warning - Bishop Lifting Products, Inc.

More documents

Recommendations

Info

Roundslings Warnings ROUNDSLING WARNINGS When inspecting a roundsling, it shall be taken out of service immediately and returned for repair or replacement when any of the below defects are present Missing or illegible sling identification (tag) Weld splatter that exposes core yarns Knots in any part of the sling Acid or caustic burns Fittings that are pitted, corroded, cracked, bent, twisted, gouged, or broken Evidence of heat damage Damaged hooks per ASME B30.10 Holes, tears, cuts, abrasive wear, or snags that expose core yarns Broken or damaged core yarns Damaged rigging hardware per ASME B30.26 and… Any condition that causes doubt about the continued use of the sling Roundslings Roundslings 126 (800) 972-1041
Roundslings Identification, Inspection, Rigging Practices Roundslings Identification, Inspection, Rigging Practices Synthetic Web Slings are designed and built to be easy to use and versatile. As with any quality product certain precautions and standards of treatment should be observed. Proper care will extend the useful life of roundslings. Follow the Guidelines set forth in ASME B30.9 “Slings” standard, OSHA 1910.184 and 1926.251. Sling Identification Each sling shall be marked to show the following: • Name or Trademark of manufacturer • Manufacturer’s code or stock number • Rated loads for the type(s) of hitch(es) used and the angle upon which it is based • Core material • Cover material, if different from core material • Number of legs, if more than one Sling identification shall be done by the sling manufacturer, and should be maintained by the user so as to be legible during the life of the sling. Inspection Synthetic Web Sling inspection falls into 3 categories. Initial, Frequent, and Periodic. • Initial Inspection– Prior to use, all new, altered, modified, or repaired slings shall be inspected by a designated person to verify compliance with the applicable provisions of this chapter • Frequent Inspection o A visual inspection for damage shall be performed by the user of other designated person each day or shift the sling is used o Conditions such as those listed in the removal criteria section or any other condition that may result in a hazard shall not be returned to service until approved by a qualified person o Written records are not required for frequent inspections • Periodic Inspections o A complete inspection for damage to the sling shall be periodically performed by a designated person. Each sling and component shall be examined individually, taking care to expose and examine all surfaces. The sling shall be examined for conditions such as those listed in the removal criteria section and a determination made as to whether they constitute a hazard o Periodic Inspection Frequency – Periodic inspection intervals shall not exceed 1 year. The frequency of periodic inspections should be based on: o • Frequency of sling use • Severity of service condition • Nature of lifts being made • Experience gained on the service life of slings used in similar circumstances Guidelines for time intervals are: • Normal service – yearly Severe service – monthly to quarterly • • Special service – as recommended by a qualified person o A written record of the most recent periodic inspection shall be maintained Removal Criteria A roundsling shall be removed from service if the following conditions are present. • Missing or illegible sling identification (tag or markings) Acid or caustic burns • • Evidence of heat damage • Holes, tears, cuts, or snags that expose the core yarns • Broken or damaged core yarns • Weld splatter that exposed core yarns • Roundslings that are knotted • Fittings that are pitted, corroded, cracked, bent, twisted, gouged, or broken • Damaged hooks, removal criteria as stated in ASME B30.10 • Damaged rigging hardware, removal criteria as stated in ASME B30.26 • Other conditions, including visible damage, that cause doubt as to the continued use of the sling Roundslings Rigging Practices • Slings shall be shortened or adjusted only by methods approved by the sling manufacturer or a qualified person • Slings shall be hitched in a manner providing control of the load • Slings in contact with edges, corners, or protrusions should be protected with a material of sufficient strength, thickness, and construction to prevent damage to the sling • Shock loading should be avoided (800) 972-1041 Roundslings 127
