RFI 002_008_013-030_2013-0402.pdf - Lord and Son Construction ...

April 2, 2013 

Mr. Duane Jones 

Lord & Son Construction 

19 David Street 

Fort Walton Beach, FL 32547 

PROJECT NO.: 12‐126 

PROJECT NAME: City of FWB Recreational Complex 

RE: 

Response to RFIs 002, 008 and 013 through 

RFI 002 

There are redundant Backflow Preventers indicated on the drawings, one DC BFP located in the system 

Riser (RP‐101 item #11), and one RPZ BFP (S‐2) located outside on the underground supply line. Please 

clarify. 

Response: See Attachments FP‐101‐A, P‐001‐A, P‐105‐A, P‐301‐A, P‐500‐A, and P‐501‐A. 


Pkg A, Drawing E6.3 Communications Systems Conduit Riser: (Note 4) How far south are we to take this 

conduit Just outside the property line All the way to Hollywood Blvd Please clarify extent. 

Response: Added note to E2.0 and indicated conduit leaving building with pull box. This conduit will go 

all the way to the front of the building on Hollywood (all City property). Approximate distance is 1,400 

ft. The drainage creek on south side of Rec Complex site may require directional bore to cross. 

Pkg B, Drawing E4.0: There is sound equipment shown in concession building, but the sound equipment 

for the ballfields has not been specified as far as we can tell. Please clarify. 

Response: Sound equipment amplifier and loudspeakers have been specified: Electro‐voice PA1250T 

amp and CFID 32‐T loudspeakers. 

Pkg B, Drawing E4.0: Note 4 says to “Provide speaker cables in 1” c to pole identified on sheet E2.0”. This 

information is not shown on Sheet E2.0. Please clarify. 

Response: Pole locations have been identified ‐ (3) total. 


3. Dugout drawings on A1.2 show a gate going into the dugout but do not show a gate going from 

the dugout to the field. I would assume they would want to go out of the dugout to the field. 

Please clarify. 

Response: Add gate from dugout to field as shown in Attachment A1.2‐A. 

RFI 014 

Specification Section 11 66 23 – Athletic Equipment 

1. 1.1 B‐1 calls for forward folding backstops, equipment schedule on A 1.3 calls for rear folding 

backstops and 2.2 C calls for fixed, stationary backstops. Please advise which method is 

required. Looks like all to be rear folding. 

Response: 

a. 1.1, B.1., shall read – Basketball Goal, ceiling suspended, rear‐folding with electric winches, 

glass backboards, new units for cross‐court play, adjustable height goal, suspension system 

and hardware. 

139 Beal Parkway SE, Suite 101 - Fort Walton Beach, Florida 32548 

dchavez@dcarchitectsinc.com ph. 850-226-8565 fax 850-362-6570

. 1.1, B.2., shall read – Basketball Goal, ceiling suspended, fixed position, glass backboards, 

new units for full‐court competition play, adjustable height goal, suspension system and 

hardware. 

2. 2.4 calls for wall pads to be used with 8 ea. Existing wall pads. (Last plan revision called for a 

total of 14 ea. New 2’x6’ wall pads.) Current A1.2 shows ONLY 4 ea. New wall pads at South end 

of gym. Please advise what quantity of new wall pads are required. 

Response: 2.4, B., shall read – qty. (4) at locations indicated on plan. 

3. A1.2 calls for scoreboards by others; however, they are still included in Section 11 66 23. Please 

confirm that there are NO scoreboards required with this section. 

Response: ‘BY OTHERS’ was indicative that they are to be donated, but still included in specifications 

for coordination purposes. 

4. 2.5 E calls for a center roll gym divider curtain. Plan sheet A1.2 shows this curtain as being 

extended from wall to the face of the bleachers in closed position; or approximately, 82’ 

wide. When in the down position, there will be no access from one side of the gym to the other 

if curtain is wall to wall. Recommendation is to provide a 76’ w. curtain allowing for an 

approximate 3’ at either end for walk through access. 

Response: To accommodate a 3’ walk access curtain shall be 76’ in width. 


There are several doors and side lite frames with glass that are to be 3 hour rated openings in 

accordance with the door schedule. We are limited to 100 square inches max size for 3/16” glass to get 

the 3 hr ratings. The door elevations called out with 3 hr ratings are a couple of E doors and a D door 

which exceed the 100 sq inches in glass. Several Firelite product data sheets attached. Please clarify how 

to proceed. 

Response: Sheet A9.0 Door Schedule: Revised door schedule as shown in Attachment A9.0A and 

Sheet A9.1 Door and Window Types: Revised door type ‘J’ as shown in Attachment A9.1A. 


1. Sheet E3.0 12 pole lighting contactor. Are these contactors mechanically or electrically held 

What amperage are these contactors 

Response: Electrically held Form C6 control required. Minimum ampacity is 60 amp for softball 

and soccer fields; 100 amp for baseball fields. Contactor ampacity cannot be less than breaker 

ampacity as indicated in panel schedules. 12‐pole contactors are not available at these 

ampacities and combinations of 4 & 5 pole contactors will have to be used. 

2. Sheet E6.1 ‐‐Note 5 requires all fixtures to be in working order before turning over to owner. 

Will all fixtures ‘even those not reinstalled at jet stadium, be required to be in working order 

Since we have no idea how many may not be working can you give us a qty for bidding 

purposes What is the wattage of these fixtures 

Response: Use quantity of fixtures to be re‐installed at Jet Stadium only. Any remaining 

additional fixtures not being installed on a pole do not have to be reworked. Fixture wattage is 

believed to be 1,500, but this has not been verified. 

Page 2 of 6


1. The height of the columns and verification of the size of the foundation and pier. If the 

information for the concrete shown on the architectural drawings is correct, then Note 03.01 

does not need to say “See structural” (the structural drawings do not include these). Also need 

size for the through bolts and any hanger requirements (simpson joist hanger number) for the 

trellis purlins. 

Response: Sheet AS1 Architectural Site Plan: Use Simpson Fasteners and hurricane clips as shown in 

Attachments AS1.0A and AS1.0B. The trellis will be 12’‐0” from finished grade to the top of the purlins as 

shown in Attachment AS1.0B. Thru bolts will be ½” galvanized steel as noted in Attachment AS1.0A. 


1. Please confirm the PLENUM cable IS or IS NOT required for Cat UTP cable. 

Response: No plenum is required. 

2. Please confirm the cable type for the floorboxes is to be OSP (gel‐filled) rated cable. 

Response: No gel is required. 


What is the height of the bottom door rails for the storefront doors The standard aluminum bottom 

door rails is 6½”. Detail 14 on sheet A9.2 scale out as a 10” bottom rail plus the height of the glass stops. 

