed Rooflights 


Length 

(m) 

Plateau Secured 

by Design: Level 2 

Plateau Secured 

by Design: Level 3 

Maximum 

Length 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Fixed rooflight 0.96 1.76 0.96 2.76 2 929a/01 

Fixed rooflight with 

integral security 

bars 

Cert. 

No. 

0.96 0.96 0.96 2.76 3 929a/02 

Note 

1 Approval is based upon installation of the rooflight onto a reinforced concrete kerb in accordance with drawing 

PS_100INST (Revision B dated 14 August 2009). 

430 20 Nov 2011


DOMESTIC SECURITY WINDOWS 

Windows listed in this section are approved against the requirements of BS 7950 Specification for enhanced 

security performance of windows for domestic applications. 

The scope of windows covered by BS 7950 is restricted to the following: 

(i) 

(ii) 

(iii) 

(iv) 

(v) 

Casement windows - inward and outward opening side hung, outward opening top hung and inward 

opening bottom hung. 

Tilt/turn and turn/tilt windows. 

Fixed lights and dummy vents. 

Top swing. 

Vertical sliding. 

BS 7950 does not assess the resistance to entry by breaking glazing nor does it directly assess the fixing 

method employed. 

The concept of ‘enhanced security’ in this product standard is based upon a relationship between forced 

human intervention techniques with basic hand tools and resistance to entry under multi-directional loading 

and hard and soft body impact tests. The standard provides a means of evaluation of resistance to opportunist 

attack. The standard does not provide a means of evaluating the protection provided against unauthorised 

intrusion to the levels of attack or scope of entry methods covered within LPS 1175 Requirements and testing 



It is recommended that specifiers requiring windows outside the scope of BS 7950 or windows that exhibit 

resistance to methods of forced entry not covered by BS 7950, specify windows that have been approved to 

LPS 1175 (see products listed in section 5.3). Alternatively, specifiers should consider specifying additional 

window protection; such as grilles, shutters or secondary glazing systems; approved to LPS 1175. 

In addition to approving windows to LPS 1175 and BS 7950, LPCB also offer security performance approval 

of windows and other façade elements to EN 1627 as well as approvals covering other aspects of window 

performance, including weathertightness, thermal performance, fire and acoustics. 

LPCB has also published a standard for glazing and security glazing films which employs the principles 

contained within LPS 1175. LPS 1270 Requirements and testing procedures for the LPCB approval and listing 

of intruder resistant security glazing units covers the resistance to manual attack of the glazing material. It 

enables specifiers to select new or replacement glazing that affords two levels of security equivalent to that of 

the frame or façade in which it is to be employed. 

PRO TEC Vinduer A/S 

Nybovej 34, 7500 Holstebro, Denmark 

Tel: +45 9741 3077 • Fax: +45 9741 3060 

E-mail: protec@protecvinduer.com • Website: www.protecvinduer.com 

UK Sales 

PRO TEC Windows Limited, The Plough Barn, Feltmores Park, Chalk Lane, Moor Hall Road, Harlow CM17 

0PF, United Kingdom 

Tel: +44 (0)127 942 4004 • Fax: +44 (0)127 942 1709 

E-mail: protec@protecwindows.com • Website: www.protecwindows.com 

Certificate No: 930a to BS 7950: 1997, BS 6375-1: 2004 and BS 6375-2: 1987 

20 Nov 2011 431



Windows 

Product 

Name 

PRO 

TEC 

Classic 

Type 

Aluminium/timber 

composite single fixed 

light windows 


composite single top 

hung casement 

windows 


composite single side 

hung casement 

windows 


composite single 

terrace side hung 

casement windows 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Compatible 

Locking 

System 

Cert. 

No. 

0.35 3 0.230 3 - 930a/01 

0.353 1.563 0.353 1.563 1 930a/02 

0.363 1.763 0.353 0.953 1 930a/03 

1.713 2.463 0.661 1.063 1 930a/04 

Approval Standards 

LPCB Ref. 

No. 

930a/01 PRO TEC 

Classic 


Classic 


Classic 


Classic 

Trade Name Type BS 7950: 

1997 

Aluminium/timber composite 

single fixed light windows 


single top hung casement 

windows 


single side hung casement 

windows 


single terrace side hung 

casement windows 

BS 6375-1: 

2004 

BS 6375-2: 

1987 

UK 

Exposure 

Category 

1200 

Refer to 

note 1 

1200 

1200 

1200 


Compatible Locking Manufacturer Model Type 

System 

1 Mila A/S Garant D28 Multipoint locking system incorporating four 

locking points and key lockable handle 

Note 

1. Fixed light windows are outside the scope of BS 6375-2: 1987. 



Tel: +44 (0)1722 342900 • Fax: +44 (0)1722 338784 



Certificate No: 947b to BS 7950: 1997, BS 6375-1: 2004, BS 6375-2: 1987 and BS 4873: 2004 

432 20 Nov 2011



Domestic Window 

Product Type 

Name 

Visoline 

Internally glazed 

inward opening 

tilt/turn 

aluminium 

window 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Compatible 

Locking 

Systems 

Cert. 

No. 

0.8 2 0.7 1.2 1 947b/01 

Approval Standards 

LPCB Ref. 

No. 

Trade Name Type BS 7950:1997 BS 6375-1:2004 

(UK Exposure 

Category) 

947b/01 Visoline Internally glazed inw ard opening 

tilt/turn aluminium w indow 


BS 6375-2:1987 BS 4873:2004 

2000+ 

Compatible Manufacturer Model Type 

Locking System 

1 Fappin ACFA 061 Multi point tilt/turn locking system with additional ACFA 078 locking points and ACFA 082 

key locking handle on the internal face. 

Note: 

1. This approval only covers single light units. 

Certificate No: 947c to BS 7950: 1997, BS 6375-1: 2009, BS 6375-2: 2009 and BS 4873: 2009 

Domestic Window 

Product Type 

Name 

Technal 

FXi52 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Compatible 

Locking 

System 

Inward opening 

tilt/turn 

aluminium 

window 1 0.6 2.38 0.6 1.26 1 947c/01 

Cert. 

No. 


Compatible 

Locking 

System 

Manufacturer Model Type Operating Devices 

External Face 

Internal Face 

1 Seigenia SI-line TBT 90 Key locking handle None Key locking 

Seigenia SI-line LM 4200 TBT-E-WK2 Tilt/turn locking system 

handle 

Exposure Category 

Cert. No. Trade Name Type UK Exposure Category 

947c/01 Technal FXi52 Inw ard opening tilt/turn aluminium w indow 2000+ 

Note: 

1. This approval covers single light units. 

20 Nov 2011 433


SECURITY GRILLES, BLINDS AND BARSETS 

Security grilles, blinds and barsets listed in this section are approved to LPS 1175 Requirements and testing 





Tel: +44 (0)1724 271999 • Fax: +44 (0)1724 271888 



Security Grilles 

Product 

Name 

CX2 

Type 

Single gate collapsible 

security grille 

Double gate collapsible 


Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

0.7 3.0 0.4 3.0 1 312a/04 

0.7 3.0 0.4 6.0 1 


LPCB Ref. 

No. 

Bradbury CX250 

two point slam 

lock 

Lock 



lock 



lock 

Cylinders 

312a/04 CX2 single or double 



None. 

Approved Installation Configurations 1 

Configuration 

Substrate 

Brick Concrete Structural 

Steel 

Structural 

Timber 

Reveal 

Internal face fixed 

Note 

1. This assumes installation direct to substrate and not via intermediate substrates, such as plasterboard. 

Henry Lewis and Sons (Wireworkers) Limited 

Unit 7, Bolling Road Industrial Estate, Bradford BD4 7HN, United Kingdom 

Tel: +44 (0) 1274 307359 • Fax: +44 (0) 1274 370784 

E-mail: info@henrylewisandson.co.uk • Website: www.henrylewisandson.co.uk 



Product 

Name 

Balmoral 

Type 

Single gate 

collapsible grille 

Minimum 

Width 

(mm) 

Maximum 

Width 

(mm) 

Minimum 

Height 

(mm) 

Maximum 

Height 

(mm) 

Security 

Rating 

Cert. 

No. 

500 6000 650 3046 1 528a/01 

434 20 Nov 2011



Product 

Name 

Type 

Minimum 

Width 

(mm) 

Maximum 

Width 

(mm) 

Minimum 

Height 

(mm) 

Maximum 

Height 

(mm) 

Security 

Rating 

Double gate 

500 6000 650 3046 1 528a/02 

collapsible grille 

Fixed grille 500 6000 650 3046 1 528a/03 

Cert. 

No. 


Lock Cylinder Approved Product (LPCB Ref. No. 528a/…) 

Adams Rite 

MS1900 


1 2 3 

ASEC AS 1193 single europrofile 

ASEC AS 1153 double europrofile 

Accessory 

Approved Product (LPCB Ref. No. 528a/…) 

1 2 3 

Removable bottom track 

Lift up (hinged) bottom 

track 

 

 


Configuration 

Compatible Substrates 


Steel 

Structural 

Timber 

Reveal 

Internal face 

 

External face 

 

Note 

1. This assumes installation direct to substrate and not via intermediate substrates such as plasterboard. 



Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 



Fixed Security Bar Sets 

Product Type 

Name 

Liddle 

Series 2 

security bar 

set 

Liddle 

Series 3 

security bar 

set 

Reveal mounted 

security bar set 

Internally or 

externally face 

fixed security 

bar set 



Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

Cert. 

No. 

0.4 2.7 0.4 3.0 2 442d/01 

0.1 2.24 0.1 2.54 2 

0.4 2.7 0.4 3.0 3 442d/02 

20 Nov 2011 435



Product 

Name 

Type 

Internally or 

externally face 

fixed security 

bar set 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening Width 

(m) 

Maximum 

Structural 

Opening Width 

(m) 

Security 

Rating 

0.1 2.24 0.1 2.54 3 

Cert. 

No. 

Note 

1. The bar sets are approved when installed directly to brickwork, concrete or steel. The approval does not cover the bar sets when 

mounted to alternative substrates or via intermediate substrates such as plasterboard. 



Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 


Certificate No: 974g to LPS 1175: Issue 7 

Fixed Security Barsets 

Product 

Name 

Product 

Type 

Installation 

Anti- Individual Reveal 

Intruder security mounted 

barset 

Individual 

security 

barset 

Individual 

security 

barset 

Modular 

security 

barset 

Modular 

security 

barset 

Modular 

security 

barset 

External face 

fixed 

Internal face 

fixed 

Reveal 

mounted 

External face 

fixed 

Internal face 

fixed 

Minimum 

Height (m) 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. 

No. 

0.55 2.1 0.55 2.1 3 974g/01 

0.45 2.0 0.45 2.0 3 

0.45 2.0 0.45 2.0 3 

0.55 Unlimited 1 0.55 Unlimited 1 3 



Notes: 

1. The maximum minor dimension approved is 4.1 m. This is because the number of individual barsets that can be connected is 

restricted to a maximum of two in the minor dimension. However, the barset’s size is unrestricted in the major direction. 

2. The barsets are approved when installed in accordance with the instructions detailed on document SB/3BS/INS (Issue 4). 



Tel: +44 (0)1733 361511 • Fax: +44 (0)1733 361512 




Product 

Name 

Extendor 

Eclipse 

Type 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Fixed security grille 0.5 3.58 0.3 5.75 3 869a/01 

Cert. 

No. 

436 20 Nov 2011



Product 

Name 

Type 

Single sash collapsible 


Double sash collapsible 


Flexi single and multiple 

sash collapsible security 

grille 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

0.625 2.7 0.39 5.75 3 

0.625 2.7 0.44 11.5 1 3 

0.625 2.7 0.44 Unlimited 1 3 

Cert. 

No. 


Product Name Type Lock Compatible 

Cylinders 

Extendor Eclipse Single sash collapsible security grille Extendor Eclipse CL03 lock 

with CL03 cylinder guard 2 


Double sash collapsible security 

grille 

‘Flexi’ single and multiple sash 

collapsible security grille 

Compatible Cylinders Cylinders 

1 Assa dp4400 single europrofile 

2 CISA AP3S single europrofile 

3 Kaba Quattro Plus single europrofile 


Recessed track and deep rail cover channel. 


Extendor Eclipse CL03 lock 

1 to 3 


Extendor Eclipse CL03 lock 

1 to 3 


Configuration 

Substrate 

Brickwork Concrete 

Blockwork 

Concrete Structural 

Timber 

Reveal 

Internal Face 

Notes 

1. The maximum width of any sash is 5.75 m. 

2. The CL03 cylinder guard is only required for protecting cylinders on the attack side of the grille. 

3. Installation into other substrates should be assessed by LPCB to ensure the installation method offers compatible resistance to 

attack. 

Safeguard Security, a trade name of WBH Industries 

Unit 5, 229 Torrington Avenue, Coventry CV4 9HN, United Kingdom 

Tel: +44 (0)2476 470 600 • Fax: +44 (0)2476 471 600 

E-mail: info@safeguardsecurity.co.uk • Website: www.safeguardsecurity.co.uk 



Product 

Name 

LPC1 System 

Type 

Single gate, collapsible security 

grille 

Double gate, collapsible 


Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. 

No. 

0.594 3.0 0.233 6.0 1 418a/01 

0.594 3.0 0.405 12.0 1 

20 Nov 2011 437




LPCB Ref. Product Name Type Locks Cylinder 

No. 

418a/01 LPC1 System Single and double gate 

collapsible security grille 

Adams Rite MS 1900 hook 

lock 

Sofi 5-pin single Europrofile 

Approved Installations Configurations 1 

Configuration 

Substrate 

Brick Concrete Blockwork Timber Steel 

Reveal 


Note: 

1. This assumes installation direct to the substrate and not via intermediate substrates, such as plasterboard. 

Security Blinds Limited 

Units 3 A/B, Hope Street, Thornhill Industrial Estate, Rotherham S60 1LH, United Kingdom 

Tel: +44 (0)1709 363535 • Fax: +44 (0)1709 364512 

E-mail: info@securityblinds.co.uk • Website: www.securityblinds.co.uk 


Security Blinds 

Product Name Model Type Minimum 

Height 

(m) 

Secur 950031 Single leaf inward 

opening vertical 

blind unit 

950032 Single leaf inward 

opening vertical 

blind unit with 

transom 

950033 Double leaf 

horizontal sliding 

verticial blind unit 

950034 Double leaf 

horizontal sliding 

vertical blind unit 

with transom 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

SecurityRating 

Cert. No. 

0.5 0.324 2.5 1.399 2 854a/01 

0.5 0.324 2.5 1.3999 2 

0.5 0.918 2.5 3.018 2 

0.5 0.918 2.5 3.018 2 


LPCB Ref. Model Lock Cylinder 

No. 

854a/01 950031 CISA 46270-25 tw o w ay locking system C2000 European single europrofile cylinder 

950032 

950033 

950034 


Configuration 

Substrate 

Brick Concrete Blockw ork 

Reveal 

Note: 

1. This assumes installation direct to the substrate and not via intermediate substrates, such as plasterboard. 

438 20 Nov 2011



Simbars (UK) Limited 

Unit 2, 46 Ashton Vale Road, Ashton, Bristol BS3 2HQ, United Kingdom 

Tel: +44 (0)117 953 1444 • Fax: +44 (0)117 963 1444 

E-mail: info@simbars.co.uk • Website: www.simbars.co.uk 


Fixed Security Bar Sets 


Structural 

Opening 

Height (m) 

Simbars 

security bar sets 

SR3 

Simbars 

security bar sets 

SR4 



Internally face 

fixed security bar 

set 



Internally face 

fixed security bar 

set 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Cert. 

No. 

0.6 8.0 0.6 6.0 3 932a/01 

0.14 7.54 0.14 5.54 3 

0.225 8.0 0.225 6.0 4 932a/02 

0.227 7.54 0.29 5.54 4 

Note 

1. The bar sets are approved when installed directly to structural concrete using the fixings specified on drawings A1-00056 Revision 

F and A1-00104 Revision B (Internal face fixed) and A1-00057 Revision E and A1-00108 Revision C (Reveal mounted). The 

approval does not cover the bar sets when mounted to alternative substrates or via intermediate substrates such as plasterboard. 

SWS UK 

Hornby Road, Claughton, Lancaster LA2 9LA, United Kingdom 

Tel: +44 (0)1524 772400 • Fax: +44 (0)1524 772411 

E-mail: info@swsuk.co.uk • Website: www.swsuk.co.uk 




Height 

(m) 

SeceuroGuard 1001 Single gate 

collapsible security 

grille 

SeceuroGuard 1001 

"Fixed" 


"Floating" 


SeceuroGuard 1001s 


"Fixed" 


"Floating" 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

1 0.5 3 3 1 390a/01 

Fixed security grille 1 0.5 3 3 1 

Single gate 


grille 

1 0.5 3 3 1 

Double gate 

1 1 3 6.5 1 


grille 

Single gate 

1 0.5 3 3 1 390a/03 


grille 

Fixed security grille 1 0.5 3 3 1 

Single gate 


grille 

1 0.5 3 3 1 

20 Nov 2011 439




Height 

(m) 

SeceuroGuard 1001s Double gate 


grille 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

1 1 3 6.5 1 

Cert. 

No. 


LPCB Ref. Trade Name Type Locks 

No. 

390a/01 SeceuroGuard 1001 Single gate collapsible 


Viro 8300 extensible gate 

lock with 5-pin cylinder 

SeceuroGuard 1001 Fixed security grille N/A 

“Fixed” 


“Floating” 





SeceuroGuard 1001 Double gate collapsible 




390a/03 S-lattice SeceuroGuard 

1001s 





S-lattice SeceuroGuard Fixed security grille N/A 

1001s “Fixed” 

S-lattice SeceuroGuard 

1001s “Floating” 





S-lattice SeceuroGuard 

1001s 

Double gate collapsible 





Accessory 

Associated Products (LPCB Ref. No. 390a/...) 

1 3 

Folding bottom track 1 


Configuration 

Substrate 


Steel 

Structural 

Timber 

Reveal 

Internal face fixed 2 

Notes 

1. The folding bottom track is approved as an option on the single gate and double gate SeceuroGuard 1001 and SeceuroGuard 

1001s models only. 


The Expanded Metal Company Limited 

P.O.Box 14, Longhill Industrial Estate (North), Hartlepool TS25 1PR, United Kingdom 

Tel: +44 (0)1429 867 388 • Fax: +44 (0)1429 867 355 

E-mail: fencing@expamet.co.uk • Website: www.expandedmetalfencing.co.uk 


440 20 Nov 2011

Fixed Security Window Guard 

Product 

Name 

Type 

Minimum 

Structural 

Opening 

Height (m) 

Class 3 

Window 

Guard 

Maximum 

Structural 

Opening 

Height (m) 



Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Security 

Rating 

Rectangular 

0.5 4.0 0.5 2.0 3 731d/01 

vertical bars 1 

security window 

guards with square 

Rectangular 

security window 

guards with round 

vertical bars 2 0.5 4.0 0.5 2.0 3 731d/02 

Cert. 

No. 

Notes 

1. The window guards are approved when reveal mounted directly into solid brickwork or concrete structures of equivalent resistance 

to attack in accordance with the installation instructions contained in documents C3WG/RHS/P1 (Issue B), C3WG/RHS/P2 (Issue 

A), C3WG/RHS/P3 (Issue A) and C3WG/RHS/P4 (Issue A). 

2. The window guards are approved when reveal mounted directly into solid brickwork or concrete structures of equivalent resistance 

to attack in accordance with the installation instructions contained in drawings C3WG/BAR/P1 (Issue B), C3WG/BAR/P2 (Issue A), 

C3WG/BAR/P3 (Issue A) and C3WG/BAR/P4 (Issue A). 

3. The approval does not cover the window guards when mounted to alternative substrates or via intermediate substrates such as 

plasterboard. 

Trellicor (Pty) Limited 

20 Aberdare Drive, Phoenix Industrial Park, Durban, South Africa 

Tel: +27 31 500 4301 • Fax: +27 31 507 2129/3973 



Product 

Name 

Model Type Minimum 

Height 

(m) 

Trellidor 

Trojan II 

Trellidor 

Trojan II 

EMESC 

Standard 

Flexi 

Fixture 

Double 

Double 

flexi 

Standard 

Flexi 

Double 

Double 

flexi 

Single gate 

collapsible 


Single gate 

collapsible 


Single gate 

collapsible 


Single gate 

collapsible 


Double gate 

collapsible 


Double gate 

collapsible 


Single gate 

collapsible 


Single gate 

collapsible 


Double gate 

collapsible 


Double gate 

collapsible 


Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

1.195 1.0 3.0 5.0 2 474a/04 

1.195 1.0 3.0 5.0 2 

1.195 1.0 3.0 5.0 2 

1.195 2.0 3.0 10.0 2 

1.195 2.0 3.0 10.0 2 

1.780 1.0 3.0 5.0 2 474a/05 

1-780 1.0 3.0 5.0 2 

1.780 2.0 3.0 10.0 2 

1.780 2.0 3.0 10.0 2 


20 Nov 2011 441



LPCB Ref. 

No. 

Trade 

Name 

474a/04 Trellidor 

Trojan II 

474a/05 Trellidor 

Trojan II 

EMESC 

Model 

Lock 

Trellidor 

single 

europrofile 

Cylinder 

Trellidor 

double 

europrofile 

Trellidor double 

europrofile 

(key:key) (key:thumbturn) 1 

Standard Trellilok (Mark IV) - 

Flexi Trellilok (Mark IV) - 

Fixture N/A - - - 

Double Trellilok (Mark IV) - 

Double Trellilok (Mark IV) 

- 

flexi 

 

 

Standard Trellilok (Mark IV) - - 

Flexi Trellilok (Mark IV) - - 

Double Trellilok (Mark IV) - - 

Double 

flexi 

Trellilok (Mark IV) 

- - 

LPCB Ref. 

No. 

Brick Concrete 

Blockwork 

Product Name Configuration Substrate 

Stone 

Structural 

Steel 

Structural 

Timber 

474a/04 Trellidor Trojan II Reveal 

474a/05 Trellidor Trojan II 

EMESC 

Notes 

Reveal 

1. Thumbturn is located on non-attack side of the grille with a protection shroud. 



Security grilles 

Product Name Model Type Minimum 

Height 

(m) 

Trellidor Plus Standard Single gate 


grille 

Flexi Single gate 


grille 

Fixture Single gate 


grille 

Double Double gate 


grille 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. No. 

0.945 0.6 3.0 5.0 1 474b/01 

0.945 1.0 3.0 5.0 1 

0.945 0.6 3.0 5.0 1 

0.945 1.0 3.0 10.0 1 


LPCB Ref. No. 

474b/01 

Model 

Lock 

Cylinder 

Trellidor single Trellidor double europrofile 

europrofile 

Standard Trellilok (Mark IV) 

Flexi Trellilok (Mark IV) 

Fixture N/A N/A N/A 

Double Trellilok (Mark IV) 

442 20 Nov 2011




Accessory 

Hinged bottom track 

Removable bottom track 

Approved Product (LPCB Ref. No. 474b/...) 

01 

 

 

Approved Instllation Configurations 1 

Configuration 

Substrate 

Brick Concrete Structural Steel Structural Timber 

Reveal 

Note 


20 Nov 2011 443


SECURITY SHUTTERS 

Security shutters listed in this section are approved to LPS 1175 Requirements and testing procedures for the 



In addition to approving shutters to LPS 1175, LPCB also offer security performance approval of shutters to 

EN1627 aswell as approvals covering other aspects of shutter performance including weathertightness, 

thermal performance, fire and acoustics. 

Aluroll Limited 

Mile Oak Industrial Estate, Maesbury Road, Oswestry, Shropshire SY10 8GA, United Kingdom 

Tel: +44 (0)800 977 8975 • Fax: +44 (0)1691 671 482 

E-mail: enquiry@aluroll.co.uk • Website: www.aluroll.co.uk 


Security Shutters 

Product Type 

Name 

E37 

Elite 

T77 

Elite (1) 

V77 

Elite 

E77 

Elite 

Externally 

face fitted 

double skin 

aluminium 

roller shutter 

Internally 

face fitted 

double skin 

insulated 


Internally 

face fitted 

aluminium 


with vision 

slats 

Internally 

face fitted 

aluminium 


Minimum 

Structural 

Opening 

Height 

(m) 

Maximum 

Structural 

Opening 

Height 

(m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Maximum Compatible 

Door Locking 

Area Devices 

(m 2 

Security 

Rating 

Cert. 

No. 

0.9 4.0 0.77 3.0 8.5 A 1 931a/01 

0.9 2 5.2 0.9 5.0 20 B 1 931a/02 

0.9 2 5.2 0.9 5.0 25 B 2 931a/03 

0.9 2 5.2 0.9 5.0 25 B 2 931a/04 


Compatible 

Locking 

Device 

External 

Internal 

A Tw o Hopkins bullet H75 locks plus w ireless keypad and/or keyfob Push button motor control 4 

motor control 3 and external manual override handle protected by 

Alukon 380370100 locking cap 

B Wireless keypad and/or keyfob motor control 3 Push button motor control 4 w ith 

internal manual override handle 5 


Locking / Operating Devices 

444 20 Nov 2011

Trade Name Type 




Masonry Steelw ork Aluminium 

E37 Elite Externally face fitted double skin aluminium roller shutter 

T77 Elite Internally face fitted double skin insulated roller shutter 2 

V77 Elite Internally face fitted aluminium roller shutter w ith vision slats 2 

E77 Elite Internally face fitted aluminium roller shutter 2 

Notes: 

1. The T77 Elite is also marketed as an Elite garage door. That is available over the same size range and with same locking devices. 

2. The T77 Elite, V77 Elite and E77 Elite roller shutters must have a minimum structural opening height of 2 m when installed on 

aluminium substrates. 

3. The resistance of the wireless keypad and keyfob motor control to “non-mechanical” attack is not covered by this approval as they are 

outside the scope of LPS 1175. Likewise, the approval does not cover possible effects of any susceptibilities relating to the 

functionality and performance of the wireless keypad and keyfob motor control equipment. It is therefore recommended that 

specifiers’ satisfy themselves that the components used are either resistant other forms of tampering/abuse, or that they are suitably 

protected from such tampering/abuse and are resistant to any environmental conditions/interference that may cause the locking 

system to disengage. 

4. The push button controller should be located on the protected side of the shutter at least 1.5 m from the shutter curtain. 

5. The manual override handle should be stored on the protected side of the shutter at least 1.5 m from the shutter curtain. 



Tel: +44 (0)1204 545801 • Fax: +44 (0)1204 545800 




Product Type 

Name 

A320 

Rolling 

shutter 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

2 7 2.5 9 4 131b/01 


LPCB Ref. Product Type 

Lock 

No. Name 

131b/01 A320 Rolling Shutter H75H Euro Guide Bullet Pin Lock 

Note 

1. A centre ground lock must be provided on shutters of greater than 5 metres width. 



Product Name Model Type Security Rating Cert. No. 

Centurion A305SS Roller shutter with solid single skin steel lath 1 131e/01 

A305PS Roller shutter with perforated single skin steel lath 1 131e/02 

A305SA Roller shutter with solid single skin aluminium lath 1 131e/03 

A305PA Roller shutter with punched aluminium lath 1 131e/04 

A305PG Roller shutter with punched and glazed aluminium lath 1 131e/05 

A310SS Roller shutter with solid single skin steel lath 2 131e/06 

A315 Roller shutter with reinforced double skin aluminium lath 3 131e/07 

Configurations, Sizes and Locking 

20 Nov 2011 445



Models Orientation Operation Minimum 

Height 

(m) 

A305SS 

A305PS 

A305SA 

A305PA 

A305PG 

A310SS 

A315 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Locking 

Reveal Push up 1 3 1 3 Hopkins H75 pin lock fitted to internal 

or external face 

Tube motor 1 7 1 7 Hopkins H75 pin lock fitted to internal 


Internal Push up 1 3 1 3 Hopkins H75 pin lock fitted to internal 

face 


face 

Direct drive 1 7 1 7 Hopkins H75 pin lock fitted to internal 

face 

Reveal Push up 1 3 1 3 Hopkins H75 pin lock fitted to internal 




Internal Push up 1 3 1 3 Hopkins H75 pin lock fitted to internal 

face 


face 


face 

Reveal Tube motor 1 7 2 7 Hopkins H75 pin lock fitted to internal 

face 

Internal Tube motor 1 7 2 7 Hopkins H75 pin lock fitted to internal 

face 


face 

Note: 

1. The approval applies to the shutters when installed strictly in accordance with the instructions provided with the product. 

Shellcast Systems Limited 

Camel House, Six Ashes, Bridgnorth WV15 6ER, United Kingdom 

Tel: +44 (0)1562 750 700 • Fax: +44(0)8712 453 553 

E-mail: technical@shellcast-shutters.co.uk • Website: www.shellcast-shutters.co.uk 



Product 

Name 


Clear 

Opening 

Height 

(m) 

Linframe CD38.1 Built-in rolling 

shutter 

CD38.2 Built-in rolling 

shutter 


shutter 

CD38/P.1 Built-in rolling 

shutter 

CD38/S.1 Built-in rolling 

shutter 


shutter 


shutter 

Minimum 

Clear 

Opening 

Width 

(m) 

Maximum 

Clear 

Opening 

Height 

(m) 

Maximum 

Clear 

Opening 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

0 0.4 6 5 1 707a/01 

0 0.4 6 5 2 707a/02 

0 0.4 6 5 3 (2) 707a/03 

0 0.4 6 3 1 707a/04 

0 0.4 6 3 1 707a/05 

0 0.4 6 5 1 707a/06 

0 0.4 6 5 2 707a/07 

Notes 

446 20 Nov 2011



1. The approval applies to the shutters when installed strictly in accordance with the instructions provided with the product 

2. To achieve this grade the lockable override cover plate must be fitted and locked, and the key removed to a secure location. 

SWS UK 


Tel: +44 (0)1524 772400 • Fax: +44 (0)1524 772411 




Product Name Type Lath Minimum 

Height 

(m) 

SeceuroShield Roller 

7501 shutter 

SeceuroShield Roller 

3801 

SeceuroVision 

7501 

shutter 

Roller 

shutter 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

Solid 0.6 0.9 4.7 6 1 390a/04 

Solid 0.9 0.9 4 3 1 390a/02 

Perforated 0.6 0.9 4.7 6 1 390a/05 

Compatible Locking Devices and Method of Shutter Operation 

LPCB Ref.No. Product Name Type Operation 

Motorised Manual Simbac 

6C3.3227 

cylinder 

lock 

Lock 

Hopkins 

H75 pin 

lock 

390a/02 SeceuroShield 3801 Roller shutter 

390a/04 SeceuroShield 7501 Roller shutter 

390a/05 SeceuroVision 7501 Roller shutter 

 

1 

 

1 

 


Accessory 

Associated Products (LPCB Ref. No. 390a/..) 

02 2 04 05 

Manual override handle 

Approved Installation Configurations 3 Brick Concrete Structural 

LPCB Ref. No. 

Product Name 

390a/02 SeceuroShield 3801 

390a/04 SeceuroShield 7501 

390a/05 SeceuroVision 7501 

Configuration 

Substrate 

Structural 

Steel Timber 

Reveal 


External face fixed 

Reveal 


Reveal 


20 Nov 2011 447



Notes 

1. The Hopkins H75 pin lock is only approved on shutters over 3m wide operated by a motor drive axle. 

2. The manual override option is only approved on internally face fixed units with internally face fixed motor boxes. 


448 20 Nov 2011


PERFORATED SECURITY SCREENS 

Perforated security screens (otherwise referred to as security screens and void protection screens) listed in 

this section are approved to LPS 1175 Requirements and testing procedures for the LPCB approval and 

listing of intruder resistant building components, strongpoints, security enclosures and free-standing barriers. 

In addition to approving security screens to LPS 1175, LPCB also offer security performance approval of such 

products to EN1627. 

SWS UK 


Tel: +44 (0)1524 772400 • Fax: +44 (0)1524 772411 


Certificate No: 390c/01 to LPS 1175: Issue 6 

Perforated Security Screens 


Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. No. 

SeceuroMesh Fixed security screen 0.25 0.25 2.54 1.29 1 390c/01 

Approved Installation Configurations (1) 

Configuration 

Substrate 

Structural Concrete Brick Timber 

Steel Blockwork 

External face 

Reveal 

Note 

1. This assumes installation direct to substrate and not via intermediate substrates. 



Tel: +27 31 500 4301 • Fax: +27 31 507 2129/3973 


Perforated Security Screens 

Product 

Name 


Height 

(m) 

Griffinguard Standard Fixed security 

Griffinguard 

(3) 

Double 

screen 

Fixed security 

screen 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security 

Rating 

Cert. 

No. 

0.4 0.4 1.3 2.5 1 474a/03 

0.4 1.4 2.6 2.5 1 

Note 

1. The Griffinguard is approved for either externally face fixing or reveal mounting into brickwork, lightweight blockwork, concrete 

blockwork, structural steelwork or timber. 

20 Nov 2011 449


LOUVRE VENTS 

Louvre vents listed within this section have been evaluated in accordance with LPS 1175 Specification for 

testing and classifying the burglary resistance of building components, strongpoints and security enclosures. 



Tel: +44 (0)1234 826316 • Fax: +44 (0)1234 826319 



Louvre Vents 


Louvre 

Height 1 (m) 

Maximum 

Louvre 

Height 1 (m) 

Minimum 

Louvre 

Width 2 (m) 

Maximum 

Louvre 

Width 2 (m) 

Security 

Rating 

Cert. No. 

SR4 Louvre Steel security louvre vent 0.35 2.5 0.35 1.15 4 516b/01 

Compatible Substrates 3 

Cert. No. 

516b/01 

Substrate 

Steelw ork 

Reinforced blockw ork 

Reinforced concrete 

Partition w all of ‘Wilton’ / ‘Halton’ construction via Sapele timber stud 4 

Partition w all of equivalent resistance to LPS 1175 SR4 via Sapele timber stud 4 

lining an aperture in steelw ork, reinforced blockw ork or reinforced concrete 

Notes: 

1. The height of the louvre vent is measured perpendicular to the plane of the louvre blades. 

2. The width of the louvre vent is measured in the plane of the louvre blades. 

3. The vents are approved for installation in accordance with the instructions contained in documents D11767.15 (revision I) and 

D11767.23 (revision B). 

4. Sapele timber stud should be at least 100 mm by 70 mm. 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 


Certificate No: 450h to LPS 1175: Issue 6 

Louvre Vents 

Product Type 

Name 

Louvre 

Vent 

Minimum 

Louvre Module 

Height (m) 

Maximum 

Louvre Module 

Height (m) 

Minimum 

Louvre Module 

Width (m) 

Maximum 

Louvre Module 

Width (m) 

Security 

Rating 

Modular 

0.2 1 1 0.6 1.2 1 5 450h/01 

system 1 

louvre vent 

Cert. 

No. 


LPCB Trade Name Type Installation method 


Ref. No. 

Reinforced Concrete Steelwork 

450h/01 Louvre Vent Modular louvre 

vent system 

Reveal fitting only 

Notes 

450 20 Nov 2011


LOUVRE VENTS 

1. The louvre modules can be bolted together to form a larger panel. The bolted together panels can theoretically fill any 

structural opening larger than the smallest module. 

2. The Louvre Vent may also be fitted directly above the Technocover Sentinel UltraSecure doorsets listed on LPCB 

certificate 450f without compromising their Security Ratings to LPS 1175. 

20 Nov 2011 451


GARAGE DOORS 

Theft of equipment from garages is fairly common due to the value of equipment often stored within them and 

the ease with which burglars can overcome many garage doors. Burglars also target garages that provide 

access to the inside of the house via internal pedestrian doors because the burglars can: 

attack the internal doorset unobserved by people in surrounding properties; and/or 

use tools stored within the garage to aid their entry into the house. 

Specifying garage doors that provide proven levels of resistance to forced entry therefore plays an important 

part in reducing: 

Theft of equipment from garages. 

Theft of items from houses resulting from entry through adjoining garages. 

Good physical security will also help to protect against attempted arson, especially if the garage doors have 

dual security and fire approval through LPCB. 

Garage doors listed in this section meet the requirements of LPS 1175 Requirements and testing procedures 

for the LPCB approval and listing of intruder resistant building components, strongpoints, security enclosures 

and free-standing barriers. 

In addition to fitting garage doors approved to LPS 1175, specifiers keen to improve the security of their 

garages should also consider using security enclosures approved to LPS 1175 and fitting intruder detection 

equipment approved by LPCB and installed by a competent installer. Please refer to Section 4 for a list of 

approved security enclosures and Section 1 for a list of approved intruder detection equipment. 

LPCB also offer security performance approvals of garage doors to EN1627. 



Tel: +44 (0)800 977 8975 • Fax: +44 (0)1691 671 482 



Garage Doors 

Product Type 

Name 

Elite 

Internally 

face fitted 

double skin 

insulated 

roller 

shutter 

Minimum 

Structural 

Opening 

Height (m) 

Maximum 

Structural 

Opening 

Height (m) 

Minimum 

Structural 

Opening 

Width (m) 

Maximum 

Structural 

Opening 

Width (m) 

Maximum 

Door 

Area 

(m 2 ) 

Compatible 

Locking 

Devices 

Security 

Rating 

0.9 5.2 0.9 5.0 20 B 1 931a/02 

Cert. 

No. 

Notes 

1 The Elite garage door is also marketed as a T77 Elite roller shutter. That is available over the same size range and 

with same locking devices. 

2 Refer to Volume 2 Part 4 Section 5.6 for full details of the locking systems and accessories approved on the T77 Elite 

roller shutter and other approved roller shutters manufactured by Aluroll Limited. 

452 20 Nov 2011


GARAGE DOORS 

SWS UK 


Tel: +44 (0)1524 772400 • Fax: +44 (0)1524 772411 



Garage Doors 


Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Height 

(m) 

Maximum 

Width 

(m) 

Security Rating 

Cert. No. 

SeceuroGlide Excel Garage door 1 1.5 3.85 5.2 1 390b/01 


Accessory 

Associated Products (LPCB Ref. No. 390b/...) 

Bullet locks 

01 

 

Approved Installation Configurations 

Configuration 

Substrate 

Brick Blockwork Structural 

Steel 

Structural 

Timber 

Reveal 1 

Internal face fixed 1 

Notes 


2. No assessment has been made of the remote control device. 

20 Nov 2011 453


ACCESS COVERS AND HATCHES 

Many important facilities, especially those of utility companies, are unmanned and remote from the main 

business. At the request of the utility companies, access covers protecting items such as valves, switchgear 

and meters are now security rated to provide protection against malicious attack. 

LPCB approves access covers to LPS 1175 Requirements and testing procedures for the LPCB approval and 

listing of intruder resistant building components, strongpoints, security enclosures and free-standing barriers. 

The approval procedures and conditions that apply to access covers are the same as those that apply to 

security doors and shutters. 

It is important that specifiers only select access covers that are covered by the scope detailed on the 

certificate since products that fall outside that scope may not provide an equivalent level of security. 

It is also important to ensure that the products are installed in accordance with the manufacturer’s instructions 

and that all exposed fixings, the substrate into which the device is fitted and the locking mechanisms are 

regularly checked to ensure that they are in good condition and that they have not been tampered with. 

Products that have been certified by LPCB should be marked with a label indicating the grade of security 

offered, LPCB approval mark and certificate number. 

Aquacast (Fabrications) Limited 

Unit 3 Power Park, Towers Business Park, Rugeley, Staffordshire WS15 1UZ, United Kingdom 

Tel: +44 (0)1889 572620 • Fax: +44 (0)1889 572629 

E-mail: sales@aquacastltd.com • Website: www.aquacastltd.com 


Horizontal Access Cover 

Product 

Name 

Type Minimum 

Length of 

Internal 

Opening (mm) 

Aquaguard Single leaf 

horizontal 

access cover 

Maximum 

Length of 

Internal 

Opening (mm) 

Minimum 

Width of 

Internal 

Opening (mm) 

Maximum 

Width of 

Internal 

Opening (mm) 

Security 

Rating 

Cert. No. 

250 1200 250 1200 4 1020a/01 

Compatible Padlocks 1,2 

Padlock Cylinder LPCB Cert. No. 1020a/01 

Abloy PL340/25 Abloy Protec 



Abloy PL340/25 Abloy Exec 

Abloy PL342 Abloy Protec 


Abloy PL342 Abloy Disklock Pro 

Abloy PL342 Abloy Exec 

Abloy PL350/25 Abloy Protec 



Abloy PL350/25 Abloy Exec 

Accessories 1 

454 20 Nov 2011



Accessory Code LPCB Cert. No. 1020a/01 

Alarm bracket AB1 

Cable holes 3 CH1 

Extended frame and lid EX1 

Ladder type safety grill FP1 

Split type safety grill FP2 

Extended low er shroud 4 LS1 

Notes: 

1. Certification does not cover the use of padlocks or accessories other than those listed. Utilisation of unlisted padlocks and/or 

accessories may affect the level of security offered by the access cover. 


3. Cable holes (accessory CH1) are only available on access covers with the extended frame and lid (accessory EX1). 

4. The extended lower shroud (accessory LS1) must be used when the substrate onto which the access cover is mounted does not 

extend horizontally from the front of the main body of the access cover by at least 300 mm. 

5. The access cover is approved when installed in accordance with the instructions on document AG-LPS4-Fit (Revision 3, dated 2 

March 2011). 

Midas Technologies (GB) Limited 

Unit A, Roundhouse Close, Eastern Industry, Peterborough PE1 5TA, United Kingdom 

Tel: +44 (0)1733 342600 • Fax: +44 (0)1733 346672 

E-mail: sales@midastech.co.uk • Website: www.midastech.co.uk 


Horizontal Access Covers 


Internal 

Opening 

Length 

(mm) 

Maximum 

Internal 

Opening 

Length 

(mm) 

Minimum 

Internal 

Opening 

Width 

(mm) 

Maximum 

Internal 

Opening 

Width 

(mm) 

Security 

Rating 

Aquavent 2004 Single leaf horizontal access cover 200 1200 200 1200 4 421a/01 

Aquavent Single leaf (twin lid 1 ) horizontal 200 2000 200 2000 4 421a/02 

2004/TC 

access cover 

Aquavent 

2004/DC 

Double leaf horizontal access cover 1200 4000 1200 2000 4 421a/03 

Cert. 

No. 

Accessories 

Accessory 

Access Covers (LPCB Ref. No. 421a/..) 

01 02 03 

Safety grill/ladder 

 

Deep pan base frame 

Alarm bracket and switch plate 


20 Nov 2011 455



Padlock Designation 

Cylinder 


01 02 03 





























ERA “Fortress” 977-91 ERA 6-pin 

Rotalok 60/12/ST N/A 

Rotalok 60/12/SE N/A 

Rotalocken 22RTLKNX Locken CL-PL2WR 

electronic cylinder 

 

Notes 

1. This model incorporates a secondary inner lid. 

2. Certification does not cover the use of padlocks or accessories other than those listed above. Utilisation of unlisted padlocks and/or 


3. The 'user friendliness' of employing the padlocks listed above has not been assessed as this is beyond the scope of LPS 1175: 

Issue 5. 

4. The resistance of the electronic cylinder to “non-mechanical” attack has not been assessed as it is outside the scope of LPS 1175. 

Likewise, the assessment has not covered possible effects of any susceptibilities relating to the functionality and performance of the 

keys that may be used to operate the cylinder. It is therefore recommended that specifiers and installers satisfy themselves that the 

components used are either resistant to mechanical and other forms of tampering/abuse and are resistant to any environmental 

conditions/interference that may cause the padlock to disengage. 

Steelway Fensecure Limited t/a Steelway Brickhouse 

Brickhouse Lane, West Bromwich, West Midlands B70 0DY, United Kingdom 

Tel: +44 (0)121 521 4524 • Fax: +44 (0)121 521 4551 

E-mail: sales@steelwaybrickhouse.co.uk • Website: www.steelway.co.uk 


456 20 Nov 2011




Product 

Type 

Name 

Sentry 

Single leaf horizontal 

access cover 

Single leaf horizontal valve 

cover 


ventilator cover 

Twin leaf in-line hinged 

horizontal access cover 

Twin leaf end-hinged 

horizontal access cover 

Minimum 

Length of 

Internal 

Opening 

(mm) 

Maximum 

Length of 

Internal 

Opening 

(mm) 

Minimum 

Width of 

Internal 

Opening 

(mm) 

Maximum 

Width of 

Internal 

Opening 

(mm) 

Security 

Rating 

Cert. 

No. 

300 1200 300 1100 4 645a/01 

200 300 200 300 4 645a/02 

200 500 200 500 4 645a/03 

1200 2200 600 1000 4 645a/04 

1200 2200 600 1500 4 645a/05 


Accessory 

Sentry Access Cover (LPCB Ref. No. 645a/…) 

01 02 03 04 05 

Safety grid 1 

Safety grid/Exit support 1 

Alarm Bracket 

Junction box bracket 

External seal version 

 

External vent and seal version 


Padlock Designation Cylinder 

Sentry Access Cover (LPCB Ref. No. 645a/…) 

01 02 03 04 05 










Kaba KP15.0000C5-RB20 Kaba 20 (Armoured) 2 




Rotalok 60/12/ST Assa Twin-Combi 


Rotalok 60/12/ST Kaba 20 (standard) 2 

Notes 

1. The safety grid/exit support is only available on access covers with an internal clear opening length of at least 400mm. 


