DigitroniK Digital Indicating Controller SDC40A

More documents

Recommendations

Info

Auxiliary No. of output points 1 or 2 (1 point in 2G, 3D, AK, 5K, 9K, and BK models) output Type of output Selectable from PV, SP, DEV, RSP, MV and MFB. Output rating Output accuracy Output resolution Inrush current Maximum output current Minimum output current Opening terminal voltage 4 to 20mA dc. Max. allowable load resistance: 680Ω ±0.1%FS (under standard conditions) 1/10000 (numeric value of independent resolution; for example, the input resolution of PV or MFB is not included) 25mA max. 50ms max. (with 250Ω load) 21.6mA 2.4mA Output update cycle 0.1s 25V max. Communica- Communication Communication protocols RS-485 (Note 1) RS-232C tion system Network Multidrop The device is provided only with the slave station function, 1 to 16 units max. (DIM), 1 to 31 units max. (CMA, SCM). The device is provided only with the slave station function Data flow Half duplex Half duplex Synchronization Start/stop synchronization Start/stop synchronization Interface system Transmission system Balanced (differential) Unbalanced Data line Bit serial Bit serial Signal lines 5 transmit/receive lines (3-wire connec- 3 transmit/receive lines tion is also possible) Transmission speed 4800, 9600 bps 4800, 9600 bps Communication distance 500m max. (total) 15m max. Protocol RS-485 RS-232C Message characters Character configuration 11 bits/character 11 bits/character Format 1 start bit, even parity, and 1 stop bit, 1 start bit, even parity, and 1 stop bit, or 1 start bit, no parity, and 2 stop bits or 1 start bit, no parity, and 2 stop bits Data length 8 bits 8 bits Isolation Completely isolated between the input and output. Note 1. For RS-485, communications, the device can be connected not only to computers equipped with RS-485, but also to Yamatake Corporation's MX200, MA500 (DK link II DIM) or CMC10 controllers. General Memory backup Non-volatile semiconductor memory (EEPROM) specifica- Rated power voltage AC model: 90 to 264V ac 50/60Hz, DC model: 21.6 to 26.4V dc tions Power consumption AC model: 30VA max., DC model: 12W max. Power switching 15A max. 10ms (under operating conditions) inrush current Caution: When applying power to a number of <strong>SDC40A</strong>s simultaneously, ensure sufficient power is supplied, or start up the <strong>SDC40A</strong>s in series. Otherwise, the controllers may not start up normally due to voltage drop from the inrush current. It is necessary to reach the stable voltage within 2s of power being supplied. Insulation More than 20MΩ between power terminal 1 or 2 and ground terminal 3 (using 500V dc megger). resistance Dielectric strength 1500V ac (AC model) or 500V ac (DC model), 50/60Hz for 1 min between power terminal and ground terminal 1500V ac, 50/60Hz for 1 min between relay output and ground terminal 500V ac, 50/60Hz for 1 min between any other part and ground terminal 500V ac, 50/60Hz for 1 min between isolated terminals Standard conditions Ambient temperature 23 ±2°C Ambient humidity 60 ±5% RH Rated power voltage AC Model 105V ac ±1% Power frequency Vibration resistance 0m/s 2 Shock resistance 0m/s 2 DC Model 24V dc ±5% AC model: 50 ±1Hz or 60 ±1Hz Mounting angle Reference plane (vertical) ±3° Operating Ambient temperature range 0 to 50°C conditions Ambient humidity range 10 to 90% RH (non-condensing) Rated power voltage AC Model 90 to 264V ac Power frequency DC Model 50 ±2Hz or 60 ±2Hz Vibration resistance 0 to 1.96m/s 2 Shock resistance 0 to 9.81m/s 2 21.6 to 26.4V dc Mounting angle Reference plane (vertical) ±10° Transport/storage Ambient temperature range –20 to +70°C conditions Ambient humidity range 10 to 95% RH (non-condensing) Materials of mask and case Vibration resistance Shock resistance Package drop test Mask: Multilon Case: Polycarbonate 0 to 4.90m/s 2 (10 to 60Hz, for 2hr each in X, Y and Z directions) 0 to 490m/s 2 (3 times in vertical direction) Drop height: 90cm (1 angle, 3 edges, 6 planes, freefall) 6
