Bucket Elevators - Technical Expressions

More documents

Recommendations

Info

SPECIFICATION POTASH: COMPACTOR EXPANSION SECTION: 41 12 16 BUCKET ELEVATORS EQUIPMENT SPECIFICATION ENQUIRY NUMBER: REV. A, PAGE: 8 OF 10 10. SURFACE TREATMENT AND RUST PROTECTION 10.1 Painting 10.1.1 Surface preparation and painting for fabricated steel components, including structural elements and plate work, shall be as defined in the standard specification Section S01 80 15.23, Coating Systems For Steel. 10.1.2 The following shall not be painted: • Underside of base plates supported on concrete foundations • Stud welded shear connectors • Stainless steel and other corrosion-resistant materials • Machined surfaces 10.2 Rust Protection 10.2.1 Prior to shipment, bearings, drive parts, operating linkages, etc., shall be covered with a rust preventative oil or grease and wrapped with suitable paper to prevent entrance of moisture. 11. SHOP ASSEMBLY, INSPECTION, AND TESTING 11.1 General 11.1.1 The equipment shall be shop assembled prior to shipment. All critical dimensions shall be verified and all motions checked and tested. 11.1.2 The Vendor shall advise procedures and testing programs to be followed to guarantee soundness and integrity of the equipment. 11.1.3 The Vendor shall institute and conduct a quality system in accordance with Level B of Section S01 43 00, Quality Assurance and Surveillance. 11.1.4 The approval or review comments of any work by the Owner/Engineer and its release shall not relieve the Vendor of any responsibility for carrying out the provisions of this specification. 11.2 Inspection and Testing 11.2.1 The Owner reserves the right to inspect the components at any time during manufacturing to assure that the materials and the workmanship are in accordance with this specification. The Owner’s representative shall have PTMFOG0000000184.Doc ©Hatch 2004/12
SPECIFICATION POTASH: COMPACTOR EXPANSION SECTION: 41 12 16 BUCKET ELEVATORS EQUIPMENT SPECIFICATION ENQUIRY NUMBER: REV. A, PAGE: 9 OF 10 reasonable access to the Vendor’s manufacturing and assembly facilities during the execution of the work. 11.2.2 Each unit shall be mechanically tested in the Vendor’s premises using the Vendor’s standard quality control and testing procedures to ensure delivery of a high quality product suitable for the intended application. 11.2.3 All tests are subject to witnessing by the Owner. 11.2.4 The Owner may inspect the equipment at various stages of fabrication, and should be notified 21 calendar days in advance, unless otherwise specified, for his representative to be present for the following milestones: • Final assembly and mechanical run test. • Preparation for shipping. 11.2.5 The Vendor shall certify the tests were performed. 12. PREPARATION FOR SHIPMENT 12.1 Refer to General Packing Instructions for details. 13. DOCUMENTATION 13.1 Issuance of Documents 13.1.1 The Vendor shall submit drawings and information as specified in Section 01 32 19, Vendor Data Requirements. 13.1.2 Vendor shall submit completed datasheets with bid. 13.1.3 Vendor shall submit a detailed quality control procedure for review by the Owner/Engineer prior to commencing fabrication. 13.1.4 The Vendor shall submit detailed fabrication drawings for review prior to fabrication. This review shall cover compliance with the applicable code requirements and regulation, general design and dimensions, and shall not relieve the Vendor from providing documents with accurate design information. 13.2 Document Review 13.2.1 The Vendor’s welding procedure and qualification records shall be submitted for approval upon receipt of purchase order. PTMFOG0000000184.Doc ©Hatch 2004/12
Page 1 and 2: SPECIFICATION POTASH: COMPACTOR EXP
Page 7: SPECIFICATION POTASH: COMPACTOR EXP

Bucket Elevators - Technical Expressions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?