20 Nov 2011 457





Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 





Internal 

Opening 

Length 

(mm) 

Ultra Secure DV 


Ultra Secure DV (Small Lock) 

Ultra Secure DV4 Twin Leaf 

(End Hinged) 

Ultra Secure DV4 Twin Leaf 

(In-line Hinged) 

Ultra Secure DV4 Triple Leaf 

(In-line Hinged) 

Ultra Secure DV4 Triple Leaf 

(Special) 

SHH1/DV 

SHH2/DV 

SHH3/DV 

SHHM/DV 

Maximum 

Internal 

Opening 

Length 

(mm) 

Minimum 

Internal 

Opening 

Width 

(mm) 

Maximum 

Internal 

Opening 

Width 

(mm) 

Security 

Rating 

Cert. 

No. 

8 150 1100 150 1100 4 450a/01 

Single leaf horizontal 150 1100 150 1100 4 450a/02 

access cover 8 

Twin leaf horizontal 1100 2200 1100 1800 4 450a/04 


Twin leaf horizontal 1100 2400 600 1100 4 450a/05 


Triple leaf horizontal 1800 3600 600 1100 4 450a/06 


Triple leaf horizontal 1800 3600 1100 1800 4 450a/07 


Single leaf flush access 400 1200 400 1200 3 450a/09 

cover 

Twin leaf flush access 1200 2400 400 1200 3 450a/10 

cover 

Triple leaf flush access 1500 3000 400 1200 3 450a/11 

cover 

Multiple leaf flush 2000 12000 7 2000 2400 3 450a/12 

access cover 


Padlock Designation Cylinder 


01 02 04 05 06 07 09 10 11 12 



















458 20 Nov 2011










Rotalok 60/12/ST Abloy Disclock Pro 



Rotalok 60/12/ST Assa Twin-Combi 



Accessories 

Accessory 


01 02 04 05 06 07 09 10 11 12 

F3 skirting frame 

K2 Hasp and staple 

Viper alarm bracket 

Ladder/safety grid 

400 x 50 mm inner frame ventilation holes 

Standard vent option 

Maxi vent option 

Undercover bracing 'A15' option 

Undercover bracing 'B125' option 

Undercover bracing 'C250' option 

Notes 

1. The Abloy PL240/25 and PL340/25 padlocks should only be used on Ultra Secure DV access covers that have been fitted with the 

K2 hasp and staple. 

2. The Abloy PL250/25, PL350/25 and Chubb 1K23c padlocks should not be used on Ultra Secure DV access covers that have been 

fitted with the K2 hasp and staple. 

3. If the Abloy PL250/25 and PL350/25 padlocks are to be fitted to access covers on upstands greater than 250 mm tall, the horizontal 

distance between the locking face of the access cover and the outside edge of the upstand must be at least 200 mm. 


5. Certification does not cover the use of padlocks or accessories other than those listed above. Utilisation of unlisted padlocks and/or 


6. The 'user friendliness' of employing the padlocks listed above has not been assessed as this is beyond the scope of LPS 1175: 

Issue 5. 

7. The configurations of multi leaf access covers falling within the scope of this approval are defined on Technocover document 

SHH/DV/ASSY-08 dated 12 September 2006. 

8. This product is available with or without an inner lid. This does not effect the security rating of the product. 

20 Nov 2011 459


SECURE WALLING SYSTEMS 

Walling systems listed in this section are approved to LPS 1175 Requirements and testing procedures for the 

LPCB approval and listing or intruder resistant building components, strongpoints, security enclosures and 


In order to comply with the terms of the approval, the walling systems must be designed and installed in 

accordance with the relevant system manuals noted within the product entry. 

Unless otherwise stated, the approvals cover: 

Plain systems (that is, excluding service penetrations, ducts or other openings such as doors and 

windows). 

Resistance to the creation of an access hole, within the area of the barrier, through which it is 

possible to pass the 225 mm by 400 mm elliptical test block defined in LPS 1175. 

It is recommended that evidence is sought to confirm compatibility of any doors, windows etc to ensure the 

combined assembly offers the required security rating. Where such compatibility has been proven, this is 

indicated in the relevant listing. 



Tel: +44 (0)191 258 5052 • Fax: +44 (0)191 259 5742 



Secure Partition Walling System 

Product 

Name 


Height (m) 

Maximum 

Height (m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Security 

Rating 

Cert. 

No. 

Securiclad Walls with 

2.5 Unlimited 2.5 Unlimited 3 142d/01 

horizontally laid 

panels 

Walls with vertically 2.5 6.0 0.25 Unlimited 3 

laid panels 

Walls with 

2.5 Unlimited 2.5 Unlimited 4 142d/02 

horizontally laid 

panels 

Walls with vertically 

laid panels 

2.5 6.0 0.25 Unlimited 4 



Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Thickness 

(m) 

SR3/SR4 panel (mineral w ool) 0.25 1.19 2.5 6 0.1 

Ceiling panel (mineral w ool) 0.25 1.19 1 6 0.1 

SR3/SR4 panel (PIR) 0.25 1.19 2.5 6 0.1 

Ceiling panel (PIR) 0.25 1.19 1 6 0.1 

Products Compatible with the Securiclad Security Panel System 2,3 

460 20 Nov 2011

Manufacturer Product Name Product Type LPCB 

Certificate 

Number 

Ascot Doors 

Limited 







Benw eldSecure Bew dley doorset Single leaf outw ard 


Pow ershield Pow ershield Class Single leaf outw ard 

Doors Limited 3 single 


Selectaglaze 

Limited 

Professional 

Barriers Limited 

Ascot Doors 

Limited 

Pow ershield 

Doors Limited 

Pow ershield Class 

3 double 



Security 

Rating 




Systems 

Active Leaf Passive 

Leaf 

N/A 

131d/04 3 12, 13, 15, 

16, 18 and 

19 

131d/05 3 12, 13, 15, 

16, 18 and 

19 

34, 35 and 

36 

746a/01 3 1 N/A 

852a/01 3 2 to 11, 

13,16,17 and 

19 

N/A 

852a/02 3 2 to 11, 32 

13,16,17 and 

19 

683a/06 3 N/A N/A 

Series 55’ level 3’ Fixed light security 

w indow 

Extendor Eclipse Collapsible grille 869a/01 3 33 N/A 

Centurion A355 




4 single 


4 double 











131d/01 4 13 N/A 

131d/02 4 13, 16, 19, 

27, 29 and 

31 

131d/03 4 13, 16, 19, 

27, 29 and 

31 

852a/03 4 3, 5, 7, 9, 10, 

13, 16, 19, 

20, 21, 22, 

23, 24, 26, 

28 and 30 

852a/04 4 3, 5, 7, 9, 10, 

13, 16, 19, 

20, 21, 22, 

23, 24, 26, 

28 and 30 

N/A 

34, 35 and 

36 

N/A 

32 

Compatible Locking Systems for Products Compatible with the Securiclad Security Panel System 

20 Nov 2011 461



Compatible 

Locking 

Systems 

1 Assa 9787 Single point mortice 

hook lock 

2 MICO 942-3L EPC INT 

AD / HSCH 3 


AD 

4 MICO 942-3 EPC INT 

MD / HSCH 3 


MD 

6 MICO 942-3P EPC INT 

MD / HSCH 3 


MD 


MD / HSCH 3 

Model Type Operation Com patible 

Cylinders 

Entry 

Exit 


system w ith 

automatic 

deadlocking 


system w ith 

automatic 

deadlocking 

Key 

Europrofile 


the HSCH 3 



None 

3-w ay locking Europrofile 

system w ith manual cylinder w ithin 

deadlock 

the HSCH 3 



3-w ay locking None 


deadlock 



deadlock 

the HSCH 3 





deadlock 



deadlock 

the HSCH 3 



Key via an Assa 

256 (Assa 

Classic) 

combined 

cylinder ring and 

thumbturn 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Europrofile 

cylinder 

(key:key)and 

lever handle 

Europrofile 

cylinder 

(key:key) and 


plate 

Europrofile 

cylinder 

(key:key) and 


plate 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Q or R 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 

- 

A, B, C, D, E 

or F 


MD 



deadlock 

10 MICO 942-3L INT AD 3-w ay locking 

system w ith 

automatic 

deadlocking 

None 

Europrofile 

cylinder 

(key:key) and 

lever handle 

Scandinavian 

oval cylinder and 

lever handle 

- 

- 

462 20 Nov 2011

11 MICO 942-3 INT MD / 3-w ay locking Scandinavian Scandinavian G, H, I, J, K, L, 

HSCH 3 

system w ith manual oval cylinder oval cylinder M, N or P 

12 deadlock 

w ithin the HSCH and panic exit G 



13 MICO 942-3 INT MD 3-w ay locking None 


deadlock 

16 MICO 942-3P INT MD 3-w ay locking 


deadlock 

None 

MICO 942-3L INT MD / 3-w ay locking Scandinavian 

HSCH 3 

system w ith manual oval cylinder 

deadlock 




Scandinavian 

oval cylinder 

and panic exit 

push plate 

Scandinavian 

oval cylinder 

and push pad 

14 MICO 942-3P INT MD / 3-w ay locking Scandinavian 

G, H, I, J, K, L, 

HSCH 3 

system w ith manual oval cylinder 

M, N or P 

15 deadlock 


G 



Scandinavian 

oval cylinder 

and push pad 

17 Scandinavian G, H, I, J, K, L, 

oval cylinder M, N or P 

18 and lever handle G 

19 MICO 942-3L INT MD 3-w ay locking 


deadlock 

None 


AD / HSCH 4 


MD / HSCH 4 


MD / HSCH 4 


MD / HSCH 4 


system w ith 

automatic 

deadlocking 

Europrofile 


the HSCH 4 





deadlock 

the HSCH 4 





deadlock 

the HSCH 4 





deadlock 

the HSCH 4 



3-w ay locking Scandinavian 

system w ith oval cylinder 

automatic 


deadlocking 4 cylinder guard 


Scandinavian 

oval cylinder 


Europrofile 

cylinder 

(key:key) and 

lever handle 

Europrofile 

cylinder 

(key:key) and 


plate 

Europrofile 

cylinder 

(key:key) and 

push pad 

Europrofile 

cylinder 

(key:key) and 

lever handle 



- 

- 

- 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

A, B, C, D, E 

or F 

24 MICO 942-3L INT AD / 

Scandinavian G, H, I, J, K, L, 

HSCH 4 

oval cylinder M, N or P 

25 and lever handle G 

20 Nov 2011 463



26 MICO 942-3 INT MD / 3-w ay locking Scandinavian Scandinavian G, H, I, J, K, L, 

HSCH 4 


27 deadlock 

w ithin the HSCH and panic exit G 



28 MICO 942-3P INT MD / 3-w ay locking Scandinavian Scandinavian G, H, I, J, K, L, 

HSCH 4 


29 deadlock 

w ithin the HSCH and push pad G 



30 MICO 942-3L INT MD / 3-w ay locking Scandinavian Scandinavian G, H, I, J, K, L, 

HSCH 4 


31 deadlock 

w ithin the HSCH and lever handle G 




barrel bolts 

33 Extendor Eclipse 

CL03 w ith CL03 


34 MICO 942 2-w ay panic exit 

35 MICO 942P 2-w ay emergency 

36 MICO 942L 2-w ay emergency 

exit device 

- - - 

- Europrofile 


Key (w hen 

internal locking 

S, T or U 

the CL03 cylinder version only) 

guard 

- Panic bar - 

device 

- Push pad - 

exit device 

- Lever handle - 

Compatible Cylinders for Products Compatible with the Securiclad Security Panel System 

Cylinder 

Reference 

Manufacturer Model 

Type 

A Abloy Protec CY304 Double Europrofile cylinder (key:key) 

B Abloy Disclock Pro CY304 Double Europrofile cylinder (key:key) 

C ASSA Tw in 7622 Double Europrofile cylinder (key:key) 

D ASSA C5822 Double Europrofile cylinder (key:key) 

E ASSA 4822 Double Europrofile cylinder (key:key) 

F Kaba Quattro S Euro Double Europrofile cylinder (key:key) 


H ASSA Tw in 7607 Half Scandinavian oval mechanical cylinder 







O Abloy Disclock Pro CY201DP Half Scandinavian oval mechanical cylinder 

464 20 Nov 2011




Q ASSA C5801 Half Scandinavian oval mechanical cylinder 


S ASSA dp4400 Single Europrofile cylinder (key) 

T CISA AP3S Single Europrofile cylinder (key) 

U Kaba Quattro Plus Single Europrofile cylinder (key) 

Notes: 

1. The Securiclad panel systems must be installed in accordance with the approved Securiclad design manual (ISO/SECG04/02/11) and 

compatible product list (ISO/SEC/DSP/15/9/10). 

2. The Security Rating attributed to the compatible product must be at least that of the wall in which it is to be fitted. For example, a 

Security Rating 3 doorset shall not be used to form part of a Security Rating 4 wall. 

3. Refer to notes contained within the relevant certificate/Red Book entries for these products for details of restrictions on their use. 



Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 



Secure Partitioning Systems 

Product 

Name 

Product 

Type 

Minimum 

Height 

(m) 

Lowrey 

Level 1 

Security 

Mesh 

Panel 

System 

Lowrey 

Level 2 

Security 

Mesh 

Panel 

System 

Maximum 

Height 

(m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Security 

Rating 

Partition 0.5 2 3.8 0.5 3 Unlimited N/A N/A 1 974c/01 

walls 1 

formed from 

wall panels 

supported by 

existing 

adjacent 

Partition 0.61 4 3.91 0.5 3 Unlimited 0.5 4.0 1 

walls 1 

formed from 

wall and 

ceiling panels 

supported by 

existing 

adjacent 

Ceiling 

formed from 


N/A N/A 0.5 Unlimited 0.5 4.0 1 


walls 1 

formed from 

wall panels 

supported by 

existing 

adjacent 


walls 1 

formed from 

wall and 


supported by 

existing 

adjacent 

Ceiling N/A N/A 0.5 Unlimited 0.5 4.0 2 

formed from 


Cert. 

No. 

20 Nov 2011 465



Product 

Name 

Lowrey 

Level 3 

Security 

Mesh 

Panel 

System 

Product 

Type 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Security 

Rating 


walls 1 

formed from 

wall panels 

supported by 

existing 

adjacent 


walls 1 

formed from 

wall and 


supported by 

existing 

adjacent 

Ceiling 

formed from 



Cert. 

No. 


Com ponent Type Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Mesh w all panel 0.25 2.4 0.5 1.5 N/A N/A 

Ceiling panel Mesh ceiling panel N/A N/A 0.25 1.5 0.25 3.8 

Support post 

Corner post 

Doorsets 5 





system 



system 





0.5 3.8 0.215 0.215 N/A N/A 

0.5 3.8 0.125 0.125 N/A N/A 

0.5 3.8 0.11 0.11 N/A N/A 

Refer to ‘Low rey Level 1, 2 and 3’ single leaf mesh security doorsets (LPCB 


Refer to ‘Low rey Level 1, 2 and 3’ double leaf mesh security doorsets (LPCB 


Notes: 

1. The walling system can either be constructed as a straight walling system or incorporate 90 or 270 degree angles. This angle is 

measured between the attack faces of the two adjacent panels. 

2. The minimum height of partitioning systems incorporating doorsets is 1.0 m. 

3. The minimum width of walls incorporating doorsets is 0.63 m. 

4. The minimum height of partitioning systems formed with a ceiling and incorporating doorsets is 1.1 m. 

5. The doorsets are not designed to be fitted within the ceiling system 

6. The partitioning system’s resistance relies on the supporting substrate offering compatible resistance to manual attack. 

7. The Lowrey security mesh panel systems are approved when installed in accordance with the instructions detailed in Lowrey’s 


Certificate No: 974f to LPS 1175: Issue 7 

Secure Partitioning Systems 

Product 

Name 

Product 

Type 

Minimum 

Height 

(m) 

Lowrey 

Level 4 

Security 

Solid 

Panel 

System 

Maximum 

Height 

(m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Security 

Rating 

Partition 

formed from 

wall panels 

supported by 

existing 

adjacent 

walls 1 0.5 2 3.8 0.5 3 Unlimited N/A N/A 4 974f/01 

Cert. 

No. 

466 20 Nov 2011



Product 

Name 

Product 

Type 

Partition 

formed from 

wall and 


supported by 

existing 

adjacent 

Minimum 

Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width (m) 

Maximum 

Width (m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

walls 1 0.61 4 3.91 0.5 3 Unlimited 0.5 4.0 4 

Ceiling 

formed from 


Security 

Rating 


Cert. 

No. 



Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Solid w all panel 0.25 2.4 0.5 1.5 N/A N/A 

Ceiling panel Solid ceiling panel N/A N/A 0.25 1.5 0.25 3.8 

Support post 

Corner post 

Doorsets 6 



270 degree 

corner post for 




system 

Single leaf 



Double leaf 



0.5 3.8 0.215 0.215 N/A N/A 

0.5 3.8 0.125 0.125 N/A N/A 

0.5 3.8 0.11 0.11 N/A N/A 

Refer to ‘Low rey Level 4’ single leaf security doorsets (LPCB Ref. No. 


Refer to ‘Low rey Level 4’ double leaf security doorsets (LPCB Ref. No. 


Notes: 

1. The walling system can either be constructed as a straight walling system or incorporate 90 or 270 degree angles in the wall line. This 

angle is measured between the attack faces of the two adjacent panels. 



4. The minimum height of partitioning systems formed with a ceiling and incorporating doorsets is 1.1 m. 

5. The doorsets are not designed to be fitted within the ceiling system. 


7. The Lowrey security solid panel systems are approved when installed in accordance with the instructions detailed in Lowrey’s 


MultiSteel Limited 

MultiSteel House, 117-119 Brent Terrace, London NW2 1LL, United Kingdom 

Tel: +44 (0)20 8208 8300 • Fax: +44 (0)20 8208 8209 

E-mail: office@multisteel.co.uk • Website: www.multisteel.co.uk 


20 Nov 2011 467



Modular Security Screen 


Structural 

Opening 

Height 

(m) 

Multisteel 'Security 

Screen' 

Maximum 

Structural 

Opening 

Height 

(m) 

Minimum 

Structural 

Opening 

Width 

(m) 

Maximum 

Structural 

Opening 

Width 

(m) 

Security 

Rating 

Modular security 1.9 5 0.79 4 1 818b/01 

doorset 2, 3 

screen 1 

with access control 

Modular security 1.9 5 0.7 4 2 

doorset 4 

screen 1 

with deadlocking 

Modular security 

screen 5 1.9 5 2 6 2 

Cert. 

No. 

Notes 

1. The security screens are available with glazed and opaque panels. 

2. The access control system’s resistance to “non-mechanical” attack has not been assessed as it is outside the scope of 

LPS 1175. It is therefore recommended that specifiers satisfy themselves that the components used are resistant to any 

environmental conditions/interference that may cause the locking system to disengage. 

3. Refer to LPCB certificate number 818a for full details of the Multisteel ‘Mag Lock’ doorset (LPCB reference number 

818a/01). 

4. Refer to LPCB certificate number 818a for full details of the Multisteel ‘3 Point Mul-T-Lock’ doorset (LPCB reference 

number 818a/02). 

5. This configuration does not incorporate any doorsets. 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 


Certificate No: 450k to LPS 1175: Issue 7 

Secure Partitioning System 

Product Name Product 

Type 

Minimum 

Height 

(m) 

Ultrasecure 

security mesh 

panel system 

Walling 

system 

Ceiling 

system 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 

Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Security 

Rating 

Cert. 

No. 

0.50 1 6 0.50 2 Unlimited N/A N/A 3 450k/01 

N/A N/A 0.50 Unlimited 0.50 6 3 


468 20 Nov 2011


Height 

(m) 

Maximum 

Height 

(m) 

Minimum 

Width 

(m) 

Maximum 

Width 

(m) 



Minimum 

Length 

(m) 

Maximum 

Length 

(m) 

Wall panel Mesh wall panel 0.50 6 0.25 1 N/A N/A 

Ceiling panel Mesh ceiling panel N/A N/A 0.25 1 0.50 6 

Support post 

Corner post 

Doorsets 

Notes 


walling system 3 0.46 5.91 0.165 0.165 N/A N/A 

Corner post for 

0.50 6 0.13 0.13 N/A N/A 

walling system 3 

Single leaf outward Refer to Ultrasecure SCD1 mesh security doorset (LPCB Ref. No. 




450j/01) for scope of approval 4 . 

Refer to Ultrasecure SCD2 mesh security doorset (LPCB Ref. No. 

450j/02) for scope of approval 4 . 



3. The walling system can either be constructed as a straight walling system or incorporate 270 degree angles in the wall line. This 

angle is measured between the attack faces of the two adjacent panels. 

4. The doorsets are not designed to be fitted within the ceiling system. 


6. The Ultrasecure security cage system is approved when installed in accordance with the instructions detailed on document SCS- 

DV-3-FIT-01 (Ref.B). 



Tel: +44 (0)1429 867 388 • Fax: +44 (0)1429 867 355 



Secure Partition Wall Systems 


Wall 

Height 

(m) 

Securilath HD1 

Partition wall 

Standard 

system 

Securilath HD1-PB Partition wall 

system 

Securilath MD1 

Partition wall 

system 

Securilath HD1 Twin Partition wall 

system 

Maximum 

Wall 

Height 

(m) 

Minimum 

Wall 

Width 

(m) 

Maximum 

Wall 

Width 

(m) 

Security 

Rating 2 

Cert. 

No. 

1.2 3.0 0.6 N/A 1 2 731b/01 

1.2 3.0 0.6 N/A 1 1 731b/02 

1.2 3.0 0.6 N/A 1 1 731b/03 

1.2 3.0 0.6 N/A 1 3 731b/04 

Approved Configurations 

20 Nov 2011 469



System Layers Configuration Approved Installation 

Instructions 

Securilath 

HD1 Standard 

Attack face 19 mm thick plyw ood fixed using 4.5 mm by 50 mm 

w oodscrew s at 300 mm centres. 

‘HD1 Securilath’ mesh panels fixed to timber studs using 

65 mm by 3.35 mm bright annular nails to BS1202 w ith R36 

w ashers at maximum 400 mm centres. 

Securilath 

HD1-PB 

Securilath 

MD1 

Securilath 

HD1 Tw in 

Timber stud 

Non- Attack 

face 

Attack face 

Timber stud 

Non- Attack 

face 

Attack face 

Timber stud 

Non- Attack 

face 

Attack face 

Timber stud 

Non- Attack 

face 

75 mm by 50 mm softw ood frame w ith vertical studs at 

600 mm centres. Noggins shall be at maximum 400 mm 

centres. Timber fixed w ith M8 by 80 mm screw s. 

12 mm thick plasterboard fixed using bugle head dryw all 

screw fixings PN2 3.5 mm by 55 mm BZP at maximum 450 

mm centres. 



mm centres. 









mm centres. 

19 mm thick plyw ood fixed using 4.5 mm by 50 mm 


‘MD1 Securilath’ mesh panels fixed to timber studs using 








mm centres. 














Securilath Installation Guide 

IP90 LPCB Inst. Issue 6, April 

2011 



2011 



2011 



2011 

Notes: 

1. There is no restriction on the maximum width as long as the partition wall is constructed in a straight run and does not include any 

corners. 

2. These systems are approved as plain partitions. Please refer to the introduction to the section on secure walling systems in Red Book 

Volume 2 for further information. 

470 20 Nov 2011


SECURE ROOFING SYSTEMS 

Roofing systems listed in this section are approved to LPS 1175 Requirements and testing procedures for the 



In order to comply with the terms of the approval, the roofing systems should be designed and installed in 

accordance with the relevant system manuals noted within the product entry. The styles of tile/panel included 

within the scope of approval, the range of roof pitches to which they can be fitted and the accessories that are 

covered by the scope of approval are also noted in each product entry. 

Icopal S. A. 

Parc Industriel des Hauts Sarts, Rue de Hermee 186, Herstal, Belgium 

Tel: +32 4240 5151 • Fax: +32 4240 5199 

E-mail: sales@decra.co.uk • Website: www.decra.co.uk 

UK sales, marketing, distribution and technical enquiries: 

Decra Roofing Systems Limited, Unit 4, Crompton Fields, Crompton Way, Crawley, West Sussex RH10 9QB, 

United Kingdom 

Tel: +44 (0)1293 545058 • Fax: +44 (0)1293 562709 



Security Roof Tiling Systems 

Product Name 

Overall Tile 

Tile Cover 

Security 

Cert. No. 

Size (mm) 

(mm) 

Rating 

Decra Classic 1324 x 410 1260 x 370 1 834a/01 

Decra Stratos 1290 x 360 1230 x 320 1 834a/02 

Decra Elegance 1324 x 410 1260 x 370 1 834a/03 

Decra Plus 1324 x 410 1260 x 368 1 834a/04 

Approved Configurations 

System Roof pitch Tile bond 

configurations 

Batten size to be used according to the maximum rafter 

spacing (mm) 

Staggered Straight 450 600 900 1200 1500 

Decra 10° to 90° 38 x 25 50 x 25 50 x 50 50 x 50 50 x 65 

Classic 

Decra 10° to 90° - 38 x 38 50 x 38 50 x 50 50 x 50 50 x 65 

Stratos 

Decra 10° to 90° 38 x 25 50 x 25 50 x 50 50 x 50 50 x 65 

Elegance 

Decra Plus 10° to 90° 38 x 25 50 x 25 50 x 50 50 x 50 50 x 65 


20 Nov 2011 471


SECURE ROOFING SYSTEMS 

Accessory Decra Classic Decra Elegance Decra Stratos Decra Plus 

Cloaked verge cap – Left hand DH_B2 EH_B2 - - 

Cloaked verge cap – Right hand DI_B2 EI_B2 - - 

Barge cover – Left hand DH_B1 - SH_B1 - 

Barge cover – Right hand DI_B1 - SI_B1 - 

Barge cover eaves closure – Left DH_DE1 - SH_DE1 - 

hand 

Barge cover eaves closure – Right DI_DE1 - SI_DE1 - 

hand 

Top course DC_B1 EC_B1 DC_B1 DC_B1 

Decra Plus D box barge cap - - - PH_D1 

Decra Plus D ridge/hip sealing strip - - - PSXD1 

D ridge hip end closure unit DD_DH1 ED_DH1 DD_DH1 DD_DH1 

D ridge DD_B1 ED_B1 DD_B1 PD_D1 

D ridge end closure unit DD_DE1 ED_DE1 DD_DE1 DD_DE1 

In-line air vent DVA_W1 EVA_W1 SVA_W1 DVA_W1 

In-line soil/mech extract vent DVS_W1 EVS_W1 SVS_W1 DVS_W1 

Universal D ridge/hip ventilator DVUXW1 DVUXW1 DVUXW1 DVUXW1 

Decra Classic D ridge vent filler DVRXW1 DVRXW1 - - 

Finishing kit DU_B1 EU_B1 DU_B1 DU_B1 

Fixing nails (6kg) pack DNXB5 DNXB5 DNXB5 DNXB5 

Decra power tile fixing nails DNXP7 DNXP7 DNXP7 - 

Approved System Instructions 

This approval covers the above roof tiling systems when designed and installed in accordance with the following instructions. 

System Instructions 

Decra Classic Decra Classic tile Secured by Design instructions (October 2007) 

Decra Stratos Decra Stratos tile Secured by Design instructions (October 2007) 

Decra Elegance Decra Elegance tile Secured by Design instructions (October 2007) 

Decra Plus Decra Plus tile Secured by Design instructions (October 2007) 

Notes 

1. This approval assumes the roofing systems are installed to roof structures of equivalent resistance to attack. 

2. This approval covers the roofing systems when installed in the ‘unsupported underlay’ configuration. 

472 20 Nov 2011


PERIMETER SECURITY PRODUCTS 

This section lists perimeter security products; such as fences, gates and turnstiles; that have been approved 

to LPS 1175 Requirements and testing procedures for the LPCB approval and listing of intruder resistant 

building components, strongpoints, security enclosures and free-standing barriers. 

While previous versions of the standard specified six levels of resistance (security ratings), the latest version 

(Issue 6 and 7) specifies eight security ratings. The levels of risk on which the security ratings are based in 

Issue 6 and 7 are represented in the following chart. 

HIGH RISK 

LPS 1175 SR 8 

LPS 1175 SR 7 

LPS 1175 SR 6 

LPS 1175 SR 5 

LPS 1175 SR 4 

LPS 1175 SR 3 

LPS 1175 SR 2 

LOW RISK LPS 1175 SR 1 

Products certified to this standard provide 20 minutes of 

resistance to extreme means of attempting forced entry into 

higher value storage areas. 

Products certified to these standards provide 10 minutes of 

resistance to professional means of attempting forced entry into 

higher value storage areas using a wide range of tools including 

mains powered tools. 

Products certified to these standards resist experienced 

attempts at forced entry using a wide range of tools including 

battery powered tools lasting up to 10 minutes (SR 4 and 5) or 

5 minutes (SR 3). 

Products certified to this standard provide 3 minutes of 

resistance to determined attack by an opportunist burglar using 

a range of techniques including those that involve creation of 

noise. 

Products certified to this standard provide 1 minute of 

resistance to opportunist attempts at entry using a range of 

techniques including those that create noise such as those 

involving breaking glass. 

LPS 1175 supports the assessment, approval and specification of perimeter security products such as walls, 

fences, gates and turnstiles. 

Unlike current British and European fence standards, LPS 1175 is based on manual attack testing with the 

resistance provided by the products measured in terms of the attack tools and time available to the attacker. It 

enables specifiers to select products according to their performance relative to the risks faced rather than 

simply specifying them by design. 

Although the standard includes minimum requirements relating to the height of the product, the product’s 

resistance to scaling is not covered by the standard, nor is its resistance to tunnelling or vehicle impact. 

Further information on the security rating system and attack tools can be found in the standard itself, which 

can be downloaded from the Red Book web site www.RedBookLive.com. 

For details of products offering resistance to vehicle impact, please refer to Section 2.10. 


When selecting a perimeter security product, it is important to note aspects such as the size, locking systems 

and directions of opening; all can affect the level of security provided by the product. These aspects of each 

certified product have therefore been described to enable selection of the most appropriate product. 

It is important to ensure that the products are installed in accordance with the manufacturer’s instructions and 

that all exposed fixings, the substrate into which the device is fitted and the locking mechanisms are regularly 

checked to ensure that they are in good condition and that they have not been tampered with. 

20 Nov 2011 473


PERIMETER SECURITY PRODUCTS 

Unless otherwise stated, the security ratings attributed to the products listed require all locks to be fully 

engaged. 

474 20 Nov 2011


SECURITY FENCING 

CLD Fencing Systems 

Unit 11, Springvale Business Centre, Millbuck Way, Sandbach, Cheshire CW11 3HY, United Kingdom 

Tel: +44 (0)1270 764751 • Fax: +44 (0)1270 757503 

E-mail: info@cld-fencing.com • Website: www.cld-fencing.com 


Security Fencing Systems 

Product 

Type 

Name 

Securus 

SR1 

Securus 

SR2 

Nominal 

Height (m) 

Maximum 

Post 

Centres (m) 

Gradients 

Angles in 

Fence Line 

Welded mesh security 

fencing system 1 2.4 2.515 0°, 9.5° and 

18.4° 4 100° to 

170°, 180°, 

190° to 

260°, 270° 

Vertical bar and mesh panel 2.4 2.515 0°, 9.5° and 

security fencing system 2 18.4° 

100° to 

170°, 180°, 

190° to 

260°, 270° 

Security 

Rating 

Cert. 

No. 

1 999a/01 

2 999a/02 

Principle Components 5 

Component Type Description Securus Fencing System 

Base-plated 

posts 

Embedded 

posts 

Panels 

Clamping bars 

Reinforcing 

channels 

Base-Plated 

Version 

Primary posts Pow der coated steel posts. 

Embedded 

Version 

SR2 

Embedded 

Version 

Corner posts Pow der coated steel posts 

used to form angles in the 

fence line. 

100° to 170° 

190° to 260° 

270° 

Primary posts Pow der coated steel posts. 

Intermediate posts 

Corner posts 

Galvanised mesh 

panels 

Clamp bars 

Intermediate clamp 

bars 

Channel 

Approved Assembly and Installation Drawings 

Pow der coated steel 

intermediate posts. 

Pow der coated steel posts 

used to form angles in the 

fence line. 

‘Security 358’ w elded mesh 

panels. 

Clamping bars secured over 

the mesh to the attack face of 

each post. 

Clamping bars secured over 

the mesh to the attack face of 

each intermediate post. 

Channels secured over the 

mesh to reinforce it. 

100° to 170° 

190° to 260° 

270° 

 

100° to 170° 

190° to 260° 

270° 

One layer One layer Tw o layers 

 

SR1 

 

 

 

20 Nov 2011 475



Document Ref. Revision / 

Issue Date 

SR1/07/Bas 

(Draw ing 1 of 5) 

SR1/07/Bas 


SR1/07/Bas 


SR1/07/Bas 


SR1/07/Bas 


SR1/07/Fou 


SR1/07/Fou 


SR1/07/Fou 


SR1/07/Fou 


SR1/07/Fou 


SR2/07/Fou 


SR2/07/Fou 


SR2/07/Fou 


SR2/07/Fou 


SR2/07/Fou 


Revision 7 

12/01/11 

Revision 7 

12/01/11 

Revision 7 

12/01/11 

Revision 7 

12/01/11 

Revision 7 

12/01/11 

Revision 6 

06/12/10 

Revision 6 

06/12/10 

Revision 6 

06/12/10 

Revision 6 

06/12/10 

Revision 6 

06/12/10 

Revision 5 

13/12/10 

Revision 5 

13/12/10 

Revision 5 

13/12/10 

Revision 5 

13/12/10 

Revision 5 

13/12/10 

Title / Contents 

General assembly 

Elevations detail 

Installation instructions 

Component details 

Variable angle details 











Base-Plated 

Version 

 

 

 

 

 

Securus Fencing System 

SR1 

Embedded 

Version 

 

 

 

 

 

SR2 

Embedded 

Version 

 

 

 

 

 

Notes: 

1. The fencing system is available in configurations to suit either surface mounting onto hard surfaces 3 or embedding within concrete 

foundations placed in the ground 3 . 

2. The fencing system is available in configurations to suit embedding within concrete foundations placed within the ground 3 only. 

3. It is important to ensure that the local ground onto/into which the fence is installed offers compatible strength and that the fence is 

installed in accordance with the documents listed in the table entitled ‘Approved assembly and installation drawings’. 

4. The base-plated version of the ‘Securus SR1’ fencing system is not approved for use on 18.4° gradients. 

5. The fencing system should only be constructed using components supplied by CLD Fencing Systems. 

6. The ‘angles in fence line’ define the range of angles covered by the scope. These are measured between the attack faces of two 

adjacent fence panels. 

H S Jackson & Son (Fencing) Limited, t/a Jacksons Fencing 

Stowting Common, Ashford, Kent TN25 6BN, United Kingdom 

Tel: +44 (0)1233 750393 • Fax: +44 (0)1233 750178 

E-mail: security@jacksons-fencing.co.uk • Website: www.jacksons-fencing.co.uk 


Security Fencing System 

Product 

Name 

Type Height (m) Post 

Centres (m) 

Gradients 

Jakoustic Timber security 2.5, 2.75, 3.0 0.125 to 2.4 0° to 

Class 3 fencing system 1 or 3.25 

18.5° 

Angles In 

Fence Line 

90°, 180° or 

270° 

Security Cert. 

Rating No. 

3 913a/01 

476 20 Nov 2011




Component Type Description 

Timber Boards Timber acoustic boards – Mid section 142.75 mm by 34 mm by 4800 mm long timber 

tongue and groove board. 

Timber acoustic boards – Base 

section 

142.75 mm by 34 mm by 4800 mm long timber 

tongued board. 

Timber acoustic boards – Top section 123 mm by 34 mm by 4800 mm long and /or 48 

mm by 34 mm by 4800 mm long timber grooved 

board. 

Posts 

Intermediate and corner posts 152 mm by 89 mm by 16 mm universal beam 

either 3350 mm, 3600 mm, 3850 mm or 4100 

mm long to suit fence height. 

Timber batten for steel post 

100 mm by 50 mm timber batten either 2700 mm, 

2950 mm, 3200 mm or 3450 mm long to suit post 

height. 

Capping Rail Timber capping rail 145 mm by 34 mm by 4800 mm long timber 

section. 

Counter Rail Timber counter rail 70 mm by 34 mm by 2400 mm long timber 


Post Cover Boards Timber post cover board 125 mm by 34 mm by 3200 mm long timber 

board. 

Corner Supports Timber corner support 54 mm by 45 mm by 3200 mm long timber 


Timberlok Screws Steel screws 100 mm and 150 mm long galvanised steel 

screw. 

2, 3, 4 


Document Ref. Revision / Issue Date Title / Contents 

09 HS1/1001 (Sheet 1 of 3) 0.1 05/01/10 Jakoustic Class 3 fencing general detail 

09 HS1/1001 (Sheet 2 of 3) 0.1 05/01/10 Jakoustic Class 3 fencing general detail 

09 HS1/1001 (Sheet 3 of 3) 0.1 05/01/10 Jakoustic Class 3 fencing raking detail 

Notes 

1. The fencing system should only be constructed using components supplied by Jacksons Fencing. 

2. It is important to ensure the local ground onto/into which the fence is installed offers compatible strength and that the fence is 

installed in accordance with the documents listed the table entitled ‘Approved assembly and installation drawings’. 

3. The fencing system is approved for installation onto/into flat ground of gradients between 0° and 18.5°. 


adjacent fence posts. 



Product 

Name 

Type 

Height 

(m) 

Post 

Centres 

(m) 

Trident 4 Vertical bar and mesh panel security 3.6 0.260 to 

fencing system 1 2.57 

Trident 5 Vertical bar and mesh panel security 4.2 0.260 to 

fencing system 1 2.57 

Gradients 

Angles in 

Fence Line 

0° to 5.7° 90°, 180° or 

270° 

0° to 5.7° 90°, 180° or 

270° 

Security 

Rating 

Cert. 

No. 

4 913b/01 

5 913b/02 


20 Nov 2011 477




Panels Galvanised vertical bar and mesh 

panels 

Fence panels comprising of reinforced 3/8” tubular vertical bars 

welded within 60 mm by 40 mm horizontal rails. The panels 

incorporate ‘358’ mesh panels welded on either face. 

Posts Galvanised steel posts 120 mm by 120 mm by 5 mm galvanised steel post. 

Toppings Concertina barbed tape topping 800 mm diameter barbed tape topping 

Document Ref. 

Approved Assembly and Installation Drawings 2, 3, 4 Trident 4 Trident 5 

Revision / Issue 

Date 


Product Name 

09 HS1_1002 

(Sheet 1 of 5) 

09 HS1_1002 


09 HS1_1002 


09 HS1_1002 


09 HS1_1002 


Revision 0.2 

30/03/10 

Revision 0.2 

30/03/10 

Revision 0.2 

30/03/10 

Revision 0.2 

30/03/10 

Revision 0.2 

30/03/10 

09 HS1_1003 


Revision 0 

31/03/10 

09 HS1_1003 Revision 0 

(Sheet 2 of 5) 31/03/10 


(Sheet 3 of 5) 31/03/10 


(Sheet 4 of 5) 31/03/10 


(Sheet 5 of 5) 31/03/10 

HS1_4001 Revision 0.0 

31/03/2010 

3.6 m high Trident 4 fencing general layout 

3.6m Trident 4 sections, details and notes 

3.6m high Trident 4 fencing stepped using standard 

components 

3.6m high Trident 4 fencing stepped using double 

posts 

3.6m high Trident 4 fencing stepped using special 

stepped posts 

4.2 m high Trident 5 fencing general layout 

4.2 m Trident 5 sections, details and notes 

4.2 m high Trident 5 fencing stepped using 

standard components 

4.2m high Trident 5 fencing stepped using double 

posts 

4.2m high Trident 5 fencing stepped using special 

stepped posts 

Concertina barbed tape topping option for trident 

fencing range 

 

 

 

 

 

Notes 

1. The fencing system should only be constructed using components supplied by Jacksons Fencing. 


installed in accordance with the documents listed the table entitled ‘Approved assembly and installation drawings’. 




Heras U.K. Fencing Systems 

Herons Way, Balby, Doncaster DN4 8WA, United Kingdom 

Tel: +44 (0)1302 364551 • Fax: +44 (0)1302 322401 

E-mail: enquiries@herasuk.co.uk • Website: www.heras.co.uk 



Product Name Type Height (m) Post 

Centres 

(m) 

Contour Standard 

Capped 

Gradients 

Angles In 

Fence Line 1 

Railings 1.8, 2.0 and 2.4 2.84 16.5° 3 75° to 105°, 

165° to 195° 

and 

255° to 265° 

Security 

Rating 

Cert. 

No. 

1 890a/01 

478 20 Nov 2011



Product Name Type Height (m) Post 

Centres 

(m) 

Contour Mitred 

Top 

Contour Security 

Capped 

Contour Security 

Mitred Top 

Contour Fullered 

Top 

Gradients 

Angles In 

Fence Line 1 


165° to 195° 

and 

255° to 265° 

Railings 1.8, 2.0 and 2.4 2.755 17° 3 75° to 105°, 

165° to 195° 

and 

255° to 265° 

Railings 1.8, 2.0 and 2.4 2.755 17° 3 75° to 105°, 

165° to 195° 

and 

255° to 265° 


165° to 195° 

and 

255° to 265° 

Contour Point Top Railings 1.8, 2.0 and 2.4 2.84 16.5° 3 75° to 105°, 

165° to 195° 

and 

255° to 265° 

Contour Square 

Bar Capped Top 

Pallas Xtra 

Zenith 


165° to 195° 

and 

255° to 265° 

Welded mesh 

security fencing 

system 

Welded mesh 

security fencing 

system 

1.8, 2.0 and 2.4 2.53 0° 2 175° to 185° 

and 

265° to 275° 

1.8, 2.0, 2.4, 

3.0, 4.2 and 5.2 

2.44 0° 2 175° to 185° 

and 

265° to 275° 

Security 

Rating 

Cert. 

No. 

1 890a/02 

1 890a/03 

1 890a/04 

1 890a/05 

1 890a/06 

1 

1 890a/08 

1 890a/09 

Principle Components (Contour Fencing Systems) 4 


Contour 

Standard 

Capped 

Finials 

Fishplates 

Contour 

Mitred 

Top 

Fencing System 

Contour 

Security 

Mitred 

Top 

Contour 

Security 

Capped 

Contour 

Fullered 

Top 

Contour 

Point 

Top 

Fullered Fullered finial 

Point Point top finial 

Intermediate 

fishplate 

Corner 

fishplate 

Square 

Bar 

Capped 

Top 

Fishplate used 

to attach rails to 

intermediate 

posts. These 

form angles in 

the fence 

between 165° 

and 195° 1 

Fishplate used 

and 265° 1 

to attach rails to 

intermediate 

posts. These 


the fence 

between 75° 

and 105° and 

between 255° 

20 Nov 2011 479



Pales 

Posts 

Rails 

Standard 

capped 

pales 

Standard 

mitred pales 

25.5 mm (outer 

diameter) steel 

tubes at 

0.125 mm 

centres 



tubes at 

0.125 mm 

centres 

TR300 pales 25.5 mm (outer 


tubes at 

0.125 mm 

centres 

Security 

capped 

pales 

Security 

mitred pales 

Square bar 

capped 

pales 

HD rolled 

formed 

posts 

HD1 rails 

HD2 rails 

HD3 rails 



tubes at 

0.103 mm 

centres 



tubes at 

0.103 mm 

centres 

25 mm by 

25 mm steel 

tubes at 

0.125 mm 

centres 

HD rolled 

formed post of 

nominal cross 

section 117 mm 

by 43.5 mm 

55 mm by 

52 mm by 

1.5 mm rail 

55 mm by 

52 mm by 

1.5 mm rail 

55 mm by 

52 mm by 

1.5 mm rail 

 

 

 

 

 

 

 

 

 

 

Principle Components (Pallas Xtra and Zenith Fencing Systems) 4 

Component Type Description Fencing 

Pallas System Zenith 

Xtra 

Panels Pallas Xtra welded 

mesh panels 

Welded mesh formed from nominal 6 mm diameter steel 

vertical wires at 50 mm centres and pairs of 8 mm diameter 

horizontal wires at 200 mm centres 

 

Zenith welded mesh 

panels 

Welded mesh formed from nominal 4 mm diameter steel 

wires at 76.3 mm (3 inch) vertical centres and 12.7 mm (1/2 

inch) horizontal centres 

 

480 20 Nov 2011



Panel clamp 

bars 

Posts 

Hexafix clamp bars 

Zenith clamp bars 

Hexafix RHS 

intermediate posts 

Hexafix RHS corner 

posts 

Zenith intermediate 

posts 


posts 


posts 


posts 

Zenith corner posts 



40 mm by 5 mm slotted steel clamp bars secured using M8 

by 40 mm shear drive bolts 

40 mm by 5 mm slotted steel clamp bars secured using M8 

cup square bolts and shear nuts 

60 by 40 mm by 3 mm RHS posts with integral panel 

mounting clips 

60 by 60 mm by 2 mm SHS posts with integral panel 

mounting clips 

60 by 60 mm by 2 mm SHS posts for use on 1.8 m, 2.0 m 

and 2.4 m high fences 

80 by 40 mm by 3 mm RHS posts for use on 3.0 m high 

fences 

80 by 80 mm by 3 mm RHS posts for use on 4.2 m high 

fences 

100 by 100 mm by 4 mm SHS posts for use on 5.2 m high 

fences 

60 by 60 mm by 2 mm SHS posts for use on 1.8 m, 2.0 m 

and 2.4 m high fences 

80 by 80 mm by 3 mm RHS posts for use on 3.0 m and 4.2 m 

high fences 

100 by 100 mm by 4 mm SHS posts for use on 5.2 m high 

fences 

U clamp sets U- clamp set Three U-clamp sets comprising 5 mm diameter steel U- 

clamps, plastic bases, steel retaining plates, M6 shear nuts 

and plastic covers 

Approved Assembly and Installation Drawings (Contour, Pallas Xtra and Zenith Fencing Systems) 5 

 

 

 

 

 

 

 

 

 

 

 

 

Document 

Ref. 

