zeqQT

Recommendations

Info

RIGGING HARDWARE PIGGYBACK ® SIZES: 3/8 TO 1-1/2 IN. WEDGE SOCKET CLIPS BENEFITS & FEATURES • Forged saddles include size, USA and CM logo • Drop-forged base for superior function and wearability • Galvanized finish F G E C D B A RIGGING HARDWARE Size (in.) Standard Package Product Code Saddle U-Bolt Dimensions (in.) A B C D E F G Heavy Hex Nut Galv. Torque Min. Tail Weight (ft./lbs.) (in.) (lbs.) 3/8 10 M248D 1X248 2X248L 7/16-14UNC 1.00 2.38 0.75 0.69 1.94 1.62 602224 45 6 0.8 7/16 10 M249D 1X249 2X250L 1/2-13UNC 1.19 2.62 1.00 0.66 2.31 1.78 602225 65 6 1.3 1/2 10 M250D 1X250 2X250L 1/2-13UNC 1.19 2.62 1.00 0.72 2.31 1.91 602225 65 6 1.4 9/16 10 M296D 1X296 2X251L 9/16-12UNC 1.31 3.19 1.25 0.77 2.50 1.97 602226 95 6 1.7 5/8 10 M251D 1X251 2X251L 9/16-12UNC 1.31 3.19 1.25 0.87 2.50 2.00 602226 95 6 1.7 3/4 10 M252D 1X252 2X252L 5/8-11UNC 1.50 3.50 1.50 0.91 2.81 2.34 602227 130 6 2.5 7/8 5 M253D 1X253 2X253L 3/4-10UNC 1.75 3.88 2.00 1.07 3.16 2.44 602228 225 6 3.6 1 5 M254D 1X254 2X254L 3/4-10UNC 1.88 4.25 2.00 1.22 3.47 2.62 602228 225 6 3.9 1-1/8 5 M255D 1X255 2X255L 3/4-10UNC 2.00 4.50 2.00 1.31 3.59 2.81 602228 225 6-3/4 4.9 1-1/4 5 M256D 1X256 2X256L 7/8-9UNC 2.31 5.25 2.38 1.50 4.22 3.15 602246 360 7-1/2 6.5 1-3/8 5 M257D 1X257 2X257L 7/8-9UNC 2.38 5.62 2.38 1.56 4.25 3.08 602246 360 8-1/4 7.1 1-1/2 5 M258D 1X258 2X258L 7/8-9UNC 2.59 6.00 2.38 1.75 4.47 3.41 602246 360 9 8.2 PROPER USE OF PIGGYBACK WEDGE SOCKET CLIPS • Dead end wire rope tail length should be at least 6 rope diameters, but not less than 6 inches beyond the wedge socket. See Figure 1. • Apply U-bolt and first saddle on dead end rope and the second saddle on live end rope. Install nuts. See Figures 1 & 2. • Position the dual saddle clip so that 3 to 4 inches of dead end rope remain beyond the clip. See Figures 1 & 2. • Tighten nuts evenly. Alternate tightening each nut until reaching the required torque specified. See Figure 2. • Check that clip does not pinch or clamp the live wire rope. Apply an initial test load equal to the loads expected in regular use. Be certain rope is secured properly in the wedge socket prior to any use. • Inspect for proper rope alignment with wedge socket and retighten the nuts to the specified torque. LIVE LOAD BEARING ROPE WEDGE SOCKET DEAD END ROPE CLAMPING SIDE OF CLIP TAIL LENGTH FIGURE 1 3 to 4 IN. LOOSE SIDE OF CLIP LIVE LOAD BEARING ROPE DEAD END ROPE CLAMPING SIDE OF CLIP WEDGE SOCKET FIGURE 2 TAIL LENGTH CHAIN & RIGGING ATTACHMENTS (CMRP-6) 106 PHONE: 800.888.0985 WWW.CMWORKS.COM