Response: Door bottom rails shall be optional 10”. 


1. Drawing A1.1 has NOTE 10.03 stating floor mounted ballet bars @ 25'‐8" in length, but they are in 

equipment spec and call for wall mounted @ 5'‐0" in length. Can you clarify the length and 

attachment required 

Response: Double ballet barre to be wall mounted (as indicated in specs), full length wall (35’‐0”±), 

supports at 5’‐0” o.c. 

2. Side goals, call for fan shape backboards in specs, but drawings show rectangular...do you want 

rectangular or fan 

Response: Cross‐court goals to have rectangular glass backboards. 

3. Specs call for key switch operation for the divider curtain, but the TSCX2000X Control Pad is 

specified for the backstops, do you want a separate key switch for the divider curtain or have it 

operated by the control pad as well 

Response: Gymnasium Divider Curtain to be control pad operated. 


Detail 10, entitled Bollard Detail is blank. Please clarify. 

Response: Bollards are detailed in Civil. ‘BOLLARD DETAIL – 10/A5.1’ is a leftover view title with no 

references. 


Masonry thru wall flashing – Need to know if there is a spec to use. Section 04 80 10 said to see section 

07 27 00 but there is none. 

Response: Specification Section 07 27 00 added. 

Page 3 of 6

Page A8.5 keynote 07.05 self adhering bituminous flashing tape. Page A9.2 keynote 07.05 copper 

flashing. 

Response: Specification Section 07 62 00 added. 


1. Counter shutter type H in room 142 on Sheet A1.1 is in a fire rated the partition type (other 

shutter type G in same room not). Please verify fire rated requirements as the specs do not 

mention fire ratings. 

Response: Shutter type ‘H’ is to be fire rated – 45 min. See Attachment A9.1‐B. 

2. Pkg B: Counter shutter in small concession bldg. on Sheet A1.1 shows a Type A shutter which is 

scheduled to be 8’ wide, but is dimensioned at 5’ wide. Please clarify. 

Counter shutter in large concession bldg. on Sheet A1.0 is labeled as a window type B. Please 

verify this is a counter shutter Type A. 

Response: Shutter type ‘A’ modified; shutter type ‘B’ added. See Attachment A3.0‐A. 


Specification section 05 51 00 STEEL FRAMED STAIRS, Paragraph 2.4 states that stairs are to be provided 

by one of the follow: 

1. Alfab, inc. 

2. American Stair, Inc. 

3. Sharon Companies Ltd 

4. Equivalent 

Would you please clarify that it is not your intent to limit the manufacturers of steel framed stairs to 

these 3 companies and that it is acceptable for Contractors Steel Supply, Inc. to manufacture the steel 

framed stairs 

Response: Section 05 51 00 Steel Framed Stairs, Paragraph 2.4.5: Add ‘Contractors Steel Supply Inc.’ to 

approved manufacturer list. 


E7.0 states that projectors are owner furnished, but specification section 27 41 00 is in the equipment 

list to provide them. Are these owner furnished or to be provide by the AV contractor and if owner 

furnished are we to install them 

Response: See revised E7.0 attached. 


Specification Section 09 65 19 – Resilient Flooring and Base lists two different sheet vinyl floorings. Part 

2.2 is for Resilient Flooring – Sheet Vinyl 2.4 is for Slip Retardant Flooring – Sheet Vinyl. The slip resistant 

is twice the price of the standard sheet vinyl. Please clarify which sheet vinyl is to be used as the Room 

Finish Schedule on Sheet A9.0 only indicates an SHV‐Resilient Vinyl Sheet Flooring. It appears all of it 

would be the products specified under Part 2.2 of the specifications. But we want to make sure. 

Response: Slip‐Retardant Sheet Vinyl was changed to EPOXY flooring in the room finish schedule for the 

90%, this must be a leftover. 

Page 4 of 6


The suspended cloud ceiling in Specification section 09 51 23, Paragraph 2.4‐A, Item #12 indicates 14” 

Axiom trim for the edge trim at the cloud. Twelve inches is the largest produced for use in curved 

conditions. Please advise how you wish to proceed. 

Response: Axiom Classic 12” Trim Channel to be used. 


The following is an excerpt from specification section 11 52 13 – Projection Screens 

3.3 SCHEDULE 

A. Design Criteria Package “A”: Provide a total of three (3) screens for the building facility; one for 

large multi‐purpose, one for small multi‐purpose and one for staff conference room. Owner to 

verify installation locations. 

Please note that only 3 projection screens are called out. Sheet E7.0 – Floor Plan – Audio‐Visual ‐ 

indicates 2 each in the Large Multi‐purpose Room, 1 each in the Game Room and 1 each in the 

conference room for a total of 4 units. 

Please clarify. 

Response: Section 11 52 13 Projection Screens Paragraph 3.3.A revised to read ‘Design Criteria Package 

“A”: Provide a total of five (5) screens for the building facility; two for large multi-purpose, one for small 

multi-purpose, one for game room and one for conference room. Owner to verify installation locations.’ 


Reference Package B – Sheet A1.0 and A1.1 – Door Schedules for the large concessions and the small 

concession/restroom building – 

1. No hardware sets reference numbers have been provided in the door schedules. Please review 

and provide finish hardware set numbers. . 

Response: Door Schedule hardware information added. See attachments A1.0‐A and A1.1‐A. 

2. The door numbers for hardware sets noted in specification section 08 71 00 – Group 21 & 22 do 

not match the current door number for the buildings. 

Response: Specification section 08 71 00 was revised to add hardware set #23. 

Prepared by, Dennis Chavez, Architect 

Attachments: 

Section 07 27 00 – Air & Vapor Barrier System 

Section 07 62 00 – Sheet Metal Flashing & Trim 

Section 08 71 00 – Door Hardware 

S‐2‐A/U‐2‐A 

ASI1.0A 

ASI1.0B 

A1.2‐A 

A9.0A 

A9.0‐B 

A9.1A 

A9.1B 

Page 5 of 6

A1.0‐A 

A1.1‐A 

A1.2‐A 

A3.0‐A 

FP‐101‐A 

P‐001‐A 

P‐105‐A 

P‐301‐A 

P‐500‐A 

P‐501‐A 

Revised Electrical Drawings: 

Package A 

Package B 

E2.0 E1.0 

E4.1 E2.0 

E4.3 E2.1 

E6.1 E2.2 

E6.2 E3.0 

E6.3 E7.1 

E6.4 

E7.0 

E8.1 

E9.0 

Page 6 of 6

SECTION 07 27 00 – AIR & VAPOR BARRIER SYSTEM 

PART 1 – GENERAL 

1.1 SUMMARY 

A. The work of this section includes, but is not limited to, the following: 

1. Materials and installation methods for fluid applied air and vapor barrier membrane 

system located in the non-accessible part of the wall. 