Form 39 0 

7/7/10 

Form 40 0 

11/11/10 

Form 42 

(Contour 

Capped/ 

Mitred/ 

Square Bar) 

Form 42 

(Contour 

Finial Top) 

Form 42 

(Contour 

Security 

Capped/ 

Mitred Top) 

Revision / 

Issue Date 


Customer information 

(Zenith) 

Customer information 

(Pallas Xtra) 

11/11/10 Customer information 

(Contour Capped / 

Mitred / Square Bar) 


(Contour Point Top / 

Fullered Top) 


(Contour Capped / 

Mitred / Square Bar) 

Pallas 

Xtra 

 

Zenith 

 

Fencing System 

Contour 

Standard 

Capped 

and 

Contour 

Mitred 

Top 

 

Contour 

Security 

Capped 

and 

Contour 

Security 

Mitred 

Top 

 

Contour 

Point Top 

and 

Contour 

Fullered 

Top 

 

Square 

Bar 

Capped 

Top 

 

20 Nov 2011 481



ref_pal_1 

B 

11/11/10 

Pallas Xtra 

specification 1.8m, 

2.0m, 2.4m high fence 

installation details 

 

ref_pal_3 0 

19/3/09 

ref_zen_1 

A 

11/11/10 

ref_zen_3 0 

16/3/09 

Hexafix system 

External corner 

assembly 

Zenith system 

specification 

All heights 

Installation details 

Zenith system in 

ground spec corner 

arrangement 

 

 

 

Notes 



2. The fencing system is only approved for installation into flat level ground. 

3. The gradient is based on a maximum rake of 800 mm along the length of the rail. It relates to the 2.0 m and 2.4 m high fences. The 

scope of approval for the 1.8 m high fences only covers fences installed on flat level ground. 

4. The fencing system should only be constructed using components supplied by Heras U.K. Fencing Systems. 

5. The fencing system is approved for installation into foundations buried in the ground, as detailed on the documents listed in the 

table above entitled ‘Approved Assembly and Installation Drawings’. The approval does not cover the use of base plated posts 

surface mounted on top of the ground. 

6. It is important to ensure the local ground onto/into which the fence is installed offers compatible strength. 

NK Fencing Limited 

40 Trailcock Road, Carrickfergus, Co. Antrim, Northern Ireland BT38 7NU, United Kingdom 

Tel: +44 (0)28 9335 1172 • Fax: +44 (0)28 9336 4336 

E-mail: mail@nkfencing.com • Website: www.nkfencing.com 



Product 

Type 

Name 

Ibex Hi Welded mesh security 

Security fencing system 

Height 

(m) 

Post Centres 

(m) 

Gradients 

1.8 to 3 1 to 2.46 0° to 

5.71° 

Angles in Security Cert. 

Fence Line Rating No. 

90° to 315° 1 951a/01 

Principal Components 

Component Type Description Ibex Hi Security Fencing 

System 

Panels 

Pre-galvanized welded 

mesh panels 

Galvanized welded mesh formed 

from nominal 4 mm diameter steel 

vertical and horizontal wires at 

76.2 mm and 12.7 mm centres 

respectively 

Base-plated 

version 

 

Standard 

(Embedded 

version) 

 

482 20 Nov 2011

Base-plated Posts NK Ibex Hi-Security 

standard post 

assembly 

NK Ibex Hi-Security 

end post assembly 


alternative end post 

assembly 

Hot dip galvanized steel 

intermediate post 

Hot dip galvanized steel post 

Hot dip galvanized steel post used 

to form the end of the fence line or 

used in pairs to form acute and 

obtuse angles in the fence line 



180° 

 

>90° to 180° to 270° to 315° 

Embedded Posts 


corner post assembly 


standard post 

assembly 


end post assembly 


to form right angles in the fence 

line 

Hot dip galvanized steel 

intermediate post 


to form the end of the fence line or 

used in pairs to form acute and 

obtuse angles in the fence line 

270° 

180° 

>90° to 180° to 270° to 315° 

Panel clamping 

bars 


corner post assembly 

Stretcher bar 


to form right angles in the fence 

line 

Clamping bars secured to the 

attack face of each post 

 

270° 

 


Drawing No. 

/ Sheet 

1096M (Sheet 

22) 

1096M (Sheet 

23) 

1096M (Sheet 

24) 

1096M (Sheet 

25) 

1096M (Sheet 

26) 

1096M (Sheet 

27) 

1096M (Sheet 

28) 

Revision / 

Issue Date 


18/08/09 1.8-3.0 Ibex security fence (base plated 

posts) - Fence general arrangement 

Rev A 1.8-3.0 Ibex security fence (base plated 

02/09/09 posts) - Fence general arrangement for 

sloping ground (Option A - Panels above 

ground level) 


posts) - Fence general arrangement for 

sloping ground (Option B - Buried panel 

bases) 

Rev B 

08/09/09 

1.8-3.0 Ibex security fence (base plated 

posts) - Fence erection details (Exploded 

views and sections at posts) 


posts) - Fence erection details (Plan views) 


posts) - Panel detail 

Rev A 1.8-3.0 Ibex security fence (base plated 

08/09/09 posts) - Post and stretcher bar detail 

Ibex Hi Security Fencing 

System 

Base-plated 

version 

 

 

 

 

 

 

 

Standard 

(Embedded 

version) 

20 Nov 2011 483



1096M (Sheet 

29) 

1096M (Sheet 

30) 

1096M (Sheet 

31) 

1096M (Sheet 

32) 

1096M (Sheet 

33) 

1096M (Sheet 

34) 

1096M (Sheet 

35) 

Notes 

18/08/09 1.8-3.0 Ibex security fence (buried posts) - 

Fence general arrangement 

Rev A 1.8-3.0 Ibex security fence (buried posts) - 

02/09/09 Fence general arrangement for sloping 

ground (Option A - Panels above ground 

level) 


Fence general arrangement for sloping 

ground (Option B - Buried panel bases) 

Rev B 

08/09/09 

1.8-3.0 Ibex security fence (buried posts) - 

Fence erection details (Exploded views and 

sections at posts) 


Fence erection details (Plan views) 

18/08/09 1.8-3.0 Ibex security fence (buried plated 

posts) - Panel detail 

Rev A 1.8-3.0 Ibex security fence (buried posts) - 

02/09/09 Post and stretcher bar detail 

 

 

 

 

 

 

 

1. The fencing system should only be constructed using components supplied by NK Fencing Limited. 

2. The fencing system is available in configurations to suit either surface mounting onto hard surfaces or embedding within concrete 

foundations placed in the ground. 


installed in accordance with the documents listed in the table above entitled ‘Approved Assembly and Installation Drawings’. 




TangoRail Limited 

Units 1-3,, Prothero Industrial Estate, Bilport Lane, Wednesbury, West Midlands WS10 0NT, United Kingdom 

Tel: +44 (0)844 8360008 • Fax: +44 (0)844 8360009 

E-mail: info@tangorail.com • Website: www.tangorail.com 



Product Name Type Height (m) Post Centres 

(m) 

TangoRail 

TR100 

TangoRail 

TR200 

TangoRail 

TR150 

TangoRail 

TR250 

TangoRail 

TR300F 

TangoRail 

TR300P 

TangoRail 

TR400 

Railings 

Railings 

Railings 

Railings 

Railings 

Railings 

Railings 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

1.8, 2.0, 2.1 and 

2.4 

Gradients 1 Angles In Fence 

Line 2 

2.84 16.5° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.84 16.5° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.755 17° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.755 17° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.84 16.5° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.84 16.5° 3 75° to 105°, 

165° to 195° and 

255° to 265° 

2.84 16.5° 3 75° to 105°, 

165° to 195° and 

255° to 265° 


Rating No. 

1 942a/01 

1 942a/02 

1 942a/03 

1 942a/04 

1 942a/05 

1 942a/06 

1 942a/07 

484 20 Nov 2011



3 

Component Type Description TangoRail Fencing System 

Principle Components 

TR100 TR200 TR150 TR250 TR300F TR300P TR400 

Finials 

Fishplates 

Fullered Fullered finial 

Point Point top finial 

Intermediate 

fishplate 

Corner 

fishplate 

Fishplate 

used to attach 

rails to 

intermediate 

posts. These 


the fence 

between 165° 

and 195° 1 

Fishplate 

and 265° 1 

used to attach 

rails to 

intermediate 

posts. These 


the fence 

between 75° 

and 105° and 

between 255° 

20 Nov 2011 485



Pales 

Posts 

Rails 

Standard 

capped 

pales 

Standard 

mitred pales 

25.5 mm 

(outer 

diameter) 

steel tubes at 

0.125 mm 

centres 

25.5 mm 

(outer 

diameter) 


0.125 mm 

centres 

TR300 pales 25.5 mm 

(outer 

diameter) 


0.125 mm 

centres 

Security 

capped 

pales 

Security 

mitred pales 

Square bar 

capped 

pales 

HD rolled 

formed posts 

HD1 rails 

HD2 rails 

HD3 rails 

25.5 mm 

(outer 

diameter) 


0.103 mm 

centres 

25.5 mm 

(outer 

diameter) 


0.103 mm 

centres 

25 mm by 

25 mm steel 

tubes at 

0.125 mm 

centres 

HD rolled 

formed post of 

nominal cross 

section 

117 mm by 

43.5 mm 

55 mm by 

52 mm by 

1.5 mm rail 

55 mm by 

52 mm by 

1.5 mm rail 

55 mm by 

52 mm by 

1.5 mm rail 

 

 

 

 

 

 

 

 

 

 

Approved Assembly and Installation Drawings 4 

486 20 Nov 2011

Document 

Ref. 

Form 42 

(TangoRail 

TR100, 

TR200 and 

TR400) 

Form 42 

(TangoRail 

TR150 and 

TR250) 

Form 42 

(TangoRail 

TR300F and 

TR300P) 

Notes 

Revision / 

Issue Date 


11/11/10 Customer 

information 

(Contour 

Capped / Mitred / 

Square Bar) 


information 

(Contour 

Capped / Mitred / 

Square Bar) 


information 

(Contour 

Fullered Top / 

Point Top) 

TangoRail Fencing System 



TR100 TR200 TR150 TR250 TR300F TR300P TR400 

 

 

 

 

 

1. The gradient is based on a maximum rake of 800 mm along the length of the rail. It relates to the 2.0 m and 2.4 m high fences. The 

scope of approval for the 1.8 m high fences only covers fences installed on flat level ground. 



3. The fencing system should only be constructed using components supplied by TangoRail Limited. 

4. The fencing system is approved for installation into foundations buried in the ground, as detailed on the documents listed in the 

table above entitled ‘Approved Assembly and Installation Drawings’. The approval does not cover the use of base plated posts 

surface mounted on top of the ground. 

5. It is important to ensure the local ground onto/into which the fence is installed offers compatible strength. 



Tel: +44 (0)1429 867 388 • Fax: +44 (0)1429 867 355 




Product 

Type 

Name 

1576 Expanded metal mesh security fencing 

system 

Height Maximum Post Centres Security Cert. 

(m) 

(m) 

Rating No. 

2.4 3 2 731c/01 

Principal Components 1 

20 Nov 2011 487




Panels Expamet 1576 Expanded metal mesh panels 

Posts 

2.4 1576 Inter Post 3.215 m long intermediate post to suit 2.4 m 

high fence 

2.4 1576 Corner Post 3.215 m long corner post to suit 2.4 m high 

fence 

Stringers Diamond stringer Five stringers are located between each pair of 

adjacent posts on the non-attack side of the 

fence panel. 

Clamping Strips FCS 2440 

2.44 m long clamping strips secured to the 

attack face of each intermediate post. 

Corner clamp plate 2.44 m long ‘L’ section clamping plates secured 

to the attack face of each corner post. 

Notes 

1. The fencing system should be constructed using components supplied by The Expanded Metal Company Limited. 

2. The fencing system is approved for installation onto flat level ground of compatible strength in accordance with the instructions 

contained in document ‘1576/INST’ (Rev. D, 2/4/09). 


Security Fencing System 

Product 

Type 

Name 

1576 Class Twin-skinned expanded metal 

3 

mesh fencing system 

Height 

(m) 

Post 

Centres (m) 

Gradients 1 Angles in 

Fence Line 2 

2.465 0.5 to 3.0 0° 90°, 180° and 

270° 


Rating No. 

3 731e/01 



Posts 

Intermediate posts (180°) 

Corner posts (90° and 270°) 

End posts 

80 mm by 40 mm by 3 mm galvanised steel posts. 

100 mm by 100 mm by 4 mm galvanised steel posts w ith 80 mm by 40 mm by 

3 mm RHS boxes running up adjacent sides. 

80 mm by 40 mm by 3 mm galvanised steel posts. 

Mid lugs 

35 mm high by 150 mm long by 5 mm thick galvanised steel flats for use on 

intermediate posts (six per post). 

End lugs 

35 mm high by 90 mm long by 5 mm thick galvanised steel flats for use on end 

posts and corner posts (six per post). 

Panels Galvanised mesh panels 1576 expanded metal mesh panels 3 . 

Horizontal rails Diamond stringer Six stringers are located betw een each pair of adjacent posts. These are 

sandw iched betw een the tw o mesh layers forming each fence panel. 

Clamping strips Flat clamp strip 

40 mm w ide by 5 mm thick by 2465 mm long galvanised steel bar. 

Corner clamp plate 

149 mm w ide by 2 mm thick by 2465 mm long ‘L’ shaped galvanised steel bar. 


Document Reference Revision Title / Contents 

1576/C3/ILLUST 

1576/C3/INST 

D 

20/04/2011 

E 

20/04/2011 

1576 Fencing - Class 3 

1576 Class 3 Fencing Installation 

Notes: 

1. The fencing system is approved for installation into flat ground of gradients 0°. 

488 20 Nov 2011





3. Mesh panels must be attached to the front and rear of the posts and stringers and overlap adjacent panels by at least 150 mm at 

intermediate posts. 

4. The fencing system should only be constructed using components supplied by The Expanded Metal Company Limited. 

5. The fencing system is only available for embedding into concrete foundations placed within the ground. 


installed in accordance with the documents listed in the table entitled ‘Approved Assembly and Installation Drawings’. 

20 Nov 2011 489


SECURITY GATES 



Tel: +44 (0)1270 764751 • Fax: +44 (0)1270 757503 


Certificate No: 999b to LPS1175: Issue 7 

Security Gates 

Product 

Name 

Lockmaster 

Type 

Height 

(m) 

Minimum Width 

(m) 

Maximum Width 

(m) 

Security 

Rating 

Single leaf inward opening 2.44 0.6 3 2 999b/01 

security gate 1 

Double leaf inward opening 

security gate 1 2.44 1.2 6 2 

Cert. 

No. 


Reference Manufacturer Model Type Compatible operating devices Com patible 

External face Internal face 

cylinders 

1 Chubb B-3C16-PL-80 2 Mortice hook Key Key A and B 

lock 

2 Ingersoll London Line B- Mortice hook Key Key A and B 

SC110-CH 2 lock 

3 3 CLD Fencing 

Systems 

Drop bolt Drop bolt - Handle - 


Reference Manufacturer Model Type 

A Eurospec CYA 74260PC Euro-profile double cylinder (key:key) 

B Mul-T-Lock Interactive Euro-profile double cylinder (key:key) 

Notes: 

1. The gate is available in configurations to suit either surface mounting onto hard surfaces 4 or embedding within concrete foundations 

placed in the ground 4 . 

2. Fitted with an LS2 cylinder guard supplied by Tindall Engineering Limited. 

3. This option is only available on double leaf gates. The security rating noted above will only be achieved if the primary locking device 

(i.e. those referenced as ‘1’ and ‘2’ in the compatible locking devices table) is engaged. 

4. It is important to ensure that the local ground onto/into which the gate is installed offers compatible strength. 

5. The gap between the gate posts and adjacent structures must not exceed 220 mm. 

6. The gap between the bottom of the gate leaf and the ground must not exceed 50 mm. 



Tel: +44 (0)1429 867 388 • Fax: +44 (0)1429 867 355 



Vehicle and Pedestrian Gates 

Product 

Name 

Type Width (mm) Height 

(mm) 

Security 

Rating 

Cert. 

No. 

Alleygator Pedestrian alley gate 810, 1000, 1100 and 2350 1 731a/01 

1600 

Vehicle alley gate 2150, 2300, 2450, 3010 

and 3300 

2350 1 731a/02 

490 20 Nov 2011


SECURITY GATES 

Product 

Name 

Type Width (mm) Height 

(mm) 

Security 

Rating 

Cert. 

No. 

Vehicle alley gate incorporating inner 2150, 2300, 2450, 3010 2350 1 731a/03 

pedestrian alley gate 

and 3300 

Pedestrian alley gate 

810, 1000, 1100 and 2350 2 1 731a/04 

1600 

Vehicle alley gate 2150, 2300, 2450, 3010 2350 2 1 731a/05 

and 3300 

Vehicle alley gate incorporating inner 

pedestrian alley gate 

2150, 2300, 2450, 3010 

and 3300 

2350 2 1 731a/06 

Compatible locking systems 

Model Type Compatible 

Cylinders 

Wilka 5495 

Compatible accessories 

Self locking 


mortice lock 

Approved Product (LPCB Ref. No. 731a/...) 

01 02 03 04 05 06 

Dom 333i5HT 

Model Type Approved Product (LPCB Ref. No. 731a/...) 

01 02 03 04 05 06 

Roller top 2 Anti-scaling 

attachment for top 

of gate 

 

Notes 

1. The deadlock must be fully thrown by turning the key twice in order for the gate to meet Security Rating 2. 

If the key is only thrown once the gate achieves Security Rating 1. 

2. The roller top option can be fitted without undermining the attack resistance provided by the gates. 

However, the roller top’s resistance to removal is not covered by this approval nor is its resistance to scaling. 

3. The gap between the gate and the adjacent walls must not exceed 45 mm. 

4. The gap between the bottom of the gate leaf and the ground must be within the following range: 

(i) 10 mm to 110 mm - Alleygator TM pedestrian alley gates. 

(ii) 50 mm to 150 mm - Alleygator TM vehicle alley gates and vehicle alley gates incorporating pedestrian gates. 

20 Nov 2011 491


TURNSTILES 

Frontier-Pitts Limited 

Crompton House, Crompton Way, Manor Royal Industrial Estate, Crawley, West Sussex RH10 9QZ, United 

Kingdom 

Tel: +44 (0)1293 548301 • Fax: +44 (0)1293 560650 

E-mail: sales@frontierpitts.com • Website: www.frontierpitts.com 


Full Height Turnstile 

Product Type 

Name 

Terra 

Diamond 

Grade 3 

Terra 

Diamond 

Grade 4 

Single full 

height 

turnstile 

Single full 

height 

turnstile 

Number of 

Rota Arms 

Walkway 

Width (m) 1 

Nominal 

Overall Unit 

Height (m) 2 

Nominal 

Overall Unit 

Width 2 

Nominal 

Overall Unit 

Depth 2 

Security 

3, 4, 5 

Rating 

Cert. No. 

Four 0.5 2.387 1.380 1.390 3 1059a/01 

Four 0.5 2.387 1.380 1.390 4 1059a/02 

Notes: 

1. This is measured at the outside entrance to the turnstile. 

2. These dimensions are of the entire unit. They include the enclosure above the rotor that contains the drive and control mechanism, 

but exclude those of the foundations. 

3. The turnstiles achieve these security ratings when installed and maintained in accordance with the instructions contained in the Terra 

Diamond Turnstile Operating and Maintenance Manual (document reference 6614-O&M Issue 4 dated 7 April 2011) and ‘Diamond 

Turnstile Installation Procedure (document reference 6614-IP Issue 2 dated 9 March 2011), placed in the ‘power to release’ (normal 

automatic) mode and operated from the ‘attack’ side using an access control system 6 having at least 30,000 effective differs that 

offers compatible resistance to manual attack. 

4. The turnstiles offer resistance to attack commensurate with at least Security Rating 1 when placed in the ‘manual release’ mode. 

5. The security ratings noted indicate the turnstile’s resistance to forced entry from the outside when mounted within barriers that offer 

compatible resistance to forced entry in accordance with LPS 1175: Issue 6. 

6. The resistance of the access control system, used to operate the turnstiles, to ‘non-mechanical’ attack is not covered as it is outside 

the scope of LPS 1175: Issue 6. Likewise, the approval does not cover possible effects of any susceptibilities relating to the 

functionality and performance of any access control equipment that may be used to operate the turnstiles. This is because the scope 

of access control devices and system configurations that may be used with these locking systems is “infinite”. It is therefore 

recommended that specifiers satisfy themselves that the components used are either resistant to mechanical and other forms of 



492 20 Nov 2011


VEHICLE SECURITY BARRIER 

This section will include vehicle security barriers such as: 

Fixed bollards 

Rising bollards 

Road blockers 

Drop arm barriers 

Vehicle security barriers and their associated foundations will be evaluated against the requirements of PAS 

68: 2010 Impact test specifications for vehicle security barriers, a standard drawing on the draft LPS 1246 

Requirements and test methods for classifying security bollards originally developed by LPCB. 

Barriers are classified according to the following measurements after a single impact by a vehicle of a defined 

mass, velocity and angle of impact: 

The distance the vehicle passed beyond the plane of the barrier. 

The distance the major debris dispersed beyond the plane of the barrier. 

It is also intended that, where requested by the manufacturer, the barriers’ resistance to manual attacks aimed 

at compromising their resistance to vehicle attack will be rated in accordance with LPS 1175 Requirements 

and testing procedures for the LPCB approval and listing of intruder resistant building components, 

strongpoints, security enclosures and free-standing barriers. 

LPCB is also working closely with the Perimeter Security Suppliers Association (PSSA) and leading 

independent laboratories, such as TRL, to develop criteria evaluating and approving other aspects of the 

barriers performance and durability. 

This will enable specifiers to select vehicle barriers suitable to the risks identified during a risk assessment of 

the facilities to be protected. 

20 Nov 2011 493


GAS CYLINDER SECURITY DEVICES 

This section lists gas cylinder security devices that have been approved to LPS 1175 Requirements and 

testing procedures for the LPCB approval and listing of intruder resistant building components, 

strongpoints, security enclosures and free-standing barriers. 

The approval covers the resistance to unauthorised removal of gas cylinders provided by the security devices 

when installed and maintained in accordance with the approved instructions. 

While previous versions of the standard specified six levels of resistance (security ratings), the latest version 

(Issue 6) specifies eight security ratings. These range from opportunist (1 minute attacks using easily 

concealable hand tools) up to extreme methods of attacks (20 minute attacks using a wide range of hand 

tools, power tools and thermal cutting equipment). 

Further details of the grading system can be found in the standard itself, copies of which are available free of 

charge and can be downloaded from www.RedBookLive.com. 

The approval does not cover the resistance to unauthorised operation of the gas cylinders when secured by 

the devices listed. 


When selecting a gas cylinder security device, check that the product’s approval covers the types and sizes of 

cylinders to be secured, the compatible locking systems listed and the substrates to which the devices may be 

fixed in order to provide secure anchorage - all can affect the level of security provided by the product. 

To enable selection of the most appropriate product for the desired application, the listing defines the gas 

cylinders that are covered by the scope of approval in terms of the supplier, supplier reference and following 

dimensions: 

Key: 

h a = Height of cylinder, including foot ring and neck ring and/or valve cap 

h b = Height of cylinder to base of neck ring 

h c = Height of cylinder to edge of shoulder 

h d = Height of foot ring 

d a = Diameter at base of neck ring/valve cap 

d b = Diameter of cylinder 

To achieve the security ratings: 

(a) the gas cylinder security devices must be installed in accordance with the manufacturer’s instructions; 

494 20 Nov 2011



(b) all locks must be fully engaged and deadlocked; and 

(c) all exposed fixings, the substrate onto which each device is fitted and the locking mechanism(s) must be 

regularly checked to ensure they are in good condition and that they have not been tampered with. 



Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 



Gas Cylinder Security Devices 

Product Name Model Type Compatible Gas 

Cylinders 

Security 

Rating 

Cert. 

No. 

Liddle Series 2 Bottle Storage LD Type A Three bottle storage 1, 4, 5 and 6 2 442c/01 

Frame 

(CL2) 

frame 

LD Type A Three bottle storage 

2 2 

(SO2) 

frame 

LD Type A Three bottle storage 

3 2 

(NH3) 

frame 

LD Type B Two bottle storage 

1, 4, 5 and 6 2 

(CL2) 

frame 


2 2 

(SO2) 

frame 


3 2 

(NH3) 

frame 

LD Type C Four bottle storage 1, 4, 5 and 6 2 

(CL2) 

frame 

LD Type C Four bottle storage 

2 2 

(SO2) 

frame 

LD Type C Four bottle storage 

3 2 

(NH3) 

frame 

LD Type D Six bottle storage 

1 2 

(CL2) 

frame 

LD Type D Six bottle storage 

2 2 

(SO2) 

frame 

LD Type F Single bottle storage 1, 4, 5 and 6 2 

(CL2) 

frame 

LD Type F Single bottle storage 

2 2 

(SO2) 

LD Type F 

(NH3) 

frame 

Single bottle storage 

frame 

3 2 


Model Type Cylinder 

Abloy PL340 Padlock Abloy High Profile 

Abloy PL340 Padlock Abloy Disklock Pro 

Abloy PL340 Padlock Abloy Exec 

Abloy PL340 Padlock Abloy Protec 

Abloy PL342 Padlock Abloy High Profile 


Abloy PL342 Padlock Abloy Exec 


Compatible Gas Cylinders 

20 Nov 2011 495



Cylinder 

Reference 

Supplier 

Model 

Reference 

Height 3 (mm) 

Diameter 3 (mm) 

Notes 

h a h b h c h d d a d b 

1 BOC BKA 1120 1000 930 65 75 300 

2 BOC BD 910 780 700 60 140 320 

3 BOC BE 1265 1120 1035 85 90 380 

4 BOC E3 1060 940 890 45 75 220 

5 Ineos 71kg 1130 1020 950 65 85 290 

6 Ineos 33kg 1050 940 840 n/a 85 220 

1. The 'Liddle Series 2 Bottle Storage Frames' are approved when installed directly onto a flat solid concrete floor. 

2. The security rating afforded to the 'Liddle Series 2 Bottle Storage Frames' is based upon every bay within the frame containing a 

cylinder of the relevant type and dimensions specified. 

3. For a key to the cylinder dimensions refer to the introduction of the gas cylinder security device section of the Red Book 

(RedBookLive.com). 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 



Gas Cylinder Security Devices 

Product Name Type Gas Cylinders Security Rating Cert. No. 

Ultrasecure Cylinder Clamp Single cylinder clamp 1, 2, 3, 4 and 5 2 450e/01 


Model Type Cylinder 



Kaba K20SS65L Padlock Kaba 20 (Armoured) 

Kaba Thorlock Integral lock Kaba 20 (Armoured) 

Compatible Gas Cylinders 

Cylinder 

Reference 

Note 

Supplier 

Model 

Reference 

Height (mm) 

Diameter 

(mm) 

h a h b h c h d d a d b 

1 IneosChlor 71 kg 1130 1020 950 65 85 290 

2 IneosChlor 33 kg 1050 940 840 n/a 85 220 

3 BOC BKA 1120 1000 930 65 75 300 

4 BOC E3 1060 940 890 45 75 220 

5 BOC BD 910 780 700 60 140 320 

1. The device is approved when installed in accordance with document CCU-DV-FIT-01 (Issue 2). 

496 20 Nov 2011


PHYSICAL SECURITY DEVICES FOR COMPUTERS AND OTHER ICT EQUIPMENT 

At the request of the Association of British Insurers, the LPCB developed LPS 1214 Specification for testing 

and classifying physical protection devices for personal computers and similar equipment for the performance 

of security equipment designed to prevent removal of computer and other office equipment: 

The standard currently defines two categories of protection. Both categories of device prevent theft of the 

complete computer for three minutes allowing a response by Police or security guards, while Category II 

products also prevent removal of the computer chips for the same period. 

Suitable applications for products certified to LPS 1214 are described below: 

Category I: 

Category II: 

Prevent unauthorised removal of personal computers (PCs), file 

servers, printers, facsimile machines and other high value equipment 

for example where access is important for use and the component 

value is low. 

Prevent unauthorised removal of or access to personal computers 

(PCs), file servers, printers, facsimile machines and other high value 

equipment for example where the PC is both important and highly 

valued and/or the component value is high. 

Specifiers requiring category II devices should ensure that they select a device suitable for their particular 

equipment and that there is suitable ventilation of the computer in accordance with any instructions and 

warranty conditions supplied with the computer. 

In order that they will provide the required protection, the approved equipment must be installed in accordance 

with the manufacturer’s instructions and be in the locked condition with keys removed and held in a secure 

location. 

It is recommended that users regularly check that all exposed fixings and locking mechanisms are in good 

condition and that they have not been tampered with. 

In addition to approving physical protection devices for personal computers and similar equipment to LPS 

1214, LPCB also evaluate and approve the following equipment designed to secure larger volumes of ICT 

equipment to LPS 1175 Requirements and testing procedures for the LPCB approval and listing of intruder 

resistant building components, strongpoints, security enclosures and free-standing barriers: 

- Racking systems 

- Modular enclosures 

- Composite panelling systems designed for constructing data halls. 

Security products approved to LPS 1175 Security Rating 2 provide an equivalent resistance to forced entry as 

that provided by an LPS 1214 Category I device. 

It should be noted that the resistance provided by each enclosure approved to LPS 1214 category I or LPS 

1175 Security Rating 2 used to secure individual items of ICT equipment matches the resistance provided by 

products, such as doors and partitioning systems, rated to Security Rating 2 in LPS 1175 that secure larger 

quantities of ICT equipment. It is therefore recommended that specifiers individually secure items of ICT 

equipment especially when located in multi-user spaces, such as schools and offices, and open access areas 

such as libraries. 

It is also recommended that all equipment is marked with an asset management marking system approved to 

LPS 1225 and registered on a secure asset database certified to LPS 1224. Marking devices and secured 

database services are listed in Sections 13 and 14 of Part 4. 

Products that have been certified by LPCB should be marked with a label indicating the level of security 

offered, LPCB certification mark and certificate number. 

20 Nov 2011 497





Tel: +44 (0)1724 271999 • Fax: +44 (0)1724 271888 



Server Security Cabinets 

Product 

Name 

Type Model Height 

(mm) 

Width 

(mm) 

Depth 

(mm) 

Security 

Category 

Cert. 

No. 

Ventis Server Server enclosure with 

- 2127 725 1100 II 312b/03 

Safe single door in front and rear 

Sun Safe Server enclosure with UKT-SUNSAFE-1 2160 725 1500 II 

System Vault single door in front and rear 

Server enclosure with UKT-SUNSAFE-2 2160 725 1265 II 

single door in front and rear 







Server enclosure with Made to measure: 1000 600 600 II 

single door in front and rear min. size 

Server enclosure with Made to measure: 2500 1000 2000 II 

single door in front and rear max. size 


double door in front and 

rear 



rear 



rear 

Server enclosure with 


rear 

Made to measure: 

min. size 

1000 700 600 II 

Server enclosure with 


rear 

Made to measure: 

max. size 

2500 2000 2000 II 


Lock Type Cylinder 

Dom Nemef DDLK Mortice Lock Mul-T-Lock Interactive single Euro-profile cylinder 

or 

Santos 725 single Euro-profile cylinder 

Notes 

1. The above approval applies to these products when assembled and installed strictly in accordance with the instructions provided 

with the product. 

2. In order to offer the required level of security, all locks must be engaged and the keys removed. 

Dalen Limited 

Valepits Road, Garretts Green Industrial Estate, Birmingham B33 0TD, United Kingdom 

Tel: +44 (0)121 783 3838 • Fax: +44 (0)121 784 6348 

E-mail: sales@top-tec.co.uk • Website: www.top-tec.co.uk 


498 20 Nov 2011

Computer Security Devices 

Product 

Name 

Type Maximum 

Computer 

Height 

(mm) 

T-T450/1 Adjustable 

tower 

computer 

security cage 


tower 

computer 

security cage 


tower 

computer 

T-T418 

(4) 

T-T419 

T-T540 

Nightsafe 

security cage 

Front 

opening 

bespoke 

range of 

security 

entrapments 

for tower 

computers 

Front 

opening 

bespoke 

range of 

security 

entrapments 

for tower 

computers 



Maximum 

Computer 

Width 

(mm) 

Maximum 

Computer 

Depth 

(mm) 

Minimum 

Computer 

Height 

(mm) 

Minimum 

Computer 

Width 

(mm) 

Minimum 

Computer 

Depth 

(mm) 

Security 

Category 

Cert. 

No. 

380 190 - 330 165 440 I 276a/01 

430 190 - 380 165 440 I 276a/02 

180 515 700 100 300 355 I 276a/03 

700 400 700 250 180 300 I 276a/04 

300 800 700 110 200 350 I 276a/05 

Modular 

laptop 

security 

enclosures 3 500 250 500 330 95 330 II 276a/06 

Notes 

1. The approval applies to these products when installed strictly in accordance with the instructions provided with the product. 

2. The substrate and fixings for wall and floor mounting may affect the performance of the product and are therefore outside the scope 

of the approval. 

3. The Nightsafe units are modular units available with between three and nine compartments each designed to take computers within 

the size range specified above. 

4. The T-T418 may also be sold under the alternative model reference T-T SE 0250. 


Projector Security Devices 

Product Name Cage 

Dimensions 

Cage 

Dimensions 

Cage 

Dimensions 

Pole 

Length 

Pole 

Length 

Security 

Category 

Cert. 

No. 

Depth 

(mm) 

Width 

(mm) 

Height 

(mm) 

Minimum 

(mm) 

Maximum 

(mm) 

T-T140/3 Projector 386 319 115 500 1500 I 276b/01 

cage 

T-T140/4 Projector 

cage 

386 319 140 500 1500 I 276b/02 

Suitable for use with the projectors within the following size range: 

Product Name 

Minimum 

Maximum 

Depth 

(mm) 

Width 

(mm) 

Height 

(mm) 

Depth 

(mm) 

Width 

(mm) 

Height 

(mm) 

T-T140/3 Projector cage 150 150 50 225 340 95 

T-T140/4 Projector cage 150 150 50 225 340 115 

Compatible locks 

20 Nov 2011 499



Lock Designation 

T-T140 (LPCB Ref. No. 276b/...) 

01 02 

Lowe and Fletcher 10 pin radial tumbler lock 

Manseng Enterprise Co. Ltd, 7 pin radial push button lock 

Note 

1. The approval only applies to the projector cages when used in conjunction with the T-T105 pole and T-T105-CU ceiling unit, and 

installed strictly in accordance with the following instructions: 

T-T140 iss5.pub 

CC_INST T-T 105-CU iss3.pub 

CC_INST T-T 105-Pole iss1.pub 

500 20 Nov 2011


DATABASE MANAGEMENT FOR ASSET MARKING 

The essential requirements of LPS 1224:Issue 2 Requirements for Secure Database Registers were 

developed as a result of needs identified by the Police, Insurers and Home Office. LPS 1224 ensured that 

Police and other legitimate enquirers can confirm ownership of property 24 hours a day while ensuring full 

details of property ownership are held securely and in accordance with the Data Protection Act. 

Therefore, under the requirements of LPS 1224, the database operator must: 

(i) Have an established track record in the field of asset registration of at least one year. 

(ii) Operate the database in accordance with a documented set of procedures in accordance with the 

requirements defined in LPS 1224. 

(iii) Offer a telephone check line service manned by trained operatives. In accordance with Government 

policy, the service shall be available 24 hour a day access and shall be free of direct charge to the enquirer, 

e.g. it shall not chargeable to the enquirer as a premium rate telephone service. 

This section lists companies that run databases that have been assessed and approved to LPS 1224. More 

recently LPS 1224:Issue 3 Requirements for companies providing security asset registration services was 

developed. This covers database services provided over the internet as well as those which may be accessed 

using other media. 

Datatag ID Limited 

3000 Hillswood Drive, Hillswood Business Park, Chertsey, Surrey KT16 0RS, United Kingdom 

Tel: +44 (0)1932 895304 • Fax: +44 (0)1932 796797 

E-mail: info@datatag.co.uk • Website: www.datatag.co.uk 

24/7 Telephone Number: 0845 0700 440 


Secure Database Register 

Product Name Telephone Number Web Address Cert. No. 

Datatag ID Secure Database 08450 700440 as above 665a/01 

Retainagroup Limited 

Unit 5, St John's Court, Foster Road, Ashford Business Park, Ashford, Kent TN24 0SJ, United Kingdom 

Tel: +44 (0)1233 506400 • Fax: +44 (0)1233 506401 

E-mail: cust.service@retainagroup.co.uk • Website: www.retainagroup.com 

Certificate 493a 

5 Windward House, Plantation Wharf, London SW11 3TU, United Kingdom 

Tel: 24 hour 07000 111333 



Product Name Telephone Number Web Address Cert. No. 

International Security Register 07000 111333 As above 493a/01 

20 Nov 2011 501


DATABASE MANAGEMENT FOR ASSET MARKING 

Selectamark Security Systems plc 

1 Locks Court, 429 Crofton Road, Locksbottom, Kent BR6 8NL, United Kingdom 

Tel: +44 (0)1689 860757 • Fax: +44 (0)1689 860693 

E-mail: sales@selectamark.co.uk • Website: www.selectadna.co.uk 



Product Name Telephone 

Number 

Selectamark +44 (0)1689 

Secure Asset 860757 

Register 

Hours of Operation 1 Web Address Postal 

Address 

9 am to 5 pm on 

www. 

1 Locks 

weekdays, excluding secureassetregister.com Court, 

bank holidays 

429 Crofton 

Road, 

Locksbottom 

Kent BR6 

8NL 


Level No. 

2 497b/01 

Note: 

1. These are the hours during which the telephone helpline is available. These are based on UK time. 

502 20 Nov 2011


ASSET MARKING SYSTEMS 

The following marking devices listed have been tested to LPS 1225 Specification for testing and classifying 

asset marking systems. 

LPS 1225 specifies requirements for the composition and performance of an asset marking system such that, 

when used according to the manufacturer’s instructions, the asset marking device may: 

i) Enable the marked asset to be traced to the legal owner via a secure database register linked to the 

marking system employed. 

ii) 

Act as a theft deterrent in the first instance by virtue of known existence. 

It is assumed that the part of the asset to which the asset marking device is applied is at least equal in 

resistance to removal from the asset as the asset marking device employed. 

The two-part classification indicates the resistance of the product to eradication of ownership traceability and 

resistance to complete removal of marking without leaving evidence of previous existence. This gives the enduser 

the option of selecting a product to suit the required application. Complete removal of the marking and 

restoration of the asset gives maximum resale value to the stolen asset; however the standard does not take 

into account replication or replacement of components as part of asset restoration. 

The overall classification designation achieved is given by two numerals separated by a plus sign. The first 

numeral represents the resistance rating to erasure of traceability and the second numeral to complete 

removal/asset restoration. 

The two classifications are both on a scale of one to eight. Classification ‘1’ performance relates to that which 

should be expected as a minimum for marking devices used in the retail trade and other public areas 

equipped with CCTV and security staff. Classification ‘8’, on the other hand, is aimed at marking devices 

applied to assets that have a high value and this will be the subject of a more determined level of effort by the 

criminal in order to prevent traceability or completely remove the mark. 

Long term durability of the system and associated components are beyond the scope of this standard, as are 

the performance requirements of any covert marking technology incorporated in the system. 

Although this standard specifies that the product instructions shall include hazard data, confirmation of the 

authenticity of such data is not addressed. 

All approved marking devices are marked with a unique asset identification code. The LPCB certification mark 

and reference numbers relating to the marking device and database, and the telephone number of the 

database will also be marked on the marking device, or where this is not viable, on separate warning labels 

which are supplied with the marking device. 

In addition to LPS 1225, LPCB is currently working with manufacturers and specifiers to finalise standards 

classifying the performance of “microdot”, “trace chemical” and RFID marking systems. Please contact LPCB 

for further details. 

20 Nov 2011 503





Tel: +44 (0)1233 506400 • Fax: +44 (0)1233 506401 


Certificate 493b 


Tel: 24 hour 07000 111333 


Overt Asset Marking Systems 

Product Name Substrate Resistance 

Rating 


Database 

Ref. No. 

The Retainagroup Marking and Registration System for Vehicles Float glass 2 + 8 493a/01 493b/01 

Marking and Registration System for Vehicles 

Laminated 2 + 8 493a/01 

glass 

Toughened 2 + 8 493a/01 

glass 

The Retainagroup Marking and Registration System for Office and 

Household Equipment 

ABS Plastic 1 + 2 493a/01 493b/02 

Cert. 

No. 

Note 

1. Effective marking of materials, in particular plastics, is dependent upon the specific material type, material constituents and surface 

finish. If you are in any doubt over the likely performance of these marking devices in your situation please contact the 

manufacturer. 



Tel: +44 (0)1689 860757 • Fax: +44 (0)1689 860693 



Overt Asset Marking Systems 

Product Name 

Type of 

Marking 

Substrate 

Resistance 

Rating 

Database 

Ref. No. 

Cert. 

No. 

Device 


Selectamark Glass etching compound Float glass 1 + 8 379a 497a/01 

(7mm) 

'Blue' etching compound ABS plastic 1 + 2 379a 497a/02 

'Blue' etching compound Enamel finished steel 1 + 1 379a 

'Blue' etching compound Leather 1 + 2 379a 

'Blue' etching compound Polycarbonate 2 + 5 379a 

'Blue' etching compound 

Polymethyl Methacrylate 

1 + 3 379a 

("Perspex") 

'Blue' etching compound Planed softwood timber 1 + 1 379a 

'Blue' etching compound Planed hardwood timber 1 + 1 379a 

'Blue' etching compound Plywood 1 + 1 379a 

'Blue' etching compound PVC 1 + 2 379a 

'UV-Orange' etching compound ABS plastic 1 + 2 379a 497a/03 

'UV-Orange' etching compound Enamel finished steel 1 + 1 379a 

'UV-Orange' etching compound Leather 1 + 2 379a 

'UV-Orange' etching compound Polycarbonate 2 + 5 379a 

'UV-Orange' etching compound Polymethyl Methacrylate 

1 + 3 379a 

("Perspex") 

'UV-Orange' etching compound Planed softwood timber 1 + 1 379a 

'UV-Orange' etching compound Planed hardwood timber 1 + 1 379a 

504 20 Nov 2011



Product Name 

Supermark 

(5mm) 

Selectamark 

(5mm) 

Selectamark 

(7mm) 

Supermark 

(5mm) 

Type of 

Marking 

Device 

Substrate 

Resistance 

Rating 


Database 

Ref. No. 

'UV-Orange' etching compound Plywood 1 + 1 379a 

'UV-Orange' etching compound PVC 1 + 2 379a 

Label and 'Blue' etching compound ABS plastic 1 + 3 379a 497a/04 

Label and 'Blue' etching compound Enamel finish steel 1 + 2 379a 

Label and 'Blue' etching compound Polycarbonate 1 + 4 379a 

Label and 'Blue' etching compound Polypropylene 1 + 2 379a 

Label and 'Blue' etching compound Polymethyl Methacrylate 

1 + 4 379a 

("Perspex") 

Label and 'Blue' etching compound Planed softwood timber 1 + 2 379a 

Label and 'Blue' etching compound Planed hardwood timber 1 + 2 379a 

Label and 'Blue' etching compound Plywood 1 + 2 379a 

Label and 'Blue' etching compound PVC 1 + 3 379a 

Label and 'UV-Orange' etching 

ABS plastic 1 + 3 379a 497a/05 

compound 

Label and 'UV-Orange' etching Enamel finished steel 1 + 2 379a 

compound 


Polycarbonate 1 + 4 379a 

compound 


Polypropylene 1 + 2 379a 

compound 

Label and 'UV-Orange' etching Polymethyl Methacrylate 

1 + 4 379a 

compound 

("Perspex") 

Label and 'UV-Orange' etching Planned softwood timber 1 + 2 379a 

compound 

Label and 'UV-Orange' etching Planed hardwood timber 1 + 2 379a 

compound 


Plywood 1 + 2 379a 

compound 


compound 

PVC 1 + 3 379a 

'Blue' etching compound ABS plastic 1 + 2 379a 497a/02 

'Blue' etching compound Enamel finished steel 1 + 1 379a 

'Blue' etching compound Polycarbonate 2 + 5 379a 

'Blue' etching compound 

Polymethyl Methacrylate 

1 + 3 379a 

("Perspex") 

'Blue' etching compound PVC 1 + 2 379a 

'Ice Blue' etching compound ABS plastic 1 + 2 379a 497a/07 

'Ice Blue' etching compound Enamel finished steel 1 + 1 379a 

'Ice Blue' etching compound Polycarbonate 2 + 5 379a 

'Ice Blue' etching compound Polymethyl Methacrylate 

1 + 3 379a 

("Perspex") 

'Ice Blue' etching compound PVC 1 + 2 379a 

'Ice Blue' etching compound ABS plastic 1 + 2 379a 

'Ice Blue' etching compound Enamel finished steel 1 + 2 379a 

'Ice Blue' etching compound Polycarbonate 2 + 5 379a 

'Ice Blue' etching compound Polymethyl Methacrylate 

1 + 3 379a 

("Perspex") 

'Ice Blue' etching compound PVC 1 + 2 379a 

Label and 'Ice Blue' etching 

ABS plastic 1 + 3 379a 497a/06 

compound 


Enamel finished steel 1 + 2 379a 

compound 


Polycarbonate 1 + 4 379a 

compound 

Label and 'Ice Blue' etching Polymethyl Methacrylate 

1 + 4 379a 

compound 

("Perspex") 


Polypropylene 1 + 2 379a 

compound 


PVC 1 + 3 379a 

compound 

Cert. 