Page 1:
Slings Catalog Slingmax ® Rigging
Page 4:
Table of Contents Slingmax ® Riggi
Page 7 and 8:
Single-Path ® Extra Covermax ® wi
Page 9 and 10:
Twin-Path ® Sparkeater ® SLINGMAX
Page 11 and 12:
Twin-Path ® Eye & Eye Length (Feet
Page 13 and 14:
FIBER OPTIC INSPECTION FOR ALL TWIN
Page 15 and 16:
Sliding Sleeves Synthetic Armor Pad
Page 17 and 18:
Tri-Flex ® Length (Feet - In) SLIN
Page 19 and 20:
Gator-Max Length (Feet - In) SLING
Page 21 and 22:
Gator-Flex ® Grommets SLINGMAX ®
Page 23 and 24:
Chain Sling Saddle Ring SLINGMAX ®
Page 25 and 26:
Environmental Considerations Enviro
Page 27 and 28:
Inspections and Test Procedures of
Page 29 and 30:
Wire Rope Slings
Page 31 and 32:
Wire Rope Slings Single Leg Length
Page 33 and 34:
Wire Rope Slings Single Leg with Sl
Page 35 and 36:
Wire Rope Slings Single Leg 8-Part
Page 37 and 38:
Wire Rope Slings Three Leg 8-Part B
Page 39 and 40:
Wire Rope Slings Two Leg Bridles Le
Page 41 and 42:
Wire Rope Slings Three Leg Bridles
Page 43 and 44:
Wire Rope Slings Bridles with Sorti
Page 45 and 46:
Wire Rope Slings Socket Lines with
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Wire Rope Slings Single Leg Sling w
Page 53 and 54:
Wire Rope Slings Grommets Length (F
Page 55 and 56:
Wire Rope Slings Grommets Length (F
Page 57 and 58:
Identification, Inspection, Wire Ro
Page 59 and 60:
Wire Rope Slings Weight Tables Sing
Page 61 and 62:
Wire Rope Slings Weight Tables Two
Page 63 and 64:
Wire Rope Slings Weight Tables Sock
Page 65 and 66:
Alloy Chain Slings Grade 80 and Gra
Page 67 and 68:
Alloy Chain Slings Single Leg Types
Page 69 and 70:
Alloy Chain Slings Triple Leg Type:
Page 71 and 72:
Alloy Chain Slings Single Adjustabl
Page 73 and 74:
Alloy Chain Slings Double Adjustabl
Page 75 and 76:
Alloy Chain Slings Single & Double
Page 77 and 78: Alloy Chain Slings Double Leg with
Page 79 and 80: Alloy Chain Slings Endless Chain Sl
Page 81 and 82: Alloy Chain Slings Warnings ALLOY C
Page 83 and 84: Alloy Chain Slings Identification,
Page 85 and 86: Alloy Chain Slings Important Terms
Page 87 and 88: Alloy Chain Slings Weight Tables Do
Page 89 and 90: Alloy Chain Slings Weight Tables Do
Page 91 and 92: Web Slings
Page 93 and 94: Web Slings Steel Basket Fittings Le
Page 95 and 96: Web Slings Aluminum Basket Fittings
Page 97 and 98: Web Slings Polyester with Flat Eyes
Page 99 and 100: Web Slings Polyester with Twisted E
Page 101 and 102: Web Slings Polyester Endless Length
Page 103 and 104: Web Slings Polyester Reversed Eye L
Page 105 and 106: Web Slings Two Leg Nylon Web Bridle
Page 107 and 108: Web Slings Four Leg Nylon Web Bridl
Page 109 and 110: Web Slings Sliding Sleeves SWC1 Sli
Page 111 and 112: Web Slings Sliding Sleeves Syntheti
Page 113 and 114: Web Slings Warnings WEB SLING WARNI
Page 115 and 116: Web Slings Identification, Inspecti
Page 117 and 118: Web Slings Weight Tables CHS - Web
Page 119: Web Slings Weight Tables 3B - Three
Page 122 and 123: Roundslings Polyester Roundslings L
Page 124 and 125: Roundslings Sliding Sleeves SWC1 Sl
Page 126 and 127: Roundslings Sliding Sleeves Synthet
Page 130 and 131: Roundslings Identification, Inspect
Page 132 and 133: Metal Mesh Slings Metal Mesh Slings
Page 134 and 135: Metal Mesh Slings Warnings METAL ME
Page 136 and 137: Metal Mesh Slings Identification, I
Page 138 and 139: Technical Information Definitions o
Page 140 and 141: Technical Information Rigging Infor
Page 142 and 143: Technical Information Weights of Ma
Page 144 and 145: Training Aids Rigging Hardware Tr
Page 146 and 147: Training Aids Hitches & Capacities
Page 148 and 149: Training Aids Crane Hand Signals Mo
Page 152: Bishop Lifting Products, Inc. 125 M
show all

warning - Bishop Lifting Products, Inc.

Create successful ePaper yourself

Delete template?

Save as template?