RIGGING HARDWARE BUNDLING CLIP SIZES: 3/4 TO 1-1/8 IN. BENEFITS & FEATURES • Galvanized and painted U-bolt with rolled threads. Interchangeable and replaceable with our standard wire rope clip U-bolts. • Forged and galvanized saddles come with FORGED USA, size, CM logo and trace code forged in. • Meets B30.26 plus traceability. • Performs to rated capacities. • After inspection, the CM B Bundling Clip is reusable. • Available for use with 3/4", 7/8", 1" and 1-1/8" wire rope chokers. A F C B E G Size (in.) Standard Package Product Code Dimensions (in.) A B C D E F G Torque (ft./lbs.) Weight (lbs.) 3/4 10 M252B 2.81 2.81 3.30 0.75 1.50 1.38 5/8"-11 UNC 130 2.5 7/8 5 M253B 3.16 2.44 3.80 0.88 1.75 1.63 3/4"-10 UNC 225 3.6 1 5 M254B 3.47 2.63 4.16 1.00 1.88 1.81 3/4"-10 UNC 225 3.9 1-1/8 5 M255B 3.60 2.81 4.54 1.13 2.00 2.00 3/4"-10 UNC 225 4.9 SEE BUNDLING CLIPS IN ACTION http://www.youtube.com/user/ColumbusMcKinnon SWAGE SOCKET (OPEN) SIZES: 1/4 TO 1-3/4 IN. BENEFITS & FEATURES • Forged from fine grain, special bar quality C-1035 steel • Spheroidized annealed for cold swaging • Recommended for use on 6" x 19" or 6" x 37" IWRC regular lay wore ropes. Can also be used on galvanized bridge rope. • Not for use on fiber core or lang lay ropes. • Sockets have 100% efficiency rating based on catalog strength of wire rope when properly applied A H L F E O M B D Y RIGGING HERC-ALLOY HARDWARE ® 800 Size (in.) Product Code Dimensions (in.) A B D E F H L M O Y After Swage Diameter (in.) 1/4 697120 0.50 0.27 0.69 1-1/2 4-3/4 2-1/8 4 5/16 11/16 1-3/8 0.44 0.55 3/8 697122 0.77 0.41 0.81 1-3/4 6-1/4 3-3/16 5-5/16 13/32 13/16 1-5/8 0.69 1.08 7/16 697123 0.98 0.48 1.00 2 7-13/16 4-1/4 6-11/16 1/2 1 2 0.88 2.30 1/2 697124 0.98 0.55 1.00 2 7-13/16 4-1/4 6-11/16 1/2 1 2 0.88 2.25 9/16 697125 1.26 0.61 1.19 2-1/4 9-9/16 5-5/16 8-1/8 5/8 1-1/4 2-1/2 1.13 4.60 5/8 697126 1.26 0.67 1.19 2-1/4 9-9/16 5-5/16 8-1/8 5/8 1-1/4 2-1/2 1.13 4.50 3/4 697127 1.55 0.80 1.38 2-3/4 11-11/16 6-3/8 10 3/4 1-1/2 3 1.38 7.80 7/8 697128 1.70 0.94 1.63 3-1/4 13-5/8 7-7/16 11-5/8 15/16 1-3/4 3-3/8 1.50 11.70 1 697129 1.98 1.06 2.00 3-3/4 15-5/8 8-1/2 13-3/8 1-1/32 2 4 1.75 17.80 1-1/8 697130 2.25 1.19 2.25 4-1/4 17-1/2 9-9/16 15 1-3/16 2-1/4 4-1/2 2.00 29.70 1-1/4 697131 2.53 1.33 2.50 4-3/4 19-7/16 10-5/8 16-1/2 1-3/16 2-1/2 5 2.25 36.00 1-3/8 697132 2.80 1.45 2.50 5-1/4 21-1/4 11-11/16 18-1/8 1-5/16 2-1/2 5-1/4 2.50 47.00 1-3/4 697134 3.39 1.86 3.50 6-3/4 27-1/8 14-7/8 23 1-11/16 3-1/2 7 3.00 93.00 Weight (lbs.) WWW.CMWORKS.COM CHAIN & RIGGING ATTACHMENTS (CMRP-6) PHONE: 800.888.0985 107
Page 1 and 2:
CHAIN & RIGGING ATTACHMENTS SHACKLE
Page 3 and 4:
TABLE OF CONTENTS PRODUCT OVERVIEW
Page 6 and 7:
BUY WITH CONFIDENCE CM is Proud to
Page 9 and 10:
PRODUCT OVERVIEW From CM Chain and
Page 11 and 12:
DIMENSIONS, WEIGHTS & WLL Chain Siz
Page 13 and 14:
STANDARD TYPES OF CM CHAIN SLINGS S
Page 15 and 16:
NON-OVERHEAD LIFTING HOOKS Non-over
Page 17 and 18:
PRODUCT OVERVIEW NON-OVERHEAD LIFTI
Page 19 and 20:
WIRE ROPE ATTACHMENTS OVERVIEW Wire
Page 21 and 22:
BINDER CHAIN ASSEMBLIES Binder Chai
