Pozzi_Ortho_Resin_Li.. - American Tooth Industries
Pozzi_Ortho_Resin_Li.. - American Tooth Industries
Pozzi_Ortho_Resin_Li.. - American Tooth Industries
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
V - REACTIVITY INFORMATION<br />
STABILITY<br />
CONDITIONS TO AVOID<br />
__X__ STABLE ____ UNSTABLE<br />
Heat, Aging, Contamination, Oxygen-Free atmosphere<br />
HAZARDOUS DECOMPOSITION PRODUCTS<br />
N/A<br />
HAZARDOUS POLYMERIZATION<br />
CONDITIONS TO AVOID<br />
__X__ MAY OCCUR ____ WILL NOT OCCUR Heat, Oxygen-Free atmosphere and sunlight<br />
INCOMPATIBILITY (MATERIALS TO AVOID)<br />
____ WATER __XX__ OTHER<br />
Other Oxidizing or reducing agents, acids and bases, UV light, contamination<br />
VI - SPILL OR LEAK PROCEDURE<br />
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED<br />
Keep spectators away. Eliminate ignition sources. Use self-contained breathing apparatus (pressure- demand, MSHA/NIOSH approved),<br />
impervious clothing and boots. Dike and contain spill with inert material (e.g. sand, earth). Transfer liquid to containers for recovery or disposal<br />
and solid diking material to separate containers for disposal. Contaminated monomer may be unstable. Add extra inhibitor to prevent<br />
polymerization. Remove contaminated clothing promptly and wash affected skin areas with soap and water. Keep spills and cleaning runoffs<br />
out of municipal sewers and open bodies of water. Spills on porous surfaces can contaminate groundwater.<br />
WASTE DISPOSAL METHOD<br />
When discarded, this material is a hazardous waste. RCRA #D-001 (ignitable); reportable quantity 1000 lbs. (40 CFR<br />
Part 302) "Superfund". Incinerate liquid and the contaminated diking material, in accordance with state and federal<br />
regulations.<br />
VII - SPECIAL PROTECTION INFORMATION<br />
VENTILATION TYPE<br />
MECHANICAL local exhaust ventilation at point of contaminant release. (See Section X)<br />
RESPIRATORY PROTECTION<br />
None required if good ventilation is maintained. Otherwise, wear self-contained breathing apparatus (pressure demand, MSHA/NIOSH<br />
approved or equivalent).<br />
PROTECTIVE GLOVES<br />
EYE PROTECTION<br />
Impervious<br />
Chemical splash goggles (AVSI Z-87.1 or approved equivalent)<br />
OTHER PROTECTIVE EQUIPMENT<br />
Eye wash facility, safety shower, imperious clothing.<br />
VII - STORAGE HANDLING INFORMATION<br />
STORAGE TEMPERATURE INDOOR HEATED REFRIGERATED OUTDOOR<br />
MAX. Ambient Min. (1)<br />
Store out of direct sunlight at ambient temperatures. <strong>Li</strong>mit indoor storage of flammable liquids to approved areas equipped with automatic sprinklers.<br />
Leave air space over liquid surface in all containers. Found all containers when transferring material. It is advisable to use material with in six months.<br />
Monitor inhibitor level during storage using CM-18. Materials stored in bulk should be tested for stability every month; drums and pails every three<br />
months.<br />
IX - TOXICITY INFORMATION<br />
Acute oral LD50 - Rat: 7900 mg/kg Acute dermal LD50 - Rabbit: 35,500 mg/kg Acute inhalation LD50 - Rat:> 12,500<br />
to 16, 500 ppm for 0.5 hours Human Patch Test: About 1/3 of 50 subjects developed a mild erythema at the site of<br />
application. 20% of subjects showed evidence of sensitivity when tested 10 test later.<br />
X - MISCELLANEOUS INFORMATION<br />
(1) Monomer stability is a logarithmic function of time vs. temperature. Stability is also dependent on inhibitor<br />
concentraion, the presence of air and type of monomer. NOTE: use local exhaust ventilation with a minimum capture<br />
velocity of 100ft/min. (30 m/min.) at the point of monomer evolution. FOOTNOTE TO SECTION I: NE = not established,<br />
NOT REQ or NR = not required.<br />
The Information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this<br />
data or the results to be obtained from the use thereof. <strong>American</strong> <strong>Tooth</strong> <strong>Industries</strong> assumes no responsibility for personal injury or property damage to<br />
Vendees, Users or third parties caused by this material. Such Vendees or Users assume all risks associated with the use of the material.<br />
Form # 244 May 94<br />
File:<strong>Pozzi</strong> <strong>Ortho</strong> <strong>Resin</strong> <strong>Li</strong>quid-Purple- MSDS .xls