2. Materials and installation methods to bridge and seal air leakage pathways in roof and 

foundation junctions, window and door openings, control and expansion joints, masonry 

ties, piping and other penetrations through the wall assembly. 

1.2 PERFORMANCE REQUIREMENTS 

A. Provide an air and vapor barrier system to perform as a continuous barrier to air infiltration/exfiltration 

and water vapor transmission and to act as a liquid water drainage plane flashed to 

discharge any incidental condensation or water penetration. 

B. The intent of this specification is to require compliance with the following regarding air leakage: 

The building envelope shall be designed and constructed with a continuous air barrier to control 

air leakage into, or out of the conditioned space. An air barrier shall also be provided for interior 

partitions between conditioned space and space designed to maintain temperature or humidity 

levels which differ from those in the conditioned space by more than 50% of the difference 

between the conditioned space and design ambient conditions. The air barrier shall have the 

following characteristics: 

1. It shall be continuous, with all joints made airtight. 

2. It shall have an air permeability not to exceed 0.004 cfm/ft2 under a pressure differential 

of 0.3 in. water (1.57 psf.) (equal to 0.02L/s/m2 @ 75 Pa.). 

3. It shall be capable of withstanding positive and negative combined design wind, fan and 

stack pressures on the envelope without damage or displacement, and shall transfer the 

load to the structure. It shall not displace adjacent materials under full load. 

4. It shall be durable or maintainable. 

5. The air barrier shall be joined in an airtight and flexible manner to the air barrier material 

of adjacent systems, allowing for the relative movement of systems due to thermal and 

moisture variations and creep. Connection shall be made between: 

a. Walls and windows, doors or louvers. 

b. Different wall systems. 

c. Wall and roof. 

d. Wall and roof over unconditioned space. 

e. Walls, floor and roof across construction, interior control and expansion joints. 

f. Walls, floors and roof to utility, pipe and duct penetrations. 

C. Air barrier penetrations: 

All penetrations of the air barrier and paths of air infiltration/exfiltration shall be made airtight. 

1.3 REFERENCES 

A. The following standards and publications are applicable to the extent referenced in the text. 

The most recent version of these standards is implied unless otherwise stated. 

City of Fort Walton Beach Air & Vapor Barrier System 07 27 00 – 1 

Recreational Complex

B. American Society for Testing and Materials (ASTM) 

1. C 836 Standard Specification for High Solids, Cold Liquid-Applied Elastomeric 

Waterproofing Membrane for Use with Separate Wearing Course 

2. D 412-87 Standard Test Methods for Rubber Properties in Tension 

3. D 903-83 Standard Test Method for Peel or Stripping Strength of Adhesive Bonds 

4. D 1644-93 Test Methods for Non-volatile Content of Varnishes 

5. D 1970-94 Standard Specification for Self-Adhering Polymer Modified Bituminous 

Sheet Materials Used as Steep Roofing Underlayment for Ice Dam 

Protection 

6. D 4541-02 Standard Test Method for Pull-Off Strength of Coatings Using Portable 

Adhesion Testers 

7. D 3767-92 Standard Practice for Rubber - Measurements of Dimensions 

8. E 96-95 Test Methods for Water Vapor Transmission of Materials 

9. E 2178-01 Standard Test Method for Air Permeance of Building Materials 

10. E 283-91 Standard Test Method for Determining the Rate of Air Leakage Through 

Exterior Windows, Curtain Walls, and Doors Under Specified Pressure 

Differences Across the Specimen 

1.4 SUBMITTALS 

A. Product Data: Submit manufacturer’s product data, installation instructions, use limitations and 

substrate preparation recommendations. 

B. Shop drawings showing locations and extent of air and vapor barrier system including details 

for terminations flashings, penetrations, window and door openings and treatment of substrate 

joints and cracks. 

C. Written documentation demonstrating installers qualifications under the "Quality Assurance" 

article including reference projects of a similar scope. 

D. Samples: Submit representative samples of the following for approval: 

1. Fluid applied membrane 

2. Transition tape 

3. Through Wall Flashing 

E. Warranty: Submit a sample warranty identifying the terms and conditions stated in Paragraph 

1.8–A. – “WARRANTY”. 

1.5 QUALITY ASSURANCE 

A. Manufacturer: Air and vapor barrier systems shall be manufactured and marketed by a firm 

with a minimum of 20 years experience in the production and sales of waterproofing. 

Manufacturers proposed for use, but not named in these specifications shall submit evidence of 

ability to meet all requirements specified, and include a list of projects of similar design and 

complexity completed within the past five years. 

B. Installer: The installer shall demonstrate qualifications to perform the work of this Section by 

submitting the following: 

1. List of at least three (3) projects contracted within the past five (5) years of similar scope 

and complexity to this project carried out by the firm and site supervisor. 

2. Installer must show evidence of adequate equipment and trained field personnel to 

successfully complete the project in a timely manner. 



C. Materials: Fluid applied air and vapor barrier material shall be two part synthetic rubber based 

systems free of solvents, isocyanates and bitumen. For each type of material required for the 

work of this section, provide primary materials that are the products of one manufacturer. 

D. Mock-up: 

1. Prior to installation of the air and vapor barrier system a field-constructed mock-up shall 

be provided under the provisions of Section [01340 – Shop Drawings, Product Data, 

Samples and Mock-ups] to verify details and tie-ins and to demonstrate the required 

quality of materials and installation. 

2. Construct a typical exterior wall section, 5’-0’ feet high and 4’-0” feet wide, incorporating 

back-up wall, cladding, window and doorframe and sill, insulation, flashing and any other 

critical junction (roof, foundation, etc). 

3. Allow 24 hours for inspection and testing of mock-up before proceeding with air and 

vapor barrier work. 

4. Approved mock-up to be removed from site. 

F. Inspection and Testing: Cooperate and coordinate with the Owner’s inspection and testing 

agency. Do not cover any installed air and vapor barrier membrane until it has been inspected, 

tested and approved. 

1.7 WARRANTY 

A. Submit manufacturer's warranty that air and vapor barrier and accessories are free of defects at 

time of delivery and are manufactured to meet manufacturer's published physical properties and 

material specifications. 

PART 2 – PRODUCTS 

2.1 GENERAL 

For each type of material required for the work of this section, provide primary materials that are 

the products of one manufacturer. 