General Colors of mask Mask: Dark gray specifica- and case Case: Light gray tions Mounting Panel flush type, using the dedicated mounting bracket Weight Approx. 750g (Extension terminal base: Approx. 150g) Standard Name Model No. Q'ty Name Model No. accessories Unit indicating label N-3132 1 Options Hard dust-proof cover set 81446083-001 Mounting bracket 81405411-001 2 Soft dust-proof cover set 81446087-001 Instruction manual CP-UM-1580E 1 Terminal cover 81446084-001 PC loader SLP-C40AJ20 Table of Selectable Inputs and Ranges Symbol °C Range °F Range K (CA) 0.0 to 1200.0 0 to 2400 K (CA) 0.0 to 800.0 0 to 1600 K (CA) 0.0 to 400.0 0 to 750 K (CA) –200.0 to +1200.0 –300 to +2400 K (CA) –200.0 to +300.0 –300 to +700 K (CA) –200.0 to +200.0 –300 to +400 E (CRC) 0.0 to 800.0 0 to 1800 J (IC) 0.0 to 800.0 0 to 1600 T (CC) –200.0 to +300.0 –300 to +700 B (PR30-6) 0.0 to 1800.0 0 to 3300 R (PR13) 0.0 to 1600.0 0 to 3100 S (PR10) 0.0 to 1600.0 0 to 3100 W (WRe5-26) 0.0 to 2300.0 0 to 4200 W (WRe5-26) 0.0 to 1400.0 0 to 2552 PR40-20 0.0 to 1900.0 0 to 3400 Ni-Ni · Mo 0.0 to 1300.0 32 to 2372 N 0.0 to 1300.0 32 to 2372 PL II 0.0 to 1300.0 32 to 2372 DIN U –200.0 to +400.0 –300 to +750 DIN L –200.0 to +800.0 –300 to +1600 Gold iron-chromel 0.0 to 300.0K — The ±0.1% FS input indication accuracy is not applicable to the following input conditions: Lower than –100°C on K thermocouple and T thermocouple: ±1°C ±1U Lower than 260°C on B thermocouple: ±4.0% FS ±1U 260°C to 800°C of B thermocouple: ±0.4% FS ±1U 800°C to 1800°C of B thermocouple: ±0.2% FS ±1U Lower than 100°C on R thermocouple and S thermocouple: ±0.2% FS ±1U 100 to 1600°C on R thermocouple and S thermocouple: ±0.15% FS ±1U Lower than 300°C on PR40-20 thermocouple: ±2.5% FS ±1U 300 to 800°C on PR40-20 thermocouple: ±1.5% FS ±1U 800 to 1900°C on PR40-20 thermocouple: ±0.5% FS ±1U Gold iron-chromel: ±1.5K ±1U The range of two decimal digits of RTD input: ±0.15%FS ±1U 0 to 10mV range: ±0.15%FS ±1U Lower than –100°C on DIN U: ±2°C ±1U Between –100°C and 0°C on DIN U: ±1°C ±1U Lower than –100°C on DIN L: ±1.5°C ±1U Symbol °C Range °F Range –200.0 to +500.0 –300.0 to +900.0 –200.0 to +200.0 –300.0 to +400.0 –100.0 to +150.0 –150.0 to +300.0 JIS '89 Pt100 –50.0 to +200.0 –50.0 to +400.0 (IEC/DIN) –60.00 to +40.00 –76.00 to +104.00 –40.00 to +60.00 –40.00 to +140.00 0.0 to 500.0 0.0 to 900.0 0.0 to 300.0 0.0 to 500.0 0.00 to 100.00 0.00 to 200.00 –200.0 to +500.0 –300.0 to +900.0 –200.0 to +200.0 –300.0 to +400.0 –100.0 to +150.0 –150.0 to +300.0 –50.0 to +200.0 –50.0 to +400.0 JIS '89 JPt100 –60.00 to +40.00 –76.00 to +104.00 –40.00 to +60.00 –40.00 to +140.00 0.0 to 500.0 0.0 to 900.0 0.0 to 300.0 0.0 to 500.0 0.00 to 100.00 0.00 to 200.00 4 to 20mA 0 to 20mA 0 to 10mV –10 to +10mV Scaling setting range –19999 to +26000 0 to 100mV (Decimal point position is variable.) 0 to 1V (Reverse scaling possible) –1 to +1V 1 to 5V 0 to 5V 0 to 10V 7
Page 1 and 2: No. CP-SS-1580E DigitroniK Digital
Page 3 and 4: Analog Type of input 4 to 20mA or 1
Page 5: Event No. of output 2 points: stand
Page 9 and 10: ■ Dimensions C40A Hard dust-proof
Page 11 and 12: Extension terminal layout • With

DigitroniK Digital Indicating Controller SDC40A

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?