Operating instructions Wire feed unit - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Machine description – quick overview Machine control – Operating elements 4.4 Machine control – Operating elements Figure 4-4 20 099-004846-EW501 8.01.2014
Machine description – quick overview Machine control – Operating elements Item Symbol Description 0 1 Lid (see chap. "Machine control – concealed operating elements") 2 Push-button, parameter selection left/power-saving mode Welding current Material thickness Wire feed speed After welding, the values used last are shown from the main program. The signal light is illuminated. Enter power-saving mode by pressing the push-button for a longer time. 3 Display, left Welding current, material thickness, wire speed, hold values 4 Welding parameter setting, rotary dial For setting the welding performance and for setting other welding parameters. 5 Select operating mode button Non-latched Latched Signal light lights up in green: Special non-latched Signal light lights up in red: MIG spot welding Special latched 6 Dynamics/choke effect button Arc harder and narrower Arc softer and wider 7 Button, Select welding type MIG/MAG standard welding MIG/MAG pulse arc welding 8 Arc length correction/selection of welding program, rotary dial • Correction of the arc length from -9.9 V to +9.9 V. • Selection of welding programs 0 to 15 (not possible if accessory components, such as program torches, are connected). 9 Display, right Welding voltage, program number 10 Button, Parameter selection (right) VOLT Welding voltage PROG Program number kW Welding performance display Gas flow quantity (optional) 099-004846-EW501 8.01.2014 21
Page 1 and 2: Operating instructions Wire feed un
Page 3 and 4: Contents Notes on the use of these
Page 5 and 6: Contents Notes on the use of these
Page 7 and 8: Safety instructions Explanation of
Page 9 and 10: Safety instructions General WARNING
Page 11 and 12: Safety instructions General CAUTION
Page 13 and 14: Safety instructions Transport and i
Page 15 and 16: Intended use Use and operation sole
Page 17 and 18: 4 Machine description - quick overv
Page 19: Machine description - quick overvie
Page 23 and 24: Machine description - quick overvie
Page 25 and 26: Design and function Installation CA
Page 27 and 28: 5.4 Notes on the installation of we
Page 29 and 30: Design and function Shielding gas s
Page 31 and 32: Design and function MIG/MAG welding
Page 53 and 54: Design and function TIG welding 5.8
Page 55 and 56: Design and function TIG welding 5.8
Page 57 and 58: Design and function TIG welding Non
Page 59 and 60: Design and function TIG welding Lat
Page 61 and 62: Design and function MMA welding 5.9
Page 63 and 64: Design and function Interfaces for
Page 65 and 66: Design and function Special paramet
Page 71 and 72:
Design and function Special paramet
Page 73 and 74:
Design and function Special paramet
Page 75 and 76:
Design and function Machine configu
Page 77 and 78:
Design and function Machine configu
Page 79 and 80:
6 Maintenance, care and disposal Ma
Page 81 and 82:
Maintenance, care and disposal Disp
Page 83 and 84:
Rectifying faults Error messages (p
Page 85 and 86:
Rectifying faults Resetting JOBs (w
Page 87 and 88:
Rectifying faults Vent coolant circ
Page 89 and 90:
Accessories General accessories 9 A
Page 91 and 92:
Replaceable parts Wire feed rollers
Page 93 and 94:
Appendix A JOB-List 099-004846-EW50
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101:
Appendix B Overview of EWM branches
show all

Operating instructions Wire feed unit - EWM Hightec Welding GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?