2.2 TRANSITION TAPE 

A. Description: 0.9 mm (36 mils) of self-adhesive rubberized asphalt integrally bonded to 0.1 mm 

(4 mil) of cross-laminated, high-density polyethylene film to provide a min. 0.1 mm (40 mil) thick 

membrane. Membrane shall be interleaved with disposable silicone-coated release paper until 

installed. 

B. Performance Requirements: 

1. Water Vapor Transmission: ASTM E 96, Method B: 2.9 ng/m2sPa (0.05 perms) max. 

2. Air Permeance at 75Pa (0.3 in. water) pressure difference: 0.0006 L/(s.m 2 ) (0.00012 

cfm/ft 2 ) max. 

3. Puncture Resistance: ASTM E 154: 178 N (40 lbs.) min. 

4. Lap Adhesion at –4°C (25°F): ASTM D 1876: 880 N/m (5.0 lbs./in.) of width min. 

5. Low Temperature Flexibility ASTM D 1970: Unaffected to –43°C (-45°F). 

6. Tensile Strength: ASTM D 412, Die C Modified: min. 2.7 MPa (400 psi) 

7. Elongation, Ultimate Failure of Rubberized Asphalt: ASTM D 412 Die C: min. 200% 

C. Acceptable Materials: 



Perm-A-Barrier Wall Membrane manufactured by Grace Construction Products. 

2.3 FLEXIBLE MEMBRANE WALL FLASHING 

A. Description: 0.8 mm (32 mils) of self-adhesive rubberized asphalt integrally bonded to 0.2 mm 

(8 mil) of cross-laminated, high-density polyethylene film to provide a min. 1.0 mm (40 mil) thick 

membrane. Membrane shall be interleaved with disposable silicone-coated release paper until 

installed. 

B. Performance Requirements: 

1. Water Vapor Transmission: ASTM E 96, Method B: 2.9 ng/m2sPa (0.05 perms) max. 

2. Water Absorption: ASTM D 570: max. 0.1% by weight 

3. Puncture Resistance: ASTM E 154: 356 N (80 lbs.) min. 

4. Tear Resistance 

a. Initiation ASTM D 1004: min. 58 N (13.0 lbs.) M.D. 

b. Propagation ASTM D 1938: min. 40 N (9.0 lbs.) M.D. 

5. Lap Adhesion at -4ºC (25ºF): ASTM D 1876: 880 N/m (5.0 lbs./in.) of width 

6. Low Temperature Flexibility ASTM D 1970: Unaffected to -43ºC (-45ºF) 

7. Tensile Strength: ASTM D 412, Die C Modified: min. 5.5 MPa (800 psi) 

8. Elongation, Ultimate Failure of Rubberized Asphalt: ASTM D412, Die C: min. 200% 

C. Acceptable Materials: 

Perm-A-Barrier Wall Flashing manufactured by Grace Construction Products. 

2.4 AIR & VAPOR BARRIER ACCESSORIES 

A. Description: Water-based primer which imparts an aggressive, high tack finish on the treated 

substrate 

1. Flash Point: No flash to boiling point 

2. Solvent Type: Water 

3. VOC Content: Not to exceed 10 g/l 

4. Application Temperature: -4°C (25°F) and above 

5. Freezing point (as packaged): -7°C (21°F) 

Product: Perm-A-Barrier WB Primer manufactured by Grace Construction Products. 

B. Description: two part, elastomeric, trowel grade material designed for use with self-adhered 

membranes and tapes. 10 g/l max. VOC Content. 

Product: Bituthene ® Liquid Membrane manufactured by Grace Construction Products. 

C. Optional Primers: 

1. Description: High tack water based primer. 10 g/l max. VOC content. 

Product: Perm-A-Barrier Liquid Part B manufactured by Grace Construction Products. 

2. Description: High tack solvent based primer. 440 g/l max. VOC content. 

Product: Bituthene Primer B2 manufactured by Grace Construction Products. 

PART 3 – EXECUTION 

3.1 EXAMINATION 



A. The installer shall examine conditions of substrates and other conditions under which this work 

is to be performed and notify the contractor, in writing, of circumstances detrimental to the 

proper completion of the work. Do not proceed with work until unsatisfactory conditions are 

corrected. 

3.2 PREPARATION 

A. Refer to manufacturer’s literature for requirements for preparation of substrates. Surfaces shall 

be sound and free of voids, spalled areas, loose aggregate and sharp protrusions. Remove 

contaminants such as grease, oil and wax from exposed surfaces. Remove dust, dirt, loose 

stone and debris. Use repair materials and methods that are acceptable to manufacturer of the 

fluid-applied waterproofing. 

B. Exterior sheathing panels: Ensure that the boards are sufficiently stabilized with corners and 

edges fastened with appropriate screws. Pre-treat all board joints with 50 - 75mm (2-3 in.) 

wide, reinforced self-adhesive tape or fiberglass mesh style wallboard tape. Gaps greater than 

6mm (1/4 in.) should be filled with mastic or caulk, allowing sufficient time to fully cure before 

application of the tape and fluid applied membrane. 

C. Masonry Substrates: Apply air and vapor barrier over concrete block and brick with smooth 

flush mortar joints. Fill all voids and holes, particularly in the mortar joints, with a lean mortar 

mix, non-shrinking grout or parge coat. 

D. Related Materials: Treat construction joints and install flashing as recommended by 

manufacturer. 

3.3 INSTALLATION 

A. Refer to manufacturer’s literature for recommendations on installation 

B. Application of Transition Membrane 

1. After allowing the Fluid Applied Membrane to cure to tack-free, apply transition 

membrane with a minimum overlap of 3 in. onto each surface at all beams, columns and 

joints as indicated in detail drawings. 

2. Tie in to window and door frames, spandrel panels, roof and floor intersections and 

changes in substrate. 

3. Use pre-cut, easily handled lengths for each location. 

4. Remove silicone-coated release paper and position membrane flashing carefully before 

placing it against the surface. 

5. When properly positioned, place against surface by pressing firmly into place by hand 

roller. 

6. Overlap adjacent pieces 50 mm ( 2 in.) and roll all seams with a hand roller. 

7. Seal top edge of flashing with termination mastic. 

8. When transition flashing is pre-installed prior to application of Fluid Applied Membrane, 

apply transition flashing as above. Spray or trowel a continuous uniform film of Fluid 

Membrane at min. 60 mils (1.5 mm or .060 in.) dry film thickness using multiple, 

overlapping passes, with a minimum overlap of 75 mm (3 in.) onto transition flashing. For 

sill condition, spray or trowel Fluid Membrane onto pre-installed sill flashing and onto 

horizontal section of sill. 