No. 

Note 

1. Effective marking of materials, in particular plastics, is dependent upon the specific material type, material constituents surface 

colour and finish. If you are in any doubt over the likely performance of these marking devices in your situation please contact the 

manufacturer. 

20 Nov 2011 505


'THEFT RESISTANT' ELECTRONIC PRODUCTS 

This section lists ‘theft resistant’ electronic products that have been assessed to LPS 1650 Requirements and 

testing procedures for the LPCB approval and listing of ‘theft resistant’ electronic products. This includes: 

• In-car entertainment systems • PDA’s 

• DVD players and writers • Personal computers 

• Health care equipment • Projectors and wipe boards 

• Laptops • Printers 

• Mobile telephones • Satellite navigation devices 

• MP3 players • Televisions and screens 

The attributes that make these products particularly desirable to thieves can be summarised into six elements 

and these elements are often referred to by the acronym CRAVED. Concealable, Removable, Available, 

Valuable, Enjoyable and Disposable. Whilst each element can be used to determine which products are likely 

to be stolen, the frequency at which the thefts occur may ultimately depend on just one attribute, the ease at 

which the item can be disposed. 

The intention of LPS 1650 is to encourage the use of effective security features that make it difficult to return 

the product to a ‘re-saleable’ condition if stolen, thus reducing the level to which they are craved by criminals. 

Whilst the standard does not specify any one particular design of anti-theft technology it includes 

requirements for the performance of the following types: 

• Denial of service technologies, such as PIN codes, removal 

coded panels and electronic keys 

• Asset marking systems (overt and covert) linked to secure 

databases providing traceability to the legal owner of the 

product 

• Anchoring devices providing mechanical resistance against 

unauthorised removal of the product 

• Alarm /signalling technologies providing warning of attempted 

removal 

– Use of effective denial of service technology can prevent the 

product being enjoyed by persons other than the legitimate 

owner(s). 

– Asset marking that cannot be removed without damaging the 

product can make it harder for the thief to dispose of the item 

and reduce the value of the goods if removal is attempted. 

– Secure fixing to a solid mounting surface can increase the 

effort required to remove the product. 

– An audible alarm could make the product less concealable. 

The requirements and tests of LPS 1650 permit the assessment and rating of the performance of the anti-theft 

security features built into or supplied with the product. 

Where appropriate reference is made to specific requirements of standards such as LPS 1224 Requirements 

for secure database registers, LPS 1225 Requirements for the LPCB approval and listing of asset marking 

systems, LPS 1214 Specification for testing and classifying physical protection devices for personal 

computers and similar equipment and a number of other applicable European standards. 

The overall security performance rating is indicated by a series of security performance classifications. To 

meet the minimum requirement of LPS 1650 products must achieve at least one denial of service 

classification. The security performance rating is expressed in the following format: 

506 20 Nov 2011


'THEFT RESISTANT' ELECTRONIC PRODUCTS 

For details of the security performance rating parameters and their classification refer to LPS 1650. 

20 Nov 2011 507


LETTER PLATES AND LETTER BOXES (MAIL BOXES) 

Letter plates and letter boxes (otherwise known as mail boxes) listed within this section have been evaluated 

in accordance with either LPS 1175 Specification for testing and classifying the burglary resistance of building 

components, strongpoints and security enclosures or BS EN 13724: 2002 Postal services - Apertures of 

private letter boxes and letter plates - Requirements and test methods. 

LPS 1175 currently specifies eight grades of security according to the severity of the likely attack ranging from 

opportunists (security rating 1) through to professional criminals. The ratings are determined in terms of attack 

tools and time available to the attacker, and enables specifiers to select products according to the risks that 

they and their property face. The failure criteria used will suit the intended application of the products listed. 

These may include boxes designed to prevent the unauthorised removal of the contents of a letter box to 

letter plates and boxes with lockable flaps that are designed to prevent deliveries being made during periods 

when the properties to which they are fitted are left empty. 

Details regarding the classification system used when rating products to LPS 1175 can be found within the 

standard itself, copies of which are available free of charge and can be downloaded from the LPCB web site 

www.RedBookLive.com. 

BS EN 13724: 2002 classifies apertures of letter boxes and plates according to the following: 

Type of aperture 

Size of aperture 

Corrosion resistance and water penetration 

Security. 

The classification is determined by taking a series of measurements and conducting a series of mechanical 

tests including soak tests (water), salt spray tests to EN 1670 (corrosion) and load tests (security). The 

security requirements contained within BS EN 13724: 2002 are considered to be less severe than those of the 

minimum security rating defined in LPS 1175, i.e. Security Rating 1. 

It is important to ensure that the letter plates and boxes are installed in accordance with the manufacturers 

instructions and that all exposed fixings, the substrate to which the product is fitted, and any locking 

mechanisms incorporated within the product are regularly checked to ensure that they are in good condition 

and that they have not been tampered with. 

The Safety Letter Box Company Limited 

Unit 1B, Milland Industrial Estate, Milland Road, Neath, West Glamorgan SA11 1NJ, United Kingdom 

Tel: +44 (0)1639 633525 • Fax: +44 (0)1639 646359 

E-mail: info@safetyletterbox.com • Website: www.safetyletterbox.com 


Security Letter plate 

Product 

Name 

Type Scope of Installation Security 

Rating 

Cert. 

No. 

Flaplock 

FL05 

Internal letter 

plate 

Mounting on the rear of 44 mm thick solid timber door leaves over letter 

slots measuring 45 mm by 250 mm 

1 962a/01 

Function 

508 20 Nov 2011


LETTER PLATES AND LETTER BOXES (MAIL BOXES) 

The ‘Flaplock5’ helps to prevent the following when installed in accordance with the instructions contained on the 

document ‘FL05 FIT INST Rev 1’ and the flap is secured by inserting the pegs provided into the yolks located at 

both ends of the flap: 

- Insertion of litter, mail and other unwanted items into the property via the letter plate aperture. 

- Removal of keys and other items from within the property via the letter plate aperture1. 

- Access to locking hardware fitted to the door via the letter plate aperture by those attempting to gain 

unauthorised entry into the property by operating such hardware. 

Note 

1. It is recommended that such items are not stored within the immediate proximity of the letter plate. 

20 Nov 2011 509


KEY SAFES 

Key safes listed in this section are approved to LPS 1175 Requirements and testing procedures for the LPCB 

approval and listing of intruder resistant building components, strongholds, security enclosures and freestanding 

barriers. 

Unless otherwise stated, the security rating attributed to each key safe listed in this section relates to the key 

safes’ resistance to the following methods of attack: 

Forced entry into the key safe to remove a key stored within it. 

Unauthorised removal of the key safe from the supporting substrate. 

It is recommended that the security ratings of the key safes used to store keys are at least equivalent to those 

of the products (e.g. doorsets) the keys operate. This is particularly important if the key safes are located in 

unprotected areas, for example, on the outside of properties. This is to ensure the key safes do not 

compromise the resistance to forced entry provided by the products that the keys operate. 

UTC Fire & Security B.V. 

Kelvinstraat 7, 6003 DH, Weert, The Netherlands 

Tel: +31 495 583000 • Fax: +31 495 550042 

E-mail: esther.franken@fs.utc.com 

Europe, Middle East, Africa sales: 

UTC Fire & Security, Supra Asset Protection Solutions, Kouterveldstraat 2, B-1831 Diegem, Belgium 

Tel: +32 478 98 32 81 

E-mail: didier.trehout@fs.utc.com 

UK sales: 

Supra UK Ltd, 24 The Furlong, Berry Hill Industrial Estate, Droitwich Spa, Worcestershire WR9 9AH, United 

Kingdom 

Tel: +44 (0)1905 770333 

E-mail: sales@keysafe.co.uk 


Key Safes 

Product Name Model Part 

No. 

Instructions 

Supra P500 Wall mounted key safe with twelve button 002045 P/N10102761P1 

combination 

December 2009 

Supra Consumer 500 Wall mounted key safe with twelve button 002049 P/N10102770P1 

combination 

December 2009 

Supra P500 with Wall mounted key safe with twelve button 002046 P/N10102761P1 

alarm switch 

Supra Consumer 500 

with alarm switch 

combination incorporating an alarm switch 

Wall mounted key safe with twelve button 

combination incorporating an alarm switch 

December 2009 

002050 P/N10102770P1 

December 2009 


Rating No. 

1 976a/01 

1 976a/02 

1 976a/03 

1 976a/04 

Notes: 

1. The Supra key safes are approved when mounted directly to masonry walls in accordance with the instructions noted in the above 

table. The approval does not cover the key safes when mounted to alternative substrates or via intermediate substrates such as 

plasterboard. 

510 20 Nov 2011


SECURITY GLAZING 

This section includes security glazing that has been approved to one or more of the following standards: 

LPS 1270: Issue 1 Requirements and testing procedures for the LPCB approval and listing of intruder 

resistant security glazing units 

BS EN 356: 2000 Glass in Building - Security Glazing - Testing and classification of resistance against 

manual attack 

BS EN 1063: 2000 Glass in building. Security glazing. Testing and classification of resistance against 

bullet attack. 

LPS 1270 was developed because it was considered the method for classifying the attack resistance of 

security glazing specified within the current European standard (BS EN 356: 2000) was incompatible with that 

employed within LPS 1175: Issue 7 Requirements and testing procedures for the LPCB approval and listing of 

intruder resistant building components, strongpoints, security enclosures and free-standing barriers. This was 

because: 

BS EN 356: 2000 does not classify glass according to its resistance to different levels of attack based on 

the tools and time available to an intruder. 

The tests contained within BS EN 356: 2000 do not evaluate the glass’s susceptibility to attacks involving 

the creation of small holes through which locking hardware may be manipulated and/or protected items, 

such as items on display within shop windows or display cases, may be removed. 

Glazing materials rated to BS EN 356: 2000 that have previously been included within products and 

systems submitted for testing to LPS 1175: Issue 7 has undermined those product’s/system’s ability to 

offer intruder resistance commensurate with the security ratings sought to LPS 1175: Issue 7. 

The LPS 1270 classification system contains three digits. Each digit describes the glazing’s resistance to 

creation of a different size of hole, as described in the table below. 

Digit Type Tests block 

1 Local 

penetration 

3 Complete 

access 

8 mm (+3 mm/-0 mm) by 

25 mm (+3 mm/-0 mm) 

rectangular section 

2 Hand hole 60 mm (+3 mm/-0 mm) 

diameter 

Elliptical section of 400 mm 

(+3 mm/-0 mm) major axis 

by 225 mm (+3 mm/-0 mm) 

minor axis 

Notes 

Represents the glazing’s likely resistance to creation of a 

hole through which a piece of wire, screwdriver, lever or 

other such device can be passed. Such an attack may be 

attempted by an intruder wishing to operate a panic bar, 

emergency lever handle or other non-deadlocked device 

capable of releasing the boltwork on the item in which the 

glazing is mounted or on an item directly adjacent to that 

in which the glazing is mounted. 

Represents the glazing’s likely resistance to creation of a 

hand hole. Such an attack may be attempted by an 

intruder wishing to: 

• Operate a thumbturn to release the boltwork on the 

item in which the glazing is mounted or on an item 

directly adjacent to that in which the glazing is 

mounted. 

• Retrieve an item from the protected side of the glass, 

e.g. an item on display behind a shop window, a set of 

door keys or a set of car keys. 

This reflects the size of aperture specified in LPS 1175: 

Issue 7. The digit confirms the glazing’s resistance to 

creation of a hole through which an elliptical test block 

measuring 400 mm by 225 mm may be passed. This 

replicates the size a person may be able to pass through 

and reflects the test block defined in LPS 1175: Issue 7. 

The glazing’s resistance to creation of each size of hole will be indicated by a number (security rating) 0 to 8. 

The tools and time that the glazing must resist in order to achieve the security ratings match those that 

products classified in accordance with LPS 1175: Issue 7 must resist. The only difference is that glazing may 

20 Nov 2011 511


SECURITY GLAZING 

also achieve a ‘0’ rating in the first and second digits. Such a rating indicates the glazing’s resistance to the 

creation of those sizes of hole falls below that required to achieve security rating 1. 

The security ratings are loosely based upon domestic risks (security ratings 1 and 2), commercial risks (security 

ratings 2, 3 and 4), high security risks (security ratings 5 and 6) and extremely high security facilities (security 

ratings 7 and 8). 

In order to be classified to LPS 1270, glazing units must achieve a security rating of at least “001”. 

When selecting security glazing units it is important to consider other aspects of the product (e.g. window, 

doorset or curtain walling system) into which the glazing unit is to be fitted. In particular, it is important to 

consider the method by which the glazing unit is held in place. Manufacturers and specifiers should therefore 

ensure the complete product or system is assessed and classified in accordance with LPS 1175: Issue 7 

rather than simply the glazing. 

Essex Safety Glass Limited 

Units 1-3, Moss Road, Witham, Essex CM8 3UG, United Kingdom 

Tel: +44 (0)1376 520061 • Fax: +44 (0)1376 521176 

E-mail: sales@esguk.co.uk • Website: www.esguk.co.uk 


Laminated Security Glazing 

Product Name Type Nominal Total Thickness 

(mm) 

Nominal Weight 

(kg/m 2 

Security 

Rating 

Cert. 

No. 

ESG Secure LPS Laminated single glazing 

13 26.6 001 997a/01 

001/13 

unit 1, 2, 3, 4 


17 28.8 112 997a/02 

112/17 

unit 1, 2, 4, 5 


19 31.2 123 997a/03 

123/19 

unit 1, 2, 4, 5 


23 36 123 997a/04 

123/23 

unit 1, 2, 4, 5 


31 50.1 223 997a/05 

223/31 

unit 1, 2, 3, 4 


40 62.2 224 997a/06 

224/40 

unit 1, 2, 3, 4 


234/44 

ESG Secure LPS 

235/57 

1, 2, 4, 5 44 59.2 234 997a/07 

Laminated single glazing 

57.5 90 235 997a/08 

unit 1, 2, 3, 4 

Notes: 

1. The number within the product code indicating the thickness will be greater than that noted if thicker layers are used than those noted 

for the standard glazing units listed. 

2. The 4 mm toughened glass layer on the attack face of the glazing unit may be replaced by 4 mm float glass, 4 mm heat strengthened 

glass, 4 mm ‘ESG Pyrotech’ glass or 6 mm ‘ESG Pyrotech’ glass. However, these options may affect the nominal thickness and 

weight noted for this ‘ESG Secure’ glazing unit. 

3. The 4 mm float glass layer on the non-attack face of the glazing unit may be replaced by thicker float glass up to 19 mm, toughened 

glass between 4 mm and 19 mm thick, heat strengthened glass between 4 mm and 19 mm thick, 4 mm ‘ESG Pyrotech’ glass or 6 mm 

‘ESG Pyrotech’ glass. However, these options may affect the nominal thickness and weight noted for this ‘ESG Secure’ glazing unit. 

4. As an alternative to the single glazing units, Essex Safety Glass Limited also supply double glazed units (DGUs) formed using the 

glazing units approved to LPS 1270. The DGU’s are formed by adding a layer of float glass, toughened glass, heat strengthened 

glass or ‘ESG Pyrotech’ glass to the non-attack face. These are separated from the glazing units listed above by a spacer between 6 

mm and 22 mm thick. The DGUs are therefore thicker and heavier than the ‘ESG Secure’ single glazing units listed above. The 

product codes for ‘ESG Secure’ DGUs include the letters DGU immediately before the unit’s total thickness. For example, the ‘001/11’ 

unit with a 6 mm spacer and 4 mm toughened glass on the non-attack side of the DGU would have a code ‘001/DGU21’. 

5. The 4 mm toughened glass layer on the non-attack face of the glazing unit may be replaced by thicker toughened glass up to 19 mm, 

float glass between 4 mm and 19 mm thick, heat strengthened glass between 4 mm and 19 mm thick, 4 mm ‘ESG Pyrotech’ glass or 

6 mm ‘ESG Pyrotech’ glass. However, these options may affect the nominal thickness and weight noted for this ‘ESG Secure’ glazing 

unit. 

512 20 Nov 2011

Part 

5 

CONSTRUCTION 

PRODUCTS

PART 5: CONSTRUCTION PRODUCTS 

INTRODUCTION 

The products listed in this part of the Red Book have been assessed for ‘Technical Approval’ (or Certification) 

based on the intended use of the product, and take into account the UK Building Regulations, Highways 

Regulations, the Essential Requirements from the Construction Products Directive (CPD) and other directives 

as necessary. 

Most of the approvals listed are for products and systems for which there are no directly applicable recognised 

standards and a Technical Approval certification has been granted. Where British, European or other 

recognised standards apply, we also approve products against these standards. 

The granting of certification depends on the type testing and initial factory assessments meeting the relevant 

standards and scheme requirements laid down. Certification is maintained by regular factory production 

control surveillance visits and, where specified, the testing of audit samples to ensure that the product 

continues to be made in exactly the same way. 

IMPORTANT 

We are currently changing the way that we approve and certificate products with the result that we will not be 

issuing any new Technical Approvals. In the future, new certificates will issued against published BRE 

Schemes and, where appropriate BRE Product Standards (BPS). Details of current Schemes and associated 

BPSs can be found at: www.RedBookLive.com 

This does not affect the validity of the current Technical Approvals listed in this section. These will 

remain valid for three years from their date of issue - or until converted into one of our new range of 

Approved Building Product certificates. 

514 20 Nov 2011


ANCHORS, CONNECTORS, FASTENERS AND FIXING SYSTEMS 

The scope of products approved under this section is as follows: 

Anchors, connectors, fasteners and fixing components and systems manufactured from metals and plastics 

for providing mechanical jointing between components, or to fix to substrates of concrete, masonry, metal, 

timber and plastics, for building and construction products and kits over a specified design life. 

Max Frank Limited 

Whittle Road, Meir, Stoke-on-Trent, Staffordshire ST3 7HF, United Kingdom 

Tel: +44 (0)1782 598041 • Fax: +44 (0)1782 315056 

E-mail: info@maxfrank.co.uk • Website: www.maxfrank.co.uk 

Certificate No: 136/07 Rev Oct 10 


Shearail punching shear 

reinforcement 

Shearail punching shear reinforcement has been assessed to confirm its suitability, within 

limitations, for use as a punching shear reinforcement in reinforced concrete floor and 

roof slabs in buildings. The product comprises a set of forged steel studs (smooth or 

ribbed) connected at one end to a steel rail which is used to position them in the 

construction prior to placement of structural concrete. The product is available in a range 

of stud sizes. Studs are welded to the rails at predetermined spacing. Shearails are 

produced to meet specific project requirements. The minimum number of studs on a rail 

is two. 

Cert. No. 

136/07 

Rev Oct 

10 

20 Nov 2011 515


DRAINAGE AND PLUMBING SYSTEMS 


Drainage and plumbing products, systems and kits for domestic, commercial and industrial building 

applications manufactured from clay and cementitious based materials, plastics, metals and composites to 

provide for transfer and containment of potable and foul water, rainwater, sewage and effluent over a 

specified design life. 

516 20 Nov 2011


FLOORING SYSTEMS 


Flooring products, systems and kits for floor bases and floor finishes for domestic, commercial and industrial 

building applications manufactured from gypsum, clay and cementitious based materials, plastics, timber, 

metals and composites to provide support for loading, decoration and thermal, acoustic and fire protection 

over a specified design life. 

Intelligent Engineering (UK) Ltd 

Shire House, West Common, Gerrards Cross, Slough, Bucks SL9 7QN, United Kingdom 

Tel: +44 (0) 1753 890 575 • Fax: +44 (0) 1753 899 056 

E-mail: turner@ie-sps.com • Website: www.ie-sps.com 

Certificate No: ABP008 to BPS7007 


Flooring System - 

permanent and temporary 

stadium risers 

SPS Terraces are individual step units which are joined together one above the other in 

sets of four to form terraces. Each step unit consists of a horizontal sandwich panel 

(4mm steel faceplates with a 20mm high density (≥1000kg/m 3 ) polyurethane core) 

welded to steel plate risers. Connections between individual step units are made with 

proprietary fasteners which are also used to fix steel bracing and closing plates to 

completed terraces. 

SPS Terraces are available with a horizontal step width of 830mm and riser heights of 

178mm (7”) and 365mm (14”). Terraces consisting of four step units having a maximum 

length of 10m are supported on a braced steel perimeter frame. A steel closing plate is 

fixed immediately beneath the risers angled to the rake of the terrace. 

Cert. No. 

ABP008 

 

 

Steel is specified as S235 in accordance with BS EN 10025 Hot rolled products of 

structural steels. 

The polyurethane core is produced from polyol and isocyanate 

Fire resistance is achieved by the addition of fire protection using stone mineral wool 

insulation board (see table 3) fixed beneath the completed terraces. 

SPS Terraces are intended for use in permanent and temporary grandstand structures in 

the UK. The individual step units are connected together to form terraces in such a way 

that they can be dismantled and reassembled at another location. 

Certificate No: 154/11 


SPS Bubble Core Floors 

SPS (Sandwich Plate System) Bubble Core Floors are built up from a number of 

individual SPS Plates laid side by side and fixed to supporting steel located under each 

longitudinal joint in the direction of span. SPS Plates are of sandwich construction and 

comprise upper and lower steel plates bonded to a voided polyurethane elastomer core. 

Voids in the core are formed by the inclusion of hollow polypropylene spheres (nominal 

50mm diameter). The structural performance of the SPS Bubble Core Floor is achieved 

by the composite action of the SPS Plates and the supporting steel beams. SPS Plate 

units are a maximum of 3m wide by 9m long. 

This certificate reports on the outcome of specified tests on defined construction 

configurations. It provides design data relating to that construction for use by structural 

engineers competent in the design of steel structures. 

The tested construction incorporated three 9m x 3m SPS Plates assembled to form a 9m 

x 9m floor supported on a perimeter framework of rolled steel sections with proprietary 

fabricated steel beams providing intermediate support at plate junctions (see Figure 1). 

The SPS Plates were each 60mm thick, having a 50mm core sandwiched between two 

5mm steel plates. 

Fire protection shall be provided by means of stone mineral wool insulation board fixed 

immediately beneath the SPS Plates and supporting steel beam construction. 

The laboratory airborne and impact (acoustic) performance of the system has been 

determined for a number of different configurations. 

Cert. No. 

154/11 

20 Nov 2011 517


FLOORING SYSTEMS 


Cert. No. 

The characteristics of the product and its method of application have been reviewed with 

respect to the current Building Regulations, British and European Standards and other 

publications in the United Kingdom in February 2010. 

518 20 Nov 2011


GROUNDWORKS AND FOUNDATION SYSTEMS 


Groundworks and foundation products, systems and kits for domestic, commercial and industrial building 

applications manufactured from clay and cementitious based materials, plastics, timber, metals and 

composites to provide support for loading, water and gas resistance and thermal and fire protection over a 

specified design life. 

Cordek Limited 

Spring Copse Business Park, Slinfold, West Sussex RH13 0SZ, United Kingdom 

Tel: +44 (0)1403 799600 • Fax: +44 (0)1403 791718 

E-mail: sales@cordek.com • Website: www.cordek.com 



Ventform Panels 

Ventform panels have been assessed to confirm their suitability for use as a ventilation 

void former for the support of cast in-situ concrete slabs for either suspended or ground 

supported floors and to facilitate ventilation of hazardous gases. Ventform panels also 

provide insulation to improve thermal performance of ground floor construction. 

Cert. No. 

031/96 

Saint-Gobain Weber Limited 

Dickens House, Enterprise Way, Flitwick, Beds MK45 5BY, United Kingdom 

Tel: +44 (0) 1525 722101 • Fax: +44 (0) 1525 718988 

E-mail: mick.lovell@netweber.co.uk • Website: www.netweber.co.uk 



Weber Leca Insulation Fill 

Weber Leca Insulation Fill has been assessed to confirm its suitability, within limitations, 

for use as an insulation and hardcore material below ground floors. The product is a 

graded lightweight expanded clay aggregate. In a construction it is overlaid with a 

specified waterproofing membrane and stabilising wire mesh layer (both items not 

covered by this certificate). 

Cert. No. 

052/98 

20 Nov 2011 519


MEMBRANES 


Membranes for buildings manufactured from polymers, bitumen, rubbers and metal foil in liquid applied or 

sheet form for use as continuous or discontinuous layers for the control of the movement of air, liquid water, 

water vapour, carbon dioxide, radon and methane through floor, wall, roof and internal elements of buildings 

and structures over a specified design life. 

DuPont de Nemours (Luxembourg) S.a.r.l. 

Rue General Patton, L-2984, , Luxembourg 

Tel: +352 3666 5736 

E-mail: jimmy.helfenstein@lux.dupont.com • Website: www.tyvek.co.uk 



Tyvek® UV Facade 

Underlay 2524B 

Tyvek® UV Facade Underlay 2524B is intended to be used in Façade construction as a 

secondary, water vapour permeable, weather resistant layer, for protection against wind 

driven rain or snow and the ingress of dust. It has been designed for use with open or 

ventilated cladding constructions. 

Tyvek® UV Facade 2524B is a UV and heat stabilised Type LR low resistance 

(breathable) polymeric underlay as defined in BS 5250 Code of practice for the control of 

condensation in buildings. It comprises a 2 layer laminate of high density polyethylene, 

and a polypropylene fleece. Tyvek® UV Facade 2524B is embossed black on the outer 

surface (as installed) and white on the inner surface. 

Cert. No. 

155/10 



Tel: +44 (0)1347 825200 • Fax: +44 (0)1347 825222 

E-mail: info@itpltd.com • Website: www.itpltd.com 



Powerbase MB 420 Gas 

Resistant Membrane 

Powerbase MB 420 has been assessed to confirm its suitability for use as a gas and 

moisture resistant barrier for incorporation into the floor of a building to restrict the 

ingress of radon, methane and carbon dioxide from the ground in situations where there 

is a risk of contamination to the internal environment of the building. 

Cert. No. 

095/02 



Powerlon UltraPerm 

Breather Membrane 

Powerlon UltraPerm Breather Membrane (Powerlon UltraPerm BM) has been assessed 

to determine that it can be used, with conditions, as a roof underlay for use in pitched 

warm and cold roof constructions with or without ventilators, as a secondary weather 

resistant layer, for protection against wind driven rain and snow, tile wind-uplift, and 

ingress of dust to satisfy or contribute towards satisfying the requirements of the Building 

Regulations within the United Kingdom and Ireland. Powerlon UltraPerm BM consists of 

a water resistant and breathable polypropylene film sandwiched between two 

polypropylene spunbonded layers and is a permeable low vapour resistance (type LR) 

roof underlay as defined by BS 5250 Code of practice for the control of condensation in 

buildings. It is available in different weights, between 85g/m 2 and 140g/m 2 . 

Cert. No. 

124/07 

520 20 Nov 2011


MEMBRANES 

Klober Limited 

Unit 6F, East Midlands Distribution Centre, Short Land, Castle Donington, Derbyshire DE74 2HA, United 

Kingdom 

Tel: +44 (0)1332 813050 • Fax: +44 (0)1332 814033 



Sepa® forte 

Sepa ® forte is a reinforced multi-layer membrane and is blue in colour on the upper side. 

It is suitable, within conditions, as a roof underlay for use in pitched roof construction, 

under slates or tiles as a secondary weather resistant layer, for protection against winddriven 

rain and snow, tile wind-uplift and ingress of dust. The underlay has good 

resistance to tearing during installation and remains flexible at low temperatures. 

Cert. No. 

105/03 

Certificate No: ABP013 to BPS 7005 Issue 1.0 


Sepa Light 

Sepa Light is a UV and heat stabilised Type HR polymeric roof underlay. It comprises a 

polypropylene non-woven layer which is coated on one surface with a continuous film of 

polyethylene/polypropylene blend and is regarded as a high water vapour resistance 

(Type HR) underlay as defined in BS 5250 Code of practice for the control of 

condensation in buildings . Sepa Light is manufactured in rolls as shown below. 

Cert. No. 

ABP013 

Product dimensions CharacteristicNominal value Roll length 25 and 50 m Roll 

width1.0, and 1.5 m 

Sepa Light is dark grey with the brand name and unique production code printed on the 

upper surface (as installed) and blank on the lower surface. 

Sepa Light is intended to be used in pitched roofs as a secondary, impermeable, weather 

resistant layer, for protection against wind driven rain or snow and the ingress of dust. It 

is installed beneath roof tiles or slates in roofs constructed in accordance with BS 5534 

Code of practice for slating and tiling (including shingles). 

Visqueen Building Products 

Maerdy Industrial Estate, Rhymney, Tredegar NP22 5PY, United Kingdom 

Tel: +44 (0)1685 840672 • Fax: +44(0)1685 842580 

E-mail: enquiries@visqueenbuilding.co.uk • Website: www.visqueenbuilding.co.uk 



Visqueen Radon 

Membrane 

Visqueen Radon Membrane polyethylene sheet membrane has been assessed to 

confirm its suitability for use as part of a radon gas and moisture-resistant system for 

incorporation into the floor of a building in situations where there is a risk of 

contamination to the internal environment of the building arising from radon evolution 

from the ground. 

Cert. No. 

083/01 



Visqueen Eco-membrane 

Visqueen Eco-membrane re-cycled low density polyethene sheet membrane has been 

assessed to confirm its suitability for use as a damp proof membrane for incorporation 

into the floor of a building in situations where there is a risk of damage to the internal 

environment of the building arising from moisture from the ground. 

Cert. No. 

112/04 

20 Nov 2011 521


PRE-FABRICATED BUILDING SYSTEMS 


Building systems and kits of superstructure, basement and roofing structure for buildings as products, 

components and systems of wall, floor, roof and stairways, linings and finishes manufactured from gypsum, 

clay and cementitious based materials, plastics, timber, metals and composites for domestic and commercial 

applications over a specified design life. 

Kingspan Limited (t/a Profiles and Sections) 

Sherburn, Malton, North Yorkshire YO17 8PQ, United Kingdom 

Tel: +44 (0)1944 712000 • Fax: +44 (0)1944 710555 

E-mail: enquiries@kingspanprofiles.com • Website: www.kingspanprofiles.com 



Kingframe Building and 

Architectural Façade 

System 

The Kingframe Building and Architectural Façade Systems have been assessed to 

confirm suitability for use as building structures (KBS) and as infill construction to form 

external facades to steel or concrete framed single and multi storey buildings (AFS). 

The Kingframe Building System (KBS) comprises; load-bearing steel stud external wall 

frames incorporating specified insulation, load-bearing and non load-bearing internal wall 

frames incorporating specified insulation, steel and timber cassette floor panels, 

composite concrete floors and steel and timber cassette roof panels. 

The Architectural Façade System (AFS) comprises; non load-bearing steel stud wall 

frames incorporating specified insulation. 

The characteristics of the systems covered by this certificate are: 

Cert. No. 

118/06 

 

 

 

 

 

 

 

 

Structure 

Behaviour in relation to fire 

Weathertightness 

Thermal transmittance and condensation risk 

Acoustic performance 

Durability 

Factory production and quality control 

Practicality of site installation 

The KBS and AFS systems are installed by Kingspan Ltd trained and approved installers. 

The KBS and AFS systems have been assessed for use with masonry, render, brick slip, 

rainscreen, timber and stone claddings (outside the scope of this certificate) which are 

not supplied by Kingspan Ltd but for which performance assessments have been made 

in relation to use with the KBS and AFS systems. 

The characteristics of The Kingframe Building and Architectural Façade Systems have 

been reviewed with respect to the current Building Regulations, British and European 

Standards and other publications in the United Kingdom and Ireland in January 2011. 

Metsec Limited 

Broadwell Road, Oldbury, West Midlands B69 4HE, United Kingdom 

Tel: +44 (0)121 601 6000 • Fax: +44 (0)121 601 6126 

E-mail: metsecframing@metsec.com • Website: www.metsec.com 



Metframe and SFS Building 

System 

The Metframe and SFS Building Systems have been assessed to confirm suitability, 

subject to the limitations of this certificate, for use in the construction of residential and 

commercial buildings in the UK with a floor no more than 18m from the ground unless 

Cert. No. 

110/04 

522 20 Nov 2011


otherwise stated in this certificate 



Cert. No. 

The loadbearing system either arrives on site in pre-made panels (Metframe) where 

connections are predominately bolted or is ‘stick-built’ on site (SFS) with connections 

predominately screw fixed. The non-loadbearing system (SFS) is ‘stick-built’ on site using 

screw fixed connections and is used to form non-loadbearing external walls in traditional 

superstructures. 

The Metframe and SFS Building Systems included within the scope 

of this certificate are listed below along with the materials or 

products (outside the scope of this certificate) for which the 

performance of the Metframe and SFS building systems have been 

assessed in typical building applications. 

Intermediate/separating floors: 

Cold formed galvanised steel Z-purlins 

Profiled metal decking to support in-situ poured concrete* 

Under cladding with 80mm Isowool 1000 insulation* 

Two 12.5mm layers of British Gypsum Fireline Board* 

Either over cladding with 5mm Ethafoam and 50mm 

concrete screed or 

Isolgomma R10 and 19mm Viroc board*. 

Cold-formed galvanised steel joists 

75mm Isowool 1605 located between the joists* 

Under cladding with defined combinations of British Gypsum Wall and Fireline 

Boards* 

External wall panels (load bearing and non-load bearing): 

Cold-formed galvanised steel stud (SFS) and pre-fabricated panels (Metframe) 

Defined combinations of British Gypsum lining boards, cement particle board 

and Thermawall TW55 insulation board* 

Isowool Hitherm insulation between the studs. The panels form the inner leaf 

of a wall having a 50mm cavity* 

Outer leaf of conventional masonry construction* 

External wall panels (load bearing and non-load bearing): 

Cold-formed galvanised steel stud (SFS) and pre-fabricated panels (Metframe) 

Defined combinations of British Gypsum lining boards, cement particle board 

and Thermawall TW55 insulation board* 

Isowool Hitherm insulation between the studs. The panels form the inner leaf 

of a wall having a 50mm cavity* 

Outer leaf of conventional masonry construction* 

Internal wall panels (load bearing and non-load bearing): 

Cold-formed galvanised steel stud panels 

Defined combinations of British Gypsum lining boards*. 

Isowool 1000, 1200 and 1605 insulation between the studs*. 

* Materials/products supplied by others and outside the scope of this certificate 

The Metframe and SFS Building Systems which are designed on a site and project 

specific basis, are used with other building elements and products, that are supplied by 

others, to deliver specific building requirements. The design verification shall be carried 

out by a suitably qualified and experienced Metsec plc engineer and comply with relevant 

structural regulations, codes and standards in force in the UK at that time and including 

the Metsec plc Technical Manual. The structural adequacy of the Metframe and SFS 

Building Systems, including connection and foundation design, have not been assessed 

by BRE Certification as the design verification will be site and project specific. 

The characteristics of the system elements covered by this certificate are: 

Behaviour in relation to fire 

Weathertightness 

Thermal transmittance and condensation risk 

Acoustic performance 

Durability 

Factory production and quality control 

Practicality of site installation (with reference to Metsec plc Technical Manual). 

The structural adequacy of the Metframe and SFS building systems, including foundation 

design, has not been assessed by BRE Certification. 

The Metframe and SFS Building Systems are installed by Metsec plc Approved Installers. 

20 Nov 2011 523




Cert. No. 

The performance of the system depends on the quality of its installation. Whilst the 

installation manual has been examined by BRE Certification and a site installation 

observed to confirm that the system can be assembled satisfactorily following those 

installation instructions, the actual quality of installation achieved on specific sites is not 

covered by this certificate. The systems shall be installed by appropriately trained and 

experienced Metsec plc Approved Installers. 

When used as part of the external wall construction to framed superstructures (i.e.Timber 

BS 5268 Structural use of timber; Masonry BS 5628 Code of practice for the use of 

masonry, Steel BS 5950 Structural use of steelwork in building; Concrete BS 8110 

Structural use of concrete with a masonry external surface (i.e. BS EN 771-1:2003 

Specification for masonry units. Clay masonry units or previously BS 3921 Specification 

for clay bricks) the non-loadbearing SFS system may be used in buildings with a floor 

more than 18 metres from the ground. 

The load bearing site-built stick system (SFS) shall not be used for constructions over 3 

storeys in height. 

Characteristics of the Metframe and SFS Building Systems have been reviewed with 

respect to the current Building Regulations, British and European Standards and other 

publications in the United Kingdom in April 2010.The assessment is described in the 

following pages, which form integral parts of this certificate and should be read in their 

entirety. 

524 20 Nov 2011


BUILDING SYSTEMS FOR DWELLINGS 

BRE Global has developed the BPS 2020 suite of standards to provide for approval of building systems for 

dwellings. The primary objective of this approval scheme is to encourage innovation whilst maintaining 

acceptable levels of safety and to create confidence in the development and use of building systems for 

dwellings, particularly those using Modern Methods of Construction (MMC). 

Fusion Building Systems 

Fusion House, Scirocco Close, Moulton Park, Northamptonshire NN6 3HE, United Kingdom 

Tel: +44 (0)1604 490540 • Fax: +44 (0)1604 490549 

E-mail: Tom.Salvesen@fusionbuild.com • Website: www.fusionbuild.com 

Certificate No: ABP006 to BPS2020 


Fusion Building System 

The Fusion building system is a panelised light gauge steel building system for the 

construction of dwellings up to 6 storeys in height, and as the upper six storeys of a 

building which has a top floor height not more than 30m above ground level. In buildings 

with a traditional pitched roof no floor shall be more than 18m above ground level. The 

system comprises the following principal building elements. 

External Walls - the inner leaf of external walls consists of factory made loadbearing cold 

rolled light gauge steel sections with flame retardant expanded polystyrene insulation 

moulded into the body of the panel and forming an external layer to provide a hybrid 

construction. The Fusion building system has been assessed for use with conventional 

masonry cladding and specified internal plasterboard lining. 

Internal Walls - load bearing walls are formed using cold rolled light steel panels as 

described for external walls. Separating walls consist of two load bearing panels 

separated by a cavity with gable apex panels used in pitched roofs. 

Floors - upper floors are either of factory built cassette form using C section steel joists 

and steel channel rim sections covered with oriented strand board or site assembled, 

using C section steel joists supported at the ends by steel Z sections and covered with 

oriented strand board. Separating floors are designed as compartment floors and 

incorporate additional proprietary material to provide fire resistance and acoustic 

performance. Composite concrete/steel deck floors have also been assessed for use with 

the Fusion building system. 

Roofs - flat roofs are of factory built floor cassette form (as floors) suitable to support 

proprietary warm deck roof systems or traditional proprietary timber trussed rafter roofs. 

Cert. No. 

ABP006 

Key Housing Limited 

2 Sebastian Street, London EC1V 0HE, United Kingdom 

Tel: +44 (0)20 7687 6004 • Fax: +44 (0)20 7687 6002 

E-mail: kahn@key-housing.co.uk • Website: ww.key-housing.co.uk 

Certificate No: ABP 010 to BPS 2020 


Key Housing Building 

System 

The Key Housing building system is a volumetric steel framed building system for the 

construction of dwellings up to 6 storeys in height with floors up to 18m above ground 

level. The system comprises the following principal building elements. 

External Walls - Factory made insulated loadbearing volumetric building pods forming the 

inner leaf of external walls assembled from a combination of hot and cold rolled light steel 

C sections, (of various material thickness up to 3mm) with mineral fibre insulation. An 

internal lining of one or more layers calcium silicate board is added to provide the 

required period of fire resistance and a surface finish. External faces are lined with fibre 

cement boards. The volumetric modules incorporate brackets allowing steel wall ties to 

be fitted on site to tie external cladding systems to the Key Housing external wall panel. 

Cert. No. 

ABP 010 

20 Nov 2011 525




The backing wall does not rely on the exterior cladding to provide water resistance and 

has been designed to accommodate a number of cladding systems. BRE report 267-819 

provides information on the use of typical insulated render, brick skin and terracotta tile 

rainscreen applications which are outside the scope of the certificate. 

Internal Walls - load bearing walls are formed using cold rolled steel C sections. 

Separating walls incorporate a cavity and are formed by placing two steel C section 

panels adjacent to one another. Walls incorporate mineral fibre insulation and are lined 

on room faces with calcium silicate board. 

Floors - Upper floors are of factory built volumetric pod construction, the floor surface 

and supporting steel joists are part of the upper pod and the ceiling below is formed by 

the lower pod. Separating floors are designed as compartment floors and incorporate 

additional proprietary material, including calcium silicate board, to provide fire resistance 

and acoustic performance. 

Roof - Roof structures are formed by the top of the upper pod, used to form a flat roof 

structure (suitable to support a warm deck roof system outside the scope of the 

certificate) or a traditional pitched roof (formed of roof trusses with cladding, which is 

outside the scope of the certificate). 

Cert. No. 

SIP Energy Ltd 

Athenry, , Co Galway, Ireland 

Tel: +353 (0)91 874290 • Fax: +353 (0)91 874295 

E-mail: info@sip-energy.com • Website: www@sip-energy.com 

Certificate No: ABP 005/001 to BPS2020 


SIP Energy Structurally 

Insulated Panel System 

The SIP Energy Structurally Insulated Panel System (incorporating structurally insulated 

wall and roof panels) is a factory produced structurally insulated panel (SIP) system for 

the construction of dwellings up to 3 storeys in height. The system, shown in figures 1 to 

5, comprises the following principal building elements; 

1.1 External Walls - load bearing factory assembled wall panels comprising timber 

studs, OSB facings and extruded polystyrene insulation, bonded together by 

polyurethane adhesive. The key components of these panels are: 

- 15mm OSB sheathing 

- 100mm* internal timber stud framing** with XPS (Extruded Polystyrene) insulation infill 

between 

- 15mm OSB sheathing 

The panels are erected and fixed together on site using power driven 2.8mm by 63mm 

ringshank nails and screws. Preservative treated timber plates, bolted to the 

substructure, are used for accurate positioning and levelling. Panels interlock with 

adjacent panels and with location plates to provide a positive connection which is also 

sealed by application of sealant during installation. The walls have a breather membrane 

and conventional masonry cladding (provided by others) externally with a 50mm drained 

and vented cavity. Any other external cladding is outside the scope of this certificate. An 

internal lining of plasterboard is added (by others) to provide the required period of fire 

resistance and a surface finish. 

* Panels with thicker insulation are available 

** Preservative treated timber can be used if requested. 

1.2 Internal Walls - load bearing walls can be formed using the panels as described for 

external walls. Compartment walls between adjacent dwellings consist of two panels 

separated by a cavity as shown in Figure 5 

1.3 Floors - floors are formed using conventional components such as I section joists 

with OSB decking. The OSB deck can be carried over the head of wall panels below to 

provide a connection to the wall. See figure 1 

1.4 Roof - roofs can be formed using similar panels to the walls (with 125mm thickness 

insulation infill) or by using conventional roof trusses. When SIP Energy panels are used 

they are inclined to provide support to the roof underlay and battens which support the 

tile covering. A timber or steel beam (outside the scope of this certificate) is used to 

support the roof panels at the ridge. See figure 1 

Cert. No. 

ABP 

005/001 

526 20 Nov 2011




Cert. No. 

1.5 Other items - Other items typically supplied with the SIP Energy system include 

DPCs, mineral wool insulation, cavity barriers, lining boards, acoustic sealant, ceiling 

battens, fixing plates, and foam sealant to fill joints. These are not covered by this 

certificate. 

The innovative elements covered by this certificate are: 

- The insulated wall panel which can also be used inclined to form a roof 

- Fixing brackets and straps for frame and foundation connections 

The non-innovative elements assessed for use with the above innovative elements 

- The internal wall and ceiling linings 

- Roof insulation applied between roof trusses 

- The timber based floor joists and decking 

- The masonry external wall cladding 

- The tile or slate roof cladding 

20 Nov 2011 527


TRUSSED RAFTERS (TIMBER) 

This scheme has now been withdrawn. 

528 20 Nov 2011


THERMAL INSULATION SYSTEMS 

The scope of products covered under this scheme is as follows: 

Thermal insulation products, systems and kits, with formed and formless materials, for domestic, commercial 

and industrial building applications manufactured from cellulose, mineral and natural fibre, clay and 

cementitious based materials, plastics, timber, metals and composites. These provide control of thermal 

movement through floor, wall, roof and internal elements of buildings, decoration, and weather resisting, fire 

and acoustic protection with and without mechanical and adhesive fixings, with continuous or discontinuous 

layers. 

Euroform Products Limited 

The Heliport, Lyncastle Road, Appleton, Warrington, Cheshire WA44 4SN, United Kingdom 

Tel: +44 (0) 1925 860999 • Fax: +44 (0) 1925 860066 

E-mail: sales@euroform.co.uk 



U Foil 1BD/A-1 Single Foil 

Bubble Insulation and U 

Foil 1BD/A Double Foil 

Bubble Insulation 

U Foil 1BD/A-1 (Single) and 1BD/A (Double) Foil Subble Insulation products have been 

assessed to confirm their suitability for use as insulation behind internal dry lining or for 

improving insulation to external cavity walls on the internal side of the weathering 

protection as partial fill cavity wall insulation for buildings with masonry or dense concrete 

walls. The products consist of aluminium foil faced polyethylene bubble film multilayer 

laminates. 

Cert. No. 

