QuietShield-Engine-Silencer-Catalog-Cylindrical-6-28 ... - Universal

Silencers - Cylindrical
Type 3, Side-in, End-out
Commercial Grade
15–25 dB(A)
Type 3: Side-in, End-out
A
Inlet Size
Pressure Drop (inches of water)
24.0
20.0
16.0
12.0
8.0
4.0
0
0
Connection
Type
Type 3
Part Number
2,000 4,000 6,000 8,000 10,000 12,000 14,000
Silencer Outlet Velocity (ft/min)
B
Silencer
Diameter
C
Body Length
Attenuation (dB)
D
Type 3
Overall Length
50
45
40
35
30
25
20
15
10
5
0
E
Inlet/Outlet
Length
“F” 125/150# ANSI Mounting Flange:
Bore sizes 4" and above.
“C” Inlets and Outlets
Bore sizes < 4".
F
Type 3
Inlet Offset
2 Cuff 63202C 5 12.5 14.5 2 3 8
2 NPT 63202P 5 12.5 14.5 2 3 8
2.5 Cuff 63225C 6 15 18 3 4 14
2.5 NPT 63225P 6 15 18 3 4 14
3 Cuff 63203C 8 20 23 3 5 20
3 NPT 63203P 8 20 23 3 5 20
3.5 Cuff 63235C 8 20 23 3 5 25
3.5 NPT 63235P 8 20 23 3 5 25
4 Flange 63204F 10 25 28 3 6 40
5 Flange 63205F 12 30 34 4 7 55
6 Flange 63206F 14 35 39 4 8 75
8 Flange 63208F 18 45 49 4 10 130
10 Flange 63210F 22 55 59 4 12 235
12 Flange 63212F 26 65 69 4 14 335
14 Flange 63214F 30 75 79 4 15 445
16 Flange 63216F 36 90 94 4 20 660
18 Flange 63218F 42 105 109 4 22 1000
20 Flange 63220F 42 105 109 4 24 1050
22 Flange 63222F 48 120 124 4 26 1350
Silencer Standards
Mild steel construction – Max temp 1,000°F;
primary use; 1,250°F intermittent use
2"–3.5" inlet sizes – ID tube or NPT
4" plus inlet sizes – ANSI hole spacing 125/150#
Silver, high heat paint
Silencer Options
Mounting brackets, gussets and lifting lugs
Custom inlet and outlet locations and extensions
available
304, 316 or 316L stainless steel construction
Thermal insulation blankets
24" and above inlet sizes available
as custom order
Black, high heat paint
“P” Male Pipe Ends:
Bore sizes < 4".
Commercial Grade Typical Attenuation Curve
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
Actual performance data may vary.
Type 3
Weight
All dimensions are in inches unless otherwise stated.
All weights are in pounds and are approximate.
WARNING: Silencers should not be installed near fuel lines, fuel tanks,
combustible material, wiring, fire suppression systems, etc. Area around exhaust
system should be clearly marked per OSHA standards.
All information correct at time of printing. Universal has a policy of continuous
improvement. Therefore we reserve the right to change the specifications of these
silencers without notice.
7
Need something similar with slight modifications?
Mark up the outline drawing above and fax to (608) 873-7298 or
scan and email to info@universalAET.com
94-1648