C. Application of Flexible Membrane Wall Flashing 

1. Precut pieces of flashing to easily handled lengths for each location. 



2. Remove silicone-coated release paper and position flashing carefully before placing it 

against the surface. 

3. When properly positioned, place against surface by pressing firmly into place by hand 

roller. Fully adhere flashing to substrate to prevent water from migrating under flashing. 

4. Overlap adjacent pieces 2 in. and roll all seams with a hand roller. 

5. Trim bottom edge 1/2 in back from exposed face of the wall. Flashing shall not be 

permanently exposed to sunlight. 

6. At heads, sills and all flashing terminations, turn up ends a minimum of 4 in. and make 

careful folds to form an end dam, with the seams sealed. 

7. Seal top edge of flashing with termination mastic. 

8. Do not allow the rubberized asphalt surface of the flashing membrane to come in contact 

with poly-sulfide sealants, creosote, uncured coal tar products or EPDM. 

3.4 PROTECTION AND CLEANING 

A. Remove any masking materials after installation. Clean any stains on materials that would be 

exposed in the completed work using procedures as recommended by manufacturer. 

B. Specified material is not suitable for permanent exposure and should be protected from the 

effects of sunlight. 

C. Schedule work to ensure that the specified material is covered as soon as possible after 

installation. Protect specified material from damage during subsequent operations. If the 

specified material cannot be covered within 60 days after installation, apply temporary UV 

protection such as dark plastic sheet or tarpaulins. 

END OF SECTION 07 27 00 



SECTION 07 62 00 - SHEET METAL FLASHING AND TRIM 


A. Quality Standard(s): SMACNA's "Architectural Sheet Metal Manual" and CDA's 

"Copper in Architecture Handbook". 

1.2 WARRANTY 

A. Special Warranty on Painted Finishes: Manufacturer's standard form in which 

manufacturer agrees to repair finish or replace roof specialties that show evidence of 

deterioration of factory-applied finishes within specified warranty period. 

1. Fluoropolymer Finish: Deterioration includes, but is not limited to, the following: 

a. Color fading more than 5 Hunter units when tested according to 

ASTM D 2244. 

b. Chalking in excess of a No. 8 rating when tested according to 

ASTM D 4214. 

c. Cracking, checking, peeling, or failure of paint to adhere to bare metal. 

2. Finish Warranty Period: 10 years from date of Substantial Completion. 

1.3 MATERIALS 

A. Sheet Metals: 

1. Copper Sheet: Non-patinated mill finish. 

B. Exposed Metals: 

1. Hot dipped galvanized steel sheets, as standard with manufacturer for finish 

required, with temper to suit forming operations and performance required. 

a. Surface: Smooth, flat finish. 

b. Exposed Coil-Coated Finishes: Prepare, pretreat, and apply coating to 

exposed metal surfaces to comply with coating and resin manufacturers' 

written instructions. 

1) Three-Coat Fluoropolymer: AAMA 620. System consisting of primer, 

fluoropolymer color coat, and clear fluoropolymer topcoat, with both color 

coat and clear topcoat containing not less than 70 percent PVDF resin by 

weight. 

1.4 PRODUCTS 

A. Manufactured Flashing and Trim: 

1. Reglets and Counterflashing: Galvanized steel. 

a. Type: Masonry. 

City of Fort Walton Beach Sheet Metal Flashing and Trim 07 62 00 – 1 


. Accessories: Counterflashing wind-restraint clips. 


City of Fort Walton Beach Sheet Metal Flashing and Trim 07 62 00 – 2 


SECTION 08 71 00 – DOOR HARDWARE 

PART 1 – GENERAL 

1.01 SECTION INCLUDES 

A. All items known commercially as Finish or Door Hardware. 

B. Thresholds and Weatherstripping/Door Seals. 

1.02 REFERENCES 

A. BHMA (Builders Hardware Manufacturers Association) A156 series. 

B. ANSI/DHI A115.IG – 1994 Installation Guide for Doors and Hardware. 

C. ANSI A250.6 – 1997 Recommended Practice for Hardware Reinforcing on Steel Doors and 

Frames 

D. ANSI A156.115 – 2006 Recommended Hardware Locations for Wood Doors. 

E. NFPA – 80 – Fire Doors and Windows. 

F. NFPA – 101-2000 - Life Safety Code. 

G. ADA – Americans with Disabilities Act. 

H. ANSI A250.13 Wind Resistant Building Components Testing. 

I. All Applicable Local and State Codes 

1.03 SUBMITTALS 

A. Procedures of Division 1, Section 01330 – Submittal procedures apply to this section. 

B. Product Data – Submit two (2) copies of manufacturer’s catalog sheets describing each item 

of hardware to be supplied. 

C. Schedules – Submit six (6) copies of hardware schedules for Architect’s approval. 

Schedules are to include quantity, type, location, finish and manufacturer of each item of 

hardware for each opening. Schedule may be horizontal or vertical format. No material is 

to be ordered until the submittal is approved. After approval, no substitutions will be allowed 

without the written approval of the Architect. 

D. Samples – If requested by the Architect, submit a sample of each hardware item in the 

design and finish to be used on the project. Samples may be used on the project provided 

they are undamaged during the submittal process. 

E. Templates – Furnish template information to the General Contractor for use by other trades 

in fabricating related materials. 

F. Project Closeout – On completion of the project, furnish one (1) copy of the “as 

furnished” hardware schedule along with one (1) copy each of the keying schedule. 

manufacturer’s maintenance instructions and any special tools which may be required 

to maintain or adjust the hardware. In addition, furnish copies of all manufacturer’s 

warranties for the owner’s records. 


A. Manufacturers and model numbers listed in the hardware sets portion of this specification 

are for the purpose of establishing a standard of quality. Similar products by approved 

City of Fort Walton Beach Door Hardware 08 71 00 – 1 


manufacturers that are equal in design, function and quality will be acceptable upon prior 

approval of the Architect provided the required physical samples and data are submitted in 

accordance with Section 01600. 

B. The hardware supplier shall be a firm specializing in finish hardware. The firm shall have 

been engaged in this business for a period of not less than five (5) years and shall have in 

its employ a full time, certified Architectural Hardware Consultant (AHC) or person of 

equivalent experience. This person shall be available to the Architect at reasonable times 

for consultation regarding this project. This supplier shall be a direct, factory authorized 

distributor for the manufacturer of the materials being furnished. 

C. The hardware manufacturer shall be a recognized firm regularly engaged in the 

manufacture and sale of finished hardware items. 

D. If required, the hardware supplier shall furnish certification and documentation that his 

materials meet all physical and environmental requirements of the project. 