147/08 



U Foil VBF Vented Foil 

Bubble 

U Foil VBF Vented Foil Bubble is a reflective insulation and vapour open cavity rain 

barrier and has been assessed to confirm its suitability for use as a thermal isolating 

layer for improving insulation to external cavity walls of timber frame construction in the 

United Kingdom. The product consists of an aluminium foil faced polyethylene bubble film 

laminate. U Foil VBF Vented Foil Bubble is installed against the inner leaf sheathing 

withing the cavity within the foil face o the clear cavity side. 

Cert. No. 

148/08 

Yorkshire Building Services (Whitwell) Limited 

The Crags Industrial Estate, Morven Street, Creswell, Derbyshire S80 4AJ, United Kingdom 

Tel: +44 (0)8449910044 • Fax: +44 (0)8449910055 

E-mail: robertq@ybsinsulation.com • Website: www.ybsinsulation.com 



Products for Use in 

improving thermal 

insulation of walls & roofs 

Yorkshire Building Services (Whitwell) Limited (YBS) produce a range of products for use 

in improving the thermal insulation of walls and roofs. This certificate covers the products 

below; 

Therma Close - Insulated cavity closer and damp proof barrier for use around openings 

in masonry cavity walls. 

Therma Close Type R - Insulated cavity closer and damp proof barrier for use around 

openings in masonry cavity walls. 

Therma-Flect EPS and Therma-Flect PIR (Wall Boards) - Partial fill cavity wall insulation 

for improving thermal insulation in external walls of masonry. 

Therma-Flect EPS and Therma-Flect PIR (Roof Boards) - Combined thermal insulation 

and protection against wind driven rain and snow for use under slates or tiles at rafter 

Cert. No. 

157/11 

20 Nov 2011 529


THERMAL INSULATION SYSTEMS 


level. The bubble foil layer may be located above or below the rafter. 

Cavi-Mate EPS and Cavi-Mate Rock fibre cavity closers - Cavity closer providing a 

damp-proof barrier and thermal insulation for use around openings in masonry cavity 

walls. 

Cert. No. 

The characteristics of the products and their method of application have been reviewed 

with respect to the current Building Regulations, British and European Standards and 

other publications in the United Kingdom in November 2011. 

530 20 Nov 2011


WALL AND ROOF CLADDING SYSTEMS 


Wall and roof cladding products, systems and kits for domestic, commercial and industrial building 

applications manufactured from metals, plastics, timber, glass, natural stone, clay and cementitious based 

materials and composites to provide decoration, and weather resisting, fire, thermal and acoustic protection. 

Eurobrick Systems Limited 

Unit 7, Wilverley Trading Estate, Bath Road, Brislington, Bristol BS4 5NL, United Kingdom 

Tel: +44 (0)117 971 7117 • Fax: +44 (0)117 971 7217 

E-mail: info@eurobrick.co.uk • Website: www.eurobrick.co.uk 

Certificate No: 015/93 Reissue 2010 


Eurobrick Insulated Brick 

Cladding System 

The Eurobrick Insulated Brick Cladding System (Eurobrick System) comprises a 

composite backerboard formed from extruded polystyrene insulation board glued to a 

profiled polystyrene carrier sheet, brick slips, proprietary mortar and specified ancillary 

components. Finished walls have the appearance of traditional brickwork. Where 

specified a cavity can be incorporated into the construction behind the insulation by 

means of a supporting framework. This application is outside the scope of this certificate. 

The Eurobrick System supplied by Eurobrick Systems Limited (Eurobrick) has been 

assessed to confirm its suitability for use as a weather resistant, thermal insulating 

external decorative finish for application to external vertical walls of new or existing 

residential and commercial buildings of masonry, dense concrete, timber or metal frame 

construction. 

Cert. No. 

015/93 

reissue 

2010 

John Brash & Company Ltd 

The Old Shipyard, Gainsborough, Lincolnshire DN21 1NG, United Kingdom 

Tel: +44 (0)1427 613858 • Fax: +44 (0)1427 810218 

E-mail: info@johnbrash.co.uk • Website: www.johnbrash.co.uk 

Certificate No: ABP 003 to BRE Product Standard BPS 7002 Issue 1.0 


JB RED Roof tiling battens 

The JB RED Roof tiling battens are machine graded timber roof tiling battens with cross 

sectional dimensions of either 25mm x 38mm or 25mm x 50mm made from either 

European Redwood or Whitewood from a PEFC/FSC certified source. The battens are 

treated with a preservative specified to achieve a 60 year design life for the battens in 

accordance with BS 8417 and BS EN 599-1. The preservative supplier provides a 60 

year warranty. 

Individual battens are marked as follows: 

For 25mm x 38mm redwood battens: JOHN BRASH 25x38 PNSY BS5534 JBRED 

For 25mm x 50mm redwood battens: JOHN BRASH 25x50 PNSY BS5534 JBRED 

For 25mm x 38mm whitewood battens: JOHN BRASH 25x38 WPCA BS5534 JBRED 

For 25mm x 50mm whitewood battens: JOHN BRASH 25x38 WPCA BS5534 JBRED 

The battens are intended for use as part of a timber roofing structure to support concrete, 

clay, fibre-cement, natural slate or metal roofing tiles and/or bitumen or wooden shingles. 

The preservative treatment applied does not provide resistance to attack by the House 

Longhorn beetle. 

Cert. No. 

ABP 003 

20 Nov 2011 531



Marmorit (UK) GmbH 

1 Portview Road, Avonmouth, Bristol BS11 9LS, United Kingdom 

Tel: +44 (0)117 982 1042 

E-mail: enquiries@marmorit.co.uk • Website: www.marmorit.co.uk 



Marmorit Warm Wall 

Insulation Systems 

1) Warm-wall polystyrene tongue and grooved 

2) Warm-wall mineral fibre wool 

3) Warm-wall mineral fibre volamit 

4) Warm-wall rail system 

 

 

 

 

polystyrene tongue and grooved 

mineral fibre wool 

mineral fibre volamit 

rail system External Wall Insulation 

Marmorit Warm-Wall External Wall Insulation Systems are External Thermal Insulation 

Composite Systems (ETICS) and have been assessed to confirm their suitability for use 

as external decorative and thermal insulating systems for buildings of masonry or dense 

concrete walls in the United Kingdom. The systems consist of an insulant of expanded 

polystyrene boards or mineral fibre slabs with a range of cementitious based coloured 

coating finishes. The method of providing insulation and fixing to the substrate 

determines which of the Marmorit Warm-Wall systems is used. 

Cert. No. 

059/99 



Marmorit Render Systems 

Marmorit render systems (finish renders applied to a basecoat) have been assessed to 

confirm their suitability for use as a weather resistant external decorative coating on new 

and existing walls of either fired-clay brick, or of lightweight or dense aggregate concrete 

block, masonry or dense concrete construction or over existing rendering using these 

products. They are one coat or two coat ready coloured render system providing various 

surface textures and colours. 

Cert. No. 

081/01 

PermaRock Products Limited 

Jubilee Drive, Loughborough, Leicestershire LE11 5TW, United Kingdom 

Tel: +44 (0)1509 262924 

E-mail: info@permarock.com 



PermaRock External Wall 

Insulation System 

The system has been assessed to confirm its suitability as an external decorative and 

thermal insulating system for use on masonry, dense and no-fines concrete, timber frame 

or steel frame walls. It consists of an insulant of mineral wool or expanded polystyrene 

boards with a range of polymer modified render and aggregate finishes, or fired clay brick 

slips. 

Cert. No. 

029/95 



PermaRock Phenolic 

External Wall Insulation 

System 

The system has been assessed to confirm its suitability for use as an external decorative 

and thermal insulation system for masonry or concrete walls. The system consists of an 

insulant of phenolic foam and a range of polymer-modified render and aggregate 

finishes. 

Cert. No. 

041/97 

532 20 Nov 2011



Wienerberger Limited 

Wienerberger House, Brooks Drive, Cheadle Royal, Cheadle, Cheshire SK8 3SA, United Kingdom 

Tel: +44(0)161 491 8200 • Fax: +44(0)161 491 1270 

E-mail: office@wienerberger.co.uk • Website: www.wienerberger.co.uk 



Corium 

Corium has been assessed to confirm its suitability for use as an external weather 

resistant and decorative brick cladding for application to external vertical walls of new or 

existing buildings of masonry, dense concrete, timber or metal frame construction in the 

UK. The system consists of horizontally mounted steel channel profiles, fitted externally 

with brick clay tiles with mortar pointing, to provide a brickwork finish. 

Cert. No. 

082/01 

Z-Led Limited 

Plymouth Avenue, Brookhill Industrial Estate, Pinxton, Nottingham NG16 6NS, United Kingdom 

Tel: +44 (0)1773 814113 • Fax: +44 (0)1773 814115 

E-mail: info@z-led.com • Website: www.z-led.com 



Aluflash - coated 

aluminium flashing 

Aluflash is an aluminium based weathering flashing material. It comprises solvent lacquer 

coated embossed aluminium sheet material to BS EN 1396:2007 Aluminium and 

aluminium alloys. Coil coated sheet and strip for general applications. Specifications with 

a self-adhesive butyl backing for adhesion to roof coverings or masonry. It is available in 

flat or cross corrugated versions. 

Aluflash is intended for use fully supported as stepped, abutment, chimney and saddle 

flashings, to line valleys, box and secret gutters and at upstands to rooflights and solar 

panels. Cross corrugated Aluflash is intended for use where the flashing needs to be 

moulded over and around complex shapes. 

Cert. No. 

153/10 

20 Nov 2011 533


WALLING, ROOFING AND PARTITION SYSTEMS 


Walling, roofing and partition products, systems and kits for building and construction applications 

manufactured from gypsum, clay and cementitious based materials, plastics, timber, metals and composites 

to provide loadbearing or non loadbearing structures and finishes, decoration and weather resisting, fire, 

thermal and acoustic protection. 

Kingspan Limited (t/a Profiles and Sections) 


Tel: +44 (0)1944 712000 • Fax: +44 (0)1944 710555 

E-mail: enquiries@kingspanprofiles.com • Website: www.kingspanprofiles.com 



Kingspan Building and 

Architectural Façade 

Systems 

The Kingframe Building and Architectural Façade Systems have been assessed to 

confirm suitability for use as building structures (KBS) and as infill construction to form 

external facades to steel or concrete framed single and multi storey buildings (AFS). 

The Kingframe Building System (KBS) comprises; load-bearing steel stud external wall 

frames incorporating specified insulation, load-bearing and non load-bearing internal wall 

frames incorporating specified insulation, steel and timber cassette floor panels, 

composite concrete floors and steel and timber cassette roof panels. 

The Architectural Façade System (AFS) comprises; non load-bearing steel stud wall 

frames incorporating specified insulation. 

The characteristics of the systems covered by this certificate are: 

· Structure 

· Behaviour in relation to fire 

· Weathertightness 

· Thermal transmittance and condensation risk 

· Acoustic performance 

· Durability 

· Factory production and quality control 

· Practicality of site installation 

The KBS and AFS systems are installed by Kingspan Ltd trained and approved installers. 

The KBS and AFS systems have been assessed for use with masonry, render, brick slip, 

rainscreen, timber and stone claddings (outside the scope of this certificate) which are 

not supplied by Kingspan Ltd but for which performance assessments have been made 

in relation to use with the KBS and AFS systems. 

The characteristics of The Kingframe Building and Architectural Façade Systems have 

been reviewed with respect to the current Building Regulations, British and European 

Standards and other publications in the United Kingdom and Ireland in January 2011. 

Cert. No. 

118/06 

Logix UK Limited (Simplipac) 

57 Balena Close, Creekmoor Industrial Estate, Poole, Dorset BH17 7DG, United Kingdom 

Tel: +44 (0)1202 694 259 • Fax: +44 (0)1202 600 640 

E-mail: enquiries@logix.uk.com • Website: www.logix.uk.com 



Logix ICF Blocks 

Logix ICF blocks have been assessed to confirm, within limitations, their suitability as a 

permanent Insulating Concrete Formwork (ICF) system. The forms of the system can be 

partly assembled off site (panelised) or fully assembled on site (in-situ) to produce a 

Cert. No. 

122/06 

534 20 Nov 2011


WALLING, ROOFING AND PARTITION SYSTEMS 


permanent formwork (shuttering), which is filled with a defined concrete mix and steel 

reinforcement where required. The resultant concrete walls with expanded polystyrene 

(EPS) panels either side can be used as either load-bearing or non load-bearing 

insulated walls in residential or commercial buildings. Only walls where the height of the 

top floor above ground, in a building or separated part of a building is not more than 18m 

are covered by this certificate. 

The forms comprise of two EPS panels each having a thickness of 70mm. They are held 

apart at either: 100mm (Logix4), or 159mm (Logix6) or 203mm (Logix8) forms, by 

proprietary polypropylene ties moulded into the EPS panels at 203mm centres. The 

forms have a nominal height of 203mm (half height) or 406mm (full height). The lengths 

of the forms are typically 1219mm. The forms are produced in straight, 45 o or 90 o plan 

sections. Both internal and external faces of the finished walls require the addition of a 

protective cladding not covered by this certificate. 

The characteristics of the product and the method of application have been reviewed with 

respect to the Building Regulations current in the United Kingdom. The assessment has 

referred to British Standards and other publications current when this certificate was 

issued. 

Cert. No. 

20 Nov 2011 535


CONSERVATION OF FUEL AND POWER 

Products covered under this scheme have been demonstrated to aid the conservation of fuel and power in 

buildings. 

Energy Control Systems Ltd 

Pipsden Lodge, Rye Road, Hawkhurst, Kent TN18 5DN, United Kingdom 

Tel: +44 (0)1580 753682 

Website: www.energy-control-systems.no 

Distributed and Installed by Dynamic Energy Products Ltd 

Fig Tree House, Dymchurch Road, St Mary's Bay, Kent TN29 0HF, United Kingdom 

Tel: +44 (0)1797 367400 • Fax: +44 (0)1797 367400 

E-mail: thermsave@aol.com 

Certificate No: CFP 348 


Burner Management Unit 

BM1 and Dynamic Burner 

Management Unit DBMU 

The Burner Management is designed to modify the burner-firing pattern of conventional 

commercial boilers and water heaters (with 40kW input or greater) to minimise wasteful 

over-firing. The effectiveness of the Burner Management Unit has been tested on a 

typical open-flued commercial boiler (rated at 63kW) subject to a fully repeatable load 

pattern over a course of back-to-back tests with the Burner Management Unit both in and 

out of circuit. 

Cert. No. 

CFP 348 

536 20 Nov 2011

Part 

6 

MANAGEMENT SYSTEM 

CERTIFICATION

PART 6: MANAGEMENT SYSTEM CERTIFICATION 

Introduction 

We offer approval to the three key management system standards for: 

Quality - ISO 9001 

Now one of the world’s leading management system standards, ISO 9001 gives confidence to customers that 

the businesses they trade with have consistent levels of quality and service. 

Environmental Management - ISO 14001 

Approval to ISO 14001 demonstrates a company’s commitment to the environment and provides an 

assurance to the public, regulators and purchasers that its environmental policies and procedures are 

effective. 

Health and Safety - BS OHSAS 18001 

This is a specification that helps to fully integrate health and safety into company policies and working 

practices. It also signals to architects, clients, insurers and specifiers that a company takes its health and 

safety responsibilities seriously. 

As well as providing approval to each individually, we offer an integrated service to companies wanting 

approval under two or more of these management system standards. 

538 20 Nov 2011


QUALITY SYSTEMS 

Approval of a Quality Management System demonstrates that a company’s internal systems and processes 

are in place and operating as intended. It also measures performance in delivering products or services to an 

agreed standard. 

Third party approval is an independent review of a particular area of a company’s activities, which leads to 

improved processes and increased consumer confidence, and can help to reduce costs. Under the 

International Standard, ISO 9001, the certificate identifies which parts of a company’s activities are covered, 

and must include design if this is part of its operation. 

This scheme is for companies whose Quality Management Systems have been designed to meet the 

requirements of ISO 9001. For companies that already have a certificated Quality Management System 

assessed to ISO 9001, we offer approval of the factory production control processes applicable to the 

products we approve, and these are detailed in the entries listed where that option has been taken. 

The entries in this section define the scope of activities that have been assessed under the management 

system. 

Unlike our product approval schemes, which relate to specific products and services, Quality Management 

Systems approval can encompass the complete scope of a firm's activities at that particular address. 

However, it is important to understand that ISO 9001 does not provide an assurance to the user or specifiers 

that actual products or services conform to requirements, since no testing or cross checking of conformity to 

product or service standards is involved. Therefore, no marking of specific products or installations is 

permitted. 

For companies operating in the fire and security areas with LPCB product or service approvals, our ISO 9001 

approval is given in the name of LPCB. Where companies do not require LPCB product or service 

certification, then all certificates are issued in the name of BRE Global Limited. 

2M KABLO SAN. ve TIC. A.S. 

Sanayi Mahallesi, 1678 Sokak No: 3, 34511 Esenyurt, Istanbul, Turkey 

Tel: +90 212 672 7314 • Fax: +90 212 672 7312 

E-mail: sales@2mkab.com • Website: www.2mkab.com 

Also at: 

Perpa Ticaret Merkezi, A Blok Kat:8, No.707, Okmeydani, Istanbul, Turkey 

Quality System Cert. No. 711 Assessed to ISO 9001:2008 

Scope: 

Design and manufacture of electric cables for use in installations that require safety in the event of fire. 

A & F Sprinklers Limited 

Atrium House, 574 Manchester Road, Blackford Bridge, Bury, Lancashire BL9 9SW, United Kingdom 

Tel: +44 (0)845 505 1550 • Fax: +44 (0)845 505 1660 

E-mail: info@afsprinklers.co.uk • Website: www.afsprinklers.co.uk 


Scope: 

Design and installation of fire sprinkler and water spray systems. 

20 Nov 2011 539



A M Profiles Limited 

Hardwick View Road, Holmewood Industrial Estate, Holmewood, Chesterfield, Derbyshire S42 5SA, United 

Kingdom 

Tel: +44 (0)1246 856000 • Fax: +44 (0)1246 855105 

E-mail: sales@amprofiles.com 


Scope: 

Manufacturing and installation of architectural aluminium and composite glazing. 

A Steadman & Son 

(a division of SIG Trading Ltd), Warnell, Welton, Carlisle, Cumbria CA5 7HH, United Kingdom 

Tel: +44 (0)16974 78277 • Fax: +44 (0)16974 78530 

E-mail: info@steadmans.co.uk • Website: www.steadmans.co.uk 


Scope: 

Manufacture of AS35 sandwich roof and wall panels. Manufacture of cold rolled section, including purlins, facias and fittings associated 

with wall and roof panels. 

A.C. Plastic Industries Limited 

Unit J Loddon Business Centre, Roentgen Road, Basingstoke, Hants RG24 8NG, United Kingdom 

Tel: +44 (0)1256 329334 • Fax: +44 (0)1256 817862 

E-mail: sales@ac-plastics.com • Website: www.ac-plastics.com 


Scope: 

Manufacture and installation of hot press moulded GRP sectional water storage tanks. 

A.M. Fire Systems Limited 

Red Brook Mill, Bury Road, Rochdale OL11 4EE, United Kingdom 

Tel: +44 (0)1706 639439 • Fax: +44 (0)1706 347733 

E-mail: andyedmunds@amfiresystems.co.uk 


Scope: 

Design and installation of fire sprinkler, water spray and foam systems. 

Abbot Fire Group Limited 

Abbots Barn, Radclive Road, Gawcott, Buckingham MK18 4AA, United Kingdom 

Tel: +44 (0)870 844 1666 • Fax: +44 (0)870 844 1777 

E-mail: admin@abbotfiregroup.co.uk 


Scope: 

Installation and servicing of portable fire extinguishers. Installation and servicing of kitchen suppression systems. 

540 20 Nov 2011



AccentHansen 

Greengate Industrial Park, Greengate, Middleton, Manchester M24 1SW, United Kingdom 

Tel: +44 (0)161 284 4100 • Fax: +44 (0)161 655 3119 

E-mail: info@accenthansen.co.uk • Website: www.servicehansen.com 


Scope: 

Design, manufacture and installation of industrial doors, security doors and fire doors. 

Actionair 

Ruskin Air Management, Joseph Wilson Industrial Estate, South Street, Whitstable, Kent CT5 3DU, United 

Kingdom 

Tel: +44 (0)1227 276100 • Fax: +44 (0)1227 264262 



Scope: 

The design, manufacture and supply of fire protection and air distribution products including: Electrically or pneumatically operated fire 

smoke dampers; Thermal release or electro magnetic release curtain fire dampers; Manually, electrically or pneumatically operated 

volume control and shut off dampers; Fan coil units; Control systems and ancillary products. 

AD Sprinkler Protection Limited 

2/8 Heaton Mill, Grey Street, Denton, Manchester M34 3RG, United Kingdom 

Tel: +44 (0)161 336 0001 • Fax: +44 (0)161 336 6608 

E-mail: mail@adsprinklers.co.uk • Website: www.adsprinklers.co.uk 


Scope: 

Design, installation and service of fire sprinkler systems. 

Advanced Electronics Limited 

34 Moorland Way, Nelson Park, Cramlington, Northumberland NE23 1WE, United Kingdom 

Tel: +44 (0) 1226 737 465 • Fax: +44 (0) 1226 737 469 

E-mail: ithompson@advel.co.uk • Website: www.Advel.co.uk 

Also at: 

2 Claycliffe Office Park, Whaley Road, Barnsley, South Yorkshire S75 1HT, United Kingdom 


Scope: 

Design and manufacture of fire detection panels, emergency lighting and safety control equipment. 

AEI Cables Limited 

Birtley, Chester-le-Street, Co. Durham DH3 2RA, United Kingdom 

Tel: +44 (0)191 410 3111 • Fax: +44 (0)191 410 8312 

E-mail: sales@aeicables.co.uk • Website: www.aeicables.co.uk 


Scope: 

20 Nov 2011 541



Design and manufacture of electric cables for use in fire alarm installations. 

Alliance Valves and Piping Supplies Limited 'AVPS' 

Unit 2, Royd Business Park, Dyehouse Lane, Brighouse, West Yorkshire HD6 1LL, United Kingdom 

Tel: +44 (0)1484 401880 • Fax: +44 (0)1484 401881 

E-mail: sales@alliancevalves.co.uk • Website: www.alliancevalves.co.uk 


Scope: 

Supply of process and instrumentation valves fittings as associated for the oil, petrochemical and associated sectors. 

Alpine Fire Engineers Limited 

Sovereign House, Barehill Street, Littleborough, Lancashire OL15 9BL, United Kingdom 

Tel: +44 (0)1706 838200 • Fax: +44 (0)1706 838020 

E-mail: d.smith@alpinefire.co.uk • Website: www.alpinefire.co.uk 


Scope: 

Design, service and installation of fire sprinkler systems. 



Tel: +44 (0)800 977 8975 • Fax: +44 (0)1691 671 482 



Scope: 

Design, manufacture and fabrication of security shutters and garage doors and assembly and supply of photovoltaic systems. 

AMPAC Europe Limited 

Unit 18 Networkcentre, Yorkshire Way, Westmoor Park, Doncaster DN3 3GW, United Kingdom 

Tel: +44 (0)1302 833522 • Fax: +44 (0)1302 835021 

E-mail: info@ampac.net • Website: www.ampac.net 


Scope: 

The marketing, assembly and distribution of fire detection and emergency warning products and associated training. 

Ampac Security Products Limited 

Saxon Way, Melbourn, Royston, Hertfordshire SG8 6DN, United Kingdom 

Tel: +44 (0)1763 261900 • Fax: +44 (0)1763 261234 

Website: www.ampaconline.com 


Scope: 

The manufacture of tamper evident polythene security bags and envelopes. 

542 20 Nov 2011



Andreu Barbera S.L. 

Poligono Fuente Del Jarro, C/Ciudad De Sevilla, 20, 46988 Paterna, Valencia, Spain 

Tel: +34 96134 3100 • Fax: +34 961 34 0859 

E-mail: andreu@andreu.es • Website: www.andreu.es 

Quality System Cert. No. 922 Assessed to Factory Production Control to PN 111 

Scope: 

Design and production of metallic door sets and accessories. 

Ansul Incorporated 

One Stanton Street, Marinette, Wisconsin 54143-2542, United States 

Tel: +1 715 735 7411 • Fax: +1 715 732 3477 

Website: www.ansul.com 


Scope: 

Design and manufacture of restaurant fire protection systems and fire suppression wet agents. 

Anvil International Inc. 

1411 Lancaster Avenue, Columbia, Pennsylvania 17512, United States 

Tel: +1 717 684 4400 • Fax: +1 717 684 2131 

Website: www.anvilintl.com 


Scope: 

Manufacture of pipe couplings fittings and valves. Malleable and gray iron threaded fittings and pipe hangers. 

Anvil International Inc. 

2870 Old Jackson Road, Henderson, Tennessee 38340, United States 

Tel: +1 731 989 3551 • Fax: +1 731 989 4144 


Scope: 

Manufacture of pipe hangers. Metal stamping and fabrication. 

Apollo (Beijing) Fire Products Co Ltd 

No. 5, Industrial District North-West Jia, Jiugong Town Daxing District, Beijing 100076, China 

Tel: +86 10 8361 7122 • Fax: +86 10 8361 7017 

E-mail: lhxf@uip.163.com 


Scope: 

Design, manufacture, service and repair of fire detectors and alarm system components. 

20 Nov 2011 543



Apollo Fire Detectors Limited 

36 Brookside Road, Havant, Hampshire PO9 1JR, United Kingdom 

Tel: +44 (0)2392 492412 • Fax: +44 (0)2392 492754 

E-mail: enquiries@apollo-fire.co.uk 


Scope: 

Design, manufacture, service and repair of fire detectors for commercial/industrial applications. 

APW Fire Protection Limited 

Unit A, Marlfield Factory, Front Road, Drumbo, Lisburn BT27 5JY, United Kingdom 

Tel: +44 (0)28 90827046 • Fax: +44 (0)28 90827049 

E-mail: will@apwfp.com 


Scope: 

Design, installation and servicing of fire sprinkler systems. 

ArcelorMittal Construction Belgium 

Zone Industrielle de Martinrou, 21b rue de Berlaimont, Fleurus, Belgium 

Tel: +32 (0) 718 70540 • Fax: +32 (0) 718 70541 

Website: www.arcelormittal.com 


Scope: 

Sales and manufacture of mineral wool insulation panels for construction. 

ArcelorMittal Construction Belgium NV 

Lammerdries 8, Industrieterrein Geel West Z4, B-2440 Geel, Belgium 

Tel: +32 14563943 • Fax: +32 14563952 

E-mail: eric.mees@arcelormittal.com • Website: www.arclad.be 


Scope: 

Production of sandwich panels for industrial and utility buildings. 

Argus Fire Protection Company Limited 

Hendglade House, 46 New Road, Stourbridge, West Midlands DY8 1PA, United Kingdom 

Tel: +44 (0)1384 376256 • Fax: +44 (0)1384 393955 

E-mail: info@argusfire.co.uk • Website: www.argusfire.co.uk 


Scope: 

Design and installation of fire sprinkler, water spray and foam systems. Installation, commissioning and servicing of fire detection and 

alarm systems. 

544 20 Nov 2011



Argus-Spectrum Co 

65 Serdobolskaya St, St. Petersburg 197342, Russian Federation 

Tel: +7 812 7037500 • Fax: +7 812 7037501 

E-mail: mail@argus-spectr.ru • Website: www.argus-spectr.ru 


Scope: 

Design and manufacture of fire and security alarm system components 

Armstrong Priestley Limited 

Seventy Seven, Holbeck Lane, Leeds LS11 9UL, United Kingdom 

Tel: +44 (0)113 3944040 • Fax: +44 (0)113 3944041 

E-mail: info@armstrongpriestley.co.uk • Website: www.armstrongpriestley.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler, water spray and foam systems, hydrants and hose reels. Fabrication of pipework for fire 

sprinkler systems. 



Tel: +44 (0)1204 545801 • Fax: +44 (0)1204 545800 



Scope: 

Manufacture, installation, servicing and repair of industrial doors, industrial rolling shutters, fire doors and fire rolling shutters. 

Ashvale Fire Services Limited 

Ashvale House, Fitzroy Street, Ashton-under-Lyne, Lancashire OL7 0JG, United Kingdom 

Tel: +44 (0)161 343 1090 • Fax: +44 (0)161 343 3732 

E-mail: sales@ashvalefire.co.uk • Website: www.ashvalefireservices.com 


Scope: 


ASLR Fabrication Services Limited 

Opal Way, Stone Business Park, Stone, Staffordshire ST15 0SS, United Kingdom 

Tel: +44 (0)1785 286060 • Fax: +44 (0)1785 818728 

E-mail: sales@aslr.co.uk • Website: www.aslr.co.uk 


Scope: 

Manufacture and supply of pre fabricated pipework for the fire protection, building services, water and process engineering industries. 

20 Nov 2011 545



ATOM KABLO SANAYI VE TICARET A.S. 

Ankara Karayolu 6. Km, Akkale Bedesi, Denizli 20155, Turkey 

Tel: +90 258 274 63 52 • Fax: +90 258 274 64 31 

E-mail: atom@atom.com.tr • Website: www.atom.com.tr 


Scope: 

The manufacture and suppy of electric cables and wires, including cables used for installations which require safety in the event of fire. 

Attenborough Doors Limited 

Merlin Way, Quarry Hill Industrial Estate, Ilkeston, Derbyshire DE7 4RA, United Kingdom 

Tel: +44 (0)115 9300815 • Fax: +44 (0)115 9448930 

E-mail: information@attenboroughdoor.co.uk • Website: www.attenboroughdoor.co.uk 


Scope: 

Manufacture and installation of industrial rolling shutters and fire rolling shutters. 

Automatic Fire Control Limited 

Unit 7 Kingsdown Orchard, Hyde Road, Swindon SN2 7RR, United Kingdom 

Tel: +44 (0)1793 821588 • Fax: +44 (0)1793 821587 

E-mail: info@automaticfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. 

Bahra Cables Company 

CPC Industrial Park, Bahra, Jeddah 21432, Kingdom of Saudi Arabia 

Tel: +966 25911115, (Toll Free) 8001248111 • Fax: +966 25915683 

E-mail: fsb@bahra-cables.com • Website: www.bahra-cables.com 


Scope: 

Manufacture of single core fire resistant cables tested to BS 6387:1994 Cat CWZ. Conductor cross sectional area 2.5mm 2 - 25mm 2 . 

Bailey & Mackey Limited 

Baltimore Road, Birmingham B42 1DE, United Kingdom 

Tel: +44 (0)121 357 5351 • Fax: +44 (0)121 357 8319 

E-mail: enquiries@baileymackey.com • Website: www.baileymackey.com 


Scope: 

Design and manufacture of calibrated pressure gauges, pressure switches, pressure transducers and vapour pressure temperature 

gauges. Repair and re-calibration of pressure gauges, pressure switches, pressure transducers and vapour pressure temperature 

gauges, in the range of absolute vacuum up to 1000 bar gauge, and temperature range of 20 degrees celsius up to 200 degrees celsius. 

546 20 Nov 2011



Balmoral Sectional Tanks Limited 

(A Division of Balmoral Group Holdings Limited), Balmoral Park, Loirston, Aberdeen AB12 3GY, United 

Kingdom 

Tel: +44 (0)1224 859000 • Fax: +44 (0)1224 859123 

E-mail: tanks@balmoral.co.uk • Website: www.balmoraltanks.com 


Scope: 

Design, manufacture and installation of hot press moulded GRP sectional water storage tanks. 

Bangkok Cable Co Limited 

187/1 Rajdamri Road, Lumpinee, Pathumwan, Bangkok 10330, Thailand 

Tel: +662 254 4550 • Fax: +662 254 3859 

E-mail: sales@bangkokcable.com 

Manufacture at: 

93 Moo. 11, Suksawad Rd, Naiklongbangplakod, Prasamutchedee, Samutprakarn 10290, Thailand 


Scope: 

Design and manufacture of cables for use in installations that require safety in the event of fire. 

BBC Fire Protection Limited 

St Florian House, Ayton Road, Wymondham, Norfolk NR18 0QH, United Kingdom 

Tel: +44 (0)1953 857700 • Fax: +44 (0)1953 857750 

E-mail: sales@bbcfire.co.uk • Website: www.bbcfire.co.uk 


Scope: 

Installation, commissioning and servicing of fire detection and alarm systems. 

Beijing Siemens Cerberus Electronics Limited 

No. 1, Feng Zhi Dong Lu, Xi Bei Wang, Haidian District, Beijing 100094, China 

Tel: +86 010 629 62255 • Fax: +86 010 629 87387 

E-mail: hongyan.lv@siemens.com 


Scope: 

Design and manufacture of fire detection and alarm equipment, intruder detection and alarm equipment. Design and manufacture of 

electronic and mechanical control products and systems for HVAC applications, room-controls and building automation. 

Besseges Limited 

Riverside, Dukinfield, Cheshire SK16 4HE, United Kingdom 

Tel: +44 (0)161 308 3252 • Fax: +44 (0)161 339 5003 

E-mail: sales@besseges.co.uk • Website: www.besseges.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems. Fabrication of pipework. 

20 Nov 2011 547



Biamp Systems Corporation 

9300 S.W. Gemini Drive, Beaverton, Oregon 97008, United States 

Tel: +1 503 718 9212 • Fax: +1 503 626 0281 

Website: www.biamp.com 


Scope: 

Design and manufacturer of audio equipment including voice alarm control and indicating equipment. 

Blue Shield Fire Protection Limited 

Blue Shield House, Queen Street, Tring, Hertfordshire HP23 6BQ, United Kingdom 

Tel: +44 (0)1442 828000 • Fax: +44 (0)1442 828001 

E-mail: sales@blueshieldfire.co.uk • Website: www.blueshieldfire.co.uk 


Scope: 

Design, installation, service and repair of fire sprinkler systems. 

Bolton Gate Co. Limited 

Waterloo Street, Bolton, Lancashire BL1 2SP, United Kingdom 

Tel: +44 (0)1204 871000 • Fax: +44 (0)1204 871049 

E-mail: kb@boltongate.co.uk • Website: www.boltongate.co.uk 

Quality System Cert. No. 026-2 Assessed to ISO 9001:2008 

Scope: 

Manufacture and installation of industrial doors, industrial rolling shutters, fire doors and fire rolling shutters. 

Booth Industries Limited 

P.O. Box 50, Nelson Street, Bolton, Lancashire BL3 2AP, United Kingdom 

Tel: +44 (0)1204 366333 • Fax: +44 (0)1204 380888 

E-mail: marketing@booth-industries.co.uk • Website: www.booth-industries.co.uk 

Also at: 

Unit D, Lecturers Close, Bridgeman Street, Bolton BL3 6DG, United Kingdom 


Scope: 

Design and manufacture of blast walls, blast panels and blast doors. Manufacture of fire walls, fire panels, fire doors, security doors and 

industrial doors. 

BPI Visqueen - Greenock 

96 Port Glasgow Road, Greenock, Scotland PA15 2UL, United Kingdom 

Tel: +44 (0)1475 501100 • Fax: +44 (0)1475 743256 

Website: www.bpipoly.com 


Scope: 

Manufacture of flame retardant plastic protection material. 

548 20 Nov 2011





Tel: +44 (0)1724 271999 • Fax: +44 (0)1724 271888 



Scope: 

Design, manufacture and installation of physical security products. 

Braithwaite Engineers Limited 

Neptune Works, Uskway, Newport, South Wales NP20 2UY, United Kingdom 

Tel: +44 (0)1633 262141 • Fax: +44 (0)1633 250631 

E-mail: tanks@braithwaite.co.uk • Website: www.braithwaite.co.uk 


Scope: 

The design, supply and installation of sectional pressed steel tanks and glass reinforced plastic (GRP) cold water storage tanks, including 

the manufacture of custom GRP panels and components. 

Brammall Inc. 

Doing business as Tyden Brooks Security Products, 409 Hoosier Drive, Angola, Indiana 46703, United States 

Tel: +1 260 665 3176 • Fax: +1 260 665 8309 

E-mail: insidesales@tydenbrooks.com • Website: www.tydenbrooks.com 


Scope: 

Design and manufacture of cargo security seals. 

Britannia Kitchen Ventilation Limited 

10 Highdown Road, Leamington Spa, Warwickshire CV31 1XT, United Kingdom 

Tel: +44 (0)1926 463540 • Fax: +44 (0)1926 463941 

E-mail: sales@kitchen-ventilation.co.uk • Website: www.kitchen-ventilation.co.uk 


Scope: 

Design, manufacture and installation of commercial and institutional kitchen ventilation canopies and associated equipment. 

BSB Engineering Services Limited 

Unit E, Tribune Drive, Trinity Trading Estate, Sittingbourne, Kent ME10 2PD, United Kingdom 

Tel: +44 (0)1795 422609 • Fax: +44 (0)1795 429543 

E-mail: sales@bsb-dampers.co.uk • Website: www.bsb-dampers.co.uk 


Scope: 

Design, manufacture and supply of fire dampers (fire curtains), fire smoke dampers, smoke control dampers and volume control dampers. 

20 Nov 2011 549



Burton Safes Limited 

Unit 12, Brockholes Business Park, Rockmill Road, Brockholes, Holmfirth HD9 7BN, United Kingdom 

Tel: +44 (0)1484 663388 • Fax: +44 (0)1484 666338 

Website: www.burtonsafes.co.uk 


Scope: 

Distribution, supply and commissioning of safes, safe locks, strong rooms and security cabinets. 

Bush (Fire Engineering) Limited 

Unit 28 The Metro Centre, Kangley Bridge Road, Sydenham, London SE26 5BW, United Kingdom 

Tel: +44 (0)845 241 9860 • Fax: +44 (0)845 241 9861 

E-mail: sales@bushengineering.com 


Scope: 

Design, installation and servicing of fire sprinkler systems. Installation and servicing of dry risers. 

CA Group Limited 

Evenwood Industrial Estate, Copeland Road, Evenwood, Co. Durham DL14 9SF, United Kingdom 

Tel: +44 (0)1388 834242 • Fax: +44(0)1388 834881 

E-mail: help@cagroup.ltd.uk • Website: www.cagroup.ltd.uk 


Scope: 

Design, manufacture and supply of built-up roof and wall systems. 

Cavicel SpA 

Via Caduti del Lavoro, 18/A, 20096 Pioltello, Milan, Italy 

Tel: +39 02 9216 0521 • Fax: +39 02 9216 0753 

E-mail: cavicel@cavicel.com • Website: www.cavicel.com 


Scope: 

Design and manufacture of electric cables for installations that require safety in the event of fire. 

Ceodeux - Firetec 

24 Route de Diekirch - B.P.19, L-7505 Lintgen, Luxembourg 

Tel: +352 32 78 32-1 • Fax: +352 32 78 32-326 

E-mail: info@firetec.rotarex.com • Website: www.rotarex.com 


Scope: 

Development, assembly, test and sale of BO480 differential pressure valves for fire suppression systems. 

550 20 Nov 2011



Chaoyi Industry Development 

3/F No. 4 Factory Building, Lang Kou Industrial Estate, Lang Kou Road, Lang Hau, Bao An District, 

Shenzhen, China 

Tel: +755 338 76556 • Fax: +755 338 76538 

E-mail: szchaoyi@163.com 


Scope: 

Manufacture of fire alarm bells. 

Charter Sepcialist Security Limited 

Innovation House, Arkwright Road, Reading, Berkshire RG2 0LU, United Kingdom 

Tel: +44 (0) 845 0508705 • Fax: +44 (0) 845 0508707 

E-mail: sales@chatergroupuk.com • Website: www.chartergroupuk.com 


Scope: 

Design, manufacture, fabrication, installation and repair of roller shutter systems. 

Chemring Energetics Limited 

Ardeer Site, Stevenston, Ayrshire, Scotland KA20 3LN, United Kingdom 

Tel: +44 (0)1294 487007 • Fax: +44 (0)1294 487230 

E-mail: campbell.howie@chemringenergetics.co.uk • Website: www.chemringenergetics.co.uk 


Scope: 

Manufacture of Metron actuators for installation in fire fighting systems. 

Chubb Fire & Security Limited 

400 Dallow Road, Luton, Beds LU1 1UR, United Kingdom 

Tel: +44 (0)1582 413694 • Fax: +44 (0)1582 456353 

E-mail: quality.fireuk@chubb.co.uk • Website: www.chubb.co.uk 


Scope: 


Chubb Fire & Security Limited 

5 Canal Place, Armley Road, Leeds LS12 2DU, United Kingdom 

Tel: +44 (0)113 235 5131 • Fax: +44 (0)113 235 5132 

E-mail: fire.leeds@chubb.co.uk • Website: www.chubb.co.uk 


Scope: 


20 Nov 2011 551



Circum Limited 

Roundhouse Farm, Roestock Lane, Colney Heath, Hertfordshire AL4 0PP, United Kingdom 

Tel: +44 (0)1727 821228 • Fax: +44 (0)1727 822428 

E-mail: sfulcher@circum.ltd.uk • Website: www.circum.ltd.uk 


Scope: 

Design, installation, service and maintenance of fire sprinkler systems, gas suppression systems and the sale of associated fire products. 



Tel: +44 (0)1228 522321 • Fax: +44 (0)1228 401854 



Scope: 

Manufacture and installation of industrial doors, industrial rolling shutters, fire doors and fire rolling shutters. 



Tel: +44 (0)1270 764751 • Fax: +44 (0)1270 757503 



Scope: 

Design, manufacture and supply of perimeter, security and sports fencing systems. 


11 Landau Way, Darent Industrial Park, Erith, Kent DA8 2LF, United Kingdom 

Tel: +44 (0)1322 332211 • Fax: +44 (0)1322 339582 

E-mail: info@clearwayservices.co.uk • Website: www.clearwayservices.co.uk 


Scope: 

Provision and installation of security doorsets for property protection. 

Clymac Limited 

Cloudway Court, Belton Road, Loughborough LE11 1LW, United Kingdom 

Tel: +44 (0)1509 232651 • Fax: +44 (0)1509 232665 

E-mail: sales@clymac.co.uk • Website: www.clymac.co.uk 


Scope: 

Design, supply, installation, commissioning and servicing of fire detection and alarm systems. 

552 20 Nov 2011



Compco Fire Systems Limited 

Cleeve House, Malvern Road, Lower Wick, Worcester WR2 4YX, United Kingdom 

Tel: +44 (0)1905 741600 • Fax: +44 (0)1905 741620 

E-mail: enquiries@compcofire.co.uk 

Also at: 

High Banks House, Lawn Lane, Hemel Hempstead, Hertfordshire HP3 9HR, United Kingdom 

Tel: +44 (0)1442 242821 

and 

23 Fairfield Place, College Milton, East Kilbride G74 5LP, United Kingdom 

Tel: +44 (0)1355 570033 • Fax: +44 (0)1355 570044 

E-mail: david.m@compcofire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler and foam systems, and hose reels. 

Computionics Limited (Trading as C-Tec) 

Stephens Way, Goose Green, Wigan, Lancashire WN3 6PH, United Kingdom 

Tel: +44 (0)1942 322744/42444 • Fax: +44 (0)1942 829867 

E-mail: sales@C-tec.co.uk • Website: www.c-tec.co.uk 

Also at: 

Dark Lane, Mawdesley L40 2QU, United Kingdom 


Scope: 

Design and manufacture of fire and security control and indicating equipment, associated alarm system components, and call equipment. 

Control Equipment Limited 

Hillcrest Business Park, Dudley, West Midlands DY2 9AP, United Kingdom 

Tel: +44 (0)1384 458651 • Fax: +44 (0)1384 458972 

E-mail: celsales@controlequipment.co.uk • Website: www.controlequipment.com 


Scope: 

Design and manufacture of detection and electronic control equipment for fire protection and other PCB assembly. 

Cooper Fulleon Limited 

Llantarnam Park, Cwmbran, South Wales NP44 3AW, United Kingdom 

Tel: +44 (0)1633 628500 • Fax: +44 (0)1633 866346 

E-mail: sales@fulleon.co.uk • Website: www.cooperfulleon.com 


Scope: 

Design and manufacture of alarm sounders, beacons and manually activated signalling devices. 

20 Nov 2011 553



Cooper Lighting and Safety Limited 

Wheatley Hall Road, Doncaster, South Yorkshire DN2 4NB, United Kingdom 

Tel: +44 (0)1302 303303 • Fax: +44 (0)1302 367155 

E-mail: sales@cooper-ls.com • Website: www.cooper-Is.com 


Scope: 

Design and manufacture of fire detection and alarm panels. 

Core Industrial Plastics Limited 

Unit 12, A1 Ferrybridge Business Park, Fishergate, Knottingley, West Yorkshire WF11 8NA, United Kingdom 

Tel: +44 (0)1977 676072 • Fax: +44 (0)1977 676069 

E-mail: sales@coreplastics.co.uk 


Scope: 

Procurement and supply of printed FR board. 

Corus Panels and Profiles 

Shotton Works, Flintshire CH5 2NH, United Kingdom 

Tel: +44 (0)1684 856600 • Fax: +44 (0)1684 856601 

E-mail: sales@coruspanelsandprofiles.co.uk • Website: www.coruspanelsandprofiles.com 


Scope: 

Design, manufacture and supply of metal-faced profiles, roof and wall cladding, composite flooring, composite panels, façade systems, 

rain screen systems, structural tray systems including ancillary items and flashings in accordance with client’s specified requirements. 

Cranford Controls Limited 

Unit 2, Waterbrook Estate, Waterbrook Road, Alton, Hampshire GU34 2UD, United Kingdom 

Tel: +44 (0)1420 592444 • Fax: +44 (0)1420 592445 

E-mail: sales@cranfordcontrols.com • Website: www.cranfordcontrols.com 


Scope: 

Design, supply and manufacture of fire detection and alarm system accessories. 


