7 Appendix - Lehner Agrar GmbH

More documents

Recommendations

Info

4 Settings and displays 4.5 Setting cycle for electronic lifting gear control (EHR) (special equipment for headland manager) 20 If the spreader is equipped with the headland manager accessory, a specific cycle can be set for opening the slide. Press button to select the EHR cycle between 1 and 10. Press toggle switch: Setting saved, next menu item or press main switch: Setting saved and machine switched off. 4.6 Adjusting the empty indicator EHR cycle 4 Depending on the requirement and spreading material, the empty indicator can be set to respond earlier or later. The value for the empty indicator to switch on (if the spreading material falls below a certain fill level) can be adjusted from -50 to +50. Note: Depending on the spreading material or material humidity, the remainder level may vary somewhat. Press the button to set the respective value. Factory setting is 0 With + values, the empty indicator responds at a higher fill level. With - values, the empty indicator responds at a lower fill level. Setting 0 Empty ind. ON
4 Settings and displays Press toggle switch: Setting saved, next menu item or press main switch: Setting saved and machine switched off. 4.7 Displaying the spreader type The control is provided for a variety of spreaders. The VINERO ® is programmed at the factory. 4.8 Checks Press toggle switch: Setting saved, next menu item or press main switch: Setting saved and machine switched off. Spread. type 0 VINERO Voltage check In order to check the operating voltage (in V), the spreader must be on and the hopper filled. Press the button for 5 seconds. The operating voltage is displayed for 8 seconds. Voltage 14.0 V Performance check The motor is set at the factory. No changes are permitted, since otherwise the drive and control parameters no longer match. To check the performance data, the spreader must be on. 21
Page 1 and 2: LEHNER VINERO ® Operating instruct
Page 3 and 4: Table of Contents 4 Settings and di
Page 5 and 6: 1 What you should know 1.3 Intended
Page 7 and 8: 2 Starting up the VINERO ® 2.1 Mou
Page 9 and 10: 3 Operating the VINERO ® 3.1 Contr
Page 11 and 12: 3 Operating the VINERO ® 3.3 Switc
Page 13 and 14: 3 Operating the VINERO ® 3.4 Setti
Page 15 and 16: 3 Operating the VINERO ® 3.7 Perfo
Page 17 and 18: 3 Operating the VINERO ® For ferti
Page 19: 4 Settings and displays 4.3 Selecti
Page 23 and 24: 5 Special accessories 5.1 Attach st
Page 25 and 26: 5 Special accessories Sensor signal
Page 27 and 28: 7 Appendix 7.1 EU Declaration of Co
Page 29 and 30: 7 Appendix 7.3 List of spare parts
Page 31 and 32: 7 Appendix 31
Page 33 and 34: 7 Appendix 7.4 Troubleshooting Stat
Page 35 and 36: 7 Appendix White clover Stopwatch i
Page 37 and 38: 7 Appendix Fodder radish Time open:
Page 39 and 40: 7 Appendix Stopwatch is activated o
Page 41 and 42: 7 Appendix Bellmix Mulchgrass 500 T
Page 43 and 44: 7 Appendix 7.6 Slide settings Versi
Page 45: Lehner Agrar GmbH Häuslesäcker 5-

7 Appendix - Lehner Agrar GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?