E. As near as possible, obtain each type of hardware (hinges, locks, closers, etc.) from a 

single manufacturer. 

F. Provide hardware for fire rated openings that complies with the requirements of NFPA 80 

and authorities having jurisdiction. Provide only items of door hardware that have been 

tested and listed by UL, FM, Warnock-Hersey or other testing organizations acceptable 

to the authorities having jurisdiction. 

G. All hardware shall meet the requirements set forth in the Americans with Disabilities Act 

(ADA) and state and local handicapped codes. 

1.05 DELIVERY, STORAGE AND PROTECTION 

A. Section 01600 pertaining to transportation, handling and storage of project materials 

applies to this section. 

B. Package each item individually. Label and clearly identify each package with item 

nomenclature and door opening. Correlate all making and opening numbers to match 

the hardware schedule. 

C. The General Contractor is to provide a secure, locked storage area for all items delivered 

to the jobsite. 

D. The General Contractor shall inventory all items delivered to the jobsite within forty-eight 

hours and advise the supplier immediately of any shortages. 

1.06 PROJECT CONDITIONS 

A. The General Contractor will coordinate the work between this supplier and other related 

sections such as hollow metal and wood door suppliers to insure proper manufacturer 

and fabrication of doors to receive the approved hardware. 

1.07 WARRANTY 

A. All hardware items are to be warranted for a period of one (1) year from date of substantial 

project completion. Door closers are to be warranted for five (5) years. 

B. Warranty is to cover failure due to manufacturing defects or material failure only. 

It shall not cover abuse, vandalism, improper installation or maintenance. Defective 

materials are to be replaced at no cost to the owner. 



PART 2 – PRODUCTS 

2.01 MANUFACTURERS 

A. Acceptable products and their manufacturers are listed below. Specific information 

regarding functions, sizes, mounting and types is found in the hardware sets at the 

end of the section. 

1. Hinges 

MFG’R FINISH TYPE/SERIES 

a. McKinney 26D/CL 

TA2714/T4A3786/TA4895/T4A4795/MCK12HD 

b. Stanley 26D/CL 

FBB179/FBB168/CB258/CB278/661HD 

c. Hager 26D/CL 

BB1279/BB1168/BB1261/BB1263/780-112HD 

2. Exit Devices 

MFG’R FINISH SERIES/DESIGN 

a. Cor/Russ 32D ED5000 Series 

No Substitute 

3. Locks, Latches and Dummy Trim 


a. Cor/Russ 26D ML2000 Series x CSA Trim 

No Substitute 

4. Cylinders, Deadlocks & Misc. Locks 


a. Cor/Russ 26D 1080/3080/DL4013 

b. Sargent 26D P 114 

No Substitute 

5. Closers 


a. Cor/Russ 689 DC8000 Series 

Furnish as specified to match existing 

6. Push/Pulls/Kickplates 


a. Rockwood 32D As Specified 

b. Hager 32D Equal 

c. Ives 32D Equal 

7. Overhead Stops 


a. Rockwood 32D 19000/14400 Series 

b. G-J 32D 90/450 Series 

c. ABH 32D 9000/4400 Series 

8. Stops and Miscellaneous Items 

MFG’R FINISH ITEM 

a. Rockwood 32D/26D 409/443 

b. Hager 32D/26D 236W/243F 



c. Ives 32D/26D W407CCV/FS438 

9. Thresholds and Weatherstripping 

MFG’R FINISH TYPE/ITEM 

a. Pemko AL AS SPECIFIED 

b. Hager AL EQUAL 

c. National Guard AL EQUAL 

B. Substitutions – Substitutions from the listed manufacturers and products without 

prior approval of the architect are not permitted. Suppliers desiring to bid products 

not listed must make written application to the architect no less than seven (7) 

working days prior to the bid date. Applications must be accompanied by 

manufacturers complete literature and/or samples to allow the Architect to make 

an informed decision. Verbal request will not be considered. Approval of 

alternate manufacturers products will be by addendum at least two (2) days 

prior to bid date to insure an equitable competitive situation for all bidders. 

2.02 MATERIALS AND FABRICATION 

A. Base Metals – Produce hardware units of basic metal and forming method indicated 

using manufacturer’s standard metal alloy, composition, temper and hardness, but 

in no case of lesser (commercially recognized) quality than specified for applicable 

hardware units for finish designations indicated. 

B. Fasteners – Provide hardware manufactured to conform to published templates, 

generally prepared for machine screw installation. Do not provide hardware that 

has been prepared for self-tapping sheet metal screws, except as specifically 

indicated. 

C. Furnish screws for installation with each hardware item. Provide Phillips flat-head 

screws except as otherwise indicated. Furnish exposed (exposed under any 

condition) screws to match hardware finish or if exposed in surfaces of other work, 

to match finish of this other work as closely as possible including “prepared for 

paint” surfaces to receive painted finish. 

D. Provide concealed fasteners for hardware units that are exposed when door is 

closed except to the extent no standard units of type specified are available with 

concealed fasteners. Do not use thru-bolts for installation where bolt heads or 

nuts are exposed on opposite face unless their use is the only means of adequately 

securing the hardware or where required on labeled doors. In no case are 

thru-bolts to be used as a substitute for proper reinforcement of doors or frames. 

2.03 FINISHES 

A. Finishes for all items are as listed in the hardware schedule at the end of this 

section. 

B. Finish designations are as listed in ANSI/BHMA A156.18 “American Standards 

for Materials and Finishes: and are the industry recognized standard commercial 

finishes. 

2.04 KEYING 

A. Key all cylinders into the existing Corbin Russwin GMK system as directed. Furnish six (6) or 

seven (7) pin cylinders. Meet with owner’s representative to determine exact keying 

requirements. Furnish keyed temporary cores for each lock (Cylinder). Send permanent 

cores and keys direct from factory to Owner. Notify Owner’s Representative when shipment 

is made. Return construction cores to distributor for credit. 

Furnish keys as follows: 



6 Master Keys per new group 

6 Construction Master Keys 

3 Control Keys 

3 Keys per cylinder 

B. Furnish a key control system including cabinet with a capacity of 100% of key 

changes on project plus 25% expansion, tags, envelopes, loan register and 

cards. System to be equal to Key Control Systems, Inc. “PLR” system. Equal 

products by Telkee or Lund are acceptable. 

PART 3 – EXECUTION 

3.01 INSTALLATION 

A. Mount hardware units at heights indicated in following applicable publications, 

except as specifically indicated or required to comply with governing regulations 

and except as otherwise directed by architect. 

