Download MEW E101 April 2013 (pdf, 280kb) - NSW Public Works
Download MEW E101 April 2013 (pdf, 280kb) - NSW Public Works
Download MEW E101 April 2013 (pdf, 280kb) - NSW Public Works
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Part 2 - Switchboards and Associated Equipment<br />
202.1.2 Custom-built Assembly Type “CT”<br />
The following details shall apply to Custom-built Assemblies Type “CT”:<br />
(a) A Type “CT” assembly shall be a stationary “cubicle-type assembly” as defined in<br />
AS/NZS 3439.1:2002.<br />
(b) A Type “CT” assembly shall comply with AS/NZS 3439.1:2002 as defined by the<br />
following requirements:<br />
(i) Form of separation shall be Form 1.<br />
(ii) The degree of protection after installation in accordance with the<br />
manufacturer’s instructions shall be IP51 for indoor installation and IP56 for<br />
outdoor installation.<br />
(iii) Assemblies shall be front access with top and/or bottom cable entry.<br />
(iv) Assemblies shall be floor mounted or wall mounted. Wall mounting is<br />
acceptable only if the frontal area of the assembly has an area less than 2<br />
square metres.<br />
(v) For outdoor switchboards containing busbars, pollution degree 3 shall apply<br />
at locations further than 1km in a direct line from the coast or at altitudes<br />
below 1000 metres. Otherwise, pollution degree 4 shall apply.<br />
For indoor switchboards, pollution degree 3 shall apply.<br />
(vi) The following safety measures against direct contact shall apply:<br />
• Requirement of a key or tool to gain entry into the switchboard. (Meet<br />
clause 7.4.2.2.3 a) of AS/NZS 3439.1:2002.)<br />
• Shielding all live parts in such a manner that they cannot be<br />
unintentionally touched when the door is opened or the cover is<br />
removed. (Meet clause 7.4.2.2.3 c) of AS/NZS 3439.1:2002.)<br />
(vii) Assemblies shall be Partially Type Tested Assemblies or Type Tested<br />
Assemblies with type test certificates or satisfactory test reports for the type<br />
tests listed in clause 8 of AS/NZS 3439.1:2002. Documentation shall be<br />
available to demonstrate that the results of type tests were satisfactory. The<br />
testing facility shall be accredited by NATA or registered with the<br />
Association of Short-Circuit Testing Authorities.<br />
(viii) The standard Internal Arcing-Fault Test specified in Annex ZD of AS/NZS<br />
3439.1:2002 (limited arc, initiated on the load side of a protective device<br />
within the functional unit being tested) shall be met and a test certificate<br />
demonstrating that the results of the type tests were satisfactory shall be<br />
available. The testing facility shall be accredited by NATA or registered with<br />
the Association of Short-Circuit Testing Authorities.<br />
202.1.3 Custom-built Assembly Type “CU”<br />
The following details shall apply to Custom-built Assemblies Type “CU”:<br />
Note that type test certificates or satisfactory test reports for the type tests listed in<br />
clause 8 of AS/NZS 3439.1:2002 are not required.<br />
(a) A Type “CU” assembly shall be a stationary “cubicle-type assembly” as defined in<br />
AS/NZS 3439.1:2002.<br />
(b) A Type “CU” assembly shall comply with AS/NZS 3439.1:2002 as defined by the<br />
following requirements:<br />
(i) Form of separation shall be Form 1.<br />
(ii) The degree of protection after installation in accordance with the<br />
manufacturer’s instructions shall be IP51 for indoor installation and IP56 for<br />
outdoor installation.<br />
Page 28<br />
<strong>MEW</strong> <strong>E101</strong>