7 Churchill Way, 35A Business Park, Chapeltown, Sheffield, South Yorkshire S35 2PY, United Kingdom 

Tel: +44 (0)870 609 4474 • Fax: +44 (0)114 257 4397 

E-mail: sales.uk@crawfordsolutions.com • Website: www.crawfordsolutions.uk.com 


Scope: 

Supply, installation, maintenance and repair of industrial doors and loading bay equipment. 

Service Centres: 

Central & Southern UK: 

7 Churchill Way, 35A Business Park, Chapeltown, Sheffield, South Yorkshire S35 2PY 

Tel: +44 (0)870 609 4474 • Fax: +44 (0)114 257 4397 

554 20 Nov 2011



Email: service.uk@crawfordsolutions.com • Website: www.crawfordsolutions.uk.com 

Northern UK: 

First Floor, Cedar House, Quarry Court, Livingston, West Lothian EH54 6AX 

Tel: +44 (0)1506 417237 • Fax: +44 (0)1506 412726 

Email: service.uk@crawfordsolutions.com • Website: www.crawfordsolutions.uk.com 

Out of office hours: Tel.: +44 (0)1244 355235 

New Product Sales & Installation: 

Contact Details: 

7 Churchill Way, 35A Business Park, Chapeltown, Sheffield, South Yorkshire S35 2PY 

Tel: +44 (0)114 257 4330 • Fax: +44 (0)114 257 4399 

Certificate No. 001 Assessed to ISO 9001:2008 

Scope: 

Supply and installation of industrial doors and loading bay equipment. 

CTM Fire and Security Limited (Leyland & London Offices) 

Unit 2, Osprey Place, Moss Side Industrial Estate, Leyland PR26 7EW, United Kingdom 

Tel: +44 (0)800 5872753 • Fax: +44 (0)1772 641227 

E-mail: ctmfire@btconnect.com • Website: www.firealarmuk.com 

Including satellite office at: 

BBC Television Centre, Arch 118, Dodds Yard, Wood Lane, London W12 7RJ, United Kingdom 


Scope: 

Design, supply, installation, commissioning and servicing of fire detection and alarm systems. Installation, service of portable fire 

extinguishers. 

Culimeta-Saveguard Limited 

Tame Valley Mill, Wainwright Street, Dukinfield, Cheshire SK16 5NB, United Kingdom 

Tel: +44 (0)161 344 2484 • Fax: +44 (0)161 344 2486 

E-mail: sales@saveguard.com 


Scope: 

Design, manufacture and supply of cavity fore barriers and related fire protection products, protective textiles, thermal and accoustic 

insulation. 

D.I.S. Sprinklers 

183 Westgate Street, Gloucester GL1 2RN, United Kingdom 

Tel: +44 (0)1452 304927 • Fax: +44 (0)1452 306692 

E-mail: sprinklers@dis-ltd.co.uk • Website: www.dis-ltd.co.uk 


Scope: 


20 Nov 2011 555



Daemon Fire and Security Limited 

Daemon House, 41-42 Albert Road, Tamworth, Staffs B79 7JS, United Kingdom 

Tel: +44 (0)1827 69266 • Fax: +44 (0)1827 53584 

E-mail: sales@daemonfire.co.uk 


Scope: 


Dalen Limited 

Valepits Road, Garretts Green Industrial Estate, Birmingham B33 0TD, United Kingdom 

Tel: +44 (0)121 783 3838 • Fax: +44 (0)121 784 6348 

E-mail: sales@top-tec.co.uk • Website: www.top-tec.co.uk 


Scope: 

Manufacture of physical security devices, computer and TV stands, materials handling and storage equipment, access platforms and 

general metal fabrication and powder coating services. 

Datatag ID Limited 

3000 Hillswood Drive, Hillswood Business Park, Chertsey, Surrey KT16 0RS, United Kingdom 

Tel: +44 (0)1932 895304 • Fax: +44 (0)1932 796797 

E-mail: info@datatag.co.uk • Website: www.datatag.co.uk 

24/7 Telephone Number: 0845 0700 440 


Scope: 

Design and distribution of asset identification systems and provision of secure database registration services. 

Dätwyler Cables 

Unit of Dätwyler Switzerland Inc, Gotthardstrasse 31, CH-6460 Altdorf, Switzerland 

Tel: +41 41 875 1122 • Fax: +41 41 875 1860 

E-mail: info.ch@daetwyler-cables.com • Website: www.daetwyler-cables.com 


Scope: 

Design and manufacture of electric cables for use in fire alarm installations. 

Day-Impex Limited 

Station Works, Earls Colne, Colchester, Essex CO6 2ER, United Kingdom 

Tel: +44 (0)1787 223232 • Fax: +44 (0)1787 224171 

E-mail: grahaml@day-impex.co.uk • Website: www.day-impex.co.uk 


Scope: 

Manufacture of glass bulbs for fire sprinklers. 

556 20 Nov 2011



Debro Engineering and Presswork trading as Unistrut Ltd 

Unit 2 Delta Point Trading Estate, Greets Green Road, West Bromwich, West Midlands B70 9PL, United 

Kingdom 

Tel: +44 (0)121 580 6350 • Fax: +44 (0)121 580 6364 

Website: www.unistrut.co.uk 


Scope: 

Manufacture of brackets and pipe support equipment. 

Defensor Group Limited 

Defensor House, 15 Kingsley Street, Leicester LE2 6DY, United Kingdom 

Tel: +44 (0)116 244 8689 • Fax: +44 (0)116 244 8884 

E-mail: j.kyte@defensorfds.co.uk 


Scope: 

Design, installation, commissioning, service and maintenance of fire detection and alarm systems. 

Delta Extinctors S. A. 

Birmingham Street 102, Brussels 1070, Belgium 

Tel: +32 (0) 2 528 08 70 • Fax: +32 (0) 2 521 07 31 

E-mail: info@delta.be • Website: www.delta.be 


Scope: 

Manufacture of portable 1kg, 2kg & 3kg (BC & ABC powder) extinguishers in accordance with EN 3. 



Tel: +44 (0)1685 350114 • Fax: +44 (0)1685 723276 



Scope: 

Design and manufacture of steel hinged door sets. 

Dewey Waters Limited 

Heritage Works, Winterstoke Road, Weston-Super-Mare, Somerset BS24 9AN, United Kingdom 

Tel: +44 (0)1934 421477 • Fax: +44 (0)1934 421488 

E-mail: sales@deweywaters.co.uk • Website: www.deweywaters.co.uk 


Scope: 

Manufacture and installation of GRP sectional and one-piece tanks, and industrial and commercial mouldings. 

20 Nov 2011 557



Digital Lighting (Dongguan) Co Ltd 

Xinmin Road, Xinmin District, Chang'an Town, Dongguan City, Guandong Province, China 

Tel: +86 769 5332372 • Fax: +86 769 5538520 

E-mail: info@dl-sv.com • Website: www.dl-sv.com 


Scope: 

The design and manufacture of fire detection and alarm system components. 

Doncaster Cables 

Millfields Industrial Estate, Arksey Lane, Bentley, Doncaster, South Yorkshire DN5 0SJ, United Kingdom 

Tel: +44 (0)1302 821700 • Fax: +44 (0)1302 821701 

E-mail: sales@doncastercables.com • Website: www.doncastercables.com 


Scope: 

Manufacture of electric cables for use in installations that require safety in the event of fire. 

Dong-A Flexible Metal Tubes Co. Ltd. 

4F Kowon Bldg. 20-19, Yangjae-Dong, Seocho-Gu, Seoul 137-888, Korea, Republic Of 

Tel: +82 (0)2 3476 2541 • Fax: +82 (0)2 3476 2540 

E-mail: daflex@daflex.co.kr 

Also at: 

#412-2 Chubook-Ri, Yangji-Myon, Yongin-Si, Gyeonggi-Do 449-822, Korea, Republic Of 


Scope: 

Design and manufacture of flexible hoses for sprinkler systems, flexible tubing for gas supplies and water supplies, uncoated or plastic 

coated. 

DoorTechnik 

Moor Lane, Thorpe-on-the-Hill, Lincoln LN6 9BW, United Kingdom 

Tel: +44 (0)1522 693522 • Fax: +44 (0)1522 508494 

Website: www.doortechnik.co.uk 


Scope: 

Design, manufacture, installation and repair of fabricated products including general fabrication and metal based parts of a non-structural 

nature. 

Draka UK Limited 

Alfreton Road, Derby DE21 4AE, United Kingdom 

Tel: +44 (0)1332 345431 • Fax: +44 (0)1332 331237 

E-mail: firetuf@drakauk.com • Website: www.drakauk.com 


Scope: 


558 20 Nov 2011



DS SMITH CORREX (Trading as a division of DS Smith Plastics Limited) 

Madleaze Industrial Estate, Bristol Road, Gloucester GL1 5SG, United Kingdom 

Tel: +44 (0)1452 316500 • Fax: +44 (0)1452 300436 

E-mail: sales@kayplast.com • Website: www.kaysersberg-plastics.com 


Scope: 

Design and development of plastics packaging and other products using thermoforming, injection moulding and structural foam, and 

conversion of structural sheet material. Manufacture of structural sheet and conversion into packaging and other products including flame 

retardant materials. 

Dubai Cable Company (Private) Limited, Trading as Ducab 

Old Abu Dhabi Road, Jebel Ali, Dubai, United Arab Emirates 

Tel: +9714 808 2500 • Fax: +9714 808 2622 

E-mail: ducab@ducab.com • Website: www.ducab.com, Sales office: PO Box 11529, Dubai, UAE 


Scope: 

Manufacture of electric cables for installations that require safety in the event of fire. 

Dubai Cable Company (Private) Limited, Trading as Ducab 

Ducab-M1, Plot No. - 2D12,3D2,4D2,5D2, Sector - M41, Industrial City of Abu Dhabi-1, Mussafah, Abu Dhabi, 

United Arab Emirates 

Tel: +9714 808 2500 • Fax: +9714 808 2622 

E-mail: ducab@ducab.com • Website: www.ducab.com 


Scope: 

Manufacture of electric cables for installations that require safety in the event of fire. 



Tel: +44 (0)1384 239991 • Fax: +44 (0)1384 455129 



Scope: 

Design and manufacture of free-standing safes. 

Duplus Architectural Systems Limited 

370 Melton Road, Leicester LE4 7SL, United Kingdom 

Tel: +44 (0)116 2610710 • Fax: +44(0)116 2610539 

E-mail: sales@duplus.co.uk • Website: www.duplus.co.uk 


Scope: 

Fabrication and installation of aluminium windows, doors and curtain walling. 

20 Nov 2011 559



EMCOR Facilities Services Limited, EMCOR Specialist Services 

Premier House, Tollgate, Eastleigh, Hampshire SO53 3YE, United Kingdom 

Tel: +44 (0)2380 648028 • Fax: +44 (0)2380 648191 

E-mail: david.parker@emcoruk.com 


Scope: 

Design, installation, commissioning, service and repair of fire detection and alarm systems. 

Emirates Fire Fighting Equipment Factory L.L.C. (FIREX) 

P.O.Box 22436, Industrial Area 13, Sharjah, United Arab Emirates 

Tel: +971 6 5340300 • Fax: +971 6 5340090 

E-mail: firex@emirates.net.ae • Website: www.firexuae.com 


Scope: 

Manufacture of fire cabinets, fire hose reels and wheeled unit fire extinguishers. Distribution of portable fire extinguishers and fire 

blankets. Design and installation of fire sprinkler systems, fire alarm systems and fire fighting systems. Distribution of landing valves and 

breech inlets. Design, manufacture and distribution of breech inlet cabinets. Manufacture of fire doors. 



Tel: +44 (0)1233 860080 • Fax: +44 (0)1233 860090 



Scope: 

Design, supply, distribution and installation of EnviroWrap flame retardant sheeting including the control of a sub contract manufacturing 

process. 

Essex Safety Glass Limited 

Units 1-3, Moss Road, Witham, Essex CM8 3UG, United Kingdom 

Tel: +44 (0)1376 520061 • Fax: +44 (0)1376 521176 

E-mail: sales@esguk.co.uk • Website: www.esguk.co.uk 


Scope: 

Manufacture of security rated and bullet resistant glass. 

560 20 Nov 2011



Eton Fire Limited 

Printers Gate, Limehouse Court, 3 - 11 Dod Street, London E14 7EQ, United Kingdom 

Tel: +44 (0)207 517 6300 • Fax: +44 (0)207 538 5231 

E-mail: fire@etonfire.com • Website: www.etonfire.com 

Also at: 

Aynsley House, Waterside Business Centre, Wolverhampton Road, Cannock WS11 1SN, United Kingdom 

Tel: +44 (0)1543 431 340 • Fax: +44 (0)1543 571 680 

E-mail: fire@etonfire.com • Website: www.etonfire.com 


Scope: 




Tel: + 44 (0)2920 776677 • Fax: + 44 (0)2920 369161 


Eurobond Doors Limited 

Tel: +44 (0)29 20 36 11 11 • Fax: +44 (0)29 20 36 22 22 

E-mail: sales@eurobonddoors.co.uk 

Eurobond Laminates Limited 

Tel: +44 (0)2920 77 66 77 • Fax: +44 (0)2920 36 91 61 

E-mail: sales@eurobond.co.uk 


Scope: 

Certificates 523 (Eurobond Doors Limited) and 545 (Eurobond Laminates Limited) have been merged and the scope is as follows:- 

Design, manufacture and supply of structural insulated panels, industrial doors, flashings and ancillaries. 



Tel: +44 (0)2920 790722 • Fax: +44 (0)2920 793149 



Scope: 

Manufacture of elite 1.25RW built-up roof and elite 55.30RW built-up wall rockfibre insulation plus elite 3.16GW built-up roof & elite 51.30 

built-up wall with glass wool insulation to LPS 1181 Part 1: Issue 1. 

20 Nov 2011 561



Everday Technology Co. Limited 

No 8, Lane 492, Ba-Der Street, Shulin 238, Taipei Hsien, Taiwan ROC 

Tel: +886 2 2668 9668 • Fax: +886 2 2668 9666 

E-mail: tech@everday.com • Website: www.everday.com 


Scope: 

Design and manufacture of smoke, heat, carbon monoxide, and gas detectors. 

Excel Industries Ltd 

Maerdy Industrial Estate (South), Rhymney, Gwent NP22 5PY, United Kingdom 

Tel: +44 (0)1685 845200 • Fax: +44 (0)1685 844106 

E-mail: info@excelfibre.com • Website: www.excelfibre.com 


Scope: 

Manufacture of Warmcel Panel Systems. 

Eyston Company Ltd 

27 Zhen Tian South Road, Wei Xing Industrial Zone, Yan Tian, Feng Gang, Dongguan, Guangdong, China 

Tel: +852 25573135 • Fax: +852 28970249 

E-mail: tracylo@eyston.com • Website: www.eyston.com 


Scope: 

Manufacture of smoke detectors. 

F.V.S. Limited 

Broom Street, Off Huddersfield Road, Newhey, Rochdale OL16 3RY, United Kingdom 

Tel: +44 (0)1706 848599 • Fax: +44 (0)1706 843474 

E-mail: fvs@fvslimited.co.uk • Website: www.fvslimited.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems. Fabrication of pipework for fire sprinkler systems. 



Tel: +44 (0)191 438 3222 • Fax: +44 (0)191 438 1686 



Scope: 

Design, manufacture and installation of specialist glazing systems. 

562 20 Nov 2011



FES Limited, FES Sprinklers 

Forth House, Pirnhall Business Park, Stirling FK7 8HW, United Kingdom 

Tel: +44 (0)1786 819600 • Fax: +44 (0)1786 811456 

E-mail: hq@fes.ltd.uk 


Scope: 

Design, installation, commissioning and servicing of sprinklers systems. 

FFE Fire & Security Limited 

122 The Minories, London EC3 1NT, United Kingdom 

Tel: +44 (0)845 60 999 06 • Fax: +44 (0)20 8665 4125 

E-mail: enquiries@ffe.co.uk • Website: www.ffe.co.uk 


Scope: 

Design, installation, commissioning, repair and servicing of fire detection and alarm systems. 

Fike Safety Technology Ltd 

Unit 31, Springvale Industrial Estate, Cwmbran, Gwent NP44 5BD, United Kingdom 

Tel: +44 (0)1633 865558 • Fax: +44 (0)1633 866656 

E-mail: fstinfo@fike.com • Website: www.fikesafetytechnology.co.uk 


Scope: 

Design and manufacture of fire alarm, detection and indicating equipment. 

Filling and Packing Materials Manufacturing Company (F.I.P.C.O.) 

P.O. Box 8762, Riyadh 11492, Kingdom of Saudi Arabia 

Tel: +966 1265 2299 • Fax: +966 1265 1275 


Scope: 

Manufacture of woven coated polypropylene sheets (in rolls) to flame retardant standard LPS 1207. 

Fire Alarm Solutions Limited 

Unit 2, Manor Way Business Centre, Fairview Industrial Park, Marsh Way, Rainham, Essex RM13 8UG, 


Tel: +44(0) 1708 521181 • Fax: +44(0) 1708 521182 

E-mail: enquiries@fas-ltd.com • Website: www.fas-ltd.com 


Scope: 

Sprinkler system design and project management. 

20 Nov 2011 563



Fire Defence (Northern) Limited 

Unit 9, B.B.I.C. Innovation Way, Wilthorpe, Barnsley, South Yorkshire S75 1JL, United Kingdom 

Tel: +44 (0)1226 289558 • Fax: +44 (0)1226 249625 

E-mail: fds@fire-defence.com • Website: www.fire-defence.com 


Scope: 


Fire Defence plc 

Crown Yealm House, Pathfields Business Park, South Molton EX36 3LH, United Kingdom 

Tel: +44 (0)1769 574070 • Fax: +44 (0)1769 574079 

E-mail: fds@fire-defence.com • Website: www.fire-defence.com 


Scope: 


Fire Logistics Limited 

Unit A4, Union Street, Shieldfield, Newcastle upon Tyne NE2 1AH, United Kingdom 

Tel: +44 (0)191 230 3647 • Fax: +44 (0)191 230 3650 

E-mail: enquiries@firelogistics.co.uk • Website: www.firelogistics.co.uk 


Scope: 

Design, supply, installation and servicing of fire sprinkler systems. 



Tel: +44 (0)1279 634 230 • Fax: +44 (0)1279 634 231 



Scope: 

Manufacture and installation of fire resistant ductwork systems and penetration seals. 

Fire Queen Limited 

23-37 Broadstone Road, Reddish, Stockport, Cheshire SK5 7AR, United Kingdom 

Tel: +44 (0)800 731 2748 • Fax: +44 (0)161 442 2664 

E-mail: enquiries@firequeen.co.uk • Website: www.firequeen.co.uk 


Scope: 

Supply, installation and servicing of portable fire extinguishers and fire hose reels. Supply and installation of fire safety notices. 

564 20 Nov 2011



Fire Security (Sprinkler Installations) Limited 

Homefield Road, Haverhill, Suffolk CB9 8QP, United Kingdom 

Tel: +44 (0)1440 705815 • Fax: +44 (0)1440 704352 

E-mail: info@firesecurity.co.uk • Website: www.firesecurity.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. Fabrication of pipework for fire sprinkler systems. 

Fireproof Fire Engineering Limited 

The Old Brewery, 40 Coldhurst Street, Oldham, Lancashire OL1 2BQ, United Kingdom 

Tel: +44 (0)161 620 0902 • Fax: +44 (0)161 620 0772 

E-mail: contactus@fireproofsprinklersystems.com • Website: www.fireproofsprinklersystems.com 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. 

Firespray International Limited 


Tel: +44 (0)1279 634 230 • Fax: +44 (0)1279 634 232 

E-mail: info@firespray.eu.com • Website: www.firespray.eu.com 


Scope: 

Manufacture and installation of fire resistant ductwork systems and penetration seals. 

Firetecnics Systems Limited 

142 Vauxhall Street, London SE11 5RH, United Kingdom 

Tel: +44 (0) 20 7587 0927 • Fax: +44 (0) 20 7582 3496 

E-mail: info@firetecnics.co.uk • Website: www.firetecnics.com 


Scope: 


First Fire Protection Limited 

Unit 3, Network 4, Lincoln Road, Cressex Business Park, High Wycombe, Buckinghamshire HP12 3RF, 


Tel: +44 (0)1494 522031/2 • Fax: +44 (0)1494 452752 

E-mail: enquiries@firstfireprotection.co.uk • Website: www.firstfireprotection.co.uk 


Scope: 


20 Nov 2011 565



Flameshield Products Limited (Incorporating Flameshield Limited) 

4 The Limes, Ingatestone, Essex CM4 0BE, United Kingdom 

Tel: +44 (0)1277 352202 • Fax: +44 (0)1277 355419 

E-mail: info@flameshield.org • Website: www.flameshield.org 


Scope: 

The operation of licensed manufacturing agreement(s) to manufacture - Flameshield Products Ltd, fire resistant ductwork systems and 

the supervision of the licensees FPC management system(s). 

The operation of a licensed installer service to - inspect and certify Flameshield Products Ltd, fire resistant ductwork system(s) 

installations. The supply and installation of Flameshield Products Ltd - fire resistant ductwork systems. 

Flexiform Business Furniture Limited-incorporating Asgard Secure Steel Storage 

1392 Leeds Road, Bradford, West Yorkshire BD3 7AE, United Kingdom 

Tel: +44 (0)1274 706206 • Fax: +44 (0)1274 660867 

E-mail: info@flexiform.co.uk • Website: www.flexiform.co.uk 


Scope: 

Design, manufacture and supply of business furniture and secure storage units. 

Fortress Doors N.I. Limited 

6 Trench Road, Hyde Park Industrial Estate, Newtownabbey, Belfast, Northern Ireland BT36 4TY, United 

Kingdom 

Tel: +44 (0)28 9034 2655 • Fax: +44 (0)28 9034 2651 

E-mail: grodgers@fortaxa.com • Website: www.fortaxa.com 


Scope: 

Design, manufacture and supply of fire and security doors and roller shutters. 

Franklin Hodge Industries Ltd. 

Jubilee Building, Faraday Road, Westfields Trading Estate, Hereford HR4 9NS, United Kingdom 

Tel: +44 (0)1432 269605 • Fax: +44 (0)1432 277454 

E-mail: sales@franklinhodge.com • Website: www.franklinhodge.com 


Scope: 

Design, manufacture and installation of water storage tanks, tank refurbishment and maintenance. 

Galglass Limited 

321 Hough Lane, Wombwell, Barnsley, South Yorkshire S73 0LR, United Kingdom 

Tel: +44 (0)1226 340370 • Fax: +44 (0)1226 344200 

E-mail: sales@galglass.co.uk • Website: www.galglass.com 


Scope: 

Design, manufacture and installation of cylindrical and rectangular water storage tanks. 

566 20 Nov 2011



Gaocheng General Foundry 

Yucai Road, Gaocheng City, Hebei Province, China 

Tel: +86 311 8816 6123 • Fax: +86 311 8819 3601 

E-mail: ixgzzc@163.net 


Scope: 

Manufacture and machining of grey and ductile iron castings. 

Globe Fire Sprinkler Corporation 

4077 Air Park Drive, Standish, Michigan 48658, United States 

Tel: +1 989 846 4583 • Fax: +1 989 846 9231 

Website: www.globesprinkler.com 


Scope: 

Design and manufacture of fire sprinklers, fire protection valves, and related products for fire sprinkler systems. 

Gloucester Composites Limited 

Fox House, Stonedale Road, Stonedale, Gloucestershire GL10 3SA, United Kingdom 

Tel: +44 (0)1453 791616 • Fax: +44 (0)1453 791516 

E-mail: sales@gloucestercomposites.com • Website: www.gloucestercomposites.com 


Scope: 

Manufacture of sectional water tanks and a range of hot pressed SMC moulded products. 

Godwin Pumps Limited 

Quenington, Cirencester, Gloucestershire GL7 5BX, United Kingdom 

Tel: +44 (0)1285 750271 • Fax: +44 (0)1285 750352 

E-mail: sales@godwinpumps.co.uk • Website: www.godwinpumps.co.uk 


Scope: 

Design, manufacture, commissioning and service of centrifugal pumping equipment, system packages and fire pumps. 

Goran Plastics 

Unit C, 5 Caxton Way, Watford Business Park, Watford, Herts WD18 8UA, United Kingdom 

Tel: +44 (0)1923 255700 • Fax: +44 (0)1923 255698 

E-mail: sales@goran.co.uk 


Scope: 

Manufacture of twinwall polypropylene sheeting. 

20 Nov 2011 567



Gordonson Fire Protection Limited 

Unit 8, Bombay Street, Bermondsey, London SE16 3UX, United Kingdom 

Tel: +44 (0)207 237 6707 • Fax: +44 (0)207 252 0152 

E-mail: gordonson@mailbox.co.uk 


Scope: 




Tel: +44 (0)131 440 7000 • Fax: +44 (0)131 440 7003 



Scope: 

Installation, servicing and repair of industrial doors, fire doors and fire rolling shutters. 

Grundfos Fire Systems 

Ferryboat Lane, Castletown, Sunderland SR5 3JL, United Kingdom 

Tel: +44 (0)191 549 5555 • Fax: +44 (0)191 516 0067 

Website: www.grundfos.co.uk 


Scope: 

Sales, manufacture and test of fire pumps and fire pump sets. 

Grundfos Europump Limited 

Oxford Court, Greenfold Way, Leigh, Lamcashire WN7 3XJ UK 

Scope: 

Installation, commissioning, service and repair of fire pumps and pump / sets. 

gte Brandschutz AG 

Hamburger Straße 2, D-14532 Stahnsdorf, Germany 

Tel: +49 3329 6359-0 • Fax: +49 3329 6359-25 

E-mail: gte@gte.ag • Website: www.gte.ag 


Scope: 

Design, manufacture, installation, service and repair of gte conveyor shutters. 

Gulf Security Technology Co. Ltd - A UTC Fire & Security Company 

No. 80 Changjiang East Road, Economic & Technological Development Zone, Qinhuangdao, Hebei Province 

066004, China 

Tel: +86 0335 8502528 • Fax: +86 0335 8508942 

E-mail: gst@gst.com.cn • Website: www.gst.com.cn 


Scope: 

Design and manufacture of fire detection and alarm systems and components. 

568 20 Nov 2011



Guthrie Douglas Limited 

12 Heathcote Way, Heathcote Industrial Estate, Warwick CV34 6TE, United Kingdom 

Tel: +44 (0)1926 452452 • Fax: +44 (0)1926 336417 

E-mail: info@guthriedouglas.com • Website: www.guthriedouglas.com 


Scope: 

Design, manufacture and repair of drive and control systems for building automation including access and security systems, fire, smoke 

and solar protection equipment. 

GW Sprinkler A/S 

Kastanievej 15, DK-5620 Glamsbjerg, Denmark 

Tel: +45 64 72 2055 • Fax: +45 64 72 2255 

E-mail: sales.dep@gwsprinkler.com 


Scope: 

Design and manufacture of fire sprinklers, fire protection valves and related products for fire sprinkler systems. 

H S Jackson & Son (Fencing) Limited, t/a Jacksons Fencing 

Stowting Common, Ashford, Kent TN25 6BN, United Kingdom 

Tel: +44 (0)1233 750393 • Fax: +44 (0)1233 750178 

E-mail: security@jacksons-fencing.co.uk • Website: www.jacksons-fencing.co.uk 


Scope: 

Design, manufacture, supply and installation of timber and steel, fencing, gate and security barriers to commercial, trade and domestic 

customers. 

The following location is included within the above scope of certification:- 

Ashford 

Stowting Common, Ashford, Kent TN25 6BN 

Tel: +44 (0)1233 750393 • Fax: +44 (0)1233 750178 

Scope: 

Manufacture, supply and installation of timber and steel, fencing, gate and security barriers to commercial, trade and domestic customers. 

The following locations are included within the above scope of certification:- 

Bath 

New Rock, Chilcompton, Radstock, Bath BA3 4GJ 

Tel: +44 (0)1761 232666 • Fax: +44 (0)1761 232647 

Chester 

Dragon Hall, Whitchurch Road, Chowley, Tattenhall, Chester CH3 9DU 

Tel: +44 (0)1829 770776 • Fax: +44 (0)1829 770778 

20 Nov 2011 569



Haes Systems Limited 

Columbia House, Packet Boat Lane, Cowley Peachey, Uxbridge, Middlesex UB8 2JP, United Kingdom 

Tel: +44 (0)1895 422066 • Fax: +44 (0)1895 420603 

E-mail: enquiries@haes-systems.co.uk • Website: www.haes-systems.co.uk 


Scope: 

Design, manufacture and supply of fire detection and alarm system components. 

Hall & Kay Fire Engineering (Manchester) 

10 Westpoint, Clarence Avenue, Trafford Park, Manchester M17 1QS, United Kingdom 

Tel: +44 (0)161 872 7316 • Fax: +44 (0)161 872 7003 

E-mail: Manchester@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 


Hall & Kay Fire Engineering (Paisley) 

Studio 3002, Abbey Mill, Seedhill Road, Paisley PA1 1TJ, United Kingdom 

Tel: +44 (0)141 887 4921 • Fax: +44 (0)141 887 6346 

E-mail: glasgow@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 


Hall & Kay Fire Engineering (Thame) 

Thame Park Road, Thame, Oxfordshire OX9 3RT, United Kingdom 

Tel: +44(0) 1844 265008 • Fax: +44(0) 1844 265008 

E-mail: detection@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 

Design, installation, commissioning & servicing of fire detection, fire alarm and gaseous fire extinguishing systems. 

Hall & Kay Fire Engineering (West Midlands) 

Sterling Park, Clapgate Lane, Woodgate Valley, West Midlands B32 3BU, United Kingdom 

Tel: +44 (0)121 421 3311 • Fax: +44 (0)121 422 7312 

E-mail: birmingham@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 

Design, manufacture and servicing of fire sprinklers, alarm, dry and deluge valves and related products for fire sprinkler systems. 

570 20 Nov 2011



Hall Fire Protection Limited 

Holloway Drive, Wardley Business Park, Worsley M28 2LA, United Kingdom 

Tel: +44 (0)161 793 4822 • Fax: +44 (0)161 794 4950 

E-mail: sales@hallfire.co.uk • Website: www.hallfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. Fabrication of pipework for fire sprinkler systems. 

Hallmark Fire (a division of SFS Fire Services Ltd) 

Systems House, Stoke Road, Hoo, Rochester, Kent ME3 9NT, United Kingdom 

Tel: +44 (0)8700 111150 • Fax: +44 (0)8700 111160 

E-mail: sales@hallmarkfire.co.uk • Website: www.hallmarkfire.co.uk 


Scope: 

Design, installation, commissioning and servicing of fire detection systems, fire alarm systems and gaseous fire extinguishing systems. 

Halton Foodservice Limited 

11 Laker Road, Airport Industrial Estate, Rochester, Kent ME1 3QX, United Kingdom 

Tel: +44 (0)1634 666111 • Fax: +44 (0)1634 666333 

E-mail: kelly.hiley@halton.com • Website: www.halton.com/foodservice 


Scope: 

Design and manufacture of KSA Filters. 

Handan Boate Foundry Co Limited 

Foundry Industry Zone, Jize County, Handan, Hebei Province 057350, China 

Tel: +0310 766 2358 • Fax: +0310 766 2868 

E-mail: hd-baote@tom.com 


Scope: 

Manufacture and machining of grey and ductile iron castings. 



Tel: +44 (0)191 214 0404 • Fax: +44 (0)191 271 1611 



Scope: 

Design, development, manufacture, installation, service and repair of industrial doors, industrial rolling shutters, fire doors and fire rolling 

shutters. 

20 Nov 2011 571



Harvel Plastics Incorporated (Bakersfield) 

7001 Schirra Court, Bakersfield, California 93313, United States 

Tel: +1 661 396 0653 • Fax: +1 661 396 1821 

E-mail: harvel@harvel.com • Website: www.harvel.com 


Scope: 

Manufacture of PVC and CPVC pipes. 

Harvel Plastics Incorporated (Easton) 

300 Kuebler Road, Easton, Pennsylvania 18040, United States 

Tel: + 1 610 252 7355 • Fax: + 1 610 253 4436 

E-mail: harvel@harvel.com 


Scope: 

Manufacture of PVC and CPVC pipe, shapes and ducts. 



Tel: +44 (0)151 426 7171 • Fax: +44 (0)151 493 1331 



Scope: 

Manufacture of thermal insulating and fire resistant composite panels. 

Henry Lewis and Sons (Wireworkers) Limited 

Unit 7, Bolling Road Industrial Estate, Bradford BD4 7HN, United Kingdom 

Tel: +44 (0) 1274 307359 • Fax: +44 (0) 1274 370784 

E-mail: info@henrylewisandson.co.uk • Website: www.henrylewisandson.co.uk 


Scope: 

Manufacture, assembly, installation and repair of physical security products, comprising retractable grilles, shutters, fencing and guards. 

Heras U.K. Fencing Systems 

Herons Way, Balby, Doncaster DN4 8WA, United Kingdom 

Tel: +44 (0)1302 364551 • Fax: +44 (0)1302 322401 

E-mail: enquiries@herasuk.co.uk • Website: www.heras.co.uk 


Scope: 

Design, manufacture and supply of security fencing systems. 

572 20 Nov 2011



Hersey Meters 

Highway 70, Cleveland (Rowan County), North Carolina 27013, United States 

Tel: +1 704 278 2221 • Fax: +1 704 278 9617 

Website: www.herseymeters.com 


Scope: 

Manufacture of water meters and related waterworks products. Manufacture of butterfly valves and check valves. 

Hershey Valve Co Limited 

No 16 Jing 2nd Road, Wuchi, Taichung 435, Taiwan ROC 

Tel: +886 4 2659 5377 • Fax: +886 4 2659 5288 


Scope: 

Production of CPVC, UPVC and plastic pipes, fittings, valves, sheets and cable trays. 

Hilti (Gt Britain) Limited 

1 Trafford Wharf Road, Manchester M17 1BY, United Kingdom 

Tel: +44 (0)161 886 1000 • Fax: +44 (0)161 872 1240 

Website: www.hilti.co.uk 

Freephone: 0800 886 100, Freefax: 0800 886 200 


Scope: 

Stockholding and supply of fire penetration seals, sealants and fire rated foam filler. 

Hochiki America Corporation 

7051 Village Drive, Buena Park, California 90621, United States 

Tel: +1 714 522 2246 • Fax: +1 714 522 2268 

E-mail: sales@hochiki.com • Website: www.hochiki.com 


Scope: 

Manufacture of fire detection and alarm system components. Procurement, distribution and repair of control indicating equipment for fire 

protection. 

Hochiki Corporation 

246 Tsuruma, Machidia, Tokyo 194-8577, Japan 

Tel: +81 3 3444 4111 • Fax: +81 3 3444 4167 

E-mail: info@hochiki.co.jp • Website: www.hochiki.co.jp 

Also at: 

141-1 Maehara, Ejiri, Kakuda, Miyagi 981-1521, Japan 


Scope: 

Machida: 

20 Nov 2011 573



Design of fire and gas leakage alarms. 

Design and manufacture of fire detectors and fire control and indicating equipment. 

Design and manufacture control panels for road tunnels. 

Design and manufacture control panels for fire sprinkler systems. 

Control of outsourcing manufacture for emergency alarm equipment and alarm sounders. 

Design and manufacture of small power radio equipment. 

Scope: 

Miyagi 

Manufacture of point type smoke and heat detectors, optical beam smoke detectors and fire and gas leakage alarms. 

Control of outsourcing manufacture for emergency alarm equipment. 

Manufacture of small power radio equipment. 

Hochiki Europe (UK) Limited 

Grosvenor Road, Gillingham Business Park, Gillingham, Kent ME8 0SA, United Kingdom 

Tel: +44 (0)1634 260133 • Fax: +44 (0)1634 260132 

E-mail: sales@hochikieurope.com 


Scope: 

Design, manufacture, service and maintenance of fire detection and alarm equipment. 

Honeywell Life Safety Systems UK 

140 Waterside Road, Hamilton Industrial Park, Leicester LE5 1TN, United Kingdom 

Tel: +44 (0)116 246 2000 • Fax: +44 (0)116 246 2300 

E-mail: gent_enquiry@gent.co.uk • Website: www.gent.co.uk 


Scope: 


Honeywell Security UK Limited 

Newhouse Industrial Estate, Fire Exit 3, Motherwell, Lanarkshire ML1 5SB, United Kingdom 

Tel: +44 (0)1698 738200 • Fax: +44 (0)1698 738300 

E-mail: hsuk64salesteam@honeywell.com • Website: www.honeywell-security.co.uk 

Repair at: 

Aston Fields Road, Whitehouse Industrial Estate, Runcorn, Cheshire WA7 3DL, United Kingdom 


Scope: 

Design, repair and sales of intruder security products. 

Horing LIH Industrial Co Ltd 

No. 17-6, Ai-Chien Road, Hu-Hsi Village, Yuan-Shan Hsiang (264), Ilan Hsien, Taiwan ROC 

Tel: +886 2 22487599 • Fax: +886 2 22407752 


Scope: 

Design and manufacture of fire detection and alarm components. 

574 20 Nov 2011



Hosiden Besson Limited 

St Joseph's Close Trading Estate, St Joseph's Close, Hove, East Sussex BN3 7EZ, United Kingdom 

Tel: +44 (0)1273 860000 • Fax: +44 (0)1273 777501 

E-mail: info@hbl.co.uk • Website: www.hbl.co.uk 


Scope: 

Design and supply of audible alarm devices. 

Huzhou Jiusheng Electric Co Ltd 

1000 Xifeng Road, Huzhou Economy & Technology Zone, Huzhou, Zhejiang Province 313000, China 

Tel: +86 572 222 8188 • Fax: + 86 572 222 8177 

E-mail: tec@hz-tec.com 


Scope: 

The manufacture and supply of mineral insulated cables not exceeding 500V. 

Iceberg Building Services Limited 

1 Station Court, Station Approach, Wickford, Essex SS11 7AT, United Kingdom 

Tel: +44 (0)1268 739450 • Fax: +44 (0)1268 739439 

E-mail: iceberg@btconnect.com • Website: www.iceberybuildingservices.co.uk 


Scope: 

Design, installation, commissioning and servicing of fire detection and alarm systems. Design, installation and maintenance of air 

conditioning and ventilation systems. 

Icopal S. A. 

Parc Industriel des Hauts Sarts, Rue de Hermee 186, Herstal, Belgium 

Tel: +32 4240 5151 • Fax: +32 4240 5199 



Scope: 

Manufacture and supply of metal roof and cladding systems including accessories. 



Tel: +44 (0)1606 871832 • Fax: +44 (0)1606 871482 



Scope: 

Design, manufacture, installation and servicing of fire rolling shutters and industrial rolling shutters. Installation and servicing of fire doors 

and industrial doors. 

20 Nov 2011 575



Influx Measurements Limited 

1A Bennett House, The Dean, Alresford, Hampshire SO24 9BQ, United Kingdom 

Tel: +44 (0)1962 736736 • Fax: +44 (0)1962 736737 

E-mail: townermark@yahoo.co.uk 


Scope: 

Design and manufacture of direct reading flow meters. 

IPB N.V. 

Steenovenstraat 30, B-8790 Waregem, Belgium 

Tel: +32 56 60 79 19 • Fax: +32 56 61 08 85 


Scope: 

Design, development, manufacture and sales of plastic sheets. 

Irish Driver-Harris Company Limited 

Millbanks, New Ross, Co Wexford, Ireland 

Tel: +353 51 421 405 • Fax: +353 51 422 983 

E-mail: quality@idh.ie 


Scope: 


Irish Industrial Tanks Limited 

Unit C1, Ballymount Drive Industrial Estate, Ballymount Road, Walkinstown, Dublin 12, Ireland 

Tel: +353 1 450 7893 • Fax: +353 1 450 6404 

E-mail: irishind@connect.ie • Website: www.iit.ie 


Scope: 

Supply and installation of water storage tanks. 

Irish Sprinkler & Fire Protection Limited 

Damastown Green, Damastown Industrial Estate, Mulhuddart, Dublin 15, Ireland 

Tel: +353 1 8614036 • Fax: +353 1 8614037 

E-mail: irishsprinkler@joneseng.com • Website: www.joneseng.com 


Scope: 


576 20 Nov 2011





Tel: +44 (0)191 258 5052 • Fax: +44 (0)191 259 5742 



Scope: 

Manufacture of fire resistant and industrial wall and ceiling cladding materials. Manufacture of fire resistant and industrial cold storage 

wall panels. Manufacture of polyisocyanurate foam (PIR) products. 

J & J Design Limited 

Unit 4, Underbank Way, Carrs Industrial Estate, Haslingden, Rossendale, Lancashire BB4 5HR, United 

Kingdom 

Tel: +44 (0)1706 223414 • Fax: +44 (0)1706 225639 

E-mail: Adrian@jjsprinklers.co.uk • Website: www.jjsprinklers.co.uk 


Scope: 


J Durrance & Co Ltd 

Durrance House, 855 London Road, West Thurrock, Essex RM20 3LG, United Kingdom 

Tel: +44 (0)1708 258999 • Fax: +44 (0)1708 258900 

E-mail: sales@jdurrance.co.uk • Website: www.jdurrance.co.uk 


Scope: 

Design, manufacture and installation of pedestrian access security, fire doors and anti bandit screens. Installation and servicing of roller 

shutter and fire doors. 

Also at: 

Unit 3, Hanlon Court, Royal Industrial Estate, Jarrow, Newcastle-upon-Tyne NE32 2HR UK 

Tel: +44 (0)191 428 6000 • Fax: +44 (0)191 483 8787 


Scope: 

Manufacture, installation, service and repair of door, grilles, rolling shutters, fire doors and fire roller shutters. 

J. Bryceland Fire Systems Ltd 

Nobel Road, West Gourdie Industrial Estate, Dundee DD2 4XE, United Kingdom 

Tel: +44 (0)1382 624000 • Fax: +44 (0)1382 624300 

E-mail: jbryceland@aol.com • Website: www.jbrycelandfiresystems.co.uk 


Scope: 

Design, installation and servicing of automatic sprinkler systems. Installation of wet and dry hydrant risers and hose reels. 

20 Nov 2011 577



K.P.F.P. Limited 

59 Pound Street, Carshalton, Surrey SM5 3PG, United Kingdom 

Tel: +44 (0)20 8544 4844 • Fax: +44 (0)20 8544 4819 

E-mail: fire@kpfp.co.uk • Website: kpfp.co.uk 


Scope: 

Design, supply, installation, testing and repair of sprinkler systems, hose reels, hydrants and risers. 

KAC Alarm Company Limited 

KAC House, Thornhill Road, North Moons Moat, Redditch, Worcestershire B98 9ND, United Kingdom 

Tel: +44 (0)1527 406655 • Fax: +44 (0)1527 406677 

E-mail: sales@kac.co.uk OR marketing@kac.co.uk • Website: www.kac.co.uk 


Scope: 

Design and manufacture of manual call points, sounders and sounder strobes. 

Kean Building & Fire Protection Services Limited 

39/43 Temple Bar, Willenhall, West Midlands WV13 1SH, United Kingdom 

Tel: +44 (0)1902 603550 • Fax: +44 (0)1902 608017 

E-mail: kean.fp@btconnect.com 


Scope: 

Design and installation of fire sprinkler systems. 

Kentallen Fire Protection Limited 

Lancaster Road, Lowmoss Industrial Estate, Bishopbriggs, Glasgow G64 2LL, United Kingdom 

Tel: +44 (0)141 762 2540 • Fax: +44 (0)141 762 0823 

E-mail: kentallen@btconnect.com 


Scope: 


Kentec Electronics Limited 

Units 25-27, Fawkes Avenue, Questor, Dartford, Kent DA1 1JQ, United Kingdom 

Tel: +44 (0)1322 222121 • Fax: +44 (0)1322 291794 

E-mail: sales@kentec.co.uk • Website: www.kentec.co.uk 


Scope: 

Design, manufacture, sales and servicing of control panels for fire detection, extinguishing release, sprinkler systems, water and smoke 

detection, associated power supplies, battery chargers and supply of printed circuit assemblies including metal fabrication, powder 

coating and silk screening of enclosures. 

578 20 Nov 2011



Keystone Electric Wire & Cable Company Limited 

#110 D.D. 83, Kwan Ti North Village, Fanling, New Territories, Hong Kong 

Tel: +852 2691 7183 • Fax: +852 2695 9738 

E-mail: sales@keystonecable.com • Website: www.keystonecable.com 


Scope: 

Sales: 

Design and supply of electric wires and cables for use in installations which require safety in the event of fire. 

Dongguan Factory: 

Dongguan Keystone Electric Wire & Cable Company Ltd 

Ye Sha Management District, Shatin, Dongguan City, Guangdong, 

People's Republic of China 

Scope: 

Design, manufacture and supply of electric wires and cables up to 35KV for use in installations which require safety in the event of fire. 

Kidde Products Ltd, trading as AirSense Technology 

Unit 1, Caxton Place, Caxton Way, Stevenage, Hertfordshire SG1 2UG, United Kingdom 

Tel: +44 (0)1462 751296 • Fax: +44 (0)1462 729137 

E-mail: tech@airsense.co.uk • Website: www.airsense.co.uk/airsense 


Scope: 

Design and manufacture of aspirating smoke detectors and supply of aspirating pipe, associated fittings and accessories. 

Kingfell Plc 

Capital Tower, 12th Floor, 91 Waterloo Road, London SE1 8RT, United Kingdom 

Tel: +44 (0)845 60 61 999 • Fax: +44 (0)845 25 81 999 

E-mail: enquiries@kingfell.com • Website: www.kingfell.com 


Scope: 

Design, installation, commissioning and servicing of fire detection and alarm systems. 