1. “Recommended Locations for Builders Hardware for Standard Steel Doors 

and Frames” by the DOOR AND HARDWARE INSTITUTE. 

a. WDMA Industry Standard I.S. 1.A-97, “Hardware Locations for Wood Flush 

Doors.” 

B. Install each hardware item in compliance with the manufacturer’s instructions and 

recommendations. Where cutting and fitting is required to install hardware onto or 

into surfaces that are later to be painted or finished in another way, coordinate removal, 

storage, and reinstallation or application of surface protection with finishing work 

specified in the Division 9. Do not install surface-mounted items until finishes have been 

completed on the substrates involved. 

C. Set units level, plumb, and true to line and location. Adjust and reinforce the attachment 

substrate as necessary for proper installation and operation. 

D. Drill and countersink units that are not factory prepared for anchorage fasteners. Space 

fasteners and anchors in accordance with industry standards. 

E. Set thresholds in sealant complying with requirements specified in Section 07100 – 

Dampproofing and Waterproofing. 

F. Weatherstripping and Seals: Comply with manufacturer’s instructions and 

recommendations to the extent installation requirements are not otherwise indicated. 

3.02 JUSTING AND CLEANING 

A. Adjust and check each operating item of hardware and each door to ensure proper 

operation or function of every unit. Replace units that cannot be adjusted to operate 

freely and smoothly or as intended for the application made. 

B. Where door hardware is installed more than one month prior to acceptance or occupancy 

of a space or area, return to the installation during the week prior to acceptance or 

occupancy and make final check and adjustment of all hardware items in such space or 

area. Clean operating items as necessary to restore proper functions and finish of hardware 

and doors. Adjust door control devices to compensate for final operation of heating and 

ventilating equipment. 

C. Clean adjacent surfaces soiled by hardware applications. 

3.03 HARDWARE SCHEDULE 



A. Hardware Sets 

Group # 1 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 

1 LOCKSET ML2051 CSA CT6R 626 CR 

1 CORE 8000 626 CR 

1 WALL BUMPER 409 US32D RO 

3 DOOR SILENCERS 608 GREY RO 

Group # 2 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 

1 PRIVACY SET ML2020 CSA 626 CR 



Group # 3 

EACH TO HAVE: 

1 CONTINUOUS HINGE MCK-12HD 83 QC4 CLEAR MC 

1 CORE 8000 626 CR 

1 CLOSER DC8210 A4 689 CR 

1 PROTECTION PLATE K1050 10" X 34" US32D RO 

1 THRESHOLD 2005 AV X 36" PE 

1 WEATHER SEAL S88 BL 17' PE 

1 DOOR BOTTOM 345 AV X 36" PE 

1 RAINDRIP 346 C X 40" PE 

Group # 4 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 


1 CORE 8000 626 CR 

1 CLOSER DC8200 689 CR 




Group # 5 

EACH TO HAVE: 

1 CYLINDER 3080-178-6 CT6R 626 CR 

OR 

1 CYLINDER 1080-114-A02-6 626 CR 

1 CORE 8000 626 CR 

BALANCE OF HARDWARE BY DOOR SUPPLIER 

CONTACT DOOR SUPPLIER FOR CYLINDER TYPE AND FINISH 



Group # 6 

EACH TO HAVE: 

6 HINGES T4A3786 4 1/2 X 4 1/2 26D MC 

2 FIRE EXIT DEVICE ED5400A X C955 CT6R M55 630 CR 

2 CORE 8000 626 CR 




Group # 7 

EACH TO HAVE: 

3 HINGES T4A3786 4 1/2 X 4 1/2 26D MC 

1 HOSPITAL LATCH P 114 26D SA 



1 DOME STOP 443 US26D RO 


Group # 8 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 


1 CORE 8000 626 CR 




Group # 9 

EACH TO HAVE: 

6 HINGES TA2714 4 1/2 X 4 1/2 26D MC 

2 FLUSH BOLTS 555 US26D RO 

1 DUST PROOF STRIKE 570 US26D RO 


1 CORE 8000 626 CR 

1 OVERHEAD STOP 14423 US32D RO 



Group # 10 

3 HINGES TA4895 4 1/2 26D MC 


1 CORE 8000 626 CR 







GROUP # 11 

EACH TO HAVE 

6 HINGES T4A3786 4 ½ X 4 ½ 26D MC 

2 FIRE EXIT DEVICE ED5400A X C955 CT6R M55 630 CR 

2 CORE 8000 626 CR 


2 PROTECTION PLATE K1050 10” X 34” US32D RO 

2 DOOR SILCENCERS 608 GREY RO 

Group # 12 

EACH TO HAVE: 

3 HINGES T4A4795 4 1/2 26D MC 

1 DEADLOCK DL4013 CT6R 626 CR 

1 CORE 8000 626 CR 

1 PUSH PLATE 70F 8 X 16 US32DBIO RO 

1 DOOR PULL 110 X 70C US32DBIO RO 





Group # 13 

3 HINGES T4A4795 4 1/2 26D MC 

1 CORE 8000 626 CR 





Group # 14 

EACH TO HAVE: 

2 CONTINUOUS HINGE MCK-12HD 83 CLEAR MC 

2 SURFACE BOLT 585-12 US32D RO 


1 CORE 8000 626 CR 

2 OVERHEAD HOLDER 19013 US32D RO 



Group # 15 

EACH TO HAVE: 


1 EXIT DEVICE ED5200S X T957 CT6R M107 M94 630 CR 

1 CORE 8000 626 CR 









Group # 16 



1 EXIT DEVICE ED5200S X T950 M107 630 CR 


1 LOCKABLE MULLION WS707AKM CT6R CR 

2 CORE 8000 626 CR 







Group # 17 



1 CORE 8000 626 CR 







Group # 18 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 

1 PASSAGE SET ML2010 CSA 626 CR 





Group # 19 

EACH TO HAVE: 

3 HINGES TA2714 4 1/2 X 4 1/2 26D MC 

1 PASSAGE SET ML2010 CSA 626 CR 



Group # 20 



1 EXIT DEVICE ED5200S X T950 M107 630 CR 


1 LOCKABLE MULLION WS707AKM CT6R CR 

2 CORE 8000 626 CR 





Group # 21 

3 HINGES TA4895 4 1/2 26D MC 


1 CORE 8000 626 CR 






Group # 22 



1 CORE 8000 626 CR 







Group # 23 

6 HINGES TA4895 4 1/2 26D MC 


1 CORE 8000 626 CR 

1 FLUSH BULTS 555 US26D RO 






NOTES: 

1. Mount all closers inside; away from exterior, lobbies, corridors, etc. Furnish brackets for 

proper mounting. 

2. Furnish proper fasteners for wall bumpers and door stops to be compatible with wall or 

floor conditions. 

