IRATHANE SA-10 THANE SA-10 PRIMER - Devcon
IRATHANE SA-10 THANE SA-10 PRIMER - Devcon
IRATHANE SA-10 THANE SA-10 PRIMER - Devcon
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>IRA<strong>THANE</strong></strong> <strong>SA</strong>-<strong>10</strong><br />
<strong>PRIMER</strong><br />
PRODUCT DATA BULLETIN<br />
<strong>IRA<strong>THANE</strong></strong> <strong>SA</strong>-<strong>10</strong> <strong>PRIMER</strong> is a single component ambient temperature curing high strength adhesive for bonding<br />
polyurethane coatings and liquid linings to properly prepared metal substrates. The <strong>SA</strong>-<strong>10</strong> Primer is designed for spray<br />
or roller applications.<br />
PRODUCT DATA<br />
Typical Liquid Properties:<br />
Percent solids (by weight)...............................................................................................................................6.2%<br />
Viscosity, brookfield @ 75°F.........................................................................................................................28 cps<br />
Weight per gallon.........................................................................................................................................7.0 lbs<br />
Flashpoint......................................................................................................................................................60°F<br />
Color....................................................................................................................................Light amber/Light blue<br />
SURFACE PREPARA<br />
ARATION<br />
It is important that all surfaces to be coated be free of all contamination and previous coatings. Refer to “Surface<br />
Preparation” data bulletin for complete instructions.<br />
APPLICATION<br />
Brush, roller, air spray or airless spray equipment may all be used to successfully apply <strong>SA</strong>-<strong>10</strong> Primer.<br />
Material must be applied as is, do not thin. Apply Irathane <strong>SA</strong>-<strong>10</strong> Primer at approximately 4 mils wet gauge per coat.<br />
COVERAGE<br />
The coverage rate for <strong>SA</strong>-<strong>10</strong> Primer is 250 sq.ft. per gallon per coat. To provide acceptable adhesion (exceeding the<br />
cohesive strength of the Irathane) in wear or chemical applications, 2 coats of <strong>SA</strong>-<strong>10</strong> followed by 1 coat of UU-56 adhesive<br />
are required.<br />
DRYING TIME<br />
All freshly blasted metal surfaces should be protected with 1 coat of <strong>SA</strong>-<strong>10</strong> Primer applied within 8 hours after blasting to<br />
prevent rusting of the newly exposed surface. The drying time for this primer is 15 minutes minimum and 1 month<br />
maximum between coats. The final coat must be dry for a minimum of 30 minutes and must be followed by the application<br />
of the UU-56 adhesive within 72 hours.<br />
NOTE: One additional coat of <strong>SA</strong>-<strong>10</strong>, either brushed or sprayed, is sufficient to freshen a fully primed surface which has<br />
received more than 72 hours exposure.<br />
CLEAN-UP. Both acetone and MEK solvents serve as excellent cleaners for equipment.<br />
Caution: These solvents are highly flammable and must be protected from sparks and open flames. Note: Solvent<br />
cleaning MUST precede the introduction of Irathane coating into spray equipment which has been used to apply <strong>SA</strong>-Series<br />
primers.<br />
SHELF LIFE. When stored in its original unopened container at 70°F shelf life for the <strong>SA</strong>-<strong>10</strong> primer is guaranteed for a<br />
period of 1 year. Long-term storage temperature should not exceed 80°F.<br />
ITW <strong>Devcon</strong>, 30 Endicott St., Danvers, MA 01923
PRECAUTION<br />
The primer solvent systems is flammable and must be protected from open flames and sparks. Avoid prolonged breathing<br />
of vapor and contact with skin. These primers should be applied in well-ventilated areas.<br />
For complete safety and handling information, please refer to the appropriate Material Safety Data Sheets PRIOR to using<br />
this product.<br />
For technical assistance, please call 1-800=933-8266.<br />
ORDERING INFORMATION<br />
Stock No. Unit Size<br />
94211 1 gallon<br />
942<strong>10</strong> 5 gallon<br />
NON-WARRANTY: Because we cannot anticipate the conditions under which this information or our products may be used, we<br />
can accept no liability for the results obtained. The information in this bulletin should not go construed as an expressed or implied<br />
warranty of merchantability or fitness for a particular purpose. We suggest that potential users conduct their own tests to determine the<br />
suitability of this product for a particular purpose.<br />
9/12/96