Kingspan Door Components S.A. 

Zone Industrielle De L'Europe 1A, 7900 Leuze-En-Hainaut, Belgium 

Tel: +32 (0)69 868222 

Website: www.kingspandoor.com 


Scope: 

The design, manufacture and distribution of PUR/PIR foam filled composite door panels and components. 

20 Nov 2011 579



Kingspan Insulation Limited 

Pembridge, Leominster, Herefordshire HR6 9LA, United Kingdom 

Tel: +44 (0)1544 388601 • Fax: +44 (0)1544 388888 

E-mail: info.uk@insulation.kingspan.com • Website: www.insulation.kingspan.com 

Also at: 

Sherburn Enterprise Park, Enterprise Way, Sherburn-in-Elmet, North Yorkshire LS25 6NA, United Kingdom 


Scope: 

Leomister: 

Design and manufacture of insulated and fire rated flat and tapered rigid polyurethane, polyisocyanurate and phenolic thermal insulation 

boards. Design, manufacture and sales of pre-mitred tapered roof systems. 

Scope: 

Sherburn-in Elmet: 

Manufacture of insulated products. 

Kingspan Ltd 


Tel: +353 42 969 8572 • Fax: +353 42 969 8576/77 



Scope: 

Design and manufacture of fire resistant wall and roof cladding materials and industrial wall and roof cladding materials, multi-beam 

purlins and accessories, gutters, flashing systems and single and double translucent roof lights. 

Kingspan Ltd trading as Kingspan Structural, Kingspan Fabrications, Kingspan 

Controlled Environments (KCE), Kingspan Profiles and Sections 


Tel: +44 (0)1944 710591 • Fax: +44 (0)1944 710777 

E-mail: wbc@wards.co.uk • Website: www.wards.co.uk 


Scope: 

Design and manufacture of foam filled fire resistant insulated panels for roof, wall and cold store applications and ancillaries, cold rolled 

Multi-Beam, rail and channel sections, floor deck profiles; flashings, building ancillaries and architectural façade systems. Design, 

manufacture and installation of Kingframe building systems and cold rolled steel sections. Pre-treatment and protective coating to steel 

and galvanized components for architecturtal and industrial applications. 

Kingspan Ltd. 


Tel: +44 (0)1352 716100 • Fax: +44 (0)1352 716161 



Scope: 

Manufacture of fire resistant and industrial wall and roof cladding materials. 

580 20 Nov 2011



KingspanTarec Industrial Insulation Limited 

Glossop Brook Road, Glossop, Derbyshire SK13 8GF, United Kingdom 

Tel: +44 (0)870 733 0021 • Fax: +44 (0)870 700 0022 

E-mail: info@kingspantarec.co.uk • Website: www.kingspantarec.co.uk 


Scope: 

Manufacture of polyurethane and phenolic rigid foam insulation. 

KME Italy SpA 

Via Della Repubblica 257, 55051 Fornaci Di Barga, Lucca, Italy 

Tel: +39 0583 701.1 • Fax: +39 0583 701623 

E-mail: massimo.banfi@kme.com • Website: www.kme-italy.com 


Scope: 

Manufacture of mineral insulated cables for use in installations that require safety in the event of fire. 




Tel: +44 (0)208 526 8572 • Fax: +44 (0)208 984 0378 


Scope: 

Manufacture, installation and servicing of industrial doors, industrial rolling shutters and fire rolling shutters. 



Tel: +44 (0)191 483 5449 • Fax: +44 (0)191 489 0698 



Scope: 

Manufacture and installation of specialist steel security doors, screens and glazed steel entrance systems. 

Lincs Doors Limited 

Innovation Way, Europarc, Grimsby, North East Lincolnshire DN37 9TT, United Kingdom 

Tel: +44 (0)1472 311057 • Fax: +44 (0)1472 311058 

E-mail: enquiries@lincsdoors.co.uk • Website: www.lincsdoors.co.uk 


Scope: 

Manufacture, supply and installation of industrial and fire doors. 

20 Nov 2011 581



Lingjack Engineering Works PTE Ltd 

No. 1 Woodlands Terrace, #03-01 Lingjack Industrial Building 738471, Singapore 

Tel: +65 6759 4163 • Fax: +65 6758 7513 

E-mail: combat@lingjack.com • Website: www.combat.com.sg 


Scope: 

Manufacture of portable fire extinguishers, fire hose reels, breeching inlets, dry risers, high pressure landing valves and fire fighting hose 

assemblies. Non-ferrous casting, machining and testing process.* 

(*Foundry Address: 35, Jalan Canggih 8, Taman Perindustrian Cemerling, 81800 Ulu Tiram, Johor, Malaysia) 

Linkester Fire Protection Limited 

4/6 Cross Street, Macclesfield, Cheshire SK11 7PG, United Kingdom 

Tel: +44 (0)1625 511272 • Fax: +44 (0)1625 511272 

E-mail: sales.linkester@btconnect.com 


Scope: 

Design, installation and servicing of fire sprinkler and foam systems. 

Lion Steelworks SDN. BHD. 

Lot 4, Solok Waja 3, Kawasan Perindustrian Bukit Raja, 41050 Klang, Selangor, Malaysia 

Tel: +603 3341 3822 • Fax: +603 3342 7630 

E-mail: lion@fmm.jaring.my 


Scope: 

Design and manufacture of safes, strong rooms and secure cabinets. 

Lixil Nittan Company Limited 

1-11-6, Hatagaya, Shibuya-Ku, Tokyo 151-8535, Japan 

Tel: +81 3 3468 1116 • Fax: +81 3 3468 1120 


Scope: 

Design, development of automatic fire detectors, fire alarm control systems, indicating equipment and fire extinguishing equipment 

including management of distribution centres. 

Lixil Nittan Electronic Company Limited 

1 Higashi-Kibogaoka, Asahi-ku, Yokohama, Kanagawa 241-0826, Japan 

Tel: +81 45 364 4751 • Fax: +81 45 363 2678 


Scope: 

Design and manufacture of fire alarm control equipment. 

Also at: 

563-6, 1-Chome, Toyonodai, Otonemachi, Kitasaitama-gun, Saitama, Japan 

1, Aza Minamihata, Kohnoike, Itami, Hyougo 664-0006, Japan 

582 20 Nov 2011



Scope at above addresses: 

Manufacture of automatic fire detectors. 



Tel: +44 (0)117 9637111 • Fax: +44 (0)117 9637111 



Scope: 

Supply and installation of modular security kiosks and cages, perimeter and power fencing, gates, barriers, window barsets and alarm 

ducting. 

LPG Tecnicas en Extincion de Incendios, S.L. 

Mestre Joan Corrales 107-109, 08950 Esplugues de Llobregat, Barcelona, Spain 

Tel: +34 93 480 2925 • Fax: +34 93 473 7492 

E-mail: marketing@lpg.es • Website: www.lpg.es 

Also at: 

Sierra de Guadarrama, 32 Naves A y B, Poligono Industrial San Fernando 1, 28830 San Fernando De 

Henares, Madrid, Spain 

and 

C/ Josep Ros i Ros no. 19A y 19B, Poligono Industrial la Clota, 08740 Sant Andreu de la Barca, Barcelona, 

Spain 

and 

Pol. Ind. La Canaleta, Parcela no. 6 Naves 1 y 2, 25300 Tarrega, Lleida, Spain 


Scope: 

The design and manufacture of gaseous fire suppression components and the periodical maintenance, inspection, test and refilling of gas 

cylinders. 

Lubrizol Advanced Materials Europe B.V.B.A 

Nijverheidsstraat 30, B-2260 Westerlo, Oevel, Belgium 

Tel: +32 14 24 16 11 • Fax: +32 14 24 18 19 


Scope: 

Manufacture, quality control and distribution of Temprite CPVC products. 

20 Nov 2011 583



M & P Fire Solutions Ltd 

Suite 17, The Cubes Offices, Beacon South Quarter, Sandyford, Dublin 18, Ireland 

Tel: +353 1 293 3846/47/48/49 • Fax: +353 1 293 7951 

E-mail: admin@mpfiresolutions.com 


Scope: 


M. J. Quinn Integrated Services Limited 

Oak House, Overbrook Lane, Knowsley Business Park, Knowsley, Merseyside L34 9FB, United Kingdom 

Tel: +44 (0)151 547 8800 • Fax: +44 (0)151 547 8801 

E-mail: enquiries@mjquinn.co.uk • Website: www.mjquinn.co.uk 


Scope: 


M. J. Quinn Integrated Services Limited 

5th Floor, 119 Farringdon Road, London EC1R 3DA, United Kingdom 

Tel: +44 (0)207 239 8750 • Fax: +44 (0)207 239 8751 

E-mail: enquiries@mjquinn.co.uk • Website: www.mjquinn.co.uk 


Scope: 

Design, installation, commissioning and servicing of fire detection, alarm systems and sprinkler systems. 

Mavili Elektronik Ticaret Ve Sanayi A.S. 

Bostanci Dudullu Yolu, Kutup Sok, No. 29 Y Dudullu - Umraniye, Istanbul TR 34775, Turkey 

Tel: +90 216 4664 505 • Fax: +90 216 4664 510 

E-mail: mavili@mavili.com.tr • Website: www.mavigard.com 


Scope: 

Design, manufacture, sale & after sale services of fire & gas detectors, control panels & accessories. 

McAvoy Group Limited 

2 Ferguson Road, Knockmore Hill Industrial Estate, Lisburn, Co Antrim BT28 2FW, United Kingdom 

Tel: +44 (0)870 2408987 • Fax: +44 (0)28 8774 88495 

E-mail: sales@mcavoygroup.co.uk • Website: www.mcavoygroup.com 


Scope: 

Design, manufacture and fabrication of portable modular buildings. 

584 20 Nov 2011



MECE Fire & Security Limited 

Courtlodge, Kemsley Street Road, Bredhurst, Gillingham, Kent ME7 3LS, United Kingdom 

Tel: +44 (0)1634 260607 • Fax: +44 (0)1634 260278 

E-mail: enquiries@mecefireandsecurity.co.uk • Website: www.mecefireandsecurity.co.uk 


Scope: 

Design, installation and servicing of fire alarm, security, access control and CCTV systems. 



Tel: +44 (0)121 544 6124 • Fax: +44 (0)121 552 6793 



Scope: 

Design, manufacture, installation, servicing and repair of industrial doors, industrial rolling shutters, fire doors and fire rolling shutters. 

Mercian Industrial Doors (Southern) Limited 

t/a Mercian Industrial Doors Southern, 10-12 Galleymead Road, Colnbrook, Slough, Berkshire SL3 0EN UK 

Tel: +44 (0)1753 681 020 • Fax: +44 (0)1753 684 842 

Scope: 

Installation, servicing and repair of industrial doors, industrial rolling shutters, fire doors, fire rolling shutters and collapsible gates. 

Manufacture of collapsible gates. 

Mercury Engineering 

Mercury House, Sandyford Industrial Estate, Foxrock, Dublin 18, Ireland 

Tel: +353 1 216 3000 • Fax: +353 1 216 3006 

E-mail: fireprotection@mercury.ie • Website: www.mercury.ie 


Scope: 


Midas Technologies (GB) Limited 

Unit A, Roundhouse Close, Eastern Industry, Peterborough PE1 5TA, United Kingdom 

Tel: +44 (0)1733 342600 • Fax: +44 (0)1733 346672 

E-mail: sales@midastech.co.uk • Website: www.midastech.co.uk 


Scope: 

Manufacture of access covers and general metal fabrication. 

Midland Door Services Limited 

Booth Street, Smethwick, West Midlands B66 2PF, United Kingdom 

Tel: +44 (0)121 565 0022 • Fax: +44 (0)121 565 0055 

E-mail: ralph@mdsind.co.uk • Website: www.mdsind.co.uk 


Scope: 

20 Nov 2011 585



Manufacture, installation, service and repair of all types of door systems. 

MITIE McCartney Fire Protection Limited 

Meiklewood Gate, 35 Meiklewood Road, Glasgow G51 4GB, United Kingdom 

Tel: +44 (0)141 880 2700 • Fax: +44 (0)141 880 2701 

E-mail: fireprotection@mitie.co.uk • Website: www.mitie.co.uk 

Also included within the scope of certification 

Unit 11, Hobbs Cross Business Centre, Hobbs Cross Road, Theydon Garnon, Essex CM16 7NY, United 

Kingdom 

Tel: +44 (0)1992 813 598 • Fax: +44 (0)1992 814 541 

and 

Units 16 & 18, Whitwick Business Centre, Stenson Road, Coalville, Leicestershire LE67 4JP, United Kingdom 

Tel: +44(0)1530 276 166 • Fax: +44(0)1530 276 167 


Scope: 

Design, specification, installation, inspection, servicing and repair of all types of passive fire protection and performance coating systems. 

MITIE Technical Facilities Management Limited (MITIE Fire and Security Systems) 

Ventura House, Ventura Park Road, Tamworth B78 3HL, United Kingdom 

Tel: +44 (0)1827 303251 • Fax: +44 (0)1827 309798 

Website: www.mitie.com 


Scope: 

Design, installation, commissioning and servicing of fire detection and alarm systems. 

Mitsubishi Plastics Inc 

Hiratsuka Factory, 2-1-35 Nishishindo, Hiratsuka City, Kanagawa Prefecture 254-8614, Japan 

Tel: +81 4 6322 8065 • Fax: +81 4 6355 9450 

E-mail: mpi1377@cc.mpi.co.jp • Website: www.mpi.co.jp 

Sales Enquiries: 

1-2-2, Nihonbashi Hongokucho, Chuo-ku, Tokyo 103-0021, Japan 

Tel: +81 3 3279 3455 • Fax: +81 3 3279 6740 

E-mail: asano.hiroki@mf.mpi.co.jp • Website: www.mpi.co.jp 


Scope: 

Design and manufacture of hot press moulded GRP sectional water storage tanks. 

586 20 Nov 2011



Modgal Metal (99) Limited 

Rosh Pina Industrial Park, Rosh Pina 12000, Israel 

Tel: +972 4 691 4222 • Fax: +972 4 691 4202 

E-mail: modgalmetal@modgal-metal.com • Website: www.modgalmetal.com 

Quality System Cert. No. 123 Assessed to ISO 9001 

Scope: 

Manufacture of pipe couplings, fittings and general purpose malleable, ductile and grey iron castings. 

Monarflex 

Lyskaer 10,, DK-2730 Herlev, Copenhagen, Denmark 

Tel: +45 44 88 55 50 • Fax: +45 44 88 55 99 

E-mail: contact@monarflex.com • Website: www.special-fire.com 


Scope: 

Manufacture and supply of reinforced plastic sheeting and special membranes, including related products. 

Morgan Marine Limited 

Llandybie, Ammanford, Carmarthenshire SA18 3GY, United Kingdom 

Tel: +44 (0)1269 850437 • Fax: +44 (0)1269 850656 

E-mail: sales@morgan-marine.com • Website: www.morgan-marine.com 


Scope: 

Design, manufacture and installation of industrial housing, covers and tanks including RF and NEMP screened enclosures and sound 

proof housings in composite materials including plastic, alloys and timber. 

Morley-IAS Fire Systems By Honeywell 

Charles Avenue, Burgess Hill, West Sussex RH15 9UF, United Kingdom 

Tel: +44 (0)1444 230300 • Fax: +44 (0)1444 230888 

E-mail: sales@morleyias.co.uk • Website: www.morley-ias.co.uk 


Scope: 

Design and manufacture of fire detection and alarm systems. 

20 Nov 2011 587



N.V. Joris IDE 


Tel: +44 (0)1928 571 444 • Fax: +44 (0)1928 571 488 

E-mail: division.export@joriside.co.uk • Website: www.joriside.co.uk 

and factories at: 

Kortrijksestraat 505, B-8020 Oostkamp, Belgium 

and 

Bosveldstraat 4, B-8750 Zwevezele, Belgium 


Scope: 

Sales, design, fabrication & supply of steel construction materials (roof & wall panels, roof tiles, technical profiles, galvanized profiles & 

insulating sandwich panels). 

Nanjing Fire Protection Technology Co Limited 

12 Shiyang Road, Baixia District, Nanjing, China 

Tel: 86 25 842 79156 • Fax: 86 25 842 79101 

E-mail: yaoQl@tuna.com.cn 


Scope: 

Manufacture of fire sprinklers. 

National Fire Fighting Manufacturing Company Limited (NAFFCO) 

PO Box 17014, Jebel Ali, Dubai, United Arab Emirates 

Tel: +9714 881 5653 • Fax: +9714 881 6229 

E-mail: natfire@emirates.net.ae • Website: www.naffco.com 


Scope: 

Design, manufacture, installation and servicing of portable fire extinguishers, mobile fire extinguishers, auto extinguishing systems, fire 

hoses, hose reels and fire cabinets. Design and assembly of fire pumps, fire pump sets and fire hydrants. Design, manufacture, 

installation and servicing of water supply systems, fire sprinklers, water spray, foam systems and gaseous fixed fire fighting systems. 

Supply of fire blankets. Manufacture of dry riser inlet boxes to BS 5041-5. 

National Sprinkler Company Limited 

Unit 4B, Fingal Bay Business Park, Balbriggan, Co Dublin, Ireland 

Tel: +353 1 690 4001/4040 • Fax: +353 1 841 7400 

E-mail: info@nationalsprinkler.ie • Website: www.nationalsprinkler.ie 


Scope: 


588 20 Nov 2011



Nexans Turkiye Endustri ve Ticaret A.S. 

Izmir Karayolu Uzeri 6.km, Denizli, Turkey 

Tel: 0090 212 266 0160 • Fax: 0090 212 266 0170 

E-mail: Info.turkey@nexans.com • Website: www.nexans.com.tr 


Scope: 

The manufacture and supply of electric cables and wires, including cables that are used in installations which require safety in the event 

of fire. 

NIBCO Inc 

105 Quality Court, Charlestown, IN 471111-1149, United States 

Tel: +1 812 256 8530 • Fax: +1 812 256 8585 

Also at: 

701, Eisenhower Drive North, Goshen, Indiana 46526, United States 

Tel: +1 574 296 1240 • Fax: +1 574 296 1241 


Scope: 

Manufacture of CPVC fittings for fire sprinkler systems. 

Nields Plastic Company Limited 

Units 1 -2, Foley Works Estate, Hereford HR1 2SF, United Kingdom 

Tel: +44 (0)1432 268341 • Fax: +44 (0)1432 353247 

E-mail: sales@nields.co.uk 


Scope: 

Manufacture of low density polythene film including coloured, printed, anti-static, conductive and flame retardant to customer 

specification: film thickness from 12.5 to 375 microns and widths from 50mm (2 inches) to 1524mm (60 inches). Material supplied on reels 

in the form of lay flat tube, centre folded sheet, double wound sheet, single wound sheet, pre-formed lay flat tube, or converted into bags. 

Nitin Fire Protection Industries Limited 

A-117, T.T.C. Industrial Area, Pawane, Navi Mumbai - 400 701, Maharashtra, India 

Tel: +91 22 7633796 

E-mail: nitinfire@vsni.com 

Also at: 

29, Vadhani Estate, L.B.S. Marge, Ghatkoper (West), Mumbai - 400 086, Maharashtra, India 

And 

D-20/4, T.T.C. Industrial Estate, Turbhe, Navi Mumbai - 400 701, Maharashtra, India 


Scope: 

Procurement and supply of gaseous fire fighting components. Procurement, filling, supply and assembly of gaseous fixed fire fighting 

systems. 

20 Nov 2011 589



Nittan (UK) Limited 

Hipley Street, Old Woking, Surrey GU22 9LQ, United Kingdom 

Tel: +44 (0)1483 769555/8 • Fax: +44 (0)1483 756686 

E-mail: sales@nittan.co.uk • Website: www.nittan.co.uk 


Scope: 

The manufacture of fire detection, alarm and monitoring equipment. 

Nittan Fire Protection System (Zhongshan) Company, Limited 

The 2nd Floor, No. 29 Factory Building, New Concentrated Constructed Quarter, Zhongshan Torch Hi-Tech 

Industrial Dvlpmnt Zone, Zhongshan, Guangdong 528437, China 

Tel: +86 760 828 5700 • Fax: +86 760 828 1000 


Scope: 

Manufacture of smoke detectors and their ancillaries. 

NMC (UK) Limited 

Tafarnaubach Industrial Estate, Tredegar, South Wales NP22 3AA, United Kingdom 

Tel: +44 (0)800 834 704 • Fax: +44 (0)800 834 705 



Scope: 

The manufacture and supply of cellular polymers in extruded tube and profiles form including the supply of foam and polyurethane 

decorative products. The manufacture of fire retardent tubing and profiles. 

No Climb Products Limited 

Edison House, 163 Dixons Hill Road, Welham Green, Hertfordshire AL9 7JE, United Kingdom 

Tel: +44 (0)1707 282760 • Fax: +44 (0)1707 282777 

E-mail: info@noclimb.com • Website: www.noclimb.com 


Scope: 

Design and manufacture of fire detection test equipment. 

Nobel Fire Systems 

Unit 6 Southgate Industrial Estate, Green Lane, Heywood, Lancashire OL10 1ND, United Kingdom 

Tel: +44 (0)1706 625 777 • Fax: +44 (0)1706 625 325 

E-mail: info@nobel-fire-systems.com • Website: www.nobel-fire-systems.com 


Scope: 

Design, supply, installation, commissioning & servicing of gas generator, foam, dry chemical, gaseous, watermist & particulate aerosol fire 

suppression systems. 

590 20 Nov 2011



Northern Ireland Plastics Limited 

39 Shrigley Road, Killyleagh, Co. Down, Northern Ireland BT30 9SR, United Kingdom 

Tel: +44 (0)2844 828753/4 • Fax: +44 (0)2844 828809 

E-mail: info@niplastics.co.uk 


Scope: 

Manufacture of twin wall polypropylene sheet. 

Notifier Fire Systems by Honeywell 

Honeywell Life Safety Systems, Charles Avenue, Burgess Hill, West Sussex RH15 9UF, United Kingdom 

Tel: +44 (0)1444 230300 • Fax: +44 (0)1444 230888 

E-mail: sales@notifiersystems.co.uk • Website: www.notifierfiresystems.co.uk 


Scope: 


Nu-Form Fire UK Limited 

390 Manchester Road, Gollinrod, Bury, Lancashire BL9 5NB, United Kingdom 

Tel: +44 (0)1706 825111 • Fax: +44 (0)1706 827111 

E-mail: info@sprinklersystems.co.uk • Website: www.sprinklersystems.co.uk 


Scope: 


Olympic Fire Protection Limited 

Fire House, Mayflower Close, Chandlers Ford, Eastleigh, Hampshire SO53 4AR, United Kingdom 

Tel: +44 (0)870 608 4350 • Fax: +44 (0)870 608 4351 

E-mail: info@olympicfire.co.uk • Website: www.olympicfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems, hosereels, dry risers and hydrants. 

Pace Technology Co. Limited 

The Sanlian Industrial Estate of Gulao Town, Heshan City, Guangdong Province, China 

Tel: +852 917 66779 • Fax: +852 237 45126 

E-mail: peter_pace36@hotmail.com 


Scope: 

Design and manufacture of blanket control and heating under-blanket and manufacture of carbon monoxide detectors. 

20 Nov 2011 591



Panel Projects Limited 


Tel: +44 (0)117 316 7000 • Fax: +44 (0)117 316 7001 


Scope: 

Manufacture and supply of composite insulation and fire retardant panels. 

Paroc Panel System Oy Ab 

FIN-21600, Parainen, Finland 

Tel: +358 46 876 8000 • Fax: +358 46 876 8702 

E-mail: panelinfo@paroc.com • Website: www.paroc.com 


Scope: 

Manufacture of fire resistant composite panels. 

Patterson Pump Ireland Limited 

Unit 14, Mullingar Business Park, Mullingar, Co Westmeath, Ireland 

Tel: +353 44 47078 • Fax: +353 44 47896 

E-mail: rpelot@ie.pattersonpumps.com • Website: www.ie.pattersonpumps.com 


Scope: 

Design and manufacture of fire pump sets. Manufacture of fire pumps. 

PEL Services Limited 

Belvue Business Centre, Belvue Road, Northolt, Middlesex UB5 5QQ, United Kingdom 

Tel: +44 (0)20 8839 2100 • Fax: +44 (0)20 8841 1948 

E-mail: pel@pel.co.uk • Website: www.pel.co.uk 


Scope: 

Design, supply, installation and commissioning of public address, fire alarm, security and communications equipment. 

Pendle Designs Limited 

Pendle House, Webb Street, Bury, Lancs BL8 1AF, United Kingdom 

Tel: +44 (0)161 764 2252 • Fax: +44 (0)161 763 1429 

E-mail: sprinklers@pendledesigns.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems. Manufacture of fabricated pipework for fire sprinkler systems. 

592 20 Nov 2011



Peripheral Support Services Limited 

Unit 14, Enterprise Court, Rankine Road, Basingstoke, Hampshire RG24 8GE, United Kingdom 

Tel: +44 (0)1256 844 685 • Fax: +44 (0)1256 810 082 

E-mail: sales@pss-firequest.co.uk • Website: www.pss-firequest.co.uk 


Scope: 

Design, manufacture, test and repair of fire control systems, emergency lighting control systems and LST radiator covers and 

accessories. 

Pittway Tecnologica Srl. 

Via Caboto 19/3, 34147 Trieste, Italy 

Tel: +39 040 94 90111 • Fax: +39 040 38 2137 

E-mail: sandro_bonin@systemsensor.com • Website: www.systemsensoreurope.com 

European Sales: 

System Sensor Europe, Life Safety Distribution AG, Wilstrasse 11 (Building U31), CH-8610 Uster, Switzerland 

Tel: +41 44 943 4424 • Fax: +41 44 943 4399 

E-mail: sse.marketing@systemsensor.com • Website: www.systemsensoreurope.com 


Scope: 

Design, development and manufacture of control and signalling devices for fire prevention systems and gas detectors. 

Potter Electric Signal Company 

1609 Park 370 Place, Hazelwood, St Louis, Missouri 63042, United States 

Tel: +1 314 595 6900 • Fax: +1 314 595 6999 

E-mail: info@pottersignal.com • Website: www.pottersignal.com 


Scope: 

Design and manufacture of electric alarm pressure switches and water flow alarm switches. 

Powershield Doors Limited 

21 Ferguson Drive, Knockmore Hill Industrial Park, Lisburn, Northern Ireland BT28 2EX, United Kingdom 

Tel: +44 (0)28 9266 2200 • Fax: +44 (0)28 9260 3600 

E-mail: sales@powershield.co.uk • Website: www.powershield.co.uk 


Scope: 

Manufacture and installation of industrial doors, fire doors and windows. 

Pressex UK Limited 

Kingsway South, Team Valley, Gateshead, Tyne & Wear NE11 0SH, United Kingdom 

Tel: +44 (0)191 497 3430 • Fax: +44 (0)191 497 3431 

E-mail: pressex@responsive-engineering.com • Website: www.responsive-engineering.com 


Scope: 

20 Nov 2011 593



Manufacture and supply of anti duress mechanical and electromechanical devices for ATM security. 



Tel: +44 (0)1733 361511 • Fax: +44 (0)1733 361512 



Scope: 

The design, manufacture and installation of barrier systems. 

Project Fire Products Limited (incorporating Project Fire Engineers) 

Pasturefields Lane Industrial Estate, Pasturefields Lane, Hixon, Staffordshire ST18 0PH, United Kingdom 

Tel: +44 (0)1889 270999 • Fax: +44 (0)1889 270974 

E-mail: sales@projectfire.co.uk • Website: www.projectfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. Assembly, installation and commissioning, repair and 

servicing of water flow switch and alarm valve testing devices. 

Protec Camerfield Limited 

5 Churchill Way, Nelson, Lancashire BB9 6RT, United Kingdom 

Tel: +44 (0)1282 717474 • Fax: +44 (0)1282 717475 

E-mail: camerfield@protec.co.uk • Website: www.protec.co.uk 


Scope: 

Design, installation, service and maintenance of fire sprinkler systems and gaseous extinguishing systems. 

Protec Fire Detection plc 

Protec House, Churchill Way, Nelson, Lancashire BB9 6RT, United Kingdom 

Tel: +44 (0)1282 717171 • Fax: +44 (0)1282 717273 

E-mail: sales@protec.co.uk • Website: www.protec.co.uk 


Scope: 

Design, manufacture, installation, commissioning and servicing of fire detection and alarm systems and components. 

The following locations are included within the scope of certification: 

Swanley 

Unit 4 

White Oak Square 

London Road 

Swanley 

Kent BR8 7AG 

Fareham 

Unit 10 

Fulcrum 4 

Solent Way 

Fareham 

Hampshire PO15 7FT 

594 20 Nov 2011



Leeds 

Unit 1, Ashfield Court 

Whitehall Road 

Leeds LS12 5JB 

Tel: 0845 456 5388 

Cannock 

5 Morston Court 

Blakeney Way 

Kingswood Lakeside 

Cannock 

Staffordshire WS11 8JB 



Tel: +44 (0)1625 855666 • Fax: +44 (0)1625 855601 



Scope: 

The procurement and supply of specialist temporary protection materials and scaffold cladding materials. Flame retardant products for 

building and construction industry. 

Provincial Sprinkler Co. Limited 

Unit 4, Cork Airport Industrial Estate, Kinsale Road, Cork, Ireland 

Tel: +353 (0)21 4965058 • Fax: +353 (0)21 4317425 

E-mail: info@provincial-sprinkler.ie • Website: www.provincial-sprinkler.ie 


Scope: 


Prysmian Cables & Systems Limited 

Energy Cables Unit, Wrexham Industrial Estate, Wrexham LL13 9PH, United Kingdom 

Tel: +44 (0)1978 662345 • Fax: +44 (0)1978 662292 

E-mail: cables.marketing.uk@prysmian.com • Website: www.prysmian.co.uk 


Scope: 

Manufacture of electrical cable for installations that require safety in the event of a fire. 

Prysmian Cables & Systems Ltd 

Energy Cables, Chickenhall Lane, Bishopstoke, Eastleigh, Hants SO50 6YU, United Kingdom 

Tel: +44 (0)8457 678345 • Fax: +44 (0)2380 295465 

E-mail: cables.marketing.uk@prysmian.com • Website: www.prysmian.co.uk 

Overseas: 

Tel: +44 (0)2380 295555 


Scope: 

Design and manufacture of electric cable for use in installations that require safety in the event of fire. 

20 Nov 2011 595



Prysmian Power Cables & Systems Australia Pty Limited 

1 Heathcote Road, Liverpool, Sydney, New South Wales 2170, Australia 

Tel: +61 2 9600 0777 • Fax: +61 2 9600 0303 

Website: www.pirelli.com 


Scope: 

Design and manufacture of cables for use in installations that require safety in the event of fire. 




Tel: +44 (0)1269 851777 • Fax: +44 (0)1269 851747 



Scope: 

The design and manufacture of sheet metalwork, fabrications and security doors. 

Qinhuangdao Taidy Flex-Tech Co. Ltd 

No. 5 Yongdinghe Road, Qinhuangdao Economic & Technology Development Zone, Hebei 066004, China 

Tel: +86 335 8586186 • Fax: +86 335 8586190 

E-mail: taidy@taidy.com • Website: www.taidy.com 


Scope: 

Manufacture of "FlexHead" flexible hoses for fire sprinkler systems. 

Quinn Therm Limited 

Scotchtown, Ballyconnell, Co. Cavan, Ireland 

Tel: +353 49 952 5604 • Fax: +353 49 952 5601 

E-mail: info@quinn-therm.com • Website: www.quinn-therm.com 


Scope: 

Manufacture of flat roof systems. 

R & S Fire & Security Services Limited 

Trafalgar House, 712 London Road, Grays, West Thurrock, Essex RM20 3JT, United Kingdom 

Tel: +44 (0)1708 683040 • Fax: +44 (0)1708 683068 

E-mail: sales@rs-fire.com • Website: www.rs-fire.com 


Scope: 

Design, installation, commissioning and servicing of fire detection and alarm gas extinguishing systems. 

596 20 Nov 2011



RAMCRO S.p.A 

Via Marzorati, 15 - 20014 Nerviano, Milan, Italy 

Tel: +39 0331 406560 • Fax: +39 0331 406559 

E-mail: ramcro@ramcro.it 


Scope: 

Design, manufacture and supply of electric cables including cables used for installations that require safety in the event of fire and the 

supply of fibre optic cables. 

Rapidrop Global Limited 

Rutland Business Park, Newark Road, Peterborough PE1 5WA, United Kingdom 

Tel: +44 (0)1733 847 510 • Fax: +44 (0)1733 553 958 

E-mail: rapidrop@rapidrop.com • Website: www.rapidrop.com 


Scope: 

Design, manufacture and testing of fire protection equipment including fire sprinklers, valves and fire sprinkler systems components sub 

assemblies. Procurement, stockholding and supply of fire system products and manual fire extinguishing equipment. 

Red Rose Fire Protection Limited 

Unit 2, Atlas Foundry Estate, Brieryfield Road, Preston PR1 8SR, United Kingdom 

Tel: +44 (0)1772 822133 • Fax: +44 (0)1772 822144 

E-mail: redrosefp@aol.com 


Scope: 


Reliable Fire Sprinkler Limited 

Unit 25, Birches Industrial Estate, East Grinstead RH19 1XZ, United Kingdom 

Tel: +44 (0)1342 316800 • Fax: +44 (0)1342 314679 

E-mail: gleonard@reliablesprinkler.com • Website: www.reliablesprinkler.com 


Scope: 

Stockholding and supply of fire sprinklers, fire protection valves and related products for fire sprinkler and water spray systems. 

20 Nov 2011 597





Tel: +44 (0)1233 506400 • Fax: +44 (0)1233 506401 


Also included within the scope of certification 

Unit 2, Highpoint Business Village, Henwood, Ashford, Kent TN24 8DH 


Tel: +44 (0)20 7801 4800 • Fax: +44 (0)20 7801 4801 

24 hour Telephone Number: 07000 111333 


Scope: 

Manufacture of security marking devices and registration of items of property. 

RGB Integrated Services Limited 

223-236 Claremont House, Nestle Avenue, Hayes, Middlesex UB3 4SH, United Kingdom 

Tel: +44 (0)208 573 9882 • Fax: +44 (0)208 711 3916 

E-mail: info@rgb-services.com • Website: www.rgb-services.com 


Scope: 

Design, installation, testing, inspection and commissioning of electrical installations and design, installation, commissioning and servicing 

of fire detection and alarm systems. 

RGT Fire Protection Limited 

95 Beaumont Road, Bournville, Birmingham B30 2EB, United Kingdom 

Tel: +44 (0)121 433 5175 • Fax: +44 (0)121 486 1847 

E-mail: info@rgtfire.com 


Scope: 

Design, installation and commissioning of fire sprinkler systems. 

Richmond Fire Engineers Limited 

30 Firby Road, Gallowfields Trading Estate, Richmond, North Yorkshire DL10 4ST, United Kingdom 

Tel: +44 (0)1748 825612 • Fax: +44 (0)1748 825935 

E-mail: Sprinklers@richmondfire.co.uk • Website: www.richmondfire.co.uk 


Scope: 

Design, installation and service of fire sprinkler systems. 

598 20 Nov 2011



RMD Fire Control Limited 

The Coach House, 22 Lower Stone Street, Maidstone, Kent ME15 6LX, United Kingdom 

Tel: +44 (0)1622 682522 • Fax: +44 (0)1622 692675 

E-mail: sprinklers@rmdfire.co.uk • Website: www.rmdfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems, hose reels and dry risers. 

Robust UK Limited 

Brookhouse Way, Brookhouse Industrial Estate, Cheadle, Stoke-on-Trent, Staffordshire ST10 1SR, United 

Kingdom 

Tel: +44 (0)1538 752600 • Fax: +44 (0)1538 752604 

E-mail: sales@robust-uk.com • Website: www.robust-uk.com 

Factory: 

Unit 9B, Blythe Park, Sandon Road, Creswell, Stoke-on-Trent, Staffordshire ST11 9RD, United Kingdom 


Scope: 

Manufacture and supply of doorsets for customers and or published requirements. 



Tel: +44 (0)1656 862621 • Fax: +44 (0)1656 862302 



Scope: 

The design and manufacture of stone wool products and systems. 

Rolland Sprinklers 

Usine de 73410, Mognard, France 

Tel: +33 479 547 250 • Fax: +33 479 547 248 

E-mail: info@rolland-sprinklers.com 


Scope: 

Manufacture of fire sprinklers. 

Ross Fire Protection Limited 

29 Deerdykes View, Westfield, Cumbernauld G68 9HN, United Kingdom 

Tel: +44 (0)1236 738502 • Fax: +44 (0)1236 727977 

E-mail: info@rossfire.co.uk • Website: www.rossfire.co.uk 


Scope: 

Design, installation and service of fire sprinkler and water spray systems. 

20 Nov 2011 599



Rotary Firematic Limited 

5 Trench Road, Mallusk Industrial Estate, Newtownabbey, Co Antrim, Northern Ireland BT36 8XA, United 

Kingdom 

Tel: +44 (0)2890 831200 • Fax: +44 (0)2890 831201 

E-mail: mechanical.contracts@rotarygroup.com 


Scope: 

Design and installation of fire sprinkler systems. Fabrication of pipework for fire sprinkler systems. 

Rotherham CNC Ltd 

Unit 30 Orgreave Close, Dore House Industrial Estate, Handsworth, Sheffield S13 9NP, United Kingdom 

Tel: +44 (0)114 269 9800 • Fax: +44 (0)114 269 7949 

E-mail: sales@rotherhamcnc.f9.co.uk 


Scope: 

Provision of engineered precision components. 

RSM Refko Installations Limited 

Unit 8, Capstan Centre, Thurrock Park Way, Tilbury, Essex RM18 7HH, United Kingdom 

Tel: +44 (0)1375 855500 • Fax: +44 (0)1375 855533 

E-mail: rsmrefko@btconnect.com 


Scope: 

Design, installation and servicing of fire sprinkler systems. Installation of gaseous fire extinguishing systems. 

Ruukki Polska Sp. Z.o.o. 

Lukowska 7/9 Street, Oborniki, Wielkopolskie, 64-600, Poland 

Tel: +48 61 296 8510 • Fax: +48 61 296 8545 

Website: www.ruukki.com 


Scope: 

Sandwich panels with PIR core for external claddings, roof coverings and partition walls. 

S.F.S. FIRE SERVICES LIMITED (trading as Hall & Kay Fire Engineering and Chubb 

Fire Mechanical Division) 

1st Floor, Sefton Lodge, Clewer Hill Road, Windsor SL4 4FT, United Kingdom 

Tel: +44 (0)1753 833444 • Fax: +44 (0)1753 833434 

E-mail: windsor@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems, hydrants, hose reels and dry/wet risers together with the supply and servicing 

of fire extinguishers. Supply of fire fighting products. 

600 20 Nov 2011



S.F.S. Fire Services Ltd, T/A Hall & Kay Fire Engineering 

3 Peerglow Centre, Marsh Lane, Ware, Hertfordshire SG12 9QL, United Kingdom 

Tel: +44 (0)1920 460616 • Fax: +44 (0)1920 461113 

E-mail: cpfware@hkfire.co.uk • Website: www.hkfire.co.uk 


Scope: 




Tel: +44 (0)1929 551100 • Fax: +44 (0)1929 553300 



Scope: 

Manufacture, supply, installation, maintenance and repair of timber door sets. 

Supply, installation, maintenance and repair of domestic physical security products. 

SafeGuard Doors, A Division of Adams Rite Europe Limited 

School Street, Willenhall, West Midlands WV13 3PW, United Kingdom 

Tel: +44 (0))1902 364601 • Fax: +44 (0)1902 364602 

E-mail: sales@safeguarddoors.co.uk • Website: www.safeguarddoors.co.uk 


Scope: 

Manufacture and installation of security, bullet resistant, blast effect and fire doors. 

Safeguard Security, a trade name of WBH Industries 

Unit 5, 229 Torrington Avenue, Coventry CV4 9HN, United Kingdom 

Tel: +44 (0)2476 470 600 • Fax: +44 (0)2476 471 600 

E-mail: info@safeguardsecurity.co.uk • Website: www.safeguardsecurity.co.uk 


Scope: 

Manufacture and installation of sliding security grilles. 

Safety Hi-Tech Srl 

Via Cavour, 96 - 67051 Avezzano (AQ), Italy 

Tel: +39 0863 1940720 • Fax: +39 0863 1940724 

E-mail: mail@safetyhitech.com • Website: www.safetyhitech.com 


Scope: 

Production of components and halocarbon gases for fire suppression systems. 

20 Nov 2011 601



Safety Technology International (Europe) Limited 

Unit 49G Pipers Road, Park Farm Industrial Estate, Redditch, Worcestershire B98 0HU, United Kingdom 

Tel: +44 (0)1527 520999 • Fax: +44 (0)1527 501999 

E-mail: sales@sti-europe.com • Website: www.sti-europe.com 


Scope: 

Design and manufacture of fire indicating equipment including products to protect fire and security equipment from theft and damage. 

Stock holding and supply of third party fire and security equipment. 



Tel: +44 (0)1722 342900 • Fax: +44 (0)1722 338784 




Scope: 

Manufacture, installation and service of aluminium and UPVC windows, doors, conservatories and glazed sealed units. 

Sanwa Yoshida (JiaXing) Construction Material Industry Co., Ltd 

South Xitang Town, Jiashan County, Jiaxing City, Zheijang Province, China 

Tel: +86-573-4565888 • Fax: +86-573-84565988 

E-mail: megaboard@yahoo.cn • Website: www.yangmega.net 


Scope: 

Manufacture of non-combustable high performance building board. 

SAPAG Industrial Valves 

2 Rue du Marais, 80400 Ham, France 

Tel: +33 (0)323 810582 • Fax: +33 (0)323 814300 


Scope: 

Design and manufacture of butterfly valves for fire protection systems application. 

Saudi Factory For Fire Equipment Co. 

New Industrial Area, PO Box 58469, Riyadh 11515, Kingdom of Saudi Arabia 

Tel: +966 1 265 0070 • Fax: +966 1 265 2190 

E-mail: qa@sffeco.com.sa • Website: www.sffeco.com 


Scope: 

Design, manufacture, installation, maintenance, repair and servicing of fire extinguishing systems. Design, installation and maintenance 

of fire detection and alarm systems. Manufacture, installation, repair and servicing of portable fire extinguishers, hose reels and cabinets. 

Assembly of fire pumps, hydrants and controllers for fire pumps. Manufacture of fire doors. 

602 20 Nov 2011



Schlumberger Oilfield UK PLC, Sensor Highway Limited (Schlumberger, 

Southhampton) 

Unit 7, The Quadrangle, Abbey Park Industrial Estate, Romsey, Southampton, Hampshire SO51 9DL, United 

Kingdom 

Tel: +44 (0)1794 529600 • Fax: +44 (0)1794 514931 

Website: www.slb.com 

Also at: 

Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, Hampshire SO51 9DL, United Kingdom 

and 

Unit 8, The Quadrangle, Abbey Park Industrial Estate, Romsey, Hampshire SO51 9DL, United Kingdom 


Scope: 

Design, manufacture and repair of distributed temperature sensor devices. 

Scotshield Limited 

Century House, Chapelhall Industrial Estate, Airdrie, Scotland ML6 8QH, United Kingdom 

Tel: +44 (0)1236 767788 • Fax: +44 (0)1236 762233 

E-mail: sales@scotshield.com 


Scope: 

Design, installation, commissioning and maintenance of fire detection systems. 

Security Blinds Limited 

Units 3 A/B, Hope Street, Thornhill Industrial Estate, Rotherham S60 1LH, United Kingdom 

Tel: +44 (0)1709 363535 • Fax: +44 (0)1709 364512 

E-mail: info@securityblinds.co.uk • Website: www.securityblinds.co.uk 


Scope: 

Design, manufacture and installation of security blinds. 

Sekisui Aqua Systems Company Limited 

77 Kami-Onogo, Iwata City, Shizuoka Prefecture 438, Japan 

Tel: +81 5 3835 0101 • Fax: +81 5 3836 2229 

Website: www.sps-int.com 


Scope: 

Manufacture of GRP sectional water storage tanks. 

20 Nov 2011 603



Select Fire Services Limited 

10 Harolds Road, Harlow, Essex CM19 5BJ, United Kingdom 

Tel: +44 (0)1279 641979 • Fax: +44 (0)1279 641978 

E-mail: info@selectfire.co.uk • Website: www.selectfire.co.uk 


Scope: 



Alban Park, Hatfield Road, St Albans, Hertfordshire AL4 0JJ, United Kingdom 

Tel: +44 (0)1727 837271 • Fax: +44 (0)1727 844053 

E-mail: enquiries@selectaglaze.co.uk • Website: www.selectaglaze.co.uk 


Scope: 

Design, manufacture, installation and service of secondary glazing systems. 



Tel: +44 (0)1689 860757 • Fax: +44 (0)1689 860693 



Scope: 

The manufacture and supply of property marking systems incorporating chemical etching, forensic marking, electronic identification and 

secure asset registration using electronic and hard copy systems. 

Shaanxi J & R Fire Fighting Co Ltd 

Qingyang International Building, No 65, Keji 2nd Road, Gaoxin District, Xi'an, Shaanxi 710075, China 

Tel: +86 29 88332970 • Fax: +86 29 88332680 

E-mail: sales@xajr.com • Website: www.xajr.com 

Factory: 

No. 23, South of Weiyang Road, Jinwei New City, Economic and Technologic Development Zone, Xi'an, 

Shaanxi, China 


Scope: 

Design, manufacture and after service of gas (aerosol) fire-extinguishing systems, accessories and fittings. 