3. All exterior items to meet hurricane wind speed requirements coordinated with the door 

manufacturer. Submit Florida Product Approval numbers for required item. 




FWB Recreational Complex Attachment S-2-A / U-2-A Package A / B

RFI 17 Attachment AS1.0 B FWB Recreation Complex

GENERAL NOTES: 

A. REFER TO CIVIL, STRUCTURAL, MECHANICAL & ELECTRICAL FOR 

ADDITIONAL INFORMATION. 

B. ENTRY SIDEWALK IS TO TIE INTO EXISTING SIDEWALK ALONG JET DRIVE, 

SEE CIVIL. 

KEYNOTES: 

01 GENERAL 

01.01 PROPOSED LOCATION OF RECREATIONAL BUILDING. 

03 CONCRETE 

03.01 CONCRETE FOOTING, SEE STRUCTURAL. 

03.02 3000 PSI MIN. CONCRETE OVER COMPACTED FILL. 

03.03 (4) #5 BARS, EA. WAY. 

03.04 (4) #5 VERTICAL BARS w/ 6" LEG, 2" HOOK, and #3 TIES @ 12" O.C. 

04 MASONRY 

04.01 8" CMU, PRIME / PAINT, SEE STRUCTURAL. 

05 METALS 

05.01 

1 4 " GALV. STEEL EMBEDDED POST BASE. 

05.02 

1 2 " GALV. STEEL THRU-BOLTS w/PLUGS. 

06 WOOD, PLASTICS & COMPOSITES 

06.01 8 x 8 P.T. WOOD POST, STAINED. 

06.02 (2) 2 x 10 P.T. WOOD BEAM, STAINED. 

06.03 2 x 8 P.T. WOOD PURLINS @ 24" O.C., STAINED. 

06.04 SIMPSON STAINLESS STEEL H1 HURRICANE TIES EA. END OF 

PURLIN - INSTALL WITH FLANGES FACING INWARD AS SHOWN 

06.05 SIMPSON STAINLESS STEEL A44 FASTENER. 

10 SPECIALTIES 

10.01 35' ht. FLAGPOLE, SET IN PVC SLEEVE w/CONCRETE FOOTING. 

12 FURNISHINGS 

12.01 (15) SPACE BICYCLE RACK, INSTALL PER MANUFACTURER 

INSTRUCTIONS, SEE SPECS. 

23 HEATING, VENTILATION & AIR CONDITIONING 

23.01 PROPOSED LOCATION OF OUTDOOR MECHANICAL EQUIPMENT. 

26 ELECTRICAL 

26.01 PROVIDE NEW SITE LIGHTING PER ELECTRICAL DRAWINGS & 

SPECIFICATIONS. 

26.02 PROPOSED LOCATION OF BACKUP GENERATOR, BY OWNER. SEE 

ELECTRICAL. 

26.03 PROPOSED LOCATION OF POWER TRANSFORMER, SEE 

ELECTRICAL. 

31 EARTHWORK 

31.01 GRAVEL FILL. 

32 EXTERIOR IMPROVEMENTS 

32.01 SIDEWALK, SEE CIVIL. 

32.02 REFER TO CIVIL DRAWINGS FOR STRIPING AND PARKING LOT 

MODIFICATIONS. 

32.03 PROVIDE ADA PARKING SIGNAGE IN LOCATIONS SHOWN PER CIVIL 

DRAWINGS. 

32.04 REFER TO LANDSCAPE DRAWINGS FOR IRRIGATION & PLANTING 

PLANS. 

32.05 BRICK PAVER SET OVER SAND BED w/FILTER CLOTH, INSTALL PER 

MANUFACTURER INSTRUCTIONS. 

RFI 17 Attachment AS1.0 A FWB Recreaton Complex

11 EQUIPMENT 

11.11 BASKETBALL GOAL / CURTAIN CONTROL PANEL & KEYPAD, SEE 

ELECTRICAL. MOUNT SIGN (45) DIRECTLY ABOVE KEYPAD. 

23.5' 

23.5' 

23.5' 

23.5' 

SL 

FWB Recreational Complex Attachment A1.2-A Package A

RFI 15 Attachment A9.0 A FWB Recreation Complex

SIGNAGE SCHEDULE 

SIGNAGE DETAIL 

• MOUNT @ 5'-0" ABOVE FINISHED FLOOR TO CENTER LINE OF SIGN. 

• LETTERS AND NUMERALS SHALL BE RAISED 1/32", UPPER CASE, SANS SERIF, AND 

SHALL BE ACCOMPANIED WITH GRADE 2 BRAILLE. 

• COLORS: BACKGROUND FIELD: TO BE SELECTED BY OWNER. 

LETTERS, NUMBERS & SYMBOLS: TO BE SELECTED BY OWNER. 

• LETTERS AND NUMBERS SHALL HAVE A WIDTH-TO-HEIGHT RATIO OF BETWEEN 

3:5 AND 1:1, AND A STROKE-WIDTH-TO-HEIGHT RATIO BETWEEN 1:5 AND 1:10. 

8" 

4" 

 

 

SIGN 'A' 

8" 

A 

B 

8" 

SIGN 'B' 

5" 

8" 

 

SIGN 'C' 

MOUNT ADJACENT 

TO DOOR / OPENING 

GENERAL NOTES 

A. FOR SIGN TYPES, SEE SPECIFICATIONS. 

B. PRIOR TO FABRICATION, VERIFY SIGNAGE COPY WITH OWNER. 

C. OWNER TO PROVIDE ROOM NUMBERS. 

FWB Recreational Complex Attachment A9.0-B Package A

SOLID CORE WOOD PAIR OF DOORS 

w/TEMPERED GLASS, 

HOLLOW METAL FRAME 

w/PAINTED FINISH 

RFI 15 Attachment A9.1 A FWB Recreation Complex

ROLLING COUNTER SHUTTER 

w/SPEC'D FINISH 



FIRE RATING - 45 MIN. 

FIXED LOUVER SHUTTER 


UNIT INSTALLED TO BE 'REMOVABLE' FOR 

MECHANICAL UNIT SERVICE / REPLACEMENT 

FWB Recreational Complex Attachment A9.1-B Package A

DOOR SCHEDULE 

REMARKS: 

FWB Recreational Complex Attachment A1.0-A Package B

DOOR SCHEDULE 

REMARKS: 








FWB Recreational Complex Attachment P-001-A Package A





FWB Recreational Complex Attachment FP-101-A Package A

RFI 002_008_013-030_2013-0402.pdf - Lord and Son Construction ...

Create successful ePaper yourself

Delete template?

Save as template?