Cooling Systems - HYDAC USA

More documents

Recommendations

Info

Plate Heat Exchangers 20 550 HEX Series Technical Data Size 610 P (HP) 100 90 80 70 60 50 40 30 20 10 0 Size 615 P (HP) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Size 422 P (HP) Oil : ISO VG 46 Oil temp in : 140°F Water temp in : 70°F Oil/Water flow = 4 delta p oil < 23 psi 10 20 0 5 10 15 20 25 30 35 40 45 50 55 60 Oil : ISO VG 46 Oil temp in : 140°F Water temp in : 70°F Oil/Water flow = 4 delta p oil < 23 psi 10 20 30 30 Oil flow (gpm) 40 50 120 100 70 0 5 10 15 20 25 30 35 40 45 50 55 60 320 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 Oil : ISO VG 46 Oil temp in : 140°F Water temp in : 70°F Oil/Water flow = 4 delta p oil < 23 psi 20 40 50 Oil flow (gpm) 30 60 60 100 80 0 20 40 60 80 100 120 140 40 Oil flow (gpm) 50 150 120 100 80 60 The cooling capacity is also dependent on the viscosity class. At a lower viscosity class the cooling capacity increases, at a higher viscosity class it decreases. In order to make an accurate calculation, the following details are required: • type of oil • premissable tank temperature • required outlet temperature of the oil or necessary cooling capacity • inlet temperature of the water and maximum water quantity. Number of plates (N) H = 10 + Nx2.4 (mm) lbs 10 34 5.5 20 58 8.4 30 82 11.2 40 106 14.0 50 130 17.0 60 154 19.8 70 178 22.6 100 250 31.2 120 298 37.0 Number of plates (N) H = 10 + Nx2.4 (mm) lbs 10 34 9.2 20 58 14.3 30 82 19.4 40 106 24.4 50 130 29.7 60 154 35.5 80 202 44.6 Number of plates (N) Selection Program H = 10 + Nx2.85 (mm) lbs 20 67 34.7 30 95.5 44.5 40 124 54.1 50 152.5 63.8 60 181 73.5 80 238 92.8 100 295 112.2 The cooler selection program calculates the correct heat exchanger in the case of non-standard operating data. Please contact our technical sales department. System requirements: • Windows 95/ • Windows NT/ • Hard disk memory • 8 MB RAM 48 INNOVATIVE FLUID POWER PN#02085359 / 12.12 / COL1112-1396
Plate Heat Exchangers Dimensions Size 610 12.20” (310mm) 9.84” (250mm) Mounting Bracket 610 Mounting Bracket DIN912-M8x70 4.37” 1.97” (111mm) (50mm) S3 S2 S4 S1 4.92” (125mm) SW41 13.03” (331mm) 0.87” (22mm) 0.94” (24mm) 1.18” (30mm) Size 615 Mounting Bracket 615 Mounting Bracket 20.71” (526mm) 18.35” (466mm) DIN912-M8x70 4.37” 1.97” (111mm) (50mm) S3 S2 S4 S1 4.92” (125mm) SW41 21.50” (546mm) 0.87” (22mm) 0.94” (24mm) 1.18” (30mm) Size 422 24.33” (618mm) 20.43” (519mm) Mounting Bracket 422 Mounting Bracket DIN912-M8x70 7.52” 3.62” (191mm) (92mm) S3 S2 S4 S1 8.15” (207mm) SW41 25.12” (638mm) 1.10” (28mm) 1.18” (30mm) 1.18” (30mm) Dimensions are for general information only, all critical dimensions should be verified by requesting a certified print. Dimensions are in inches. PN#02085359 / 12.12 / COL1112-1396 Please note: For mounting heat exchangers with 60 plates and above, two clamps are recommended. INNOVATIVE FLUID POWER 49
Page 1 and 2: PN#02085359 / 12.12 / COL1112-1396
Page 3 and 4: Table of Contents HYDAC Coolers Ove
Page 5 and 6: Overview Applications Mobile Applic
Page 7 and 8: Coolers Model Code Model ELD = Air
Page 9 and 10: Coolers General Housing Welded stee
Page 11 and 12: Coolers ELD Series Dimensions Sizes
Page 13 and 14: Coolers Model Code Model ELH = Air
Page 15 and 16: Coolers General Construction Housin
Page 17 and 18: Coolers ELH Series Dimensions Sizes
Page 19 and 20: Coolers Model Code Model OKC = Air
Page 21 and 22: Coolers General • Electrical conn
Page 23 and 24: Coolers OKC Series Dimensions Sizes
Page 25: Plate Heat Exchangers Model Code Se
Page 29 and 30: Plate Heat Exchangers Model Code Se
Page 31 and 32: Plate Heat Exchangers Series Dimens
Page 33 and 34: Heat Exchangers Gasketed Plate Heat
Page 35 and 36: Combi-Coolers Combi-Coolers Technic
Page 37 and 38: OKC / OK / ELD / ELH Series Crossov
Page 39 and 40: HYDAC the Reliable Partner for Wind

Cooling Systems - HYDAC USA

Create successful ePaper yourself

Delete template?

Save as template?