Reference Standards Calibration Blocks - PH Tool

Recommendations

Info

ULTRASONIC TESTING WEDGES Circumferential Shear Wave Wedges This custom machined wedge (shoe) is used for shear wave testing in round or tubular products. The radius is machined to precisely match the material being tested. The refracted angle is adjusted by positioning the search unit along the wedge. Wedge is machined from plexiglass and the sliding clamp is aluminum. Includes knurled brass set screws. Customer specifies radius. Longitudinal Wave Wedges This custom machined wedge is used for longitudinal wave propagation in testing in round or tubular products. The radius is machined to precisely match the material being tested. Wedge is machined from plexiglass and the sliding clamp is aluminum. Includes knurled brass set screws. Customer specifies radius. This wedge is not pictured. Custom-machining of supplied wedges PH Tool offers fast turnaround on the custom machining of radius (circumferential or longitudinal) of customer-supplied wedges. Customer specifies radius. NON-METALLIC ULTRASONIC STANDARDS Non-metallic Ultrasonic Standards Standards can be made in non-metals too. We make specials in polyethylene, plexiglass, ABS and other plastics, composites, as well as some ceramics. While these materials cannot be machined by the EDM process, we can make FBHs, narrow notches, and other machined reflectors and shapes. Call Technical Sales to discuss your non-metallic standards requirements. TECH SCALES Tech Scales (Pack of 5) You’ve seen them at our booth at trade shows over the years, now our handy NDT Technician scales are available for sale in packages of five scales. Made of sturdy, anodized aluminum, these great little scales are Inch on one side (0 to 8 inch in increments of .050, and .100), and Metric on the other (0 to 200 mm in 1 mm increments.) www.phtool.com email: sales@phtool.com 4406 Bethlehem Pike, Telford, PA 18969 USA Tel: 267-203-1600 Fax: 267-203-1601 16
.62 5 17 EDDY CURRENT CALIBRATION STANDARDS A B C D E F G 0" 2" 4" 6" 7" 8" 11" 12" 13" .353" SER NO. .625 .500" 0.00 2” typ 1.2" TYP A B C D 0” 3” 5” 7” 9” 12” .035 WALL .049 WALL 1 2 3 2.00 4.00 6.00 A 12” 14" 4 B C www.phtool.com email: sales@phtool.com 5 6 8.00 10.00 12.00 D SER. NO. 12" 1 2 3 4 5 6 7 8 9 14.00 ASME Sec. V Calibration Reference Standard 2007 Code This standard is used to establish and verify system response for ET examination of nonferromagnetic steam generator heat exchanger tubing. Manufactured from tubing of the same nominal size and material type as that being examined. Discontinuities include one (1) through-wall hole (0.052” dia for tubing 3/4” and under; 0.067” dia for over 3/4”); four (4) through-wall holes @ .026” dia (for tubing 3/4” and under) or .033” dia (for tubing over 3/4”) indexed 90°; one (1) 7/64” FBH @ 60%; and four (4) 3/16” FBHs @ 20% indexed 90°. Tubing can be customer or PH Tool-supplied. In accordance with 2007 ASME Section V, Article 8, Appendix II, Paragraph II-860.2. ASME Sec. V Calibration Reference Standard Pre - 2007 Code This standard is used to establish and verify system response for ET examination of nonferromagnetic steam generator heat exchanger tubing. Manufactured from tubing of the same nominal size and material type as that being examined. Discontinuities include one (1) through-wall hole (0.052” dia for tubing 3/4” and under; 0.067” dia for over 3/4”); one (1) 5/64” dia FBH @ 80% deep; one (1) 7/64” FBH @ 60%; one (1) 3/16” FBH @ 40%; four (4) 3/16” FBHs @ 20% indexed 90°; one (1) 1/8” wide 360° OD groove at 20% deep; and one (1) 1/16” wide 360° ID groove @ 10%. Tubing can be customer or PH Tool-supplied. In accordance with ASME Section V, Article 8, Appendix I, Paragraph I-865. .020 SER NO. ID FBH Calibration Standard Custom standard containing five (5) 0.010” diameter FBHs at varying depths from 0.002” to 0.006”, and one (1) 0.010” diameter through-wall hole. FBH depth and location can be customer-directed. Typical separation between holes is 2”. 180° 3-Flaw Wearscar Standard Popular standard containing three (3) wearscars at 180° circumferential extent at depths (wall loss) of 25%, 50%, and 75% of wall thickness. 20%, 40%, 60% also popular. Extent of wearscar can be other than 180° if preferred. Standard also contains one (1) through-wall hole (0.052” dia. for tubing 3/4” and under; 0.067” dia. for tubing over 3/4”. Circ extents of 120° and 360° also available. .042" Circ Notch Eddy Current Standard This standard contains nine (9) circumferentially-oriented OD EDM notches. All notches are 20% TWD (through-wall depth). Circumferential extent is 10° through 90° in 10° increments. Notch width is normally 0.005” to 0.010”. Other variations are available. 4406 Bethlehem Pike, Telford, PA 18969 USA Tel: 267-203-1600 Fax: 267-203-1601
Page 1 and 2: ��
Page 3 and 4: Contents EDM Notch Information Shee
Page 5 and 6: Ultrasonic Reference Standards (Oth
Page 7 and 8: EDM N O T C H E S Since 1973…. PH
Page 9 and 10: WHAT IS EDM? Electrical Discharge M
Page 11 and 12: ULTRASONIC TEST BLOCKS IIW-Type 1 B
Page 13 and 14: ULTRASONIC TEST BLOCKS Miniature Re
Page 15 and 16: ULTRASONIC TEST BLOCKS Sizing Block
Page 17 and 18: 9 MIL-STD-2154 Ultrasonic Test Bloc
Page 19 and 20: ULTRASONIC CALIBRATION BLOCKS/STAND
Page 21 and 22: .250 .500" 13 .250 ULTRASONIC REFER
Page 23: 15 ULTRASONIC REFERENCE STANDARDS (
Page 27 and 28: EDDY CURRENT CALIBRATION STANDARDS
Page 29 and 30: 21 12 3/8 6 C L NOTCH #1 5 NOTCH #2
Page 31 and 32: 23 www.phtool.com email: sales@phto
Page 33 and 34: SERVICES AVAILABLE Surface Grinding
Page 35 and 36: To: PH TOOL SALES DEPT. Fax: 267-20
Page 37 and 38: ULTRASONIC TEST BLOCK PRICE LIST PH
Page 43 and 44: DIMENSIONAL INSPECTION PRICE LIST P
Page 45: ��

Reference Standards Calibration Blocks - PH Tool

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?