Page 23 and 24:
CHAIN & SLING INSPECTION, USE & CAR
Page 25 and 26:
CHAIN & SLING INSPECTION, USE & CAR
Page 27 and 28:
transverse nick in an area of high
Page 29 and 30:
CHAIN SELECTION & WORKING LOAD LIMI
Page 31 and 32:
SINGLE LEG (VERTICAL) SINGLE LEG (C
Page 33 and 34:
VISIT OUR BLOG AT BLOG.CMWORKS.COM
Page 35 and 36:
Horizontal Angle 3-LEG BRIDLE 6X19
Page 37 and 38:
SYNTHETIC ROUNDSLING WORKING LOAD L
Page 39:
CMCO UNIVERSITY CMCO University is
Page 42 and 43:
RIGG ING & ATTACH CHME MENT NTS SHA
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 57 and 58: CHAIN SLINGS & COMPONENTS RATED FOR
Page 59 and 60: CHAIN SLINGS & COMPONENTS CHAIN SLI
Page 61 and 62: CHAIN SLINGS & COMPONENTS HERC-ALLO
Page 63 and 64: RI GGIN ING & ATTACHMENTS CHAIN SLI
Page 73 and 74: CHAIN SLINGS & COMPONENTS HERC-ALLO
Page 83: RI GGIN ING & ATTACHMENTS CHAIN SLI
Page 86 and 87: RIGGING HARDWARE RIGGING HARDWARE O
Page 88 and 89: RIGGING HARDWARE SORTING HOOK HERC-
Page 90 and 91: RIGGING HARDWARE RIGGING HOOK WORKI
Page 92 and 93: RIGGING HARDWARE REPLACEMENT HOOK W
Page 94 and 95: RIGGING HARDWARE MASTER LINK WITH &
Page 96 and 97: RIGGING HARDWARE SHOULDER EYE BOLTS
Page 98 and 99: 5,000 LBS. RIGGING HARDWARE HOIST R
Page 100 and 101: RIGGING HARDWARE SPECIALTY ENGINEER
Page 102 and 103: RIGGING HARDWARE HOIST RING SWIVEL
Page 104 and 105: RIGGING HARDWARE WIRE ROPE CLIPS SI
Page 108 and 109: RIGGING HARDWARE SWAGE SOCKET (CLOS
Page 111 and 112: BELOW-THE- HOOK ATTACHMENTS CAMLOK
Page 113 and 114: RI GGIN ING & ATTACHMENTS BELOW-THE
Page 129: RI GGIN ING & ATTACHMENTS BELOW-THE
Page 132 and 133: RIGG ING & ATTACH CHME MENT NTS TRA
Page 156 and 157:
RIGG ING & ATTACH CHME MENT NTS TRA
Page 159 and 160:
SPECIALTY CHAIN & COMPONENTS Winch
Page 161 and 162:
RI GGIN ING & ATTACHMENTS SPECIALTY
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
ENTERTAINMENT RIGGING PRODUCTS ENTE
Page 169:
RIGGING & ATTACHMENTS ENTERTAINMENT
Page 172 and 173:
ELECTRIC HOISTS MODEL COMPARISON SH
Page 175 and 176:
AIR HOISTS MODEL COMPARISON SHOPAIR
Page 177 and 178:
MODEL COMPARISON PA RATCHET LEVER H
Page 179 and 180:
MODEL COMPARISON HURRICANE 360° HA
Page 181 and 182:
BANDIT TM RATCHET LEVER HOIST SUGGE
Page 183 and 184:
BANDIT TM RATCHET LEVER HOIST HOIST
Page 185 and 186:
HURRICANE 360° TM HAND CHAIN HOIST
Page 187 and 188:
BEAM CLAMP BEAM CLAMP Ideal as an a
Page 189 and 190:
Twin Beam Clamps enable one beam to
Page 191 and 192:
OVERHEAD LIFTING The process of lif
Page 193 and 194:
INDEX (BY PRODUCT NAME) PRODUCT NAM
Page 195 and 196:
INDEX (BY SECTION) PRODUCT NAME PAG
Page 197 and 198:
INDEX (BY PRODUCT CODE) PRODUCT COD
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
WWW.CMWORKS.COM CHAIN & RIGGING ATT
show all

zeqQT

Create successful ePaper yourself

Delete template?

Save as template?