RA Replacing front left wheel arch (Z3) - Ad Kusters
RA Replacing front left wheel arch (Z3) - Ad Kusters
RA Replacing front left wheel arch (Z3) - Ad Kusters
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
41 14 020 <strong>Replacing</strong> <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong> (<strong>Z3</strong>)<br />
Instructions on body repair,<br />
refer to 41 00<br />
Place vehicle on straightening bench.<br />
<strong>Z3</strong><br />
Spare part for <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong><br />
Remove or disconnect following parts:<br />
- Complete <strong>front</strong> bumper<br />
- Front wall<br />
- Side panel<br />
- Front axle with engine and transmission<br />
- Both headlights complete<br />
- Brake booster<br />
- Mounting block for pedals<br />
- Front <strong>wheel</strong> <strong>arch</strong> trim<br />
- Complete servo unit<br />
Other vehicle parts located in the repair zone or subject to<br />
damage from heat, sparks or dust, must be removed or<br />
covered.<br />
<strong>RA</strong> <strong>Replacing</strong> <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong> (<strong>Z3</strong>) BMW AG - TIS 21.01.2004 00:40<br />
Issue status (10/2001) Valid only until next CD is issued Copyright Page - 1 -
Expose connection for <strong>front</strong> <strong>wheel</strong> <strong>arch</strong> on carrier support and<br />
cut.<br />
Expose connection for outer <strong>wheel</strong> <strong>arch</strong> and drill out welding<br />
points.<br />
Expose connection for <strong>wheel</strong> <strong>arch</strong>/engine support and drill out<br />
welding points.<br />
Expose connection for spring strut shock absorber on engine<br />
support and cut connection point.<br />
Remove <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong>.<br />
<strong>RA</strong> <strong>Replacing</strong> <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong> (<strong>Z3</strong>) BMW AG - TIS 21.01.2004 00:40<br />
Issue status (10/2001) Valid only until next CD is issued Copyright Page - 2 -
Remove scrap metal.<br />
Straighten and grind joint surfaces.<br />
Note:<br />
To facilitate installation, bend closing plate up a little.<br />
Clean connection points on vehicle and coat with zinc dust<br />
paint.<br />
Coat connection points on spare part for <strong>wheel</strong> <strong>arch</strong> with zinc<br />
dust paint.<br />
<strong>Ad</strong>just spare part for <strong>wheel</strong> <strong>arch</strong> to fit with straightening angle<br />
set.<br />
Weld connection for <strong>front</strong> <strong>wheel</strong> <strong>arch</strong> to carrier support.<br />
<strong>RA</strong> <strong>Replacing</strong> <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong> (<strong>Z3</strong>) BMW AG - TIS 21.01.2004 00:40<br />
Issue status (10/2001) Valid only until next CD is issued Copyright Page - 3 -
Weld outer <strong>wheel</strong> <strong>arch</strong> connection.<br />
Weld connection between <strong>wheel</strong> <strong>arch</strong>/engine support.<br />
Weld connection on spring strut shock absorber to engine<br />
support.<br />
Grind down connection points and seal.<br />
<strong>RA</strong> <strong>Replacing</strong> <strong>front</strong> <strong>left</strong> <strong>wheel</strong> <strong>arch</strong> (<strong>Z3</strong>) BMW AG - TIS 21.01.2004 00:40<br />
Issue status (10/2001) Valid only until next CD is issued Copyright Page - 4 -
Change language