Ion boiler STAFOR user manual

ION-BOILER STAFOR TECHNICAL PASSPORT V 12.11.
according with EN 60335 – 1, EN 60335 – 2 – 35
1. The ion-boiler STAFOR (further – the boiler) is provided for installation
only in buildings with one phase (1P) or three phase (3P) – depends on
model of boiler, variable voltage electric current input.
2. For connection to electric current there is obligatory earth connection
(further – earthing).
3. Heating system with the ion-boiler STAFOR must be installed according
with this technical passport (further – TP).
4. Filling the heating system must be done by special heat carrier
STATERM EKO E40, it is prohibited to use water. Using water causes
malfunction of the boiler.
5. After filling of the heating system with heat carrier, it is obligatory to
measure consumable voltage with amper-meter.
6. Work of the boiler STAFOR is not allowed in heat carrier simmer`s
regime.
7. It is prohibited to strew the heat carrier STATERM EKO E40 with water
or any other liquid.
WARNING!
Before the purchase of the ion-boiler it is necessary to make sure that
there is possibility to connect it. For it is obligatory to consult with
specialists about the necessary electrical capacity.
The voltage of the ionic boiler is 230 V or 400V variable electric current.
The maximal work capacity of the boilers depends from the heat
carrier`s measurements.
The maximal work power of the ion-boiler depends from the heat
carrier`s measurements.
There is obligatory EARTHING.
It is prohibited to connect the ion-boiler at the continuous current.
1. INTRODUCTION
1.1. This technical passport is provided to inform the buyers about the
technical data of the ion-boiler STAFOR and contains the information
about the manufacturer guarantee, indications that are necessary to
be observed during assembly of the boiler.
1.2. The boiler is provided for heat carrier STATERM EKO E40 heating in
residential and non-residential room heating systems with the
maximal heating capacity showed in table, under condition, that the
rooms are well insulated.
2. GENERAL GUIDELINES
2.1. At the purchase moment of the ionic boiler STAFOR, in the presence
of the buyer, there should be checked the complete set according with
TP item 4.
2.2. After the purchase of the boiler there is not accepted any claims about
the completion set and outer technical damages.
2.3. Before connection of the boiler it is recommended to acquaint with
this TP, instructions and normative acts.
3. THE TECHNICAL DATA
3.1. The main technical data of the boiler, indicated in the table Nr. 1.
3.2. The ion-boiler STAFOR is electrode – ionic, flow type, liquid heater.
The heating of the heat carrier in the boiler is due to electric power
and flow of heat carrier ions.
4. PIECING
4.1. In the completion set of the ion-boiler STAFOR include:
4.1.1. The boiler;
4.1.2. The technical passport (TP), together with user manual;
4.1.3. Package.
5. SAFETY MEASUREMENTS
5.1. The connection of the boiler to the electric network should be done
only by a specialist – electrician, according with the existing EU
normative acts.
5.2. During service it is obligatory to switch off the boiler from electric
current.
5.3. The ion-boiler must have earthing.
5.4. During exploitation it is PROHIBITED:
5.4.1. to use the boiler without earthing;
5.4.2. to use the boiler without electric network automatic
machine;
5.4.3. to use the boiler in electric network without not insulated
clamps;
5.4.4. to install the valve on the output of the boiler before
protection group;
5.4.5. to pour in or to pour out heat carrier without switching off
the boiler.
5.5. Not to allow to get liquid on the surface of the boiler.
5.6. It is not recommended to use in one system two or more of different
capacity boilers.
5.7. It is PROHIBITED to exploit the heat system:
5.7.1. without protection group;
5.7.2. in case of leakage of heat carriers.
5.8. In case of damage of electric wires they should be replaced with the
help of certified electrician.
6. THE ORDER OF INSTALLATION
6.1. Assembly of heat system:
6.1.1. The assembly of the heat system must be made by
specialist – a plumber. Heat system must be pure clean,
without mechanical dirt, preservatives, water or any other
heat carrier. If required heating system must be rinsed.
6.1.2. The installation of the ion-boiler must be done in
accordance with figure 11.1 and normative acts.
6.1.3. The connections of boiler threads and heating system
must be hermetic. After assembly of the heating system it
is necessary to check hermetism. All leakages must be
avoid.
6.2. The boiler must be installed in the distance of 250 mm from any
combusting materials.
6.3. Connection of the ion-boiler at the electric network:
6.3.1. For protection of the ion-boiler there is not allowed to use
B type automatic machines.
6.3.2. Connection of the boiler to the electric network should be
done by certified electrician according with EU normative
acts and instructions.
6.3.3. Control panel connection must be made in accordance
with connection schema.
6.3.4. The boiler has to be connected into the electric network
at least with the minimum diameter of wire obligatory to
the consumption of boiler. Also the earthing should be
done with a cable of a proper diameter. One should
consult with specialist for the proper diameter.
6.3.5. WARNING! The connection of the boiler must be made
according with the labels on the boiler and control panel.
EARTHING – OBLIGATORY!
6.3.6. Earthing device resistance must be not more than 4 Om.
6.3.7. Connection cable type – T (heat resistant).
7. TRANSPORTATION AND STORAGE
7.1. Packaged boiler transportation is allowed by railway or vehicles, under
condition that products are protected from humidity and mechanical
damages according with transportation regulations.
7.2. To store the boilers in dry, heated rooms with temperature +5 to
+40°C.
7.3. The storage of the ion-boilers must be provided in secure place.
7.4. It is prohibited to store product without package.
7.5. The admissible storage time till repacking is 10 years from
manufacture.
8. GUARANTEE LIABILITIES
8.1. “STAFOR” Ltd gives warranty for ion-boiler - 24 month time from the
date of purchase under condition that there are observed regulations
stated in TP.
8.2. In manufacture defect case, the user of the boiler has to turn to
certified distributor or “STAFOR” Ltd.
8.3. In guarantee time there will not be accepted any claims in the
following cases:
8.3.1. non-existence of filled document about purchase or
guarantee document;
8.3.2. return of not full completion set, according to 4.1. (except
4.1.3.);
8.3.3. in case of mechanical damages (scratch, paint peel off,
pleats, etc.);
8.3.4. in case of broken seal (paint on screws, holographic labels
STAFOR);
8.3.5. self-dependent dismantle of the boiler;
8.3.6. if there are not observed user, assembly and simmer
regime regulations (that can be defined by certified
distributor).
8.4. The guarantee document (this TP, etc.) must be taken only by
“STAFOR” or certified distributor worker and only in case of boiler
defect.
8.5. “STAFOR” ltd is responsible only for STAFOR ion-boiler, not for any
other part of heating system.
9. OTHER INFORMATION
9.1. The boiler corresponds with the standards of EU EN 60335-1, EN
60335-2-35 – test report Nr. T37D08, T25D07.
9.2. Ion boiler STAFOR is internationaly patented. All rights reserved.
9.3. The identification number of the ionic boiler is stated in front of TP.