catalog

MM HT
d1
a° TS
Dh9
• Ground, neutrally inclined rake face.
• The tapered contour enables
machining of 90° high walls.
• May be used for machining
hardened steel.
R
Ap
L
ECONOMICAL
SOLUTIONS
MM HT 2 Flute Toroidal Head
Designation D Z Ap Ts d1 L α° R
Specially Tailored (1)
Radius Range IC908 IC903
MM HT100C08R0.5-2T06 10.0 2 7.0 T06 9.6 12.4 5 0.5 R0.0÷R1.0 •
MM HT100N07R0.5-2T06 10.0 2 7.0 T06 9.6 11.2 5 0.5 R0.0÷R1.0 •
MM HT100C08R1.0-2T06 10.0 2 7.0 T06 9.6 12.4 5 1.0 R0.0÷R1.0 •
MM HT100N07R1.0-2T06 10.0 2 7.0 T06 9.6 11.2 5 1.0 R0.0÷R1.0 •
MM HT100N06R2.0-2T06 10.0 2 6.0 T06 9.6 12.6 7 2.0 R0.0÷R3.0 •
MM HT100N07R2.0-2T06 10.0 2 7.0 T06 9.6 11.2 5 2.0 R0.0÷R3.0 •
MM HT100N07R3.0-2T06 10.0 2 7.0 T06 9.6 11.2 5 3.0 R2.7÷R4.0 •
MM HT120N06R3.0-2T06 12.0 2 5.7 T06 9.6 9.1 7 3.0 R2.7÷R4.0 •
MM HT120N06R4.0-2T06 12.0 2 5.4 T06 9.6 9.1 7 4.0 R2.7÷R4.0 •
MM HT120N06R1.6-2T08 12.0 2 6.3 T08 11.5 11.1 7 1.6 R1.3÷R2.7 • •
MM HT120N06R2.0-2T08 12.0 2 6.2 T08 11.5 11.1 7 2.0 R1.3÷R2.7 • •
MM HT120N06R2.5-2T08 12.0 2 6.1 T08 11.5 11.1 7 2.5 R1.3÷R2.7 •
MM HT120N06R3.0-2T08 12.0 2 6.1 T08 11.5 11.1 7 3.0 R2.7÷R4.4 • •
MM HT120N06R4.0-2T08 12.0 2 5.9 T08 11.5 11.1 7 4.0 R2.7÷R4.4 •
MM HT160N08R5.0-2T10 16.0 2 8.0 T10 15.2 20.2 7 5.0 R2.7÷R4.4 • •
MM HT200N11R3.0-2T12 20.0 2 11.1 T12 18.3 17.0 7 3.0 R3.0÷R8.0 •
MM HT200N11R4.0-2T12 20.0 2 11.5 T12 18.3 17.4 7 4.0 R3.0÷R8.0 •
MM HT200N11R5.0-2T12 20.0 2 11.5 T12 18.3 17.4 7 5.0 R3.0÷R8.0 •
MM HT200N11R6.0-2T12 20.0 2 11.4 T12 18.3 17.4 7 6.0 R3.0÷R8.0 •
MM HT200N11R8.0-2T12 20.0 2 11.3 T12 18.3 17.4 7 8.0 R3.0÷R8.0 •
(1)
Available upon request
Clamping key should be ordered separately
Do not apply lubricant to the threaded connection
P Steel 4 4
M Stainless Steel 4 4
K Cast Iron 4
S High Temp. Alloy 4 4
H Hardened Steel 4 4
Delivering
Profitability
I S C A R G u a r a n t e e s R e s u l t s
230