Shakun Polymers Limited 

(Cable Division), Plot No. 4, Silver Industrial Estate, Bhimpore, Patalia Road, Daman 396 210, India 

Tel: +91 260 222 1538 • Fax: +91 260 222 1199 

E-mail: technical@shakunpolymers.com • Website: www.shakuncables.com 


Scope: 

Manufacturing of insulated fire resistant wires and cables. 

604 20 Nov 2011



Shellcast Systems Limited 

Camel House, Six Ashes, Bridgnorth WV15 6ER, United Kingdom 

Tel: +44 (0)1562 750 700 • Fax: +44(0)8712 453 553 

E-mail: technical@shellcast-shutters.co.uk • Website: www.shellcast-shutters.co.uk 


Scope: 

Supply, installation, commissioning, service and repair of security shutters. 

ShenZhen CICAM Manufacturing Co Ltd 

Building 11, Wanxia Industry Garden, Tongfuyu Industry District, Shajing Street, Bao An District, Shenzhen 

518104, China 

Tel: +852 2596 7711 • Fax: +852 2586 1600 

E-mail: sherva.chung@dtechnology.com.hk 


Scope: 

Design and manufacture of radioactive based industrial and domestic smoke detection ionization chambers and components. 

Manufacture of industrial and domestic smoke alarms and associated products. 

Shurjoint Metals Inc. 

No 295, Sec 3, Wantan Road, Wantan Township, Pingtung County, Taiwan ROC 

Tel: +886 8 752 5877 • Fax: +886 8 753 0227 


Scope: 

Manufacture of pipe couplings and fittings. 

Siemens plc, Building Technologies, Fire Safety Division 

Brunel House, Sir William Siemens Square, Frimley, Camberley, Surrey GU16 8QD, United Kingdom 

Tel: +44 (0)1276 696000 • Fax: +44 (0)1276 696133 

E-mail: sales.uk.sbt@siemens.com • Website: www.siemens.co.uk/buildingtechnologies 

Also at: 

7th Floor, Commercial Centre, Lakeside Plaza, Walkmill Lane, Bridgtown, Cannock, Staffordshire WS11 0XE, 


Tel: +44 (0)1543 435500 • Fax: +44 (0)1543 435525 


Scope: 

Frimley:- Design, installation, commissioning and servicing of fire detection, alarm systems and gaseous fire extinguishing systems. 

Service and maintenance of fire sprinkler, deluge, water spray, foam, hose reels and hydrants. 

Cannock:- Design, installation, commissioning and servicing of fire detection, alarm systems and gaseous fire extinguishing systems. 

Maintenance of portable fire extinguishers. 

20 Nov 2011 605



Siemens Switzerland Limited, Building Technologies Division 

International Headquarters, Gubelstrasse 22, CH-6301 Zug, Switzerland 

Tel: +41 (0) 41 724 24 24 • Fax: +41 (0) 41 724 35 22 


Scope: 

Design and manufacture of fire detection and alarm equipment and electronic security equipment. Design and assembly of fire 

extinguishing equipment. 

The following locations are included within the scope of certification:- 

Factory Volketswil 

CH-8604 Volketswil, Switzerland 

Factory Altenrhein 

CH-9423 Altenrhein, Switzerland 

Factory Buc 

F-78531 Buc, France 

Scope: 

Manufacture and repair of fire and security detection and alarm systems and components. 

The following location is included within the scope of certification:- 

Factory Berlin 

D-13629 Berlin, Germany 

SigNET AC Limited 

6 Tower Road, Glover Industrial Park, Washington, Tyne & Wear NE37 2SH, United Kingdom 

Tel: +44 (0)191 417 4551 • Fax: +44 (0)191 417 0634 

E-mail: sales@signet-ac.com • Website: www.signet-ac.co.uk 


Scope: 

Manufacture of voice/PA equipment; audio frequency induction loop equipment. Disabled refuge emergency evacuation equipment. 

Simbars (UK) Limited 

Unit 2, 46 Ashton Vale Road, Ashton, Bristol BS3 2HQ, United Kingdom 

Tel: +44 (0)117 953 1444 • Fax: +44 (0)117 963 1444 

E-mail: info@simbars.co.uk • Website: www.simbars.co.uk 


Scope: 

The design, manufacture and installation of water borehole security kiosks including enclosures and gates. Fabrication of small and 

medium sized metal products used as street furniture for security and pedestrian use. 

606 20 Nov 2011





Tel: +44 (0)1952 585673 • Fax: +44 (0)1952 582816 



Scope: 

The design, manufacture and installation of secure storage enclosures, strongroom doors, associated products and services. 

Solent Fire Protection Services Limited 

12 Heritage Business Park, Heritage Way, Gosport, Hampshire PO12 4BG, United Kingdom 

Tel: +44 (0)2392 510230 • Fax: +44 (0)2392 511510 

E-mail: info@solentfire.co.uk • Website: www.solentfire.co.uk 


Scope: 




Tel: +44 (0)191 587 2287 • Fax: +44 (0)191 518 0703 



Scope: 

Manufacture of rain screen cladding panels, louvre units, gutter flashings, fascia and soffit details and bent metal components for 

construction. Sub-contract metal bending. 

Southern Grille & Gate Limited 

Unit 4, Eagle Trading Estate, 29 Willow Lane, Mitcham, Surrey CR4 4UY, United Kingdom 

Tel: +44 (0)208 640 9989 • Fax: +44 (0)208 640 4108 

E-mail: sales@sgg-ltd.co.uk • Website: www.sgg-ltd.co.uk 


Scope: 

Manufacutre of steel doorsets and collapsible gates, roller shutters and grilles. 

Spears Manufacturing Company Inc 

15853 Olden Street, Sylmar, California 91342, United States 

Tel: +1 818 364 1611 • Fax: +1 818 364 6945 

Website: www.spearsmfg.com 


Scope: 

Design and manufacture of injection moulded pipe fittings and valves. 

20 Nov 2011 607



Specialist Panels UK Limited 

Bolam Business Park, Bassington Drive, Bassington Industrial Estate, Cramlington, Northumberland NE23 

8AD, United Kingdom 

Tel: +44(0) 1670 739116 • Fax: +44(0) 1670 732955 

E-mail: isowall@btinternet.com • Website: www.isowall.org.uk 


Scope: 

Manufacture of structural insulated panels. 

SPIE Fire (A division of SPIE) 

7-14 Great Dover Street, London SE1 4YR, United Kingdom 

Tel: +44 (0)20 7089 7350 • Fax: +44 (0)20 7089 7378 

E-mail: fire.engineering@spiematthewhall.com • Website: www.spiematthewhall.com 


Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. Design and installation of fire detection systems. 

SPIE Fire (A division of SPIE) 

Unit 2, Focus Park, Ashbourne Way, Solihull, West Midlands B90 4QU, United Kingdom 

Tel: +44 (0)121 713 8113 • Fax: +44 (0)121 713 8198/8199 


Quality System Cert. No. 070-2 Assessed to ISO 9001 

Scope: 

Design, installation and servicing of fire sprinkler systems. Small works and servicing of fire detection systems. 

SPIE Matthew Hall 

Level 2, McCafferty House, 99 Firhill Road, Glasgow G20 7BE, United Kingdom 

Tel: +44 (0)141 945 8900 • Fax: +44 (0)141 945 8901 



Scope: 

Design, project management, installation and commissioning of fire suppression systems. 

608 20 Nov 2011



SPP Pumps Limited 

Sales & Services: 

Theale Cross, Pincents Lane, Calcot, Reading, Berkshire RG31 7SP, United Kingdom 

Tel: +44 (0)118 932 3123 • Fax: +44 (0)118 932 3302 

E-mail: solutions@spppumps.com • Website: www.spppumps.com 

Design & Manufacture: 

Crucible Close, Muschet Industrial Park, Coleford, Gloucestershire GL16 8PS, United Kingdom 


Scope: 

Design, manufacture and supply of pumps, pump packages and generator sets, for use in construction, building services, oil and gas, and 

water industries, as well as general industry. Project management and the assembly of pump packages and generators including 

associated documentation. Service and provision of spare parts, repair and maintenance of pumps, valves, compressors and other allied 

equipment. 


Service Centres: 

Tufthorn Avenue, Coleford, Gloucestershire GL16 8PS UK 

Unit 1, Stanstead Road, Eastleigh, Hampshire SO50 4RZ UK 

Greg Street, Reddish, Stockport, Cheshire SK5 7BU UK 

Unit 2, Oakbank, Channel Commercial Park, Queens Road, Belfast, Northern Ireland BT3 9DT 

Scope: 

Installation, service and repair of fire pumps, pump packages and valves. 

PO Box 61491, Jebel Ali, Dubai, United Arab Emirates 

Scope: 

Testing and supply of LPCB approved fire pump sets. 

SPP Pumps Inc., 6716 Best Friend Road, Norcross, GA 30071, United States of America 

Scope: 

Supply and testing of pumps and pump sets. 

SPP Pumps (South Africa) (Pty), 6c Roller Street, Spartan Extension 7, Kempton Park, Gauteng, Johannesburg, RSA. 

Scope: 

Supply, manufacture and repair of pumps and pump sets. 

Sprue Safety Products Ltd 

Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ, United Kingdom 

Tel: +44 (0)2476 323232 • Fax: +44 (0)2476 693610 

E-mail: info@fireangel.co.uk • Website: www.fireangel.co.uk 


Scope: 

Design and supply of domestic photo-electric, ionization smoke detectors and CO alarms. 

20 Nov 2011 609



Stanair Industrial Door Services Limited 

2 Henson Way, Telford Way Industrial Estate, Kettering, Northamptonshire NN16 8PX, United Kingdom 

Tel: +44 (0)1536 482187 • Fax: +44 (0)1536 411799 

E-mail: info@stanair.co.uk • Website: www.stanair.co.uk 

Also at: 

Unit 11, Blundells Road, Bradville, Milton Keynes MK13 7HA, United Kingdom 

Tel: +44 (0)1908 222070 • Fax: +44 (0)1908 222621 


Scope: 

Installation, servicing and repair of industrial doors and fire doors. Installation, servicing and repair of industrial rolling shutters and fire 

rolling shutters. 

Stancold plc 


Tel: +44 (0)117 316 7000 • Fax: +44 (0)117 316 7001 

E-mail: sales@stancold.co.uk • Website: www.stancold.co.uk 


Scope: 

Design, supply and installation of composite insulation and fire retardant panels and panel systems. 

Static Systems Group Plc 

Heath Mill Road, Wombourne, Staffordshire WV5 8AN, United Kingdom 

Tel: +44 (0)1902 895551 • Fax: +44 (0)1902 324969 

E-mail: sales@staticsystems.co.uk • Website: www.staticsystems.co.uk 


Scope: 

Design and manufacture of fire alarm systems. Installation, commissioning and servicing of fire detection and alarm systems. 

Steeltech Systems Limited 

Baris House, Nunn Brook Road, County Estate, Huthwaite, Nottinghamshire NG17 2HU, United Kingdom 

Tel: +44 (0)1623 441442 • Fax: +44(0)1623 441443 


Scope: 

The design and fabrication of Dryvit Fedderlite External Thermal-Insulated Cladding (ETIC) System Panels. 

STO AG 

Ehrenbachstrasse 1, D-79780, Stuhlingen, Germany 

Tel: +49 7744 571440 • Fax: +49 7744 572440 


Scope: 

External wall insulation systems plasters, concrete restoration and paints. 

610 20 Nov 2011



Sunjüt A.S. 

Manufacturing Plant: 

Yesilbayir Mah, Hadimköy Istanbul yolu Cad. No: 59, 34555 P.K Arnavutköy Hadimköy, Istanbul, Turkey 

Tel: +90 216 365 3950 • Fax: +90 216 365 0663 


Scope: 

Manufacture of flame retardant woven material. 



Tel: +44 (0)1233 639039 • Fax: +44 (0)1233 625137 



Scope: 

The design, manufacture, supply and installation of steel security doors, fire doors, commercial doors, industrial doors and louvre 

systems. 

Supra UK Limited 

24 The Furlong, Berry Hill Industrial Estate, Droitwich Spa, Worcestershire WR9 9AH, United Kingdom 

Tel: +44 (0)1905 770333 • Fax: +44 (0)1905 797773 

E-mail: sales@keysafe.co.uk • Website: www.keysafe.co.uk 


Scope: 

Distribution and installation of key safes and cabinets. 

Sure Lock Doors Limited 

Unit 4, Monarch Industrial Estate, 198 Kings Road, Tyseley, Birmingham, West Midlands B11 2AP, United 

Kingdom 

Tel: +44 (0)121 706 8400 • Fax: +44 (0)121 706 4399 

E-mail: sales@surelockdoors.co.uk • Website: www.surelockdoors.co.uk 


Scope: 

Design, manufacture and installation of high security stainless steel and aluminium doors, door sets and interlocking systems. 

20 Nov 2011 611



Surelock McGill Group 

Incorporating: 

Surelock McGill Ltd, 25/26 The Business Centre, Molly Millars Lane, Wokingham, Berks RG41 2QY, United 

Kingdom 

and 

Stafford Bridge Doors Ltd, Beford Road, Pavenham, Bedfordshire MK43 7OS, United Kingdom 


Scope: 

McGill Ltd, Wokingham: 

Design and manufacture of single point and multi point bolting and locking systems, heavy duty hinges and related equipment for fire, 

safety, security, blast and acoustic doors, windows, panels and hatches. 

Stafford Bridge Doors Ltd, Pavenham: 

Design, manufacture, supply and installation of security doors and door sets. 

SuZhou Primetech Electronics Co Limited 

ChunFeng Road, Pan Yang Industrial Park, HuangDai Town, Xiang Cheng District, SuZhou City, JiangSu, 

China 

Tel: +86 512 6571 

E-mail: frankybliu@hotmail.com • Website: www.primetech-sz.com.cn 


Scope: 

Manufacture and repair of smoke, heat and gas detection alarms for domestic use. 

SWS UK 


Tel: +44 (0)1524 772400 • Fax: +44 (0)1524 772411 



Scope: 

Manufacture, installation and repair of industrial shutters, collapsible gates and window bars. 

System Sensor 

3825 Ohio Avenue, Saint Charles, Illinois 60174, United States 

Tel: +1 630 377 6580 • Fax: +1 630 377 7245 

Website: www.systemsensor.com 


Scope: 

Design, manufacture of fire detection and alarm system components. Design and manufacture of waterflow alarm switches. 

612 20 Nov 2011



System Sensor de México S.A. de C.V. 

Ave. Valle del Cedro No. 1681, Parque Industrial Intermex, Ciudad Juárez, Chihuahua, CP 32574, Mexico 

Tel: +52 656 6240479 • Fax: +52 656 6240490 

Website: www.systemsensor.com 

USA Office: 

Tel: +1 630 443 4242 • Fax: +1 630 443 4247 


Scope: 

Design and manufacture of fire detection and alarm system components. Manufacture of gas detection devices. 

System Sensor Fire Detectors 

Volochaevskaya Ulitsa, 40 Building 2, 111033 Moscow, Russian Federation 

Tel: +7 495 937 7985 • Fax: +7 495 937 7983 

E-mail: Moscow@systemsensor.com 


Scope: 

Manufacture and servicing of fire detection and alarm system components. 

System Sensor, Honeywell International (I) PVT. Limited 

Sector 36, Pace City - II, Gurgaon - 122 004, Haryana, India 

Tel: +91 124 6371770 • Fax: +91 124 6371713 

E-mail: anil.chugh@honeywell.com 


Scope: 

Manufacture of fire detection and alarm system components. 

Talentum Developments Limited 

Beal Lane, Shaw, Oldham, Lancashire OL2 8PF, United Kingdom 

Tel: +44 (0)1706 844714 • Fax: +44 (0)1706 882612 

E-mail: info@talentum.co.uk • Website: www.talentum.co.uk 


Scope: 

Design, manufacture and repair of spark and flame detectors. 

TangoRail Limited 

Units 1-3,, Prothero Industrial Estate, Bilport Lane, Wednesbury, West Midlands WS10 0NT, United Kingdom 

Tel: +44 (0)844 8360008 • Fax: +44 (0)844 8360009 

E-mail: info@tangorail.com • Website: www.tangorail.com 


Scope: 

Supply of security fencing. 

and 

20 Nov 2011 613



Herons Way, Balby, Doncaster, DN4 8WA 

Scope: 

Design, manufacture and supply of security fencing systems. 

Taylor Fire Sprinklers Limited 

Unit D, Avondale Way, Wakefield, West Yorkshire WF2 7QU, United Kingdom 

Tel: +44 (0)1924 375971 • Fax: +44 (0)1924 609902 

E-mail: info@taylorfiresprinklers.co.uk • Website: www.taylorfiresprinklers.co.uk 


Scope: 




Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 



Scope: 

Design, manufacture and installation of access covers, doors, gratings, grilles, security enclosures, gas cylinder security devices and 

access systems including flooring, decking, support steel and hand railing. 

Terofire Products 

Lion House, Lion Street, Congleton, Cheshire CW12 4BH, United Kingdom 

Tel: +44 (0)1260 297 578 • Fax: +44 (0)1260 290 078 

E-mail: sales@terofire.com • Website: www.terofire.com 


Scope: 

Stockholding and supply of fire alarm control and indicating equipment. Repair of control and indicating equipment. 

Thameside Fire Protection Co. Limited 

Unit 4, Sovereign Business Park, Cranes Farm Road, Basildon, Essex SS14 3JD, United Kingdom 

Tel: +44 (0)1268 597999 • Fax: +44 (0)1268 597998 

E-mail: enquiries@thamesidefire.co.uk • Website: www.thamesidefire.co.uk 


Scope: 

Design, installation and servicing of fire sprinkler systems. Installation, repair and servicing of portable fire extinguishers. Fire alarm 

installation and servicing. 

The Reliable Automatic Sprinkler Co., Inc, 

1470 Smith Grove Road, Liberty, South Carolina 29657, United States 

Tel: +1 864 843 1734 • Fax: +1 864 843 1418 

E-mail: jcevallos@reliablesprinkler.com • Website: www.reliablesprinkler.com 


Scope: 

Design and manufacture of fire sprinklers, alarm, dry and deluge valves and related products for fire sprinkler systems. 

614 20 Nov 2011



The Rooflight Company 

Wychwood Business Centre, Milton Road, Shipton-under-Wychwood, Oxfordshire OX7 6XU, United Kingdom 

Tel: +44 (0)1993 833108 • Fax: +44 (0)1993 831066 

E-mail: info@therooflightcompany.co.uk • Website: www.therooflightcompany.co.uk 

Also at: 

Bourton Industrial Park, Bourton on the Water, Gloucestershire GL54 2HQ, United Kingdom 


Scope: 

Design, manufacture, storage and distribution of pitched and flat rooflights. 

The Viking Corporation 

210 N Industrial Park, Hastings, Michigan 49058, United States 

Tel: +1 269 945 9501 • Fax: +1 269 945 9599 

E-mail: techsvcs@vikingcorp.com • Website: www.vikingcorp.com 

Also at: 

11305 James Street, Holland, Michigan 49424, United States 


Scope: 

Design and manufacture of fire sprinklers, fire protection valves and related products for fire sprinkler systems. 

Thermotech Fire Protection Limited 

Unit 10, Bamford Business Park, Off Hibbert Street, Reddish, Stockport SK4 1PL, United Kingdom 

Tel: +44 (0)161 476 5551 • Fax: +44 (0)161 476 2998 

E-mail: info@thermotech-fireprotection.co.uk • Website: www.thermotech-fireprotection.co.uk 


Scope: 


Tindall Engineering Limited 

Abryll House, Wright Street (off Yorkshire Street), Oldham, Lancashire OL1 3TF, United Kingdom 

Tel: +44 (0)161 620 0666 • Fax: +44 (0)161 620 3966 


Scope: 

Design, manufacture and supply of the MICO range of emergency exit hardware and high security multi-point locking hardware. 

Total Polyfilm Limited 

Armytage Road, The Industrial Estate, Brighouse, West Yorkshire HD6 1PT, United Kingdom 

Tel: +44 (0)1484 714313 • Fax: +44 (0)1484 720452 


Scope: 

Manufacture and supply of low density flame retardant polythene sheeting. 

20 Nov 2011 615



Tratos Cavi SpA 

Via Stadio 2, Pieve S. Stefano 52036, Arezzo, Italy 

Tel: +39 0575 7941 • Fax: +39 0575 798026 

E-mail: direzione@tratos.it • Website: www.tratos.it 


Scope: 

Design, manufacture and supply of electric cables for use in fire alarm systems. 



Tel: +27 31 500 4301 • Fax: +27 31 507 2129/3973 


Scope: 

Design and manufacture of sliding security gates. 

Trimetals Limited 

Sunrise Business Park, Higher Shaftesbury Road, Blandford Forum, Dorset DT11 8ST, United Kingdom 

Tel: +44 (0)1258 459441 • Fax: +44 (0)1258 480408 

E-mail: sales@trimetals.co.uk • Website: www.trimetals.co.uk 


Scope: 

Design and manufacture of bicycle stores. 

Twinplast Limited 

Unit 2, Greycaine Road, Watford, Hertfordshire WD24 7GP, United Kingdom 

Tel: +44 (0)1923 230191/817761 • Fax: +44 (0)1923 817756 

E-mail: sales@twinplast.co.uk • Website: www.twinplast.co.uk 


Scope: 

Manufacture of polypropylene twinwall sheet and associated conversion products. 

Tyco Building Services Products B.V. 

Kopersteden 1, 7547 TJ Enschede, The Netherlands 

Tel: +31 53 4284444 • Fax: +31 53 4283377 

E-mail: info-NL@tyco-bspd.com • Website: www.tycobuilding.com 


Scope: 

Scope: 

Stockholding, supply and distribution of fire protection equipment including: 

-Sprinklers, valves and accessories 

-Hydrants, foam extinguishing system components 

-Pipe couplings, fittings and hangers 

-Metal framing and support systems to distributors and the construction industry 

-Assembly and test of fire protection valve stations 

616 20 Nov 2011



Central Spraysafe / Spraysafe Automatic Sprinklers Limited 

Unit 6, Westpoint Enterprise Park, Clarence Avenue, Trafford Park, Manchester M17 1QS, UK 

Tel: +44 (0)161 875 0400 Fax: +44 (0)161 875 0491 

Scope: 

Supply of fire protection equipment. Assembly and pressure test of valve stations. 

Tyco Fire & Building Products 

Research & Development Center, 1467 Elmwood Avenue, Cranston, RI 02910, United States 

Tel: +1 401 781 8220 • Fax: +1 401 781 7317 


Scope: 

Research, design, development and manufacturing support for the fire protection equipment, pipe couplings, fittings, related piping 

system components and CPVC pipe and fitting manufactures of Tyco Fire and Building Products. 


8902 North Interstate 27, Lubbock, Texas 79403, United States 

Tel: +1 806 472 2400 • Fax: +1 806 806 8902 


Scope: 

Manufacture of fire sprinklers and sprayers. 


245 Swancott Road, Madison, Alabama 35756, United States 

Tel: +1 256 464 5633 • Fax: +1 256 464 5635 


Scope: 

Design and manufacture of CPVC pipe and fittings. 


260 Central Castings Drive, Anniston, AL 36206, United States 

E-mail: info-uk@tyco-bspd.com • Website: www.tycobuilding.com 


Scope: 

Design and manufacture of pipe couplings, fittings, related piping systems components and castings. 



Tyco Park, Grimshaw Lane, Newton Heath, Manchester M40 2WL, United Kingdom 

Tel: +44 (0)161 205 2321 • Fax: +44 (0)161 455 4459 



Scope: 

Design, installation, servicing and inspection of fire sprinklers, detection, deluge, water spray, foam and gas suppression systems. 


20 Nov 2011 617



Belfast 

Tyco House, 13a Airport Road West, Belfast, Northern Ireland BT8 9ED 

Birmingham 

Hawthorns Business Centre, Halfords Lane, Smethwick, Warley, West Midlands B66 1DW 

Bristol 

1610 Park Avenue, Aztec West, Almondsbury, Bristol BS32 4UA 

Dudley 

Hillcrest Business Park, Cinderbank, Dudley, West Midlands DY2 9AP 

Manchester 

Tyco Park, Grimshaw Lane, Newton Heath, Manchester M40 2WL 

Slough 

Tyco House, 57-63 Farnham Road, Slough, Berkshire SL1 3TN 

Swansea 

Tyco House, Phoenix Way, Swansea SA7 9EQ 

Scope: 

Design, installation, servicing and inspection of fire sprinklers, water spray and foam systems. 


East Kilbride 

30-32 Singer Road, Kelvin Industrial Estate, East Kilbride, Lanarkshire G75 0XS 

Newcastle 

6 Stirling Court, Eleventh Avenue North, Team Valley Trading Estate, Gateshead, Tyne & Wear NE11 0JF 

Scope: 

Manufacture, installation, servicing and repair of industrial rolling shutters, fire doors, fire rolling shutters and glazed automatic doors. 


Barnsley (Doors) 

Albion Road, Carlton Industrial Estate, Barnsley, South Yorkshire S71 3HW 

Manchester (Doors) 

Tyco Park, Newton Heath, Manchester M40 2WL 

Wigan (Doors) 

Unit 4, Bradley Hall Trading Estate, Bradley Lane, Standish, Wigan, Lancashire WN6 OXQ 

Scope: 

The contract service and maintenance of portable fire extinguishers within the UK, at each location and in accordance with BS 5306:3, 

BS 5306:8. 


Crayford 

Unit L, Acorn Business Park, Crayford, DA1 4FL 

East Kilbride 

30-32 Singer Road, Kelvin Industrial Estate, East Kilbride, Lanarkshire G75 0XS 

Birmingham 

Hawthorns Business Centre, Halfords Lane, Smethwick, Warley, West Midlands B66 1DW 

618 20 Nov 2011



Manchester 

Tyco Park, Grimshaw Lane, Newton Heath, Manchester M40 2WL 

Tyco Fire Products Manufacturing Limited 

Stockport Trading Estate, Yew Street, Stockport, Cheshire SK4 2JW, United Kingdom 

Tel: +44 (0)161 429 3400 • Fax: +44 (0)161 477 6729 

E-mail: tycofireproducts.uk@tyco-bspd.com • Website: www.tycobuilding.com 

Sales Enquiries: 

Tel: +44 (0)161 8750400 • Fax: +44 (0)161 8750491 


Scope: 

Design and manufacture of fire protection valves, fire sprinklers, high and medium velocity nozzles and controls. Design, manufacture 

and assembly of foam and gas fire extinguishing systems. Manufacture of fusible links. 

Tyco Flow Control (M) Sdn. Bhd. (Tyco Fire Suppression & Building Products, 

Malaysia) 

Lot 886, C1 & C2,, Jalan Subang 9, Taman Perindustrian Subang, 47500 Subang, Selangor, Malaysia 

E-mail: info-uk@tyco-bspd.com • Website: www.tycobuilding.com 


Scope: 

Assembly of couplings and marketing of couplings and fittings. 

Tyco Thermal Controls UK Ltd 

3 Rutherford Road, Stephenson Industrial Estate, Washington, Tyne & Wear NE37 3HX, United Kingdom 

Tel: +44 (0)191 419 8200 • Fax: +44 (0)191 419 8201 

E-mail: jjones@tycothermal.com • Website: www.tycothermal.com 


Scope: 

Design, manufacture and supply of mineral insulated and flexible cables and assemblies for use in heating, temperature measurement, 

wiring, displacement measurement, leak detection, signal transmittal and nuclear applications. Design, supply and installation of heat 

tracing systems. 

UK Fire Safety Limited 

13-15 Lostock Road, Urmston, Manchester M41 0ES, United Kingdom 

Tel: +44 (0)161 746 8037 • Fax: +44 (0)161 746 8136 

E-mail: mroyle@uk-firesafety.co.uk • Website: www.uk-firesafety.co.uk 


Scope: 

Design, supply, installation, servicing and commissioning of fire sprinkler systems. 

20 Nov 2011 619



UK Firewatch Limited 

10 Apollo Court, Koppers Way, Monkton Business Park South, Hebburn, Tyne & Wear NE31 2ES, United 

Kingdom 

Tel: +44 (0)191 495 9525 • Fax: +44 (0)191 495 9529 

E-mail: enquiries@ukfirewatch.com • Website: www.ukfirewatch.com 


Scope: 

Design, fabrication, installation and maintenance of fixed fire protection systems. 

UK Firewatch Limited 

37/39 Manor Road, Romford, Essex RM1 2TL, United Kingdom 

Tel: +44 (0)1708 756248 • Fax: +44 (0)1708 769315 

E-mail: enquiries@ukfirewatch.com • Website: www.ukfirewatch.com 


Scope: 

Design, fabrication, installation and servicing of fire sprinkler and water spray systems, hydrants and hosereels. 

Ultra Suppression Systems Limited 

Oakridge House, Wellington Road, High Wycombe, Buckinghamshire HP12 3PR, United Kingdom 

Tel: +44 (0)1494 444123 • Fax: +44 (0)1494 444345 

E-mail: info@ultrass.co.uk • Website: www.ultrass.co.uk 


Scope: 

Design and project management of water mist and gaseous fire suppression systems including installation, commissioning, service and 

repair. 

Universal Fixings Limited 

New John Street, Halesowen, West Midlands B62 8HT, United Kingdom 

Tel: +44 (0)1384 422284 • Fax: +44 (0)1384 897446 


Scope: 

Manufacture of Filbow Hangers. 

UTC Fire & Security (Africa) trading as Ziton 

Ziton House, 555 Voortrekker Road, Maitland 7405, Cape Town, South Africa 

Tel: +27 21 5066000 • Fax: +27 21 5066100 

Website: www.utcfireandsecurity.com 


Scope: 

Manufacture of fire detection and alarm systems and components. 

620 20 Nov 2011



UTC Fire & Security Americas Corporation, Inc. 

129 North Main Street, Pittsfield, ME 04967, United States 

Tel: +1 207 487 3104 • Fax: +1 207 487 5526 

E-mail: leon.newsome@ge.com • Website: www.gesecurity.com 

8985 Town Center Parkway, Bradenton FL 34202, United States 

Tel: +1 941 739 4200 • Fax: +1 941 751 6384 

41 Woodford Avenue, Plainville CT 06062, United States 

Also at: 

Technology Center, 129 Hunnewell Avenue, Pittsfield ME 04967, United States 


Scope: 

Design, manufacture and repair of fire detection, fire alarm control and indicating equipment, and customer training. 

UTC Fire & Security Services 

10 Avenue du Centaure, B.P.38408-95806, Cergy-Pontoise Cedex, France 

Tel: +33 1 30173737 • Fax: +33 1 30173707 

Website: www.chubbsecurite.com 


Scope: 

Design and manufacture of fire detection and alarm system panels. 

Ventcroft Limited 

Goddard Road, Astmoor Industrial Estate, Runcorn, Cheshire WA7 1NQ, United Kingdom 

Tel: +44 (0)1928 581098 • Fax: +44 (0)1928 581099 

E-mail: sales@ventcroft.co.uk • Website: www.ventcroft.co.uk 


Scope: 

Design and manufacture of electric cables for use in security alarm systems and installations that require safety in the event of fire. 

Victaulic Company 

2010 Enterprise Drive NE, Leland, North Carolina 28451, United States 

Tel: +1 910 371 5588 • Fax: +1 910 371 2728 

E-mail: victaulic@victaulic.co.uk • Website: www.victaulic.com 


Scope: 

Manufacture of press fit pipe couplings and fittings; elastomeric gaskets and fire sprinklers and accessories. 

20 Nov 2011 621



Victaulic Company 

4901 Kesslersville Road, Easton, Pennsylvania 18040, United States 

Tel: +1 610 559 3300 • Fax: +1 610 250 8817 

E-mail: victaulic@victaulic.com • Website: www.victaulic.com 


Scope: 

Design of pipe couplings, fittings, valves, fire sprinklers, grooving tools and related accessories. Manufacture of pipe couplings, fittings, 

valves and related accessories. 

Also at: 

8023 Quarry Road, Alburtis, Pennsylvania 18011, USA 

Scope: 

Casting of pipe couplings, fittings and related accessories. 

And: 

1818 Vultee Street, Allentown, Pennsylvania 18103, USA 

Scope: 

Finishes of pipe couplings and fittings for the water supply industry. 

And: 

Mold Technology Centre (MTC), 2860 Bath Pike, Suite 300, Nazareth, Pennsylvania 18064, USA 

Scope: 

Design and manufacture of elastomeric molds. 

Viking Plastics 

202 Industrial Drive, Huntsville AL 35811, United States 

Tel: 001 256 858 3711 • Fax: 001 256 858 3775 

E-mail: techsvcs@viking.com • Website: www.vikingcorp.com 


Scope: 

Manufacture of CPVC fire sprinkler pipe. 

Vimpex Limited 

Star Lane, Great Wakering, Essex SS3 0PJ, United Kingdom 

Tel: +44 (0) 1702 216999 • Fax: +44 (0) 1702 216699 

E-mail: sales@vimpex.co.uk • Website: www.vimpex.co.uk 


Scope: 

Design, sub-contract manufacture and distribution of fire alarm warning and evacuation devices, including voice-enhanced sounders and 

water leak detection systems. Stockholding, distribution, repair and servicing of tools for the emergency services, police and the military. 

Portable fire fighting equipment, telescopic masts and commercial vehicle accessories. 

622 20 Nov 2011



Vipond Fire Protection Limited 

10-12 Glenfield Road, Kelvin Industrial Estate, East Kilbride, Lanarkshire G75 0RA, United Kingdom 

Tel: +44 (0)1355 2375 25/80/88 • Fax: +44 (0)1355 263399 

E-mail: admin.uk@vipondltd.co.uk • Website: www.vipondfire.co.uk 


Scope: 

Design, installation, and servicing of fire sprinkler systems. Design, installation, commissioning and servicing of fire detection and alarm 

systems. Fabrication of pipework for the sprinkler systems and pipework for carrying fluids. 

Vulcan Tanks Limited 

Cotes Park Lane, Cotes Park Industrial Estate, Alfreton, Derbyshire DE55 4NJ, United Kingdom 

Tel: +44 (0)1773 835321 • Fax: +44 (0)1773 836578 

E-mail: info@cstvulcan.com • Website: www.cstvulcan.com 


Scope: 

Design, manufacture and installation of fire sprinkler water tanks and industrial storage tanks. 

Wagner Group GmbH 

Schleswigstraße 5, D-30853 Langenhagen, Germany 

Tel: +49 511 97383 0 • Fax: +49 511 73338 6 

E-mail: info@wagner.de • Website: www.wagner.de 

Also at: 

Hanseatenstrasse 52, D-30853 Langenhagen, Germany 


Scope: 

Design, production and distribution of fire detection, fire suppression, fire prevention, risk management, intrusion monitoring and alarm 

systems. 

WOPF Befestigungselemente GmbH 

Luner Rennbahn 22, D-21339 Luneburg, Germany 

Tel: +49 4131 30110 • Fax: +49 4131 301198 

Website: www.wopf.de 


Scope: 

Development & manufacture of brackets & pipe support systems. 

Wrexham Mineral Cables 

Wynnstay Technology Park, Ruabon, Wrexham, Clwyd LL14 6EN, United Kingdom 

Tel: +44 (0)1978 810789 • Fax: +44 (0)1978 821502 

E-mail: sales@wrexhammineralcable.com • Website: www.wrexhammineralcables.com 


Scope: 

Manufacture of mineral insulated cables and their terminations with a rated voltage not exceeding 750V. 

20 Nov 2011 623



Writech Industrial Services Limited 

Also including Writech Manufacturing Limited, Mullingar Business Park, Mullingar, Co. Westmeath, Ireland 

Tel: +353 44 9349857 • Fax: +353 44 9349858 

E-mail: info@writechltd.com 


Scope: 

Design, manufacturing, installation, commissioning and servicing of fire sprinkler systems. 

Xi'an System Sensor Electronics Limited 

28 Tuan Jie South Road, Xi'An Hi-Tech Development Zone, Xi'An, Shaan Xi 710075, China 

Tel: +86 29 5246253 • Fax: +86 29 5239673 

E-mail: xf_zhang@systemsensor.com.cn 

Also at: 

40# Zhangbar Er Road, National Xi'an Hi-Tech Industrial Development Zone, Xi'an, China 

Tel: +86 29 85387800 • Fax: +86 29 88332796 


Scope: 

Design, manufacture and repair of fire detection and alarm system components. Manufacture of water flow alarm switches. 

Xtratherm Limited 

Kells Road, Navan, Co. Meath, Ireland 

Tel: +353 46 906 6000 • Fax: +353 46 906 6090 



Scope: 

Manufacture of rigid foam insulation. 

Xtratherm UK Limited 

Park Road, Holmewood Industrial Park, Holmewood, Chesterfield, Derbyshire S42 5UY, United Kingdom 

Tel: +44 (0)1246 858100 • Fax: +44 (0)1246 857447 



Scope: 


Zeta Alarm Systems by GLT Exports Limited 

Detection House, 72-78 Morfa Road, Swansea SA1 2EN, United Kingdom 

Tel: +44 (0)1792 455175 • Fax: +44 (0)1792 455176 

E-mail: ghassan@gltexports.com • Website: www.gltexports.com 


Scope: 


624 20 Nov 2011


ENVIRONMENTAL SYSTEMS 

Businesses face a growing number of environmental pressures including: 

Energy prices 

Water prices 

Concerns from the public about pollution, climate change and resources 

Legislation 

Environmental Taxes (climate change levy, landfill tax etc) 

Waste disposal 

Environmental impact assessment 

Prosecution 

ISO 14001 is a clear way of demonstrating a company’s commitment to the ‘green’ culture, and provides an 

assurance to the public, regulators and purchasers that the environmental policies and procedures the 

company puts into place help to:- 

 

 

 

 

 

Address public concerns 

Reduce risk of legal non-compliance (Environmental Protection Act 1990 and a whole host of others) 

Reduce costs and tax burden (Climate Change Levy and rebates) 

Improve reputation and marketability 

Manage environmental performance 

Assessment and evaluation of environmental management systems can lead to products, systems and 

services that directly improve the quality of life through cleaner, safer and healthier environments. 

Apollo Fire Detectors Limited 

36 Brookside Road, Havant, Hampshire PO9 1JR, United Kingdom 

Tel: +44 (0)2392 492412 • Fax: +44 (0)2392 492754 

E-mail: enquiries@apollo-fire.co.uk 

Quality System Cert. No. EMS 010 Assessed to ISO 14001:2004 

Scope: 

Design and manufacture of fire detection equipment. 

Hochiki Europe (UK) Limited 

Grosvenor Road, Gillingham Business Park, Gillingham, Kent ME8 0SA, United Kingdom 

Tel: +44 (0)1634 260133 • Fax: +44 (0)1634 260132 

Website: www.hochikieurope.com 


Scope: 

Design, manufacture, service and maintenance of fire detection and alarm equipment. 

J W Singer 

Handlemaker Road, Frome, Somerset BA11 4RW, United Kingdom 

Tel: +44 (0)1373 462201 • Fax: +44 (0)1373 473156 

E-mail: enquiries@jwsinger.com • Website: www.jwsinger.com 


Scope: 

Manufacture of brass sprinkler heads for the fire protection industry. 

20 Nov 2011 625



Kingspan Ltd 


Tel: +353 42 969 8572 • Fax: +353 42 969 8576/77 



Scope: 


purlins and accessories, gutters, flashing system and single and double translucent roof lights. 




Tel: +44 (0)1944 710591 • Fax: +44 (0)1944 710777 



Scope: 





Kingspan Ltd. 


Tel: +44 (0)1352 716100 • Fax: +44 (0)1352 716161 



Scope: 


KingspanTarec Industrial Insulation Limited 

Glossop Brook Road, Glossop, Derbyshire SK13 8GF, United Kingdom 

Tel: +44 (0)870 733 0021 • Fax: +44 (0)870 700 0022 

E-mail: info@kingspantarec.co.uk • Website: www.kingspantarec.co.uk 

Quality System Cert. No. EMS 035-2 Assessed to ISO 14001:2004 

Scope: 

Manufacture of polyurethane and phenolic rigid foam insulation. 

Project Fire Products Limited (incorporating Project Fire Engineers) 

Pasturefields Lane Industrial Estate, Pasturefields Lane, Hixon, Staffordshire ST18 0PH, United Kingdom 

Tel: +44 (0)1889 270999 • Fax: +44 (0)1889 270974 

E-mail: sales@projectfire.co.uk • Website: www.projectfire.co.uk 

Quality System Cert. No. EMS 060 Assessed to ISO 14001 

Scope: 

Design, installation and servicing of fire sprinkler and water spray systems. Assembly, installation and commissioning, repair and 

servicing of water flow switch and alarm valve testing devices. 

626 20 Nov 2011





Tel: +44 (0)1625 855666 • Fax: +44 (0)1625 855601 


Tel: 0800 834 704 • Fax: 0800 834 705 


Scope: 

The procurement and supply of specialist temporary protection materials including LPS 1207 and LPS 1215 flame retardant products for 

the building and construction industry. 

Ruskin Air Management Limited 

Joseph Wilson Industrial Estate, South Street, Whitstable, Kent CT5 3DU, United Kingdom 

Tel: +44 (0)1227 276100 • Fax: +44 (0)1227 264262 


Also at: 

Stourbridge Road, Bridgnorth, Shropshire WV15 5BB, United Kingdom 


Scope: 

Manufacture and supply of fire protection, weather protection and air distribution products. 



Tel: +44 (0)1929 551100 • Fax: +44 (0)1929 553300 


Quality System Cert. No. EMS 835 Assessed to ISO 14001 

Scope: 

Manufacture, supply, installation and repair of timber doors. Supply installation, maintenance and repair of domestic physical security 

products. 

SPP Pumps Limited 

Theale Cross, Pincents Lane, Calcot, Reading, Berkshire RG31 7SP, United Kingdom 

Tel: +44 (0)118 932 3123 • Fax: +44 (0)118 932 3302 

E-mail: solutions@spppumps.com • Website: www.spppumps.com 


Scope: 

Design, manufacture and supply of pumps, pump packages and generator sets for use in construction, building services, oil and gas and 

water industries as well as general industry. Project management and the assembly of pump packages and generators including 

associated documentation. Service and provision of spare parts, repair and maintenance of pumps, valves, compressors and other allied 

equipment. 

Sites covered by this Approval: 

Sales & Service Centre: Theale Cross, Pincents Lane, Calcot, Reading, Berkshire RG31 7SP UK 

Design & Manufacture : Crucible Close, Muschet Industrial Park, Coleford, Gloucestershire GL16 8PS UK 

Service Centre: Tufthorn Avenue, Coleford, Gloucestershire GL16 8PJ UK 

Service Centre: Unit 2, Oak Bank, Channel Commercial Park, Belfast, Northern Ireland BT3 9DT 

20 Nov 2011 627



Service Centre: Unit 1, Stanstead Road, Eastleigh, Hampshire SO50 4RZ UK 

Service Centre: Greg Street, Reddish, Stockport, Cheshire SK5 7BU UK 



Tel: +44 (0)1938 555511 • Fax: +44 (0)1938 555527 



Scope: 

The design, manufacture and installation of metal security covers, doors, grating and staging. 

Tyco Fire Products Manufacturing Limited 

Stockport Trading Estate, Yew Street, Stockport, Cheshire SK4 2JW, United Kingdom 

Tel: +44 (0)161 429 3400 • Fax: +44 (0)161 477 6729 

E-mail: tycofireproducts.uk@tyco-bspd.com • Website: www.tycobuilding.com 


Scope: 

Design and manufacture of fire protection valves, fire sprinklers, high and medium velocity nozzles and controls. 



Tel: +44 (0)1246 858100 • Fax: +44 (0)1246 857447 



Scope: 


628 20 Nov 2011


HEALTH & SAFETY CERTIFICATION BS OHSAS 18001 

HSE statistics show that some thirty million working days were lost due to work related health and safety 

issues In the UK in 2006/07. 

Poor health and safety performance not only means loss of revenue, but also loss of reputation, license to 

trade and business, and huge extra costs. In some instances it can lead to very large fines or custodial 

sentences. Good health and safety performance reduces costs and gives companies a competitive edge. 

BS OHSAS 18001 is a specification that helps to fully integrate health and safety into company policies and 

working practices. This in turn helps the company to identify risks, engage staff and continuously improve 

processes and systems. It also signals to architects, clients, insurers and specifiers that the company takes its 

health and safety responsibilities seriously. 

The assessment standard for this scheme is: 

BS OHSAS 18001:2007 Occupational health and safety management systems - Requirements. 

Argus Fire Protection Company Limited 

Hendglade House, 46 New Road, Stourbridge, West Midlands DY8 1PA, United Kingdom 

Tel: +44 (0)1384 376256 • Fax: +44 (0)1384 393955 

E-mail: info@argusfire.co.uk • Website: www.argusfire.co.uk 

Quality System Cert. No. 011-HS Assessed to OHSAS 18001:2007 

Scope: 

Design, supply and installation, servicing and maintenance of fire protection and detection systems, including site based activities. 

Kingspan Ltd 


Tel: +353 42 969 8572 • Fax: +353 42 969 8576/77 



Scope: 


purlins and accessories, gutters, flashing system and single and double translucent roof lights. 




Tel: +44 (0)1944 710591 • Fax: +44 (0)1944 710777 



Scope: 





20 Nov 2011 629


HEALTH & SAFETY CERTIFICATION BS OHSAS 18001 

Kingspan Ltd. 


Tel: +44 (0)1352 716100 • Fax: +44 (0)1352 716161 



Scope: 




Tel: +44 (0)1246 858100 • Fax: +44 (0)1246 857447 



Scope: 


630 20 Nov 2011

part 1: section 2.2 - RedBookLive

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?