Submersible Pond Pump 4000 - Bermuda

▼ LIMITED WARRANTY
This product is guaranteed for a period of 3 years from the date of purchase
for material or manufacturing defects, with the exception of the impellor and
shaft which carries a 1 year guarantee. The guarantee covers the
substitution of defective parts. However, the guarantee is considered void in
the case of improper use, improper handling or negligence on the part of the
buyer. If your pump fails please return it to the retail outlet where you
purchased the product. Please note, you must take your proof of purchase
with you.
▼ SPARES
Replacement impellors and shafts and other components are available.
Please contact our Customer Services Department on 01905 798666 quoting
code BER0163 for replacement impellors and shafts.
BERMUDA 4000
SUBMERSIBLE PUMP
BER0255
OWNER’S MANUAL
▼ INTRODUCTION
BERMUDA pumps are carefully inspected and tested to ensure both safety
and operating performance. However, failure to follow the instructions and
warnings in the manual may result in pump damage and/or serious injury. Be
sure to read and save this manual for future reference.
EXCLUSIVELY DISTRIBUTED BY:
Solus Garden & Leisure Limited
Berry Hill Industrial Estate
Droitwich
Worcestershire WR9 9AB
Tel: 01905 798666
JET SET ASSEMBLY
NOTE: Not all models have all
the accessories
Find us on Facebook @
Bermuda Water Gardening

▼ PERFORMANCE
A clogged or dirty intake grill will greatly reduce performance. If the pump is
used in dirty water, raise it slightly to reduce the amount of debris contacting
the intake.
On initial installation, there may be air in the pump and tubing. To disperse
the air pocket, turn on and off several times.
N
E
L
IMPORTANT
The wires in the mains lead are
coloured in accordance with the
following code:
Green-and-yellow: Earth (E)
Blue: Neutral (N)
Brown: Live (L)
▼ MAINTENANCE
NOTE: Before starting any maintenance, always disconnect from the
electrical supply.
To clean the pump, remove the front cover and the impeller. Use a small
brush or stream of water to remove any debris.
Caution: If the pump fails to operate, check the following:-
• Check the circuit breaker to ensure the pump is getting electrical power.
• Check the pump discharge and tubing for kinks and obstructions. Algae
build up can be flushed out with a garden hose.
• Check the inlet grill to ensure it is not clogged with debris.
• Remove the pump inlet to access the impeller area. Turn the rotor to
ensure it is not broken or jammed.
• Monthly maintenance will add to your pump’s life.
NOTE: Ensure that the electrical cord loops below the electrical outlet
to form a ‘Drip Loop’. This will prevent water from running down the
cord into the electrical outlet.
YOU MUST ALWAYS CONSULT A QUALIFIED ELECTRICIAN
OR LOCAL ELECTRICITY AUTHORITY IF YOU HAVE
ANY DOUBTS ABOUT WIRING TO THE MAINS SUPPLY.
WARNING: This appliance must be earthed and it is essential that all
connections are securely made using the following code.
This product is designed to be permanently wired to a mains supply.
The wire which is coloured green-and-yellow must be connected to the
terminal which is marked with letter E, the earth symbol, or coloured green or
green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which
is marked with the letter L or coloured red.
▼ WARNING: SAFETY AND ELECTRICAL CONNECTIONS
1. The pump is supplied complete with 10M of 3-core electrical cable, which
is permanently connected and sealed to the motor. The supply cable of
this pump cannot be replaced; if the cable is damaged, the pump should
be discarded. The installation must conform to the regulations of the local
electrical authority.
2. A 10MA or 30MA residual current device (RCD) must be fitted to the
mains supply.
3. If an extension cable is required, this should be connected to the end of
the pump cable using a weatherproof cable connector. The joint must be
positioned outside the water in a suitable dry housing. The extension
cable should be of 3-core, 0.75mm² PVC insulated cable (ref HO3VVF)
and permanently wired to the mains supply with a 3 AMP fuse.
4. The pump cable (and extension cable) should be adequately protected
from damage.
IMPORTANT – WARNING
Always disconnect all appliances in the display from the electrical
supply before putting your hands in the water whilst the equipment is
being installed, repaired, maintained or handled. If the supply cable is
damaged it cannot be replaced and the appliance should be destroyed.
• Do not use the supply cable to lift the pump as this may cause damage.
We recommend fitting a lifting cord when the pump is installed in deep
water.
• Do not operate or leave the pump in freezing conditions.
• Do not allow the pump to run dry.
• Check that the voltage marked on the pump corresponds to the mains
supply.
• Do not pump flammable liquids.
• Operate in fresh water only.
• Only operate the pump when it is fully submerged.